Tank Inspection Handbook

This is the fourth edition of the Tank Container Inspection Handbook. This handbook will be updated from time to time.

CONTENTS SECTION 1 Safety

SECTION 2 Definitions and Cleaning Terminology Completion of Tank Repair Estimate Completion of Internal Shell Condition Chart Tank ISO location Codes Container ISO Codes ISO Damage Codes ISO Repair Codes Cost Allocation SECTION 4 Inspection Procedures Post Estimate Inspection Joint Survey Post Repair Combined Post-Repair & On-Hire Supplementary Estimate Lessee On-Hire Survey Pre-delivery Inspection GQ Sticker Lessee Refuse Cost Report (3)

(9)

SECTION 3

(21) (29) (32) (37) (48) (52) (55) (59) (62) (63) (64) (67) (67) (68) (70) (71) (72)

SECTION 5

Identification of Manufacturers' Defects (73) Procedure for Reporting Manufacturers' Defects Warranty Report - New Defects (78) (81)

SECTION 6

Identification of Frequent Misuse of Tank Containers (83) Improper Repairs (89)

SECTION 7 SECTION 8

Inspection Guidelines for Tank Containers (ACC) (93) Convention for Safe Containers (CSC) (139)

SECTION 9

For further information please contact: Engineering and Technical Services Department GE SeaCo Services Ltd. 21 St Thomas Street London SE1 9RY, UK Tel: Fax: Email Website + 44 (0)20 7939 5600 + 44 (0)20 7939 5650 ets@GE SeaCo.com www.GE SeaCotanks.com

All advice and information contained within this publication is provided in good faith. However, the authors and publishers can accept no liability or responsibility for any errors, omissions or inaccuracies contained herein. GE SeaCo recommends that strict observance of all the relevant statutory codes of practice is maintained and that routine servicing and inspection procedures are undertaken by competent personnel and trained in safety procedures. July 2009

Section 1

SAFETY

Section 1 - Safety Contents of Section

Safe inspection procedures and practice. Specific Inspection Hazards (5) (6)

DO NOT OPERATE ANY VALVES /FITTINGS OR ENTER ANY TANK WHICH DOES NOT POSSESS A VALID SAFETY DOCUMENT. SEE SECTION 2 FOR DEFINITION OF A VALID SAFETY DOCUMENT.

INTRODUCTION Inspections should be carried out in compliance with international and local laws including health and safety, the workplace, inspection and working conditions. The following is for guidance only. SAFE INSPECTION PROCEDURES AND PRACTICE. Tank containers are designed to transport cargoes which may be dangerous. Characteristics and safety hazards associated with specific cargoes are available from manufacturers on the Material Safety Data Sheets (MSDS). Cargoes might be transported under a blanket layer of inert gas such as nitrogen. An inert gas cannot support human life; breathing any gas mixture possessing less than 19.5% of oxygen is likely to cause suffocation (asphyxiation). Prior to a thorough cleaning and ventilation, tanks may not possess adequate oxygen to sustain life or may contain harmful or explosive vapours hazardous to one's health. Do not operate any valves/fittings or enter any tank which does not possess a valid safety document

Personnel must not enter any tank container until a tank entry permit has been completed. Entry permits are designed to help ensure compliance with confined space entry laws and regulations of all governments having jurisdiction (nation, state/province, locality, etc.). Before entering a tank the inspector must: Check the last cargo and safety data (MSDS) and take appropriate action. Check that the tank has been cleaned. Check that the tank has been adequately ventilated with fresh air to ensure a minimum oxygen content of 19%. Check the tank atmosphere to determine the absence of explosive or flammable vapour or gas. Check that an attendant who has full knowledge of the time of entry is stationed outside the tank in the immediate vicinity and that the inspector and attendant are equipped with all safety and rescue equipment required by all applicable laws and regulations.

SPECIFIC INSPECTION HAZARDS Personnel must be mindful of certain specific hazards which could potentially arise when inspections or testing of containers are performed. These include but are not limited to: Asphyxiation or poisoning upon entry into an unclean tank or a tank possessing insufficient oxygen.

Sudden release of pressure from discharge valves or manlid if opened while tank is under pressure. Avoid standing in front of fittings, openings or over the manlid if the possibility of sudden pressure discharge exists. Personnel should depressurise the tank vessel by carefully operating the airline valve. Do not depressurise the tank vessel by attempting to open the manlid. Always face away from the manlid opening when finally cracking and lifting the manlid to avoid inhalation of any potentially hazardous escaping fumes or unanticipated pressure release. Sudden release of steam pressure from steam tubes. Avoid standing in front of steam tube openings or quick release valves if the possibility of sudden pressure discharge exists, or when depressurising the steam heating system. Jamming of fingers in open valves during inspection. Do not place fingers into open valves as sudden closure could crush fingers. Falling from damaged ladder or walkway. Ensure repairs to damaged sections of ladder or walkway prior to treading on them if condition is unsafe to proceed. Ensure that there is no contamination on the ladder or walkway which may cause loss of grip. NOTE: ALL PERSONNEL HAVE A RESPONSIBILITY FOR THEIR OWN HEALTH AND SAFETY AND MUST TAKE CARE TO REDUCE ANY RISKS TO AN ABSOLUTE MINIMUM.

Section 2

DEFINITIONS AND CLEANING TERMINOLOGY

Section 2 Definitions And Cleaning Terminology Contents of Section

Definitions. (11) 1 Damage (11) 2 Age Related Deterioration (11) 3 Improper Repairs (11) 4 Full Refurbishment (12) 5 Partial Refurbishment (12) 6 Tank (13) 7 Hazardous Tank (13) 8 Statutory Test Date (13) 9 Detachable Parts (13) 10 Consequential Damage (13) 11 Cleaning Terminology (14) a) Evidence of last cargo (14) b) Material Safety Data Sheet (MSDS)(14) c) Certificate of Cleanliness (14) d) Cleaning Receipt (15) e) Entry Permit (or Safety Certificate) (15) f) Safety Document (16) g) Qualified Person (16) h) Specialist Cleaning Contractor (16) i) Transferable Stain (17) 12. GE SeaCo Surveyor (17) Appendix 2.1 Cleanliness Certificate (18) Appendix 2.2 Cleaning Receipt (19) Appendix 2.3 Entry Permit (20)

10

DEFINITIONS
The following definitions are used in this manual: 1 DAMAGE

Damage is one or more physical defects in a container caused by a single event or a series of events such as impact, abrasion contamination, cargo attack etc. which exceeds the acceptable limits as defined in Section 8 entitled Inspection Guidelines for Tank Containers of this handbook. This includes corrosion, pitting or gouges to the interior or exterior of the tank, shell, fittings or accessories. 2 AGE RELATED DETERIORATION

Age Related Deterioration (ARD) is one or more physical defects resulting inevitably from exposure of the container to conditions for which it was designed. It precludes the existence of any physical defect which is considered unacceptable in accordance with GE SeaCo's Inspection Guidelines, as defined in Section 8 of this handbook and which may have led to the deteriorated condition. 3 IMPROPER REPAIRS

An improper repair is any repair performed where any one of the following defects is present: The repair has not been performed in strict accordance with GE SeaCo guidelines.

11

The repair is of a quality or condition which could still be defined as damage according to GE SeaCo guidelines. The repair has an adverse affect on the original ISO dimensions of the container. The repair affects the structural integrity of the container. Use of incorrect materials. Sub standard preparation or painting. Poor quality welding or workmanship. Sub-standard cleaning or polishing of the tank or fittings.

FULL REFURBISHMENT

Full refurbishment is the process of removing all the paint coating and any corrosion from the tank frame by abrasive blasting followed by repainting and replacing the cladding and insulation. The insulation and cladding may be refurbished as part of a full refurbishment process. However, it is not essential for the cladding to be included in a full refurbishment process. 5 PARTIAL REFURBISHMENT

Partial refurbishment is the process of renovating areas of the tank to an extent less than that defined as Full Refurbishment.

12

TANK

Tank Container in its entirety. (Not just the tank shell)

UN PORTABLE TANK

Tank designed and approved for the carriage of dangerous goods (as defined by UN dangerous goods list). The GE SeaCo tank fleet includes UN Types T1 to T50 (IMO1, IMO2 and IMO5).

STATUTORY TEST DATE

The date when a periodic inspection and pressure test of the tank was carried out to comply with the regulations of the governmental approving agencies.

DETACHABLE PARTS are are the the

Detachable parts are components which not permanently attached to the tank and designed for easy detachment to facilitate loading, unloading or general operation of tank container. Examples of detachable parts are: Valves, gaskets and seals. Blank flanges and outlet caps. Bolts, nuts and washers. Syphon tubes. Electric plugs.

10

CONSEQUENTIAL DAMAGE

Any damage resulting from the lessee's failure to carry out a necessary repair.

13

11 a)

CLEANING TERMINOLOGY Evidence of Last Cargo

A written document from a qualified and authorised employee or representative of the lessee stating the proper shipping name of the last cargo, together with the U.N. reference number. Note: the brand name or proprietary name of the cargo is NOT the proper shipping name. b) Material Safety Data Sheet (MSDS)

A document issued by the manufacturer of the cargo detailing the cargo characteristics and safety precautions. c) Certificate of Cleanliness

A document issued by a qualified person stating: Tank container serial number Date, Time and Place of issue Name of Survey Company Name of Cleaning Company Last cargo and UN number Method of Cleaning Gas free entry permit A thorough visual examination has been carried out and the interior of the tank, valves and fittings are free of pitting, corrosion, contamination, particles of previous cargo and odour. - The tank is clean and dry. See Appendix 2.1 for an example of a Certificate of Cleanliness.

14

Cleaning Certificate Validity Date The Cleaning Certificate date of issue should be recent. An evaluation of the circumstances and the issue date should be undertaken to ensure that the tank has not been used since the time of issue. For example, allowance should be made for the transit time between the point of cleaning and the off-hire depot. Circumstances may vary and it is not possible to set a specific validity date. For certain cargo an entry permit / safety certificate will be necessary. d) Cleaning Receipt (wash ticket)

A document issued by the qualified person of a specialist cleaning contractor responsible for the tank cleaning stating that A thorough visual examination has been carried out and the interior of the tank, valves and fittings are free of contamination, particles of previous cargo and odour. See Appendix 2.2 for an example of a Cleaning Receipt. e) Entry Permit (or Safety Certificate)

A document issued by a qualified person of the repair depot, or surveyor, in order that personnel may safely carry out prescribed tasks. The document should state: Tank container serial number Date, Time and Place of issue Name of Survey Company Name of person issuing certificate Last Cargo and UN number MSDS reference Period of validity of the permit

15

Tests carried out (as applicable) oxygen reading (gas free) Purpose of tank entry All necessary precautions have been taken to make the tank safe for entering and carrying out prescribed work during the specified time.

See Appendix 2.3 for an example of an Entry Permit. The validity of the Entry Permit is strictly on a limited time basis; it must be current. Any delays in carrying out subsequent repair work may necessitate the issue of a further Entry Permit. f) Cleaning Document

Is a written declaration that the tank has been cleaned. Depending on the circumstances a cleaning document may be the: g) Cleanliness receipt Cleanliness certificate Entry permit (safety certificate) Qualified Person (e.g. surveyor, quality controller)

A person that is properly trained, competent and experienced and is authorised by the employer or governmental body as is appropriate, to undertake the task. h) Specialist Cleaning Contractor

A company of high-standing local reputation skilled in tank cleaning and licensed by appropriate governmental agencies and a member of applicable trade organisations.

16

i)

Transferable Stain

A stain or discoloration which can be removed from the metal surface of the tank shell or fittings by normal cleaning methods or by the use of a nylon abrasive Scotchbrite pad. 12 GE SeaCo Surveyor

Any GE SeaCo Engineer or any Engineer authorised by GE SeaCo to carry out Tank inspections or surveys.

17

APPENDIX 2.1

(GE SeaCo preferred format)

CLEANLINESS CERTIFICATE
ISSUED BY SURVEYOR
SURVEY COMPANY NAME AND ADDRESS:

TANK NO: PLACE OF ISSUE: CLEANING COMPANY: CLEANING PROCESS: LAST CARGO : UN NO. : DATE OF ISSUE / TIME : LOCATION:

EXTERIOR free from all cargo and contamination Exterior frame, tank & walkways YES Manlid and valve compartments YES Serial nos. and statutory markings YES Cargo labels removed YES INTERIOR Entry made into tank by surveyor Free from odour Free from all cargo and contamination Free from corrosion or pitting (if no, report detail below) Dry Valves Manlid seal Dip-pipe/ Syphon pipe Gas free Entry Permit issued REMARKS YES YES YES YES YES YES YES YES YES

VALVES/FITTINGS free from all cargo and contamination

A thorough visual examination has been carried out and the interior of the tank, valves and fittings are free of contamination, previous cargo and odour. The tank is clean and dry. NAME (PRINT) (being the qualified surveyor) SIGNED

18

APPENDIX 2.2 CLEANING RECEIPT (Wash Ticket)

ISSUED BY CLEANING COMPANY

CLEANING COMPANY NAME AND ADDRESS:

* * * * * * *
TANK NO: PLACE OF ISSUE: DATE OF ISSUE / TIME : CLEANING PROCESS: LAST CARGO : UN NO. : Gas free Entry Permit issued REMARKS YES

A thorough visual examination has been carried out and the interior of the tank, valves and fittings are free of contamination, previous cargo and odour. The tank is clean and dry. YES

NAME (PRINT)

SIGNED

(being the qualified surveyor)

The cleaning receipt as a minimum must contain the details marked *.

