NEC LT265 Projector Manual

Portable Projector
LT265/LT245
Users Manual
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your NEC LT265/LT245 Projector and keep the manual handy for future
reference. Your serial number is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this
unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNITS PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS
CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST
BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.
DOC Compliance Notice (for Canada only)

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV (for Germany only):

The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
CAUTION
Do not look into the laser pointer while it is on and do not point the
laser beam at a person. Serious injury could result.
This label is underneath the remote control.
WARNING TO CALIFORNIA RESIDENTS:

Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
Copyright NEC Viewtechnology, Ltd. 2004
i
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by NEC Solutions (America), Inc. in this manual. Failure to comply with this government regulation could
void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with
this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.
Exposure to direct sunlight, smoke or steam can harm internal components.
4. To avoid premature lamp failure, do not tilt the front of the projector up or down by more than 7 from level.
5. Handle your projector carefully. Dropping or jarring can damage internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes.
d. Please consult your dealer for more information.
ii
Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside
your projector. Allow at least 4 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.
Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as
a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately
and have the object removed by a qualified NEC service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can
cause unpredictable outcome such as fire or injury to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to
melting of the cap and possibly burning your hands due to the heat emitted from the light output.
7. The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power
supply fits this requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
11. Do not handle the power plug with wet hands.
12. When using a LAN cable:
For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage.
CAUTION
Do not try to touch the ventilation outlet on the front side as it can become heated while the projector is turned
on.
Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or
hanging on the wall can cause damage to the projector.
Before putting the projector in the soft case, be sure to retract the feet. Failure to do so may cause the damage
to the projector.
Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside
the soft case could be damaged.
Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[Setup] [Options] [Fan Mode] [High].)
Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
* While the projector's lamp lights.
* While the cooling fans are running. (The cooling fans continue to work for 90 seconds after the projector is
turned off).
* While the PC CARD Access Indicator lights. Doing so can damage your PC memory card.
iii
Lamp Replacement
To replace the lamp, follow all instructions provided on page 119.
Be sure to replace the lamp when the message The lamp has reached the end of its usable life. Please
replace the lamp. appears. If you continue to use the lamp after the lamp has reached the end of its usable
life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
Allow a minimum of 90 seconds to elapse after turning off the projector. Then turn off the main power switch,
disconnect the power cable and allow 60 minutes to cool the projector before replacing the lamp.
iv
Table of Contents
Important Information ......................................................................... i
1. Introduction ...................................................................................... 1
What's in the Box? ........................................................................................................ 2
Introduction to the Projector ......................................................................................... 3
Part Names of the Projector ......................................................................................... 5
Carrying the Projector ............................................................................................. 5
Top Features ........................................................................................................... 7
Terminal Panel Features ......................................................................................... 8
Part Names of the Remote Control ............................................................................ 10
2. Installation and Connections .................................................... 13

Setting Up the Screen and the Projector .................................................................... 14
Selecting a Location .............................................................................................. 14
Throw Distance and Screen Size .......................................................................... 15
Making Connections ................................................................................................... 17
Enabling the computers external display .............................................................. 17
Connecting Your PC or Macintosh Computer ........................................................ 17
To connect SCART output (RGB) ......................................................................... 18
Connecting an External Monitor ........................................................................... 19
Connecting Your DVD Player with Component Output .......................................... 20
Connecting Your VCR or Laser Disc Player .......................................................... 21
Connecting to a Network ....................................................................................... 22
Inserting and Removing a PC Card ...................................................................... 24
Connecting the Supplied Power Cable ................................................................. 26
3. Projecting an Image (Basic Operation) ................................. 27

Turning on the Projector ............................................................................................. 28
Selecting a Source ..................................................................................................... 30
Adjusting the Picture Size and Position ...................................................................... 31
Correcting Keystone Distortion ................................................................................... 33
Optimizing an RGB Image Automatically ................................................................... 35
Turning Up or Down Volume ....................................................................................... 35
Using the Laser Pointer .............................................................................................. 36
Turning off the Projector ............................................................................................. 37
After Use ..................................................................................................................... 37
4. Convenient Features .................................................................... 38

Turning Off the Image and Sound ............................................................................... 39
Freezing a Picture....................................................................................................... 39
Using the Pointer ........................................................................................................ 39
Enlarging and Moving a Picture .................................................................................. 40
Getting Integrated Help .............................................................................................. 40
Using a USB Mouse ................................................................................................... 41
Using Remote Mouse Receiver .................................................................................. 42
v
Table of Contents
Correcting Horizontal and Vertical Keystone Distortion (Cornerstone) ....................... 43

Making Freehand Drawings on a Projected Image (ChalkBoard) .............................. 46
Storing Images Displayed on the Projector on the PC card or USB Memory (Capture) .......... 47
Preventing Unauthorized Use of the Projector ........................................................... 48
Using a USB Memory Device or USB Memory Card Reader ..................................... 53
Operation Using an HTTP Browser ............................................................................ 54
Using the Projector to Operate a Computer Connected on a Network
(Desktop Control Utility 1.0) .................................................................................. 57
5. Using the Viewer ........................................................................... 62

Making the Most out of the Viewer Function ............................................................... 63
Operating the Viewer Function from the Projector (playback) .................................... 64
Changing Background Logo ....................................................................................... 70
6. Using On-Screen Menu ................................................................ 71

Using the Menus ......................................................................................................... 72
Menu tree ................................................................................................................... 73
Menu Elements ........................................................................................................... 75
Menu Descriptions & Functions [Source] ................................................................... 76
Menu Descriptions & Functions [Adjust] ..................................................................... 79
Menu Descriptions & Functions [Setup] ..................................................................... 90
Menu Descriptions & Functions [Information] ........................................................... 112
Menu Descriptions & Functions [Reset] ................................................................... 116
7. Maintenance ................................................................................. 117

Cleaning the Cabinet ................................................................................................ 118
Cleaning the Lens..................................................................................................... 118
Replacing the Lamp .................................................................................................. 119
8. Appendix ........................................................................................ 122

Troubleshooting ........................................................................................................ 123
Specifications ........................................................................................................... 126
Cabinet Dimensions ................................................................................................. 128
Pin Assignments of D-Sub COMPUTER 1/2 Input Connector ................................. 129
Compatible Input Signal List ..................................................................................... 130
PC Control Codes and Cable Connection ................................................................ 131
Using Software Keyboard ......................................................................................... 132
Troubleshooting Check List ....................................................................................... 133
TravelCare Guide ...................................................................................................... 135
vi
1
Introduction
What's in the Box? ....................................................... 2
Introduction to the Projector ........................................ 3
Part Names of the Projector ........................................ 5

Carrying the Projector ............................................................................................ 5
Top Features ........................................................................................................... 7
Terminal Panel Features ......................................................................................... 8
Part Names of the Remote Control ........................... 10

Battery Installation ................................................................................................ 12
Operating Range for Wireless Remote Control .................................................... 12
Remote Control Precautions ................................................................................ 12
1
1. Introduction
What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your Projector.
Projector
Soft case
(24BS7114)
Lens cap
(24FT9351)
Remote control Batteries (AAA 2) Remote mouse receiver

(7N900491) (7N900561)
Power cable RGB/VGA signal cable

(7N080204) US (7N520032)
(7N080003) EU
Qu nec
Co id
ic t
k
n e
Gu
Im orm
In
po at
f
rta ion
nt
So tal a
NE e Ut Guid
Ins
ftw tio
C ilit e
ar n
CD-ROM
Users manual and User Supportware 2
For North America only Security sticker

Registration card
Limited warranty
For Europe only
Guarantee policy
2
1. Introduction
Introduction to the Projector

This section introduces you to the LT265/LT245 Projector and describes key features and controls.
Congratulations on Your Purchase of the LT265/LT245 Projector

The LT265/LT245 is a sophisticated XGA projector that produces an enhanced display. With the LT265/LT245 you will
be able to project images up to 500 (measured diagonally). Enjoy crisp and sharp large screen display from your PC,
workstation or Macintosh computer, DVD player, VCR, satellite hookup, HDTV source, ) and images from your digital
camera PC Card, compact flash memory or USB storage device. The LT265/LT245 provides for enhanced security
options to help deter projector theft and provides for full projector control through the PC control port (mini DIN 8Pin)
and LAN support. With input and output flexibility, long lamp life and a full function remote, the LT265/LT245 lets you
enjoy larger than life viewing from a compact and easy to setup and use projector.
Features youll enjoy on the LT265/LT245:

Automatic vertical keystone correction for fast and easy application setup.
3D Reform enhanced image technology for increased projector placement versatility that provides for
horizontal, vertical and diagonal keystone correction.
Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white
screen material (or a wall).
USB memory or PC card interfaces provide for computer-free presentations.
Enhanced smart security settings for password protection, cabinet control panel lock, menu lock and PC card
protection key to help prevent unauthorized access, adjustments and theft deterrence.
High resolution display - up to UXGA compatible, XGA native resolution.
Variable audio out control of external amplified speakers via the projector remote.
Extensive user adjustable picture and color management settings.
Display 16:9 or 4:3 aspect ratio sources and fill the screen.
HDTV (1080i, 720p) and SDTV (480p/576p, 480i/576i) compatibility.
Digital photo viewer to display larger than life images from your digital cameras PC card, compact flash card or
USB storage device.
Integrated RJ-45 connector for wired networking capability.
Wireless networking capable.
Present from anywhere in the room when using as a wireless LAN projector, no physical signal cable connec-
tion to a PC is required.
* The NEC optional wireless LAN card is required (NWL-100* See page 99.).
Supplied User Supportware 2 CD-ROM containing five software utilities allowing you to make the most of your
NEC projector.
The supplied wireless remote control and remote mouse receiver allows you to operate your PC mouse wireless
from across the room. The remote mouse receiver supports most PCs with USB interface.
Easy set up, use and operation.
Eco-mode lamp technology for increased lamp life, reduced energy consumption and overall total cost of
ownership savings.
Built-in laser pointer on the supplied remote control allows you to draw your audience's attention in a presenta-
tion.
3
1. Introduction
Free downloadable Software Geometric Correction Tool 2.0.

Corrects the geometry of an image projected onto a cylindrical, spherical or corner screen via serial connection.
For additional information visit:
US : http://www.necvisualsystems.com
Europe : http://www.neceurope.com/
Global : http://www.nec-pj.com/
About this user's manual

The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an
overview. If the section doesn't apply, you can skip it.
IBM is a trademark or registered trademark of International Business Machines Corporation.

Mac, Macintosh and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other
countries.
Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks
of Microsoft Corporation.
Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
Ulead is a trademark and/or registered trademark of Ulead Systems, Inc.
Other product and company names mentioned in this users manual may be the trademarks or registered
trademarks of their respective holders.
4
1. Introduction
Part Names of the Projector
Controls
Zoom Lever
(See page 7)
(See page 32)
Focus Ring
(See page 32) Built-in Security Slot ( )*
Remote Sensor
(See page 12)
Ventilation (outlet) Ventilation (inlet)

Heated air is exhausted
from here.
Adjustable Tilt Foot Lever Carrying Handle

(See page 31)
Lens
Adjustable Tilt Foot
(See page 31) Lens Cap
* This security slot supports the MicroSaver Security System. MicroSaver is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Carrying the Projector

Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the
projector.
When moving the projector or when it is not in use, cover the lens with the lens cap.
5
1. Introduction
Monaural Speaker (2W)

PC Card Eject Button
PC Card Slot
Lamp cover
(See page 119)
Ventilation (outlet)
Remote Sensor
(See page 12)
Lamp cover screw
Rear Foot
Rear Foot
AC Input Rotate to make the projector level.
Connect the supplied power cable's (See page 31)
three-pin plug here, and plug the other
end into an active wall outlet. Main Power Switch
(See page 26) When you plug the supplied power cable into an active wall
outlet and turn on the Main Power switch, the POWER
indicator turns orange and the projector is in standby mode.
(See page 28)
6
1. Introduction
Top Features
9 10 4 5 11
MEN U
SOURCE AUTO ADJUST

SELECT
LAMP
EN
STATUS 2
TE IT 3D REFORM ON/STAND BY POWER
R EX
PC CARD
6 7 8 12 1 3
1. POWER Button (ON / STAND BY) 6. PC CARD Access Indicator
Use this button to turn the power on and off when the Lights while accessing a PC card.
main power is supplied and the projector is in standby
mode.
7. ENTER Button
NOTE: To turn on the projector, press and hold this button
for a minimum of two seconds. To turn off the projector, Executes your menu selection and activates items
press this button twice. selected from the menu.
2. STATUS Indicator 8. EXIT Button

If this light blinks red rapidly, it indicates that an error Pressing this button will return to the previous menu
has occurred, the lamp cover is not attached properly with saving changes.
or the projector has overheated. If this light remains While you are in the main menu, pressing this button
orange, it indicates that you have pressed a cabinet will close the menu.
key while the Cabinet Button Lock is enabled. See the
Status Indicator section on page 123 for more details. 9. SELECT (+) () / Volume Buttons
: Use these buttons to select the menu of the
3. POWER Indicator ( ) item you wish to adjust.
When this indicator is green, the projector is on; when : Use these buttons to change the level of a
this indicator is orange, it is in standby mode. See the selected menu item. When no menus appear,
Power Indicator section on page 123 for more details.
these buttons work as a volume control.
When the pointer is displayed, these buttons
4. SOURCE Button move the pointer.
Use this button to select a video source such as a PC,
VCR, DVD player or Viewer (PC card).
10. MENU Button
Press and release this button quickly to display the
Source List. Displays the menu.
Each time this button is pressed for a minimum of ONE 11. LAMP Indicator
second, the input source will change as follows:
If this light blinks red rapidly, it's warning you that the
projection lamp has exceeded 2000 hours (up to 4000
Computer1 Computer2 Video S-Video hours in Eco mode) of service. After this light appears,
Viewer Computer1 ... replace the lamp as soon as possible. (See page 119).
If this is lit green continually, it indicates that the lamp
If no input signal is present, the input will be skipped. mode is set to Eco. See the Lamp Indicator section
on page 123 for more details.
5. AUTO ADJUST Button

12. 3D REFORM Button
Use this button to adjust an RGB source for an opti-
mal picture (See page 35). Press this button to enter 3D Reform mode to correct
the keystone (trapezoidal) distortion, and make the
image square.
7
1. Introduction
Terminal Panel Features
13 12 11 10 9 3 5
AUDIO OUT
PC CARD LAN USB

R AUDIO IN L VIDEO IN S-VIDEO IN PC CONTROL COMPUTER 1 IN AUDIO IN COMPUTER 2 IN MONITOR OUT
8 7 6 1 2 4
1. COMPUTER 1 IN / Component Input Connector 6. S-VIDEO IN Connector (Mini DIN 4 Pin)

(Mini D-Sub 15 Pin) Here is where you connect the S-Video input from an
Connect your computer or other analog RGB equip- external source like a VCR.
ment such as IBM compatible or Macintosh comput- NOTE: S-Video provides more vivid color and higher
ers. Use the supplied RGB/VGA signal cable to con- resolution than the traditional composite video format.
nect to your computer. This also serves as a compo-
nent input connector that allows you to connect a com- 7. VIDEO IN Connector (RCA)
ponent video output of component equipment such Connect a VCR, DVD player, laser disc player, or docu-
as a DVD player. This connector also supports SCART ment camera here to project video.
output signal. See page 18 for more details.
8. VIDEO AUDIO IN Jacks (RCA)
2. COMPUTER 2 IN / Component Input Connector
L: This is your left channel audio input for stereo
(Mini D-Sub 15 Pin)
sound coming from the VIDEO source.
This connector has the same function as the COM- R: This is your right channel audio input for stereo
PUTER 1 IN connector. sound from the VIDEO source.
NOTE: The COMPUTER 2 IN does not support SCART
output signal and Plug & Play. 9. PC CONTROL Port (Mini DIN 8 Pin)
Use this port to connect your PC or control system to
3. COMPUTER AUDIO IN Mini Jack (Stereo Mini)
control your projector via a serial cable. This enables
This is where you connect audio output from your com- you to control the projector using serial communica-
puter or DVD player. A commercially available audio tion protocol. The NEC optional serial cable (CA03D)
cable is required. is required to use this port. You can also control the
projector by using PC Control Utility 3.0 contained on
4. MONITOR OUT Connector (Mini D-Sub 15 Pin) the supplied User Supportware 2 CD-ROM.
You can use this connector to loop your computer To do so you must first have PC Control Utility 3.0
image to an external monitor from the COMPUTER 1 installed on your PC. If you are writing your own pro-
or 2 input source. gram, typical PC control codes are on page 131.
The RGB analog signal set on OUT Terminal is out-
put during Standby mode. See pages 19 and 109. 10. USB Port (Type A)
Connect a commercially available USB memory de-
5. AUDIO OUT Mini Jack (Stereo Mini) vice or mouse that supports USB. You can operate
Connect an additional audio equipment here to listen the menu or Viewer with the USB mouse via this port.
to audio coming from your computer, Video or S- Video Note that this port should not be connected to a com-
input. puter and that there may be some brands of USB
Output sound level can be adjusted in accordance mouse that the projector does not support.
with the sound level of the internal speaker.
11. LAN Port (RJ-45)
When audio equipment is connected, the projec-
tor speaker is disabled. This port is typically used for UTP Ethernet/Fast
Ethernet. Use this connector to control the projector
This jack cannot be used as a headphone jack.
on a LAN. See page 22.
8
1. Introduction
Terminal Panel Features
13 12 11 10 9 3 5
AUDIO OUT
PC CARD LAN USB

8 7 6 1 2 4
12. PC CARD Eject Button

Press to eject a PC card partially.
13. PC CARD Slot

Insert a PC memory card or NEC optional wireless
LAN card here.
9
1. Introduction
Part Names of the Remote Control
1. Infrared Transmitter/Laser Pointer

1 Transmits an infrared signal when any button other
2 than LASER is pressed.
Direct the remote control toward the remote sensor
4
OFF
POWER
ON
3 on the projector cabinet.
MAGNIFY
LASER
PAGE 6 Beams a laser light when the Laser button is pressed.
UP
5 POINTER
DOWN
8 CAUTION:
7 * Do not look into the laser pointer while it is on.
* Do not point the laser beam at a person.
9 10
2. LED
11 12 Flashes when any button is pressed.
3. POWER ON Button
13
15 17 When the main power is on, you can use this button
VIDEO COMPUTER LAN
to turn your projector on.
16 1 20 NOTE: To turn on the projector, press and hold the
S-VIDEO VIEWER
2 26 POWER ON button for a minimum of two seconds.
18 PIC-MUTE AUTO ADJ. SLIDE
21 VOLUME HELP 27 4. POWER OFF Button
22 ASPECT PICTURE
19 You can use this button to turn your projector off.
NOTE: To turn off the projector, press the POWER
24 FREEZE 3D REFORM
28 OFF button twice.
23 29
5. MAGNIFY (+)() Buttons
25 Use these buttons to adjust the image size.
The image can be magnified about the center of the
screen up to 400%. See page 40.
6. LASER Button
14 Press and hold this button to activate the laser pointer.
When lit, you can use the laser to draw your audience's
attention to a red dot that you can place on any ob-
ject.
7. POINTER Button
Press this button to display the projector pointer. You
can move your pointer icon to the area you want on
the screen using the Select button. See page 39.
8. PAGE UP/DOWN Buttons

Use these buttons to operate your computer with the
supplied remote mouse receiver. You can use these
buttons to scroll the viewing area of the window or to
move to the previous or next slide in PowerPoint on
your computer.
9. MENU Button
Displays the menu for various settings and adjust-
ments.
10
1. Introduction
10. Select Button 23. FREEZE Button

This button is used for projectors menu operation and This button will freeze a picture. Press again to re-
moving the magnified image. sume motion. See page 39.
This button also works as a computer mouse when
the supplied remote mouse receiver is connected with 24. HELP Button
your computer. See page 42. Provides the Information screen. See page 40.
11. ENTER Button 25. ASPECT Button

Executes your menu selection and activates items Press this button to display the Aspect Ratio select
selected from the menu. menu. See page 81.
12. EXIT Button 26. VIEWER Button

Returns to the previous menu. Press this button to select the Viewer source. See page
While you are in the main menu, pressing this button 64.
will close the menu.
27. SLIDE +/- Buttons
13. R-CLICK Button Press (+) to select the next folder or slide and press
Works as the mouse right button when the supplied () to select the previous folder or slide.
remote mouse receiver is connected with your com-
puter. 28. PICTURE Button
Press to display the picture adjustment screen. Press-
14. L-CLICK Button ing this button sequentially selects "Brightness"
Works as the mouse left button when the supplied "Contrast" "Color" "Hue" "Sharpness" "Wall
remote mouse receiver is connected with your com- Color". See pages 79 and 80.
puter.
29. 3D REFORM Button
15. VIDEO Button Press this button to enter 3D Reform to correct the
Press this button to select a video source from a VCR, keystone (trapezoidal) distortion, and make the im-
DVD player, laser disc player or document camera. age square. See pages 33 and 43.
16. S-VIDEO Button

Press this button to select an S-Video source from a
VCR.
17. COMPUTER 1 Button

Press this button to select COMPUTER 1 input.
18. COMPUTER 2 Button

Press this button to select COMPUTER 2 input.
19. AUTO ADJ. Button

Use this button to adjust an RGB source (COMPUTER
1 or 2) for an optimal picture. See page 35.
20. LAN Button

Press this button to select the LAN (Local Area Net-
work) connection.
21. PIC-MUTE Button

This button turns off the image and sound for a short
period of time. Press again to restore the image and
sound. See page 39.
22. VOLUME +/ Buttons

Press (+) to increase the volume and () to decrease
it. See page 35.
11
1. Introduction
Battery Installation
1 Remove the battery cover. 2 Remove both old batteries and 3 Slip the cover back over the bat-
NOTE: Do not pull the battery install new ones (AAA). Ensure teries until it snaps into place.
cover by force. Doing so can that you have the batteries' po- NOTE: Do not mix different types of
result in it coming off. larity (+/ ) aligned correctly. batteries or new and old batteries.
2
1
1
Operating Range for Wireless Remote Control
7m/22 feet 7m/22 feet
30
30
30
Remote control
30
Remote sensor on projector cabinet
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor.
Weak batteries will also prevent the remote control from properly operating the projector.
Remote Control Precautions

Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
If you will not be using the remote control for a long time, remove the batteries.
Do not place the batteries upside down.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
12
2
Installation and Connections
Setting Up the Screen and the Projector ................... 14

Selecting a Location ............................................................................................. 14
Throw Distance and Screen Size ......................................................................... 15
Making Connections .................................................. 17

Enabling the computers external display ............................................................. 17
Connecting Your PC or Macintosh Computer ....................................................... 17
To connect SCART output (RGB) ......................................................................... 18
Connecting an External Monitor ........................................................................... 19
Connecting Your DVD Player with Component Output ......................................... 20
Connecting Your VCR or Laser Disc Player .......................................................... 21
Connecting to a Network ...................................................................................... 22
Inserting and Removing a PC Card ...................................................................... 24
Connecting the Supplied Power Cable ................................................................. 26
13
2. Installation and Connections
This section describes how to set up your projector and how to connect PCs, video and audio sources.
Your projector is simple to set up and use.

