Isa 75.17 Control Valve Aerodynamic Noise Prediction

AMERICAN NATIONAL STANDARD
ANSI/ISAS75.171989
Control Valve Aerodynamic Noise Prediction
Copyright ISA Provided by IHS under license with ISA No reproduction or networking permitted without license from IHS
--`,,,,,-`-`,,`,,`,`,,`---
Approved 19 June 1991
Not for Resale
ANSI/ISA-S75.17 Control Valve Aerodynamic Noise Prediction ISBN 1-55617-207-9
ISA 67 Alexander Drive P.O. Box 12277 Research Triangle Park, North Carolina 27709
Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
Copyright 1989 by the Instrument Society of America. All rights reserved. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the prior written permission of the publisher.
Preface
This preface is included for informational purposes and is not part of ISA-S75.17. This standard has been prepared as part of the service of ISA toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static, but should be subject to periodic review. Toward this end, the Society welcomes all comments and criticisms, and asks that they be addressed to the Secretary, Standards and Practices Board, ISA, 67 Alexander Drive, P.O. Box 12277, Research Triangle Park, NC 27709, Telephone (919) 549-8411, e-mail: [email protected]. The ISA Standards and Practices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standards. The Department is further aware of the benefits to USA users of ISA standards of incorporating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric units in all new and revised standards to the greatest extent possible. The Metric Practice Guide, which has been published by the Institute of Electrical and Electronics Engineers as ANSI/IEEE Std. 268-1982, and future revisions, will be the reference guide for definitions, symbols, abbreviations, and conversion factors. Certain metric units that are not a part of the SI system are in common accepted use. This standard uses bar as a pressure measurement that is convertible to kilopascals by multiplying by 100. It is the policy of ISA to encourage and welcome the participation of all concerned individuals and interests in the development of ISA standards. Participation in the ISA standards-making process by an individual in no way constitutes endorsement by the employers of the individual, of the ISA, or of any of the standards that ISA develops. The information contained in the preface, footnotes, and appendices is included for information only and is not a part of the standard. The following people served as members of ISA Committee SP75.17, which prepared this standard. NAME J. Arant, Chairman G. E. Barb R. Barnes H. Baumann B. A. Broxterman D. Cindrick L. R. Driskell J. T. Emery A. Fagerlund A. Gharabegian H. Illing J. Kahrs COMPANY E. I. du Pont de Nemours & Co. (Retired) Anchor/Darling Valtek, Incorporated H. D. Baumann Assoc., Ltd. Jordan Valve M. W. Kellogg Company Les Driskell, P.E. Honeywell, Inc. Fisher Controls International, Inc. Engineering Science DeZurik Valve Company Consultant
--`,,,,,-`-`,,`,,`,`,,`---
ANSI/ISA-S75.17-1989
Not for Resale
C. G. Langford, Vice Chairman H. L. Miller P. J. Nemergut K. W. Ng W. Rahmeyer J. N. Reed G. Reethof F. O. Seger A. K. Shea E. A. Skovgaard R. F. Tubbs J. Wang W. C. Weidman
E. I. du Pont de Nemours & Co. Control Components, Inc. E. I. du Pont de Nemours & Co. Naval Underwater Systems Ctr. Utah State University Masoneilan/Dresser Pennsylvania State University (Retired) Masoneilan/Dresser Copes-Vulcan, Inc. Leslie Controls, Inc. Copes-Vulcan, Inc. Exxon Research & Engineering Gilbert/Commonwealth, Inc.
The following people served as members of ISA committee SP75: NAME L. R. Zinck, Chairman J. B. Arant H. E. Backinger G. E. Barb R. W. Barnes/F. Cain* H. D. Baumann G. Borden, Jr. R. R. Brodin/F. Harthun* E. C. Brown E. J. Cooney L. R. Driskell J. T. Emery H. J. Fuller L. F. Griffith A. J. Hanssen B. A. Hart H. Illing R. L. Jeanes C. I. Koloboff J. D. Leist R. A. Louviere O. P. Lovett, Jr. P. C. Martin A. P. McCauley, Jr. H. L. Miller T. V. Molloy H. R. Nickerson J. Ozol R. A. Quance COMPANY Union Carbide Corp. Consultant J. F. Kraus & Company Anchor/Darling Valve Company Valtek Controls, Ltd. H. D. Baumann Assoc., Ltd. Stone and Webster Engineering Corp. Fisher Controls International, Inc. Dravo Engineers, Inc. Air Products & Chemicals, Inc. Consultant Honeywell, Inc. Consultant Consultant Retired M. W. Kellogg DeZurik Valve Company Texas Utilities Electric Chevron Corp. Dow Chemical USA Creole Engineering Consultant Hammel Dahl & Jamesbury Cont. Chagrin Valley Controls, Inc. Control Components, Inc. Pacific Gas & Electric Consultant Omaha Public Power Company Consultant
*One vote per company 4 ANSI/ISA-S75.17-1989

Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
This standard was approved for publication by the ISA Standards and Practices Board in 1989. NAME D. Bishop, Vice-President N. Conger C. Gross H. Hopkins R. Jones A. McCauley E. Nesvig R. Prescott D. Rapley R. Reimer J. Rennie W. Weidman J. Whetstone M. Widmeyer P. Bliss* W. Calder III* B. Christensen* L. Combs* R. Galley* T. Harrison* R. Jones* R. Keller* O. Lovett* E. Magison* R. Marvin* W. Miller* J. Mock* G. Platt* J. Williams* COMPANY Chevron U.S.A. Inc. Fisher Controls International, Inc. Eagle Technology Utility Products of Arizona Dow Chemical Company Chagrin Valley Controls, Inc. ERDCO Engineering Corp. Moore Products Company Rapley Engineering Service Allen-Bradley Company Factory Mutual Research Corporation Gilbert/Commonwealth, Inc. National Inst. of Standards & Technology Washington Public Power Supply Consultant The Foxboro Company Consultant Consultant Consultant Florida State University Philadelphia Electric Company Consultant Consultant Honeywell, Inc. Consultant Moore Products Company Bechtel Western Power Corporation Consultant Stearns Catalytic Corporation
*Director Emeritus ANSI/ISA-S75.17-1989

Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
W. Rahmeyer J. R. Reed G. Richards T. Rutter H. Schwartz K. G. Schoonover W. L. Scull H. R. Sonderegger R. U. Stanley R. E. Terhune R. F. Tubbs W. C. Weidman R. L. Widdows
Utah State University Masoneilan/Dresser Richards Industries, Inc. Fluid Controls Institute, Inc. Flexible Valve Corp. Con-Tek Everlasting Valve Co. Grinnell Corp. R D & E Retired Consultant Copes-Vulcan, Inc. Gilbert/Commonwealth, Inc. Cashco, Inc.
--`,,,,,-`-`,,`,,`,`,,`---
Not for Resale
Contents
--`,,,,,-`-`,,`,,`,`,,`---
1 Scope ................................................................................................................................. 9 2 Limitations ......................................................................................................................... 9 3 Nomenclature .................................................................................................................. 10 4 Pressures and pressure ratios ...................................................................................... 12 5 Regime definition ............................................................................................................ 13 6 Preliminary calculations ................................................................................................. 14 7 Regime I (subsonic flow) ................................................................................................ 15 8 Common equations for sonic and above ...................................................................... 16 9 Regime II .......................................................................................................................... 17 10 Regime III ....................................................................................................................... 17 11 Regime IV ....................................................................................................................... 18 12 Regime V ........................................................................................................................ 19 13 Noise Calculations ........................................................................................................ 19 14 Calculation flow chart ................................................................................................... 21
Appendix A References ..................................................................................... 22 Appendix B Example.......................................................................................... 23
Not for Resale
Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
1 Scope
This standard establishes a method to predict the noise generated in a control valve of standard design by the flow of compressible fluid and the resulting noise outside of the pipe and downstream of the valve. The transmission loss (TL) equations are based on a rigorous analysis of the interaction between the sound waves that exist in the pipe and the many coincidence frequencies in the pipe wall. Commercial pipe specifications allow a relatively wide tolerance in pipe wall thickness. This limits the value of the very complicated mathematical methods required for a rigorous analysis; calculations prove that a simplified expression is justified. The equations in this standard make use of the valve sizing factors defined in ANSI/ISA-S75.01 and ANSI/ISA-S75.02. This method was developed from the fundamental principles of acoustics, fluid mechanics, and mechanics.
2 Limitations
The method presented in this standard considers only single-phase dry gases and vapors; it is based on the perfect gas laws. Predictions are limited at this time to a downstream maximum velocity of Mach 0.3. Ideal straight metal pipe is assumed downstream. Uncertainties become greater as the fluid behaves less perfectly for extreme temperatures and for downstream pressures far different from atmospheric or if near the critical point. The method can be used with all conventional control valve styles including: globe, butterfly, cage type (but not with low-noise trim), and modified ball types. Specifically excluded are multistage proprietary low-noise valves and full-bore ball valves. This standard addresses only aerodynamic noise and does not consider any noise generated by mechanical vibrations, unstable flow patterns, and other unpredictable behavior. In the typical control valve, little noise travels through the wall of the control valve. The noise of interest is that which travels downstream of the valve inside the pipe and then escapes through the wall of the pipe to be measured typically at 1 meter (3 feet) downstream of the valve body and 1 meter (3 feet) away from the outside surface of the pipe. The majority of the test data available to validate the method is from air at moderate downstream pressures and temperatures; however, it is believed that the method is generally applicable for other gases and vapors and at higher pressures. The equations include terms that account for fluid density and ratios of specific heat.
--`,,,,,-`-`,,`,,`,`,,`---
Not for Resale
3 Nomenclature
Symbol
Description Speed of sound, downstream Valve flow coefficient Speed of sound at the vena contracta at subsonic flow conditions Speed of sound at the vena contracta at sonic flow conditions Diameter of jet Diameter, internal, pipe [2] Modifier, valve style Liquid pressure recovery factor Product of the liquid pressure recovery factor of a valve with attached fittings and the piping geometry factor Frequency, peak, generated inside pipe Piping geometry factor Frequency, coincidence Gravitational constant Ratio of specific heats Correction for pipe Mach number Sound pressure level, internal "A"-weighted sound level Mach number, freely expanded, in the jet Mach number Molecular weight Number of apparent, independent, flow passages in the valve trim Numerical constants Pressure, outside pipe, absolute Pressure, upstream, absolute Pressure, downstream, absolute Pressure, outlet at break point, absolute Pressure, outlet at critical flow conditions, absolute Pressure, outlet where region of constant acoustic efficiency begins, absolute Pressure, vena contracta, at subsonic flow conditions, absolute
Customary US Units ft/s gpm / ft/s ft/s ft ft dimensionless dimensionless dimensionless Hz dimensionless Hz 32.17 lbm-ft/lbf-s2 dimensionless dB dB dB (A) dimensionless dimensionless lbm/lbm-mole dimensionless [4] lbf/ft2 lbf/ft2 lbf/ft2 lbf/ft2 lbf/ft 2 lbf/ft2 lbf/ft2 psid
SI Units m/s [1] m/s m/s m m

