App 4

D Foundation Selection Tables
Tables 10.3, 10.1 and 10.2 from the main text are reproduced here as Tables D.1, D.2 and D.3 respectively for ease of reference in the foundation selection process.
Each of the tables gives details of suitable foundations to suit varying site and sub-soil conditions with guidance notes for factors to be considered during the selection process.
Table D.1 Foundation selection bearing strata strength and depth

Sub-soil conditions Condition 1 Suitable bearing strata within 1.5 m of ground surface Suitable foundation Strips Pads Rafts When loading on pads is relatively large and pad sizes tend to join up or the foundation needs to be balanced or connected then continuous beam foundations are appropriate. Strip foundations are usually considered the norm for these conditions but rafts can prove more economical in some cases. Condition 2 Suitable bearing strata at 1.25 m and greater below ground surface Condition 3 Suitable bearing strata at 1.5 m and greater below ground surface Strips 5 Pads 6 on improved ground using vibro or dynamic consolidation techniques Rafts 7 As Condition 2 plus the following Piles and ground beams Pier and ground beams Piles and raft As Condition 2 plus the following Buoyant rafts
Condition 4 Low bearing pressure for considerable depth Condition 5 Low bearing pressure near surface
As Condition 2 plus the following Rafts Ground improvement using preloading to support reinforced strips on rafts
Table D.2 Foundation selection sub-soil type

Sub-soil type Group 1 Rock; hard sound chalk; sand and gravel, sand and gravel with little clay content, dense silty sand Suitable foundation Factors to be considered
Strips/Pads/Rafts
(1) Minimum depth to formation for protection against frost heave 450 mm for frost susceptible soils. (2) Weathered rock must be assessed on inspection. (3) Beware of swallow-holes in chalk. (4) Keep base of strip or trench above groundwater level where possible. (5) Sand slopes may be eroded by surface water protect foundation by perimeter drainage. (6) Beware of running sand conditions.
Group 2 Uniform rm and stiff clays (a) where existing nearby vegetation is insignicant (b) where trees, hedges or shrubs exist close to the foundation position or are to be planted near the building at a later date
Strips/Pads/Rafts
(1) Trench ll likely to be economic in this category. (2) Minimum depth to underside of foundation 900 mm. (3) When strip foundations are cast in desiccated clay in dry weather, they must be loaded with the structure before heavy rains return. (1) Clay type and shrinkage potential, distance of trees from foundation and spread of roots dictate necessity or otherwise of piling. (2) Type and dimensions of pile depend on economic factors. (3) Where a suspended in situ concrete ground slab is used a void must be formed under it if laid in very dry weather over clay which is desiccated. (4) Where existing mature trees grow very close (e.g. within quarter of mature tree height) to the position in which piles will be installed. It might be prudent to design for sub-soil group 2(c). (5) Where trees have been or will be planted at a distance of at least one to two times the mature tree height from the foundation, a strip foundation may be suitable. (6) In marginal cases, i.e. with clay of low to medium shrinkage potential and in the perimeter zone of the tree root system, reinforced trench ll can be used. (1) Piles must be tied adequately into ground beams or the suspended reinforced concrete slab. An adequate length of pile must be provided to resist clay heave force, and the top section of the pile possibly sleeved to reduce friction and uplift. (2) Special pile design may be required for clay slopes greater than 1 in 10 where soil creep may occur and it is necessary to design for lateral thrust and cantilever effects. (3) In marginal cases, i.e. with clay of low to medium shrinkage potential and in the perimeter zone of the tree root system, reinforced trench ll can be used.
Concrete piles supporting reinforced ground beams and precast concrete oor units OR Concrete piles supporting a suspended reinforced in situ concrete slab OR Specially designed trench ll (possibly reinforced) in certain clay soils depending on position of foundation relative to trees OR Rafts
(c) Where trees and hedges are cut down from area of foundations shortly before construction
Reinforced concrete piles (in previous tree root zone) OR Strip foundations as in groups 2(a) and 2(b) (outside previous root zone) OR Rafts
Group 3 Soft clay, soft silty clay, soft sandy clay, soft silty sand
Wide strip footing if bearing capacity is sufcient and predicted settlement allowable OR Raft OR Piles to rmer strata below for small projects consider pier and beam foundations to rm strata
(1) Strip footings should be reinforced depending on thickness and projection beyond wall face. (2) Service entries to building should be exible.
Group 4 Peat
Concrete piles taken to rm strata below. For small projects, consider pad and beam foundations taken to rm strata below. Where no rm strata exist at a reasonable depth below ground level but there is a thick (34 m) hard surface crust of suitable bearing capacity, consider raft.
(1) Pile types used are bored cast in place with temporary casing; driven cast in place; and driven precast concrete. (2) Allow for peat consolidation drag on piles. (3) Where peat layer is at surface and shallow over rm strata, dig out and replace with compacted ll. Then use raft or reinforced wide-strip foundations depending on expected settlement. (4) Where raft is used, service entries should be exible. Special high-grade concrete and protection may be necessary in some aggressive peat soils.
Ground improvements of sub-soil Groups 3 and 4 by vibro treatments can often be achieved and can be an effective and economical solution when used in conjunction with raft or strip foundations
Appendices 321 Table D.3 Foundation selection varying site conditions