1 But before you get started, you must first:
z Set up a screen and the projector.

x Connect your computer or video equip-
ment to the projector. See pages 17 -
25.
c Connect the supplied power cable. See
page 26.
2
3
NOTE: Ensure that the power cable and any
other cables are disconnected before moving
the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.
To the wall outlet.
Setting Up the Screen and the Projector

Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 30 inches (0.8 m) measured diagonally when the projector is roughly 51.2 inches (1.3 m) from the wall
or screen. The largest the image can be is 500 inches (12.7 m) when the projector is about 970 inches (24.6 m) from
the wall or screen. Use the drawing below as a guide.
Screen size (Unit: cm/inch)
609.6 (W) 457.2 (H) / 240 (W) 180 (H)
30 Screen size
0"
487.7 (W) 365.8 (H) / 192 (W) 144 (H)

24
0"
406.4 (W) 304.8 (H) / 160 (W) 120 (H)
20
365.8 (W) 274.3 (H) / 144 (W) 108 (H) 0"
18
0"
304.8 (W) 228.6 (H) / 120 (W) 90 (H)
15
0"
243.8 (W) 182.9 (H) / 96 (W) 72 (H)
12
203.2 (W) 152.4 (H) / 80 (W) 60 (H)
0"
4)
10
.
12
0"
4
5/
162.6 (W) 121.9 (H) / 64 (W) 48 (H)

0.
(1
80
.0
28
.4 )
"
13 9.5
/5
121.9 (W) 91.4 (H) / 48 (W) 36 (H)

2
/3
.4
60
(8
e 422 3)
nc .7/ 74.
.0
81.3 (W) 61.0 (H) / 32 (W) 24 (H) "

ta 10 .0/2 )
(7 .7
3 6
1. /24
8. .9 )
4
35 .3
5 .2
61.0 (W) 45.7 (H) / 24 (W) 18 (H)

30 0"
9/ (6
31 05
0/ /2
9 )
8. 5.2
2. 3.8
"
6. 4.2 )
(
26 6
( 2
7/ /1
9 6.
Lens center
3/ 3. 6)
9. 13
5. 5 ( 08.
is
20 5/
4. 9. 80. 3.8
D
. /1
1 39 .8
4 2 9)
.4 /6 )
.0 /50
74 .8
(1 .7 .5
13 .1/ 0
5/ (2 .6/1
/1 (2
3. 5
(1 .3
/5 8.
3)
/
1
3. 2
Unit: m/inch
NOTE:
Values in parentheses for LT245.
The screen sizes above are intermediate values between tele (minimum display area) and wide (maximum display area). Image
size can be adjusted with the zoom adjustment up to a maximum of 10%.
To avoid premature lamp failure, do not tilt the front of the projector up or down by more than 7 from level.
14
Throw Distance and Screen Size Screen Width

The following shows the proper relative positions of the pro-
jector and screen. Refer to the table to determine the posi-
tion of installation.
Screen Diagonal
Screen Height Screen center

Distance Chart
B = Vertical distance between lens center and screen cen-
ter
C = Throw distance (B)
D = Vertical distance between lens center and bottom of Screen Bottom

screen (top of screen for ceiling application)
= Throw angle (D)
Lens Center
NOTE: Distances may vary +/-5%.

Throw Angle ()
Throw Distance (C)
LT265
Screen Size B C D Screen Size B C D
Diagonal Width Height Wide Tele Wide Tele Diagonal Width Height Wide Tele Wide Tele
inch inch inch inch inch inch degree inch mm mm mm mm mm mm degree
30 24 18 12.6 45.6 56.0 3.6 15.4 12.7 30 762 610 457 320 1,157 1,423 91 15.4 12.7
40 32 24 16.8 61.5 75.4 4.8 15.3 12.6 40 1016 813 610 427 1,563 1,915 122 15.3 12.6
60 48 36 25.2 93.5 114.1 7.2 15.1 12.5 60 1524 1219 914 640 2,375 2,899 183 15.1 12.5
67 54 40 28.1 104.7 127.7 8.0 15.0 12.4 67 1702 1361 1021 714 2,659 3,243 204 15.0 12.4
72 58 43 30.2 112.7 137.4 8.6 15.0 12.4 72 1829 1463 1097 768 2,862 3,489 219 15.0 12.4
80 64 48 33.6 125.5 152.9 9.6 15.0 12.4 80 2032 1626 1219 853 3,187 3,883 244 15.0 12.4
84 67 50 35.3 131.9 160.6 10.1 15.0 12.4 84 2134 1707 1280 896 3,349 4,080 256 15.0 12.4
90 72 54 37.8 141.5 172.2 10.8 15.0 12.4 90 2286 1829 1372 960 3,593 4,375 274 15.0 12.4
100 80 60 42.0 157.4 191.6 12.0 14.9 12.4 100 2540 2032 1524 1067 3,999 4,867 305 14.9 12.4
120 96 72 50.4 189.4 230.3 14.4 14.9 12.3 120 3048 2438 1829 1280 4,811 5,851 366 14.9 12.3
150 120 90 63.0 237.3 288.4 18.0 14.9 12.3 150 3810 3048 2286 1601 6,028 7,327 458 14.9 12.3
180 144 108 75.6 285.3 346.6 21.6 14.8 12.3 180 4572 3658 2743 1921 7,246 8,802 549 14.8 12.3
200 160 120 84.0 317.2 385.3 24.0 14.8 12.3 200 5080 4064 3048 2134 8,058 9,786 610 14.8 12.3
210 168 126 88.2 333.2 404.7 25.2 14.8 12.3 210 5334 4267 3200 2241 8,464 10,278 641 14.8 12.3
240 192 144 100.8 381.2 462.8 28.8 14.8 12.3 240 6096 4877 3658 2562 9,682 11,754 733 14.8 12.3
261 209 157 109.7 414.7 503.4 31.4 14.8 12.3 261 6629 5304 3978 2786 10,534 12,787 797 14.8 12.3
270 216 162 113.5 429.1 520.9 32.5 14.8 12.3 270 6858 5486 4115 2882 10,899 13,230 824 14.8 12.3
300 240 180 126.1 477.0 579.0 36.1 14.8 12.3 300 7620 6096 4572 3202 12,117 14,706 916 14.8 12.3
350 280 210 147.1 557.0 675.8 42.1 14.8 12.3 350 8890 7112 5334 3736 14,147 17,166 1069 14.8 12.3
400 320 240 168.1 636.9 772.7 48.1 14.8 12.3 400 10160 8128 6096 4270 16,176 19,626 1222 14.8 12.3
450 360 270 189.1 716.8 869.5 54.1 14.8 12.3 450 11430 9144 6858 4804 18,206 22,086 1375 14.8 12.3
500 400 300 210.1 796.7 966.4 60.1 14.8 12.3 500 12700 10160 7620 5337 20,235 24,545 1527 14.8 12.3
LT245
Screen Size B C D Screen Size B C D
Diagonal Width Height Wide Tele Wide Tele Diagonal Width Height Wide Tele Wide Tele
inch inch inch inch inch inch degree inch mm mm mm mm mm mm degree
30 24 18 12.5 35.7 43.3 3.5 19.4 16.2 30 762 610 457 319 906 1,100 90 19.4 16.2
40 32 24 16.7 48.2 58.4 4.7 19.1 16.0 40 1016 813 610 425 1,225 1,483 120 19.1 16.0
60 48 36 25.1 73.3 88.5 7.1 18.9 15.9 60 1524 1219 914 639 1,863 2,248 181 18.9 15.9
67 54 40 28.1 82.1 99.1 8.0 18.9 15.8 67 1702 1361 1021 713 2,086 2,516 203 18.9 15.8
72 58 43 30.2 88.4 106.6 8.6 18.8 15.8 72 1829 1463 1097 766 2,246 2,707 218 18.8 15.8
80 64 48 33.5 98.5 118.7 9.5 18.8 15.8 80 2032 1626 1219 852 2,501 3,014 242 18.8 15.8
84 67 50 35.2 103.5 124.7 10.0 18.8 15.8 84 2134 1707 1280 894 2,628 3,167 254 18.8 15.8
90 72 54 37.7 111.0 133.7 10.7 18.8 15.8 90 2286 1829 1372 958 2,820 3,396 273 18.8 15.8
100 80 60 41.9 123.6 148.8 11.9 18.7 15.7 100 2540 2032 1524 1065 3,139 3,779 303 18.7 15.7
120 96 72 50.3 148.7 178.9 14.3 18.7 15.7 120 3048 2438 1829 1278 3,776 4,545 364 18.7 15.7
150 120 90 62.9 186.3 224.1 17.9 18.7 15.7 150 3810 3048 2286 1598 4,733 5,693 455 18.7 15.7
180 144 108 75.5 224.0 269.3 21.5 18.6 15.7 180 4572 3658 2743 1918 5,689 6,841 547 18.6 15.7
200 160 120 83.9 249.1 299.5 23.9 18.6 15.7 200 5080 4064 3048 2132 6,327 7,607 608 18.6 15.7
210 168 126 88.1 261.7 314.5 25.1 18.6 15.7 210 5334 4267 3200 2238 6,646 7,989 638 18.6 15.7
240 192 144 100.7 299.3 359.7 28.7 18.6 15.6 240 6096 4877 3658 2558 7,603 9,137 729 18.6 15.6
261 209 157 109.5 325.7 391.4 31.2 18.6 15.6 261 6629 5304 3978 2782 8,272 9,941 793 18.6 15.6
270 216 162 113.3 337.0 405.0 32.3 18.6 15.6 270 6858 5486 4115 2878 8,559 10,286 821 18.6 15.6
300 240 180 125.9 374.6 450.2 35.9 18.6 15.6 300 7620 6096 4572 3198 9,516 11,434 912 18.6 15.6
350 280 210 146.9 437.4 525.5 41.9 18.6 15.6 350 8890 7112 5334 3731 11,110 13,348 1064 18.6 15.6
400 320 240 167.9 500.2 600.8 47.9 18.6 15.6 400 10160 8128 6096 4264 12,705 15,261 1216 18.6 15.6
450 360 270 188.9 563.0 676.2 53.9 18.5 15.6 450 11430 9144 6858 4798 14,299 17,175 1369 18.5 15.6
500 400 300 209.9 625.7 751.5 59.9 18.5 15.6 500 12700 10160 7620 5331 15,893 19,089 1521 18.5 15.6
15
WARNING Ensure that you have adequate ventilation around your

* Installing your projector on the ceiling must be done projector so heat can dissipate. Do not cover the vents
by a qualified technician. Contact your NEC dealer for on the side or the front of the projector.
more information.
* Do not attempt to install the projector yourself. Reflecting the Image
Only use your projector on a solid, level surface. If the Using a mirror to reflect your projector's image enables
projector falls to the ground, you can be injured and you to enjoy a much larger image. Contact your NEC
the projector severely damaged. dealer if you need a mirror system. If you're using a mir-
Do not use the projector where temperatures vary ror system and your image is inverted, use the MENU
greatly. The projector must be used at temperatures and SELECT buttons on your projector cabinet or your
between 41F (5C) and 95F (35C). remote control to correct the orientation. See page 98.
Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.
16
Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the
power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after
connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power
management software.
Enabling the computers external display

Displaying an image on the notebook PCs screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the Fn key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.
Connecting Your PC or Macintosh Computer
AUDIO IN
COMPUTER 1 IN
NOTE: The COMPUTER 1 IN connector
AUDIO OUT
PC CARD LAN USB

supports Plug & Play (DDC2).

AC IN
COMPUTER 2 IN
RGB/VGA signal cable (supplied)

To mini D-Sub 15-pin connector on the projector. It is
recommended that you use a commercially available
NOTE: For older Macintosh, use distribution amplifier if connecting a signal cable longer
a commercially available pin than the supplied one.
adapter (not supplied) to
connect to your Mac's video
port.
PHONE
PHONE
Audio cable (not supplied)
IBM PC or Compatibles (Desktop type) IBM VGA or Compatibles (Notebook

or Macintosh (Desktop type) type) or Macintosh (Notebook type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image
for an impressive presentation.
To connect to a PC or Macintosh, simply:

1. Turn off the power to your projector and computer.
2. Use the supplied RGB/VGA signal cable to connect your PC or Macintosh to the projector.
3. Connect the supplied power cable. See page 26.
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer
you've connected to the projector.
17
NOTE: The LT265/LT245 is not compatible with video decoded outputs of either the NEC ISS-6020 and ISS-6010 switchers.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the AUTO ADJUST button on
the projector cabinet.
* When noise appears on the sides of the screen:
Use the Overscan feature to display the image correctly.
Be sure to change the Overscan to 0% before pressing the AUTO ADJ or AUTO ADJUST button, otherwise an image may be
displayed with its sides cut off.
To connect SCART output (RGB)

Projector
COMPUTER 1 IN
AUDIO OUT
PC CARD LAN USB

Video equipment such as DVD player AC IN
Female
ADP-SC1
Commercially available SCART cable
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-
quired for this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the projector and your video equipment.
2. Use the NEC ADP-SC1 SCART adapter and a commercially available SCART cable to connect the COMPUTER 1
IN connector of your projector and a SCART output (RGB) of your video equipment.
4. Turn on the power to the projector and your video equipment.
5. Use the COMPUTER 1 button on the remote control to select the COMPUTER 1 IN connector.
6. Press the MENU button on the remote control to display the menu.
7. From the menu, select [Setup] [Options] [Signal Select] [Computer 1] [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as
Euro-connector.
NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe. Contact your NEC dealer in Europe for more
information.
18
Connecting an External Monitor

AUDIO OUT
AUDIO OUT
PC CARD LAN USB

AC IN
MONITOR OUT
RGB/VGA signal cable (supplied)
AUDIO
IN
Audio cable (not supplied) RGB/VGA signal cable (not supplied)
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
image you're projecting.
To do so:
1. Turn off the power to your projector, monitor and computer.
2. Use an RGB/VGA signal cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on
your projector.
4. Turn on the projector, monitor and the computer.
NOTE:
The MONITOR OUT connector outputs an RGB signal during Standby mode.
When the projector is in the standby mode, the image may not be correctly displayed while the cooling fans are running
immediately after turning on or off the power.
Output sound level can be adjusted in accordance with the sound level.
When audio equipment is connected, the projector speaker is disabled.
Daisy chain connection is not possible.
19
Connecting Your DVD Player with Component Output
COMPUTER 1 IN
AUDIO OUT
PC CARD LAN USB

AC IN
Optional 15-pin - to - RCA (female)3 cable

(ADP-CV1)
Audio Equipment
AUDIO IN
Component video RCA3 L R
cable (not supplied)
DVD player
Y Cb Cr L R
Component AUDIO OUT
You can connect your projector to a DVD player with component output or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.

2. If your DVD player has a component video (Y,Cb,Cr) output, use a commercially available component video cable
(RCA3) and the optional 15-pin-to-RCA (female)3 cable to connect your DVD player to the COMPUTER IN
connector on the projector.
For a DVD player without component video (Y,Cb,Cr) output, use an S-Video cable (not provided) to connect an S-
Video output of the DVD player to the Video Input of the projector.
4. Turn on the projector and DVD player.
A component signal will be automatically displayed. If not, from the menu, select [Setup] [Options] [Signal
Select] [Computer 1 (or 2)] [Component].
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
20
Connecting Your VCR or Laser Disc Player
VIDEO IN
S-VIDEO IN AUDIO OUT
PC CARD LAN USB

AC IN
S-Video cable (not supplied)
Video cable (not supplied)
Audio equipment
VCR/ Laser disc player
AUDIO IN VIDEO S-VIDEO L R

L R VIDEO OUT AUDIO OUT
Use an RCA or S-Video cable (not provided) to connect the video and use RCA cables (not provided) to connect
the audio from your VCR, laser disc player or document camera to your projector.
To make these connections, simply:

1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of an RCA cable to the video output (or one end of an S-Video cable to the S-Video output
connector) on the back of your VCR or laser disc player, connect the other end to the appropriate video input on
your projector. Connect one end of a pair RCA cables (not supplied) to the audio output on the back of your VCR or
laser disc player, connect the other end to your audio equipment or to the appropriate audio input on the projector.
4. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter.
21
Connecting to a Network
The LT265/LT245 comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable.
Placing the optional wireless LAN card (NWL-100*) in the PC card slot of the projector also provides a wireless LAN
connection. To use a LAN connection, you are required to assign an IP address to the projector. For setting the LAN
mode, see page 99 (From the menu, select [Setup] [Installation] [LAN Mode])
With the LAN connection, two features are available: Projector control and Picture transmission.
Projector control feature

With the wired or wireless LAN connection, you can control (power on/off, input select, etc.) and receive information
from the projector over the network using a computer. The following two methods are available:
* Using the HTTP Server feature on the projector. See page 54.
* Using PC Control Utility 3.0 from the supplied User Supportware 2 CD-ROM.
Picture transmission feature

With the wired or wireless LAN connection, you can send images and slides from a personal computer to the projector
which then can be projected on the screen. The following two methods are available:
* Using Image Express Utility 2.0 from the supplied User Supportware 2 CD-ROM.
* Using Ulead Photo Explore 8.0 from the supplied User Supportware 2 CD-ROM.
With the USB mouse connected to the projector, you can also operate the desktop screen on your Windows PC
connected to the LAN or the wireless LAN.
* Using Desktop Control Utility 1.0 from the supplied User Supportware 2 CD-ROM.
NOTE: For information about the five software utilities (Image Express Utility 2.0, Desktop Control Utility 1.0, Ulead Photo
Explorer 8.0, Viewer PPT Converter and PC Control Utility 3.0) contained on the supplied Projector User Supportware 2.0 CD-
ROM, see the supplied NEC Software Utility Installation Guide. See also each online help of the software utilities for information
about their functions and operations.
Example of LAN connection

Server
(A) Example of wired LAN connection
Hub
LAN cable (not supplied)
LAN
AUDIO OUT
PC CARD LAN USB

AC IN
22
(B) Example of wireless LAN connection
(Network Type Mode: Infrastructure)
Access Point
Wired LAN
To make connection with a wired LAN via an access point, you need to select the Infrastructure mode.
From the menu, select [Setup] [Installation] [LAN Mode] [PC Card] [Advanced] [Network Type]
[Infrastructure].
(C) Example of wireless LAN connection (Network Type Mode: 802.11 Ad Hoc)
To enable direct communication (i.e., peer-to-peer) between personal computers and projectors, you need to
select the 802.11 Ad Hoc mode.
From the menu, select [Setup] [Installation] [LAN Mode] [PC Card] [Advanced] [Network Type]
[802.11 Ad Hoc].
The 802.11 Ad hoc mode complies with IEEE802.11 standard.
When in Ad Hoc mode, only 802.11b is available for communication method.

Data transmission speed in Ad Hoc mode is limited up to 11Mbps.
23
Inserting and Removing a PC Card

To insert the NEC optional wireless LAN card or a PC memory card (also referred to as PC card in this manual), follow
the steps below.
CAUTION:
* Direction for Inserting the PC Card
The PC card has a top and bottom and must be inserted into the PC card slot in a specific direction. It
cannot be inserted backwards or upside-down.
Attempting to force it into the slot in the wrong direction may break the internal pin and damage the card
slot. Refer to the PC card's operating instructions for the proper direction of insertion.
* Back up your PC card's data in case it will need to be restored.
* To prevent electrostatic discharge damage to the wireless LAN card, wear an anti-static wrist strap. If no
wrist strap is available, ground yourself by touching metal such as a door knob.
Inserting the PC Card

1. Turn off the main power switch before inserting the
PC card. (This step is needed only when the wireless
LAN card being inserted into the projector's PC
CARD slot)
2. Hold the PC card horizontally and insert it slowly into

the PC card slot with its top facing up.
PC card (not supplied)

The eject button pops out once the PC card is fully inserted.
Check that the PC card is fully inserted.
NOTE: Do not try to force the PC card into the slot or you may bend
the pins inside the slot.
Removing the PC Card

1. Make sure that the PC CARD access indicator is not lit. (This
step is needed only when the PC memory card being inserted
into the projectors PC CARD slot.)
NOTE: The PC CARD access indicator lights while its data is being
accessed.
Eject button
2. To remove the wireless LAN card, turn off the main power. (This
step is needed only when the wireless LAN card being inserted
into the projector's PC CARD slot)
3. Press the eject button. The PC card pops out a little. Grasp the
edges of the PC card and pull it out.
24
PC Card Type
The PC Card slot accepts PCMCIA Type II only.
NOTE: The projector does not support NTFS formatted flash memory card or USB memory device.
Be sure to use a flash memory card or USB memory device formatted with the FAT32, FAT16 or FAT file system.
To format your flash memory card or USB memory device in your computer, refer to the document or help file that comes with
your Windows operating systems.
25
Connecting the Supplied Power Cable

Connect the supplied power cable to the projector.
First connect the supplied power cable's three-pin plug to the AC IN of the projector, and then connect the other plug
of the supplied power cable in the wall outlet.
To wall outlet
Make sure that the prongs are fully

inserted into both the AC IN and the
wall outlet.
CAUTION:
Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector or PC card:
While the projector's lamp is lighted.
While the cooling fans are running. The cooling fans continue to work for 90 seconds after the projector is
turned off.
While the PC CARD Access Indicator lights. Doing so can damage your PC memory card.
26
3
Projecting an Image
(Basic Operation)
Turning on the Projector............................................. 28
Selecting a Source .................................................... 30
Adjusting the Picture Size and Position ..................... 31
Correcting Keystone Distortion .................................. 33
Optimizing an RGB Image Automatically ................. 35
Turning Up or Down Volume ...................................... 35
Using the Laser Pointer ............................................. 36
Turning off the Projector............................................. 37
After Use .................................................................... 37
27
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
Turning on the Projector

NOTE:
The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button (POWER ON and OFF on the
remote control).
When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off ()
position. Failure to do so may cause damage to the projector.
The projector has a feature to prevent itself from being used by unauthorized individuals. To use this feature, register a
keyword. See "Security" in "Setup" on page 48 for more details.
1. To turn on the main power to the projector, press the

Main Power switch to the on position ( I ).
The POWER indicator will light orange.
See the Power Indicator section on page 123 for more
details. LAMP
STATUS
POWER
2. Press the POWER (ON/STAND BY) button on the ME N U OFF

POWER
ON
projector cabinet or POWER ON button on the SOURCE AUTO ADJUST

MAGNIFY
LASER
PAGE
UP
remote control for a minimum of 2 seconds when the SELECT POINTER
LAMP DOWN
power indicator turns a steady green, and the

STATUS
EN
T ER IT 3D REFORM ON/STAND BY POWER
EX MEN U
projector is ready to use. PC CARD
EN T E R
E XI T
After you turn on your projector, ensure that the
computer or video source is turned on and that your R -C L I C K
lens cap is removed.