--`,,,,,-`-`,,`,,`,`,,`---
c2 Cv cvc cvcc Dj Di Fd FL FLP

fp FP fo gc k Lg Lpi La Mj Mn
dimensionless dimensionless dimensionless Hz dimensionless Hz [3] dimensionless dB dB dB (A) dimensionless dimensionless kg/kg-mole dimensionless [4] Pa Pa Pa Pa Pa Pa Pa
Mw No N Pa P1
P2 P2B
P2C P2CE Pvc
10
Not for Resale
Symbol
Description Pressure, vena contracta, at critical flow conditions, absolute Pressure, standard, reference Radial distance centerline of pipe to observer [6] Universal Gas Constant Temperature, upstream, absolute Temperature, downstream, absolute Temperature, vena contracta, at subsonic flow conditions, absolute Temperature, vena contracta, at critical flow conditions, absolute Pipe wall thickness Transmission loss Transmission loss at coincidence frequency Correction for ratio of peak frequency and coincidence frequency Velocity, vena contracta, at subsonic flow conditions Velocity, vena contracta, at critical flow conditions Mass flow rate Stream power of mass flow Stream power of mass flow at sonic velocity Mass flow rate at sonic velocity Sound power Recovery correction factor Acoustical efficiency factor Mass density, upstream Mass density, downstream
Customary US Units lbf/ft2 2116 lbf/ft2 [5] ft 1545 ft-lbf / lbm-mol-R R R R R ft dB dB dB ft/s ft/s lbm/s ft-lbf/s ft-lbf/s lbm/s ft-lbf/s dimensionless dimensionless lbm/ft3 lbm/ft3
SI Units Pa 101325 Pa m 8314 J/ kgmole-K K K K K m dB dB dB m/s m/s kg/s W W kg/s W dimensionless dimensionless kg/m3
--`,,,,,-`-`,,`,,`,`,,`---
Pvcc Po r R T1 T2 Tvc Tvcc tp TL TLfo

TLfp
Uvc Uvcc w Wm Wms ws Wa
D K U1 U2
kg/m3
NOTES: 1) Units for valve flow coefficient Kv are m3/h. Substitute 1.157 Kv for Cv. The SI unit is Av = 2.40 x 10-5Cv. K v is not SI; its use 2) 3) 4) 5) 6) is discouraged. Usually, nominal diameter can be used with little loss in accuracy. gc is not required in the SI system; use a value = 1.00 in the equations. Values of numerical constants are given in Table 1. 2116 lbf/ft2 = 14.696 lbf/in2 The distance r is typically taken as 1 m (3 ft) plus the outer pipe radius.
Not for Resale
11
Table 1 Numerical constants, N