19

APPENDIX 2.3 ENTRY PERMIT

ISSUED BY DEPOT / SURVEYOR
ISSUED BY DEPOT - NAME AND ADDRESS:

ISSUED BY SURVEYOR - SURVEY COMPANY NAME AND ADDRESS:

TANK NO: PLACE OF ISSUE: CLEANING PROCESS: LAST CARGO : VALID FROM: TO: DATE DATE UN NO. : TIME TIME DATE OF ISSUE / TIME :

PURPOSE OF TANK ENTRY

TESTS OF CONTAMINATES AND ATMOSPHERE IN THE TANK TEST TYPE RESULT SATISFACTORY YES / NO

Safety equipment to be worn by person making entry into tank

A full examination of the hazard of the tank has been carried out and the appropriate safety tests completed with acceptable results. The tank is safe to enter. NAME (PRINT) (being the qualified surveyor) SIGNED

20

Section 3

COMPLETION OF TANK REPAIR ESTIMATE and COMPLETION OF INTERNAL SHELL CONDITION CHART

21

Section 3 -

Completion of Tank Repair Estimate and Completion of Internal Shell Condition Chart

Contents of Section
Completion OF Tank Repair Estimate. 1 Last Cargo 2 Test Date 3 Container Grading 4 Component 5 Damage Codes 6 Repair Codes 7 Damage/Dimensions - Remarks Internal Shell Condition Chart Appendix 3.1 - Interior Shell Chart (23) (23) (24) (24) (24) (25) (28) (28) (29) (31)

Appendix 3.2 - ISO Damage Location Code (32) Appendix 3.3 - ISO Component Codes Appendix 3.4 - Damage Code Description Appendix 3.5 - Repair Code Description Appendix 3.6 - Cost Allocation (37) (48) (52) (55)

22

COMPLETION OF TANKCONTAINER REPAIR ESTIMATE

The following instructions are for the benefit of depots that prepare manual Repair Estimates (RE). INTRODUCTION A Repair Estimate (RE) (which performs the function of off-hire damage report) must be completed by the depot for every tank entering the depot off lease. Freemove units moved in status A condition or new units ex manufacturer must be checked to ensure they have not suffered transit damage. If such units have transit damage then a Repair Estimate must be completed for that unit. For Tank Containers the Repair Estimate is a single page document. Listed below are descriptions of the entries that must be made in each section. * Depots should if possible report the Repair Estimate via EDI using their depot management system. (1) LAST CARGO

Enter the proper shipping name and UN number of the last cargo carried. Note :- abbreviations of the cargo name, brand name or proprietary name are not acceptable. The depot must be in receipt of a safety document stating the proper name of the last cargo, together with the UN reference number, prior to carrying out the inspection.

23

Additionally, information concerning last cargo will have already been advised in writing by the GE SeaCo Ops Centre prior to redelivery. It is vital, both for the safety of personnel and in order to convey last cargo data to the next user of the tank, that the last cargo data is accurate in every detail. If the information is missing or incomplete for any reason, the depot must contact the last lessee or GE SeaCo Customer Service Centre. Do not enter incorrect or incomplete information. (2) TEST DATE

This refers to the last 2/5 year statutory pressure test. Enter date of last test shown on the tank data plate. NOTE: Refer to Section 8, Sub-Section 12c to determine when the statutory testing must be performed. (3) CONTAINER GRADING

Unlike other equipment types there are no grading procedures applicable for tanks. (4) COMPONENT

If estimating with the ISO/Cedex coding system use the 3 digit alpha codes to denote the component. Enter the 3 digit alpha code shown on the Component List for any item which is damaged. Appendix 3.2 shows a list of Tank Components.

24

(5)

DAMAGE CODES

If estimating with the ISO/Cedex coding system use the 2 digit alpha codes to denote the damage. If estimating with the GE SeaCo coding system use the 2 digit numeric codes to denote the damage. Only note damages that exceed the acceptable limits, as defined in the Inspection Guidelines. See Appendix 3.3 for the full description of all damages Codes applicable to Tank Containers and a GE SeaCo to Cedex/ISO conversion. The damage code used to describe any particular damage will automatically allocate the costs of the repair. Therefore, the damage code system has important Operational as well as Technical implications. Notes on the use of Damage Codes: The Cedex/ISO alpha code is shown in brackets after the GE S numeric code.) (i) Damage Codes must always be used as a single code. A combination of two or more codes to describe damage to any individual item is not permitted. (ii) Improper Repairs (Codes 24 (IO) & 25 (IN)) There are two possible codes which can be used: 24 (IO) : Improper Repair - Old 25 (IN) : Improper Repair - New The Inspector must decide by reference to the On-Hire Date (see (4) above), whether the improper repair was carried out during the most recent lease (Code 25 (IN)), or before it (Code 24 (IO)).

25

(iii) Rust, or Damage caused by Rust (Code 17 (CO)) Code 17 (CO) must be used only in clearly defined circumstances as follows: (a) It must be used as a single code in any line of the Repair Estimate to describe damage caused by rust which is not a result of a Manufacturer's Defect or cargo attack or contamination. The nature of the damage will be sufficiently implied in the appropriate Repair Code(s) which are entered in the adjoining column (see (11) below). (b) It must be used in any line of the Repair Estimate to describe rust, as defined in (a) above, which requires rectification, by partial refurbishment. (c) In the case of full refurbishment of a tank container Damage code 17 (CO) can only be used for containers which are more than 5 years old or which are subject to a Refurbishment TTB. For containers less than 5 years old use Damage Code 62 (MN) - (New Manufacturing Defect) or 09 (CD) (Consequential Damage). (iv) Consequential Damage (Code 09 (CD)) Must be used for any damage resulting from the Lessee's failure to carry out a necessary repair. See Appendix 3.4 below for a full description of the use of Damage Code 09 (CD).

26

(v) Manufacturers' Defects (Codes 26 (ME) and 62(MN)) There are two possible codes which can be used: 26 (ME) : Manufacturers' Defect - existing 62 (MN) : Manufacturers' Defect - new (a) Code 26 (ME) must be used to describe damage caused by a manufacturers' defect which is subject to a Tank Technical Bulletin (TTB). The TTB identifies the series of containers affected and gives instructions on repair method and reporting procedure. (b) Code 62 (MN) must be entered to describe 'new' defects i.e. not yet identified by TTB. See Section 5 regarding the procedure for reporting both existing and new manufacturers' defects. (vi) Allocation of Costs The allocation of repair costs between the two principal account categories, Lessee and GE SeaCo , is determined by the Damage Code. Appendix 3.5 shows the Damage Codes which must be used in each of the circumstances defined. The first heading entitled ANY ITEM covers all components of the tank.

27

(6)

REPAIR CODES

Numeric (GE S) or alpha (Cedex/ISO) codes must be used to describe the type or method of repair required to rectify damage previously noted in the Damage Code column. See Appendix 3.4 for the full list of Repair Codes. (7) DAMAGE/DIMENSIONS - REMARKS

Specify the quantity and extent of repair requirement against each damaged component. The type of damage and repair method proposed should have already been noted in the Damage and Repair Codes. Therefore, no description of the damage and repair methods is required except in the case of damages or repair methods that cannot be adequately described by use of the coding system.

28

INTERNAL SHELL CONDITION CHART INTRODUCTION Whenever there is evidence of interior tank stains, shell pitting, rust, scoring, scratches, gouges or any other unsatisfactory internal condition, this must be documented on the Tank Container Interior Shell Chart. See Appendix 3.1 for an example of a form. When used to document unsatisfactory internal conditions, the Tank Container Interior Shell Chart becomes an addendum to the Tank RE and has the same distribution as the RE. In addition a copy of the chart must be faxed to the Engineering and Technical Services Dept., GE SeaCo London. (Fax 00 44 (0)207 939 5650 ). The Inspector enters the following information when completing the form: (1) STANDING DATA Tank Serial Number Enter tank prefix, serial number and check digit. Depot/Location Enter depot name, or preferably, GES depot code for depot location at which inspection is performed. Date Enter date of inspection. Report by Enter Inspector's name. Inspector Signature Enter Inspector's signature (at bottom of form) Tank Unit Type Enter GE SeaCo tank code Tank Material Enter barrel material, i.e. AISI Type 316 steel, or if lined tank, identify lining material.

29

Last Cargo Enter the proper name of the last cargo. UN Number Enter United Nations reference number. (2) SHELL CONDITION Complete the chart using the surface condition key provided. Show measurements for affected areas whenever feasible. Pitting Shape Indicate most prevalent shape of pits seen, when pits are present. Tick flat bottom, pin hole, crater or cavity as appropriate. Approximate Pitting Size Provide pit measurement size for depth and diameter (in mm), or if pit size varies, identify size as appropriate on the map. Area of Shell Affected For any condition indicate the percentage of area of the shell interior affected and remark whether the area affected follows any pattern e.g. ullage line, above/below cargo line etc. Discoloration Indicate the colour of any discoloration, for tanks showing any discoloration. Condition of Fittings Indicate if any of the condition(s) shown in the surface condition key are present on the syphon tube, manlid or valves; indicate the extent, location, and specific characteristics of the condition(s) found. Additional Remarks Use the space for additional comments as needed.

30

APPENDIX 3.1 - INTERIOR SHELL CHART INTERIOR SHELL CHART

TANK SERIAL NO DEPOT LOCATION DATE REPORT BY TANK UNIT TYPE LAST CARGO UN NUMBER TANK MATERIAL

SHELL CONDITION
PITTING SHAPE (INDICATE) STAINS SCRATCHES /GOUGES RUST PITTING FLAT BOTTOM (A) PIN HOLE (B) CRATER (C) CAVITY (D)

REMARKS
FRONT

MANHOLE AREA

MANHOLE AREA

REAR

SIGNATURE

31

APPENDIX 3.2 ISO DAMAGE LOCATION CODE SYSTEM Tank Components have their location identified by alpha codes (up to 4 characters in length). Appendix 3 below notes the components by section. The location code for each component is noted alongside the component. Only location codes noted alongside the component may be used. Damages will be located by panel(s). For the purpose of locating damages, the container is divided nominally into 4ft x 4ft (120 cm x 120 cm) segments. A tank frame location code consists of four characters depending upon the area containing the entire vertical and horizontal length of the damage. Location Code 1 1. The first character is selected to identify the appropriate face of the container as follows: R L T B F D U X I E right side left side roof or top bottom (floor) front end door / ladder & data plate end understructure whole container container interior container exterior

32

Location Code 2 2. The second character is selected to identify the appropriate part of the container face where the damage is contained. To do this the vertical faces of the container are divided into the top and bottom halves and upper and lower main components; the horizontal faces of the container (roof or top and floor or bottom and understructure) are divided into right and left halves when viewed from the door end. The relevant codes are: - upper (higher) component H - top half T - bottom (lower) component B G - lower component (ground) - left half L - right half R - both halves (i.e. top/bottom, X left/right, centre)

33

Location Code 3 3. The third and fourth characters are selected to identify the section of the container in which the damage is contained. a) On all containers the front and door ends are divided into the vertical section numbered, when viewed from the door end from left to right. 1 - for the left hand side corner post 2 - for the left half 3 - for the right half 4 - for the right hand side corner post b) On all containers the right and left sides, the roof, the floor and the understructure are divided into equal sections as follows: 5 sections - 1 through 5 c) When the damage covers one section only, the third character indicates the appropriate section number and the fourth character shall be filled in with N. d) When the damage covers several adjacent sections the first and last section shall be employed. e) When the damage covers several nonadjacent sections or if the damage repair details are not the same, then separate line items must be used. f) When the damage covers the entire length of the container face, the third and fourth characters are filled in with X.

34

Location Code 4 4. Numbering system for multiple components. a) In addition to the above described location code some components are more precisely identified in numerical order. b) The particular components of the door and front end such as the door locking bars or front (side) posts are numbered consecutively from left to right when viewed from the door end. c) The particular components contained in all other faces such as the roof bows, side posts, crossmembers are numbered consecutively from the door end. d) When the damage covers several faces of the inside of the container such as steam cleaning refurbishment or sealing of the panels the code IXXX shall be used. e) When the damage covers several faces of the outside of the container such as refurbishment, refixing or sealing panels removal of cargo stickers the code EXXX shall be used. f) When the damage covers several inside and outside faces of the container the code XXX shall be used.

