Controller User Guide For Windows2000 - XP v3.2.1
Controller User Guide For Windows2000 - XP v3.2.1
User Guide
for Windows 2000 / XP
Version: 3.2.1
1.1 Controller
TouchKit is software, which contains drivers of the touch panel controllers for the
specified communication connectors, RS232, PS/2 and USB, and the other two
utilities:
• Configuration support
The calibration and draw test of touch panel are done by this utility. Besides,
users can add or remove for new RS-232 or PS/2 touch panel devices.
System will give you a warning, if users check the PS2AUX check box,
6. Choose the setup type that best suits your needs. There are two TouchKit
accessory utilities for choosing, Rotation Monitor Utility and Shutdown Utility.
Users can install the utility they want by checking the box. Then Press [Next >]
to continue installation.
8. Then type in the name of program folder for TouchKit or press [Next >] to
continue. There will be a default name for it.
During driver installation, the setup program will scan COM port for RS232
Touchkit controller. Once the controller was scanned, the setup program will
display a dialog as
Click Yes to add the controller on the specified COM port automatically.
10. Setup is complete. After TouchKit installation, the USB device will be found
automatically as soon as it was plugged into the computer. Then users can see
the new device on the application program window. And, the program will remove
the USB Device automatically as soon as it was unplugged.
TouchKit is software, which contains drivers of the touch panel controllers for the
specified communication connectors, RS232, PS/2 and USB, and the other two
utilities.
• Configuration support
The calibration and draw test of touch panel are done by this utility. Besides,
users can add or remove for new RS-232 or PS/2 touch panel devices.
System will give you a warning, if users check the PS2AUX check box,
6. Choose the setup type that best suits your needs. There are two TouchKit
accessory utilities for choosing, Rotation Monitor Utility and Shutdown Utility.
Users can install the utility they want by checking the box. Then Press [Next >]
to continue installation.
8. Then type in the name of program folder for TouchKit or press [Next >] to
continue. There will be a default name for it.
During driver installation, the setup program will scan COM port for RS232
Touchkit controller. Once the controller was scanned, the setup program will
display a dialog as
Click Yes to add the controller on the specified COM port automatically.
9. Windows is copying files to disk and the setup is complete. After finish the
installation, if PS/2 touch controller is installed, it needs to reboot the computer.
10. After Touchkit installation, Unplug and plug the USB touch controller into the
computer, Hardware wizard finds this hardware, Press [Next >],
After the driver is installed, Press [Finish >] to complete the USB device
installation.
General
General property page contains the functions of language selection, devices add/
remove, 4 points calibration, Draw test and Advanced.
General Function
Select the compatible language first or users may not see the normal display of
each button.
<Add> / <Remove>
Please check the touch panel devices (including its controller) are equipped well,
then click [Add] button to add all of those RS-232 and PS/2 devices to the Panel
List dialogue box.
The controller is displayed on the Panel List box. Users can get the information
of interface, type, firmware version and baud rate for each controller.
Select one device after added more than one device at the panel list window.
The one selected will activate the panel, and remember to do the calibration
before starting to use touch panel.
<4pts Cal>
Correct 4 point locations on screen with the panel. Press [4 pts Cal], screen
displays as follows.
In drawing test window, users can click [Clear] button to clear the window. Also,
users can click [Quit] or press mouse right button to quit from the drawing test.
In drawing test window, users can verify the panel linearity, calibration capability,
and drawing line quality.
<Advanced>
Touchkit provides more accuracy 25 points calibration for touch sensor. In
addition, Touchkit provide controller setting for capacitive touch sensor. If the
capacitive controller is selected, a capacitive setting property page appears on
the advanced sheet. In general case, it does not need to do 25 points calibration
other then bad linearity sensor.
If the selected controller is capacitive type, an extra property page for capacitive
setting adjustment shown as below:
Please select property size of capacitive screen first, and press [Restart]
Setting
There are three functional groups in Setting property page, and at the upper section
of the property page is sound option; at the middle section is Mouse Mode; and at
the lower section is Double Click Adjustment.
The Sound options provide users the click feedback while touching the panel.
Select preferred option first.
Sound options
<No Sound>
Users could choose to make no sound while using the touch panel.
<Touch Down>
The system will make a sound while touching the panel.
<Lift Up>
The system will not make any sound until finger leaves the touch panel.
<Frequency>
Sound frequency, drag the cursor from left to right is low to high.
<Duration>
Sound duration, drag the cursor from left to right is short to long.
Mouse Mode
<Mouse Button>
Click it to show / hide Touch Tray on the right bottom corner of the desktop.
The touch panel system starts with the computer booting, and a mouse icon
shows in the taskbar.
Users can choose show or hide Touch Tray from the mouse icon in the taskbar.