Blinking for
Standby one minute Power On
LAMP LAMP LAMP
STATUS STATUS STATUS
POWER POWER POWER
ON/STAND BY
Steady orange Blinking green Steady green
light light light
Press this button for a
minimum of 2 seconds.
See page 123 for more details.
NOTE: When no signal is available, a blue, black or logo screen is displayed.
28
Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 21 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT or button to select one of the

21 languages for the menu.
ME N U OFF ON
POWER
LASER
MAGNIFY PAGE
UP
SOURCE AUTO ADJUST
SELECT POINTER
LAMP DOWN
STATUS
EN
T IT
ER
EX
3D REFORM ON/STAND BY POWER MEN U
PC CARD
EN T E R
E XI T
R -C L I C K
ME N U
OFF ON
2. Press the ENTER button to execute the selection. MAGNIFY

POWER
LASER
PAGE
SOURCE AUTO ADJUST
UP
SELECT
POINTER
LAMP
DOWN
STATUS
EN
EX
MEN U
PC CARD
EN T E R
E XI T
R -C L I C K
3. To close the menu, press the EXIT button.

NOTE: Immediately after turning on the projector and MEN U
OFF
POWER
ON
displaying an image, you cannot turn off the projector for 60 SELECT
SOURCE AUTO ADJUST MAGNIFY
LASER
PAGE
UP
seconds. LAMP
STATUS
POINTER
DOWN
EN
EX
MEN U
After this has been done, you can proceed to the menu op- PC CARD
eration.
EN T E R
E XI T
If you want, you can select the menu language later. See "Lan-
R -C L I C K
guage" on page 91.
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp
lighting is stabilized.
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal
components to cool down.
When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp. See
page 119.
If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power.
29
Selecting a Source
Selecting the computer or video source
Using the Remote Control

Press any one of the COMPUTER 1/2, VIDEO, S-VIDEO, VIEWER or LAN but- VIDEO
R -C L I C K
LAN
COMPUTER
tons. S-VIDEO
1
VIEWER
2
PIC-MUTE AUTO ADJ. SLIDE
VOLUME HELP
ASPECT PICTURE
FREEZE 3D REFORM
Selecting from Source List MEN U
Press and quickly release the SOURCE button on the projector cabinet to display SOURCE AUTO ADJUST
SELECT
the Source list. Each time the SOURCE button is pressed, the input source will LAMP
STATUS
change as follows: Computer 1/2, Video (VCR or laser disc player), S-Video, EN
T ER EX
IT 3D REFORM ON/STAND BY POWER
Viewer (slides on a PC card) or LAN (LAN port [RJ-45] or wireless LAN card). PC CARD
To display the selected source, press the ENTER button.
Detecting the Signal Automatically

Press and hold the SOURCE button for a minimum of 1 second, the projector will MEN U
search for the next available input source. Each time you press and hold the SELECT
SOURCE AUTO ADJUST
SOURCE button for a minimum of 1 second, the input source will change as LAMP
STATUS
follows: EN
T ER EX
IT 3D REFORM ON/STAND BY POWER
PC CARD
Computer1 Computer2 Video S-Video Viewer Computer1 ...
If no input signal is present, the input will be skipped. When the input source you
wish to project is displayed, release the button.
30
Adjusting the Picture Size and Position

Place your projector on a flat level surface and ensure that the projector is
square to the screen.
Lift the front edge of the projector to center the image vertically.
If the projected image does not appear square to the screen, use the Keystone
feature for proper adjustment. See pages 33 and 43.
Rotate the front of the projector right or left (to the right in this example) to
center the image horizontally on the screen.
Adjust the Tilt Foot

1. Lift the front edge of the projector. Adjustable Tilt
Foot Button
1
2. Push up and hold the Adjustable Tilt Foot Button on the front of
the projector to extend the adjustable tilt feet.
3. Lower the front of the projector to the desired height. 2
Adjustable Tilt Foot

4. Release the Adjustable Tilt Foot Button to lock the Adjustable tilt
foot.
There is approximately 7 degrees of up and down adjustment for
the front of the projector.
Adjusting the height of a projected image or changing projection 3
angle will run the Auto Keystone correction function to quickly
correct the vertical distortion. The "Keystone" screen will be
displayed.
For operating the "Keystone" screen, see " Correcting Key- 4
stone Distortion" on page 33.
NOTE: Your "Keystone" correction data can be reset by pressing and holding the
3D REFORM button for a minimum of 2 seconds.
The rear foot height can be changed. Rotate the rear foot to the
desired height, but the vertical distance from the bottom to the
desk or floor should be 1 (25mm) to make the projector horizon- Up
tal on the flat surface.
Up
Down
CAUTION
Do not use the tilt-foot for purposes other than originally intended. Down
Misuses such as gripping the tilt-foot or hanging on the wall can cause
damage to the projector.
31
Zoom
Use the ZOOM lever to finely adjust the image size on the
screen.
Focus
Use the FOCUS ring to obtain the best focus.
32
Correcting Keystone Distortion

Auto Keystone Correction
The Auto Keystone correction feature will correct vertical distortion of a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
Manual Keystone Correction

You can also correct keystone distortion manually.
To do so:
1. Extend the Adjustable Tilt Foot to adjust the height of a projected

image. See page 31.
The Keystone screen will be displayed on the screen.
If the Keystone screen disappears, press the 3D REFORM button
once to display the Keystone screen again.
Projected area
2. Align the left (or right) side of the screen with the left (or right) Screen frame
side of the projected image.
Use the shorter side of the projected image as the base.
In the right example, use the left side as the base.
NOTE: When "Manual" is selected in "Keystone" from the menu, project an image
adjusting projector position so that the screen is smaller than the area of the
projected image. See page 90 for selecting "Manual" in "Keystone".
Align left side
3. Use the SELECT or button to adjust Horizontal.

Perform the keystone correction.
4. If the right and left sides of the projected image are not parallel to
each other, use the SELECT button to select Vertical and use
the SELECT button.
Fine adjust so that both sides are parallel to each other.
33
5. Repeat steps 3 and 4 to correct keystone distortion.
6. After completing Keystone correction, press the ENTER button.

The Keystone screen will disappear.
To perform Keystone correction again, press the 3D REFORM button

to display the Keystone screen and repeat above steps 1 to 6.
NOTE:
Turning on the projector will reset the previous correction setting values and correct distortion anew if the projection angle is
changed from the last use.
If the projection angle is the same as in the last use, the previous correction setting values are retained in the memory.
To use the previous correction setting values after changing projection angle, select "Manual" in "Keystone" from the menu. See
page 90.
To reset the 3D Reform correction setting values, press and hold the 3D REFORM button for a minimum of 2 seconds.
Each time the 3D REFORM button is pressed, the item will change as follows: Keystone Cornerstone None Keystone
...
For information on Cornerstone, see Correcting Horizontal and Vertical Keystone Distortion (Cornerstone) on page 43.
34
Optimizing an RGB Image Automatically

Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
R -C L I C K
VIDEO COMPUTER LAN

MEN U
1
S-VIDEO VIEWER
2
SOURCE AUTO ADJUST PIC-MUTE AUTO ADJ. SLIDE
SELECT
LAMP
VOLUME HELP
STATUS
EN
T ER IT 3D REFORM ON/STAND BY POWER ASPECT PICTURE
EX
[Normal picture] FREEZE 3D REFORM

PC CARD
Press the Auto Adjust button to fine-tune the computer image or to remove any vertical banding that might appear and
to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmer-
ing). This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This function also
adjusts the clock phase to reduce video noise, dot interference or cross talk.
This adjustment may be necessary when you connect your computer for the first time.
NOTE:
Some signals may not be displayed correctly or take time.
The Auto Adjust function does not work for component or video signals.
If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually. See page 86.
Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT
jack (Stereo mini) on the projector can be adjusted.
NOTE: When no menus appear, the SELECT buttons

R -C L I C K
VIDEO COMPUTER LAN
on the projector cabinet work as a volume control. S-VIDEO

1
VIEWER
2
Increase volume VOLUME HELP
ASPECT PICTURE
FREEZE 3D REFORM
Decrease volume
35
Using the Laser Pointer

You can use the laser to draw your audience's attention to a red dot that you can place on any object.
CAUTION:
Do not look into the laser pointer while it is on.
Do not point the laser beam at a person.
Do not allow children to use the laser pointer.
Press and hold the LASER button to activate the laser pointer.
LA
SE
R
To disable the laser pointer, set the function switch to Off.

Decide whether to enable or disable the laser, then set the switch as necessary using the tip of a thin ball-point pen.
On this model, the other selector switch is not used.
ON Laser enable/disable
switch
OFF Not used
On: Enabled (the laser lights when the LASER button is pressed) [Factory default]
Off: Disabled (the laser does not light even when the LASER button is pressed)
Disable the laser when using in an environment in which the unit is accessible to children.
36
Turning off the Projector

To turn off the projector:
1. Press the POWER (ON/STAND BY) button on the projector OFF
POWER
ON
cabinet or the POWER OFF button on the remote control. ME N U

MAGNIFY
LASER
PAGE
UP
The "Power Off / Are you sure?" message will appear. SOURCE AUTO ADJUST
POINTER
DOWN
SELECT
LAMP
MEN U
STATUS
EN
EX
EN T E R
E XI T
PC CARD
R -C L I C K
2. Press the ENTER button or the POWER (ON/STANDBY) or OFF

POWER
ON
ME N U
the POWER OFF button again.

LASER
MAGNIFY PAGE
UP
POINTER
The power indicator will glow orange. After the projector turns SELECT
SOURCE AUTO ADJUST
DOWN
LAMP
off, the cooling fans keep operating for 90 seconds (Cooling-off EN

STATUS
MEN U

EX
time).
EN T E R
E XI T
PC CARD
NOTE: Immediately after turning on the projector and displaying an

image, you cannot turn off the projector for 60 seconds. R -C L I C K
3. Turn off the Main Power switch. The power indicator will go
out.
CAUTION
Do not unplug the power cable from the wall outlet or do
not turn off the main power under any one of the following
circumstances.
Doing so can cause damage to the projector or PC card:
While the projector lamp is lighted.
While the cooling fans are running. (The cooling fans
continue to work for 90 seconds after the projector is turned
off).
While the PC CARD Access Indicator lights. Doing so can
damage your PC memory card.
After Use
Preparation: Make sure that the main power is turned off.
1. Unplug the power cable.

2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.
4. Cover the lens with the lens cap.
5. Put the projector and its accessories in the supplied soft case.
NOTE: Before putting the projector in the soft case, be sure to retract the feet. Failure to do so may cause the damage to the
projector.
37
4
Convenient Features
Turning Off the Image and Sound .............................. 39

Freezing a Picture...................................................... 39
Using the Pointer ....................................................... 39
Enlarging and Moving a Picture ................................. 40
Getting Integrated Help ............................................. 40
Using a USB Mouse .................................................. 41
Using Remote Mouse Receiver ................................. 42
Correcting Horizontal and
Vertical Keystone Distortion (Cornerstone) ........... 43
Making Freehand Drawings
on a Projected Image (ChalkBoard) ...................... 46
Storing Images Displayed on the Projector
on the PC card or USB Memory (Capture) ............ 47
Preventing Unauthorized Use of the Projector .......... 48
Using a USB Memory Device or
USB Memory Card Reader .................................... 53
Operation Using an HTTP Browser ........................... 54
Using the Projector to Operate a Computer Connected
on a Network (Desktop Control Utility 1.0) ............ 57
38
4. Convenient Features
Turning Off the Image and Sound R -C L I C K
VIDEO COMPUTER LAN

Press the PIC-MUTE button to turn off the image and sound for a short period of time. S-VIDEO
1
VIEWER
Press again to restore the image and sound. PIC-MUTE

2
AUTO ADJ. SLIDE
VOLUME HELP
ASPECT PICTURE
FREEZE 3D REFORM
Freezing a Picture VIDEO

R -C L I C K
COMPUTER LAN
1
Press the FREEZE button to freeze a picture. Press again to resume motion. S-VIDEO
2
VIEWER
NOTE: Pressing the MENU button will display the Capture menu that allows you to capture a VOLUME HELP
freezed image. See page 47 for more information. ASPECT PICTURE
FREEZE 3D REFORM
Using the Pointer

You can use one of nine pointers to draw your
audience's attention to the portion of a projected im- OFF
POWER
LASER
ON
MAGNIFY PAGE
age you want. POINTER
UP
DOWN
NOTE: You can select one pointer from the menu. See page MEN U
111.
EN T E R
E XI T
Press the POINTER button to display the pointer. Press the Pointer button to
display the pointer.
Use the SELECT button to move the pointer.

Press the POINTER button again. The pointer will dis-
OFF ON
POWER
LASER
MAGNIFY PAGE
appear. POINTER
UP
DOWN
MEN U
EN T E R
E XI T
R -C L I C K
Use the Select button to

move the pointer.
39
Enlarging and Moving a Picture

You can enlarge the area you want up to 400 percent.
To do so:
1. Press the POINTER button to display the

pointer. OFF
POWER
LASER
ON
MAGNIFY PAGE
UP
POINTER
DOWN
MEN U
EN T E R
E XI T
2. Move the pointer to the area you want to
OFF ON
enlarge. MAGNIFY
POWER
LASER
PAGE
UP
POINTER
DOWN
MEN U
EN T E R
E XI T
R -C L I C K
3. Enlarge the selected area. OFF

POWER
ON
LASER
When the MAGNIFY (+) button is pressed, the MAGNIFY
POINTER
PAGE
UP
image is magnified and the magnify icon will DOWN
be displayed. To magnify the selected area, MEN U
use the SELECT button to move the
EN T E R
E XI T
magnify icon and press the MAGNIFY (+)
button. R -C L I C K
4. Return the image to the original size. OFF ON

POWER
Press the MAGNIFY (-) button until the mag- MAGNIFY

LASER
PAGE
UP
nify icon changes to the pointer. POINTER
DOWN
MEN U
EN T E R
E XI T
R -C LI C K
Getting Integrated Help R -C L I C K

OFF
POWER
ON
VIDEO COMPUTER LAN

LASER
You get the contents about Help in English, German and MAGNIFY PAGE
1
S-VIDEO VIEWER UP
POINTER
2
Japanese. PIC-MUTE AUTO ADJ. SLIDE DOWN
VOLUME HELP MEN U
ASPECT PICTURE
EN T E R
E XI T
FREEZE 3D REFORM
R -C L I C K
Display Help Exit Help
40
Using a USB Mouse USB

Using a USB mouse gives you a smooth operation. A commercially AUDIO OUT
available USB mouse can be used. PC CARD

R AUDIO IN L VIDEO IN
LAN USB
S-VIDEO IN PC CONTROL COMPUTER 1 IN AUDIO IN COMPUTER 2 IN MONITOR OUT
AC IN
NOTE: There may be some brands of a USB mouse that the projector does
not support.
Operate the Menus using the USB mouse

Mouse Cursor
When connecting a USB mouse to the projector, you get a mouse cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse cursor disappears.
NOTE: You can change the shape of the mouse cursor. To do so, select the menu Setup Tools Mouse Mouse
Pointer
Menu Display
Clicking with the right mouse button displays the menu.
To close the menu, click anywhere in the background.
Adjusting and Setting Display

You can select a menu item and click with the left mouse button to make adjustments and settings.
Using the middle button on the mouse

The projector supports the middle button on your mouse.
With the middle button you can do the following:
You can use a scroll bar in the menu or the help.
You can click the middle button to display or hide the Chalkboard toolbar.
Example:
Click (or press and hold) the left mouse button on the or to adjust the brightness. Or click and drag the left
mouse button on the slide bar horizontally to adjust it.
To save the adjustments, click . The display is closed.
Click with the left mouse button to display a description of the selected menu item.
Click and drag the title bar with the left mouse button to move the adjustment or setting dialog box.
41
Using Remote Mouse Receiver

The remote mouse receiver enables you to operate your computers mouse functions from the remote control. It is a
great convenience for your computer-generated presentations.
Connecting the remote mouse receiver to your computer

If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computers USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
Computer
Remote mouse receiver
To USB port of PC or Macintosh
When operating a computer via the remote mouse receiver

7m/22 feet
30
30
Remote sensor on the

remote mouse receiver
When connecting using the USB port

For PC, the mouse receiver can only be used with a Windows 98/Me/XP* or Windows 2000 operating system.
* NOTE: In Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may
not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.
Operating your computers mouse from the remote control

You can operate your computer's mouse from the remote control.
PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint
on your computer.
Select Button: moves the mouse cursor on your computer.
MOUSE L-CLICK Button: works as the mouse left button.
MOUSE R-CLICK Button: works as the mouse right button.
NOTE: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the
user documentation or online help supplied with your computer.
42
Correcting Horizontal and Vertical Keystone Distortion (Cor-

nerstone)
Use the 3D Reform feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right
side of the screen longer or shorter so that the projected image is rectangular.
Cornerstone
1. Press and hold the 3D REFORM button for a minimum of 2 seconds to reset current adjustments.
Current adjusments for Keystone or Cornerstone will be cleared.
2. Project an image so that the screen is smaller than the area of the raster.
3. Pick up any one of the corners and align the corner of the image with a corner of the screen.
Projected image
The drawing shows the

upper right corner.
Screen
4. Press the 3D REFORM button on the remote control twice.

The Cornerstone adjustment screen is displayed.
5. Use the SELECT button to select one icon which points in the direction you wish to move the
projected image frame.
6. Press the ENTER button.
7. Use the SELECT button to move the projected image frame as shown on the example.
Screen
43
Screen
9. Use the SELECT button to select another icon which points in the direction.
On the Cornerstone adjustment screen, select Exit or press the EXIT button on the remote control.
Screen
The confirmation screen is displayed.
10.Press the SELECT or button to highlight the [OK] and press the ENTER button.
This completes the keystone correction.

Selecting Cancel will return to the adjustment screen without saving changes (Step 3).
Selecting "Reset" will return to the factory default.
Selecting "Undo" will exit without saving changes.
NOTE: To reset the 3D Reform correction setting values, press and hold the 3D REFORM button for a minimum of 2 seconds.
NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be available. Should this happen, first reset the 3D
Reform data and then do each setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/or Screen setting
can limit 3D Reform in its adjustable range.
44
The adjustable ranges for 3D Reform are as follows:
Horizontal Vertical
Cornerstone Max. +/ 35 approx.
Keystone LT265: Max. +/ 35 approx. Max. +/ 40 approx.
LT245: Max. +/ 30 approx.
* The following are conditions under which the maximum angle is achived:
Image is projected in Wide (Zoom lever)
Resolution is XGA
Higher resolution than XGA narrows the adjustable range.
Menu items should be set as follows:
Aspect Ratio ........... 4:3
Screen Type ........... 4:3
Horizontal and Vertical are adjusted separately.
A combination of both adjustments narrows the adjustable range.
When "4:3 Fill" is selected in Aspect Ratio, "Cornerstone" and "Horizontal Keystone" are not available.
NOTE:
If the Cornerstone screen is unavailable (grayed), press and hold the 3D REFORM button for a minimum of 2 seconds to reset
the current correction data. The Cornerstone function becomes available.
Turning on the projector will reset the previous correction setting values and correct distortion anew if the projection angle is
changed from the last use.
If the projection angle is the same as in the last use, the previous correction setting values are retained in the memory.
To use the previous correction setting values after changing projection angle, select "Manual" in "Keystone" from the menu. See
page 90.
NOTE: The 3D Reform feature can cause an image to be slightly blurred because the correction is made electronically.
45
Making Freehand Drawings on a Projected Image

(ChalkBoard)
The ChalkBoard feature allows you to write and draw messages on a projected image.
NOTE: The ChalkBoard feature is available only when a USB mouse is used.
To display the ChalkBoard tool bar, click the middle button on your mouse or select "ChalkBoard" from the menu.
The tool bar contains the following icons.
Drag ................. Drags to move the tool bar.

Pen ................... Left-click and drag to draw. Left-click or right-click the pen icon to display the pen palette containing four
lines of different thickness from which you can select a line you prefer by left-clicking.
Color ................ Selects a color. Left-click to display the color palette from which you can select a color you prefer by left-
clicking.
Capture ............. Left-click to capture a drawing on the ChalkBoard screen and save it to your PC-card inserted into the PC
card slot of the projector.
Eraser ............... Left-click and drag to erase part of a drawing. Left-click or right-click the eraser icon to display the eraser
palette containing four erasers of different thickness from which you can select an eraser you prefer by left-
clicking.
Clear ................. Left-click to clear the drawing completely from the ChalkBoard screen.
Hide .................. Hides the tool bar by left-clicking. Right-clicking anywhere on the screen displays the ChalkBoard tool bar
again.
Exit ................... Clears the complete drawing and exits the ChalkBoard.
NOTE:
The menu is not available while you display the ChalkBoard screen.
Selecting another source or switching slides in the Viewer clears a drawing completely.
46
Storing Images Displayed on the Projector on the PC card or

USB memory (Capture)
The Capture features allows you to capture an image from a source that is currently being displayed. The image is
saved as JPEG in the PC card or USB memory.
NOTE:
Unless a PC card or USB memory is inserted into the PC Card slot or USB port of the projector, the Capture feature is not
available.
The "Card Error" display means that the free space of the PC card or USB memory is insufficient for saving images. Make more
space available on the card by erasing unwanted images with your PC. The number of images that can be captured depends on
the size of the PC card.
Be sure not to turn off the power or remove the PC card or USB memory while capturing an image. Doing so could cause a
loss of the data in the PC card or USB memory or damage to the card itself.
Preparations:
Insert the PC card into the PC card slot or USB memory into USB port of the projector.
Insert the PC card so that the end with the insertion direction arrow on the top goes in first.
* Press the eject button to eject the card.
1. Project the image you wish to store on the projector.