35

The diagrams below illustrate the various faces and components and their appropriate codes:

H1

H2

H3

H4

T1

T2

T3

T4

B1

B2

B3

B4

G1

G2

G3

G4

Ladder / Data Plate Side View

H5 T5 B5

H4

H3 T3 B3

H2 T2 B2

H1 T1 B1

T4 B4

G5

G4

G3

G2

G1 ladder end

Left Side View 36

APPENDIX 3.3 ISO /CEDEX COMPONENT CODES ISO Code YLA YLG KWL YHA KWW YWA YWB YWC YWD YWF YWM YVC YVL YVH YVT YDC YDT YSP YBC YSB YSQ YLO ISO Loc. Code

ISO COMPONENT DESC

Tank Rails (Location = AANN) Ladder AANN Ladder handle AANN Ladder Landing (Tank) AANN Hand rail assembly AANN Deck or Walkway Ass. AANN Walkway AANN Walkway / Large AANN Walkway / Medium AANN Walkway / Small AANN Walkway fittings AANN Walkway mount Bracket AANN Tank Spill Box (Location = ABNN) Bott Valve Compartment ABNN Bott Vle Comptmt Cover ABNN Bott Vlve Comptmt Hinge ABNN Bot Vl Comprtmt TIR Tab ABNN Tank Drain Tube X-wire ABNN Tank draining tube ABNN Tank spill box ABNN Tank spill box cover ABNN Tank spill box hinge ABNN Tank Spill Box TIR Tab ABNN Spill Box Lock ABNN

37

ISO Code YAA YBM YCT MCA YPM YPP YRI YRT MST YUI YOM YFR MHT YDO MMI MCC MOL MIS MSD MFS MOC MPL MPD MPS MCE MPC YEA YEW YFU

ISO Loc. Code Tank Markings (Location = ADNN) AAR markings BAM marking CTC markings Caution marking Product marking LNNN, RNNN, Product plate holder ADNN RID/ADR markings RTMD markings Size marking UIC markings LNNN, RNNN, Operator marking ADNN FRA markings Height Marking DOT markings Weight marking DNNN, ADNN Country Code LNNN, RNNN, DNNN, FNNN, ADNN Owners logo ID set LNNN, RNNN, DNNN, Markings digit FNNN, TX1N, TX5N, Markings set ADNN Owners code Cargo plate ADNN Consolidated data plate ADNN CSC plate ADNN ACEP Marking ADNN Customs plate ADNN Earth connection marking ADNN Electrical wiring marking ADNN FLA plate ADNN ISO COMPONENT DESC

38

ISO Code MPO YTA YCC MPM MRU YWA YWB YWC YWD YWF YWM YTF YVP RLA

RLA

RLC YHR

RLG

ISO Loc. Code Owners plate ADNN Tank plate ADNN Calibration chart ADNN Manufacturers plate ADNN Markings other ADNN Tank Frame (Location = AFNN) Walkway AFNN Walkway / Replace Large AFNN Walkway / Replace Med AFNN Walkway / Replace Small AFNN Walkway fittings AFNN Walkway mount Bracket AFNN Tank Frame AFNN Vertical post AFNN LH1N to LH5N, LG1N to Side rail LG5N, RH1N to RH5N, RG1N to RG5N. LH12 to LH45, LG12 to LG45, RH12 to RH45, RG12 to RG45, LH13 to LH35, LG13 to LG35, RH13 Side rail to RH35, RG13 to RG35, LH14 to LH25, LG14 to LG25, RH14 to RH25, RG14 to RG25, LH15, LG15, RH15, Side Rail RG15, DG2N, DG3N, DG23, Consani DH2N, DH3N, DH23, FG2N, Horizontal FG3N, FG23, FH2N, FH3N, rail FH23. DB2N, DB3N, DT2N, DT3N, FB2N, FB3N, FT2N, FT3N, LB1N, LB5N, LT1N, LT5N, Rail gusset RB1N, RB5N, RT1N, RT5N, TL1N, TL5N, TR1N, TR5N, UL1N, UL5N, UR1N, UR5N. ISO COMPONENT DESC

39

ISO Code CFG CPA CPC CPV YDH YDG YDF YDR KDG YFF YTG YMP YFS YEC YLT KGD KEI YSA YSK TMT CBB CBR SMN SVS LIT BEA YEH

ISO Loc. Code DG1N, DG4N, DH1N, Corner fitting DH4N, FG1N, FG4N, FH1N, FH4N Corner post DB1N, DT1N, DX1N, Corn post - Consani DB4N, DT4N, DX4N, FB1N, FT1N, FX1N, Corner Post - CPV FB4N, FT4N, FX4N. Document holder AFNN Doct Holder Cap & Chain AFNN Doc. Holder Fixing Bolts AFNN Diagonal Brace Diagonal Bracing Gussets Frame Fasteners D*,L* ,R*, F*, T*, U*, AFNN Frame gusset/stiffener Frame strap mount pad Frame Strap Earth connection AFNN Load Transfer Area AFNN Rear Beam Guide (Tank) AFNN RR Sill Elect Instl-Tank AFNN Saddle AFNN Skirt D*, F*, AFNN Tank Heating (Location = AHNN) Cargo Thermostat AHNN Circuit breaker 2 Amp AHNN Circuit breaker 20 Amp AHNN Elec.On/Off Switch AHNN Elec.Volt.Switch AHNN Electric Lamp AHNN Electrical Control Box AHNN Electrical heating element AHNN ISO COMPONENT DESC

40

ISO Code YID WIR BEG YHC YET ECB EPL YSI YDV YSE YSV YSL YTM YTW YIG YIZ YIC YIN YIR PRV YCD YCS YCR YSN YTS YTM

ISO COMPONENT DESC Elect Instruction Decal Electrical Wiring Control Box Door Gasket Heating Element Cap Heating Terminal Block Mains Cable 460 volt Mains Plug 460 volt Steam inlet/outlet Steam trap Steam tubes Tank steam safety valve Tank steam line cap Tank thermometer Thermometer Receptacle

ISO Loc. Code AHNN AHNN AHNN AHNN AHNN AHNN AHNN AHNN AHNN AHNN AHNN AHNN AHNN AHNN

Tank Insulation (= AINN) Cladding - GRP Cladding -Stainl. Steel DX2N, DX3N, Cladding - Aluminum FX2N, FX3N, Insulation-foam LX1N to LX5N, RX1N to RX5N, Insulation Rockwool TX1N to TX5N, Cladding rivets UX1N to UX5N, Cladding support AINN Tank cladding strap Clad. Strap Rivets Sun Shield AINN Sun shield support AINN Tank thermometer AINN

41

ISO Code YAV YAP YAB YAS YAE YAT YAF YAU YAG YCA YAC YCG YAD YAW YXW YZW YYW YBF YGH YBD YBR YBP YBK YBO YBS YFC YFG YFO YFP

ISO Loc. Code Tank Loading/Unloading (= ALNN) Air Valve ALNN Airline Pipe ALNN Airline Valve - Ball ALNN Airline Vl - Ball Seating ALNN Airline Valve (1.5") Flange ALNN Airline Valve (1.5") Screw ALNN Airline Valve (2") Flanged ALNN Airline Valve (2") Screwed ALNN Airline Vlv / Tank Gsket ALNN Airline Valve Cap ALNN Airline Valve Cap (1 in) ALNN Airline Valve Cap Seal ALNN Airline Valve Cap(2") ALNN Weld-in Flange / Airlin Vl ALNN Weld-in Flange / 3 in Vlv ALNN Weld-in Flange / 2 in Vlv ALNN Weld-in Flange / 1in Vlv ALNN Blind flange ALNN Bolts ( Bott/Foot valve) ALNN Bott Outlt Ball Valve - Ball ALNN Btm Out Vlv - Ball Seat Ring ALNN Btm Out Btrfly Vl -Clos Plt ALNN Bott Outlt Buttrfly Valve ALNN Closure Plate Seat Ring Btm Out Bttrfly Vl - 'O' Rng ALNN Btm Out Bttrfly Vlv - Spindle ALNN Bottom Out Cap and chain ALNN Bottom Outlet Cap Seal ALNN Btm Out Foot Vlv - 'O' Ring ALNN Btm Out Foot Vl- Pres Plat ALNN ISO COMPONENT DESC

42

ISO Code YFK YFN YFD YFE YBB YBG YBV YFB YBL YFA YBT YBW YCO YEV YFJ YFV VVH YGD YGV YGE YGA YFJ YGB YGP YFH YLN YMA YMS YEG YTV

ISO COMPONENT DESC Btm Out Foot Vl- Seat Rng Bott Outlet Foot Vlv - Spring Bott Outlet Vlv / Blank Bolts Bott Out Vlv / Blank Gasket Bott Outlt Vlv / Foot Bolts Bott Outlt Vlv / Foot Gasket Bottom Outlet Valve Ass Bott Out Valve Blind Flange Bottom Outlet Valve Handle Bott Out Vlv Spigot Flange Bott Outlet Valve TIR Tab Weld-in Flang / Bot Outlt Vlv Coupling External valve assembly Foot Valve / Tank Gasket Foot valve assembly Foot Valve Handle Foot vlv Bolts(Ball- Foot vlv) Foot vlv Bolt(Foot vlv - Tnk) Foot vlv Bolts(Plat- Ball Vlv ) Foot valve gasket Foot Valve / Tank Gasket Foot vl Gaskt (Ball-Foot vlv) Foot vlv Gasket(Plat -Ball Vl) Foot Valve Operating Lever Level indicator Manometer /Pressure guage Manometer step guard Remote Trip - Cable Guard Sample valve assembly

ISO Loc. Code ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN

43

Spacer Top Ext. Valve Assembly Top Outlet Ball Valve - Ball Top Out Bal V -Bal Seat Rng Top Outlt B'fly Valve Seal Kit Top Outlt Blind Flange Bolts Top Outlt Blind Flang Gasket Top Out Butfly Vl - Cls. Plat Top Outlet Butterfly Valve YXR ALNN Closure Plate Seat Ring YXS Top Outlt Butfly Vl - Spindle ALNN YXO Top Outl Butrfly Vlv 'O' Ring ALNN YXD Top Outlt Prss Vlv - 'O' Ring ALNN YXM Top Outlt Prs. Vl - Pres. Plat ALNN YXN Top Out Pres Vl - Seat Ring ALNN YTP Top Outlet Valv / Blank Gskt ALNN YEJ Top Outlet Valve / Gasket ALNN YTE Top Outlet Valve / Tnk Bolts ALNN YTJ Top Outlet Valv / Tnk Gasket ALNN YTO Top Outlet Valve Assembly ALNN YTB Top Outlt Vlv Blind Flange ALNN YTN Top Outlet 10 inch Valve ALNN YWT Weld-in Flg / Top Outl 10 V ALNN YTH Top Outlt Vlv Opertg Handle ALNN YTI Top Outlet Valve TIR Tab ALNN YCU Custom Seal Tank ALNN YDI Diptube ALNN Tank Manhole (Location = AMNN) YMH Manhole assembly AMNN YMJ Manlid Handle AMNN YMF Manhole flange AMNN

ISO Code YPV YEU YXB YXC YGJ YTD YTC YXP

ISO COMPONENT DESC

ISO Loc. Code ALNN ALNN ALNN ALNN ALNN ALNN ALNN ALNN

44

ISO Code YMC YMI YMQ YMK YML YHD YMO YMB YMG YMU YMT YMD YMR YME YSH YXT YNT YLI YST YHE YSU YBA YBH YPA YPB YPR YPT YUF YFL

ISO Loc. Code Manhole cover (manlid) AMNN Manlid cover 6 sw. bolt AMNN Manlid cover 8 sw. bolts AMNN Manway Swingbolt Handnut AMNN Manway Swingbolt Lugs AMNN Manlid fasteners AMNN Manlid hinges AMNN Manlid Hinge Bracket AMNN Manlid gasket AMNN Manlid Gasket Seating AMNN Manlid TIR Tab AMNN Manhole dipstick AMNN Manhole dipstick holder AMNN Manway Dipstick Handle AMNN Tank Pressure Vessel (= APNN) Shell DX2N, DX3N, FX2N, FX3N, Shell Ext.r LX1N to LX5N, RX1N to RX5N, TX1N to TX5N, Shell Int.r UX1N to UX5N. Tank lining Stiffening LX1N to LX5N, RX1N to RX5N, ring TX1N to TX5N, UX1N to UX5N Head TX1N to TX5N Sump UX1N to UX5N Baffle APNN Baffle holder APNN Airline Valve Pad APNN Bottom Outlet Valve Pad APNN Pressure Relief Valve Pad APNN Top outlet valve pad APNN Vapour flange APNN Welded flange APNN ISO COMPONENT DESC

45

ISO Code

ISO Loc. Code Tank Safety Devices (= ASNN) YEM Emerg'ncy closr remote cntrl ASNN YFW Remote Trip - Cable ASNN YER Remt Trip - Cabl Guard Fixgs ASNN YEB Remote Trip Bracket ASNN YEL Remote Trip Operatg Handle ASNN YED Remote Trip Warning Decal ASNN YOH Tank overheat fusible link ASNN YEC Earth connection ASNN YCF Flame arrestor - cowl type ASNN YFM Flame arrestor - maxi Hi-flow ASNN YEX Gas tank /excess flow valve ASNN YIS Internal safety valve, gas tank ASNN YTR Tank safety relief valve ASNN YFT Relief valve flame trap ASNN YGF Saf. Vl. Hi-Flow PTFE seals ASNN YGV Saf. Valv.Hiflow Viton seals ASNN YSR Safety relief flange ASNN YPI Safety Rlf Vlv - Inr Pres. Sprg ASNN YPO Safty Rlief Vl - Out Pres Spg ASNN YVS Safety Relf Vlv - Vac. Sprg ASNN YTQ Safety Relief Valve Gasket ASNN YSW Weld-in Flg / Safety Relf Vl ASNN YRU Tank rupture disc ASNN YRD Tank rupture disc holders ASNN YRG Bursting disc gasket ASNN YRM Tank safty release manomtr ASNN ISO COMPONENT DESC

46

ISO Code YTT YTX YCI YGC YSC YTL YTK HWR YWN BUL ZZZ

ISO COMPONENT DESC Miscellaneous Tank (= AZNN) 2.5 Year Statutory Test 5 Years Statutory Test Inspt & Issue Clean Cert. Inspt & Issue Gas free Cert. Inspect / Issue Safety Cert. Leak Test (Barrel/Vlvs etc) Spark Test Hardware, screws, bolts Tank washing nozzles Tank Technical Bulletin No component code

ISO Loc. Code AZNN AZNN AZNN AZNN AZNN AZNN AZNN AZNN AZNN AZNN AZNN

PREFERRED ISO CODES Preferred ISO Damage and Repair Codes are denoted by *. Use these codes wherever possible whilst estimating. This enables an accurate translation between the GE SeaCo system and the Code used on the estimate. Codes not marked with * are still useable but will be translated to the (2 digit numeric code) GE SeaCo code. Ensure that this translation will still give the required allocation of costs for Damage codes and that repair codes indicate the correct repair method.

