Martin Engineering offers a choice of Brush Cleaners engineered to remove residual materials from conveyor belts. MARTIN(r) STRIP BRUSH CLEANER Uses 12 brush strips assembled on a series of hubs mounted on a shaft. The Strip brush design allows material to fall off the brush rather than settle into the bottom of the bristles.
Martin Engineering offers a choice of Brush Cleaners engineered to remove residual materials from conveyor belts. MARTIN(r) STRIP BRUSH CLEANER Uses 12 brush strips assembled on a series of hubs mounted on a shaft. The Strip brush design allows material to fall off the brush rather than settle into the bottom of the bristles.
Martin Engineering offers a choice of Brush Cleaners engineered to remove residual materials from conveyor belts. MARTIN(r) STRIP BRUSH CLEANER Uses 12 brush strips assembled on a series of hubs mounted on a shaft. The Strip brush design allows material to fall off the brush rather than settle into the bottom of the bristles.
Martin Engineering offers a choice of Brush Cleaners engineered to remove residual materials from conveyor belts. MARTIN(r) STRIP BRUSH CLEANER Uses 12 brush strips assembled on a series of hubs mounted on a shaft. The Strip brush design allows material to fall off the brush rather than settle into the bottom of the bristles.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 3
TECHNICAL DATA SHEET
Martin Brush Cleaner
Martin Engineering offers a choice of Brush Cleaners engineered to remove residual materials from conveyor belts. A. Martin Strip Brush Cleaner B. Martin Spriral Brush Cleaner B
BENEFITS Effective Cleaning Removes carryback fines and fibers with powered rotary action. Efficient Operation Efficient electric motor provides effective cleaning without excessive power consumption. Economical Solution Effective, yet low-cost answer to belt-borne residual material. Rugged Construction Durable angle iron and stainless steel components provide long service in tough conditions. High-Performance Cleaning Effective cleaning performance on difficult applications, including belts with ribs, cleats, grooves, or chevrons, or belts carrying sticky materials or stringy fibers.
MARTIN SPIRAL BRUSH CLEANER Bristles are wrapped in a continuous spiral around brush shaft to form effective cleaning system. Martin Spiral Brush Cleaner provides effective cleaning performance on dry fines clinging to belts with cleats, chevrons, or ribs. MARTIN STRIP BRUSH CLEANER Uses 12 brush strips assembled on a series of hubs mounted on a shaft to form a 10-inch diameter brush. Strip brush design allows material to fall off the brush rather than settle into the bottom of the bristles. Design allows simple replacement of individual brush strips. APPLICATION GUIDELINES Martin Brush Cleaners are designed for use in the secondary cleaning position. In other words, the recommended placement is at the point where the belt leaves the discharge pulley. (If that is not possible, the Martin Brush Cleaner may be mounted further along the conveyors return run where it can be supported by an idler or pulley.) Installation of a precleaner on the face of the discharge pulley below the material stream is always recommended.
Form No. L3431-06/12 Martin Engineering Company 1998, 2012
Metric belt widths are industry standards, not conversions.
DIM C 2.00 (51) DIM B DIM A 21.75 (552) MAX 16.75 (425) MIN 10.00 (254)
25.00 (635) MAX 20.00 (508) MIN
10.06 (256)
7.00 (178) Chute Wall
10.06 (256)
8.00 (203) 17.30 (439)
2.25 (57) 15.00 (381)
3.03 (77)
Form No. L3431-06/12 Martin Engineering Company 1998, 2012
TECHNICAL DATA SHEET
SPECIFICATIONS Electric Motor 230/460 Volt, 3 Phase, 60 Hertz Standard TEFC, 1750 Belts 18-42 in. (300-1200 mm): 1 hp motor Belts 48-96 in. (1200-2400 mm): 2 hp motor 5:1 Reduction1 & 2 hp on Martin Spiral and Strip Brush Cleaners Standard Polypropylene Brush: -20 to 180F (-29 to 82C) Optional bristles can be used in higher operating temperatures. Strip Brush Cleaner Bristle Diameter Bristle Material Bristle Length 0.040 (1 mm) Polypropylene 3 in. (76 mm) Spiral Brush Cleaner 0.038 (0.96 mm) Polypropylene 4 in. (102 mm)
Speed Reducer Service Temperature Standard Bristles
Other bristle diameters and brush materials (nylon and oil-tempered steel) are available. Consult your Martin Engineering representative for assistance in specifying non-standard products. SELECTION GUIDE Cleaner Available Belt Width When to Use Belts carrying dry, dusty, crumbled materials that readily release from bristles. Available in low-profile version and in wider constructions for challenging applications. Use for moist, clinging materials that cling to bristles and build up on brush shaft. Martin Standard Spiral 18-72 in. Brush Cleaner (450-1800 mm) Martin Strip Brush Cleaner 18-60 in. (450-1400 mm)