Constant Units Used in Equations
N NJ NL NT NF NP NS
1.5 X 10-2 4.6 X 10-3 5.7 X 1010 8.0 X 108 1.1 X 10-7 1.1 X 10-7 1.6 X 104 5.0 X 103 1.5 X 10-4 1.3 X 10-5 7.0 X 10-3 6.5 X 10-4
Di, Dj r, tp
ft m ft m ft m ft m ft m ft m
Wa
c2
P1,P2 Pa, Po
ft-lbf/s W
lbm/ft3 kg/m3
ft/s m/s lbf/ft2 Pa
lbf/ft2 Pa
4 Pressures and pressure ratios
The pressure in the vena contracta is developed from the definition of FL (see ANSI/ISA-S75.01):
( P1 P2 ) P vc = P 1 ----------------------2 FL
NOTE: When the valve has attached fittings, replace FL with FLP/FP. The pressure in the vena contracta at critical flow conditions is:
(4.1)
2 P vcc = P 1 ------------ k + 1
The downstream pressure where sonic flow begins is:
2
k ----------- k 1
(4.2)
P 2 C = P 1 FL ( P 1 P vcc )
NOTE: When the valve has attached fittings, replace FL with FLP/FP.
(4.3)
12
Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
The factor , the ratio between the external pressure ratio and the internal pressure ratio at critical pressure drop, is defined:
P1 --------- P 2 C P vcc = ---------------- = ---------P2 C P1 --------- P vcc
(4.4)
The downstream pressure at the break point between Regimes III and IV (see Section 5 for definitions of regimes) is:
P1 1 - P 2 B = ----- -- k
k ----------- k 1
(4.5)
The downstream pressure at the start of the region of "constant acoustic efficiency," where any further decrease in P2 will result in no increase in noise, is:
P1 P 2 CE = ---------22
(4.6)
5 Regime definition
--`,,,,,-`-`,,`,,`,`,,`---
A control valve controls flow by converting pressure energy into kinetic energy; some of this energy is transferred to the pipe wall as vibration, and a portion of this is radiated as noise. Most of the energy is converted to heat through viscous friction. At the vena contracta there is a pressure that may be even lower than the downstream pressure. The different regimes of noise generation are the result of differing sonic phenomena or reactions between the molecules in the gas and the sonic shock cells. In Regime I, flow is subsonic and the gas pressure is partially recovered or recompressed, thus the use of the factor FL. In Regime II, sonic flow exists, with interaction between shock cells and with turbulent choked flow mixing. Pressure recovery is less as the limit of Regime II is approached. In Regime III no isentropic pressure recovery takes place. In Regime IV the shock cell structure diminishes as a "Mach disk" is formed. In Regime V there is a constant acoustic efficiency. IF: IF: IF: IF: IF:
P1 > P2 P2C P2C > P2 Pvcc Pvcc > P2 P2B P2B > P2 P2CE P2CE > P2 0
THEN THEN THEN THEN THEN
REGIME = REGIME = REGIME = REGIME = REGIME =
I II III IV V
(5.1) (5.2) (5.3) (5.4) (5.5)
Not for Resale
13
6 Preliminary calculations
--`,,,,,-`-`,,`,,`,`,,`---
No is the number of apparent independent flow passages. Note that for cage-type trims this is usually the number of openings in the cage. Where a number of flow passages are in close proximity, as in some cage trims, the values require tests. The valve style modifier Fd (see Table 2) is:
Fd = No
( 1 2 )
(6.1)
For flow-to-open valves with contoured plugs at small openings, a special case occurs:
N S C v F L ( 1 2 ) Fd = 0.7 -------------------- 4 D2 i
Fd (maximum) = 0.7 for this equation.
NOTE: Use the required value of Cv, not the rated value of Cv. The jet diameter is:
(6.2)
Dj = NJ Fd ( Cv FL )
NOTE: Use the required value of Cv, not the rated value of Cv. The Mach number in a freely expanded jet is:
(1 2)
(6.3)
k ----------- P 1 k 1 2 - ---------1 M j = ---------- k 1 P 2
(1 2)
(6.4)
14
Not for Resale
7 Regime I (subsonic flow)
The temperature in the vena contracta is:
P vc Tvc = T1 -------- P1
The speed of sound (Mn = 1) is:
k 1 ---------- k
(7.1)
kRg c T vc ( 1 2 ) c vc = ---------------------- Mw
(7.2)
Table 2 Typical No and Fd factors

No
Flow to: Valve Type Single-Seat Globe Butterfly, Standard Angle Eccentric, Rotary Plug Ball Cage Double Seat, Parabolic Open 2.0 2.0 2.0 2.0 1.0 [1] 4.0 Close 1.0 2.0 1.0 1.0 1.0 [1] 4.0 0.5 0.5
Fd
Flow to: Open 0.7[2] 0.7 0.7 0.7 1.0 Close 1.0 0.7 1.0 1.0 1.0
NOTES: 1) Use the number of apparent independent openings in the cage at the actual valve stem position (refer to the manufacturer's catalog for the valve under consideration). 2) See Equation 6.2.
The gas velocity in the vena contracta is:

k 1 ---------- P vc k P 1 k - = 2 g c ----------- 1 ------------ k 1 P1 1 (1 2 )
U vc
(7.3)
--`,,,,,-`-`,,`,,`,`,,`---
Not for Resale
15
The stream power of the fluid in the vena contracta is:
Wm
By definition, the Mach number is:
w ( U vc ) = -------------------2 gc
(7.4)
U vc M n = -------c vc
The acoustic efficiency for Regime I is:
(7.5)
K I = ( 1 10 ) ( M n )
The sound power generated is:
3.6
(7.6)
Wa = K I W m FL
(7.7)
NOTE: When the valve has attached fittings, replace FL with FLP/FP . The peak frequency of the generated noise from the geometry is:
0.2 U vc f p = ----------------Dj
(7.8)
--`,,,,,-`-`,,`,,`,`,,`---
8 Common equations for sonic and above
The temperature in the vena contracta at sonic conditions is:
2 T1 T vcc = -----------k+1
The orificial velocity of sound is:
(8.1)
k R gc T vcc ( 1 2 ) c vcc = ------------------------ Mw
(8.2)
16
Not for Resale
The gas velocity in the vena contracta, at critical conditions, is:

