Scribd
Upload
95 views1 page

Wrc-Canr-Df-Xx Series 4 Quick Start Guide: Sold and Supported by Prosoft Technology, Inc

Uploaded by

Mauricio Oliveira

Guia Rapido Rede CAN

Copyright:

Attribution Non-Commercial (BY-NC)
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

Wrc-Canr-Df-Xx Series 4 Quick Start Guide: Sold and Supported by Prosoft Technology, Inc

Uploaded by

Mauricio Oliveira
95 views1 page
Guia Rapido Rede CAN

Original Title

Rede CAN

Copyright

© Attribution Non-Commercial (BY-NC)

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

Guia Rapido Rede CAN

Copyright:

Attribution Non-Commercial (BY-NC)
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
95 views1 page

Wrc-Canr-Df-Xx Series 4 Quick Start Guide: Sold and Supported by Prosoft Technology, Inc

Uploaded by

Mauricio Oliveira
Guia Rapido Rede CAN

Copyright:

Attribution Non-Commercial (BY-NC)
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 1

WRC-CANR-DF-xx Series 4 Quick Start Guide

Western Reserve Controls, Inc. Copyright 2012 WRC

Sold and Supported by ProSoft Technology, Inc. www.prosoft-technology.com


Use this Quick Start Guide to quickly and easily install your CAN-Bus Fiber Optic Extenders in your system, follow the instructions below. For more details please see the WRC-CANR Users Manual at http://www.prosofttechnology.com/prosoft/products/network_repeaters_extenders/devicenet_canopen_sae_j1939/wrc_canr_df. WARNING: Series IV F/W Revision 4.002 is not backward compatible. NOTE: CANR-DF units are sold in identical pairs, including two (2) extenders. You will need two (2) multi-mode fiber cable lengths for use with a CANR-DF-DN pair, or two (2) single-mode fiber cable lengths for use with a CANR-DF-SM pair, terminated with ST male connectors. 1. Leave the DIP switches in the factory setting on both units in the FF or all OPEN positions for Autobaud for DeviceNet baud rates (125K, 250K or 500K). If you are not using a DeviceNet baudrate, or you desire to manually set a fixed baudrate, set the switches (matching on both units) according to the table below. For more on switch settings see the WRC-CANR Users Manual.
Baudrate 125K 250K 500K Autobaud 9.6K 10K 20K 40K 50K 100K 800K 1M Remote Autobaud Switch setting (numerical) 0 1 2 3 4 5 6 7 8 9 10 11 15 12-14 Position 1 Position 5 CLOSED CLOSED CLOSED CLOSED CLOSED CLOSED CLOSED CLOSED OPEN OPEN OPEN OPEN OPEN Position 2 Position 6 CLOSED CLOSED CLOSED CLOSED OPEN OPEN OPEN OPEN CLOSED CLOSED CLOSED CLOSED OPEN Position 3 Position 7 CLOSED CLOSED OPEN OPEN CLOSED CLOSED OPEN OPEN CLOSED CLOSED OPEN OPEN OPEN Position 4 Position 8 CLOSED OPEN CLOSED OPEN CLOSED OPEN CLOSED OPEN CLOSED OPEN CLOSED OPEN OPEN Meaning Fixed Fixed Fixed Autobaud for DeviceNet Bauds (125k, 250k, 500k) Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Takes baud rate from the opposite end device. If both sides are remote, Autobaud from either side. Autobaud

ALL OTHER SWITCH POSITIONS

2. Using on-board jumper W1, terminate each side of the CAN-Bus network, as appropriate. (This is especially critical at the higher baud rates.) For trunk lines, install W1 on both units. For a drop line install only the W1 jumper on the unit on the opposite network side of the trunk line.

3. Connect the fiber cables to the fiber connectors on one unit. Make sure they are clearly marked on both ends to differentiate between the two lines. 4. Make sure that there is power on the CAN-Bus Network and plug in the Network cable (a 5-pin round female MINI connector) into the CAN-Bus Extender. 5. The CANR-DF Extender will undergo its initialization sequence, flashing the LEDs. After approximately 5 seconds, the Module Status LED (labeled MS) will go on solid green and network LEDs (labeled NSA and NSB) will flash green. The DGN LED will be solid red until the fiber cables are connected to the other CANR and both CANRs are powered up. 6. Repeat steps 1-5 above for the second CANR-DF. Note: Be sure to connect the fiber from the TX port on one device to the RX port on the other. 7. Connect the desired network devices to both sides of the copper CAN bus. 8. Both Network A and B Status LEDs (NSA and NSB) will go on solid on each unit once a valid CAN message is received into either side of the Extender and the baudrate auto-detect has been successfully performed. 9. You may observe that the small green LEDs marked RXF and TXF, next to the fiber ports, illuminate when data is received or transmitted. The CAN-Bus Extender is now operating on the network and is ready to repeat messages from either Network A or Network B. Western Reserve Controls 1485 Exeter Road, Akron OH 44306 www.wrcakron.com

You might also like