Scribd
Upload
55 views

Product Photo: 27mm×13mm×2mm

This document provides information about a Bluetooth module including: 1. It lists key features such as a typical -80dBm sensitivity, up to +4dBm RF transmit power, integrated 15-bit linear audio codec, and low power 1.8V operation. 2. It describes package options and electrical specifications. 3. It provides a block diagram of the module showing components like the radio transceiver, baseband, ROM, and I/O interfaces.

Uploaded by

Uchija Darck Khronos
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
55 views

Product Photo: 27mm×13mm×2mm

This document provides information about a Bluetooth module including: 1. It lists key features such as a typical -80dBm sensitivity, up to +4dBm RF transmit power, integrated 15-bit linear audio codec, and low power 1.8V operation. 2. It describes package options and electrical specifications. 3. It provides a block diagram of the module showing components like the radio transceiver, baseband, ROM, and I/O interfaces.

Uploaded by

Uchija Darck Khronos
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

1.

Product Photo

27mm13mm2mm

2Feature z Radio Transceiver Typical 80dBm sensitivity Up to +4dBm RF transmit power with power level control Fully Qualified Bluetooth V2.0+EDR(Enhanced Data Rate) 2Mbps Modulation Integrated 15-bit Linear 8KHz Sample Frequency Audio CODEC in one chip Internal 6Mbit ROM Low Power 1.8V Operation Integrated Switch-Mode Regulator (DC To DC) Integrated Battery Charger With Programmable Current PIO control Standard HCI(UART or USB) 4.2V Tolerant LED Drivers With Intensity Control UART interface with programmable baud rate Basic module without antenna Basic module as SMD type With Audio Out & Audio in z Package option Edge connector

3.

Summary of Benefit

z Complete Bluetooth Solution Complete 2.4GHz radio transceiver and baseband CSR Bluecore 04-Audio ROM, single chip bluetooth system with CMOS technology Adaptive frequency hopping feature (AFH) Smallest footprint, 27mmX13mm Simplify overall design/development cycle Full speed Class 2 bluetooth operation Class I support using external power amplifier z z z z Low power standby modes to enable high efficient power management High performance radio transceiver Low overall system cost Application Mouse Automotive Hands-Free Kits Cordless headsets z Software Support CSR bluetooth stack Design for Client

4Device Terminal Function PIN Name GND PIN #


13 21 22

Pad type
VSS

Description
Ground pot Integrated 3.3V (+) supply with

Note

3.3 VCC AIO0 AIO1 PIO0 PIO1 PIO2 PIO3 PIO4 PIO5 PIO6 PIO7 PIO8 PIO9 PIO10 PIO11 RESETB

12

3.3V

On-chip linear regulator output within 3.15-3.3V

9 10 23 24 25 26 27 28 29 30 31 32 33 34 11

Bi-Directional Bi-Directional Bi-Directional RX EN Bi-Directional TX EN Bi-Directional Bi-Directional Bi-Directional Bi-Directional Bi-Directional Bi-Directional Bi-Directional Bi-Directional Bi-Directional Bi-Directional CMOS output,

Programmable input/output line Programmable input/output line Programmable input/output line, control output for LNA(if fitted) Programmable input/output line, control output for PA(if fitted) Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line

UART_RTS

tri-stable with weak internal pull-up CMOS input with

UART request to send, active low

UART_CTS

weak internal pull-down

UART clear to send, active low

Issue Date :12/28/20085:10:52 PM

CMOS input with

UART_RX

weak internal pull-down CMOS output, Tri-stable with weak internal pull-up CMOS input with

UART Data input

UART_TX

UART Data output

SPI_MOSI

17

weak internal pull-down CMOS input with

Serial peripheral interface data input Chip select for serial peripheral interface, active low

SPI_CSB

16

weak internal pull-up CMOS input with

SPI_CLK

19

weak internal pull-down CMOS input with

Serial peripheral interface clock

SPI_MISO USB_USB_+ 1.8V PCM_CLK PCM_OUT PCM_IN PCM_SYNC

18

weak internal pull-down

Serial peripheral interface data Output

15 20 14 5 6 7 8

Bi-Directional Bi-Directional Output Dc1.8v Bi-Directional CMOS output CMOS Input Bi-Directional Synchronous PCM data clock Synchronous PCM data output Synchronous PCM data input Synchronous PCM data strobe

5.

Electrical Specification: z Eecommended Operating condition

z Transmitter

6.

Schematic Diagram

7. Block Diagram

Fig 1

Programming and Freq. Alignment Test Procedure

Fig 2

RF Parameter Test procedure

13

14

You might also like