Scribd
Upload
57 views3 pages

Single Angle Moment Capacity Calculation

1. This document summarizes the calculation of the moment capacity of a single angle member based on ANSI/AISC 360-05 provisions. 2. It considers yielding, lateral-torsional buckling, and leg local buckling limits and selects the minimum of these as the nominal flexural strength. 3. The calculations determine that the maximum factored moment of 3.81 kN-m is 56.5% of the reduced design flexural strength of 6.74 kN-m, indicating the design is adequate.

Uploaded by

Ciprian Stelea
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
57 views3 pages

Single Angle Moment Capacity Calculation

1. This document summarizes the calculation of the moment capacity of a single angle member based on ANSI/AISC 360-05 provisions. 2. It considers yielding, lateral-torsional buckling, and leg local buckling limits and selects the minimum of these as the nominal flexural strength. 3. The calculations determine that the maximum factored moment of 3.81 kN-m is 56.5% of the reduced design flexural strength of 6.74 kN-m, indicating the design is adequate.

Uploaded by

Ciprian Stelea
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

DWG.

ru
Projet:

Site:

Fait par: CpL Date: 2010-12-02 Verif. par: Classement

Dfinition

SINGLE ANGLE moment capacity calculation (Chapter F of ANSI/AISC 360-05)


M u := 3.81kN m Fy := 300MPa - resultant flexural moment due to factored loads := 0.9

Angle L102*102*7.9 b := 4in = 101.6 mm t := 5 16 in = 7.94 mm

y' := 1.11in = 28.19 mm Sc := 1.27in = 20.81 10 mm


3 3 3

- elastic section modulus from dimentions and properties table

1.Yelding
Sw := 1.27in
3

- elastic section modulus to the leg tip about the major principal axis

M y1 := Fy Sw = 6.24 kN m- yield moment about geometrical axis M n1 := 1.5M y1 = 9.37 kN m- nominal flexural strength

2.Lateral-Torsional Buckling Lateral-torsional buckling modification factor calculation:


M max := M u = 3.81 kN m M a := 2850N m M b := 3810N m M c := 2850N m Rm := 1.0 - absolute value of maximum moment in the unbraced segment - absolute value of moment at quarter point of the unbraced segment - absolute value of moment at centerline of the unbraced segment - absolute value of moment at three-quarter point of the unbraced segment - for singly symmetric members subjected to single curvature bending (for other see page 16.1-46 ANSI/AISC 360-05)

1/3

DWG.ru
Projet:

Site:

Fait par: CpL Date: 2010-12-02 Verif. par: Classement

Cb :=

12.5M max 12.5M max Rm if Rm < 1.5 = 1.14 2.5 Mmax + 3 Ma + 4 Mb + 3Mc 2.5 Mmax + 3 Ma + 4 Mb + 3Mc 12.5M max 1.5 if Rm > 1.5 2.5 Mmax + 3 Ma + 4 Mb + 3Mc

Elastic lateral-torsional buckling moment calculation:


Le := 3040mm ATTENTION: - laterally unbraced length of a member To choose - the bending is about one of the geometric axes of an equal-leg angle with lateral-torsional restraint at the point of maximum moment (NO or YES): a1 :=

k e :=

1 if a1 = 1 1.25 if a1 = 2

=1

k y :=

0.8 if a1 = 1 1 if a1 = 2

= 0.8

ATTENTION:

To choose - type of the stress at the toe (COMPRESSION or TESION):

a2 :=

2 0.66 E b 4 t C Le t b M e := k e 1 + 0.78 2 b2 Le 2 0.66 E b 4 t C Le t b + k e 1 + 0.78 2 b2 Le

1 if a2 = 3 1 if a2 = 4

M e = 45.27 kN m M y2 := M y1 k y = 4.99 kN m

2/3

DWG.ru
Projet:

Site:

Fait par: CpL Date: 2010-12-02 Verif. par: Classement

M n2 :=

0.17M e = 7.49 kN m 0.92 Me if Me My2 M y2 M 1.92 1.17 y2 M if M > M 1.92 1.17 My2 M 1.5M e y2 y2 M e y2 M e y2 M y2 (1.5My2) if 1.92 1.17 M My2 > 1.5My2 e

3.Leg Local Buckling


Width_Thickness_Ratio := "Compact" if b t 0.54 E Fy E Fy < b t < b t 0.91 E Fy = "Compact"

"Noncompact" if 0.54 E Fy

"Slender" if 0.91 k s := 1 if a2 = 3 b y' y' if a2 = 4


3

= 2.604

Sc3 := Sc k y k s = 2.65 in M n3 := min M n1 , M n2

if Width_Thickness_Ratio = "Compact"

Fy b if Width_Thickness_Ratio = "Noncompact" Fy Sc3 2.43 1.72 t E 0.71E

b t

Sc3 if Width_Thickness_Ratio = "Slender"

M n3 = 7.49 kN m M n := min M n1 , M n2 , M n3 M r := M n = 6.74 kN m FU := M max Mr OK "OK" if FU < 1 "PAS OK" otherwise


3/3

= 56.5 %

You might also like