2. Press the FREEZE button on the remote contorol.
3. Press the MENU button to display the Capture menu.
Capture .................. Captures an image and save it as a JPEG file in a PC card or USB memory.
Drive ...................... Select the PC Card or USB memory. You can capture an image and save it to your PC card or USB memory.
Exit ........................ Exits the Capture function. Another option to exit the Capture function is to press the MENU or EXIT button
on the remote control or projector cabinet.
NOTE:
Captured images with higher resolution than the projector's native resolution cannot be displayed correctly.
File size of the captured image varies depending on the resolution of an input signal.
An hourglass indicating that an image is being captured appears on the projector's display. Do not eject the PC card or turn off
the projector's power while this icon is displayed. Doing so will damage the PC card data. If the PC card data is damaged, use a
computer to repair the data.
47
Preventing Unauthorized Use of the Projector

Assigning a keyword prevents the projector from being used by unauthorized individuals.
Assigning a Keyword for the first time

1. Press the MENU button.
The menu will be displayed.
2. Press the SELECT button to highlight the Setup submenu and press the ENTER button.
The page tab Basic will be highlighted.
3. Press the SELECT button twice to highlight the page tab Security.
48
4. Press the SELECT button four times to highlight Security.
5. Press the ENTER button to display the Security screen.
6. Press the ENTER button once to highlight the Keyword entry box and press the ENTER button.
The Software keyboard will be displayed.
49
7. Enter an alphanumeric keyword using the Software keyboard
For example, to enter 1234, follow the steps 7-1 to 7-4 below.
NOTE:
Please make a note of your keyword.
Do not use spaces (SP) in your keyword.
7-1. Highlight the number 1 and press the ENTER button.

The asterisk will be displayed in the Keyword entry box.
7-2. Press the SELECT button once to highlight 2 and press the ENTER button.
7-3. For 3 and 4, use the same procedure as step 7-2.
7-4. Press the SELECT button to highlight OK and press the ENTER button.
The Software keyboard will disappear.
8. Press the SELECT button once to highlight Disable and press the SELECT button to highlight
Enable.
9. Press the SELECT button to highlight OK and press the ENTER button.
The confirmation screen will be displayed.
10.Press the ENTER button.

The Security Function is now enabled.
NOTE: A PC card can be used as a protect key. You can skip the keyword entry by inserting a registered PC card when turning on
the projector. See page 96.
50
Checking If Security is enabled

Turn off the projector and turn it back on to check if the Security function is enabled.
1. Press the POWER (ON/STANDBY) button.

The "Power Off / Are you sure?" message will appear.
Press the ENTER button or the POWER (ON/STANDBY) or the POWER OFF button again.
The lamp lights off and the POWER indicator flashes orange. Please wait until the POWER indicator changes
from flashing to steady light.
2. When the POWER indicator lights steady orange, push the Main POWER switch to the off position (O).
The projector will turn off.
3. Push the Main POWER switch to the on position (I).

The POWER indicator lights orange. The projector is in standby condition.
4. Press and hold the POWER (ON/STANDBY) button for a minimum of two seconds.
The projector will turn on. The Projector is locked! Enter your keyword. message will be displayed at the bottom
of the screen.

The Keyword entry screen will be displayed

7. Use the same procedures as steps 1 to 7 described in the Assigning a Keyword for the first time
section to enter 1234.
Each time one number is entered, an (asterisk) will appear. Keyword appears as asterisks so the real
keyword is hidden.
8. After entering your keyword, highlight OK and press the ENTER button.
The Software keyboard will disappear. This will allow you to operate the projector.
51
Disabling the Security

The on-screen menu will be displayed.
NOTE: Immediately after the projector has been turned on and the Projector is locked! Enter your keyword. message is
displayed at the bottom of the screen, pressing the MENU button will display the Keyword entry will be displayed. At this
time, pressing the MENU button will display the on-screen menu.
2. Press the SELECT button to highlight Setup and press the ENTER button.
The page tab Basic will be highlighted.
3. Press the SELECT button twice to highlight the page tab Security.
4. Press the SELECT button four times to highlight Security and press the ENTER button.
The Keyword entry screen will be displayed

6. Use the same procedures as steps 1 to 7 described in the Assigning a Keyword for the first time
section to enter 1234.
Each time one number is entered, an (asterisk) will appear. Keyword appears as asterisks so the real
keyword is hidden.
7. After entering your keyword, highlight OK and press the ENTER button.
The Software keyboard will disappear. The Security screen will be displayed.
8. Highlight Enable and press the SELECT button to highlight Disable.
9. Press the SELECT button to highlight OK and press the ENTER button.
The Security Function is now disabled.
NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code.
52
Using a USB Memory Device or USB Memory Card Reader

The projector is compatible with either a USB memory device or
USB memory card reader which supports the viewer and security
features.
To use a USB memory device or USB memory card reader,

connect the device to the USB port (type A).
Select one of the drive icons for your USB memory in a pane
on the left side of the Viewer window.
To use a USB memory device as a Protect key for Security
function, select one from the Drive icons in the Security setting
AUDIO OUT
PC CARD LAN USB

screen. See page 95.

AC IN
NOTE:
Some USB memory devices (brands) or USB memory card readers may not work.
The projector does not support NTFS formatted flash memory card or USB memory device.
To format your flash memory card or USB memory device in your computer, refer to the document or help file that comes with
your Windows.
You cannot use a USB memory device and a USB memory card reader when connecting a USB mouse to the projector.
Do not do the following while the USB memory device or USB memory card readers access indicator is lit or flashing (while
data is being accessed.) Doing so can damage your USB memory device or USB memory card reader in the reader. Back up
your data in case it will need to be restored.
* Pulling out the USB memory device or USB memory card reader from the USB port of the projector.
* Pulling out the memory card from the USB memory card reader
* Turning off the main power switch or unplugging the power cable.
The drive for USB 1-4 is displayed only when the USB memory device or USB memory card reader is connected to the
projector. The drive for USB 1-4 may be displayed differently from the one in the USB memory card reader.
Some USB memory devices (brands) or USB memory card readers cannot be used as Protect key for the projectors Security
function.
CAUTION: Do not insert a USB memory device or USB memory card reader into the LAN port (RJ-45). Doing so
can cause damage to the LAN port (RJ-45).
53
Operation Using an HTTP Browser

Overview
The use of HTTP server functions will allow control of the projector from a web browser without the installation of
special software. Please be sure to use Microsoft Internet Explorer 4.x or a higher version for the web browser. (This
device uses JavaScript and Cookies and the browser should be set to accept these functions. The setting method
will vary depending on the version of browser. Please refer to the help files and the other information provided in your
software.)
NOTE:
* The displays or buttons response can be slowed down or operation may not be accepted depending the settings of your
network. Should this happen, consult your network administrator.
* The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and
repeat. If you still cant get any response, turn off and back on the projector.
Access is gained to the HTTP server functions by specifying
http:// <the projectors IP address> /index.html
in the entry column of the URL.
CAUTION:
Do not use the HTTP Server functions and PC Control Utility 3.0 included on the supplied CD-ROM. Using both at
the same time may result in a connection failure or slow response.
Preparation Before Use

Make network connections and set up the projector and confirm that it is complete before engaging in browser opera-
tions. (See Setting LAN Mode on page 99.)
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the
setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set
will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be
reflected in operation. It is recommended that a proxy server not be used unless it is unavoidable.
Handling of the Address for Operation via a Browser

Regarding the actual address that is entered for the address or entered to the URL column when operation of the
projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of
the projector has been registered to the domain name server by a network administrator, or the host name corre-
sponding to the IP address of the projector has been set in the HOSTS file of the computer being used.
Example 1: When the host name of the projector has been set to pj.nec.co.jp,
http://pj.nec.co.jp/index.html
is specified for the address or the entry column of the URL.
Example 2: When the IP address of the projector is 192.168.73.1, access is gained to the
HTTP server functions by specifying
http://192.168.73.1/index.html
for the address or the entry column of the URL.
54
Structure of the HTTP Server
Power: This controls the power of the projector.

On ................... Power is switched on.
Off ................... Power is switched off.
Volume: This controls the volume of the projector.

..................... Increases the volume adjustment value.
..................... Decreases the volume adjustment value.
Mute: This controls the mute function of the projector.

Picture On ....... Mutes the video.
Picture Off ....... Cancels the video muting.
Sound On ........ Mutes the audio.
Sound Off ........ Cancels the audio muting.
OSD On .......... Mutes the on-screen display.
OSD Off .......... Cancels the muting of the on-screen display.
All On .............. Mutes each of the video, audio, and on-screen display functions.
All Off .............. Cancels the muting of each of the video, audio, and on-screen display functions.
Picture: Controls the video adjustment of the projector.

Brightness ... Increases the brightness adjustment value.
Brightness ... Decreases the brightness adjustment value.
Contrast ...... Increases the contrast adjustment value.
Contrast ...... Decreases the contrast adjustment value.
Color ........... Increases the color adjustment value.
Color ........... Decreases the color adjustment value.
Hue ............. Increases the hue adjustment value.
Hue ............. Decreases the hue adjustment value.
Sharpness ... Increases the sharpness adjustment value.
Sharpness ... Decreases the sharpness adjustment value.
The functions that can be controlled will vary depending on the signal being input to the projector.
55
Source Select: This switches the input connector of the projector.
Computer1 ...... Switches to the COMPUTER 1 IN connector.
Computer2 ...... Switches to the COMPUTER 2 IN connector.
Video ............... Switches to the VIDEO IN connector.
S-Video ........... Switches to the S-VIDEO IN connector.
Viewer ............. Switches to the Viewer.
LAN ................. Switches to a LAN signal.
Projector Status: This displays the condition of the projector.

Remaining Lamp Time ... Displays the remaining life of the lamp as a percentage.
Lamp Hour Meter ........ Displays how many hours the lamp has been used.
Projector Usage .......... Displays how many hours the projector has been used.
Error Status ................. Displays the status of errors occurring within the projector.
Refresh ....................... Updates the display of the following conditions.
56
Using the Projector to Operate a Computer Connected on a

Network (Desktop Control Utility 1.0)
When Desktop Control Utility 1.0 on the included User Supportware 2 CD-ROM is installed on the computer, that
computer can be operated using the projector over a network.
For example, say you have a PowerPoint file on a computer in your office that you want to use for a presentation at a
meeting. If the computer in the office is connected by LAN to the projector in the meeting room, the projector can be
operated to project the image of the desktop of the computer (Windows 2000 or XP) in the office and display the
PowerPoint file during the meeting. This eliminates the need for taking the computer from the office to the meeting
room.
Meeting room
Office
Disclaimer
You can use the Desktop Control Utility 1.0 to operate a computer located in a separate room from the projector over
a network. This means there might be potential security risks that you may be exposed to which could cause damage
by unauthorized access or illegal use. We recommend you take some measures to prevent third parties from unautho-
rized access to your data or information.
We share neither liability nor responsibility to any loss or damages arising from information leak or power down
without notice.
NOTE: In Windows operating system, click Control Panel Power Options System Standby Never. This will
disconnect a LAN connection when the computer goes in standby mode.
NOTE: To use the Desktop Control Utility 1.0, you need to have a USB mouse inserted into the USB port of the projector.
57
Operations on the Computer

1. Connect the computer to the LAN and make the required settings.
2. Install Desktop Control Utility 1.0 on the computer.
For instructions on installation, refer to the included NEC Software Utility Installation Guide.
For instructions on operating the software, see the Desktop Control Utility 1.0s help file.
3. Prepare the documents to be presented at the meeting and save them on the computer.
4. Start up Desktop Control Utility 1.0.
The Startup password window appears.
Window at the first startup Window after entering your startup password
Important:
Your startup password will be required each
time you start Desktop Control Utility 1.0.
If you forget or lost your startup password,
5. Input the startup password and click OK. install the program again.
The Current password input window appears.
NOTE: The "Current password" will be changed each time you start Desktop Control Utility 1.0.
6. Make a note of the password.

7. Click OK.
Desktop Control Utility 1.0 starts.
Go to the room where the projector is installed, taking the password you made a note in the previous Step [6].
58
Operations on the projector Connecting to the computer

1. Make the LAN settings on the projector.
Make the LAN settings at [Setup] [Installation] [LAN Mode] in the menu. (See page 99)
2. Connect a commercially available USB mouse to the projector. (See page 41)
3. Click anywhere on the screen with the USB mouse.
The menu appears.
4. Click Source, then click LAN.
The help message is displayed.
The message is displayed only when a password for Desktop Control Utility 1.0 is not assigned.
5. Follow the message to press the MENU button on the projector cabinet or the remote control.
The connections bar appears at the bottom left of the screen.
6. Click the password input icon .

7. Click Entry.
The password input window appears.
8. Click .
The character input window appears. (See page 132.)
59
9. Input the password you made a note of in the previous Step [6] in Operations on the Computer.
10. Input the password and click OK.
The password input window is turned off.
11. Click the PC search icon .
The PC search window appears.
12. Click OK.

The connection selection window appears.
To search by inputting the IP address of the connected computer, click on the PC Search window, click
Input IP Address, then click OK.
13. Click the computer to which you want to connect, then click OK.
The desktop of the connected computer appears.
NOTE: Once the desktop appears, the menu will no longer appear when the USB mouse is clicked. To display the menu while the
desktop is displayed, press the button on the projector itself or on the remote control.
Operations on the projector Operating the desktop

A USB mouse connected to the projector can be used to operate the displayed desktop.
If the MENU button on the projector cabinet or the remote control is pressed while the desktop is displayed, an
additional operations bar appears at the bottom left of the screen.

60
The following operations are available only with buttons on the projector cabinet or the remote control.
Disconnect icon ................. Use to cut off communications with the computer.
Shift icon ............................ Select this icon and press the ENTER button to set the shift lock mode. Select this icon and
press the ENTER button again to cancel the shift lock mode.
Ctrl icon ............................. Select this icon and press the ENTER button to set the control lock mode. Select this icon
and press the ENTER button again to cancel the control lock mode.
Esc icon ............................. Use to do the same operation as when the Esc button on the computer is pressed. Use it
for example to stop a PowerPoint slideshow.
Operations on the projector Disconnecting communication

1. Press the MENU button while the desktop is displayed.
The additional operations bar appears at the bottom left of the screen.
2. Select the disconnect icon and press the ENTER button.

To reconnect the communication, click the PC search icon and repeat steps 12 and 13 in the previous page.
NOTE: Disconnection is possible by clicking the projector icon and then "Disconnect" on the task bar.
Operations on the projector Exiting the desktop operation

Exiting the desktop operation using the taskbar in Windows.
1. Click the projector icon on the taskbar while the desktop is displayed.
The pop-up menu appears.
2. Click Exit.
Desktop Control Utility 1.0 quits
3. Click anywhere on the screen.
4. Click again anywhere on the screen.
The menu appears.
5. Click "Source" and then click any other source than "LAN".
The menu turns off.
61
5
Using the Viewer
Making the Most out of the Viewer Function .............. 63
Operating the Viewer Function from

the Projector (playback) ......................................... 64
Changing Background Logo ...................................... 70
62
5. Using the Viewer
Making the Most out of the Viewer Function

Features
You can view presentation data, capture and play images on the projector. A PC card is used to view presentation data
prepared on the computer and to capture and play images projected with the projector.
The Viewer feature allows you to view slides stored on a PC memory card (referred to as PC card in this manual) or
USB memory on the projector. Even if no computer is available, presentations can be conducted simply with the
projector. This feature is convenient for holding presentations at meetings and in offices, as well as for playing images
taken on digital cameras.
NOTE:
To use the Viewer, first you need to create presentation materials on your PC (JPEG, BMP, GIF*1, PNG*1, Index*2 files).
For creating presentation materials using the Ulead Photo Explore 8.0, see the supplied "NEC Software Utility Installation Guide"
or On-line help in Ulead Photo Explorer 8.0.
*1 Both PNG and GIF format support non-interlaced images only.
*2 Index file is a file created using the Ulead Photo Explore 8.0 contained on the supplied NEC User Supportware 2 CD-ROM.
See the suppliedNEC Software Utility Installation Guide for installing the Ulead Photo Explore 8.0 on your computer.
Easy to use
Presentations can be started immediately simply by inserting a PC card or USB memory (not supplied)
Easy slide switching
Remote control operation
Jumping to a list of slides or any specific slide
Simple utility software (for computer)

Ulead Photo Explore 8.0SE Basic operable on Windows XP/Windows 2000.
Slides can be created by capturing the currently displayed image.
Control screen for displaying lists of slides and editing.
* Microsoft, Windows and PowerPoint are registered trademarks of Microsoft Corporation.
63
5. Using the Viewer
Operating the Viewer Function from the Projector (playback)

This section describes the operation for showing slides created using the Viewer function with the projector. It is also
possible to make slides directly from the images projected with the projector.
Projecting slides (Viewer)

Preparation: Use the Capture feature to store graphic files (JPEG, BMP, non-interlaced GIF or non-interlaced PNG
files) in a PC card or USB memory inserted into the projectors slot. Or store JPEG or BMP files in a PC card or USB
memory inserted into your PC.
1. Insert a PC card into the PC card slot or USB memory into the USB port of the projector.
2. Press the VIEWER button on the remote control or select the Viewer from the source list.
An image stored in the PC card or USB memory will be displayed.
3. Press the MENU button to display the Viewer menu.
The Viewer menu will appear when you press the MENU button on the remote control or the projector cabinet.
The Viewer menu includes the following commands:
Play ................... Plays back automatically or manually depending on the setting in Options. This allows you to move on to the
next slide when "Manual Play" is selected in the Play Mode.
Stop ................... This allows you to stop Auto Play while you are playing back and to resume playing from the selected slide
or folder when "Auto Play" is selected in the Play Mode.
Thumbnails ........ Displays a list of thumbnails of Graphic files stored in the PC card inserted into the projector.
Delete ................ Deletes a captured slide(s) or all the captured slides in the Capture - specific folder.
Logo .................. Replace the default background logo with another logo in JPEG, BMP, non-interlaced GIF or non-interlaced
PNG format.
Options .............. Displays the Viewer setting options.
4. Select Play and then press the ENTER button to display the first slide or to start playing slides auto-
matically.
64
5. Using the Viewer
Viewer Window Elements

Number of files Thumbnail/file name
Highlight
Slot 1 3 Fichiers ?
_CAP_
List of folders _RESTORE
RECYCLED
0000.jpg 0001.jpg 0002.jpg
Scroll bar
Cursor (orange)
Information 1/3 0000.jpg 60KB

slection : ENTER
Highlight .................................. Indicates the selected folder or drive.

List of folders .......................... Indicates folders contained on a PC card or USB memory.
Information .............................. Indicates information of the selected file or folder.
Folder: folder name, creation date (month/day/year), creation time (hour/minute).
File: slide number/number of displayable slides in a folder, file name, creation date (month/day/
year), creation time (hour/minute), file size.
Number of files ........................ Indicates number of displayable slides in the selected folder. The maximum number of images
recognized as slides within one directory is about 1000.
Thumbnail/file name ................ Indicates thumbnails and names contained in a folder.
Cursor ..................................... Indicates the selected slide.
Scroll bar ................................. Used to view folders or files not visible in the window.
65
5. Using the Viewer
Setting Option for Viewer
Play Mode:
Manual .................. Views a slide manually when the Viewer source is selected.
Auto ...................... Plays back slides automatically when the Viewer source is selected.
Interval:
Specifies interval time between 5 and 300 seconds.
Start:
Specifies start screen when the Viewer source is selected.
Show Thumbnails:
Selecting the Viewer source will display a list of thumbnails of graphic files stored in the PC card or USB memory
when On is selected.
Off On
? Slot 1 3 Fichiers ?
Slot 1 3 Fichiers
_CAP_ _CAP_
_RESTORE _RESTORE
RECYCLED RECYCLED
0000.jpg 0001.bmp 0002.jpg 0000.jpg 0001.jpg 0002.jpg
1/3 0000.jpg 60KB 1/3 0000.jpg 60KB

slection : ENTER dossier : EXIT slection : ENTER dossier : EXIT
Sort:
Rearranges the slides or thumbnails by name, extension, date or size.
NOTE: This setting is not available for the following folders:
* The "__CAP__" folder for captured images
* Folders created with the "Output Viewer" feature of Ulead Photo Explorer 8.0 or with Viewer PPT Converter 3.0
OK/Cancel:
To close the Options menu with saving changes, select "OK" and press the ENTER button.
To close the Options menu without saving changes, select "Cancel" and press the ENTER button.
66
5. Using the Viewer
Exiting Viewer
To exit Viewer, switch to another input such as Computer 1, Computer 2, Video, S-Video or LAN.
* To switch to another input, there are two ways:
* Press the COMPUTER 1, COMPUTER 2, VIDEO, S-VIDEO or LAN button on the remote control.
* Press the MENU button on the remote control to display the Viewer menu. Press the MENU button again to
display the main menu and select the input from the "Source" submenu.
With this function it is possible to switch directly to a slide when the picture of a VCR or computer is being projected.
Example: When conducting presentations using a combination of slides and moving pictures from a VCR, etc., it is
possible to switch from a Viewer slide to the video picture then back to the Viewer slide simply by using the Viewer
button.
NOTE: Even if you switch the current Viewer source to another source, the current slide is retained. When you return back to the
Viewer, you will get the slide that has been retained.
Viewing Digital Images

Digital images can be played with the Viewer if the following conditions are met:
If the image can be stored on an MS-DOS format PC card.

If the image can be stored in a format supported by the Viewer. With the Viewer, images on the card are
searched for in directories and images in JPEG, BMP, non-interlaced GIF or non-interlaced PNG format are
recognized as slides.
NOTE: The maximum number of images recognized as slides within one directory is about 1000.
67
5. Using the Viewer
Deleting Captured Images

Using the Delete command on the Viewer menu allows you to delete captured images.
To delete captured images:

Preparation: Make sure that the PC card is inserted into the PC card slot or USB memory into the USB port of the
projector.
1. Press the VIEWER button on the remote control to display an image.

3. Use the button to select Thumbnails and then press the ENTER button.
The Thumbnail screen will be displayed.
Slot 1 3 Fichiers ?
_CAP_
_RESTORE
RECYCLED
0000.jpg 0001.jpg 0002.jpg
1/3 0000.jpg 60KB

slection : ENTER dossier : EXIT
NOTE: To change highlight from the Thumbnails screen (pane on the right) to a directory tree (pane on the left) , press the EXIT
button. To return highlight to the Thumbnails screen, press the ENTER button.
4. Use the buttons to select an image you wish to delete.

6. Use the button to select Delete and then press the ENTER button.
A confirmation message will be displayed.
7. Use the button to select Yes and then press the ENTER button.
This completes deleting.
68
5. Using the Viewer
To delete all the captured images:
1. Repeat steps 1 to 3 in the above described procedure.