Site condition Filled site Suitable foundation Concrete piles taken to rm strata below. For small projects consider beam and pier foundations taken to rm strata below. If specially selected and well compacted ll has been used consider (1) Raft or (2) Reinforced wide-strip footings (3) Strip/pad/raft on ground improved using vibro or dynamic consolidation depending on ll type Factors to be considered (1) Allow for ll consolidation drag on piles, piers or deep trench ll taken down to rm strata below. (2) Proprietary deep vibro and dynamic compaction techniques can with advantage improve poor ll before construction of surface or shallow foundations. (3) If depth of poorly compacted and aggressive ll is small remove and replace with inert compacted ll, then use reinforced strip or raft foundations. (4) Deep trench ll taken down to a rm stratum may be economic if ground will stand with minimum support until concrete is placed. (5) Allow exible service entries to building. (6) Avoid building a unit partly on ll and partly on natural ground. (7) Take precautionary measures against (a) combustion on exposure to atmosphere, (b) possible toxic wastes, (c) production of methane gas. (1) Where a subsidence wave is expected, building should be carried on individual small rafts. Avoid long terrace blocks and L-shaped buildings. (2) In older mining areas, locate buildings to avoid old mining shafts and bell-pits. (3) In coal mining areas, consult The Coal Authority in all cases. (4) Avoid piled foundations. (1) Strip foundations act as retaining walls at steps. With clay creep downhill, design and reinforce for horizontal forces on foundations. Provide good drainage behind retaining wall steps. (2) Foundations are deeper than normal, so keep load-bearing walls to a minimum. Keep long direction of building parallel to contours. (3) In addition to local effects of slope on foundations, consider total ground movement of slopes including stability of cohesionless soils, slip and sliding of cohesive soils. (4) Make full examination of all sloping sites inclined more than 1 in 10. (5) The presence of water can increase instability of slope. (6) Special pile design may be required for clay soil slopes greater than 1 in 10 where soil creep may occur and it is necessary to design for lateral thrust and cantilever effects. (1) Notes relating to lled site apply. (2) Where possible, dig out badly placed or chemically aggressive ll and replace with inert compacted material. (3) Remove old walls in lled basements, or use piers or piles carrying ground beams to span such projections. (4) Deep trench ll down to rm strata at original basement level may be economic. (5) Trench ll depths may vary greatly as old basement depth varies. Some formwork may be required in loose ll areas. (6) Remove old timber in demolition material a source of dry rot infection. (1) In sand and gravel soil, keep foundation above groundwater level where possible. (2) Avoid forming steep cuttings in wet sand or silty soil. (3) Consider use of sub-surface shelter drains connected to surface water drains, and allow for resulting consolidation or loss of ground support. (4) Take precautions against lowering of groundwater level which may affect stability of existing structures.
Mining and other subsidence areas
Slip-plane raft
Sloping site
Foundations to suit normal factors and soil conditions, but designed for special effect of slope
Site containing old building foundations
Normal range of foundations. It is possible to use strips, piling, and pads but beware of varying depths of ll in old basements, causing differential settlement, and old walls projecting into ll over which slabs may break their backs.
Site with groundwater problems
Normal range of foundation types can be used. Consider piling through very loose saturated sand to denser stratum to provide support for raft or strip foundation at high level above groundwater. Consider use of proprietary vibroreplacement ground techniques to provide support for raft or strip foundation at high level above groundwater.

App 4

Uploaded by

Copyright:

Available Formats

App 4

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

App 4

Uploaded by

Copyright:

Available Formats

D Foundation Selection Tables

Table D.1 Foundation selection bearing strata strength and depth

Table D.2 Foundation selection sub-soil type

Appendices 321 Table D.3 Foundation selection varying site conditions

Mining and other subsidence areas

Site containing old building foundations

Site with groundwater problems

You might also like