IS, : 801 - 1876

Indian Standard

Rcdii

1995 )

CODE OF PRACTICE FOR USE OF COLD-FORMED LIGHT GAUGE STEEL STRUCTURAL MEMBERS IN GENERAL BUILDING CONSTRUCTION (

First Revision )
1998

Seventh Reprint DECEMBER

( Incorporating Amendment No. 1 )

UDC

624014.2

: 693.814

: 69tOOl*3

BUREAU
MANAK

OF
BHAVAN.

INDIAN

STANDARDS
ZAFAR MARG

9 BAHADUR SHAH NEW DELHI 110002

Gr 8

January 1976

IS : 801-1975

Indian Standard
CODE OF PRACTICE FOR USE OF COLD-FORMED LIGHT GAUGE STEEL STRtJCTURAL MEMBERS IN GENERAL BUILDING CONSTRUCTION

(First Revision)
Structural Engineering Sectional Committee, SMBDC 7
Chairman DXECTOR STANUARDS (CIVIL) Representing Ministry of Railways

Members Industrial Pasteners Association of India, Calcutta SHRI L. N. AGRAWAL SHRI M. M. MURARKA (Alternate) Metallurgical and Engineering Consultants (India) SHRI A. K. BANERJEE Ltd, Ranchi SHRI S. SANKARAN(Alternate) Department of Transport (Road Wing), Ministry SHRI P. C. BHASIN of Shipping & Transport SHR~ .4. S. BISHNOI(Alternatej Government of West Bengal ;; ; p C$TJEE Central Mechanical Engineering Research Institute . . . (CSIR), Durgapur Indian Institute of Technology, Kanpur DR P. DAYARATNA~I Ail. N. Dastur & Co Pvt Ltd, Calcutta SHRI D. S. DESAI Irrigation & Power Department, Government of DIRECTOR (MERI) Ma!rarashtra, Bombay RESEARCHOFFICER (Alternate) Central Water & Power Commission (Power DIRECTOR (TCD) Wing), New Delhi SHRI P. V. N. IYENGER (Alternate) Central Public Works Department, New Delhi EXECUTIVE ENGINEER (CENTRAL STORESDIVISIONNo. II) Stewarts & Lloyds of India Pvt Ltd, Bombay SHRI M. M. GHOSH S~IRI S. C. GHOSH (Alternate) Bridge & Roof Co (India) Ltd, Howrah SHRI A. G. GONSALVES SHRI S. S. BOSE (Alternate) Public Works Department, Government of West Sam SAILAPAT~GUPTA Bengal, Calcutta (Con&ed (9 Copyright OF INDIAN 1982 on page 2)

STANDARDS This publicatign is protected under the Indian Copyright Act (XIVof 1957) and reproduction in *hole or in part by any means except with written permission of the publisher shall be deemed to be an infringement of copyright under the said Act.

BUREAU

ls

801- 1975

(Conlinued jrom page 1)

Members Representing The Hindustan Construction Co Ltd, Bombay Snm G. S. IYER SHRI S. M. GULATEE (Al&a&) DR 0. P. JAIN Institution of Engineers (India), Calcutta JOINT DIRECTORSTANDARDS (B&S) Ministry of Railways DEPUTY DIRECTORSTANDARDS (B&S)-11 (A!fernalc) Bombay Municipal Corporation, Bombay SHRI S. D. KALE SHRI M. K. R. SHARMA(Allentale) . _ Electrical Manufacturing Co Ltd, Calcutta SHRI CLu GHOWA SHRI S. N. SINGH (Alternafe) Engineer-in-Chiefs Branch, Army Headquarters, PROF K. D. MAHAJAN New Delhi PROF 8. V. RAMASWAMY (Alternate) National Buildings Organisation, New Delhi SHRI G. c. MA~WJR Srmr K. S. ~RISIVASAN (Aitcrnatc) SHRI P. K. MALLICK Jessop & Co Ltd, Calcutta SH~I A. P. KAYAL (Allernalc) Indian Institute of Technology, Kharagpur DR S. K. MALI.ICI( Mantons (Bangalore) Prt Ltd, Bangalore SHRI N. V. MANAY Hindustan Steel Ltd, Durgapur SBRI A. K. MITRA Braithwaite & Co (India) Ltd, Calcutta SHRI P. K. M~KHEHJEE SHRI P. T. PATEL (Alfrmafe) SHRI P. R. NATAR.~JAN Struc~o~~hetrgineering Research Centre (CSIR), DR J. PURUSHOTHAM
DEPUTY DIRECTOR (GATES & DESIGN) (Alternate)

Central Water & PowerCommission New Delhi Richardson

(Water Wing),

REPRESENTATIVE SIIRI P. V. NAIK (Alfcmate)

& Cruddas Ltd, Bombay

Burn & Co Ltd, Howrah KEPRE~ENTATIVE Jadavpur University, Calcutta PROF P. K. SonI Indian Roads Congress, New Delhi SHRI T. N. SUBBA RAO DR D. JOHNSON VICTOR (Altemati) SUPERINTENDING EN G I N E E R (PLANNING& DESIGNCIRCLE) E~EC~TIVIZ ENGINEER DIVISION) (Ahnafe)
(RUILDXNC. CENTRE MAJ R. P. E. VAZIFDAR

Government

of Tamil Nadu, Madras

SHRI K. VEERARAO~VACHARI SHRI S. N. VOHRA Snar S. N. BA~U (Alkrnatc)

SHRI L. D. WADHWA SHRI B. B. NAO (Alternate) SHRI C. R. RAMA RAO,

Bombay Port Trust, Bombay Bharat Heavy Electricals Ltd, Tiruchirapally Inspection Wing, Directorate General of Supplies & Disposals (Ministry of Industries & Civil Supplies) Engineers India Ltd, N,ew Delhi Director General, BIS (Ex-n@io Member) Secretary

Director (Strut & Met)

Assistant Director

SHRI S. S. SETH1

(Strut & Met),

BIS

(Continued on page 37)

IS

991-1975

Indian Standard
CODE OF PRACTICE FOR USE OF COLD-FORMED LIGHT GAUGE STEEL STRUCTURAL MEMBERS IN GENERAL BUILDING CONSTRUCTION

( First Revision)
0. FOREWORD
0.1 This Standards Structural Structural Council. Indian Standard (First Revision) was adopted by the Indian Institution on 31 January 1975, after the draft finalized by the Engineering Sectional Committee had been approved by the and Metals Division Council and Civil Engineering Divicion

0.2 Cold-formed steel structural members are cold-formed in rolls or press brakes from flat steel, generally not thicker than 12.5 mm. For repetitive mass production they are formed most economically by cold-rolling, while smaller quantities of special shapes are most economically produced on press brakes. The latter process, with its great versatility of shape variation, makes this type of conrtructionas adaptable to special requirements as reinMembers are connected by spot, fiilet, forced concrete is in its field of use. plug or slot welds, by screw, bolts, cold rivets or any other special devices. 0.3 This type of construction is appropriate more of the following conditions: a) and economical under one or

Where moderate loads and spans make the thicker, hot-rolled shapes uneconomical, for example, joists, purlins, girts, roXtrusses, complete framing for one- and two-storey residential, commercial and industrial structures; Where it is desired that load-carrying members also provide useful surfaces, for example, iioor panels and roof decks, mostly installed without any shoring and wall panels; and Where sub-assemblies of such plant, reducing site erection for example, sub-assembly of more for structures listed in utility buildings, etc. members can be prefabricated in the to a minimum of simple operations, panel framing up to 3 x 4 metros and (a), standardized package shed-type

b)

c)

Is : 801 1975
0.4 This standard was fiirst published in 19% and \vac mainly based on 1935 edition of Specification !;?r thr: clr..igrl uf cokl fmrd steel str7lcrural New York. members _i~uhlished by An7crican Iron a~1 Steel Jnstitute, Whi!e revlsmg the Tndian Standards, the Sectional Committee decided that it should be, brought in line with the 19X edi;ion of the AlST pul& .>:ion, as this has been the accepted practice in :hir i-ountry and most ,;uitabl,for this type of conwuction. a particular rq:lir.cmctnt 01 Ihij 0.5 For t!le purpose: of tim~din~ wldiet~ standard i.; coz-ty;iicd \\rith, the final valtw, ol~crvcd or calcolatcd, expressing thp resl71t of a test rJr analysis, shall be rounci~.tl of? in accnrdancc \virh IS : 2-i%O+. The number of significa IT pLact:s reixined in the rounded off value should be the sami- as that of the specitied vali~c in this standard.