47

APPENDIX 3.4

Damage Code Description

Damage Code Description GES ISO Code Code GD* 01 SA 02 ST* 03 OC* BN 04 BO CB MF* IE* NO* WH* CT* CD* SD SR OO* BT BU BW CL DT* PD PI PO PU WA BR* CU HO* PH ISO Description Gouged Scratched Saturated/Wet Out of Calibration Burned Burned Out Tyre Unusable Motor Failure Inadequate Electrl Resistance Modifications Required Wet Hides Contaminated Consequential Damage Stretched Shrunk Overhead Obstruction Bent Bulged Bowed Compression Line Dented Pushed Down Pushed In Pushed Out Pushed Up Warped Broken/Split Cut Holed Pin Holes Costs Alloc A/c L L L L L L L L GES-PR GES-PR L L L L L L L L L L L L L L L L L L L L

05 06 07 08 09 10

11

12 13

48

Damage Code Description GES ISO Code Code 14 DH* MS* 15 NP 16 LO* CH 17 CO* 18 ML* CK* CW 19 GO GP MA 20 NI* 21 22 NT* NT SW OD TR* DB* DY Ol OR OS IO* IR NV IN* MM OU WM ME* ISO Description Dented and Holed Missing/Lost Not in Place Loose Corroded/Holed Corroded/Rusty Markings/Labels Cracked Cracked Weld GRP Surface Crack GRP Surface Crack Misaligned Not Within ISO Dimensions Foreign Fitting Not within TIR regs Switched Out of Date Test Required Debris/Dunnage Dirty Oil Saturated Odour Oil Stains Old Improper Repair Improper Repair Not as reqd by user New Improper Repair Mismatched Other Unacceptable Wrong Material Existing Manu Defect Costs Alloc A/c L L L L GES-PR GES-PR L L L L L L L L L L GES-PR GES-PR L L L L L GES- D GES- D GES- D L L L L GES- MD

23

24

25

26

49

Damage Code Description GES ISO Code Code BK 27 FZ* RO RT 28 WN WT* WV 29 PS* OI* 50 UI 51 IP* 52 IC* 53 OH* 54 FD* 55 FQ* 60 SH* 61 LF* MN* 62 PF 63 LK* FS* 64 TU WB 66 RD* BL 67 FP* RF DL* 68 SP TS 69 NL* 70 RA* ISO Description Blocked Frozen Rotted Rotten Worn Wear and Tear Weathered Pitted Surface Over-Inflated Tyre Over-inflated Imploded Improper Cleaniing Overheating Forklift Damage Food Quality Short/Open Circuit Low Fluid Level New Manu Defect Paint Failure Leak Flat Spots Uneven Tread Bald Tyre Rollover Damage Blowout Flat/puncture Run Flat Delaminated Separated Tyre Damage Nails Remove For Access Costs Alloc A/c L L GES-PR GES-PR GES-PR GES-PR GES-PR L L L L L L L GES-PR L L GESNew MD L L L L L L L L L L L L L

50

Damage Code Description GES ISO Code Code ZZ 94 RP * FL* 95 RR 97 99 PM* RC* ISO Description Special Damage Refurbishment Program Floor Refurbishment Program Floor Reburb Program Preventative Maintenance Conversion Required Costs Alloc A/c L GESCap GESCap GESCap GESPR GESCap

51

APPENDIX 3.5 Repair Code Description GES ISO Repair Repair Code Code 30
3X

ISO Description Straighten Re-align Straighten and Resecure Accumulated. straightening

(code not for use by depots)

GS* RA RS ///// IT* OP SF SN* BX CH EX IN MK RP* TP WD* GW* DR GT MV RD RM* WP* WW* SC* AB*

31 32

Insert Overlapping Section and Foam Section Fit by M&R Stock Recharge Fit Part EX Owners Stock Install Re mark Replace Top Up Weld Straighten and weld Drain Remove Glue and Tape Remove Markings Remove and Dispose Remove Sweep Water Wash Steam Clean Abrasive Clean & Paint

33

34 35

36

37 38 39 40

52

Repair Code Description GES ISO Repair Repair Code Code 41 PA PR* PS HN PI PV RU SI SP* TR ZZ SE* SR FT RE* FR* LC BU OX PT* RG* DO* PC* NA* SD* DU* AJ TC*

ISO Description Paint Partial Refurbishment Wire brush and paint Handling Required Pre-trip Inspection Repairs prior to refurb Rebrush Splice Special Repair Necessary Temporary Repair Special Repair Seal Reseal Refit Resecure Free and ease Lubricate Blank Out Overlay Patch Re-Glass / GRP Infill Deodorise Polish Clean No Action Necessary Sanding / Grind smooth Dry Out Adjust Test Calibrate

42

43 44 45

46 47 48 49 4X 50 51 52

53

Repair Code Description GES ISO Repair Repair Code Code 53 54 55 57 58 59 5X 61 66 67 77 80 81 88 89 95 97 99 AC DC* PP* CC* PX* IF* DF* TB* XW* BD MD* RT IP* RR* RW* AR* RX* RB* RC* VM* CO*

ISO Description Air Clean Dismantle and Clean Pickle/Passivate Chemical Clean Patch and Foam Full length insert Drain and Fill Tech Bulletin completed Grind and Weld Brand Modify Re Rate Photograph Remove and Refit Rewire Air Renew with Recon Part Rebuild Recondition/Refurbish Preventative Maintenance Conversion

54

APPENDIX 3.6

COST ALLOCATION Damg Cost Code Alloc.

Description / Remarks

ANY ITEM Repair of impact damage. Replacement of missing components. Replacement of life expired components, damage resulting from inevitable exposure to normal operating conditions. e.g. hardening / deterioration of seals, discoloration of decals, electrical component not functioning and no signs of damage etc. Unacceptable improper repairs done during the most recent lease or unacceptable non standard components fitted during the most recent lease. Unacceptable improper repairs done prior to the most recent lease or unacceptable nonstandard components fitted prior to the most recent lease. Consequential damage resulting from the Lessee's failure to carry out a necessary repair. i.e. saturation of the insulation resulting from a failure to repair the cladding. Various 15 (MS) L L

28 GESPR (WT)

25 (IN)

24 (IO)

GESD

09 (CD)

55

Description / Remarks

Damg Cost Code Alloc.

CLEANLINESS Cleanliness Certificate missing Normal cleaning of the tank interior and cargo spillage on exterior Normal cleaning of the tank exterior (road dirt, not cargo spillage) Additional cleaning of the tank due to improper cleaning before redelivery when the tank is returned with a valid cleaning document. This is when the tank is not sufficiently clean. i.e. recleaning of seals , valves or blemishes / traces of previous cargo Removal of non standard decals or marks. Residue of previous cargo that can only be removed by special procedures. These procedures can include structural repair, partial or full refurbishment, component replacement, or a special cleaning method. This code should not be used for seals and gaskets 18 (ML) 08 (CT) L L 15 (MS) 23 (DB) L L

28 GESPR (WT) 52 (IP) L

56

Description / Remarks

Damg Cost Code Alloc.

POLISHING Polishing of the tank - interior. e.g. .removal of cargo residues TESTING Periodic testing of the tank, e.g. 21/2 and 5 year tests Leak test due to repairs on the shell etc.(code leak test same as the damage) 22 GESPR (TR) Various L 23 (DB) L

REFURB AND POST REFURB REPAIRS Full refurbishment and additional work as a result of abrasive blasting on units subject to refurbishment other than specified below. Partial refurbishment and additional work as a result of abrasive blasting on units subject to refurbishment other than specified below. Where necessary due to cargo spillage/ contamination. 17 (CO) Cap Prog. (Full Refur b) GES PR (Part Refurb) L

17 (CO)

08 (CT)

57

Description / Remarks

Damg Cost Code Alloc.

WET/SATURATED INSULATION FOAM As a result of damage or failure of Lessee to carry out a repair or seal a damaged area. As a result of old improper repairs. As a result of deteriorating sealant on old repairs. As a result of an ARD. 02 (SW) 24 (IO) 28 (WT) 28 (WT) L

GES D GES PR GES PR

MANUFACTURING DEFECTS New manufacturing defects (i.e. a manufacturing defect not detailed by a current technical bulletin). this also includes post refurbishment repair work. Existing manufturing defect (detailed by a current TTB). 62 (MN) New Man. Defect

26 Existing (ME) Man. Defect

SEALANT Replacement of sealant which has failed as a result of ARD. Sealant required as a result of an impact damage or improper operation. 28 GESPR (WT) 16 (LO) L

58

Section 4

INSPECTION PROCEDURES

59

Section 4 - Inspection Procedures Contents of Section

Inspection Procedures Safe inspection procedures and practice.

(61)

A Post-Estimate (Estimate Verification) (62) B Joint-survey C Post-Repair D Combined Post-Repair & On-Hire (63) (64) (67)

E Supplementary Estimate Verification (67) F Lessee On-Hire Survey G Pre-delivery Inspection Appendix 4.1 - GQ Sticker Appendix 4.2 - Lessee Refuse Report (68) (70) (71) (72)

60

INSPECTION PROCEDURES
INTRODUCTION There are seven standard inspections that might be carried out while tank containers are in depot off-hire. GE SeaCo will confirm the inspections required. All inspections must be carried out by a GE SeaCo Surveyor except for pre-delivery Onhire Surveys which should be carried out by the depot's own quality control personnel. Inspection Types and their Objectives a) Post-Estimate (Estimate Verification) : Ensures the Repair Estimate conforms to GE SeaCo requirements. b) Joint-survey: Confirms with the customer's surveyor the allocation of repair costs. c) Post-Repair: Ensures the tank has been repaired correctly and is now a status A tank. d) Combined - Post-Repair and On-Hire: Ensures the tank has been repaired correctly and is now a status A tank. Additionally, provide for inspection as in f). e) Supplementary Estimate Verification: Ensure the additional work is necessary. f) Lessee On-Hire Survey Performed prior to lease, ensuring the tank complies with requirements. Include a written report and photos together with an updated cleaning certificate.

g) Pre-delivery Inspection Depot check prior to lease ensuring the tank complies with requirements.

61

A.

POST-ESTIMATE INSPECTION

Authenticating the Repair Estimate Must be performed promptly after depot has completed the Repair Estimate. Must be performed on ALL tanks: - returned from lease - freemoved in a damaged condition - freemoved units that sustain transit damage Is not required on tanks: - freemoved in a Status A condition. - freemoved from manufacturer Note: These tanks will require a visual exterior inspection for transit damage Action to be taken by the GES Surveyor: The GE SeaCo Surveyor must inspect the tank and ensure that the repair estimate is correct. the Repair Estimate must be completed in accordance with the instructions in Section 3. When the GE SeaCo Surveyor is satisfied that the Repair Estimate for the Tank is correct he must sign and date the estimate. Repair estimate checks must include: - A current, valid Certificate of Cleanliness. - The last cargo data is correctly entered. - Damage Codes noted correctly, ensuring the Cost Allocation is correct. - Only damage requiring repair is noted. - Correct method of repair is to be adopted. - Tank Technical Bulletin requirements met. - Repair costs (labour / materials) are correct. Using combination damages and low cost reconditioned components as opposed to new. - Function Testing of the electrical heating or other components has been carried out. - Statutory Test requirements complied with. - An internal mapping chart completed if a problem exists on the shell interior.

62

B. JOINT-SURVEYS (with customers surveyor) The joint survey is carried out after the postestimate inspection and must be performed using the GE SeaCo - Printed Estimate. The customer's surveyor must provide his own copy of the Repair Estimate. All customers surveyors must attend at same time. The two surveyors must agree the material costs and labour hours as allocated or an amended allocation. The estimate must clearly show all amendments. The estimate must be signed and dated by both the GE SeaCo and customer's surveyors. The GE SeaCo Surveyor may alter an item on the estimate by amending the damage and repair codes, description and the costs. After amendment the repair must still conform to Tank Inspection criteria or requirements. Cost amendments must be agreed with depot. If the customer's surveyor agrees costs, but refuses to sign the estimate, he should be warned that the survey is invalidated. The GE SeaCo Surveyor must write on the estimate Costs agreed but customer's surveyor unwilling to sign, and sign / date it himself. The depot must report the joint survey result and amended costs immediately to the local GE SeaCo Ops Centre. If agreement is not reached between the surveyors then the GE SeaCo Surveyor must immediately report to the GE SeaCo Ops Centre. Lessee Refused Costs Report Details of refused costs Colour photographs of the refused items Reasons why costs refused.. Send report to GE SeaCo Ops Centre. A copy of this form is shown at Appendix 4.2.

