Scribd Logo
Upload

Welcome to Scribd!

  • 365 views

    BLDC 5015a

    Uploaded by

    roozbehxox
    The DC brushless driver BLDC-5015A user manual provides specifications and operating instructions for the driver. It can run BLDC motors with speeds up to 8000 RPM using SPWM control. It has inputs for speed regulation via potentiometer or analog voltage, and inputs to control direction, braking, and more. The manual describes electrical parameters, wiring diagrams, terminal functions, and precautions for safe operation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    BLDC 5015a

    Uploaded by

    roozbehxox
    365 views5 pages
    The DC brushless driver BLDC-5015A user manual provides specifications and operating instructions for the driver. It can run BLDC motors with speeds up to 8000 RPM using SPWM control. It has inputs for speed regulation via potentiometer or analog voltage, and inputs to control direction, braking, and more. The manual describes electrical parameters, wiring diagrams, terminal functions, and precautions for safe operation.

    Original Title

    BLDC-5015A

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The DC brushless driver BLDC-5015A user manual provides specifications and operating instructions for the driver. It can run BLDC motors with speeds up to 8000 RPM using SPWM control. It has inputs for speed regulation via potentiometer or analog voltage, and inputs to control direction, braking, and more. The manual describes electrical parameters, wiring diagrams, terminal functions, and precautions for safe operation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    365 views5 pages

    BLDC 5015a

    Uploaded by

    roozbehxox
    The DC brushless driver BLDC-5015A user manual provides specifications and operating instructions for the driver. It can run BLDC motors with speeds up to 8000 RPM using SPWM control. It has inputs for speed regulation via potentiometer or analog voltage, and inputs to control direction, braking, and more. The manual describes electrical parameters, wiring diagrams, terminal functions, and precautions for safe operation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    DC BRUSHLESS DRIVER BLDC-5015A user manual

    Features SPWMSpeed/Current alike close loop technology, smooth rotation l Smooth torque output within speed range (8000 rpm Max.) l 175 Max. speed regulation ratio l 60/300/120/240Electrical angle adjustable l Speed regulation potentiometer adjust / Analog input l Run/StepQuick BrakeCW/CCW rotation shift l Speed outputAlarm outputO.C. l Over currentover voltagestallmissing speed Alarm Parameters Electrical ParametersTj25C Power Current output Driving mode Insulation Res. Dielectric Strength Weight

    YK YK YK YK YK

    Ambient requirement

    Cooling Self cool Environment Keep away from oil, dust, and acid gas Temperature 0C50C 80RH Humidity 5.7m/s2Max. Vibration Storage temp. 20C125C

    Function description l Power Supply: DC+ ; DCVoltage: 24 50DC normally Linear Power Supply applied appendixripple voltage higher than 50V may damage driver. The output current of LPS shall be 60more than that of driver. In case of switching power supply(strongly recommended)applied, please pay attention to the current shall meet motors current. Attention: incorrect connection may cause driver damaged.

    E T T T TT

    2450VDC, Capacityup to motors Rated 15APeak 45A3s SPWM 500M 500V/Minute About 300g

    C EC EC EC EC
    1

    H H H H H

    T T T TO OT MO MO MO MO M

    R OR OR OR OR

    l Speed regulation choice(RV ; AVI) 1. Setup speed by potentiometer (RV).The dipswitch SW2 must be ON status to enable this function. CW rotate the potentiometer will increase speed. CCW- speed down. 2. Setup speed by analog input (AVI). The dipswitch SW2 must be OFF status to enable this function.AVI terminal accept 05V voltage or PWM signal from controllerAVI terminal with input resistance of 100Kcurrent consumption5mA Reference table SW2 Command to Speed adjust CWspeed up ON RV CCWspeed down 05V analog input OFF AVI OFF AVI PWM Comman 05V volage 1KHz duty cycle Current 5mA

    YK YK YK YK YK
    !

    Only one of above two modes can be used to adjust speed (another mode shall be enabled). Once AVI terminal applied, (RV) potentiometer shall be CCW turned to Min. position PWM signal are 5V TTL level. l Run/StopENBL ENBL terminal is applied to control motor Run/StopCommon positive terminal is 5V. Optical coupler short circuit make motor run, it open circuit make motor stop.

    See below circuit

    l CW/CCW RotationF/R F/R terminal is applied to shift motor rotate direction, common positive terminal is5V. Motor run in CCW when optical coupler is short circuit, motor run in CW when optical coupler is open circuit.
    2

    E T T T TT

    C EC EC EC EC

    H H H H H

    T T T TO OT MO MO MO MO M

    R OR OR OR OR

    Attentiondont change the connection sequence of phase wires of motor to shift rotate direction. l Motor Brake CommandBRK BRK terminal applied to stop rotation quickly. Motor will stop normally within 50ms. But inertia of load cant exceed 2 times of motor inertia, otherwise brake will cause driver alarm. Time of acceleration and deceleration must be put into controller in case of too big load inertia, And please dont use brake function in such condition. The optical coupler short circuit will brake motoroptical coupler open circuit release motor to run. l Setup different electrical angle Dipswitch SW1 can be setup to fit motors with different electrical angel SW1 ON 120or 240hall signalthey are in opposite rotation direction OFF 60or 300hall signal, they are in opposite rotation direction l Motor rotation speed outputSPEED Pulse generated by driver are proportioned with motor speed,(isolated O.C. output) it can be increased to be a random level. 6 multiple frequency processed output.

    YK YK YK YK YK

    Motor speed60SPEED(pulse freq.)/pulses per rev. of motorp.p.r motor pole pairs6

    l Alarm output(ALM

    Driver will enter protection mode and stop motor running in case of OVER CURRENT, OVER VOLTAGE, SHORT CIUCUIT, MOTOR STALL ariseLED on driver will be light, and ALM signal will be available. Please cut off drivers power supplycheck wiring and voltage. High voltage is not permitted for big inertia motor, as it may cause run/stop frequently and over voltage alarm. Circuit of this function refer to pic. 2.

    E T T T TT

    C EC EC EC EC
    3

    H H H H H

    T T T TO OT MO MO MO MO M

    R OR OR OR OR

    l Terminals description Terminal mark Description DC+DCVoltage supply to driver UVW To motor leads. Make sure correct connection to motor leads. REF+REF-HU Hall sensor connection REF+ REF- are for hall power HVHW supply. Make sure correct connection to halls. AVIENBLF/RControls inputsee below picture BRKVcc SPEEDALM Signal output(O.C. l Wiring Diagram

    YK YK YK YK YK

    E T T T TT

    C EC EC EC EC
    4

    H H H H H T T T TO OT MO MO MO MO M R OR OR OR OR

    YK YK YK YK YK

    E T T T TT

    C EC EC EC EC

    H H H H H

    T T T TO OT MO MO MO MO M

    R OR OR OR OR

    You might also like