1. SCQPE 1.1 This code applies shape from carbon or purposes in buildings. provided appropriate 2. MATERIAL 2.1 Structural steel sheet or strip steei rhall conform to IS : 1079-19737. 2.2 Steels other than the one co\fered in 2.1 may be used provided such steel conforms to the chemical and mechanical repuirements of IS : 107%1173t and its weldability is guaranteed. 3. DEFINITIONS 3.0 For the purpose of this code, the followicg definitions shall apply. 3.1 Stiffenedi Compression Elements --- A fiat compression e!ement, for example, a plane compression flange of a flexural member or a plane web or flange of a compression member, of which boLh edges parallel to t&e direction of stress sre stiffened by a web, flange stiXening lip, intermediate stiffener, or the like conforming to the requirements of 5.2.2. 3.2 Unstiffened Compression stiffened at only one edge parallel Elements --A to the direction to the design of structural rnembcrs cold-formed 10 low-alloy, sheet or strip steels used for load carrying It may also be used fijr structures, other than baildine allowances are made for dynamic effects.

of stress.

flat

element

which

is

3.3 Mubiple

Stiffened Elements - An element that is stiflened between webs, or between a web and a stiffened edge, by means of intermediate stiffeners which are parallel to the direction ofstrcss and which conform to A sub-element is the portion between adjacent the requirements of 5.2.2.2. stiffeners or between web and intermediate stiffener or between edge and intermediate stiffener. *Rules for rounding off numerical values (w&A). tspecification for hot rolled carbon sted sheet and strip (third revi&j.

IS : 84M - 1975 3.4 Flat-Width Ratio - The flat-width ratio, w/t, of a is the ratio of the flat-width, W, exclusive of edge fillets, In the case of sections, such as I, T channel and 5 shaped w is the width of the flat projection of flange from web, and of any stiffening lip that may be at the outer edge the case of multiple-web sectuons, such as hat: 0 or box width w is the flat-width of flange between adjacent webs, single ffat clement, to the thickness t. sections, the width exclusive of fillets of the flange. In shape sections, the exclusive of fillets.

3.5 Effective Design Width -- Where the M-width, w, of an element is reduced for design purposes, the reduced design width b is termed the effective width or the effective design width, and ix determined in accordance with 5.2.1 and 5.2.5. 3.6 Thickness -. The thickness t of any element or section shall be the base steel thickness, exclusive of coatings. 3.7 Torsional Flexural Buckling--A mode of buck!ing pression members can bend and twist simultaneously. 3.8 Point Symmetric Section -A (centroid) such as a ,c section .having 3.9 Yield Point, Fy section symmetrical equal flanges. ,in which about com-

a point

It shall mean yield point or yield strength. force per square

3.16 Stress -- Force per unit area; expressed in kilogram centimetre, abbreviated throughout as kgf/cma. 4. LOADS 4.1 For general guidance in the design of structures, IS : 875-19647. 5. DESIGN PROCEDURE

as to the various loads to be taken into account reference should be made to IS : 800-1962* 4

5.1 AlI computations for safe load, stress, deflection and the like shall be in accordance with conventional methods of structural design except as otherwise specified herein. 5.2 Properties of Sections - Yroperties of se&ions (cross-sectional area, moment of inertia, section modulus, radius of gyration, etc) shall be determined in accordance with conventional methods of structural design. Pro_ perties shall be based on the full cross section of the members (or net section where the use ofs net section is applicable) except where the use of a reduced cross section, or eflective design width, is required by the provisions of 5.2.1

and 5.2.5.
tcode

+t.ode.of.practice for use of structural steel in general building construction (reuise,Q

of practice for structural safety of buildings: Loading standards (m&f).

IS : sol - 1975
5.2.1 Progerties of St$ened Compression Elements - In computing properties of sections of flexural members and in computing values of Q (see 6.6.1.1) for compression members, t!le flat-width w of any stiffened compression element having a flat width ratio larger than (w/t)n, as hereinafter defined shall be considered as being reduced lor design purposes to an effective design width b or b, dctcrmined in accordance with the provisions of 5.2.1.1 or 5i2.1.2 whichever is applicable, and subject to the limitations of 5.2.5 where applicable. That portion of the total width which is considered removed to arrive at the effective design width shall be located symmetrically about the centre line of the element. 5.2.1.1 Elements without intermediate st$sners - The effective design widths of compression elements which are not subject to the provisions of 5.2.1.2 shall be determined from the following formulae* : For load determination: Flanges are fully effective (b = w) up to (zu/t)m,,=l than (w/t)li, 435/d For flanges with w/t larger

1
Exception: Flanges effective larger 6 of closed square (b=w) than 2 120 C and up to (w/t)ll, rectangular tubes are fully 1 540 = - 2/7 for flanges with w/t
1 _I

(w/t)li, 420

t -=z

(w/t) d7

1
1,850/d/f

When members or assemblies are subject to stresses produced by wind and earthquake forces, the effective design width b shall be determined for 0.75 times the stress caused by wind or earthquake loads alone, or 0.75 times the stress caused by wind or earthquake plus gravity loads, when use is made of the increased allowable stress permitted in 6.1.2.1 or 6.1.2.2. For deJection &termination: Flanges are fully effective up to (w/t)lf,,, = than (w/t)llm 600 (w/t) z/f For flanges with w/t larger

*It is to be noted that where the flat-width exceeds (lu/l),,, the propertics of the section shall frequently be determined by successive approximations or other appropriate methods, since the stress and the effective design width are interdependent.

ls
Exception: Flanges of closed square and rectangular 990/# 545 for

: 8019 1975
fully rujt

tubes are flanges with

effective up to (w/t)rtm=l larger than (rci/t)rtm 2 710 b --=_

where

z/f
ratio,

1 -

(w/t) d-y

w/t = flat-width
b = f =

effective design width in cm, and actual stress in the compression element computed basis of the effective design width in kgf/cm2.

on the

5.2.1.2 Multiple st$ened elements and ride stiflened elements with edge stz~encrs - Where the flat-width ratio of a sub-element ofa multiple stiffened compression element or of a stiffened compression element which does not have intermediate stiffeners and which has only one longitudinal edge connected to a web does not exceed 60, the effective design width, b, of such sub-element or element shall be determined in accordance with the provisions of 5.2.1.1. Where such flat-width ratio exceeds 60, the effective or element shall be determined from design width, be, of the sub-element the following formula*:

where

be -=-_t
flat-width ratio b= be =

b t

O*lO (5

60)

w/t

of sub-element

or element, in accordance or element witn the to bc used

effective design width determined provisions of 5.2.1.1 in cm, and effective design width of sub-element in design computations in cm.

For computing the effective structural properties of a member having compression sub-elements or element subject to the above reduction in effective width, the area of stiffeners (edge stiffener or intermediate stiffeners?) shall be considered reduced to an effective area as follows: For w/t betlveen 60 and 90: where 4 = (3 For w/t greater 2 be/w) 90: -4, = (be/w) At A,, 8 = 4 At [1_$]y

than

element stiffened zit one edge by other than a simple lip. tScs 5.2.2.2 for limitations on number of intermediate stiffeners which may be considered effective and their minimum moment of inertia.

*See 5.2.3(a) for limitations on the allowable flat-width ratio of a compression

113 the above expressions, A ef and A,+ relk wly to the area of the stiffener section, excluGve of any portion of a~lja~cns elements. The centmid of the stiffener is to be ccnsidered located at the centroid of the fkll acea of the stiffcnttr, and the moment of inertia of the stiffener about its own ccntroidal axis shall 1~ that of the full section of the stiffener. 5.22 Sta$kers j0r Com~ressiim Hemcnts 5.2.2.1 E&e .~~~j&rs--- In c~&r that a flat compression element may be considered a strricned compression element, it shall be stitlked along each longitudinal edge parai!el to the direction of stress by a web, lip, or other stiffening means, having the following minimum moment of inertia: &$ln -== 1.83 t4 z/~-281 where 1bfr, = minimum allowable moment of inertia of stiEener (of any shape) abotit its own centroidal axis parallel to the stiffened elem~:nt in cm4, and ratio of stiffened element.

---_.

203/F,. but not less than

9.2 t*

w/t = fhat-width

Where the stitfencr consists of a simple lip bent at right nn,gle~ to the stirencd. element, the required overal ! tlcptlr &ln of such lip may be determined as f@ilows: ---_ &n, = 2.8 t ~(;c~/t)s-281 200/F, but not less than 4.8 t A simple lip shall not be used as an edge stiffener for any element a flat-width ratio greater than 60. having

5.2.2.2 Zntevxediate stiffemrs - In order that a Aat compression clement may be considered a multiple stiffened element: it shall be stiffened between webs, or between a web and a stiffened edge, by means of intermediate stiffeners parallel LOthe direction of stress, and the moment of inertia of each such intermediate stiflener shall be not less than twice the minimum allowable moment of inertia specified for edge stiffeners in 5.2.2.1 where w is the The following limitations shall also apply: , width of the sub-element. a) If the spacing of stiffeners between two webs is such that the flatwidth ratio of the sub-element between stiffeners is larger than (w/t)lim in 5.21, only two intermediate stiffeners (those nearest each web) shall be considered efTective. If the spacing of stiffeners between a web and an edge stiffener is such that the flat-width ratio of the sub-element between stiffeners is larger than (w/t)Iim in 5.2.1, only one intermediate stiffener shall be considered effective. If intermediate stiff&ers are spaced so closely that the flat-width ratio between stiffeners does not exceed (w/t)iim in 5.2.3, all the stiffeners may be considered effective. Only for the purposes of computing the flat-width ratio of the entire multiple-stiffened 8

b)

c)

element, such clement shall be without intermediate stiffeners between webs or from web to thickness ts is determined as ts = where I, = moment of inc:-tia element, including centroidai axis.