Just click the mouse icon to choose show or hide.
Touch Tray
Change right / left button by clicking the upper small rectangular box of Touch
Tray. Blue area expresses what button has been selected.
Shutdown utility
<Mouse Mode>
There are three kinds of mouse mode users could choose,
[Normal Mode]
It provides all the mouse functions, including the dragging function.
[Click on Touch]
Click action is executed as soon as users touch the panel.
[Click on Release]
Click action will not be executed until finger leaves the panel.
[Constant Touch]
Enable Constant Touch to force driver to stop reporting touch point when the
movement is small. Therefore, the user can see a stabilized cursor instead of a
chattering cursor when users touch the same point with unwanted noise.
If users want to cancel the function of TouchKit Hide Cursor, do the steps again
and choose the other scheme.
In some case, if it is difficult to touch items at the edges of the touch panel, users can
set adjustment to reach the edges of the screen image.
<Top>
If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position
of the top edge. If users set the Edge to <Larger>, TouchKit will extend the
horizontal position of the top edge.
<Bottom>
If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position
of the bottom edge. If users set the Edge to <Larger>, TouchKit will extend the
horizontal position of the bottom edge.
<Left>
If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of
the left edge. If users set the Edge to <Larger>, TouchKit will extend the
vertical position of the left edge.
<Right>
If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of
the right edge. If users set the Edge to <Larger>, TouchKit will extend the
vertical position of the right edge.
<Offset X Axis>
If users set the Offset X Axis to <Smaller>, cursor will be moved a pixel of X
Axis to left. If users set the Offset X Axis to <Larger>, cursor will be moved a
pixel of X Axis to right.
<Offset Y Axis>
If users set the Offset Y Axis to <Smaller>, cursor will be moved a pixel of Y
Axis to top. If users set the Offset Y Axis to <Larger>, cursor will be moved a
pixel of Y Axis to bottom.
Using +10% and -10% button to adjust the smaller or larger of edge. If users
press +10% button, the top, bottom, left and right edges will extend 10% of
orientation to touch screen, and cursor will be moved 10 pixel of X and Y Axis to
right and top. If users press -10% button, the top, bottom, left and right edges
will contract 10% of orientation to touch screen, and cursor will be moved 10
pixel of X and Y Axis to left and bottom.
If users want the value back to the default value, choose Default button.
<Multiple Monitors>
To configure the mapping relationship between the monitors and the touch
panels, select the monitor page as below.
Set the check box (Use Multiple Monitors) to enable multiple monitors mapping.
Uncheck this box will disable multiple-monitor configuration, and all of the touch
panel controllers will be mapped to the primary monitor. The gray shadow area
is the monitor mapped the selected controller/panel. The button [Mapping] is
used to find the mapping relationships between the monitors and touch panel
controllers. Press the [Mapping], the software will guide users to touch the
corresponding monitor to obtain the mapping relationship.
After finish monitor mapping, Press [Apply] to apply the mapping relation.
It shows the current resolution of display and users can set up the activate area
by inputting the value by yourself or use the default button [Upper Half], [Left
Half] or [Quarter]. The default value of panel resolution should be full screen as
Left: 0 , Right: 0, Top: 0 and Bottom: 0.
1. After activating the rotation of nVidia or ATI driver, there will be one blinking
symbol show as the following picture. Touch near the blinking symbol until stop
blinking, and the touch panel will rotate itself.
2. However, 180 degree rotation of touch panel can not be done in one step, users
need to rotate 90 degree twice.
2. There will be a pivot icon in the task bar. Users can click on it, and users can
choose four angles: 0 degree, 90 degree, 180 degree, 270 degree to rotate the
display.
3. After choosing the angle users want to rotate, there will be one blinking symbol
showing as the following picture. Touch this blinking symbol until stop blinking,
and the touch panel will rotate itself.
4. However 180 degree rotation of touch panel can not be done in one step, users
need to rotate 90 degree twice.
RotTray
RotTray icon
3. Clicking on RotTray, it will call Pivot to rotate the display and touch panel 90
degree at the same time. Clicking it again, it will rotate another 90 degree to 180
degree. Every click on RotTray, display will rotate clockwise. Recalibration and
one symbol adjustment won’t be necessary anymore.
4. However this version of RotTray is design for Pivot pro 6.05. If users want to use
older version of Pivot, like Pivot 5.1, users need to amend the value of windows
registry. The next step is an example for setting Pivot 5.1 on Win98.
7. Choosing the Hexadecimal Base, and replace the value data “4”(default) with
“FFFFFFFF”.
8. Here bellow are the value data for different version of Pivot:
1. TouchKit driver will not be unloaded until system re-boot. Press [Yes] to re-boot
immediately or [No] to re-boot later.