Scribd
Upload
404 views1 page

Adavanced Control Systems

This document outlines the course objectives and units of study for an Advanced Control Systems elective course. The course covers state space analysis, controllability and observability tests, describing function analysis for nonlinear systems, phase-plane analysis, stability analysis using Lyapunov's methods, modal control design using state feedback and observers, calculus of variations, and optimal control formulation and methods for minimum time, energy, and output regulation problems. The course references two primary textbooks on modern control systems theory and digital control and state variable methods.

Uploaded by

scribdcurrenttext
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
404 views1 page

Adavanced Control Systems

This document outlines the course objectives and units of study for an Advanced Control Systems elective course. The course covers state space analysis, controllability and observability tests, describing function analysis for nonlinear systems, phase-plane analysis, stability analysis using Lyapunov's methods, modal control design using state feedback and observers, calculus of variations, and optimal control formulation and methods for minimum time, energy, and output regulation problems. The course references two primary textbooks on modern control systems theory and digital control and state variable methods.

Uploaded by

scribdcurrenttext
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD IV Year B.Tech EEE.

II-Sem T P C 4+1* 0 4 ADVANCED CONTROL SYSTEMS (ELECTIVE III) Objective : This subject deals with state space, describing function, phase plane and stability analysis including controllability and observability. It also deals with modern control and optimal control systems. UNIT I STATE SPACE ANALYSIS State Space Representation, Solution of State Equation, State Transition Matrix, Canonical Forms Controllable Canonical Form, Observable Canonical Form, Jordan Canonical Form. UNIT II CONTROLLABILITY AND OBSERVABILITY

Tests for controllability and observability for continuous time systems Time varying case, minimum energy control, time invariant case, Principle of Duality, Controllability and observability form Jordan canonical form and other canonical forms. UNIT III DESCRIBING FUNCTION ANALYSIS

Introduction to nonlinear systems, Types of nonlinearities, describing functions, describing function analysis of nonlinear control systems. UNIT-IV PHASE-PLANE ANALYSIS Introduction to phase-plane analysis, Method of Isoclines for Constructing Trajectories, singular points, phaseplane analysis of nonlinear control systems. UNIT-V STABILITY ANALYSIS Stability in the sense of Lyapunov., Lyapunovs stability and Lypanovs instability theorems. Direct method of Lypanov for the Linear and Nonlinear continuous time autonomous systems. UNIT VI MODAL CONTROL

Effect of state feedback on controllability and observability, Design of State Feedback Control through Pole placement. Full order observer and reduced order observer. UNIT-VII CALCULUS OF VARIATIONS Minimization of functionals of single function, Constrained minimization. Minimum principle. Control variable inequality constraints. Control and state variable inequality constraints. Euler Lagrangine Equation. UNIT VIII OPTIMAL CONTROL

Formulation of optimal control problem. Minimum time, Minimum energy, minimum fuel problems. State regulator problem. Output regulator problem. Tracking problem, Continuous-Time Linear Regulators. TEXT BOOKS: 1. Modern Control System Theory by M. Gopal, New Age International Publishers, 2
nd

edition, 1996

REFERENCE BOOKS: 1.Modern Control Engineering by K. Ogata, Prentice Hall of India, 3 edition, 1998. 2.Control Systems Engineering by I.J. Nagarath and M.Gopal, New Age International (P) Ltd. 3.Digital Control and State Variable Methods by M. Gopal, Tata Mc Graw-Hill Companies, 1997. 4.Systems and Control by Stainslaw H. Zak , Oxford Press, 2003.
rd

You might also like