k 1 ---------- P vcc k P 1 k = 2 g c ----------- 1 --------------- k 1 P1 1 (1 2)
U vcc
(8.3)
Stream power, at sonic (choked) velocity is:
W ms
wU vcc = --------------2gc
--`,,,,,-`-`,,`,,`,`,,`---
(8.4)
9 Regime II
The acoustic efficiency for Regime II is:
K II = ( 1 10 ) ( M j )
( 6.6 F L )
(9.1)
NOTE: When the valve has attached fittings, replace FL with FLP /FP .
P1 P2 W a = K II W ms ----------------------- P 1 P vcc
The peak frequency of the generated noise from the geometry is:
(9.2)
0.2 M j c vcc f p = -----------------------Dj
(9.3)
10 Regime III
The acoustic efficiency for Regime III is:
KIII = ( 1 10 ) ( M j )
( 6.6 F L )
(10.1)
NOTE: When the valve has attached fittings, replace FL with FLP/FP.
W a = h III W ms
(10.2)
Not for Resale
17
0.2 M j c vcc f p = -----------------------Dj
(10.3)
11 Regime IV
The acoustic efficiency for Regime IV is:
K IV
2 Mj ( 6.6 F L ) = ( 1 10 ) ------ ( 2 ) 2
(11.1)
NOTE: When the valve has attached fittings, replace FL with FLP/FP . The sound power generated is:
W a = KIV W ms
(11.2)
0.35 c vcc f p = ---------------------------------------------------(1 2) 2 1.25 D j ( M j 1 )
(11.3)
12 Regime V
k 1 ---------- k 2 M j = ----------- ( 22 ) 1 k1
(1 2)
(12.1)
--`,,,,,-`-`,,`,,`,`,,`---
18
Not for Resale
The acoustic efficiency for Regime V is:
KV
2 Mj ( 6.6 F L ) = ( 1 10 ) ------ ( 2 ) 2
(12.2)
NOTE: When the valve has attached fittings, replace FL with FLP/FP . The sound power generated is:
W a = K V W ms
(12.3)
0.35 c vcc f p = -------------------------------------------------(1 2) 2 1.25 D j ( M j 1 )
(12.4)
13 Noise calculations
The downstream temperature T2 may be determined using thermodynamic isenthalpic relationships, provided that the necessary fluid properties are known. However, if the fluid properties are not known, T2 may be taken as approximately equal to T1. Downstream density is:
2 7 2 = 71 ------ P 1
(13.1)
The speed of sound under downstream conditions is:
kRg c T2 ( 1 2 ) c 2 = ------------------- Mw
N L W a 7 2 c 2 ----------------------------- 2 10 Di
(13.2)
This is calculated in order to calculate the Mach number. Internal sound pressure level is:
L pi = 10 log
(13.3)
NOTE: The reference pressure used in (13.3) is 2 x 10-4 bar equivalent to (2 x 10-5 Pa). The transmission loss at the coincidence frequency at the distance r is:
3
TLfo = 10 log
10
P Di 1 - a N T ------ --------------------- ----- P o rt 2 P p 2 ----- + 1 P o
(13.4)
NOTE: The fraction Pa /Po is a correction for local barometric pressure.
--`,,,,,-`-`,,`,,`,`,,`---
Not for Resale
19
The pipe coincidence frequency is:
NF f o = -----------4 D i
(13.5)
Sound travels through the pipe wall depending on the relationship between the peak generated frequency and the pipe coincidence frequency: If fp fo: If fp > fo and fp 4fo: then T Lfp = 20 log then T Lfp = 13 log then T Lfp = 20 log
f o --10 f p f p --10 f o
(13.6)
(13.7)
If fp > 4fo: (13.8) Transmission loss is:
fp ------- + 7.8 10 4 f o
TL = T Lfo TLfp
(13.9)
The transmission loss correction for downstream fluid velocity is approximately (limited to 0.3 Mach, maximum):
L g = 16 log
10
1 ----------------------------------------- N p P 1 C v F L 1 --------------------------- D2P 2 i
(13.10)
NOTE: Use the required Cv, not the rated value of Cv. NOTE: When the valve has attached fittings, replace FL with FLP /FP. The sound level is:
La = 5 + L pi + T L + Lg
(13.11)
20
Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
14 Calculation flow chart*
START
4.1 THROUGH 6.4
REGIME I ? NO 8.1 THROUGH 8.4
YES
7.1 THROUGH 7.8
REGIME II ? NO REGIME III ? NO
YES 9.1 THROUGH 9.3 YES
10.1 THROUGH 10.3
NO REGIME V ? YES 12.1 THROUGH 12.4 13.1 THROUGH 13.5 YES 13.6 YES 13.7 YES
fpfo ? NO fp>fo?4fo? NO fp>4fo ?
13.8 END
13.9 THROUGH 13.11
*Numbers are equation numbers. ANSI/ISA-S75.17-1989