63

C.

POST-REPAIR INSPECTION

The post-repair process is used as a means for GE SeaCo to verify that the unit has been repaired in accordance with the estimate and meets all applicable criteria for a unit to be onhired. The Post-Repair Inspection procedures must be performed in all depots. Post-Repair Inspection The following procedures must be followed when performing a Post-Repair Inspection. At any time new or amended requirements or criteria may be introduced for specific tanks or tank containers in general, these must be applied in addition to the procedures below during the Post-Repair Inspection. C.1 Tank Container

The tank container being inspected must meet the specifications of a status A tank with regard to the inspection criteria as noted in the Tank Inspection Handbook, Technical Bulletins and other Technical requirements that may be in force. All repairs noted on the estimate and any damages that were not noted on the estimate must be fully repaired. Additionally an internal mapping chart will be done and photos taken of the various components noted below in C.3. C.2 Statutory Test Validity

The inspector must ensure that the tank Statutory Test validity is current; otherwise it must be updated as necessary. The requirements of the Statutory Test are noted in the Tank Inspection Handbook.

64

C.3

Photographs and On-Hire Report

Every tank container will require a number of photographs to be taken during the On-Hire Inspection. The photographs must clearly show - interior, sides, ends, top, underside and the top and bottom valve/ manlid compartment. An On-Hire report must be completed in an approved format together with an internal mapping chart. The Cleaning Certificate shall be renewed. The report and photographs must be made available on the Inspection Companys web site. C.4 Cleaning Certificate

Every tank container must enter the depot with a valid Cleaning document. At the conclusion of the On-Hire Inspection the inspector should revalidate the existing Cleaning Certificate or issue a new Certificate. C.5 GQ decal

When the On-Hire inspector is satisfied that the tank container meets all the necessary criteria he must issue a GQ sticker for that tank container. This should be placed into the document holder. Any previous GQ Sticker must be removed. Only when all the above steps have been satisfactorily completed, can the tank be noted a status A tank, the depot may then transmit the unit status to the Ops Centre.

65

NOTES Post-Repair Note 1 If the GE SeaCo Surveyor considers that the depot has omitted to repair items included on the estimate or has not repaired items correctly, then he must clearly mark these items for rework on the estimate. The cost of rework is for the depots account. Rework repairs must commence immediately and be completed in a timescale agreed with the GE SeaCo Surveyor. Following completion of rework, the unit must be re-inspected by the GE SeaCo Surveyor. Inspections will continue until the GE SeaCo Surveyor is satisfied that it meets the GE SeaCo requirements and quality standards. Note 2 If the GE SeaCo Surveyor considers that additional repairs are required, the depot must produce an Additional Estimate which must be approved by the GE SeaCo Surveyor. If the additional repairs are required as a result of damage caused to the unit whilst in the depot or repairs that should have been identified by the depot estimator at the time of offhire, the costs of rectification must be for the depot account. In this case no Additional Estimate is required.

66

D COMBINED POST-REPAIR & ON-HIRE This inspection combines the inspection requirements of C Post-Repair and

F Lessee On-Hire Survey

E.

SUPPLEMENTARY ESTIMATE VERIFICATION

The original estimate should indicate all damages requiring repair in addition to all TTBs and maintenance work required at the time of redelivery. Normally the only times a supplementary estimate for extra work will be required is when a tank container has been in depot for a period of time and the unit requires maintenance work or when there is a specific request from the Ops Centre to modify the tank or fittings. Any additional work required above what was noted on the original estimate will be to the depot account unless the damages were not required or were hidden damage. Any supplementary estimate should be submitted as per all normal procedures for authorisation. The Operations Centre may request a survey prior to work being authorised. The survey must ensure that the actual work is actually necessary and that it conforms to GE SeaCo requirements and to allocate the costs to either the depot or GE SeaCo account.

67

F. LESSEE ON-HIRE SURVEY If the customer requests an On-hire Survey then he should be encouraged to attend the Pre-delivery Inspection. In this case the procedures below must be followed in addition to the Pre-delivery Inspection procedures. If the customer does not require an On-hire Survey then the Pre-delivery Inspection carried out by the GE SeaCo Surveyor will serve to ensure that the tank container is in good working order prior to delivery to lease. Procedure This survey must be carried out with reference to the criteria detailed in Section 8, Inspection Guidelines for Tank Containers. If an item is beyond the acceptable limits as specified in Section 8 the survey must cease until the required repairs have been carried out. If the customer's surveyor accepts the unit as being in satisfactory operating condition but nevertheless refuses to sign the On-Hire Survey form, the GE SeaCo Representative must note in the REMARKS box the words acceptable to customer but customer's surveyor unwilling to sign. The GE SeaCo Representative must also add brief comments as to the reason for the refusal. The GE SeaCo Representative must immediately advise the local GE SeaCo OPs Centre. In this situation the unit can be delivered to the customer. The GE SeaCo Surveyor must immediately inform the local GE SeaCo Ops Centre: Customers surveyor rejects a unit as nonsatisfactory and in the opinion of the GE SeaCo Surveyor the unit is in satisfactory condition.

68

If the customer's surveyor requests further checks of the unit in addition to those detailed in this handbook.

If the customer's surveyor has his own On-Hire Survey report and requests the GE SeaCo Surveyor to sign it; the GE SeaCo Surveyor must not sign it unless all the following conditions are fulfilled: - All codes used are clearly defined on form. - All comments relating to the condition and operating serviceability of the unit are in accordance with those entered on the GE SeaCo form. - The customer's surveyor also signs the GE SeaCo form. - The customer's surveyor provides the GE SeaCo Representative with a copy of his own On-Hire Survey Report. The GE SeaCo form is always the official report confirming the agreement between GE SeaCo and the customer regarding the operating condition and serviceability of the unit. The customer's own On-Hire Survey Report does NOT take precedence over GE SeaCo's.

69

G. PRE-DELIVERY INSPECTION This inspection must be carried out immediately prior to release of the container. The depot prior to delivery to the customer must survey every tank being delivered for which GE SeaCo has given release authorisation. In the case of special tanks their individual requirements must be checked. The depot must ensure the tank: - Conforms to GE SeaCo booking requirements Any special requirements detailed in the booking advice have been completed - The tank container is of the correct type as detailed in the booking advice. - If it is more than 6 months since the On-Hire Inspection then the pre-delivery inspection must include a leak check. - Is fit for service according to GE SeaCo repair requirements and quality standards, including specific requirements for Special Tanks. - Must be fully operational according to the inspection criteria. If the tank is not repaired correctly, then it must reworked. - The cost of rework is for the depot's a/c. - Rework repairs must commence immediately and be completed in a timescale agreed with the GE SeaCo Operations Centre. - The unit must be re-inspected Electrical Or Reefer Tanks - depot must produce and retain the run test results. Once the Pre-Delivery Inspection has been satisfactorily completed then the lower section of the GQ sticker must be completed.

70

APPENDIX 4.1

GQ Stickers

All status A tank containers must have a completed GQ sticker as shown below, it should be placed in the document holder.

71

APPENDIX 4.2 Lessee Refused Costs Report The form shown below must be used to report the items refused at joint survey by the lessee surveyor. LESSEE REFUSED COSTS REPORT
Unit serial No.: Estimate No. On- Hire Date: LESSEE REPRESENTATIVE Co. Name: GE SeaCo REPRESENTATIVE Co. Name: LESSEE REFUSED LINES Line Hours No. Refused 1 2 3 Material Refused (Local Currency) Refused Grand Amount Total Surveyors Name: Surveyors Name: Date: Depot Code: City: Photos Taken Y/N

(If more, please continue on another form labelled page 2) LESSEE REASON FOR REFUSAL 1. 2. 3. GE SeaCo REP. REASON FOR LESSEE ALLOCATION 1. 2. 3. Attach a copy of the signed and surveyed estimate Signed (GE SeaCo) Signed (Lessee)

72

Section 5

IDENTIFICATION OF MANUFACTURERS' DEFECTS and PROCEDURE FOR REPORTING MANUFACTURERS' DEFECTS

73

Section 5 Identification of Manufacturers' Defects and Procedure for Reporting Manufacturers' Defects Contents of Section Identification of Manufacturers' Defects Procedure for Reporting Manufacturers' Defects Appendix 5.1 - Warranty Report for New Defects (75) (78) (81)

74

IDENTIFICATION OF MANUFACTURERS' DEFECTS The inspector should be aware of the need to monitor tank design and report potential manufacturing defects and unsatisfactory design in addition to actual manufacturing defects. Manufacturing defects must be identified and correctly reported on the Repair Estimate. Typical defects might be those involving: (1) FATIGUE CRACKS The most common fatigue cracks occur in the frame, tank support bearers and. All tanks should be checked for any signs of stress related failure of either welds or parent material. (2) WELD DEFECTS Possible defects are porosity, lack of fusion or misalignments to welds. Defects to the frame and bearer supports are often revealed by cracks in the welds. (3) DEFECTS AFFECTING ISO DIMENSIONS This type of defect is often identified after difficulties have been experienced in lifting a container by spreader. Over tolerance variances in ISO dimensions are more often as a result of damage or previous improper repair rather than defects in the original manufacture. However, it may be that a design defect to the end frame has caused misalignment.

75

Expansion of the insulation causing the insulation and cladding to exceed ISO tolerances is often the result of moisture ingress. It may be that defects to the security or water tightness of the cladding joints at manufacture are the root cause of the defect. (4) PAINT AND SURFACE PREPARATION Inspectors should be alert for any signs of corrosion that do not appear to be the result of normal deterioration or damage. Corrosion on a container of recent manufacture is a probable indication that the paint system is defective. The following are the most common types of paint related problems: (i) Paint Film Detachment The detachment of areas of the paint film in the absence of signs of sufficient impact or chemical contamination is a sign of coating adhesion failure. Such detachment may involve the top coat separating from the primer coat leaving the primer intact or alternatively the entire paint coating may detach leaving the bare steel substrate. This type of failure is the result of lack of intercoat adhesion, poor metal preparation, contamination of the substrate or brittle paint. (ii) Light Surface Corrosion Light surface corrosion appearing through the paint film may indicate insufficient paint film thickness. Where the corrosion appears on the exterior of the painted stainless steel shell this is often due to contamination by carbon steel particles at manufacture prior to painting.

76

(iii) Corrosion Blisters This is the most serious type of corrosion and can cause much damage to the steel unless promptly treated. Corrosion blisters form below the paint film and result in deep seated areas of rust and rapid decomposition of the steel. In the early stages the blisters appear as small bumps beneath the paint film which at this stage is still undamaged. As the steel starts to break down the size of the blisters increase until they break through the paint film. By this stage the corrosion process is well advanced and will have already significantly reduced the steel thickness. (iv) Electrolytic Corrosion Corrosion blisters described in (4)(iii) above can occur around data plates and other metal components attached to the container. This may be a result of using incompatible materials, usually the fasteners. Corrosion of aluminium fasteners and aluminium cladding might also be a result of electrolytic corrosion. (5) ELECTRICAL FAILURE Failure of items such as printed circuit boards, thermostat contacts and heating elements may be due to a manufacturer's design defect. The common cause of defects to the above items is moisture ingress through joints in cladding and control boxes as a result of defects at manufacture. However, previous improper repairs or failure to carry out repairs to damage on a timely basis must be investigated.

77

PROCEDURE FOR REPORTING MANUFACTURERS' DEFECTS Potential Manufacturing Defects and Unsatisfactory Design Depots and inspectors should report to the Engineering and Technical Services Dept. any defect or design defects that may be present on a tank: a) Design difficult to repair b) Design frequently damaged, or c) vulnerable to damage d) early deterioration, which although not a defect may become one. The procedure covers units of all equipment types. It applies both to 'new' Manufacturers' Defects and also 'existing' Manufacturers' Defects. For ease of reference the definition of New and Existing Manufacturers' Defects is: New Manufacturers' Defect Any failure discovered on a unit which is less than 5 years old and which cannot be attributed to age related deterioration (ARD), and which has not been identified in the Tank Fleet Survey by a Tank Technical Bulletin. The age of the unit must be determined by reference to the Tank Fleet Survey, not by reference to the data plate on the unit.

78

Existing Manufacturers' Defect Any failure which has been confirmed by GE SeaCo London to be a Manufacturers' Defect, and which has been either identified in the Tank Fleet Survey or covered by a Tank Technical Bulletin or other formal circular instruction issued by Engineering and Technical Services Dept. GE SeaCo London. PROCEDURE The procedure shown below is concerned with units returned to depot, either off-hire from lease or from a freemove. It does not cover the reporting or repair of in-service units on which manufacturers' defects have been discovered.
These procedures do not amend in any way the Fleet Condition Survey Report (FCSR) System, described in TTB No 30.

(1)

NEW MANUFACTURERS' DEFECTS (NEW MD)

When a New MD is identified, the depot must without delay send to the local GE SeaCo Ops Centre: A copy of the full printed Repair Estimate. Clear photographs illustrating the MD. Each photo must be marked with the unit serial number, date of photo, location, name of inspector, returning lessee. A completed inspection report, using the standard GESC Warranty Report form. No other reporting format should be used.