considered as replaced by an element whose width ZQ is the W!JO~ xvidt!l edge stiffener, and whose equiva!et;r follows: -__ 312 I, d .-ws

of the f1111area of the m-uitil)lc-stiEcncd tne intermediate stiffeners, about iis own

5.2.3 Maximm Allewaiilc Oaerall Flat-Width Ratios - Maxinulm alio~vable overall flat-width ratios ZU// disregarding intermediate stitfeners and taking t as the actual thickness of the element. shall be as follows: Stiffened compression element having nne longitudinal Ri edge connected to a web or flange element, the other stiffened by: 60 Simple lip 90 Any other kind of stif&ner

bl

Stiffened compression element with both longitudinal edges connected to other stiffened elements comuression element

c) Unstiffened

500 6i

NOTE Unstiffencd compression elements that have flat-width ratios exceeding approximately 30 and stiflened compression elements that have fi:at-width ratios exceeding approximately 250 are likely to develop noticeable dctormation at the full allowable working stresses, without affecting the ability of the mcmb~r to carry design loads. Stiflezed elements having flat-width ra:ios larger than 500 may be used nith safety to support loads. but substantial deformation of such elements under load may occx and may render inapplicable the design formulae given in this code.

cl;

Lkusually wide jlazges --- Where a flange of a 9~xur.d member ii unusua!iy wide and it is desired to limit :he maximtrn amount of curling or movement of the flange towards the neutral asis, the following formula applies to compression and tension flanges, either stiffened or unstiffened:

where zur = the width of flange projecting beyond the weI>, or haif of the distance between webs for box- or U-type beams; flange thickness; depth of beam; the amount of curling*; and

t=
d= Cf =

*lhe amount of curling that can be tolerated will vary with different kinds of sections and shall be estab!ished by the designer. Amount of curling in the order to 5 percent of ths depth of the section is usually nat considered rxcessive.

IS : sol- 1975 fa,, = the average stress in the full, unreduced flange-width in kgfl ems *(where members are designed by the effective design width procedure, the average stress equals the maximum stress multiplied by the ratio of the effective design width to the actual width).

5.2.4 Maximum Allowable Web Depth - The ratio h/t of the webs of flexural mcmbcrs shah not exceed the foilowing limitations: a) For members with unstiffened webs: (h/t)Mlrr = 150 b) For members which are provided with adequate means of transmitting concentrated loads or reactions or both into the web: (h/t)Max = 200 where h = clear distance between Ranges measured along the plane of web, and t = web thickness. Where a web consists of two or more sheets, the h/t ratio shall be computed for individual sheets. 5.25 Unusually Short Spans Supporting Concentrated Loads - Where the span of the beam is less than 30 wt (wr as defined below) and it carries one concentrated load or several loads spaced farther apart than 2 wi, the effective design width of any flange, whether in tension or compression, shall be limited to as given in Table 1.
TABLE 1 MAXIMUM ALLOWABLE RATIO OF m DESIGN WIDTH TO ACTUAL WIDTH L/WI (1) 30 25 20 18 16 I, RATIO (2) 140 0.96 0.91 0.89 0.86

L/w,
(1) 14 12 10 8 6

RATIO (2) 0.82 0.78 0.73 0.67 0.55

full span for simple spans; or the distance between inflection points for continuous beams; or twice the length of cantilever beams in cm. ZQ = width of flange projection beyond the web for I-beam and similar sections or half the distance between webs of box- or U-type sections in cm.

5.2.5.1 For flanges of I-beams and similar sections stiffened by lips at the outer edges, wl shall be taken as the sum of the flange projection beyond the web plus the depth of the lip.

10

IS : Sol- 1975 6. ALLOWABLE 6.0 General DESIGN STRESS

allowable stresses to be used in design shall

The maximum be as given in 6.1 to 6.8.

6.1 Basic Design Stress - Stress on the net section of ttmion members, and tension and compression on the extreme fibres of flexural membersshall not exceed the value F specified below, except as otherwise specifically provided herein: F = OXiQ F, where Fy is the specified minimum yield point. When the increase in steel strength resulting from cold work of forming is utilized in accordance with 6.1.1, the basic design stress shall be determined as follows: F == 0.60 Fla where F,.,, is the average yield point <the full section. Values of the basic allowable design stress F as defined above for some of the grades covered in IS : 1079-1973* are given in Table 2.
TABLE 2 BASIC ALLOWABLE STRENGTH DESIGN STRESS F F

MINIMUMYlrrm 21 21 30 3G

kgf/mm2

kgf/cm
1 250 1 450 1800 2 16Q

6.1.1 Utilizntion uf Cold Work of Forming - Allowable stresses shall be based upon the specified minimum properties of the unformed steel. Utilization, for design purposes, of any increase in steel strength that results frorr a cold-forming operation is permissible provided that the methods and limitations prescribed in 6.1.1.1 are observed and satisfied.
6.1.1.1 Methods and limitations shall be on the following basis: a) The Utilization of cold work of formin!

point of axially loaded compression mqmbers whe the flanges of flexural members whose proportions ar such that when treated as compression members the quantity 1 (see 6.6.1.1) is unity, shill be determined on the basis of eithr (1) full section tensile tests [see 9.3.1(a)], or (2) stub column tes [see 9.3.1(b)], or (3) computed as follows:

Q=l,and

yield

F,,=

C Fyc +(l -C)Fy,

*Specification for hot rolled carbon steel sheet and strip (third revision).

11

IS

881-1975
where

F,.

C=

average tensile yield point of the full section of compression members, or full flange sections of fiexural members; ratio of the total corner area to the total cross-sectional area of the full section of compression members, or full flange sections of flexural members; tensile yield point of corners, B, F,/(R/t)m. The formula does not apply where Fu/Fy is less than 1.2, R/t exceeds 7, and/or maximum included angle exceeds 120;

Fyc =

Fn =

weighted average tensile yield point of the flat portions established in accordance with 9.3.2 or virgin yield point if tests are not made; & = 3.69 (&IFy) - 0.8;9 (F,/F,)* - 1.79; - 0,192 (F,/F,) - 0468; Rms inside bend radius; F, = tensile yield point of virgin steel* specified in 2.1 or established in accordance with 9.3.3; and F,, = ultimate tensile strength of virgin steel specified in 2.1 or established in accordance with 9.3.3.

b)

The yield point of axially loaded compression members withQ less than unity, and the flanges of fiexural members whose proportions are such that when treated as .:ompression members the quantity Q (see 6.6.1.1) is less than unity, may be taken a.s (1) the tensile yield point of thevirginsteel* specified in IS : 1079-1973t, or (2) the tensile yield point of the virgin steel established in accordance with 9.3.3, or (3) the weighted avera.ge tensile yield point of flats established in accordance with 9.3.2. c) The yield point of axially loaded tension members shall be determined by either method (1) or method (3) prescribed in (a) above. d) Application of the provisiOns of 6.1.1.1(a) shall be confined to the following: 1) Basic Design Stress (6.1), 2) Compression on Unstiffened Elements (6.2), 3) Laterally Unbraced Beams (6.3), 4) Axially Loaded Compression Members (6.6), 5) Combined Axial and Ben$~m~;;sses. (6.7), 6) Cylindrical Tubular m Compression or Bending (6.8), and 7) Wall Studs (8.1).

*Virgin steel refers to the condition (that is coiled or straight) of the steel prior to the cold-forming operation. tSpccification for hot rolled carbon steel sheet and strip (thirdreuirion). 12

IS : 801- 1975 Application of all provisions of the code may be based upon the properties of the flat steel before forming or on 6.1.1 J(b) or (c) as applicable. The effect on mechanical properties of any welding that is to bc applied to the member shall be determined on the basis of tests of full section specimens containing within the gauge length such welding as the manufacturer intends to use. Any necessary allowance for such effect shall be made in the structural use of the member.

e)

6.1.2 Wind, Earthquake, and Cimbined Forces 6.1.2.1 Wind or earthquake only - Members and assemblies subject only to stresses produced by wind or earthquake forces may. be proportioned for stresses 33i percent greater than those specified for dead and live load stresses. A corresponding increase may be applied to the allowable stresses in connections and details. 6.1.2.2 Combined forces - Members and assemblies subject to stress produced by a combination of wind or earthquake and other loads may be proportioned for unit stress 333 percent greater than those specified for dead and live load stresses, provided the section thus required is not less than that required for the combination of dead load and live load. For primary and secondary members of roof assemblies and roof deck, the allowable stresses may be increased by 33$ percent for combined stresses due to dead load, gravity live load (if any) and ponding, provided the section thus required is not less than that required for the combination of dead load and live load. Corresponding increases may be applied to the allowable unit stresses in connections and details. 6.2 Compression on Unstiffened kgf/ cm2 on flat unstiffened elements: a) For w/t not greater than 530/&$ Elements Compression Fc in

F, = 0.60 r;, b) For w/t ratio greater than 530/4z I;c = Fy rO.767 c) For w/t ratio greater but not greater than 1 21 O/~/F,* :

(3.15/104) (w/l)z/~&-j but not greater than 25*:

than 1 210/,/FY

Fc = 562 000/(w/tj2
*When 530/,& the yield and 25: point of steel is less than 2 320 kgf/cm* then for w/t ratios between

Ist

8ol-1975 cl) For wit ratio from 25 to 60*: For angle struts:

Fc = 562 OOO/(w/t)s

For all other sections:

Fc = I 390-

20 w/t ratio as defined in 3.