Not for Resale
21
--`,,,,,-`-`,,`,,`,`,,`---
REGIME IV ?
YES 11.1 THROUGH 11.3
Appendix A References
Lighthill, M. J., "On Sound Generated Aerodynamically: I. General Theory," Proceedings of the Royal Society of London, 211A (London, 1952), pp 564 - 587. Powell, A., "On the Mechanism of Choked Jet Noise," Proc. Phys. Soc. London, Sect. B., 66: 1039-57 (1953). Lighthill, M. J., "Jet Noise," AIAA Journal, 1, 1507-1517, July 1963. Fowcs Williams, J. E., and Hawkings, D. L., "Sound Generation by Turbulence and Surface in Arbitrary Motion," Philosophic Transactions of the Royal Society of London, Ser. A., 264 (London, 1969), pp 321-342.
--`,,,,,-`-`,,`,,`,`,,`---
Baumann, H. D., "On the Prediction of Aerodynamically Created Sound Pressure Level of Control Valves," ASME Paper WM/FE 28, December 1970, p. 2. Fagerlund, A. C., and Chow, D. C., "Sound Transmission through a Cylindrical Pipe Wall," ASME Journal of Engineering for Industry, Vol. 103, November 1981, pp 355-360. Shea, Allen K., "A Comparative Study of Sound Level Prediction Methods for Control Valves," Master of Engineering Report, The Pennsylvania State University, Behrend Campus, Erie, PA, August 1982. Baumann, H. D., "Coefficients and Factors Relating to Aerodynamic Sound Level Generated by Throttling Valves," Noise Control Engineering Journal, Vol. 22, No. 1, January 1984, pp 611. ANSI/ISA-S75.01-1985, Flow Equations for Sizing Control Valves, ISA, Research Triangle Park, NC 27709. Ward, W. C., and Reethoff, G., "Graphical Implementation of a Fundamentals-Based Method of Aerodynamic Control Valve Noise," American Society of Mechanical Engineers Conference on Pressure Vessels and Piping, Proceedings, Vol. 2, June 24-26, 1985. Reethoff, G., and Ward, W. C., "A Theoretically Based Valve Noise Prediction Method for Compressible Fluids," Journal of Vibrations, Acoustics, Stress, and Reliability in Design, ASME, July 1986, 00329. Baumann, H. D., "A Method for Predicting Aerodynamic Valve Noise Based on Modified Free Jet Noise Theories," ASME Paper 87-WA/NCA-7 28, December 1987.
22
Not for Resale
Appendix B Example
This is not a part of the standard, but is included to show how it is used. Values are given to more places than justified to make checking easier. Given Data 4-inch valve; maximum Cv = 210; Cv used = 210; FL = 0.8. Inlet pipe nominal 8 inch; outlet pipe same; wall is 0.322 inch. Fluid is vapor: 165 psia; density, 0.341817 lbm/ft3; T = 350F
k = 1.33
Molecular weight, 18. Downstream pressure, 70 psia; equivalent sound orifices = 1. Installed flow-to-close. Actual atmospheric pressure, 14.696 psia. The numbers on the right-hand side, for example, (4.1), are the equation numbers as used in this standard. From calculations based on ANSI/ISA-S75.01, Flow Equations for Sizing Control Valves, the following five values are calculated:
Ki FP FLP FLP/FP w
= 1.2187500 = 0.92715341 = 0.74568802 = 0.80427682 = 50247.711 lbm/hr

--`,,,,,-`-`,,`,,`,`,,`---
( P1 P2 ) P vc = P 1 ----------------------2 FL
P1 P2 FLP/FP
Result = 23760 lbf/ft2 = 10080 lbf/ft2 = 0.80427682 (FLP/F P used because fittings are attached)
(4.1)
Pvc
= 2611.7227 lbf/ft2
2 P vcc = P 1 ------------ k + 1
P1 k
= 23760 lbf/ft2 = 1.33
k ----------- k 1
(4.2)
Not for Resale
23
Result
Pvcc
= 12839.048 lbf/ft2
P 2 C = P 1 FL ( P 1 P vcc )
P1 FLP/FP Pvcc
Result = 23760 lbf/ft2 = .080427682 (FLP/FP used because fittings are attached) = 12839.048 lbf/ft2
(4.3)
P2C
= 16695.660 lbf/ft2
P1 --------- P 2 C P vcc = ---------------- = ---------P2 C P1 --------- P vcc
(4.4)
Pvcc P2C
Result
= 12839.048 lbf/ft2 = 16695.660 lbf/ft2
= 0.76900512
P1 1 - P 2 B = ----- -- , k
P1
= 23760 lbf/ft2 = 0.76900512 = 1.33
(4.5)
k
Result
P2B
= 9789.4346 lbf/ft2
P1 P 2 CE = ---------22
P1
= 23760 lbf/ft2 = 0.76900512
(4.6)
24
Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
k ----------- k 1
Result = 1404.4120 lbf/ft2 P2CE IF: Pvcc > P2 P2B ; then Regime = III (5.3) 12839.048 > 10080 > 9789.4346 Thus, regime is III.
Fd = No
No
Result = 1.0000
( 1 2 )
--`,,,,,-`-`,,`,,`,`,,`---
(6.1)
Fd
= 1.00000
Dj = NJ Fd ( Cv FL )
NJ Fd Cv FLP/FP
Result = 1.5 X 102 = 1.00 = 210.0 = 0.80427682 (fittings attached)
(1 2)
(6.3)
Dj
= 0.19494122 ft
k 1 ---------- 2 P1 k - --------1 M j = ---------- k 1 , P2
(1 2)
(6.4)
k P1 P2
Result Mj
= 1.33 = 23760 lbf/ft2 = 10080 lbf/ft2 = 0.76900512
= 1.3934534
2 T1 T vcc = -----------k+1
k T1
= 1.33 = 809.68988R
(8.1)
Not for Resale
25
Result
Tvcc
= 695.01270 R
kRg c T vcc ( 1 2 ) c vcc = ------------------------ Mw