79

An example of the Warranty Report is shown as Appendix 1. NOTE: Up to five units may be entered on one form providing all the units are of the same manufacturer and display similar defects. (2) EXISTING MANUFACTURERS' DEFECTS (EXISTING MD)

For each unit on which an Existing MD is recorded, the following must be sent by the depot to the local GE SeaCo Ops Centre: A copy of the full printed Repair Estimate. Clear photos illustrating the MD (subject to exceptions listed below). Each photo must be marked with the same data as listed above for New MD's. In addition the TTB reference number must be shown.

NOTE: Photos are not required for all Existing MD's. TTB's will state whether or not photos are required. (In most cases photos will be required for an initial period and then the requirement will be withdrawn). Photographs should clearly indicate the potential or actual problem. On the rear of the photograph the following must be clearly noted: unit number date depot or location where photo taken TTB number if applicable No Warranty Report or other inspection report is required for Existing MD's unless otherwise stated on the Technical Bulletin

80

APPENDIX 5.1 Warranty Report for New Defects

Date : Manufacturer : Unit Type : Prefix Serial 1 2 3 4 5 Description of defect : Reported By : Inspected By : Depot Location : CD Date Of Delivery

Cause of defect :

Associated damage / Operating conditions :

Remedial action proposed :

Remedial cost EIR / RE Number 1. 1. 2. 2. 3. 3. 4. 4. 5. 5. Inspection / Investigation cost : Action : Action By :

Comments :

Copy to :

Photographs & Estimates must be attached. Send to email Fax ets@GE SeaCo.com + 44 20 7805 5920

81

82

Section 6

IDENTIFICATION OF FREQUENT MISUSE OF TANK CONTAINERS

83

Section 6 -

Identification of Frequent Misuse Of Tank Containers

Contents of Section Identification of Frequent Misuse of Tank Containers

(85)

84

IDENTIFICATION OF FREQUENT MISUSE OF TANK CONTAINERS A container may be deemed to have been misused if it has been subjected to any of the following conditions which have resulted in damage: Used in excess of the designed working pressure, or without ventilation (implosion). Handled by any means other than those specified in ISO document DIS 3874. Top side lift equipment (unladen tanks only) must be of the full frame type. Handling by forklift equipment is not permitted for tank containers. Transported a cargo that has caused damage by reaction between the cargo and the container. Transported by any vehicle or vessel which is not suitable for the carriage of containers. Used when the operating or assembly instructions have not been followed or when necessary components are not present or correctly fitted.

Complete the Repair Estimate as normal be immediately report misuse to Ops Centre.

85

Containers subjected to misuse may be identified if they display characteristics such as: Used in excess of designed working pressure. splits or distortion to steam tubes or shell. Implosion will result in the tank shell or other components bowing inwards. It is caused by failure to vent the tank after cleaning or whilst discharging.

Handled by any means other than specified in ISO document DIS 3874. Top side lift equipment (unladen tanks only) must be of the full frame type. Distortion of the top third of tank shell (chains too short) Distortion of the manway area due to lifting by use of a yoke in the manway opening End frames leaning in towards the interior of the unit (chains too short) Permanent twist in the container about a diagonal horizontal axis. (Lifted by chains from two diagonally opposite corner castings) Distortion to the underside shell, steam tubes or cladding (lifting by forks) Distortion to the side shell or cladding due to top side lifting without adequate support to the bottom side Distortion of the tank support bearers or movement of the tank within the frame due to the unit having been dropped.

86

Transported a cargo that has caused damage to the tank by reaction between the cargo and the container. General corrosion and staining Corrosion pitting Stress corrosion cracking Damage to paint coating or cladding caused by spillage or storage in a chemical environment Transported by any vehicle or vessel which is not suitable for the carriage of containers Abrasion or damage caused by the use of makeshift lashing

Used when the operating or assembly instructions have not been followed or when necessary components are not present or correctly fitted Implosion of the tank shell due to inadequate venting on discharge Implosion of the tank shell due to inadequate venting after hot washing Splits in the insulation and cladding due to operation of the tank in excess of the maximum cargo temperatures Damage resulting from disregarding assembly or security instructions Damaged valves and fittings due to improper tools (incorrect size wrench) Damage to manway lid and compartment due to failure to secure when transporting or stacking the tank Burnt electrical components due to incorrect voltage supply Damage to electrical components due to failure to secure control box doors.

87

88

Section 7

IMPROPER REPAIRS

89

Section 7 - Improper Repairs Contents of Section Improper Repairs (91)

90

IMPROPER REPAIRS

An improper repair is any repair performed where any one of the following defects is present: The repair has not been performed in strict accordance with GE SeaCo guidelines. The repair is of a quality or condition which could still be defined as damage according to GE SeaCo guidelines. The repair has an adverse affect on the original ISO dimensions of the tank container. The repair affects the structural integrity of the tank container. Use of incorrect materials. Sub-standard preparation or painting. Sub-standard cleaning of the tank or fittings. Poor quality welding or workmanship.

Not all improper repairs, as defined, need to be reworked. A distinction has to be drawn between repairs in progress and therefore controllable and repairs, already in existence on a container, which are being considered for rectification. All repairs carried out under the control of GE SeaCo must be performed in accordance with GE SeaCo repair procedures. Any repair

91

performed in an GE SeaCo depot which does not meet the GE SeaCo repair criteria should be rejected and the tank container considered still damaged and unavailable for lease until the repair has been made good in accordance with GE SeaCo repair procedures. Existing repairs which do not strictly meet GE SeaCo requirements can be considered acceptable if they meet the following requirements: The repair has been carried out in a competent manner using suitable materials and a good standard of workmanship. The repair has been in existence for a long time without any signs of failure. The materials used, although strictly not meeting GE SeaCo requirements, do not affect the structural integrity of the container. Repairs to non-critical areas e.g. cladding panels, which are not unsightly and are watertight and secure. Repairs which may not have been properly cleaned and painted and are showing signs of superficial corrosion. Abrasive polishing marks to the shell interior which do not significantly affect the cleanliness standard or structural integrity.

92

Section 8

INSPECTION GUIDELINES FOR TANK CONTAINERS ACCEPTABLE CONTAINER CONDITION (ACC)

93

Section 8 -

Inspection Guidelines for Tank Containers Safety

Contents of Section Introduction 1 2 3 4 5 6 7 8 9 Cleanliness Frame Walkway Assembly Paintwork Insulation and Cladding Manway Assembly Safety Valves Top Valves Shell (95) (96) (98) (105) (105) (106) (109) (112) (115) (121) (123) (128)

10 Bottom Valves 11 Heating 12 Miscellaneous a) Decals and Data Plates b) Document Holder c) Spill Box & Compartments 13 Test

(130) (132) (133) (134)

94

INTRODUCTION ACCEPTABLE AND NOT ACCEPTABLE DAMAGE The inspection guide which follows lists the component parts of a tank container and defines the Tank Acceptable Container Condition (ACC) criteria for: NOT ACCEPTABLE DAMAGE ACCEPTABLE DAMAGE

NOT ACCEPTABLE DAMAGE is damage that affects the safety, structural integrity, cargocarrying capacity or the ISO dimensional integrity of the tank container. THIS TYPE OF DAMAGE MUST BE REPAIRED ACCEPTABLE DAMAGE is minor damage which does not significantly affect any of the above conditions and therefore: NO REPAIR IS REQUIRED. DO NOT OPERATE VALVES /FITTINGS OR ENTER ANY TANK WHICH DOES NOT POSSESS A VALID CERTIFICATE OF CLEANLINESS AND VALID ENTRY CERTIFICATE. OBSERVE THE SAFE INSPECTION PROCEDURES AND PRACTICE AS DETAILED IN SECTION 1 OF THIS HANDBOOK AND ALL REGIONAL HEALTH AND SAFETY REQUIREMENTS.

95

1 1.a)

CLEANLINESS INTERIOR

Not Acceptable Damage/Condition Cargo, contamination or odour. Transferable stains. Corrosion, pitting, grinding or gouges. Missing or improper Cleanliness Certificate.

Acceptable Damage/Condition Discoloration or dull appearance. Abrasions or scratches more than 120 grit polish equivalent.

An Internal Shell Condition Chart must be completed for all interior shell defects. See Section 3 for details. NOTE: Tanks without a cleaning document must be considered unsafe and should not be inspected. A cleanliness document is required for all tanks prior to redelivery to depot for lease termination (off-hire). If the cleanliness document is not a Cleanliness Certificate the tank may be off-hired but a Cleanliness Certificate is required and should be added to the off-hire estimate and issued by a qualified person. Note: where stains are present, clean a test area at the time of estimate preparation to both determine the cost and ensure stains do not conceal corrosion pitting. If heavily stained tanks are redelivered, contact the Ops Centre immediately, to arrange re-cleaning prior to off-hire.

96

1.b)

EXTERIOR

Not Acceptable Damage/Condition Cargo contamination (cargo overspill). Oil, grease Contamination of the valve or manlid compartments. General dust and dirt (visible from 10 mtrs).

Acceptable Damage/Condition Minor dust and dirt (NOT visible from 10 metres).

NOTE: The valve and spill boxes must be clean. Check areas of overspill for damage to paint and cladding. Inspect drain tubes to ensure they are clear. 1.c) FOREIGN MARKINGS

Not Acceptable Damage/Condition Hazard warning labels or cargo labels. Non-standard labels or misleading marks. Remnants of labels. Insecure or unserviceable label holders. Customer logo

Acceptable Damage/Condition Serviceable label holders. Minor label glue residue.

NOTE: - Non-standard damaged label holders should not be replaced. Remove and make good the area. - If a customer logo has been fitted over or in place of the GE SeaCo logo, the customer logo should be removed. It is not necessary to renew the GE SeaCo logo, (See Section 12 of this chapter).

97

2 2.a)

FRAME CORNER POSTS

Not Acceptable Damage Cuts, holes, gouges or splits. Cracks in welds or parent metal. Improper repairs. Dents or distortions of a formed edge or face greater than 15 mm irrespective of length of deformation. Dents greater than 10 mm and less than 15 mm in depth in excess of two per post. Dents greater than 10 mm exceeding 300 mm in length. Twisted or bent beyond the ISO. Severe Corrosion.

Acceptable Damage Dents or distortions not exceeding 15 mm in depth except as qualified above.

NOTE: The GE SeaCo preferred corner post insert shape has angled ends. However existing inserts with square ends are acceptable if all other criteria are satisfied. A maximum of two structurally sound inserts are allowed to each post. An insert may include a maximum of two formed edges.

98

Not Acceptable

2.1i

2.1ii

2.1iii

2.1iv

2.1i a. insert through 3 formed edges. 2.1i b. less than 300 mm from casting. 2.1ii 2.1iii 2.1iv less than 150 mm between inserts. overlapping inserts. more than two inserts per post.

99

Acceptable Damage

2.2i

2.2ii

2.2iii

2.2iv

2.2i a min. distance between inserts is 150mm. 2.2i b minimum size insert is 150mm. 2.2.ii min. insert at post ends is 300 mm.

2.2iii a full-leng .0th insert is allowed. 2.2iv two inserts may have a common weld.

100

2.b

TOP /BOTTOM /SIDE /END /CRASH END RAILS (Incl. stacking supports and centre mounted crash rails)

Not Acceptable Damage Cuts, holes gouges or splits. Cracks in welds or parent metal. Improper repairs. Dents or distortions greater than 25 mm. Out of straight greater than 25 mm per 2m. Distortion reducing clearance between end bottom rail and valve to less than 5mm. Severe corrosion. Loose or missing fasteners. Out of ISO. Acceptable Damage Dents or distortions not exceeding 25mm. Dents in bottom face of bottom rails which do not affect any formed edge.

NOTE: If the damage cannot be straightened and it is necessary to repair either by an overplate, insert or a section then the following criteria will apply when assessing the type and extent of repair required. The minimum permissible length of an overplate, insert or section repair is 50mm; no maximum limit. No insert or section may finish within 50mm of the corner fitting weld or within 50mm of an existing vertical weld. If the planned insert or section will end within these areas then the repairs should be extended to the corner fitting or the existing weld. Over-plating is restricted to the top, bottom and inside faces of the rail where the formed edge is free of damage.

101

2.c)

ANCILLARY BRACING AND LOAD TRANSFER AREAS (LTA)

Not Acceptable Damage Cuts, holes gouges or splits. Cracks in welds or parent metal. Improper repairs. Dents and distortions greater than 25mm. Out of ISO. Severe corrosion. Loose or missing fasteners.

Acceptable Damage Dents and distortions less than 25mm.

102

2.d)

TANK BEARER SUPPORTS

Not Acceptable Damage Cuts, holes gouges or splits.. Cracks in welds or parent metal. Improper repairs. Dents or distortion greater than 20mm Dents of a formed edge greater than 13mm. Severe corrosion. Loose or missing fasteners. Out of ISO.

Acceptable Damage Dents not exceeding 13/20mm in depth as qualified above.

NOTE: In all cases of damage to tank bearer supports the tank shell must also be inspected for damage. In all cases of severe corrosion to the tank bearer supports the section of the bearer attached to the shell below the insulation must be checked for structural integrity. This may require local removal of insulation. The criteria for repair is detailed in 2(b) above except that over-plating is not permitted.

103

e)

ISO DIMENSIONS (FRAME)

Not Acceptable Damage i) Diagonals Any damage which affects the ISO required diagonal measurements between corner fitting apertures.