2. Press the EXIT button to select the __CAP__ folder in the directory (pane on the left).
Slot 1 3 Fichiers ?
__CAP__
_RESTORE
RECYCLED
0000.jpg 0001.jpg 0002.jpg
1/3 0000.jpg 60KB

4. Use the button to select Delete and then press the ENTER button.
A confirmation message will be displayed.
5. Use the button to select Yes and then press the ENTER button.
This completes deleting.
NOTE: The vacant "__CAP__" folder stays even after you delete all the captured images.
69
5. Using the Viewer
Changing Background Logo

You can change the default background logo using the Viewer feature.
NOTE: File size must be 256KB or less. File formats other than JPEG, BMP, non-interlaced GIF or non-interlaced PNG are not
available.
Preparation:
Use the Capture feature to store JPEG or BMP files in a PC card inserted into the projectors slot or USB memory
into projectors USB port. Or store JPEG, BMP, non-interlaced GIF or non-interlaced PNG files in a PC card or
USB memory inserted into your PCs slot or USB port and insert the PC card into the projectors slot or USB
memory into the projectors USB port.
1. Press the VIEWER button on the remote control to display an image.

3. Use the button to select Thumbnails and then press the ENTER button.
The Thumbnail screen will be displayed.
Slot 1 3 Fichiers ?
_CAP_
_RESTORE
RECYCLED
0000.jpg 0001.jpg 0002.jpg
1/3 0000.jpg 60KB

NOTE: To change highlight from the Thumbnails screen (right window) to a directory tree (left window) , press the EXIT button.
To return highlight to the Thumbnails screen, press the ENTER button.
4. Use button to select a file (slide) for your background logo.

6. Use the button to select "Logo" and then press the ENTER button.
A confirmation dialog box will be displayed.
7. Use the button to select Yes and press the ENTER button. This completes changing a logo for the
background.
* Once you have changed the background from the NEC logo to another, you cannot return the logo to back-
ground even by using Reset. To put the NEC logo back in the background logo, repeat the above steps. The
NEC logo file is included on the supplied User Supportware 2 CD-ROM (/Logo/nec_b_x.jpg).
70
6
Using On-Screen Menu
Using the Menus ........................................................ 72
Menu tree .................................................................. 73
Menu Elements .......................................................... 75
Menu Descriptions & Functions [Source] .................. 76
Menu Descriptions & Functions [Adjust] .................... 79
Menu Descriptions & Functions [Setup] .................... 90
Menu Descriptions & Functions [Information] .......... 112
Menu Descriptions & Functions [Reset] .................. 116
71
6. Using On-Screen Menu
Using the Menus

1. Press the MENU button on the remote control or the projector cabinet to display the menu.
Submenu window
Submenu
Main menu
Currently available
buttons
NOTE: The commands such as , ENTER, EXIT in the gray bar show available buttons for your operation.
2. Press the SELECT buttons on the remote control the projector cabinet to display the submenu.
3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the
first tab.
4. Use the SELECT buttons on the remote control or the projector cabinet to select the item you want
to adjust or set.
You can use the SELECT buttons on the remote control or the projector cabinet to select the tab you
want.
NOTE: You can select a tab only when the tab color is orange.
5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.
6. Adjust the level or turn the selected item on or off by using the SELECT buttons on the remote
control or the projector cabinet.
Changes are stored until you adjust it again.
7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the
projector cabinet to quit the menu display.
NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.
72
Menu tree Basic menu items are indicated by

shaded area.
Menu Item
Source Computer1, Computer2, Video, S-Video, Viewer, LAN, Entry List
Adjust Basic Brightness
Contrast
Color
Hue
Sharpness
Wall Color Off, Blackboard, Light yellow, Light green, Light blue, Sky blue, Light rose, Pink
Aspect Ratio 4:3 4:3, Letterbox, Wide Screen, Crop
16:9 4:3 Window, Letterbox, Wide Screen, 4:3 Fill
Volume
Reset
Picture Preset 1 to 5
Management Detail Settings Reference Presentation, Video, Movie,
Graphic, sRGB
Gamma Correction Dynamic, Natural, Black Detail
Color Temperature 5000, 6500, 7200, 7800, 8500, 9300
White Peaking
Black Expansion On, Off
White Balance Brightness RGB, Contrast RGB
Color Correction Red, Green, Blue,Yellow, Magenta,
Cyan, Color Gain
Signal Type RGB, Component
Video Filter Off, Less, More
Image Options Clock
Phase
Horizontal Position
Vertical Position
Blanking Top, Bottom, Left, Right
Resolution Auto, Native
Overscan 0%, 5%, 10%
Video Noise Reduction Off, Low, Medium, High
Color Matrix HDTV, SDTV
3D Y/C Separation Off, On
Vertical Enhancer Off, 1, 2, 3
I/P Converter Deinterlace(Auto/Still), Interlace
Setup Basic Keystone Auto, Manual
Cornerstone
Lamp mode Normal, Eco
Menu Mode Basic Menu, Advanced Menu
Language English, Deutsch, Franais, Italiano, Espaol, Svenska, Suomi, Norsk,
Nederlands, Trke, Polski, , , Magyar, Portugus,
Cestina , , Dansk, , ,
Menu Menu Color Select Color1 to 5, Monochrome
Display Select Source: On, Off / Message: On, Off
Menu Display Time Manual, Auto 5 sec, Auto 15 sec, Auto 45 sec
Background Blue, Black, Logo
Security Cabinet Button Unlock, Lock
Password (Menu) Entry, Delete
Password (Logo) Entry, Delete
Security Enable, Disable, Keyword, Use Protect Key, Drive, Read, Register, Delete
73
Menu Item
Setup Installation Orientation Desktop Front, Ceiling Rear, Desktop Rear, Ceiling Front
Screen Screen Type: 4:3, 16:9 / Position
LAN Mode Built-in
PC Card Advanced: Network Type, Wep
Domain
Mail
Projector Name
Communication Speed 4800, 9600, 19200, 38400
Options Auto Adjust Off, Normal, Fine
Auto Start Off, On
Power Management Off, On
Fan Mode Auto, High
Default Source Select Last, Auto, Select (Computer1/2, Video, S-Video, Viewer, LAN)
Signal Select Computer1 RGB/Component, RGB, Componet, Scart
Computer2 RGB/Component, RGB, Componet
Video Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
S-Video Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
OUT Terminal Last, Computer1, Computer2
Tools ChalkBoard
Off Timer Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00
Mouse Mouse Pointer: Pointer 1 to 9 / Button: Right Hand, Left Hand /
Sensitivity: Fast, Medium, Slow
Pointer Pointer 1 to 9
Information Usage Time Remaining Lamp Time, Lamp Hour Meter, Projector Usage
Source Page1 Input Terminal, Signal Type, Video Type, Source Name, Entry No.
Source Page2 Horizontal Frequency, Vertical Frequency, Sync Type, Sync Polarity, Interlace
LAN Built-in IP Address, Subnet Mask, Gateway, MAC Address
LAN PC Card IP Address, Subnet Mask, Gateway, MAC Address
LAN Wireless SSID, Mode, WEP, Channel, Signal Level
Version Firmware, Data
Reset Current Signal, All Data, All Data (Including Entry List), Clear Lamp Hour Meter
74
Menu Elements
Tab Slide bar
Highlight
Close button Help button
Radio button
Check box
Solid triangle
OK button Cancel button
Menu windows or dialog boxes typically have the following elements:
Highlight ................ Indicates the selected menu or item.

Solid triangle ......... Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab ........................ Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button ......... Use this round button to select an option in a dialog box.
Check box ............. Place a checkmark in the square box to turn the option On.
Slide bar ................ Indicates settings or the direction of adjustment.
OK button .............. Press to confirm your setting. You will return to the previous menu.
Cancel button ........ Press to cancel your setting. You will return to the previous menu.
Close button .......... Click to close the window and saving changes. (USB mouse only)
Help button ........... Indicates that help about that feature is available (USB mouse only). Press the HELP button on the remote
control to display help.
75
Menu Descriptions & Functions [Source]
Computer 1 and 2
Selects the computer connected to your Computer 1 or Computer 2 input connector signal.
NOTE: An optional component cable (Component V or ADP-CV1 cable) is needed for a component signal.
Video
Selects what is connected to your Video input-VCR, laser disc player, DVD player or document camera.
S-Video
Selects what is connected to your S-Video input-VCR, DVD player, or laser disc player.
NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or S-
Video source.
Viewer
This feature enables you to make presentations using a PC card that contains captured images and slides created
with the exclusive Photo Explore 8.0 for NEC contained on the CD-ROM. See the supplied NEC Software Utility
Installation Guide for installing the Photo Explore 8.0 for NEC.
See page 62 for viewing slides.
LAN
Selects a signal from the LAN port (RJ-45) or the NEC optional wireless LAN card plugged into the projector's card
slot.
76
Entry List
Use the SELECT buttons on your remote control or the projector cabinet to select the signal and press the
ENTER button on the remote control or the projector cabinet to display the Entry Edit Command screen.
Entering the Currently Projected Signal into the Entry List

1. Display the Entry List.
2. Use the SELECT or button on your remote control or the projector cabinet to select any number and
press the ENTER button on the remote control or the projector cabinet to display the Entry Edit Com-
mand screen.
3. Use the SELECT or button to select "Store" and press the ENTER button.
Using the Entry List

Making any adjustments to the current picture will automatically register its adjustments to the Entry List. The regis-
tered signal can be loaded any time from the Entry List.
NOTE: Up to 100 presets can be registered except settings on the Picture.
77
Entry Edit Command
You can edit signals on the Entry List.
Load ...................... Enables you to select a signal from the list.

Store ..................... Enables you to store the currently projected signal.
Cut ........................ Enables you to remove a selected signal from the list and place it on the "clipboard" in the projector.
Copy ...................... Enables you to copy a selected signal from the list and place it on the "clipboard" in the projector.
Paste ..................... Enables you to paste the signal placed on the "clipboard" to any other line of the list.
Edit ........................ Enables you to change source names.
Source Name:
Enter a signal name. Up to 18 alphanumeric characters can be used.
Input Terminal:
Change the input terminal.
Lock:
Set so that the selected signal cannot be deleted when "All Delete" is executed. After executing "Lock", the
changes cannot be saved.
Skip:
Set so that the selected signal will be skipped during auto search.
When complete, select OK and press ENTER. To exit without storing the setting, select Cancel. Select "Source
Name" and press ENTER to display the Source Name Edit window. You can change source name on this
window. Press to display the software keyboard, which you can enter alphanumeric characters. See page
132 for the key function of the software keyboard.
All Delete ............... This feature enables you to delete all the registered signals in the Entry List.
The following buttons are not available for the currently projecting signals:
1) The Cut and Paste buttons on the Entry Edit Command screen
2) The Input Terminal button on the Entry Edit screen
NOTE: When all the signals in the Entry List are deleted, the currently projected signal will be also deleted except locked signals.
78
Menu Descriptions & Functions [Adjust]
Basic
[Brightness]
Adjusts the brightness level or the back raster intensity.
[Contrast]
Adjusts the intensity of the image according to the incoming signal.
[Color]
Increases or decreases the color saturation level (not valid for RGB).
79
[Hue]
Varies the color level from +/- green to +/-blue. The red level is used as reference. This adjustment is only valid for
Video, Component and TV standard inputs (not valid for RGB).
[Sharpness]
Controls the detail of the image for Video (Not valid for RGB).
Using the Wall Color Correction [Wall Color]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following eight options are available.
OFF Blackboard
Light yellow Light green
Light blue Sky blue
Light rose Pink
80
Selecting Aspect Ratio [Aspect Ratio] (not available for Viewer)
Screen Type 4:3 Screen Type 16:9
Aspect Ratio allows you to select the best Aspect mode to display your source image.
When screen type 4:3 is selected for the source, the following selections will display:
4:3 ......................... Standard 4:3 aspect

Letter Box .............. Reduced to display the true aspect with black borders on top and bottom
Wide Screen .......... Left & Right stretched with black borders on top and bottom
Crop ...................... Left & Right stretched. Left & Right sides cut. Available for 4:3 only.
When screen type 16:9 is selected for the source, the following selections will display:
4:3 Window ........... Reduced to display the true aspect with black borders on right and left
Letter Box .............. Standard 16:9 aspect
Wide Screen .......... Left and right stretched to display the true aspect
4:3 Fill ................... Stretched to display in 16:9 aspect ratio
NOTE: You can adjust image position vertically for a source with black borders on top and bottom. See page 98 for setting image
position.
Copyright
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a
coffee shop or hotel and employing compression or expansion of the screen image with a "Aspect Ratio" or "Screen" setting may
raise concern about the infringement of copyrights which are protected by copyright law.
NOTE: During 3D Reform adjustment, "Aspect Ratio" may not be available.

Should this happen, first reset the 3D Reform data and then do setting again. Second repeat the 3D Reform adjustment.
Changing the aspect ratio can limit 3D Reform in its adjustable range.
Input
Signal
Screen
Type 4:3 Letterbox Squeeze
4:3 Screen 4:3 Letterbox Wide Screen Crop
16:9 Screen 4:3 Window 4:3 Fill Letterbox Wide Screen
81
Controlling Volume [Volume]
You can adjust the volume level of the projector speakers and AUDIO OUT (Stereo Mini Jack).
Reset
To reset the settings for Basic, select Reset and press the ENTER button.
The message "The setting values on page will be reset. Are you sure? will be displayed.
Select Yes and press the ENTER button. To return without storing settings, select No and press the ENTER button.
Picture Management
[Preset]
This option allows you to adjust neutral tint for yellow, cyan or magenta. There are 5 factory presets optimized for
various types of images, you can set user adjustable settings.
82
[Detail Settings]
This will provide you with three pages of menus that provide more detailed settings.
[Page1]
Selecting Reference Setting [Reference]

This feature allows you to use color correction or gamma values as reference data to optimize for various types of
images. You can select one of the following five settings.
Presentation ...... Recommended for making a presentation using a PowerPoint file.

Video ................. Recommended for regular picture such as TV program.
Movie ................ Recommended for movies.
Graphic .............. Recommended for graphics.
sRGB ................. Standard color values.
Selecting Gamma Correction Mode [Gamma Correction]
Each mode is recommended for:
Dynamic ............ Creates a high-contrast picture.

Natural ............... Natural reproduction of the picture.
Black Detail ........ Emphasizes detail in dark areas of the picture.
Adjusting Color Temperature [Color Temperature]
This feature adjusts the color temperature using the slide bar. The range is between 5000K and 9300K.
83
NOTE:
* When "Presentation" is selected in "Reference", this function is not available.
* When "White Balance" settings has been changed, the color temperature value on screen does not reflect the real color
temperature.
Adjusting Brightness of White Area [White Peaking]
Adjust the brightness of the white areas by using the slide bar. As the picture becomes dim, it looks more natural.
[Black Expansion]
Automatically minimizes blacks that appear more like shades of gray to provide a true black and white image. The
"On" is the factory preset.
NOTE: This feature is not available for Scart, 480p, 576p, HDTV and RGB signals.
[Page 2]
Adjusting White Balance [White Balance]
This allows you to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the
screen; Contrast for each color (RGB) to adjust the white level of the screen.
[Page 3]
Selecting Color Correction [Color Correction]
Adjusts red, green, blue, yellow, magenta and cyan each independently to correct the tint of the whole screen.
84
Selecting Signal Type [Signal Type]
Select either the computer signal type or the component signal type.
RGB ....................... Computer signal

Component ............ Component signals such as Y/Cb/Cr, Y/Pb/Pr
NOTE: This feature is available on the computer signal only. If you do not get a better picture even when you set "Signal Select" to
"Component" in Setup, set this to "Component".
Selecting Video Filter Level [Video Filter] (not available for Video, Viewer and LAN)
This function reduces video noise.
Off ......................... The filter is removed.

Less ...................... The low-pass filter is applied partially.
More ...................... The low-pass filter is applied fully.
85
Image Options
Adjusting Clock and Phase [Clock/Phase]
This allows you to manually adjust Clock and Phase.
Clock ..................... Use this item to fine tune the computer image or to remove any vertical banding that might appear. This
function adjusts the clock frequencies that eliminate the horizontal banding in the image.
This adjustment may be necessary when you connect your computer for the first time.
Phase .................... Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is
evident when part of your image appears to be shimmering.)
Use "Phase" only after the "Clock" is complete.
Adjusting Horizontal/Vertical Position [Horizontal/Vertical Position]
Adjusts the image location horizontally and vertically.
Masking Unwanted Area [Blanking]
This feature allows you to mask any unwanted area of the screen image.
Adjust the Top, Bottom, Left or Right blanking with the SELECT or button.
86
Selecting Resolution [Resolution]
This allows you to activate or deactivate the Advanced AccuBlend feature.

Auto ...................... Turns on the Advanced AccuBlend feature. The projector automatically reduces or enlarges the current
image to fit the full screen.
Native .................... Turns off the Advanced AccuBlend feature. The projector displays the current image in its true resolution.
See "Auto Adjust" on page 107 for turning on or off the Auto Adjust feature.
NOTE:
* When "Resolution" is set to "Native", "Overscan", "3D Reform", "Aspect Ratio" and "Screen" are not available.
* While you are displaying an image with the projector's native resolution or higher, "Resolution" is not available.
Selecting Overscan Percentage [Overscan]
Select overscan percentage (0%, 5% and 10%) for signal.
87
Video
Selecting Noise Reduction Level [Noise Reduction]

(not available for COMPUTER1/2, Viewer and LAN; available for TV standard inputs)
Select one of the three levels for reducing video noise: Low, Medium or High.
NOTE: The lower the Noise Reduction level, the better the image quality by way of higher video bandwidth.
Selecting Color Matrix [Color Matrix]

(not available for COMPUTER1/2, Viewer and LAN; available for TV standard inputs)
Select an appropriate color matrix for your input signal, either HDTV or SDTV.
Turning On/Off 3 Dimension Separation [3D Y/C Separation]
This function turns on or off the 3 dimensional separation feature.
NOTE: This feature is available for NTSC3.58 of Video signal only.
88
Setting Vertical Edges [Vertical Enhancer]
This function enhances the vertical edges around objects in the image.
NOTE: This function is not available for an RGB and Component signal.
Selecting Interlace or Deinterlace [I/P Converter]
This function allows you to select between "Interlace" and "Deinterlace".
Deinterlace (Auto) ....... The projector automatically determines a still or moving image to display a clear picture. If selecting
"Deinterlace (Auto)" causes excess jitter or artifacts, select "Interlace".
Deinterlace (Still) ......... Select when a still image is displayed. When this option is selected for a moving image, jitter or artifacts
can be seen.
Interlace ...................... Select when a moving image is displayed. This will eliminate jitter and artifacts in a moving image.
89
Menu Descriptions & Functions [Setup]
Basic
Selecting Keystone Mode [Keystone]
This feature allows you to correct keystone distortion manually or automatically.

Selecting this item will display the Keystone setting menu.
Auto ...................... This feature allows the projector to detect its tilt and correct vertical distortion automatically.
Manual .................. You can correct vertical distortion manually from the menu.
Changes will be saved even when you turn off the projector.
Adjust .................... You can display the Keystone screen. See page 33 for more details.
NOTE: When "Cornerstone" is selected, "Adjust" is not available.
90
Selecting Cornerstone Mode [Cornerstone]
This option allows you to correct trapezoidal distortion.

Selecting this item will display the Cornerstone adjustment screen.
See page 43 for more details.
NOTE: When "Keystone" is selected, "Cornerstone" is not available.
Setting Lamp Mode to Normal or Eco [Lamp Mode]
This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be
extended up to 4000 hours by using the Eco mode. Selecting Eco mode decreases fan noise compared to in Normal
mode.
Normal Mode ........ This is the default setting (100% Brightness).

Eco Mode .............. Select this mode to increase the lamp life (80% Brightness).
Selecting Menu Mode [Menu Mode]
This feature allows you to select two menu modes: Basic Menu and Advanced Menu.
Basic Menu ........... This is the basic menu that contains minimum essentials of menus and commands.
Advanced Menu ..... This is the menu that contains all the available menus and commands.
Selecting Menu Language [Language]
You can choose one of 21 languages for on-screen instructions.
91
Menu
Selecting Menu Color [Menu Color Select]
You can choose a color for the menu.
Turning On / Off Source Display and Message [Display Select]
Source ................... This option turns on or off input name display such as Computer 1/2, Video, and No Input to be displayed in
the top right corner of the screen.
Message ................ This option turns on and off messages. Even though selecting Off, the following message will appear.
* The lamp has reached the end of its usable life. Please replace the lamp. Press the EXIT button and the
message will disappear.
* Projector is locked When unlocking the projector security, the message will disappear.
92
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The
preset choices are "Manual", "Auto 5 sec", "Auto 15 sec", and "Auto 45 sec". The "Auto 45 sec" is the factory preset.
Manual .................. The menu can be turned off manually.

Auto 5 sec ............. The menu will automatically be turned off in 5 seconds if no buttons are pressed within 5 seconds.
Auto 15 sec ........... The menu will automatically be turned off in 15 seconds if no buttons are pressed within 15 seconds.
Auto 45 sec ........... The menu will automatically be turned off in 45 seconds if no buttons are pressed within 45 seconds.
Selecting a Color or Logo for Background [Background]
Use this feature to display a blue/black screen or logo when no signal is available. The default background is blue. You
can change the logo screen using the Viewer feature. See pages 70.
Security
Disabling the Cabinet Buttons [Cabinet Button]
This option turns on or off the Cabinet Button Lock function.
NOTE:
This Cabinet Button Lock does not affect the remote control functions.
When the cabinet buttons are locked, pressing and holding the EXIT button for about 10 seconds will change the setting to
unlock.
93
Setting a Password [Password (Menu)] / [Password (Logo)]

A password can be set for your projector to avoid operation by an unauthorized person.
When "Password (Menu)" is set, changing the menu from Basic to Advanced will display "Password (Menu)" input
screen.
When "Password (Logo)" is set, doing any one of the following two operations will display the Password input screen.
Changing the background

Changing the logo data in a PC card
Entry:
To assign your password:
NOTE: Up to 15 alphanumeric characters can be assigned.
1. Type a password.
Highlight "Entry" and press the ENTER button.
The "Enter the Password" screen will be displayed.
Make sure that is highlighted and then press the ENTER button.
The Software keyboard appears. Use the Software keyboard to type a password and then highlight "OK"
on the Enter the Password screen and press the ENTER button.
The [Confirm Password] screen will be displayed.
2. Type the same password again. Highlight "OK" on the Enter the Password screen and press the
ENTER button.
Your password will be assigned.
Delete:
To delete your password:
1. Highlight [Delete] and press the ENTER button. The "Current Password" screen will be displayed.
2. Use the Software keyboard to type your password. Highlight "OK" on the Current Password screen and
then press the ENTER button.
Your password will be deleted.
94
Security
The Security function enables you to protect your projector so that the projector will not project a signal unless you
enter a keyword. There is also an option to lock the projector by using a registered PC card* as a protect key. Once you
have registered your PC card as a protect key, you are required to insert the registered PC card into the PC card slot
of the projector each time you turn on the projector. You can enable the Security function by using a keyword only.
* The projector does not support NTFS formatted flash memory card or USB memory device.
To format your flash memory card or USB memory device in your computer, refer to the document or help file
that comes with your Windows.
Enable/Disable ....... This turns the Security function on or off.