k R Tvcc gc Mw
Result = 1.33 = 1545 ft-lbf/lbm-mole-R = 695.01270R = 32.17 lbm-ft/lbf-s2 = 18.0
(8.2)
cvcc
= 1597.6282 ft/s
k 1 ---------- k P1 k ----------- 1 P vcc ---------= 2gc ------ P1 k 1 71 (1 2)
U vcc
k Pvcc P1 1
Result = 1.33 = 12839.048 lbf/ft2 = 23760 lbf/ft2 = 0.34181735 lbm/ft3
(8.3)
Uvcc
= 1597.7712 ft/s
--`,,,,,-`-`,,`,,`,`,,`---
W ms
w Uvcc gc
Result = 50247.711 lbm/hr or 50000/3600 lbm/s = 1597.7712 ft/s = 32.17 lbm-ft/lbf-s2
wU vcc = --------------2gc
(8.4)
Wms
= 553811.56 ft-lbf/s
K III = ( 1 10 ) ( M j )
Mj = 1.3934534 = 0.80427682
( 6.6 F L )
(10.1)
FLP/FP
26
Not for Resale
Result
KIII
= 0.00041226027
W a = KIII W ms
Wms
KIII
Result = 553811.56 ft-lbf/s = 0.00041226027
(10.2)
Wa
= 228.31450 ft-lbf/s
0.2 M j c vcc f p = -----------------------Dj

cvcc
Mj Dj Result = 1597.6282 ft/s = 1.3934534 = 0.19494122 ft
(10.3)
fp
= 2283.9912 Hz
2 72 = 7 1 ------ P 1
(13.1)
1 P1 P2
Result
= 0.34181735 lbm/ft3 = 23760 lbf/ft2 = 10080 lbf/ft2
= 0.14501342 lbm/ft2
kRg c T 2 ( 1 2) c2 = ------------------- Mw
k R T2 gc Mw
= 1.33 = 1545 ft-lbf/lbm-mole-R = 809.68988R = 32.17 lbm-ft/lbf-s2 = 18.0
(13.2)
--`,,,,,-`-`,,`,,`,`,,`---
Not for Resale
27
Result
c2
= 1724.4027 ft/s
N L W a 7 2 c 2 L pi = 10 log 10 ----------------------------- 2 Di
NL Wa 2 cvcc Di
Result = 5.7 x 1010 = 228.31450 ft-lbf/s = 0.14501342 lbm/ft3 = 1597.6282 ft/s = 0.6666667 ft
(13.3)
Lpi
= 158.64638 dB
TLfo = 10 log 10
Di P 1 - a N T ------ --------------------- -----P rt 2 P p 2 o ----- + 1 P

o
(13.4)
NT Di r tp P2 Po Pa
Result
= 1.1 X 10-7 = 0.6666667 ft = 3.5 ft = 0.322/12 ft = 10080 lbf/ft2 = 2166.2241 lbf/ft2 = 2166.2241 lbf/ft2
TLfo
= 56.489620 dB
NF f o = -----------4 D i
NF
= 1.6 X 104 = 3.14159265359 = 0.6666667 ft
(13.5)
Di
--`,,,,,-`-`,,`,,`,`,,`---
28
Not for Resale
Result
fo
= 1909.8608 Hz
If fp > fo and fp
@ 4fo; then
fp T Lfp = 13 log 10 --- f o
(13.6)
2283.9912 > 1909.8608 and 2283.9912
@ 7639.4432
fp fo
Result TLfp
= 2283.9912 Hz = 1909.8608 Hz
= 1.0100050 dB
Transmission loss is: TLfo TLfp Result
T L = TLfo TLfp
(13.8)
= 56.489620 dB = 1.0100050 dB
TL
= 57.499626 dB
NP P1 Cv FLP/FP Di P2
Result
= 1.5 X 104 = 23760 lbf/ft2 = 210.0 = 0.80427682 (used because of fittings) = 0.6666667 ft = 10080 lbf/ft2
Lg
= 1.0026389 dB
La = 5 + L pi + T L + Lg
TL Lg Lpi
= 57.499626 dB = 1.0026389 dB = 158.31476 dB
(13.10)
Result
La
= 107.14939 dB (A)
Use: 107 dB (A)