NOTE: The maximum permitted difference in distance between centres of apertures of diagonally opposite corner fittings are: 20' container: 13mm All end frames: 10mm ii) End Frame: Any dent, bend or bow beyond the limits of the ISO corner fittings. Side Frame Any dent, bend or bow beyond the limits of the ISO corner fittings. Top or Underside Any dent, bend or bow beyond the limits of the ISO corner fittings.

iii) -

iv) -

v) Cladding - Any dent, bend or bow beyond the limits of the ISO corner fittings.

104

WALKWAY AND LADDER ASSEMBLY

Not Acceptable Damage Insecure. Cuts, holes, dents affecting safety. Distortions greater than 50mm. Dents greater than 25mm. Out of ISO. Missing or loose fasteners.

Acceptable Damage Distortions not exceeding 50mm and less than 1 m long and not affecting safety. Dents and distortions not exceeding 25mm and not affecting safety. Cuts, holes, dents not affecting safety.

PAINTWORK

Not Acceptable Damage/Condition Severe Corrosion. Severely damaged by cargo contamination. Excessive scrapes and abrasions or delamination

Acceptable Damage Superficial Corrosion. Discoloration or faded paint colour. Minor scrapes and abrasions.

Note: where corrosion is equivalent to Euro standard Re4 or above, then remedial work is required.

105

5 5.a)

INSULATION AND CLADDING INSULATION

Not Acceptable Damage/Condition 5.b) Missing insulation material. Saturated by water or cargo. Improper Repairs. Deterioration by heat (burnt or baked). CLADDING

Not Acceptable Damage/Condition Cuts, holes, crack or splits penetrating the cladding thickness and allowing moisture ingress. Gaps at cladding joints allowing moisture ingress. Deterioration by heat (burnt or baked). Insecure cladding or retaining straps. Surface damage or staining of cladding due to cargo contamination. Severe corrosion. Improper Repairs. Distorted outwards beyond the limits of ISO. Dents greater than 25 mm. Hammered surface (golf ball surface)

Acceptable Damage/Condition Distortion not affecting security nor allowing moisture ingress except as stated above. Abrasion. Full belly GRP patch on existing aluminium cladding.

106

NOTE: In all cases of damage to the cladding, the tank shell, heating tubes and electrical components must also be checked. NOTE: The following criteria will apply when assessing the type and extent of repair required. Use overlay riveted patches as the standard repair. Minimum patch size Min. thickness - GRP Min. thick. - Aluminium alloy 150 x 150 mm. 2 mm 0.9 mm

The GRP or alloy colour must match original. Use overlay fibre glass tissue as the standard repair to formed GRP surfaces where riveted patches are impractical. Infill repairs should be used for holes less than 25mm to FRP /GRP. Extend patches to the retainer strap where the patch is within 30 cm of the strap. Care must be taken to ensure that drills or rivets do not damage the shell, steam tubes or electrical components beneath the cladding. Multiple patches on panel If when redelivered to depot the number of repairs or patches either present or required as part of the repairs, distracts significantly from the aesthetic appearance of the tank, then that section or panel must be replaced to achieve a more aesthetic appearance to the tank. A number of small patches (multiple patches in the same area) can be replaced with a larger single patch or renewed panel in order to achieve a more aesthetic result.

107

Cladding Patch Repair

Section through Patch

108

MANWAY ASSEMBLY

6.a) MANLID AND SWINGBOLT ASSEMBLIES Not Acceptable Damage/Condition Leaks. Missing customs sealing ring. Dents or distortion greater than 6mm or affecting proper sealing of the manlid. Missing, insecure, seized or nonoperational parts. Cracks. Pitting, corrosion or contamination. Improper repairs.

Acceptable Damage/Condition Non-standard hand nuts and pivot pins that are of similar design and material e.g. bronze or stainless steel. MANLID SEAL

6.b)

Not Acceptable Damage/Condition Cuts, cracks or distortion affecting sealing. Contamination Square butt joints and /or joints not properly sealed. Missing or insecure.

Acceptable Damage/Condition Minor surface degradation (perish), which does not contain contamination and does not affect sealing.

109

NOTE: Seals may be cleaned and re-used or be "turned" to use both sides. See paragraph 8 below for details of standard seals and gaskets.

MANLID

6 7 5 2 3

ITEM 1 2 3 4 5 6 7 8

DESCRIPTION Cover Seal ring Swingbolt assembly Neckring Hinge pin Self locking nut Washer Main hinge pin

110

6.c)

DIPSTICK AND CALIBRATION CHART Dipsticks are not fitted as standard.

Not Acceptable Damage/Condition Distortion or damage to the dipstick assembly preventing operation. Non stainless steel (AISI 316). Contamination or corrosion. Illegible or insecure.

NOTE: All tanks are fitted with a calibration chart.

If a dipstick is fitted at the time of offhire remove and place into GE SeaCo stock.

111

SAFETY VALVES

7.a)

PRESSURE ONLY OR PRESSURE AND VACUUM RELIEF VALVES

Not Acceptable Damage/Condition Contamination or corrosion Missing parts. Distortions affecting correct operation. Leaks or incorrect pressure setting. Missing or non-operational Customs sealing ring. Improper repairs, seals or gaskets. Missing or illegible statutory markings.

Acceptable Damage/Condition Missing TIR wires where customs ring is fitted. Missing dust plug. NOTE: Standard Seals Component Pressure < 2.65 bar Viton A > 2.65 bar PTFE Envelope Viton PTFE PTFE envelope Compressed fibre

Vacuum Gasket to Tank

Viton A PTFE envelope Compressed fibre

112

RELIEF VALVE
1 2 3 4

5 6

Item 1 2 3 4 5 6 7

Description Plastic plug Cap Setting locking grub screw Pressure spring pair Pressure Plate Vacuum spring pad Body

113

7.b) FLAME ARRESTOR GAUZE (where fitted) Not Acceptable Damage/Condition - Missing parts (only if originally fitted). - Damage or distortion affecting proper operation. - Contamination. NOTE: Flame arrestors are not fitted to pressure only valves or to non-hazardous tanks. c) RUPTURE DISC ASSEMBLIES Bursting Disc (where fitted) Not Acceptable Damage - Leaks or incorrect pressure rating. - Contamination or corrosion. - Damage (broken) or distortion affecting correct operation or sealing. - Improper parts, repairs, seals or gaskets. - Damaged pressure gauge (tell-tale gauge) affecting correct operation. NOTE: Rupture discs are not normally fitted as standard. Many tanks have rupture disc flange assemblies fitted. Where rupture discs and flange assemblies are in good condition they should remain on the tank. A damaged disc must be removed. Rupture discs and tell-tale gauge are fitted as standard to top outlet only tanks and special tanks e.g. TY0, TY1, TY2 TD0, TD1, TD2 TA0, TA1, TA2, TA4 TH1, TH2, TH4 TZ1T, TZ2T, TZ3T, TZ4T, TZ5T, TZ6T, TZ7T, TZ9T. TU2T, (and applicable TS2). NOTE: check with ETS Dept. regarding rupture disc requirements.

114

8 8.a)

TOP VALVES AIRLINE VALVE (VENT / VAPOUR RETURN VALVE)

Not Acceptable Damage Leaks. Contamination or corrosion. Damage or distortion affecting correct operation or sealing. Non-stainless steel (300 series) parts. Defective or non-stainless steel pressure gauge. Missing /broken cap, seal or chain. Improper repairs, seals or gaskets. Non-stainless steel cap, Missing or non-operational Customs sealing ring. Missing or non-operational parts.

NOTE: Gauges (manometer) are not fitted as standard but should not be removed (and aperture plugged) unless defective. Outlet screw fitting BSP standard for 6 bar tanks, 10 bar tanks are fitted with a bolted flange. Standard seals and gaskets, see below 8.b) TOP OUTLET VALVE (where fitted)

Not Acceptable Damage Leaks. Contamination. Damage or distortion affecting correct operation or sealing. Missing or non-operational parts. Damaged seals affecting proper sealing. Improper repairs, seals or gaskets. Non-stainless steel (300 series) parts. Non standard parts Missing Customs Sealing ring.

115

NOTE: Provision is made for top outlet valves but the top valve is not fitted, as standard, to tanks with bottom outlets. Where valve is fitted do not remove. The aperture (when a valve no fitted) must be fitted with a bolted blank plate. NOTE: top outlet only tanks must be fitted with syphon pipe. 8.c) Syphon Pipe (Dip Pipe)

Not Acceptable Damage Leaks. Contamination. Damage or distortion affecting correct operation or sealing. Missing or non-operational parts. Non-stainless steel Gap (at bottom less than 8mm, greater than 14mm)

116

TOP DISCHARGE
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DESCRIPTION Pull ring Handle lever Handle (LH) Spring Handle location pin M6 x 16 screw Retaining washer M8 x 20 capscrew (2) M8 spring washer (2) Stuffing clamp flange c\w TIR PTFE bush PTFE 'O' ring (2) Viton 'O' ring Spindle Spindle seat Body M8 nut (2) M8 spring washer (2) Closure plate PTFE lower spindle bush PTFE 'O' ring PTFE 'O' ring Lower spindle PTFE seal Seal clamp & Nitrile 'O' ring

117

TOP DISCHARGE

118

STANDARD SEALS AND GASKETS

Component Safety Valve Pressure'O' Ring Safety Valve Vacuum Safety Valve Gasket to Tank Airline Seals Manlid Seal a) Food Grade b) Chemical Grade c) bolted manlid Top Outlet Valve 'O' Ring Top Outlet Valve Seals Outlet Blank Plate Foot Valve 'O' Ring Bottom Outlet Valve Seals Valve to Tank Gaskets Outlet cap Seals Provisional aperature flange SWR PTFE Braid PTFE VITON A PTFE VITON PTFE PTFE env CF SWR SWR PTFE Braid PTFE env VITON PTFE PTFE env CF PTFE env VITON PTFE PTFE env CF PTFE < 2.65 bar VITON A PTFE env > 2.65 bar PTFE env VITON PTFE

PTFE env CF PTFE env CF PTFE PTFE

PTFE env CF PTFE env CF

Note

Env = envelope CF = compressed fibre

119

8.c)

TOP OUTLET BLANK

Not Acceptable Damage Leaks. Contamination or corrosion. Damage or distortion affecting correct operation or sealing. Missing or defective parts. Non stainless steel. Contamination.

Acceptable Damage/Condition Zinc plated galvanised steel bolts.

120

SHELL

Not Acceptable Damage Leaks. Cuts, cracks. Defects to welds or parent materials. Gouges, scratches or badly executed grinding (erratic pattern) deeper than 0.1mm. Excessive grinding or other metal depletion which reduces the shell thickness to less than the minimum. Grinding coarser than120 grit, and excessive grinding scars /uneven pattern. Corrosion or pitting. Stress corrosion. Improper repairs or non-standard fittings. Sharp indentations, creases or dents. Dents greater than 6mm to the top third of the tank shell. Dents greater than 10mm to the bottom two thirds of the tank shell. Hammer marks (golf ball surface)

Acceptable Damage/Condition Gradual distortions /slow dents measured over the length between exterior stiffeners less than 10mm in the bottom two thirds or less than 6mm in the top third of tank shell. Light abrasions or scratches to 120 grit polish equivalent or finer. Superficial etching with no resulting contamination traps. (Type A and where the thickness is not below the minimum.) Original manufacture rolling marks.

121

NOTE: Statutory re-testing is required after all welded repairs to the tank shell. Where pitting is recorded a thorough investigation must be carried out. An Internal Shell Condition Chart must be completed whenever defects requiring repair are detected. NOTE: All pitting must be reported by type, surface area affected and location on the chart detailed in Section 3. An inspection must be carried out to determine the depth of pitting and that visible pitting does not mask cavity pitting or stress corrosion. The investigation will involve localised polishing of the surface followed by visual examination with the aid of a magnifying glass and dye penetrant.

122

10

BOTTOM VALVES

a)

FOOT VALVE

Not Acceptable Damage Leaks. Contamination or corrosion Damage or distortion affecting correct operation or sealing. Improper repairs, seals or gaskets. Non-stainless steel parts. Missing or broken Customs sealing ring. NOTE: Standard seals and gaskets: See paragraph 8 above.

123

FOOT VALVE
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 DESCRIPTION Stuffing seal Viton seal Spindle PTFE seal Spindle bearing Seal energiser Bush seal PTFE seal Viton 'O' ring Spring boss gasket Spring assembly Clamp bolt (2) PTFE 'O' ring M10 x 15 bolt Spring washer (2) Handle assembly Poppet Fortyt 'O' ring Retaining pin Lift fork Countersunk screw (2) Retaining washer Clamp bolt (2) Spring washer (2) Stuffing clamp Retaining washer

124

b)

BOTTOM OUTLET VALVE

Not Acceptable Damage Leaks. Contamination or corrosion. Damage or distortion affecting correct operation or sealing. Improper repairs, seals or gaskets. Non-stainless steel parts. Missing or broken Customs sealing ring. NOTE: Standard seals and gaskets. See Section 8.2 The Bottom Outlet valve terminates in a 3 BSP screwed outlet. If any other fitting is present, contact GE SeaCo Operations Centre to determine if the standard part is to be reinstated.

