Scribd
Upload
9K views2 pages

BSS Commands Nokia PDF

The document contains commands used to monitor and manage various network elements in a mobile network, including BTS, BSC, ET, and OMU units. The commands check status, alarms, traffic, power levels, and allow resetting, enabling, disabling and reconfiguring parameters of network elements.

Uploaded by

vukee
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9K views2 pages

BSS Commands Nokia PDF

The document contains commands used to monitor and manage various network elements in a mobile network, including BTS, BSC, ET, and OMU units. The commands check status, alarms, traffic, power levels, and allow resetting, enabling, disabling and reconfiguring parameters of network elements.

Uploaded by

vukee
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DOCUMENTTYPE TypeUnitOrDepartmentHere TypeYourNameHere 1. ZEEI; // To see the status of the site. 2.

ZEEP; // To see all the site & its BCF IDs. 3. ZEEL:BL; // To see the Blocked TRX in whole BSC. 4. ZEOL:BCF NO; // To check the current alarm in the site. 5. ZEOH::BCF=BCF NO; // To check history of alarm. 6. ZEOR:BCF NO:ALARM NO(10001-65534); // To cancel an alarm. 7. ZEFS:BCF NO:L/U; // To give site reset. 8. ZEFR:BCF NO:SITE/OMU; // To give site reset in safe mode also OMU reset. 9. ZEQS:BTS=BTS NO:L/U; // To give sector reset. 10. ZERS:BTS=BTS NO,TRX=TRX NO:L/U; // To give TRX reset. TypeDateHere

1 (2)

11. ZERM:BTS=BTS NO,TRX=TRX NO:GTRX=Y/N; // To give reset if TRX is blocked by system. 12. ZERM:BTS=BTS NO,TRX=TRX NO:PREF=P/N; // To change preference for ACTIVE TRX. 13. ZWAT; // To check BSC alarm TEXT ID. 14. ZAHO::NR=4000-4007; // To check BSC alarm. 15. ZAHO:ET,ET NO; // To check ET alarm. 16. ZAHP; // To check ET & BSC history alarms. 17. ZYEF:ET,ET NO; // To check PCM service state. 18. ZDTI:::PCM=ET NO; // To check signalling link for a site. 19. ZDSB:::PCM=ET NO; // To check TIE value & BIT rate. 20. ZUSC:ET,ET NO:BL/WO; // To give ET reset. 21. ZDTC:LAPD NAME:BL/WO; // To give LAPD reset. 22. ZYMO:ET,ET NO; // To check SLIPS. 23. ZUSI:ET,ET NO; // To check ET status. 24. ZWUP:ET NO; // To check the type of ET (ABIS or SIGNALLING). 25. ZERO:BCF=BCF NO; // To check traffic of the TRX. 26. ZESI:ID=BCF NO; // To check EDAP. 27. ZESI:ID=BCF NO:TRXS; // To check DAP TRX. 28. ZQUS:BCF=BCF NO,TRE=(RATIO);then 7;1;0; // To check receiving level. 29. ZNEL; // To check signalling link status. 30. ZEFP; // To check External Alarm ID. 31. ZEFT:BCF NO:ON/OFF; // To switch ON/OFF the DG. 32. ZEFO:BCF NO:IOP; // To check POLARITY. 33. ZEFX:BCF NO:INBR=INPUT ID:POL=OPEN/CLOSED; // To change the POLARITY. 34. ZEWV:BCF NO:BU; // To give SOFTWARE BACKUP. 35. ZEQE:BTS=BTS NO:AHOP=Y/N; // To remove ANTENNA HOP if PRESENT.

DOCUMENTTYPE TypeUnitOrDepartmentHere TypeYourNameHere 36. ZEUO:BTS=BTS NO; // To check BTS POWER. 37. ZEUG:BTS=BTS NO:PMAX1=(1,243); // To change BTS POWER. 38. ZEQV:BTS=BTS NO:GENA=Y/N; // To enable/disable GPRS. 39. ZEQO:BTS=BTS NO:GPRS; // To check GPRS ENABLED OR NOT for BTS. 40. ZFWO:BCSU=0&&6; // To check GPRS for particular BSC. 41. ZACC:CONSECUTIVE NO(XXXX); // To delete BSC Alarm. TypeDateHere

2 (2)

BTS UNITS: OMU BCSU CLS MB ET TCSM OPERATION & MAINTENANCE UNIT BASE STATION CONTROLLER SIGNALLING UNIT CLOCK & SYNCHRONIZATION UNIT MESSAGE BUS EXCHANGE TERMINAL TRANSCODER SUBMULTIPLEXER

MCMU MARKER AND CELLULAR MANAGEMENT UNIT

GENA GPRS ENABLED

You might also like