1x1 the above formulae,

w/t is the flat-width

6.3 Laterally Unbraced Beams -To prevent lateral buckling, the maximum co!npression stress Ft, on extreme fibres of laterally unsupported straight flexural memherst shall not exceed the allowable stress as specified in 6.1 or 6.2 nor the following maximum stresses: a) When bending is about the centroidal axis perpendicular to the web for either I-shaped sections symmetrical about an axis in the plane of the web or symmetrical channel-shaped sections: when ---n I,,

L2 s,,

is greater

than

0.36 rr2 E
FY

C,,

but less than 18 y

Y

cb

Fb=fFY-

5.4;;;~

when

L2 sx,is equal ,to or greater than d &c

I;r, = 0.6 r2 E c, m b)

1.8n2Ecb

FY

d&c,
sections C,, bent about the centroidal but less than ? z E cb
Y

For point-symmetrical Z-shaped axis perpendicular to the web: is greater than

G.!89E --_._.-f;Y

when *
YC

is equal to or greater ti Ectiiz

than .

ry
Y

FI, =0.3

d&c

*Uns:ifTened compression eiements having ratios of rqt exceeding approximately 30 may show notiLeab!e distortion of the free edges uncier allowable compressive stress without detriFor ratios of w/t exceeding approximcnt to the ability of the member to support load. mately 60 distortion of the flanges is iikeiy to be SO pronouncrd as to render the section structurally undesirable unless load and stress are limited to such a degree as to render such use uneconomical. tI2.e provisions of this Section apply to I-, Z-, or channel-shaprd flexural members (not including nnritiplc-web deck, U-and closed-box type members and curved or arch members). The pro:Gsior:s of this Section do not apply to laterally unbraced compression flanges of otherwise h~rerally stable sections.

14

IS : solwhcrc L== the unbraced length of the member;

1975

I,, = the moment of inertia of the compression portion of a section about the gravity axis of the entire section parallel to the web; s,, = Compression section modulus of entire seclion about major axis, Ix divided by distance to extreme compression fibre; Gb = bending coefficient which can conservatively be taken as unity, or calculated from: Ct, = 1.75 + 1*05(z) + 0.3 ($):but not morethan2.3.

Where Ml is the smaller and MI the larger bending moment at the ends of the unbraced length, taken about the strong axis of the members, and where MI/MS, the ratio of end moments is positive when MI and M, have the same sign (reverse curvature bending) and negative when they are of opposite sign (single curvature bending). When the bending moment at any point within an unbraced length is larger than that at both ends of this length, the ratio Ml/MS shall be,taken as unity. For members subject to combined axial and bending S~RSS (sue6.7), Ct,, shall be 1. E = d = 6.4
AlIowalle

modulus of elasticity = 2 074 000 kgf/cm*; and depth of section. Stresses in Web of Beams in

6.4.1 Shcor Stresses in Webs -The maximum average shear stress F,, kgf/cm, on the gross area of a flat web shall not exceed: a) For h/t not greater than 4 590/1/T F Y

_1275dG with a maximum of 0.40 Fy h/t b) For h/t greater than 4 59O/dFT F = - 5 850 000 (h/t)

where t = web thickness, A = clear distance between flanges measured along the plane of web, and F, = yield point in kgf/cma. 15

IS : 801~ 1975 ILherc the web consists of two or more sheets these shall be consider-cd as separate members carrying their share of the shear. 6.4.2 Bending Stress in Ltkhs - The compressive stress Fb,., in kgf/cm2, in the Aat web of a beam due to bending in its plane, shall not exceed F nor shall it cxcerd: FbW = 36 560 000 (h/Q2 kgf/cms

6.4.3 Combined Bending and Shear Stresses in Webs - For webs subject to both bending and shcar stresses, the member shall be so proportioned that such stresses do not exceed the allowable values specified in 6.4.1 and 6.4.2 and that the quantity where
fbw =I

2/(fhW/FbW) + (f;/FVJ2 does not exceed unity: stress at junction of flange and web;

actual

compression

36 560 000 FhW == I___ kgf/cms;

. (h/l)2

..fv = actual average shear stress, that is, shear force per web divided
F, = bv webs area; and allowable shear stress as specified of 04 Fy shall not apply. in 6.4.1 except that the limit

6.5 Web Crippling of Beams - To avoid crippling of unreinforced beam webs having a flat-width ratio h/t equal to or less than 150, concentrated loads and reactions shall not exceed the values of PM&~ given below. Webs of beams for which the ratio h/t is greater than 150 shall be provided with adequate means of transmitting concentrated loads and reactions directly into the web. a) Beams having single unreir$orced webs:

(1) For

end reactions or for concentrated loads on outer ends of cantilevers: For inside corner radius equal to or less than the thickness of sheet: P ~~~ = 70 12 [98 + 4,20(,X/t) - 0.022 (A-/t) (h/k) - 0,011 (h/t)] x [I.33 - 0.33 (F,/2 320)-j (Fyi2 320) f;or other corner radii up to 4 t, the value ~~~~ given by the above formula shall be multiplied by (I.15 -0.15 R/t).

(2) For

reactions of interior supports or for concentrated loads located anywhere on the span: For inside corner radius equal to or less than the thickness of sheet: Phiax = 70 t2 [305 + 2.30 (X/tj 0.009 (,Llt) - 0.5 (h/t)] (h/t) x [I.22 - 0.22 (Fyi2 320)] iFy/2 320) 16

IS : 801-

1975

For other corner radii up to 4 t, the value Pwax given by the above formula is to be multiplied ,by (1.06 - 0.06 R/L). (3) For corner radii larger than 4 t, tests shall be made in accordance with 9. b)
For I-beams made of two channels connected back to back 07 fo7 similar sections which provide a high degree of restraint against rotation of the web, such as I-sections made by welding two angles to a channel:

(1) For end reactions or for concentrated of cantilevers:

PMsX = t2 F, (4.44 (2) For

loads on the outer ends

+ 0.558d.N/t) loads

reactions of interior supports or for concentrated located anywhere on the span:

PMvlax t2 F, (6.66 + =

ll46m)

In all of the above, PM*~ represents the load or reaction for one solid web sheet connecting top and bottom flanges. For webs consisting of two or more such sheets, ~~~~ shall be computed for each individual sheet and the results added to obtain the allowable load or reaction for the composite web. For loads located close to ends of beams, provisions of 6.5(a) (2) and (bj (2) apply, provided that for cantilevers the distance from the free end to the nearest edge of bearing, and for a load close to an end support the clear distance from edge of end bearing to,nearest edge of load bearing is larger Otherwise provisions of6.5(a) (1). and (b) (2) apply. than 1.5h. In the above formulae, allowable concentrated load or reactions ; ~MMSX = t = web thickness ; _V = actual length of bearing, except that in the above formulae .the value of Nshall not be taken greater than h; h = clear distance between flanges measured along the plane of web ; FY = yield point; and R = inside bend radius. 6.6
Axially 6.6.1 Loaded Compression Members

Stress Shapes not subject to torsional-Jlexural buckling

6.6.1.1

(a)

For doubly-symmetric shapes, closed cross-sectional shapes or cylindrical sections, and any other shapes which can be shown not to be subject to torsional-flexural buckling, and for members braced against twisting, the average axial stress P/A, in compression members shall not exceed the following values of 17

IS : S01 - M7~

F*I except as otherwise

permitted

by 6.6.l.l(b)

K Lfr less than

cc
%2

&=23 Q&-=

12

05!22 QF,

3( QFy)2 A-L ~ 23 nz E () QFV K~r ( i2 500 )

K L/r equal to or greater than 12 #E F.l = 23 (K J!+}z 10680000

<Q

=
WI; e VT G

(K

[./r)

= ~2 nz E/F,; P == total load; .4 = fidl tmreduced cxoss-sectional area of the member; Fal := allowable average compression stress under concentric hwling; E =:: modulus of elasticity = 2074000 kgf/cm2; K = Hective length factor*; L =. unbraced length of member; radius of gyration of full, unreduced cross section; F: ~ yieid point of steel; and

Q=

a factor

determined

as follows:

(1) For members composed entirely of stifEened elements, Q is the ratio between the effective design area, as determined from the effective design widths of such elements, and the full or gross area of the cross section. The effective design area used in determining $Qe~i~6*msed upon the basic design stress F as entirely of unstifleneti elecomposed (2) For membem ments, Q.isthe ratio between the allowable compression stress Fe for the weaktstelement of the cross section (the clement having the largest flat-width ratio) and
q IK1frames where lateral stabiIity is provided by diagonal bracing, shear w@, attachment to an ad.;accnt structure having adequate lateral stability, or by floor slabs or roof decks secured horizon WILY by walls or bracing sysmrns paraUel to the plme of the fiamc, a .d in trusses the effcctire length factor K for the compression members shall be taken as unity, unless analysis shows that a smaller value may bc used. The effective knt@ KL of comprcs~ion mernbem, in a fkaxne which depen& upon its own bending stifhws for lateral yt.ati]li y, shall be determined by a ratiovtal method and shall not be less than the actual t t~ nbraced length,

18

IS : 861-

1975

the basic design stress, F, where F, is defined in 6.2 and F is as defined in 6.1. (3) For members composed of both stiffened and unstiffened elements the factor Q is the product of a stress factor QB computed as outlined in (2) above and an area factor Q8 computed as outlined in (1) above, except that the stress upon which Qa is to be based shall be that value of the stress FB which is used in computing Q,, and the effective area to be used in computing (La shall include the full area of all unstiffened elements. b) When the factor Qis equal to unity, the steel is 2.29 more in thickness and K L/Tis less than Cc: (KL/r)z -2(c,)2 Far = 5 3 (K L/r) L---.p - -1 3 8 (Cc) 1 mm or

FY

(X L/r)3 8 (Cc)3

6.6.1.2 Singly-symmetric and nonsymmetric shapes of open cross section or intermittently fastened singly-symmetrical combonents of built-up shakes having Q= 1 .O whick may be subject to torsionalfi?xural buckling - For singly-symmetric or nonsymmetric shapes of open cross section or intermittently fastened singlysymmetrical components of built-up shapes having Q=l .O which may be subject to torsional-flexural buckling and which are not. braced against twisting, the average axial stress P/A shall not exceed Fal specified in 6.6.1.1 or F,, given below: For UTro70.5 Fp: F,, = 0522 For orro90.5 F,: Faa = 0.522 uTFo F,.Fy2 7.67 UTFO

where Fas = allowable average compression stress under concentric loading, and UTF(-J = elastic torsional-flexural buckling stress under concentric loading which shall be determined as follows: a) Singly-symmetric shapes - For members whose cross sections have one axis of symmetry (x-axis), 0~~0 is less than both ueX and ut and is equal to: 1 UTFO = r8 (ex + t) d(Uex + Ut)2 4/3Jex Jt

19

IS : 801-

1975 where sex = (X $:)z

B = 1 - h!~lJ2,
A = cross-sectional Y0 =
I

area, of cross

Z/Y,2 + $2 -+ X02 = poiar radius of gyration section about the shear centre,

x, rY = radii of gyration of cross section about centroidal principal axes, E = modulus of elasticity = 2 074 000 kgf/cm*, G = shear modulus = 795 000 kgf/cm2, X = effective length factor, L = unbraced length of compression member, x0 = distance from shear centre to centroid along principal x-axis,

the

3 =

St Vcnant torsion constant of the cross section, cm4. For thin walled sections composed of n segments of uniform thickness,

3 =
C, b)

(l/3) (&3

+ 12t23 +

. . . . . . + l&.
i, and

. . . + l&3),
i,

ti T= strel thickness
11 = length L- warping

of the member

for segment

of middle constant

line of segment

of torsion of the cross section.

Nonsymmetric shapes - Shapes whose cross sections do not have any symmetry, either about an axis or about a point, 0~~0 shall be determined by rational analysis. Alternatively, compression members composed of such shapes may be tested in accordance with 9.

6.6.1.3 Singly-symmetric or nonsymmetric shapes or intermittently fastened sing+symmetricaZ components of built-up shapes having Q< I.0 which are subject to torsional-Jexural buckling - Compression members composed of singlyshapes or intermittently fastened singlysymmetric, or nonsymmetric symmetrical components of built-up shapes having Q< 1 .O which are subject to torsional-flexural buckling and which are not braced against twisting can be conservatively proportioned by replacing F, by QFY in 6.6.1.2 or their strength may be determined by tests in accordance with 9. Qis defined in 6.6.1.1. 6.6.2 Bracing and Secondary loaded bracing and secondary
not depend.

Members members*,

On the cross section of axially when L/r ratio exceeds 120, the

*A secondary member is one upon which the integrity of the structure as a whole does
For this case, X is taken as unity.

20

IS : 891allowable compression mined as follows: stress under concentric F,,B = F. 1.3 *&r F.

1975

loading I;Bs shall be deter-

In the above formula, the maximtim stress by 6.6.1.1 or 6.6.1.2 whichever is applicable.

shall be determined

6.6.3 Maximum SIrnderness Ratio - The slenderness ratio he L/r of compression members shall not exceed 200, except that during construction only, K L/r shall not exceed 300. 6.7 Combisud Arirl and Bending Stresses

6.7.1 Doubly-Symmetric Shapes ok Shapes .Not Subject to 7orsional or TorsionalFlexural Buckling - When subject to both axial compression and bending, doubly-symmetric shapes or shapes which are not subject to torsional or torsional-flexural buckling shall be proportioned to meet the following requirements:

<l.O when 6 &I < 0.15, the following formula may be used in lieu of the above two formulae:

The subscripts x and y in the above formulae indicate the axis of bending about which a particular stress or design property applies. 6.7.2 Singly-Symmetric Shafis or Intermittently Fastened Singly-Symmetric Components of Built-Up Shapes Having Q - I.0 Whtch May Be Su!@ct to Tor.rionalFlexural Buckling -- Singly-symmetric shapes subject to both axial compression and.bending a plied in the plane of symmetry shall be proportioned to meet the following P our requirements as applicable: a>

21

IS : sol- 1975 when

fa & 0.15, the following formula may be used in lieu of the F

al above two formulae:

b) If the point of application of the eccentric load is located on the side of the centroid opposite from that of the shear centre, that is, if c is positive, then the average compression stress f. shall also not exceed Fa given below: For qr >0.5 Fy: r;, = 0.522 Fy For 0~~40.5 where on shall be determined according to the formula: = 1.0 F,.: F. = O-522 (J-~,T F2 767 Vr-,T

c) Except for T-or unsymmetric I-sections, if the point of application of the eccentric load is between the shear centre and the centroid, that is, if e is negative, and ii Fnr is larger than F,,, then the average compression stress fs shall also not exceed F. given below: Fa = Far + -&
(FOE Fa;,,)

d) For T- and unsymmetric I-sections with negative eccentricities: 1) If the point of application of the eccentric load is between the shear centre and the centroid, and if F,, is larger than Faa, then the average compression stress f. shall also not exceed F, given below: Fa = ha + 2)

-$

Pao- Fa,)

If the point of application of the eccentric load is located on the Gde of the shear centre opposite from that of the centroid, then the average compression stress f. shall also not exceed F,, given below: W nrr >0.5 F,, Fa = 0.522 Fy - 7.67 UTF 0~~0.5 F,, F. =. 0.522 OTF 22

ls

891-1975

shall be determined

according

to the formula:

In 6.7.2, x and y are centroidal axes and the x-axis is the axis of syrnmetry whose positive direction is pointed away from the shear centre. In 6.7: c, = a coefficient a) b) whose value shall be taken as follows: to joint translaFor compression members in frames subject tion (sideway) C, = 0.85.

For restrained compression members in frames braced against joint translation and not subject to transverse loading between their supports in the plane of bending cm = 0% where 0.4 2, 2 but not less than 0.4

2 is the ratio of the smaller to larger moments Ms at *the ends of that portion of the memt _, unbraced in the plane of bending under consideration. M is positive when the member is bent in reverse M, curvature and negative when it is bent in single curvature.

c)

For compression members in frames braced against joint translation it the plane of loading and subject to transverse loading between their supports, the value of C, may be determined by rational analysis. However, in lieu of such analysis, the following values may be used : ( 1) for members whose ends are restrained, C, = 0.85, and (2) for members whose ends are unrestrained, C, = 1 .O. whose value shall be taken as follows: For compression members in frames subject to joint translation (sideway) CTF = 0.85. For restrained compression members in frames braced against joint translation and not subject to transverse loading between their supports in the plane of bending C,, where -1 Ms = 0.6 0.4 2 f to larger moments

Cm

a coefficient a) b)

is the ratio of the smalier 23

l!s : 801- 1975

at the end of that portion of the members, in the plane of bending under consideration. MI is positive when the member K curvature and negative when it curvature.
G=

unbraced in reverse in single

is bent is bent

distance from the centroidal compression stress, negative centre side of the centroid depth of section

