Scribd Logo
Upload

Welcome to Scribd!

  • 404 views

    Submarine Design

    Uploaded by

    Ehsan Amiri
    The document summarizes the design of an exploration submarine intended to reach depths of 4 to 5 miles below sea level. Key aspects of the design include a 12 foot diameter hull divided into compartments for controls, research, and engines. The hull material, AISI 4340 steel, was selected for its strength at high pressures. Finite element modeling and buckling analysis were used to iteratively determine the needed hull thickness and internal stiffeners to support a maximum depth of 4.9 miles, as verified through preliminary analysis showing a buckling strength of 11,219 psi.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Submarine Design

    Uploaded by

    Ehsan Amiri
    404 views2 pages
    The document summarizes the design of an exploration submarine intended to reach depths of 4 to 5 miles below sea level. Key aspects of the design include a 12 foot diameter hull divided into compartments for controls, research, and engines. The hull material, AISI 4340 steel, was selected for its strength at high pressures. Finite element modeling and buckling analysis were used to iteratively determine the needed hull thickness and internal stiffeners to support a maximum depth of 4.9 miles, as verified through preliminary analysis showing a buckling strength of 11,219 psi.

    Original Description:

    Submarine Design

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document summarizes the design of an exploration submarine intended to reach depths of 4 to 5 miles below sea level. Key aspects of the design include a 12 foot diameter hull divided into compartments for controls, research, and engines. The hull material, AISI 4340 steel, was selected for its strength at high pressures. Finite element modeling and buckling analysis were used to iteratively determine the needed hull thickness and internal stiffeners to support a maximum depth of 4.9 miles, as verified through preliminary analysis showing a buckling strength of 11,219 psi.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    404 views2 pages

    Submarine Design

    Uploaded by

    Ehsan Amiri
    The document summarizes the design of an exploration submarine intended to reach depths of 4 to 5 miles below sea level. Key aspects of the design include a 12 foot diameter hull divided into compartments for controls, research, and engines. The hull material, AISI 4340 steel, was selected for its strength at high pressures. Finite element modeling and buckling analysis were used to iteratively determine the needed hull thickness and internal stiffeners to support a maximum depth of 4.9 miles, as verified through preliminary analysis showing a buckling strength of 11,219 psi.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    1 Submarine Design

    Our deep sea exploration submarine was designed with the intent to have a maximum crew capacity of 12 and a depth capability of 4 to 5 miles. The general layout would be similar to a military submarine but on a much smaller scale. To support the crew and all the necessary controls and instrumentation, the mean hull diameter was set at 12 ft. The main cylindrical section was divided into the fwd, mid and rear compartments which are the control room, the research and analysis room and the engine room, respectively. Sonars and fwd ballast tanks are situated in the nose of the submarine whereas the propulsion system and aft ballast tanks are mounted inside the conical tail section. Two vertical and two horizontal fins that are welded onto the tail provide stability and maneuverability. The fwd and aft bulkheads separate the nose and tail section from the main compartments. Internals stiffeners welded onto the hull provide additional strength for the submarine.

    A very strong material is required if our submarine is to withstand the crushing pressures of the ocean floor. As a result, AISI 4340 Steel, oil quenched at 845C and tempered at 425C, was selected. Although its tensile strength is higher at lower temperatures, which is typical of the ocean floor environment, room temperature properties were conservatively used for additional safety margin.

    With the general layout defined and material selected, some preliminary analyses were required in order to size the hull thickness as well as the internal stiffeners. A finite element model was created and an Eigenvalue Buckling Analysis was conducted to determine the critical buckling pressure (Pcrit). The critical buckling pressure was then used to back calculate the depth capability using Bernoullis equation (Eqn 1).

    P = Po + gh

    (Eqn 1)

    where

    P = Critical Buckling Pressure Po = Atmospheric Pressure 1

    = Density of Seawater g = Gravitational Acceleration h = Ocean Depth

    Several iterations were performed until reasonable sizes for the hull and internal stiffeners were determined such that the 4 to 5 mile depth capability of the submarine can be achieved. (A thickness of 1 ft. was prescribed for the bulkheads and remained constant through each iteration) The final dimensions of our deep sea exploration submarine structure as a finite element model is shown in Figure 1 below. Preliminary analysis shows that its buckling strength is 11,219 psi, yielding a maximum ocean depth capability of 4.9 miles.

    Figure 1 Submarine Design Configuration and Dimensions

    You might also like