125

BOTTOM OUTLET
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DESCRIPTION Split ring Operating lever Handle (LH) Handle location spring Handle location pin M6 countersunk screw Retaining washer M8 x 25 socket capscrew (2) M8 washer (2) Stuffing clamp PTFE bush PTFE 'O' ring Viton 'O' ring Spindle PTFE seal Body M8 spring washer (2) M8 nut (2) Closure plate PTFE lower spindle bush PTFE 'O' ring PTFE 'O' ring Lower spindle PTFE main seal Nitrile 'O' ring Clamp plate

126

c)

OUTLET BLANK (BLIND) FLANGE

Non Acceptable Damage Leaks. Contamination or corrosion. Non - stainless steel. Damage or corrosion affecting operation Missing Customs sealing ring. d) OUTLET CAP (screw cap)

Not Acceptable Damage Leaks Contamination or corrosion. Missing parts. Non - stainless steel. Damaged or improper screw threads. Missing or broken chain. Damage or corrosion affecting operation Note: standard screw thread is BSP. e) REMOTE TRIP

Not Acceptable Damage Damage rendering remote trip inoperable. Seized. Insecure. NOTE: Remote trips are fitted as standard to bottom outlet I>2.65 bar tanks. e) FUSIBLE LINK

Not Acceptable Damage Damage rendering fusible link inoperable. Insecure. NOTE: Fusible links are not fitted as standard to pre-2003 manufactured tanks. Where fitted, the link must remain in place.

127

11 a)

HEATING STEAM TUBE AND CAP

Not Acceptable Damage Leaks. Damaged screwed fittings. Missing dust caps. Missing or broken chain. Distortion to the tank shell, (due to overpressure or ice expansion). Acceptable Damage/Condition Tight dust caps which require to be removed by use of a normal wrench.

NOTE: In all cases of damage the steam tubes must be pressure tested. Defective steam traps should be removed; replacement is not required. Steam tube dust caps may be made from aluminium casting, stainless steel, gun metal or bronze. Replacement caps must be of the most economical material. b) THERMOMETER

Not Acceptable Damage Not operationing correctly. Broken face or dial. Missing or insecure. Improperly fitted.

Acceptable Damage/Condition Condensation which does not prevent legibility. Non standard type. NOTE: Thermometers are fitted as standard to ALL insulated tanks.

128

c)

ELECTRIC HEATING

Not Acceptable Damage Non operational. Damage or deterioration that may allow moisture ingress to control boxes or elements. Insecure components, cables or terminals. Corroded terminals or components. Improper repairs. Earth leakage less than 1 megohm. Missing parts. NOTE: All parts must be well maintained and fully operational. An electric heating function test is required at offhire (to prepare the EIR/RE) and at on-hire (pretrip inspection) for EVERY tank. A supply cable of approximately 6m length and a CE17 plug are fitted as standard.

129

12 a)

MISCELLANEOUS DECALS AND DATA PLATES

Not Acceptable Damage Insecure. Missing or illegible plates. Missing or illegible. Obscured or partly missing decals. Twisted or bent beyond limits of ISO. Acceptable Damage/Condition Scuffs and scratches. Dents or distortion except as qualified above. NOTE All Statutory markings (decals and plates) must be present,. The company logo (SeaCo, GE SeaCo) is not a statutory marking and as such is not required. If the logo is damaged or a repair is carried out over the logo then the logo should be either repaired in part as necessary, replaced completely or removed completely using the cheapest option.

130

TANK MARKINGS

Note: Some markings are only statutory it the tank is operated in a specific country or region, e.g. ADR,RID or BAM.

131

TANK MARKINGS

CONTINUED

b)

DOCUMENT HOLDER

Not Acceptable Damage Missing, defective or non-operational. Insecure. Water filled, or blocked drain-hole. Acceptable Damage/Condition Non standard type.

132

c)

SPILL BOX AND COMPARTMENTS

Not Acceptable Damage Non operational. Cargo residue or waste material. Twisted or bent beyond the ISO limits. Blocked drain tubes. Damaged. Insecure doors /lids where fasteners do not tightly secure the lid for transport. Missing Customs sealing ring and door fasteners. Acceptable Damage/Condition Dents, distortions or splits except as qualified above. EARTH (Ground) LUG

d)

Not Acceptable Damage Damaged, missing or painted.

133

13 a)

TEST Leak Test

Leak tests are required under the following circumstances: as part of the off-hire survey to check the tank shell, valves, safety valves and fittings. Following repair completion where the tank failed the off-hire leak test. Following repair completion where repairs could have affected the tank leak tightness.

This test does not replace the periodic leakage or hydrostatic test which is performed as part of the 2.5 or 5 year test procedures. b) Leak Test Procedure

The tank container should be pressurised with air as the pressurising medium. The Test Pressure should be a minimum pressure of 1bar and a maximum of 25% of the barrels Max. Allowable Working Pressure (MAWP). This test will be used to test the integrity of the tank barrel, valves and fittings. The pressurising medium should be introduced to the tank and raised (slowly and with due care) to the required pressure. When the required pressure is reached it must be held for 10 minutes without loss in pressure. The exterior flanges, valves and fittings must be checked to ensure that they are not leaking. Leaks can be identified by the continual formation of bubbles in the solution when it is introduced around the area being tested.

134

The bottom outlet valve should be tested using an apparatus similar to that shown below. Checking the foot valve and the outlet valve separately. Due to the nature of the air test medium it might seep pass the sealing faces where a liquid will not leak. Because of this it is permissible for the internal valve seals to seep a tiny amount in accordance with the criteria. Re-setting the foot valve (by opening and slamming) might be necessary to stop leaks. Not Acceptable Damage Leaks.

Acceptable Damage/Condition Manufacturers tolerance as noted below. Set-up to Leak Test Bottom Outlet Valve

Observe the water surface for bubbles Water level

135

Location /Component Shell Manlid, manlid seal Flanges, gaskets Exterior of all valves Relief valve O ring Airline butterfly valve ball seal Airline valve closure plate seal Butterfly valve closure plate seal Foot valve closure plate O ring Bottom valve assembly (both valves closed) Outlet cap or plate

Air Tolerance Zero Zero Zero Zero Zero Manufacturers tolerance Manufacturers tolerance Manufacturers tolerance Manufacturers tolerance Zero Zero

Liquid Tolerance Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero

c)

Statutory Test

Statutory re-testing is required after all welded repairs to the shell and as noted below. NOTE: Dangerous goods cargo may only be transported in a tank container that has a valid test certificate. Determination of which statutory test to carryout must be based on the criterion below: A 2.5 year leak test should be carried out when a 2.5 year test is due (i.e. 2.5 years after the last 5 year test) providing the test is up to 3 months or less before or after test expiry. Any tank that requires a 2.5 year test but the test is more than 3 months before or after expiry date should be given a 5 year test. Any tank that requires a 5 year test should be given a 5 year test Any tank arriving into depot with 6 months or less remaining test date should be tested as part of the estimate. Any unit in depot under repair where the test date has 6 months or less remaining should be tested at the time of repair. Any unit in depot where the unit is status A and the test becomes due within 6 months should be tested (except where instructions not to test the tank are issued in writing because the unit is not a demand unit) Any unit in depot to be delivered to a customer should have 6 months (or more) test remaining at the day of delivery (except when notified in writing to the contrary).

137

Test Intervals The table below gives the maximum interval between tests or examinations that is acceptable to the Competent Authorities.
Test or Examination Maximum interval between tests required by the regulations (years) IMO US DOT ADR CSC CFR 49 RID 5 5 5 2.5 2.5 -

5 year, hydraulic tank test at test pressure 2.5yr Leak test, pneumatic tank test at <MAWP Relief valve operation test Visual inspection interior Visual inspection waiver at 2.5 year subject to approval Visual inspection exterior Valves and fittings Visual inspection structure 2.5 year test date tolerance (days) 2.5 year test waiver (dedicated cargo, subject to approval) Tolerance overdue test (dedicated cargo, subject to approval)

2.5 2.5 yes

2.5 2.5 no

2.5 2.5 yes

2.5

2.5

2.5

2.5 <90 >90 yes

2.5 <180 >0 yes

2.5 <180 >0 yes

2.5 <180 >0 yes

180

Note Tests are required for tanks used to transport hazardous cargo, class 2, 3, 4, 5, 6, 7, 8, 9 The regulations do not require tests for non hazardous, non regulated cargo except CSC Tanks used for static storage within a plant should comply with local regulations transportation regulations do not necessarily apply

138

Section 9

CONVENTION FOR SAFE CONTAINERS (CSC)

139

Section 9 - Convention for Safe Containers Contents of Section Convention for Safe Containers. Fitting the CSC Plate Marking the container to indicate that it is operated under ACEP Appendix 9.1 - Data Plate Personal NOTES (141) (141) (142) (143) (144)

140

CONVENTION FOR SAFE CONTAINERS (CSC) 1 INTRODUCTION Every container must be checked on return to depot to ensure that it carries a valid data plate. This consolidated data plate should incorporate a CSC plate. If the data plate does not include a CSC plate then this must be fitted separately. In addition every container must be checked to ensure that it is marked to indicate that it is operated under GE SeaCo's Approved Continuous Examination Programme (ACEP). See paragraph 3 below for detailed instructions. 2 FITTING A CSC PLATE A new data plate must be fitted when: The original data plate has been lost. The container has never been fitted with a data plate.

Contact the GE SeaCo Operations Centre for the technical data, which must be stamped on the plate. All letters and numbers stamped on the plate must be a minimum of 5mm in height. An example of a typical data plate and the data required is illustrated below. The new CSC plate must be fixed in a readily visible place as close as possible to other existing approval plates e.g. Customs Type Approval plate etc. The majority of GE SeaCo tanks are fitted with a consolidated data plate, (as shown below). Use 4mm diameter zinc plated steel drive or selfsealing pull rivets to fix the plate to the tank frame.

141

3.

MARKING THE CONTAINER TO INDICATE THAT IT IS OPERATED UNDER ACEP

Every tank must be marked with the standard GE SeaCo ACEP approval number or a decal bearing the approval number ACEP-BDA-01 on or next to the CSC plate. This approval number is unique to GE SeaCo and if a decal bearing any other approval number is found on the container it must be removed. If the ACEP decal is missing, a decal bearing the above approval number must be fixed to the CSC plate in the section entitled Next Examination Due. Alternatively, if there is insufficient space, fit the decal immediately next to the CSC plate. The standard ACEP decal is illustrated below:

GE SeaCo Ops Centres/Depots must obtain supplies of the GE SeaCo ACEP decal from Engineering and Technical Services Dept., GE SeaCo London.

142

Appendix 9.1 - DATA PLATE

GE SEACO srl BRIDGETOWN BARBADOS
TANK SERIAL No. SCZU 870030-8 MANUFACTURE BY YORKSHIRE MARINE CONTAINERS ADDRESS BEVERLEY ENGLAND Date OF MANUFACTURE: MANUFACTURERS SERIAL NO: TANK DESIGN CODE: ASME. SECT. VIII DIV.1 TANK TYPE UN PORTABLE TANK T11: CAPACITIES/WEIGHTS/DIMENSIONS NOMINAL LIQUID CAPACITY 24,000 LITRES TOTAL MEASURE WATER CAPACITY AT 200C 24010 6343 US TitARE WEIGHT: 3650 kg 8046 lb MAXIMUM PAYLOAD: 26830 kg 59150 lb MAXIMUM GROSS WEIGHT: 30480 kg 67200 lb PRESSURES TANK WORKING PRESSURE: 4-0 bar 58 lb/in TANK TEST PRESSURE: 6-0 bar 87 lb/in STEAM TUBE WORKING PRESSURE: 4 bar 58 lb/in STEAM TUBE TEST PRESSURE 6 bar 87 lb/in TEMPERATURES AMBIENT TEMPERATURE RANGE: METALLURIGAL DESIGN TEMPERATURE: MAXIMUM PRODUCT TEMPERATURE TOTAL HEAT LEAKAGE FACTOR: FOR TEMPERATURE DIFFERENCE RANGE: MATERIALS TANK SHELL & ENDS BS1501:PART3: 316S33. TANK WELDS BS316S92. STEAM DUCTS 316S33 SHELL THICKNESS 4.8mm, ENDS 5.7mm EQUIVALENT MIN.THICKNESS MILD STEEL 6.35mm INSULATION POLYURETHANE FRAME BS 50C HIGH TENSILE STEEL CONNECTIONS BOTTOM OULET 3 inch AIRLINE 2 inch BSP TOP OUTLET 3 inch BSTD STEAM TUBES .75 inch BSP INSPECTING AUTHORITY LLOYDS REGISTER INDUSTRIAL SERVICES REGULATING AUTHORITIES AND APPROVAL/PERMIT Nos. Approval No. DOT (UK) IMO Type 1 DOT (US) IMOO1 ADR/RID CERT No 032567 CTC UIC APPROVAL RAILWAYS CODE COUNTRY OF APPROVAL UNITED KINGDOM TESTS FIRST AND SUBSEQUENT TEST DATES 4/92 5 YEAR TEST DATE WITNESS MARK

CSC SAFETY APPROVAL

APPROVAL REFERENCE GB-LR 7708-3/92 DATE MANUFACTURED APRIL 92 SCZU 870030-8 IDENTIFICATION NO. MAXIMUM GROSS WEIGHT 30,480 kg ALLOWABLE STACKING WEIGHT FOR 162,560 kg 1.8G 15240 kg RACKING TEST LOAD VALUE 2R LONGITUDINAL INERTIA &IR LATERAL INERTIA TESTED

67,200 lb 358,380 lb 33,600 lb

ACEP BDA-01

143

NOTES

144

NOTES

145

NOTES

146