Keyword ................ Enter an appropriate keyword when you use the Security function. (Up to 10 characters can be used.) The
Security function is available only when your keyword is entered.
Use Protect key ..... Check this box to lock your projector when using a PC card. To use a keyword without a PC card, do not
check this box.
Drive ...................... Switches between PC Card slot and USB port (type A).
Read ...................... Reads data from a PC card.
Register ................. Registers data from the PC card. The Security function is not available unless at least one PC card is
registered. (if the Use Protect key check box is selected) Up to 5 PC cards can be registered.
Delete .................... Deletes data of a registered PC card.
To set up a keyword to enable the Security function without using a registered PC card.
1. Use the SELECT button to select Keyword and use the software keyboard to enter a keyword.
NOTE: Please make a note of your keyword.
2. Use the SELECT button to select Enable and use the SELECT button to select OK, then the
Security function will be enabled.
An Are you sure? message will appear. Use the SELECT button to select Yes and press the
ENTER button.
The Security function takes effect.
95
To register a PC card as a protect key.
1. Insert a PC card into the PC card slot of the projector.

2. Use the SELECT button to select "Use Protect Key" and press the ENTER button.
3. Use the SELECT button to select "Read" and press the ENTER button.
Data of the PC card will be read into the projector.
4. Use the SELECT button to select "Register" and press the ENTER button.
Downloaded data will be registered and be displayed in the list window.
5. Use the SELECT button to select "Keyword" and use the software keyboard to enter a keyword.
NOTE: To use a PC card as a protect key, you must also set up a keyword. Please make a note of your keyword.
This completes registration of your PC card.
To enable Security, use the SELECT button to select "Enable" and use the SELECT button to select "OK" and
"Security function will be enabled. An Are you sure?" message will appear. Use the SELECT button and press the
ENTER button.
The Security function takes effect.
To turn on the projector when Security is enabled (when using your keyword only).
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and display a message to the effect that the projector is security-pro-
tected.
The Release Code input screen will be displayed.
3. Enter your keyword in the Release Code input screen.
You can view the projected image.
NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code. See more information at the end of this section.
To turn on the projector when Security is enabled (when using PC card as a protect key).
1. Insert your registered PC card into the PC card slot.

The projector will turn on and then recognize the PC card. Once the image has been projected, it will
stay on without the PC card.
The security disable mode is maintained until the main power is turned off (by setting the main power switch
to "O" or unplugging the power cord). In the following cases you will be asked to check the protect key or input
the keyword:
(1)When "OK" is selected at an image for which security is set and the power is turned off then back on
(2)When the main power is turned off then back on while the security function is enabled
(3)When you attempt to display an image for which security is set while the security function is enabled
Blanks (spaces) cannot be used in the Keyword section.
96
To delete PC card data you registered.
1. Use the SELECT button to select "Delete" and use the SELECT button to select the list window.
2. Use the SELECT button to select the PC card data you wish to delete.
3. Press the SELECT button to select "Delete" and press the ENTER button.
The PC card data will be deleted.
If you've lost your registered PC card, proceed as follows:
NOTE: NEC or your dealer will provide you with your Release Code in exchange for your registered keyword and Request Code.
See more information at the end of this section.
The projector will be turned on and display a message to the effect that the projector is security-pro-
tected.
The Release Code input screen will be displayed as well as your Request Code (24 alphanumeric
characters).
3. Enter your Release Code in the Release Code Input screen.
The projector will turn on.
* If the projector is turned on by entering the Release Code, your Security will be disabled.
NOTE:
Some types of PC cards cannot be registered as your protect key.
It is recommended that you register two or more PC cards in case you lose or damage your registered PC card.
Formatting your registered PC card will disable your protect key function.
NOTE:
Europe : http://www.nec-europe.com/
97
Installation
Selecting Projector Orientation [Orientation]
This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.
NOTE: Selecting one of the other options than Desktop Front will force the Keystone mode to be Manual".
Selecting Aspect Ratio and Position for Screen [Screen]
Screen Type ........... Select one of three options: 4:3 Screen or 16:9 Screen for the screen to be used. See also "Aspect Ratio" on
page 81.
Position ................. This feature allows you to adjust the vertical position of the image when 16:9 has been selected for the
screen type.
When 16:9 has been selected there is black area above and below the image. You can adjust the vertical
position of the image in these areas.
You can adjust the vertical position between top and bottom.
NOTE: This option is available only when "16:9" is selected in Screen Type.
NOTE: During 3D Reform adjustment, "Screen Type" and "Screen Position" may not be available. To make available, first reset the
3D Reform data and then do settings again. Secondly repeat the 3D Reform adjustment. Changing "Screen Type" and "Screen
Position" can limit 3D Reform in its adjustable range.
98
LAN Mode
Setting LAN Mode
This feature allows you to set various setting items when the projector is used on your network.
CAUTION
Consult with your network administrator about these settings.
Connect a LAN cable (Eathernet cable) to the LAN port (RJ-45). See page 22.
For wireless LAN connection, use the NEC optional wireless LAN card (NWL-100*).
* Last digit of the model code varies depending on which country you live in. For more information, visit
the above Website.
To use wireless LAN, insert the NEC optional wireless LAN card (NWL-100*) into the PC Card slot.
See "Inserting and Removing a PC Card on page 24.
Always insert or remove the wireless LAN card when the main power is turned off. Failure to do so may
cause projector malfunction or damage to the wireless LAN card. If the projector will not work correctly,
turn off the projector, wait 90 seconds, and turn it back on.
Hints on How to Set Up LAN Connection

To configure the projector to communicate on the network using the LAN port (RJ-45) or the optional wireless LAN
card:
1. Select the "Built-in" tab for the LAN port (RJ-45) or the "PC Card" tab for the optional wireless LAN
card.
2. On the "Built-in" tab or the "PC Card" tab, select a number from the "Profiles" list for your LAN
settings.
Two settings can be stored in memory for each the LAN port and the wireless LAN card respectively.
3. On the "Built-in" tab or the "PC Card" tab, turn on or off "DHCP", specify IP address, Subnet Mask,
Gateway and DNS Configuration. Select [OK] and press the ENTER button.
See page 100 or 101.
To recall the settings from memory:

After selecting the "Built-in" tab or the "PC Card" tab, select the number from the "Profiles" list.
Select [OK] and press the ENTER button. See page 100 or 101.
To connect a DHCP server:

On the "Built-in" tab or the "PC Card" tab, select "DHCP" and press the ENTER button. A check mark will be
placed. Select again and press the ENTER button. The check box will be cleared.
When setting an IP address without using a DHCP server, clear the check box for "DHCP". See page 100 or 101.
To set only for wireless LAN (Network Type and WEP):

1. On the "PC Card" tab, select "Profiles" and then select "Profile 1" or "Profile 2".
2. On the "PC Card" tab, select "Advanced and press the ENTER button. The "Advanced" menu will be
displayed.
See page 102.
To select a wireless LAN access point:

1. On the "PC Card" tab, select "Profiles" and then select "Profile 1" or "Profile 2".
2. On the "PC Card" tab, select "Advanced and press the ENTER button.
3. On the Advanced menu, select "Network Type" "Site Survey" and press the ENTER button.
4. Select "Mode" and then select "Infrastructure".
See pages 102 and 103.
99
To receive error messages or information on the remaining lamp life via e-mail:
1. On the "Mail" tab, select "Alert Mail" and press the ENTER button. A check mark will be placed.
2. Set "Sender's Address", "SMTP Server Name" and "Recipient's Address". Select [OK] and press the
ENTER button.
See page 105.
To execute "Easy Connection using Image Express Utility 2.0:

The "Easy Connection" is a mode that can abbreviate the troublesome LAN settings when using the Image Ex-
press Utility 2.0 and connecting the PC and projector via a wireless LAN.
The Image Express Utility 2.0 is contained on the supplied User Supportware 2 CD-ROM. To use "Easy Connec-
tion", select "PC Card" "Profiles" "Easy Connection". See page 101.
Built-in
Profiles (for LAN port [RJ-45]):

Up to two settings for the LAN port (RJ-45) can be stored in memory of the projector.
Select "Profile 1" or "Profile 2" and then do settings for "DHCP" and the other options.
After doing this, select [OK] and press the ENTER button. This will store your settings in memory.
DHCP:
Enabling this option automatically assigns an IP address to the projector from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from your network
administrator.
IP Address ............. Set your IP address. Press to display the software keyboard and type in 12 numeric characters.
Subnet Mask ......... Set your subnet mask number. Press to display the software keyboard and type in 12 numeric characters.
Gateway ................ Set the default gateway of the network connected to the projector. Press to display the software keyboard
and type in 12 numeric characters.
DNS Configuration Type in the IP address of DNS server on the network connected to the projector. Twelve numeric characters
are used.
Reconnect ............. Use this button to connect the projector to a network.
100
PC Card
Profiles (for PC Card):

To execute a wireless LAN easily using Image Express Utility 2.0, select Easy Connection.
Up to two settings for the optional wireless LAN card can be stored in memory of the projector.
Select "Profile 1" or "Profile 2" and then do settings for "DHCP" and the other options.
After doing this, select [OK] and press the ENTER button. This will store your settings in memory.
DHCP:
Place a check mark to automatically assign an IP address to the projector from your DHCP server.
Clear this check box to register the IP address or subnet mask number obtained from your network administrator.
IP Address ............. Set your IP address. Press to display the software keyboard and type in 12 numeric characters.
Subnet Mask ......... Set your subnet mask number. Press to display the software keyboard and type in 12 numeric characters.
Gateway ................ Set the default gateway of the network connected to the projector. Press to display the software keyboard
and type in 12 numeric characters.
DNS Configuration Type in the IP address of DNS server on the network connected to the projector. Twelve numeric characters
are used.
Advanced .............. Displays the Advanced menu which includes various setting for wireless LAN connection (Network Type
and WEP). See the Advanced menu later on.
Reconnect ............. Use this button to connect the projector to a network.
101
Advanced menu
Network Type (required for wireless only)
Site Survey:
Displays a list of available SSIDs for wireless LAN on site. Select an SSID which you can access.
To select an SSID, highlight the SSID and use the SELECT to select [OK] and press the ENTER button.
: access point
: Ad Hoc PC
: WEP enabled
NOTE: You cannot connect to a device with the SSID for Channel 14 because it is not displayed in the list.
SSID (Network name):

Enter an identifier (SSID) for wireless LAN when selecting [Infrastructure] or [802.11 Ad Hoc] in [Mode]. Commu-
nication can be done only with equipment whose SSID matches SSID for your wireless LAN. Up to 32 alphanu-
meric characters can be used.
NOTE: To disable SSID, select a space (null) or "ANY"(All caps).
Mode:
Select communication method when using wireless LAN.
Infrastructure ........ Select this option when communicating with one or more equipment connected to the wireless or wired
LAN network via an access point.
802.11 Ad Hoc ...... Select this option when using the wireless LAN to directly communicate with a computer in peer-to-peer
mode. This is a method that meets the IEEE802.11 wireless standard.
NOTE: When in Ad Hoc mode, only 802.11b is available for communication method.
Data transmission speed in Ad Hoc mode is limited up to 11Mbps.
102
WEP (required for wireless only)
Select this option whether using the WEP (Wired Equivalent Privacy) key for encryption or not. To use encryption,
specify WEP key.
Disable .................. Will not turn on the encryption feature. Your communications may be monitored by someone.
64bit ...................... Uses 64-bit datalength for secure transmission.
128bit .................... Uses 128-bit datalength for secure transmission. This option will increase privacy and security when com-
pared to use of 64-bit datalength encryption.
152bit .................... Uses 152-bit datalength for secure transmission. This option will increase privacy and security when com-
pared to use of 128-bit datalength encryption.
NOTE:
The WEP settings must be the same as communication devices such as PC or access point in your wireless network.
When you use WEP, your image transmission speed will slow down.
Key Select:
Selects one key from the four keys below when selecting [64bit], [128bit] or [152bit] in [WEP].
Key1-4:
Enter encryption key when selecting [64bit], [128bit] or [152bit] in [WEP].
Up to 5 characters can be set in 64 bit, up to 13 characters in 128 bit and up to 16 characters in 152 bit. Press the
HEX button to change to ASCII to set the key in ASCII digit. You can toggle this button between ASCII and
HEX.
The key can also be set in hexadecimal digit.
* Enter 0X(numeral and alphabet respectively) right in front of your key code.
* Hexadecimal uses 0 to 9 and A to F.
* When setting in a hexadecimal digit, up to 10 characters can be set in 64 bit, up to 26 characters in 128 bit
and up to 32 characters in 152 bit.
103
Using Software Keyboard to enter an encryption key
1. Select one of Key 1, Key 2, Key 3 and Key 4 and press the ENTER button.
The software keyboard will be displayed.
2. Use the SELECT button to select one key and press the ENTER button.
3. After finishing entering the WEP key, use the SELECT button to select [OK] and press the
ENTER button.
The software keyboard will disappear.
Domain
Host Name ............ Type in a hostname. Up to 60 alphanumeric characters can be used.

Domain Name ....... Type in domain name of the network connected to the projector. Up to 60 alphanumeric characters can be
used.
104
Mail
Alert Mail:
Checking this box enables Alert Mail feature.
This option notifies your computer of an error message via e-mail when using wireless or wired LAN. The error
message will be notified when the projector lamp has reached the end of its usable life or an error occurs in the
projector.
Sample of a message sent from the projector:

The lamp is at the end of its usable life. Please replace the lamp.
Projector Name: X X X X
Lamp Hour Meter: xxxx [H]
Projector Usage: xxxxxx [H]
Sender's Address:
Specify the senders address. Use the Software keyboard. Up to 60 alphanumeric and symbols characters can be
used. See "Using Software Keyboard" in Appendix for more details.
SMTP Server Name:

Type in the SMTP server name to be connected to the projector. Up to 60 alphanumeric characters can be used.
Recipient's Address 1 to 3:
Type in your recipient's address. Up to 60 alphanumeric and symbols characters can be used.
Test Mail:
Send a test mail to check if your settings are correct.
NOTE:
If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if the Recipient's
Address is correctly set.
Unless any one of the "Sender's Address", "SMTP Server's Name" or "Recipient's Address 1-3" is selected, "Test Mail" is not
available.
Be sure to highlight OK and press the ENTER button before executing Test Mail.
NOTE: To use the Mail Alert feature on wireless LAN connection, select "Infrastructure" for "Mode" in "Network Type."
105
Projector Name
Specify a unique projector name. Press to display the software keyboard and type in. Up to 16 alphanumeric
characters can be used. After entering a name, select [OK] and press the ENTER button.
Using Software Keyboard
1 to 0 and
Characters ....... Use to type in password or keyword.
MODE .................... Selects one of three modes for alphabet and special characters.
SP ......................... Inserts a space
BS ......................... Deletes one character backward
Returns to the previous
Advances to the next
OK ......................... Executes the selection
Cancel ................... Cancels the selection
Selecting Communication Speed [Communication Speed]
This feature sets the baud rate of the PC Control port (Mini DIN 8 Pin). It supports data rates from 4800 to 38400 bps.
The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the
equipment, a lower baud rate may be recommended for long cable runs).
106
Options
Setting Auto Adjust [Auto Adjust]
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise
and stability. You can automatically make adjustment in two ways: Normal and Fine.
Off ......................... The RGB image will not be automatically adjusted.

You can manually optimize the RGB image.
Normal .................. Default setting. The RGB image will be automatically adjusted. Normally select this option.
Fine ....................... Select this option if fine adjustment is needed. It takes more time to switch to the source than when "Normal"
is selected.
Enabling Auto Start [Auto Start]
Turns the projector on automatically when the power cable is inserted into an active power outlet and the main power
switch is turned on. This eliminates the need to always use the "Power" button on the remote control or projector
cabinet.
Enabling Power Management [Power Management]
When this option is on and there is no input for five minutes or more, the projector will automatically turn itself off.
107
Enabling High Speed Fan Mode [Fan Mode]
This option allows you to select two modes for fan speed: Auto mode and High speed mode.
Auto ...................... The built-in fans automatically run at a variable speed according to the internal temperature.
High ...................... The built-in fans run at high speed.
When you wish to cool down the temperature inside the projector quickly, select High.
NOTE: Select High mode if you continue to use the projector for consecutive days.
Selecting Default Source [Default Source Select]:
You can set the projector to default to any one of its inputs each time
the projector is turned on.
Last ....................... Sets the projector to default to the previous or last active input each time the projector is turned on.
Auto ...................... Searches for an active source in order of Computer1 Computer2 Video S-Video Viewer LAN
Computer1 and displays the first found source.
Select .................... Displays the selected source input every time the projector is started up. Select an input from the pull-down
menu.
108
Selecting Signal Format [Signal Select]
Computer 1/2
Allows you to set "Computer 1" and "Computer 2" to automatically detect an incoming RGB or component source
such as a computer or DVD player. However there may be some RGB and component signals that the projector is
unable to detect. In this case, select "RGB" or "Component".
Select "Scart" in COMPUTER 1 for the European Scart signal.
Video and S-Video

This feature enables you to select video standards manually.
Normally select "Auto". Select the video standard from the pulldown menu. This must be done for Video and S-
Video separately.
Setting MONITOR OUT Connector [OUT Terminal]
This option allows you to determine which RGB or component source is output from the MONITOR OUT connector
during Standby mode.
Last ....................... The signal from the last COMPUTER1 or 2 input will be output to the MONITOR OUT connector.
COMPUTER 1, 2 .... The signal from the COMPUTER1 or 2 input will be output to the MONITOR OUT connector.
109
Tools
Selecting the ChalkBoard [ChalkBoard]

This option displays the ChalkBoard tool bar.
The ChalkBoard feature allows you to write and draw messages on a projected image.
NOTE: The ChalkBoard feature is available only when a USB mouse is used.
To display or hide the ChalkBoard tool bar, click the middle button on your mouse.
The tool bar contains the following icons.
Drag ................. Drags to move the tool bar.

Pen ................... Left-click and drag to draw. Left-click or right-click the pen icon to display the pen palette containing four
lines of different thickness from which you can select a line you prefer by left-clicking.
Color ................ Selects a color. Left-click to display the color palette from which you can select a color you prefer by left-
clicking.
Capture ............. Left-click to capture a drawing on the ChalkBoard screen and save it to your PC-card inserted into the PC
card slot of the projector.
Eraser ............... Left-click and drag to erase part of a drawing. Left-click or right-click the eraser icon to display the eraser
palette containing four eraser of different thickness from which you can select an eraser you prefer by left-
clicking.
Clear ................. Left-click to clear the drawing completely from the ChalkBoard screen.
Hide .................. Hides the tool bar by left-clicking. Right-clicking anywhere on the screen displays the ChalkBoard tool bar
again.
Exit ................... Clears the complete drawing and exits the ChalkBoard.
NOTE:
The menu is not available while you display the ChalkBoard screen.
Selecting another source or switching slides in the Viewer clears a drawing completely.
110
Using Off Timer [Off Timer]
1. Select your desired time between 30 minutes and 16 hours: Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Select OK and press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
To cancel the preset time, set "Off" for the preset time or turn off the power.
When the remaining time reaches 3 minutes before the projector is turned off, the "Projector will turn off in 3 minutes"
message will be displayed on the bottom of the screen.
Setting Mouse Pointer, Button and Sensitivity [Mouse]
This option lets you to change your USB mouse settings. The mouse settings feature is available for USB mouse only.
Choose the settings you want:
Mouse Pointer ....... Pointer 1 - 9

Mouse Button ........ "Right Hand" or "Left Hand"
Mouse Sensitivity .. "Fast", "Medium" or "Slow"
Selecting Projecting Pointer Icon [Pointer]
This enables you to select from nine different Pointer icons for the "POINTER" button on your remote control.
After moving your Pointer icon to the area you want on the screen, press the MAGNIFY button on the remote control
to enlarge the selected area on the screen. See page 40 for more details.
NOTE: There may be cases where the Pointer function is not available (ex. A non-interlace signal at 15kHz such as video game.)
111
Menu Descriptions & Functions [Information]
Displays the lamp and the projector usage hours, the status of the current signal and settings and LAN settings. This
dialog box has seven pages.
The information included are as follows:
Usage Time
Remaining Lamp Time (%)

Lamp Hour Meter (H)
Projector Usage (H)
NOTE: The progress indicator shows the percentage of remaining lamp life. The value informs you of the amount of lamp and
projector usage respectively.
112
Source Page1
Input Terminal Signal Type

Video Type Source Name
Entry No.
Source Page2
Horizontal Frequency Vertical Frequency

Sync Type Sync Polarity
Interlace
113
LAN Built-in
This page shows information on settings for the LAN port (RJ-45)
IP Address ............. Indicates the IP address of the projector when the LAN port (RJ-45) is used.
Subnet Mask ......... Indicates the subnet mask of the projector when the LAN port (RJ-45) is used
Gateway ................ Indicates the gateway of the network connected to the projector when the LAN port (RJ-45) is used.
MAC Address ........ Indicates the MAC address of the LAN port (RJ-45).
LAN PC Card
This page shows information on settings for the optional wireless LAN card
IP Address ............. Indicates the IP address of the projector when the optional wireless LAN card is used.
Subnet Mask ......... Indicates the subnet mask of the projector when the optional wireless LAN card is used.
Gateway ................ Indicates the gateway of the network connected to the projector when the optional wireless LAN card is
used.
MAC Address ........ Indicates the MAC address of the optional wireless LAN card.
114
LAN Wireless
This page shows information on settings for WEP key for encryption.
SSID ...................... Indicates the identifier (SSID) for your wireless LAN.
Mode ..................... Indicates that "Infrastructure" or "802.11 Ad Hoc" is selected for your communication method
WEP ...................... Indicates your selected datalength encryption: On or Off
Channel ................. Indicates the channel you selected in the Site Survey. The channel must match for all wireless devices
communicating on your wireless LAN.
Signal Level ........... Indicates receiving condition of radio signal level while you are using a wireless LAN connection (Only when
PC Card is used)
Version
Firmware
Data
115
Menu Descriptions & Functions [Reset]
Returning to Factory Default
The Reset feature allows you to change adjustments and settings to the factory preset for sources by the following
methods:
[Current Signal]
Resets the adjustments for the current signal to the factory preset levels.
All the items in Adjust (except Wall Color) can be reset.
[All Data]
Reset all the adjustments and settings for all the signals to the factory preset except Entry List, Language, Back-
ground, Cabinet Button Lock, Password (Menu), Password (Logo), Security, LAN Mode, Projector Name,
Commnication, Remaining Lamp Time, Lamp Hour Meter and Projector Usage.
[All Data (Including Entry List)]