Uris to the hbre with maximum when the fibre is on the shear

d=
d=

Fa

eccentricity of axial load with respect to the centroidal r?xis, negative when on the shear centre side of the centroid maximum average compression stress average allowable compression stress determined by both requirements 6.7.2(a) and 6.7.2(d)(2) if the point of application of the eccentric load is at the shear centre, that is, the calculated values off, and FS for c = x0 average allowable compression stress determined by requirements 6.7.2(a) if the point of application of the eccentric load is at the shear centre, that is, the calculated value off, for e = x0 allowable compression stress under concentric loading determined by 6.6.1.1 for L = 0 allowable compression stress under concentric loading according to 6.6.1.1 for buckling in the plane of symmetry allowable compression stress under concentric loading from 6.6.1.2 maximum bending stress in compression that is permitted by this code where bending stress only exists (SIC6.1, 6.2 and 6.3) maximum bending stress in compression permitted by this code where bending stress only exists and the possibility of lateral buckling is excluded (J& 6.1 and 6.2)
127raE (mayb e increased one-third in accordance with 23 (K Lb/rb) 6.1.2) axial stress = axial load divided by full cross-sectional area of member P/A maximum bending stress = bending moment divided by appropriate section modulus of member M/S, noting that for members having stiffened compression elements the section modulus shall be based upon the effective design widths of such elements

F ac =

FSE

F a0

Fa, = Fa, =
Fb

Fbl =
F)e =

fa =
fb =

24

1s : sol- 1975
lxC = II = moment of inertia of the about its axis of symmetry moment of inertia compression about portion they-axis of a section

of the section

= &

2%dA + py dA Y

where x is the axis of symmetry h- =

_ xg
and y is orthogonal to x

Lb = MC = MT =
r,, =

effective length factor in the plane of bending actual unbraccd length in the plane of bending ing compression ing tension

-Auex [j + vj2 +

(0 tl uex)] = elastic critical moment causon the shear centrc side of the centroid
centre

yo2

-Au,,

[j - dj + r,,2(q/a,,)]
on the shear

= elastic critical moment side of the centroid

caus-

rxc =

radius of gyration about axis of bending radius of gyratio.1 about the centroidal axis parallel to the web of that portion of the I-section which is in compression when there is no axial load section modulus of entire section about axis normal to axis of symmetry, I,/distance to extreme compression fibre of the shear centre, negative bending stress caused by MC by Mcc -

SYC= compression
x0 =

x coordinate

UbC

For I-sections

1,

maximum

compression

with unequal

flanges UJbe may be approximated

n2.Ed I,c L2 SW
UbT =

MT c -r ZY
yr2 Ed I,.

maximum

compression

bending

stress caused

by A& by

For I-sections

with unequal

flanges 0b.r may be approximated

L2 SW
e---c Jbl = UTF 2
TY

maximum by llrr

compression

bending

stress

in

the

section
ub2 =

caused

m-7
v2

x0 c
TY

ae

(fiCJm =

Lb/rb)

average elastic torsional-flexural buckling stress, that is, axial load at which torsional-flexural buckling occurs dividr.3. by the full cross-sectional area of member 25

IS t

sol-1975

0, rr, uex, ut, UTFO are as defined in 6.6.1.2. 6.7.3 Singly-Symmetric Sha@es or Intermittently Fastened Singly-Symmetric Cornfmnents of Built- Up Shapes HaGng Q< 1.0 Which May Be Subject to TorsionalFlexural Buckling - If Q< 1.O singly-symmetric shapes or intermittently fastened singly-symmetric components of built-up shapes subject to both axial compression and bending applied in the plane of symmetry can be conservatively proportioned by replacing FY by QFY in 6.7.2, or their strength may be determined by tests in accordance with 9. Q is defined in 6.6.1.1.

4 4

6.7.4 Sing&Symmetric Shapes Which Are Nonsymmetrically Loa&d - Singlysymmetric shapes subject to both axial compression and bending applied out of the plane of symmetry shall be designed according to 9.2. 6.8 Cylindrical Tubular Members in Compression or Bcndfng For cylindrical tubular members with a rati? D/t of mean diameter to wall thickness not greater than 232 000/F,, the compression stress shall not exceed the basic design stress F. For cylindrical tubular members with a ratio D/t of mean diameter to wall thickness larger than 232 000/F, but not greater than 914 000/F, the compression stress shall not exceed F r = 46 540 olt + 0.399 F>

For compression members the allowable stress P/A under axial load shall also not exceed F81 as prescribed by 6.6.1.1 for Q = 1. 7. coNNEcTXoNs 7.1 General - Connections shall be designed to transmit the maximum stress in the connected member with proper regard ior eccentricity. In the case of members subject to reversal of stress, except if caused by wind or earthquake loads, the connection shall be proportioned for the sum of the stresses. 7.2 Welds 7.2.1 Fusion We&is - Fusion welds shall be proportioned so that stresses therein do not exceed the following values: SpeciJied Minimum Yield Point of Lowest Strength Steel Being Joined kgf/cms Q 2 500 > 2 500 but 93 500 > 3 500 26 Permissible Stress* in Shear on Throat of Fillet or Plug Welds kgf/cma 955 1 100 1 250

Is :

801-197s

The allowable stress in tension or compression on butt welds shall be the same as prescribed for the lower grade of the base metals being joined, provided the welds are of full penetration type and the yield strength of the filler metal is equal to or greater than the yield strength of the base metal. Stresses due to eccentricity of loading, If any, shall be combined with the primary stresses, and the combined stresses shall not exceed the values given above. Stresses in a fillet weld shall be considered as shear on the throat for any direction of the applied stress. Neither plug nor slot welds shall be assigned any value in resistance to any stresses other than shear. 7.2.2 Resistance Welds -In sheets joined shear per spot shall be as follows: Thickness of Thinnest Outside Sheet (1) mm 0.25 0.50 0.80 1 .oo 1.25 1.60 Allowable Shear Strength per spot (2) kg 23 1:: 159 239 330 by spot welding the allowable Allowable Shear Strength per spot (2) kg 489 625 750 909 1 818

Thickness of Thinnest Outside Sheet (1) mm 2.00 2.50 2.80 3.15 5.00

NOTE - The above values are based upon A WS C- 1.1-66 Recommended practices for resistance welGng, issued by the American Welding Society, and apply to pulsation welding as well as spot welding. They are applicable for all structural grades of low carbon steel, and are based on a factor of safety of approxtmately 2.5 applied to selected values from AWS C-1.1-66 Tables 1.1 and 1.3. Values for in.ermediate thicknesses may be obtained by straight line interpolation. The above values may also be applied to medium carbon and low alloy steels. Spot welds in such steels give somewhat higher s&ear strengths than those upon which the above values are based, however, they may require special welding conditions. In all cases welding shall be performed in accordance with IS : 819-1957*.

7.3 Connecting Two Cliannels to Form an I-Section - The maximum permissible longitudinal spacing of welds or other connectors, &fax joining two channels to form an f-section shall be: a) For Compression Members: Y L Max = where L
*Code or practice

L rev 2 r1

unbraced

length

of compression

members;

for resistance spot welding for light assemblies in mild steel.

27

ls

: 801- 1975
r CI = Yl = radius of gyration of one channel axis parallel to web; and about its centroidal

radius of gyration of I-section about the axis perpendi&lar to the direction in which buckling would occur for the given conditions of end support and intermediate bracing, if any. I,) For Flexural Members: Sax = L/6 In no case shall the spacing exceed the value

\vllcrc

LS
g

span of beam; vertical distance between the two rows of connections near or at top and bottom flanges; of connection in tension; distance of shear centre of channei from mid-plaue of the web, for sin,ple channels :\.ithout stiffening lips at the outer edges, m=

Ts = strength
m =

WI2
2 wi f d/3

; and
(see 7.3.1). lips at the outer edges, ( dS)]

== intensity of load on beam For C-shaped channels with stiffening

m= where wr =

wl

dt xC

wldf2d,

projection of flatrges from inside face ol web (for channels with flanges of unequal Lvidth, or shall be taken as the width of the wider flangej; depth of channel overall depth or beam; and about its centroidal of lip;

d= dI = z, =

moment of inertia of one channel axis normal to the web.

7.3.1 The intensity of load Q is obtained by dividing the magnitude of For beams designconcentsateii ioads or reactions by the length of bearing. ed for a uniformly distributed load, the intensity q shall be taken equal If tL three times the intensity of the uniformly distributed design load. the length of bearing of a concentrated load or reaction is smaller than the weld spacing, s, the required strength of the welds or connections closest to the load or reaction P, is Pm/2 g

7-S =

28

IS : 801- 1975 7.3.2 The required limited spacing of connections &t&, depends upon the Therefore, if uniform intensity of the load directly at the connection. spacing of connections is used over the whole length of the beam, it shall hc In cases where determined at the point of maximum local load intensity. this procedure would result in uneconomically close spacing either cf the following methods may be adopted: a) b) The connection to the variation spacing may be varied along of the load intensity; or the beam according

Reinforcing cover plates may be welded to the flanges at points The strength in shear of the where concentrated loads occur. connections joining these plates to the flanges shall then be used for TS and g shall represent the depth of the beam.. Elements -. Thr spacing connecting a compression or other element shall not

7.4 Spacing of Connections in Compression s in line of stress of welds, rivets, or bolts cover plate or sheet to a non-integral stiflener exceed: a)

that which is required to transmit the shear between the connected parts on the basis of the design strength per connection specified in 7.2; nor 1 680 t/d w h ere t is thickness of cover design stress in cover plate or sheet; nor plate or sheet, and f is

b) c)

three times the flat width w of the narrowest unstiffened compression element in that portion of the cover plate or sheet which is tributary to the connections, but need not be less than 1 590 t/.d/r;, if the value of Fc permitted in the unstiffened element is grtater than 0.54 FY or 1910 t/dFy if the value of Fc permitted in the unstiffened element is 0.54 Fy or less, unless (b) above. closer spacing is required under (a) cr

In the case of intermittent fillet welds parallel to the direction of stress the spacing shall be taken as the clear distance between welds plus 13 mm. In all other cases the spacing shall be tabn as centre to centre distance between connections.