Not for Resale
29
--`,,,,,-`-`,,`,,`,`,,`---
1 L g = 16 log 10 ----------------------------------------- N p P 1 C v F L 1 --------------------------- 2 D1 P2
(13.9)
Check downstream Mach: w 2 Di U2 = 50247.711 lb/hr = 0.14501342 lb/ft3 = 0.6666667 ft Volume flow = ------------------------------Flow area
50247.711 1 Volume flow = --------------------------- ------------------------------ 3600 0.14501342

= 96.2511 ft3/sec
0.6666667 2 Flow area = --------------------------- = 0.3490659 ft 2

U2 Mn2 = 275.73923 ft/sec
= ------ = --------------------------- = 0.1599
vel c
275.73923 1724.4027
Thus, calculation is appropriate.
30
Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
--`,,,,,-`-`,,`,,`,`,,`---
Not for Resale
--`,,,,,-`-`,,`,,`,`,,`---
Developing and promulgating technically sound consensus standards, recommended practices, and technical reports is one of ISA's primary goals. To achieve this goal the Standards and Practices Department relies on the technical expertise and efforts of volunteer committee members, chairmen, and reviewers. ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers United States Technical Advisory Groups (USTAGs) and provides secretariat support for International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Society's standards program, please write: ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709
ISBN: 1-55617-207-9
Not for Resale

Isa 75.17 Control Valve Aerodynamic Noise Prediction

Uploaded by

Copyright:

Available Formats

Isa 75.17 Control Valve Aerodynamic Noise Prediction

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Isa 75.17 Control Valve Aerodynamic Noise Prediction

Uploaded by

Copyright:

Available Formats

AMERICAN NATIONAL STANDARD

Control Valve Aerodynamic Noise Prediction

Approved 19 June 1991

Not for Resale

ANSI/ISA-S75.17 Control Valve Aerodynamic Noise Prediction ISBN 1-55617-207-9

Not for Resale

*One vote per company 4 ANSI/ISA-S75.17-1989

*Director Emeritus ANSI/ISA-S75.17-1989

Not for Resale

Appendix A References ..................................................................................... 22 Appendix B Example.......................................................................................... 23

Not for Resale

SI Units m/s [1] m/s m/s m m

c2 Cv cvc cvcc Dj Di Fd FL FLP

P2C P2CE Pvc

Pvcc Po r R T1 T2 Tvc Tvcc tp TL TLfo

Uvc Uvcc w Wm Wms ws Wa

Table 1 Numerical constants, N

ft/s m/s lbf/ft2 Pa

4 Pressures and pressure ratios

P1 --------- P 2 C P vcc = ---------------- = ---------P2 C P1 --------- P vcc

THEN THEN THEN THEN THEN

REGIME = REGIME = REGIME = REGIME = REGIME =

(5.1) (5.2) (5.3) (5.4) (5.5)

k ----------- P 1 k 1 2 - ---------1 M j = ---------- k 1 P 2

7 Regime I (subsonic flow)

The temperature in the vena contracta is:

Table 2 Typical No and Fd factors

The gas velocity in the vena contracta is:

The stream power of the fluid in the vena contracta is:

8 Common equations for sonic and above

The temperature in the vena contracta at sonic conditions is:

k R gc T vcc ( 1 2 ) c vcc = ------------------------ Mw

The gas velocity in the vena contracta, at critical conditions, is:

Stream power, at sonic (choked) velocity is:

The acoustic efficiency for Regime II is:

0.2 M j c vcc f p = -----------------------Dj

The acoustic efficiency for Regime III is:

0.2 M j c vcc f p = -----------------------Dj

The acoustic efficiency for Regime IV is:

0.35 c vcc f p = ---------------------------------------------------(1 2) 2 1.25 D j ( M j 1 )

The acoustic efficiency for Regime V is:

0.35 c vcc f p = -------------------------------------------------(1 2) 2 1.25 D j ( M j 1 )

The speed of sound under downstream conditions is:

P Di 1 - a N T ------ --------------------- ----- P o rt 2 P p 2 ----- + 1 P o

NOTE: The fraction Pa /Po is a correction for local barometric pressure.

The pipe coincidence frequency is:

If fp > 4fo: (13.8) Transmission loss is:

1 ----------------------------------------- N p P 1 C v F L 1 --------------------------- D2P 2 i

14 Calculation flow chart*

4.1 THROUGH 6.4

REGIME I ? NO 8.1 THROUGH 8.4

7.1 THROUGH 7.8

REGIME II ? NO REGIME III ? NO

YES 9.1 THROUGH 9.3 YES

10.1 THROUGH 10.3

fpfo ? NO fp>fo?4fo? NO fp>4fo ?

13.9 THROUGH 13.11

*Numbers are equation numbers. ANSI/ISA-S75.17-1989

YES 11.1 THROUGH 11.3

= 1.2187500 = 0.92715341 = 0.74568802 = 0.80427682 = 50247.711 lbm/hr