Reset all the adjustments and settings for all the signals to the factory preset except Language, Background,
Cabinet Button Lock, Password (Menu), Password (Logo), Security, LAN Mode, Projector Name, Commnication,
Remaining Lamp Time, Lamp Hour Meter and Projector Usage.
Also deletes all the signals in the Entry List and returns to the factory preset.
NOTE: Locked signals in Entry List cannot be reset.
Clearing Lamp Hour Meter [Clear Lamp Hour Meter]

Resets the lamp clock back to zero.
NOTE: The projector will turn off and go into standby mode after 2100 hours (up to 4100 hours in Eco mode) of service. In this
condition you cannot clear the lamp hour meter on the menu. If this happens, press the "HELP" button on the remote control for
ten seconds to reset the lamp clock back to zero. Do this only after replacing the lamp.
116
7
Maintenance
Cleaning the Cabinet .............................................. 118
Cleaning the Lens ................................................... 118
Replacing the Lamp ................................................ 119
117
7. Maintenance
This section describes the simple maintenance procedures you should follow to replace the lamp, and to clean the
cabinet and the lens.
Cleaning the Cabinet
1. Turn off the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong
detergents or solvents such as alcohol or thinner.
Cleaning the Lens

Use a blower or lens paper to clean the lens, and be careful not to scratch the lens.
Lens Protector
The lens barrel has threads on the outside for mounting a commercially available step-up ring (77mm 82mm) and
lens protector (82mm) to protect the lens from dirt, dust, scratches and damage. Note that both a lens protector and
the supplied lens cap cannot be used at the same time.
CAUTION: Use only transparent lens protectors designed for lens protection.
Use of filters for light reduction and special effects, such as ND (Neutral Density) filters and color filters, can
absorb heat, resulting in damage to the filter and the projector.
118
7. Maintenance
Replacing the Lamp

After your lamp has been operating for 2000 hours (up to 4000 hours : Eco mode) or longer, the "Lamp" indicator in the
cabinet will blink red and the message will appear. Even though the lamp may still be working, replace it at 2000 hours
(up to 4000 hours : Eco mode) to maintain optimal projector performance.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
wait 90 seconds, turn off the main power switch, and then disconnect the power cable. Allow at least one hour
for the lamp to cool before handling.
DO NOT REMOVE ANY SCREWS except the lamp cover screw and two lamp case screws. You could receive
an electric shock.
Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints in the glass surface might
cause an unwanted shadow and poor picture quality.
The projector will turn off and go into stand by mode after 2100 hours (up to 4100 hours : Eco mode) of service.
If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000 hours (up to 4000 hours :
Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp housing. Do not
touch them as the pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
To replace the lamp:

1. Loosen the lamp cover screw until the screwdriver goes into a freewheeling condition and remove the
lamp cover. The lamp cover screw is not removable.
2. Loosen the two screws securing the lamp housing until the screwdriver goes into a freewheeling
condition. The two screws are not removable.
119
7. Maintenance
3. Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
Interlock
4. Insert a new lamp housing until the lamp housing is plugged into the socket.
CAUTION
Do not use a lamp other than the NEC replacement lamp (LT60LPK).
5. Secure it in place with the two screws.

Be sure to tighten the screws.
120
7. Maintenance
6. Reattach the lamp cover.
7. Tighten the lamp cover screw.

Be sure to tighten the screw.
8. After you install a new lamp, select the menu [Reset] [Clear Lamp Hour Meter] to clear the Remaining
Lamp Time and the Lamp Hour Meter.
NOTE: When the lamp exceeds 2100 hours (up to 4100 hours in Eco mode) of service, the projector cannot turn on and the
menu is not displayed. If this happens, press the HELP button on the remote control for a minimum of 10 seconds while in
standby mode. When the lamp time clock is reset to zero, the LAMP indicator goes out.
121
8
Appendix
Troubleshooting ...................................................... 123
Specifications ......................................................... 126
Cabinet Dimensions ............................................... 128
Pin Assignments of D-Sub COMPUTER 1/2 Input

Connector ............................................................ 129
Compatible Input Signal List ................................... 130
PC Control Codes and Cable Connection .............. 131
Using Software Keyboard ....................................... 132
Troubleshooting Check List ..................................... 133
TravelCare Guide .................................................... 135
122
8. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition Projector Condition Note
Off The main power is off
Blinking light Green 0.5 sec On, The projector is getting ready to turn on. Wait for a moment.
0.5 sec Off
2.5 sec On, Off Timer is activated.
0.5 sec Off
Orange 0.5 sec On, The projector is cooling down. Wait for a moment.
0.5 sec Off
Steady light Green The projector is turned on.
Orange The projector is in Standby.
Status Indicator
Off Normal
Blinking light Red 1 cycle (0.5 sec On, Lamp cover error Replace the lamp cover correctly.
2.5 sec Off) (Page 121)
2 cycle (0.5 sec On, Temperature error The projector is overheated. Move
0.5 sec Of) the projector to a cooler location.
3 cycle (0.5 sec On, Power error Power unit will not work correctly.
0.5 sec Off)
4 cycle (0.5 sec On, Fan error Fans will not work correctly.
0.5 sec Off)
6 cycle (0.5 sec On, Lamp error Lamp fails to light. Wait a full
0.5 sec Off) minute and then turn on again.
Green Re-firing the lamp The projector is re-firing.
Orange 1 cycle(0.5 sec On, Network conflict Both the built-in LAN and the wireless
2.5 sec Off) LAN cannot be connected to the same
network at the same time.
To use both built-in LAN and wireless
LAN at the same time, connect them to
different networks. (page 100)
Steady light Orange Cabinet button is locked You have pressed cabinet button
when Cabinet Button is locked.
(Page 93)
Lamp Indicator
Off Normal
Blinking light Red Lamp has reached its end of life. Lamp Replace the lamp.
replacement message will be displayed. (Page 119)
Steady light Red Lamp has been used beyond its limit. The Replace the lamp.
projector will not turn on until the lamp is (Page 119)
replaced.
Green Lamp mode is set to Eco mode
123
8. Appendix
Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 123.)
Problem Check These Items
Does not turn on Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. See pages 26 and 28.
Ensure that the lamp cover is installed correctly. See page 121.
Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (up to 4100 hours : Eco
mode). If there is insufficient ventilation around the projector or if the room where youre presenting is par-
ticularly warm, move the projector to a cooler location.
The lamp may fail to light. Wait a full minute and then turn on the power again.
The lamp has reached the end of its usable life. Replace the lamp.
Will turn off Ensure that the Power Management is off. See page 107.
No picture Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1/2, the VIEWER
or the LAN button on the remote control to select your source. See page 30.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. See page 79.
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the Reset in the Menu. See page 116.
Enter your registered keyword if the Security function is enabled. See page 48.
When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER
button again to resume.
See also the next page.
Color tone or hue is Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 80.
unusual Adjust "Hue" in "Adjust". See page 80.
Image isnt square to Reposition the projector to improve its angle to the screen. See page 31.
the screen Use the 3DReform function to correct the trapezoid distortion. See page 33.
Picture is blurred Adjust the focus. See page 32.

Reposition the projector to improve its angle to the screen. See page 31.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
15.
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Image is scrolling Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1/2, the VIEWER
vertically, horizontally or the LAN button on the remote control to select your source (Video, S-Video, Computer, Viewer or LAN). See
or both page 30.
Adjust the computer image manually with the Clock/Phase in Adjust Image Options. See page 86.
Remote control does Install new batteries. See page 12.

not work Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. See page 12.
Indicator is lit or See the POWER/STATUS/LAMP Indicator on page 123.

blinking
Vertical stripes in RGB Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. See
mode page 35.
Adjust the computer image manually with the Clock/Phase in Adjust Image Options. See page 86.
USB mouse does not Make sure that your USB mouse is properly connected to the projector.
work The projector may not support some brands of a USB mouse.
Capture function is not The Capture function is not available on LAN. See page 30.
possible.
For more information contact your dealer.
124
8. Appendix
If there is no picture, or the picture is not displayed correctly.
Power on process for the projector and the PC.

Be sure to connect the RGB cable between the projector and the computer before turning on the computer.
There are some notebook PCs, which do not output signal unless there is a projector or monitor connected first.
NOTE: You can check the horizontal frequency of the current signal in the projectors menu under Information. If it reads
0kHz, this means there is no signal being output from the computer. See page 113 or go to next step.
Enabling the computers external display.

Displaying an image on the notebook PCs screen does not necessarily mean it outputs a signal to the projec-
tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the Fn key along with one of the 12 function keys gets the external display to come
on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle
through external display selections.
Non-standard signal output from the computer

If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PCs LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the
previous step. Refer to your computers documentation for detailed information.
Image displayed is incorrect when using a Macintosh

When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-
tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP
switch to the 13 fixed mode and then restart your Macintosh. After that, restore the DIP switches to a
displayable mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
Mirroring on a PowerBook
* When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless mirror-
ing is off on your PowerBook. Refer to owners manual supplied with your Macintosh computer for mirroring.
Folders or icons are hidden on the Macintosh screen

Folders or icons may not be seen on the screen. Should this happen, select [View] ->[Arrange] from the Apple
menu and arrange icons.
125
8. Appendix
Specifications
This section provides technical information about the LT265/LT245 Projector's performance.
Model Number LT265/LT245
Optical
DMD Single Chip Digital Micromirror Device (DMD)
Resolution 1024 768 pixels* up to UXGA with Advanced AccuBlend
Lens Manual zoom and focus:
LT265: F2.1 - 2.3 f=28.2mm - 33.6mm
LT245: F2.2 - 2.5 f=22.1mm - 26.5mm
Lamp 220 W DC standard
Image Size 30 inches - 500 inches (0.8 m - 12.7 m) diagonal
Projection Distance LT265: 3.8ft - 80.7ft / 1.20m - 24.5m
LT245: 2.95ft - 62.3ft / 0.90m - 19.1m
Projection Angle LT265: 14.8-15.4(wide) / 12.3-12.7(tele)
LT245: 18.5-19.4(wide) / 15.6-16.2(tele)
Electrical
Inputs 2 RGB (Mini D-Sub 15p), 1 S-Video (Mini DIN 4p), 1 Video, 1 PC Card,
1 Stereo Mini Audio, 1 (L/R) RCA Audio, 1 PC Control (Mini DIN 8p)
Outputs 1 RGB (Mini D-Sub 15p), 1 Stereo Mini Audio
USB Port 1 A Type
LAN Port RJ-45
Video Compatibility NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM, 1080i, 720p,
576p, 576i, 480p, 480i (w/optional cable)
Scan Rate Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 48 Hz to 120 Hz
Video Bandwidth RGB: 100 MHz (-3dB)
Pixel Clock Freq Less than 135 MHz
Color Reproduction 16.7 million colors simultaneously, Full color
Horizontal Resolution NTSC / NTSC4.43/PAL / YCbCr: 540 TV lines
SECAM: 300 TV lines
RGB: 1024 dots (H) 768 dots (V)
External Control RS232, IR, LAN, USB
Sync Compatibility Separate Sync / Composite Sync / Sync on G
Built-in Speakers 2W 1 (monaural)
Power Requirement 100 - 240V AC, 50/60Hz
Input Current 3.1 - 1.4A
Power Consumption 290W in Lamp Normal mode
240W in Lamp Eco mode
12W in Standby mode
* Effective pixels are more than 99.99%.
126
8. Appendix
Mechanical
Installation Orientation: Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Dimensions 10.2" (W) 3.6" (H) 10.8" (D)
260mm (W) 92mm (H) 275mm (D)
(not including protrusions)
Net Weight LT265: 6.5 lbs / 2.9 kg
LT245: 7.1 lbs / 3.2 kg
Environmental Considerations
Operational Temperatures :
41 to 95F (5 to 35C), 20% to 80% humidity
(non-condensing)
Storage Temperatures :
14 to 122F (-10 to 50C), 20% to 80% humidity
(non-condensing)
Regulations UL Approved (UL 60950, CSA 60950)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS CISPR.22 Class B
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-
3)
Meets Low Voltage Directive (EN60950, TV GS Approved)

Europe : http://www.neceurope.com/
Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
The specifications are subject to change without notice.
127
128
Unit: mm (inch)
83 (3.27")
107 (4.2")
123 (4.84")
Lens center
57 (2.24") Lens center
260 (10.24")
275 (10.83")
LT265: 313 (12.32") / LT245: 315 (12.4")
SOURCE AUTO ADJUST

SELECT
LAMP
STATUS
3D REFORM ON/STAND BY POWER
PC CARD
92 (3.6")
AUDIO OUT
PC CARD LAN USB
Cabinet Dimensions
8. Appendix
8. Appendix
Pin Assignments of D-Sub COMPUTER 1/2 Input Connector

Mini D-Sub 15 Pin Connector
Signal Level
5 4 3 2 1
10 9 8 7 6
Video signal : 0.7Vp-p (Analog)
15 14 13 12 11 Sync signal : TTL level
* COMPUTER 1 IN connector only
Pin No. RGB Signal (Analog) YCbCr Signal

1 Red Cr
2 Green or Sync on Green Y
3 Blue Cb
4 Ground
5 Ground
6 Red Ground Cr Ground
7 Green Ground Y Ground
8 Blue Ground Cb Ground
9 No Connection
10 Sync Signal Ground
11 Ground
12 Bi-directional DATA (SDA)*
13 Horizontal Sync or Composite Sync
14 Vertical Sync
15 Data Clock*
129
8. Appendix
Compatible Input Signal List

Signal Resolution Frequency H. Refresh Rate Dot Clock
( Dots ) ( kHz ) ( Hz ) ( MHz )
NTSC 15.734 60
PAL 15.625 50
SECAM 15.625 50
VESA 640 480 31.47 59.94 25.175
IBM 640 480 31.47 60 25.175
MAC 640 480 31.47 60 25.175
MAC 640 480 34.97 66.67 31.334
MAC 640 480 35 66.67 30.24
VESA 640 480 37.86 72.81 31.5
VESA 640 480 37.5 75 31.5
IBM 640 480 39.375 75 31.49
VESA 640 480 43.269 85.01 36
IBM 720 350 31.469 70.09 28.322
VESA 720 400 37.927 85.04 35.5
IBM 720 350 39.44 87.85 35.5
IBM 720 400 39.44 87.85 35.5
VESA 800 600 35.16 56.25 36
VESA 800 600 37.879 60.32 40
VESA 800 600 48.077 72.19 50
VESA 800 600 46.88 75 49.5
VESA 800 600 53.674 85.06 56.25
MAC 832 624 49.725 74.55 57.283
VESA 1024 768 35.5 43 Interlaced 44.9
VESA 1024 768 48.363 60 65
VESA 1024 768 56.476 70.07 75
MAC 1024 768 60.241 74.93 80
VESA 1024 768 60.023 75.03 78.75
VESA 1024 768 68.677 85 94.5
# VESA 1152 864 67.5 75 108
# MAC 1152 870 68.681 75.06 100
# SUN 1152 900 61.796 65.95 92.94
# SGI 1152 900 71.736 76.05 105.6
# VESA 1280 960 60 60 108
# VESA 1280 1024 63.981 60.02 108
# MAC 1280 1024 69.89 65.2 118.5
# HP 1280 1024 78.125 72.01 135
# SUN 1280 1024 81.13 76.11 135
# VESA 1280 1024 79.976 75.03 135
# VESA 1280 1024 91.146 85.02 157.5
# HDTV (1080i)(1125i) 1920 1080 33.75 60 Interlace 74.25
# HDTV (1080i)(1125i) 1920 1080 28.13 50 Interlace 74.25
# HDTV (720p)(750p) 1280 720 45 60 Progressive 74.25
SDTV (480p)(525p) 31.47 59.94 Progressive 27
# VESA 1600 1200 75.0 60 162
# VESA 1600 1200 81.3 65 175.5
# VESA 1600 1200 87.5 70 189
# VESA 1600 1200 93.75 75 202.5
DVD YCbCr 15.734 59.94 Interlaced
DVD YCbCr 15.625 50 Interlaced
#:Images in above flagged with # are compressed with Advanced AccuBlend on LT265 and LT245.
NOTE: Some composite sync signals may not be displayed correctly.

Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
UXGA (1600 1200) is supported for separate sync signal only.
130
8. Appendix
PC Control Codes and Cable Connection

PC Control Codes
Function Code Data

POWER ON 02H 00H 00H 00H 00H 02H
POWER OFF 02H 01H 00H 00H 00H 03H
INPUT SELECT COMPUTER 1 02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT COMPUTER 2 02H 03H 00H 00H 02H 01H 02H 0AH
INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH
INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H
INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H
PICTURE MUTE ON 02H 10H 00H 00H 00H 12H
PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H
SOUND MUTE ON 02H 12H 00H 00H 00H 14H
SOUND MUTE OFF 02H 13H 00H 00H 00H 15H
ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H
ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H
ASPECT RATIO (4:3 Screen)
4:3 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H
Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H
Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H
Crop 03H 10H 00H 00H 05H 18H 00H 00H 03H 00H 33H
ASPECT RATIO (16:9 Screen)
4:3 Window 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H
Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H
Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H
4:3 Fill 03H 10H 00H 00H 05H 18H 00H 00H 04H 00H 34H
AUTO ADJUST 02H 0FH 00H 00H 02H 05H 00H 18H
NOTE: Contact your local dealer for a full list of PC Control Codes if needed.
Cable Connection
Communication Protocol
Baud rate ........................................ 38400 bps
Data length ..................................... 8 bits
Parity .............................................. No parity
Stop bit .......................................... One bit
X on/off .......................................... None
Communications procedure ........... Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
131
8. Appendix
PC Control Connector (DIN-8P)
To RxD of PC
8 6
7
5 4 3
2 1
To GND of PC To TxD of PC
NOTE1: Pins 2, 3, 5, 6 and 8 are used inside the projector.
NOTE 2: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.
Using Software Keyboard
1 to 0 and Characters
.............................. Use to type in password or keyword.
MODE .................... Selects one of three modes for alphabet and special characters.
SP ......................... Inserts a space
BS ......................... Deletes one character backward
.......................... Returns to the previous
.......................... Advances to the next
OK ......................... Executes the selection
Cancel ................... Cancels the selection
NOTE: You can drag the Software keyboard on the screen by clicking and holding any part on the keyboard except buttons.
132
8. Appendix
Troubleshooting Check List

Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by
referring to the Troubleshooting section in your users manual. This checklist below will help us solve your problem
more efficiently.
* Print the following pages.
Frequency of occurrence always sometimes (How often?_____________________) other (__________________)

Power
No power (POWER indicator does not light green) See also Sta- Shut down during operation.
tus Indicator (STATUS). Power cable's plug is fully inserted into the wall outlet.
Power cable's plug is fully inserted into the wall outlet. Lamp cover is installed correctly .
Main power switch is pressed to the ON position. Power Management is turned off (only models with the Power
Lamp cover is installed correctly . Management function).
Lamp Hour Meter (lamp operation hours) was cleared after Sleep Timer is turned off (only models with the Sleep Timer
lamp replacement. function ).
No power even though you press and hold the POWER button
for a minimum of 2 seconds.
Video and Audio
No image is displayed from your PC or video equipment to the Parts of the image are lost.
projector. Still unchanged even though you press the AUTO ADJUST but-
Still no image even though you connect the projector to the PC ton.
first, then start the PC. Still unchanged even though you carry out Reset in the
Enabling your notebook PCs signal output to the projector. projectors menu.
A combination of function keys will enable/disable the ex- Image is shifted in the vertical or horizontal direction.
ternal display. Usually, the combination of the Fn key along Horizontal and vertical positions are correctly adjusted on a
with one of the 12 function keys turns the external display computer signal.
on or off.
Input source's resolution and frequency are supported by the
No image (blue background, logo, no display). projector.
Still no image even though you press the AUTO ADJUST but- Some pixels are lost.
ton.
Image is flickering.
Still no image even though you carry out Reset in the
projectors menu. Still unchanged even though you press the AUTO ADJUST but-
ton.
Signal cable's plug is fully inserted into the input connector
Still unchanged even though you carry out Reset in the
A message appears on the screen. projectors menu.
( _____________________________________________ )
Image shows flickering or color drift on a computer signal.
The source connected to the projector is active and available.
Image appears blurry or out of focus.
Still no image even though you adjust the brightness and/or
the contrast. Still unchanged even though you checked the signals resolu-
tion on PC and changed it to projectors native resolution.
Input source's resolution and frequency are supported by the
projector. Still unchanged even though you adjusted the focus.
Image is too dark. No sound.
Remains unchanged even though you adjust the brightness Audio cable is correctly connected to the audio input of the
and/or the contrast. projector.
Image is distorted. Still unchanged even though you adjusted the volume level.
Image appears to be trapezoidal (unchanged even though you AUDIO OUT is connected to your audio equipment (only mod-
carry out the Keystone" or 3D Reform adjustment). els with the AUDIO OUT connector).
Other
Remote control does not work. Buttons on the projector cabinet do not work ( only models with
No obstacles between the sensor of the projector and the re- the Key Lock function).
mote control. Cabinet Button Lock is not turned on or is disabled in the menu.
Projector is placed near a fluorescent light that can disturb the Still unchanged even though you press and hold the EXIT but-
infrared remote controls. ton for a minimum of 10 seconds.
One or more remote sensors are enabled (only models with
the Remote Sensor Selection function).
Batteries are new and are not reversed in installation.
If present on the remote control, projector selector switch is
not used.
133
8. Appendix
In the space below please describe your problem in detail.
Information on application and environment where your projector is used
Projector Installation environment

Model number: Screen size: inch
Serial No.: Screen type: White matte Beads Polarization
Date of purchase: Wide angle High contrast
Lamp operating time (hours): Throw distance: feet/inch/m
Lamp Mode: Normal Eco Orientation: Ceiling mount Desktop
Information on input signal: Power outlet connection:
Horizontal synch frequency [ ] kHz Connected directly to wall outlet
Vertical synch frequency [ ] Hz Connected to power cord extender or other (the num-
Synch polarity H (+) () ber of connected equipment______________)
V (+) () Connected to a power cord reel or other (the number
of connected equipment______________)
Synch type Separate Composite
Sync on Green
STATUS Indicator: Computer
Steady light Orange Green Manufacturer:
Flashing light [ ] cycles Model number:
Remote control model number: Notebook PC / Desktop
Native resolution:
Refresh rate:
Video adapter:
PC Other:
Projector
DVD player
Signal cable Video equipment