Excepion:

The requiremel n* of this clause do not apply to cover sheets which act only as sheathing.material and are not considered as load carrying elements. govern bolted

7.5 Bolted Connections - The following requirements connections of cold formed steel structural members.

7.5.1 Minimum Spacing and Edge Distance in Line of Stress - The clear di&ance between bolts which are arranged in rows parallel to the direction of force, also the distance from the centre of any bolt to that end or other boundary of the connecting member tcnciards which the pressure of the bolt 29

Is i

801-1975
shall not be less than 1.5 d nor less than P/(0.6 F,. t) d .= P = t = F, = diameter force thickness of bolt, by bolt, connected sheet, and of thinnest where transmitted

is directed

yield point.

?.5.2 Tension Stress on .Net Section - The tension stress on the net section of a bolted connection shall not exceed 0.6 FY nor shall it exceed: where r= (1.9 0.9 r + 3 rd/s) 0.6 F,

the force transmitted by the bolt or bolts at the section considered, divided by the tension force in the member at that section. If r is less than 0.2, it may be taken equal to zero ; to lint of stress. In the case to the width of sheet; and The bearing stress on the area area

spacing of bolts perpendicular of a single bolt, s is equal d and F, are defined in 7.5.1. 7.5.3 Bearing Stress in Bolted Connections (d x t) shall not exceed 2.1 Fy*.

S=

7.5.4 Shear Stress on Bolts - Shear stress on the gross cross-sectional of bolt, under dead and live load, shall not exceed the following values: Precision and semi-precision bolts Black bolts Steel conforming to property class 4.6 of IS : !367-1967t 8. BRACING 970 kgf/cms 820 kgf/cme 1 060 kgf/cms

REQUIREMENTS

8.0 Structural members and assemblies of cold-formed steel construction shall be adequately braced in accorda.nce with good cnginecring gractice. The following provisions cover certain special cases and conditions.
8.1 Wall Studs - The safe load-carrying capacity of a stud may be computed on the basis that wall material or sheathing (attached to the stud) furnishes adequate lateral support to the stud in the plane of the wall, provided the wall material and its attachments to the stud comply with the following requirements: a) Wall or shea.thing shall be attached to both faces or flanges of the studs being braced; b) The maximum spacing of attachments of wall material to the stud being braced shall not exceed ahfax as determined from the formula:
*If the ratio of tensile strength to yield point is less than 1.35, a stress equal to the specified minimum tensile strength of the material divided by 1.35 shall be used instead ofF, in applying the provisions of 7.5.1, 7.51 and 7.5.3. tTcchnica1 supply conditions for threaded fasteners (first r&ion).

30

IS : 801- 1975

The

slenderness

ratio of the stud betlveen the spacing of

attachment> attachments

air, shall shall not

not exceed

L S . Therefore,

exceed that sp:cified

above nor shall it exceed:

L rz a.vClar F 2 Tl The minimum modulus of elastic support AeW be exerted laterally to by the wall material and its attachment in order to brace the stud, shall not be less than Fy2 a A2 hT, = a E I, The lateral force in kg which each single attachment of the wall material shall be capable of exerting on the stud in the plane of the wall (in order to prevent lateral buckling of the stud) shall not be less than rr, P, L/240
PMln=

*E

I2 KW/a-Ps

In the above formulae: actual spacing of attachments of wall material to stud a= measured along the length of stud (a = 1 for continuous attachment) ; area of cross section of stud; modulus of elasticity = 2 074 000 kgf/cm?; yield point of steel in stud; moment of inertia of cross section of stud about its axis parallel to wall; moment of inertia of cross section of stud about its axis perpendicular to wall; modulus of elastic support of wall material (on each side of stud) and its attachments. This is, K, = P/e wkre P is the force which produces an elongation of e in a strip of wall material of width a and of length equal to the distance between adjacent studs. In paragraphs (b) and (d), &is the modulus actually provided as determined from tests. In paragraph (c), KW is the minimum required for a given spacing of attachments. L= length of stud; P* = design load on stud; rl = radius of gyration of stud about its axis parallel to wall
r2 =

= 1/I,lA; radius of gyration = &a.

of stud about its axis perpendicular

to wall

31

Is

: 801-~1975

8.2 Channel and ZSecdons Used as Beams - The following provisions for the bracing against twist, of channel and Z-sections used as beams apply only when: (a) neither flange is connected to dzck or sheathing material in such a manner as to effectively restrain lateral deflection of the connected flange, and (b) such members are loaded in the plane of the web*. 8.2.1 ~S$ZC~TZ~Braces -Braces of shall be attached both to thr top and bottom flanges of the sections at the ends and at intervals not greater than one-quarter of the span length in such a manner as to prevent tipping at the ends and laterai deflection of either flange in either direction at intermediate braces. If one-third or more of the total load on the beams is concentrated over a length of one-twelfth or less of the span of the beam, an additional brace shall be placed at or near the centre of this 1Gaded length. 8.2.2 Design OJ Braces - Each intermediate brace, at top and bottom flange, shall be designed to resist a lateral force Pi determined as follows: a! For a uniformly loaded beam PI = 1.5 K times the load within a distance 0.5 a each side of the brace. b) For concentrated loads P1 - 1.0 ET times the concentrated Ioad P

within a distance 0.3 a each side of the brace, plus :,I; -

1 -- _; ph+ ( > for each such concentrated load P located farther than 0.3 c but not farther than 1 .O ~1 from the brace. In the above fcbrmulae: For channels: K = m/d e where m -= distance from shear centre to mid-plane of the web, as specified in 7.3; and d = depth of channel.

For Z-sections: K = IxyjIx where ITv = IX For channels x a product of inertia of full section axis parallel and perpendicular -1 moment of inertia of full section axis perpendicular to web. and Z-sections: = distance from concentrated load 1 length of bracing interval. about c.entroidal to web, and about rentroidal

P to brace, and

*When only one Range is connected to a deck or sheathing material to effectively restrain lateral deflection of the connected flange, bracing may or may not be needed to prevent twisting of the member, depending upon the dimensions of the member and span and upon whether the unconnected flange is in compression or tension..

32

IS : 801-

1975

End braces shall be designed for one-half of the above forces. Braces shall be designed to avoid local crippling at the points of attachment to the member.

8.2.3 Allowable Stresses -For channels and Z.,beams intermediately braced according to the requirements of 8.2.1 and 8.2.2 the maximum compression stress sha!l be that specified in 6.3, except that the length of the bracing interval, a, shall be used instead of the length L. in the formulae of 6.3. 8.3 Laterally Unbraced Box Beams - For closed box type sections used as beams subject to bending about the major axis, the ratio of the lateraliy unsupported length to the distance between the webs of the section shall not exceed 175 700/F,, 9. TEST
FOR SPECIAL CASES

9.1 General 9.1.1 Where the composition or configuration of elements, assemblies, or details of cold-formed steel structural members are such that calculation of their safe load-carrying capacity or deflection cannot be made in accordance with 5 to 8 of this code, their structural performance shall be established from tests and evaluated as specified in 9.2. 9.1.2 Tests fat determination of mechanical properties of full sections to be used in 6.1.1.1 shall be made as specified in 9.3.1. 9.13 Tests for determining mechanical properties of flat elements of formed sections and representative mechanical properties of virgin steel to bc used in 6.1.1.1 shall be made in accordance with the provisions of 9.3.2 and 9.3.3. 9.1.4

The provisions of 9 do not apply to light gauge steel diaphragms.

9.1.5 Tests shall be made by an independent testing laboratory or by a manufacturers testing hboratcry. 9.1.6 Tensile testing procedures shall be according to 15 : 1608-1972*. 9.2 Evzhation of Tests for Determining Strnctwal Performance Where tests are necessary for the purposes defined in 9.1.1 they shall be evaluated in accordance with the following procedure?: a) Where practicable, evaluation of test results shall be made on the basis of the mean values resulting from tests of not fewer than three identical specimens, provided the deviation of any individual test result from the mean value obtained from all tests does not exceed IfI percent. If such deviation from the mean exceeds 10 percent *Method for tensile testingof steel products other than sheet, strip, wire and tube. $Ihetat evaluation procedures and load factors specified in 9.2 are not applicable to for the latter, the code provides generally a slrfety factor of 5/S. 33
tests of members and assemblies whose properties can be caiculated accordiq

ti6rmatory to 5 to 8

Is

: 8Ql- 1975 at least three more tests of the same kind shall be made. The average of the three lowest values of all tests made shall then be regarded as the result of the series of tests. b) Determinations of allowable load-carrying capacity shall be made on the basis that the member, assembly, or connection shall be capable of sustaining a total load, including the weight of the test specimen, equal to twice the live load plus one-and-a-half the dead Where the governing design load is due in load without failure. whole or part to wind, earthquake loads, or combined forces, the foregoing load factors shall be reduced by dividing by 14 in accordance with 6.1.2. Furthermore, harmful local distortions which interfere with the proper functioning of the member or assembly or its connections shall not develop during the test at a total load, including the weight of the test specimen, equal to the dead load plus li times the live load. c) In evaluating test results, due consideration shall be given to any differences that may exist between the yield point of steel from which the tested sections are formed and the minimum yield point specified for the steel which the manufacturer intends to use. Consideration shall also be given to any variation or difference which may exist between the design thickness and the thickness of the specimens used in the tests.

9.3 Tests for Determining

of Flat Material

Mechanical

Properties

of Formed

Section

9.3.1 Full Section Tests - These provisions are intended to apply only to the determination of the mechanical properties of full formed sections for They are not to be construed as permitting ;hr: purposes defined in 9.1.2. Tests to the use of test procedures instead of the usual design calculations. determine mechanical properties shall be conducted in accordance with the following: a) For tensile yield point determinations refer to 9.1.6.

b) Compressive yield point determinations shall be made by means of compression tests* of short specimens of the section and shall be taken as the smaller value of either the maximum compressive strength of the section divided by the cross-sectional area or the stress defined by one of the following methods: 1) For sharp yielding steel the yield point shall be determined by the autographic diagram method or by the total strain under load method, 2) For gradual yielding steel the yield point shall be determined by the strain under load method or by the 0.2 percent ofiet method. +sU Appendix A for recommendations regarding details of compression testing. 34

IS : 801-1975
When the total strain under load method is used, there shall be evidence that the yield ioint so determined agrees substantially with the yield point which would be determined by the 0.2 percent offset method. The methods described above shall agree in general with IS : 160%1972*. c) Where the principal effect of the loading to which the member will be subjectecl in service will be to produce bending stresses, the yield fGnt shall be determined for the flanges only. In determining such yield point tests shall be made on specimens cut from the scctioil. Each such specimen shall consist of one ,complete flange plus a portion of the web of such flat-width ratio that the value of Q for the specimen is unity. d) For acceptance and control purposes, two full section tests shall be made from each lot of not more than 50 tonnes nor less than 30 tonnes of each section, or one test from each lot of less than For this purpose a lot may be defined 30 tonnes of each section. as that tonnage of one section that is formed in a single production run of material from one heat or blow. e) At the option of the manufacturer, either tension or compression tests may be used for routine .acceptance and control purposes, provided the manufacturer demonstrates that such tests reliably indicate the yield point of the section when subjected to the kind of stress under which the member is to be used. 9.3.2 Tests of Flat Elements of Formed Sections - The yield point of flats Fvr shall be established by means of a weighted average of the yield points of standard tensile coupons taken longitudinally from the flat portions of a representative cold-formed member. The weighted average shall be the sum of the products of the average yield point for each flat portion times the ratio of the cross-sectional area of that flat portion to the total area of flats in the cross section. The exact number of such coupons will depend on the shape of the member, that is, on the number of flats in the cross section. At least one tensile coupon shall be taken from the middle of each flat. If the actual virgin yield point exceeds the specified minimum yield point, the yield point of the flats FYI shall be adjusted by multiplying the test values by the ratio of the specified minimum yield point to the actual virgin yield point. 9.3.3 Acceptance and Control Tests for Mechanical Properties of Virgin Sled provision applies to steel produced to other than IS : 1079-19737 when used in sections for which the increased yield point and ultimate strength of the steel after cold forming are computed from the virgin steel properties according to 6.1.1.1. For acceptance and control

This

*Method for tehsiletesting of steel products (Jirrl feuision). tSpecification for hot rolled carbon steel sheet and strip 35

(did

recision).

ls

: 801- 1975
lot as of the taken of the

purposes, at least four tensile specimens shall be taken from each defined in 9.3.1(d) for the establishment of the representative values Specimens shall be virgin tcnjile yield point and ultimate strength. longitudinally from the quarter points of the width near the outer end coil.

APPENDIX,
COMPRESSION

A
TESTING

(Cluuse
A-L

9.3)
tests be made on flat-end ~pecitimes the largest dimension of the than 20 times the least radius of are to be used to check yield point the section should not be less than

It is recommended that stud column whose length is not less than three section except that it shall be not more gyration. If tests of ultimate compressive strength for quality control purposes, the length of 15 times the least radius of gyration.
mens

It is important, in making compression tests, that care be exercised in centering the specimen in the testing machine so that the load is applied concentrically with respect to the centroidal axis of the section. A-2. For further information regarding be made to the following publications: compression testing, reference may

ASTM E9 Standard method of compression testing of metallic materials at room temperature issued by the American Society for Testing and Materials. Technical memoranda No. 2 and 3 of the Column Research Council. Kotcs on Compression Testing of Materials and Procedures reprinted in the Column Research Design Criteria for Metal Compression Members. Stub-Column Test Council Guide to 2nd Ed. 1966.

36

(-dPran

pcr~ 2)

Panel for Use of Light Gauge Cold Formed Sections in Structural Engineering, SMBDC 7 : P-26 ConwIur
SHUNC. BALAWQRAMANIAN Members SHRI B. N. DAS
REPRE~~~I~AT~VE

Rejwescnting
Research Design Lucknow & Standa& Organization,

REPSSBNTATIVE

Tube Products of India, Madras Tata Engineerin & Locomotive Co, Jamshedptir Integral Coach s actory, Perumbur

37

BUREAU

OF INDIAN STANDARDS

Headquarters Manak Bhavan, 9 Bahadur Shah Zafar.Marg, NEW DELHI 110002 Telephones: 323 0131 I 323 3375,323 9462 Fax :+ 91 11 3234062,3239399, Internet : http://wwwdel.vsnl.net.in/bis,org E - mail : bisind @ del P.vsnl.net.in Central Laboratory

3239382

Telephone 91-77 00 32

Plot No. 20/9, Site IV, Sahibabad Industrial Area, Sahibabad 201010 Regional Offices: Central *Eastern

: Manak Bhavan, 9 Bahadur Shah Zafar Marg, NEW DELHI 110002 : l/l 4 CIT Scheme VII, V.I.P. Road, Kankurgachi, CALCUTTA 700054
160022

323 76 17 337 86 62 60 38 43 235 23 15 832 92 95

Northern : SC0 335-336, Sector 34-A, CHANDIGARH Southern

: C.I.T. Campus, IV Cross Road, CHENNAI 600113

tWestem : Manakalaya, E9, MIDC, Behind Marol Telephone Exchange, Andheri (East), MUMBAI 400093 Branch Offices: Pushpak, Nurmohamed Shaikh Marg, Khanpur, AHMEDABAD SPeenya Industrial Area, 1 st Stage, Bangalore-Tumkur Road, BANGALORE 560058 Commercial-cum-Cffice Complex, Opp. Dushera Maidan, Arera Colony, Bittan Market, BHOPAL 462016 62/63, Ganga Nagar, Unit VI, BHUBANESHWAR 751001 641037 380001

550 13 48 839 49 55 72 34 52 40 36 27 21 01 41 91-28 88 01 91-71 1998

Kalai Kathir Building, 670 Avinashi Road, COIMBATORE Plot No. 43, Sector 16 A, Mathura Road, FARIDABAD Savitri Complex, 116 G.T. Road, GHAZIABAD 201001

121001

53/5 Ward No.29, R.G. Barua Road, 5th By-lane, GUWAHATI 5-8-560, L.N:Gupta

781003 500901

566508 320 1084 37 38 79 21 68 76

Marg, Nampally Station Road, HYDERABAD JAIPUR 302001

E-52, Chitaranjan Marg, C-Scheme,

117/418 8, Sarvodaya Nagar, KANPUR 208005 Seth Bhawan, 2nd Floor, LUCKNOW 226005 Behind Leela Cinema, Naval Kishore

Road, 21 89 23 52 51 71 26 28 08 32 36 35 26 85 86

NIT Building, Second Floor, Gokulpat Market, NAGPUR 440010 Patliputra Industrial Estate, PATNA 800013 Institution of Engineers (India) Building 1332 Shivaji Nagar, PUNE 411005 Sahajanand House3rd floor, Bhakfjnagar Circle, 80 Feet Road, RAJKOT 360002 T.C. No. 14/1421, University P. 0. Palayam, THIRUVANANTHAPURAM *Sales Cffice is at 5 Chowringhee Approach, P.O. Princep Street, CALCUTTA 700072 tSales Cffice is at Novelty Chambers, Grant Road, MUMBAI 400007 *Sales Cffice is at F Block, Unity Building, Narashimaraja Square, BANGALORE 560002 695034

327215 271085 309 65 28 222 39-71

Printed at Dee Kay Printers, New Delhi-110015,

India.