NEC standard or other manufacturers cable? VCR, DVD player, Video camera, Video game or other
Model number: Length: inch/m Manufacturer:
Distribution amplifier Model number:
Model number:
Switcher
Model number:
Adapter
Model number:
134
8. Appendix
TravelCare Guide 5) Problems or damage caused by use in hot or humid places, in

vehicles, boats or ships, etc.
TravelCare - a service for international travelers 6) Problems or damage caused by expendable supplies or devices
connected to the product other than those designated by NEC.
This product is eligible for "TravelCare", NEC's unique international war-
ranty. 7) Problems caused by natural consumption, wear or deterioration
Please note that TravelCare coverage differs in part from coverage un- of parts under normal usage conditions.
der the warranty included with the product. 8) Problems or damage to lamps and other expendable supplies,
included parts or optional parts.
Services offered with TravelCare 9) Other conditions stipulated in the warranty included with the prod-
This warranty allows customers to receive service on their product at uct also apply.
the NEC and NEC-designated service stations in the countries listed
herein when temporarily traveling internationally for business or plea-
NOTE: The product can be used overseas with voltages of 100 to 120V and 200
sure.
to 240V by using a power cable suited for the standards and power source volt-
For details on services offered by the different service stations, please
age of the country in which the product is being used.
refer to the "List of TravelCare Outlets" below.
List of TravelCare Outlets
1 Repair services
The product will be repaired and delivered within 10 business days, This list applies as of April 1, 2004.
not including shipping time. For the most up-to-date information, please refer to the websites of the
During the term of warranty, the cost of maintenance parts, labor service stations in the various countries on the List of TravelCare Out-
costs for repairs and shipping costs within the service station's cov- lets or to the NEC website at http://www.nec-pj.com.
erage area are covered by the warranty.
In Europe
2 Replacement product rental service NEC Europe, Ltd. / European Technical Centre
If the customer desires, he or she can rent a replacement product Address: Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.
while the original product is being repaired. Telephone: +44 1952 237000
Fee: US$200 for 12 days Fax Line: +44 1952 237006
This fee must be paid at the local service station in cash or credit Email Address: [email protected]
card. WEB Address: http://www.neceur.com
The $200 rental fee is non-refundable even if the customer rents it
less than 12 days before returning. (Regions Covered)
The replacement product will be delivered within 3 business days. EU: Austria*, Belgium*, Denmark*, Finland*, France*, Germany*,
If the customer did not return the replacement product within 12 days, Greece*, Ireland*, Italy*, Luxembourg*, The Netherlands*,
the customer will be charged the price of the unit. Portugal*, Spain*, Sweden* and the United Kingdom*
If the customer returned the replacement product in a faulty or dam- EEA: Norway*, Iceland and Liechtenstein
aged condition, the repair cost will be charged to the customer.
Note that this service is not offered in all countries and regions. Please In North America
refer to the "List of TravelCare Outlets". NEC Solutions (America), Inc.
In addition, this replacement product rental service is not offered af- Address: 1250 N. Arlington Heights Road, Suite 400,
ter the product's warranty has expired. Itasca, Illinois 60143, U.S.A.
Telephone: +1 800 836 0655
Term of warranty Fax Line: +1 800 356 2415
Email Address: [email protected]
1 WEB Address: http://www.necvisualsystems.com
a. Upon presentation of the warranty or receipt received upon pur-
chase: (Regions Covered)
Valid for the term indicated on the warranty or the normal term of U.S.A. *, Canada*
warranty for the country of purchase.
In Oceania
b. When only the product is brought in: NEC Australia Pty., Ltd.
Valid for a period of within 14 months of the date of manufacture Address: New South Wales;
indicated by the serial number attached to the product. 184 Milperra Road, Reversby 2212
2 When a product whose term of warranty is expired is brought in: Victoria;
480 Princess Hwy Noble Park 3174
Repairs will be offered for a fee. In this case the customer is not South Australia;
eligible for the replacement product rental service. 84A Richmond Road, Keswick 5035
3 In the following cases, repairs may be charged, even if the product's Queensland;
warranty is still in effect: 116 Ipswich Road, Woollongabba 4102
1) If the term of warranty, model name, serial number and name of Western Australia;
the store of purchase are not indicated on the warranty or have 45 Sarich Court Osborne Park 6017
been altered. Telephone: 131 632 (from domestic)
+61 8 8375 5706 (from overseas)
2) Problems or damage caused by dropping or shocks during ship- Fax Line: +61 8 8375 5757
ment or movement by the customer or by improper handling by Email Address: [email protected]
the customers. WEB Address: http://www.nec.com.au
3) Problems or damage caused by improper usage or unwarrant-
able alterations or repairs by the customer. (Regions Covered)
4) Problems or damage caused by fire, salt damage, gas damage, Australia*, New Zealand
earthquakes, lightning damage, storm or flood damage or other
natural disasters or such external factors as dust, cigarette
smoke, abnormal voltage, etc.
135
8. Appendix
In Asia and Middle East Lenso Communication Co., Ltd.
NEC Viewtechnology, Ltd. Address: 292 Lenso House 4, 1st Floor, Srinakarin Road,
Address: 686-1, Nishioi, Oi-Machi, Ashigarakami-Gun, Huamark, Bangkapi, Bangkok 10240, Thailand
Kanagawa 258-0017, Japan Telephone: +66 2 375 2425
Telephone: +81 465 85 2369 Fax Line: +66 2 375 2434
Fax Line: +81 465 85 2393 Email Address: [email protected]
Email Address: [email protected] WEB Address: http://www.lenso.com
WEB Address: http://www.nec-pj.com
(Regions Covered)
(Regions Covered) Thailand
Japan*
ABBA Electronics L.L.C.
NEC Hong Kong Ltd. Address: Tariq Bin Ziyad Road, P.O.Box 327, Dubai,
Address: 11th Floor, Tower B, New Mandarin Plaza, 14 United Arab Emirates
Science Museum Road, Telephone: +971 4 371800
Tsim Sha Tsui East, Kowloon, Hong Kong Fax Line: +971 4 364283
Telephone: +852 2369 0335 Email Address: [email protected]
Fax Line: +852 2795 6618
Email Address: [email protected] (Regions Covered)
WEB Address: http://www.nec.com.hk United Arab Emirates
(Regions Covered) Samir Photographic Supplies

Hong Kong Address: P.O.Box 599, Jeddah 21421, Saudi Arabia
Telephone: +966 2 6828219
NEC Taiwan Ltd. Fax Line: +966 2 6830820
Address: 7F, No.167, SEC.2, Nan King East Road, Taipei, Email Address: [email protected]
Taiwan, R.O.C.
Telephone: +886 2 8500 1734 (Regions Covered)
Fax Line: +886 2 8500 1420 Saudi Arabia
WEB Address: http://www.nec.com.tw NOTE: In countries designated with an asterisk(*), replacement product rental
service are offered.
(Regions Covered)
Taiwan
NEC Solutions Asia Pacific Pte. Ltd

Address: 401 Commonwealth Drive, #07-02, Haw Par
Technocentre, Singapore 149598
Telephone: +65 6 273 8333
Fax Line: +65 6 274 2226
WEB Address: http://www.nec.com.sg/ap
(Regions Covered)
Singapore
NEC Systems Integration Malaysia Sdn Bhd

Address: Ground Floor, Menara TA One, 22, Jalan P. Ramlee,
50250 Kuala Lumpur, Malaysia
Telephone: +6 03 2164 1199
Fax Line: +6 03 2160 3900
WEB Address: http://www.necmalaysia.com.my
(Regions Covered)
Malaysia
Nautilus Hyosung Inc.

Address: 7th Floor, Cheongdam Building, 52,
Cheongdam-Dong,
Kangnam-Ku, Seoul, Korea 135-100
Telephone: +82 2 510 0234
Fax Line: +82 2 540 3584
(Regions Covered)
South Korea
136
8. Appendix
Date: / / , P-1/ ,
TO: NEC or NEC's Authorized Service Station:

FM:
(Company & Name with signature)
Dear Sir (s),

I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your
following conditions, and also the Service fee will be charged to my credit card account, if I don't return the Loan units within the
specified period. I also confirm following information is correct. Regards.
Application Sheet for TravelCare Service Program
Country,
product purchased :
User's Company Name :
User's Company Address :

Phone No., Fax No. :
User's Name :
User's Address :
Local Contact office :
Local Contact office Address :
User's Model Name :
Date of Purchase :
Serial No. on cabinet :
Problem of units per User :
Required Service : (1) Repair and Return (2) Loan unit
Requested period of Loan unit :
Payment method : (1) Credit Card (2) Travelers Cheque (3) Cash
In Case of Credit Card :

Card No. w/Valid Date :
137
8. Appendix
Condition of your TravelCare Service Program 5. Loan Service Charges and Conditions:
Upon acceptance of this NEC Projector, Customer agrees to assume
Enduser is requested to understand following condition of TravelCare
liability for this loan unit.
Service Program and complete the necessary information on the appli-
cation sheet.
The current cost of use of this loan unit is $200.00 USD for 12 calendar
days.
1. Service Options:
If Customer does not return the unit within the 12 calendar days, Cus-
There are 3 types of "Service" available. Enduser has to understand
tomer will be charged the next highest cost up to and including the full
following condition and is required to fill in the Application Sheet.
list price to Credit Cards, which price will be informed by NEC Autho-
rized Service Stations. Please see the attached listing of contacts for
1) Repair and Return:
each country to arrange for pickup of the loan unit.
The 'Faulty unit' is sent or collected from the customer. It is repaired
and returned within 10 days to the customer, excluding transport time. If you return to their country of origin with the loan unit, you will be
There may have a case, repair and return can't be done by NEC charged additional freight to return the unit to the loaning country.
Authorized Service Station, because of shortage of spare parts due
to same model is not sold in the territory. Thank you for your understanding of this program.
2) Repair and Return with Loan: (This service is limited to some Ser-
vice Stations)
This service is offered to the Enduser, who cannot wait until their unit
is repaired.
The customer can borrow a unit for $200 up to 12 days. Customer
then sends in inoperable unit to nearest NEC Authorized Service
Station for service. In order to prevent collection problem, Enduser is
required to fill in Application Sheet.
Enduser needs to confirm the availability of the Service to NEC Au-
thorized Service Stations.
3) Loan Only:
For this service, NEC Authorized Service Station supplies the cus-
tomer with a loan unit for US$200 up to 12 days. Customer keeps the
inoperable unit and when customer returns home, customer arranges
to have the projector serviced in the home country.
2. Warranty Exclusions:
This program does not apply if the Projector's serial number has been
defaced, modified or removed.
If, in the judgement of NEC Authorized Service Station or its agent the
defects or failures result from any cause other than fair wear and tear or
NEC neglect, or fault including the following without limitation:
1) Accidents, transportation, neglect, misuse, abuse, water, dust, smoke

or default of or by the Customer its employees or agents or any third
party;
2) Failure or fluctuation of electrical power, electrical circuitry, air condi-
tioning, humidity control or other environmental conditions such as
use it in smoking area;
3) Any fault in the attachments or associated products or components
(whether or not supplied by NEC or its agents which do not form part
of the Product covered by this warranty);
4) Any act of God, fire, flood, war, act of violence or any similar occur-
rence;
5) Any attempt by any person other than any person authorized by NEC
to adjust, modify, repair, install or service the product.
6) Any Cross-border charges such as, duty, insurance, tax etc.
3. Charges for Warranty Exclusions and Out of Warranty Case:

In case faulty unit is under warranty exclusions case or under Out of
Warranty period, NEC Authorized Service Station will Inform estimation
of actual service cost to the Enduser with reason.
4. Dead on Arrival (DOA):

Enduser must take this issue up with their original supplier in the coun-
try of purchase.
NEC Authorized Service Station will repair the DOA unit as a Warranty
repair, but will not exchange DOA unit with new units.
Ver. 2 01/2004
138
LIMITED WARRANTY (USA and Canada only)
NEC SOLUTIONS PROJECTOR PRODUCTS HOW YOU CAN GET WARRANTY SERVICE
NEC Solutions (America), Inc. (hereafter NEC Solutions) warrants 1. To obtain service on your product, consult the dealer from whom
this product to be free from defects in material and workmanship you purchased the product.
under the following terms. 2. Whenever warranty service is required, the original dated invoice
(or a copy) must be presented as proof of warranty coverage. In
HOW LONG IS THE WARRANTY order to obtain warranty service, you may be required to describe
NEC Solutions LT265 and LT245 projectors are covered by a two and demonstrate the problem to your dealer or to NEC Solutions.
(2) year limited parts and labor warranty from the date of the first 3. All products returned to NEC Solutions for service MUST have
customer purchase. The lamp when used under normal operationg prior approval. To receive approval or for the name of the
conditions is warranted for 500 hours or 90 days, whichever nearest NEC Solutions authorized service center, call NEC
comes first. Solutions at 800-836-0655.
4. It shall be your obligation and expense to ship the product,
WHO IS PROTECTED freight prepaid, or to deliver it to a NEC Solutions authorized
This warranty may be enforced only by the first purchaser, and is service center, in either the original package or a similar pack-
not transferable. age affording an equal degree of protection.
5. In the event a product is returned to NEC Solutions for warranty
WHAT IS COVERED AND WHAT IS NOT COVERED service, and it is determined that there is no product defect or that
Except as specified below, this warranty covers all defects in the product condition is not covered by this limited warranty, a
material or workmanship in this product. diagnostic service fee may be charged to the customer.
NEC SOLUTIONS LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITATION OF IMPLIED WARRANTIES
LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY,
AT NEC SOLUTIONS OPTION. REPLACEMENT PRODUCTS MAY NEC SOLUTIONS MAKES NO OTHER WARRANTIES, EXPRESS
BE NEW OR RECONDITIONED PRODUCTS, AND REPLACEMENT OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
PARTS MAY BE NEW OR SERVICEABLE USED PARTS. The follow- WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
ing are not covered by the limited warranty and NEC Solutions FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED WARRAN-
shall not be liable for: TIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS
AND DURATION OF THIS LIMITED WARRANTY.
1. Any product which is not distributed in the U.S.A. or Canada
by NEC Solutions or which is not purchased, installed, and EXCLUSION OF DAMAGES
operated in the U.S.A or Canada. NEC SOLUTIONS LIABILITY FOR ANY DEFECTIVE PRODUCT IS
2. Any product on which the serial number has been defaced, LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
modified or removed. AT NEC SOLUTIONS OPTION. NEC SOLUTIONS SHALL NOT
3. Normal decrease in lamp light output over time. BE LIABLE FOR:
4. Damage, deterioration or malfunction resulting from: 1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS
a. Accident, misuse, abuse, neglect, improper ventilation, fire, IN THIS PRODUCT, DAMAGES BASED UPON INCONVE-
dust, smoke, water, lightning or other acts of nature, unau- NIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME,
thorized product modification, or failure to follow instruc- COMMERCIAL LOSS; OR
tions supplied with the product. 2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSE-
b. Repair or attempted repair by anyone other than a NEC QUENTIAL OR OTHERWISE.
Solutions authorized service center.
c. Any shipment of the product (claims must be presented to HOW STATE LAW RELATES TO THE WARRANTY
the carrier). SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
d. Removal or installation of the product. AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE
e. Any other cause which does not relate to a product defect. EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-
f. Use of the product beyond normal operating conditions. TIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLU-
Normal operating conditions are defined as product use SIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY
not in excess of 8 hours per day and 260 days per year. GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE
5. Cartons, carrying cases, shipping cases, batteries, external OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
cabinets, magnetic tapes, or any accessories used in connec-
tion with the product. FOR MORE INFORMATION, CONTACT:
6. Service required as a result of third party components. NEC SOLUTIONS (AMERICA), INC.
1250 N. Arlington Heights Road
WHAT NEC SOLUTIONS WILL PAY FOR Itasca, Illinois 60143-1248
NEC Solutions will pay labor and material expenses for covered TELEPHONE 800-836-0655
items, but NEC Solutions will not pay for the following: www.necvisualsystems.com
1. Removal or installation charges. Customers are cautioned that product performance is affected by
2. Costs of technical adjustments, set-up, maintenance, or adjust- system configuration, software, the application, customer data,
ment of user controls. and operator control, among other factors. While NEC Solutions
3. Payment of shipping and related charges incurred in returning products are considered to be compatible with many systems, the
the product for warranty repair. specific functional implementation by the customers of the prod-
uct may vary. Therefore, the suitability of a product for a specific
purpose or application must be determined by the customer and
is not warranted by NEC Solutions.
Printed on recycled paper Printed in Japan

7N8P4841
Ver1. 8/04
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
U.S. Responsible Party: NEC Solutions (America), Inc.

Address: 1250 N. Arlington Heights Road
Itasca, Illinois 60143
Tel. No.: (630) 467-5000
Type of Product: Projector

Equipment Classification: Class B Peripheral
Models: LT265/LT245
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
NEC LT265 GOV/LT245 GOV
Users Manual Supplement
This document provides information exclusive to the LT265GOV/LT245GOV. For detailed

product and usage information on the projector, read the supplied user documents: CD-
ROM, Important Information and Quick Setup Guide.
Selecting Power-saving in Standby Mode

Select Advanced menu Setup Installation Standby Mode
The projector has two standby modes: Normal and Power-

saving.
Power-saving mode is the mode that allows you to put the
projector in the power-saving condition which consumes less
power than the Normal mode. The projector is preset for
Normal mode at the factory.
NOTE:
The MONITOR OUT function is not available during Power-saving mode.
Control through the PC Control connector and LAN mode is not available during Power-saving
mode. For PC control and LAN mode of the projector it is recommended to leave the projector in the
Normal mode.
Normal mode .................. Power indicator: Orange light/ Status indicator: Green light
Power-saving mode ........ Power indicator: Orange light/Status indicator: Off
See back page for a complete table of indicator messages.
Power Consumption
Power consumption 12W in Normal mode; 0.7W in Power-saving mode
Setting Closed Caption

Select Basic menu or Advanced menu Setup Tools Closed Caption
This option sets several closed caption modes that allows text
to be superimposed on the projected image.
CAPTION 1-4 ......... Text is superimposed.

TEXT 1-4 ............... Text is displayed in full screen.
OFF ........................ This exits the closed caption mode.
Indicator Messages
Power Indicator
Off The main power is off
Blinking light Green 0.5 sec On, The projector is getting ready to turn on. Wait for a moment.
0.5 sec Off
Green 2.5 sec On, Off Timer is activated.
0.5 sec Off
Orange 0.5 sec On, The projector is cooling down. Wait for a moment.
0.5 sec Off
Steady light Green The projector is turned on.
Orange The projector is in Normal standby or
Power-saving standby mode.
Status Indicator
Off Normal
Blinking light Red 1 cycle (0.5 sec On, Lamp cover error Replace the lamp cover correctly.
2.5 sec Off)
2 cycle (0.5 sec On, Temperature error The projector is overheated. Move
0.5 sec Of) the projector to a cooler location.
3 cycle (0.5 sec On, Power error Power unit will not work correctly.
0.5 sec Off)
4 cycle (0.5 sec On, Fan error Fans will not work correctly.
0.5 sec Off)
6 cycle (0.5 sec On, Lamp error Lamp fails to light. Wait a full
0.5 sec Off) minute and then turn on again.
Green Re-firing the lamp The projector is re-firing.
Orange 1 cycle(0.5 sec On, Network conflict Network will not work correctly.
2.5 sec Off)
Steady light Orange Cabinet button is locked You have pressed cabinet button
when Cabinet Button is locked.
Green The projector is in Normal standby mode.
Lamp Indicator
Off Normal
Blinking light Red Lamp has reached its end of life. Lamp Replace the lamp.
replacement message will be displayed.
Steady light Red Lamp has been used beyond its limit. The Replace the lamp.
projector will not turn on until the lamp is
replaced.
Green Lamp mode is set to Eco mode
Printed on recycled paper Printed in Japan

7N8P5171

NEC LT265 Projector Manual

Uploaded by

Copyright:

Available Formats

NEC LT265 Projector Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NEC LT265 Projector Manual

Uploaded by

Copyright:

Available Formats

Portable Projector

DOC Compliance Notice (for Canada only)

Acoustic Noise Information Ordinance-3. GSGV (for Germany only):

This label is underneath the remote control.

WARNING TO CALIFORNIA RESIDENTS:

Copyright NEC Viewtechnology, Ltd. 2004

RF Interference (for USA only)

Reorient or relocate the receiving antenna.

Fire and Shock Precautions

2. Installation and Connections .................................................... 13

3. Projecting an Image (Basic Operation) ................................. 27

4. Convenient Features .................................................................... 38

Correcting Horizontal and Vertical Keystone Distortion (Cornerstone) ....................... 43

5. Using the Viewer ........................................................................... 62

6. Using On-Screen Menu ................................................................ 71

7. Maintenance ................................................................................. 117

8. Appendix ........................................................................................ 122

What's in the Box? ....................................................... 2

Introduction to the Projector ........................................ 3

Part Names of the Projector ........................................ 5

Part Names of the Remote Control ........................... 10

What's in the Box?

Remote control Batteries (AAA 2) Remote mouse receiver

Power cable RGB/VGA signal cable

For North America only Security sticker

Introduction to the Projector

Congratulations on Your Purchase of the LT265/LT245 Projector

Features youll enjoy on the LT265/LT245:

Free downloadable Software Geometric Correction Tool 2.0.

About this user's manual

IBM is a trademark or registered trademark of International Business Machines Corporation.

Part Names of the Projector

Ventilation (outlet) Ventilation (inlet)

Adjustable Tilt Foot Lever Carrying Handle

Carrying the Projector

Monaural Speaker (2W)

SOURCE AUTO ADJUST

2. STATUS Indicator 8. EXIT Button

5. AUTO ADJUST Button

Terminal Panel Features

PC CARD LAN USB

1. COMPUTER 1 IN / Component Input Connector 6. S-VIDEO IN Connector (Mini DIN 4 Pin)

Terminal Panel Features

PC CARD LAN USB

12. PC CARD Eject Button

13. PC CARD Slot

Part Names of the Remote Control

1. Infrared Transmitter/Laser Pointer

21 VOLUME HELP 27 4. POWER OFF Button

8. PAGE UP/DOWN Buttons

10. Select Button 23. FREEZE Button

11. ENTER Button 25. ASPECT Button

12. EXIT Button 26. VIEWER Button

16. S-VIDEO Button

17. COMPUTER 1 Button

18. COMPUTER 2 Button

19. AUTO ADJ. Button

20. LAN Button

21. PIC-MUTE Button

22. VOLUME +/ Buttons