Scribd
Upload
67 views

Microcontroller App UnipuneTEElec

This document contains questions from an examination on microcontroller and its applications. It covers topics like 8051 architecture, addressing modes, interrupts, serial communication, interfacing 8051 with peripherals like 8255, ADC, stepper motors, keyboard etc. Programs and diagrams are required to illustrate concepts related to timers, serial communication, memory interfacing, motor control, frequency and pressure measurement using 8051 microcontroller.

Uploaded by

jupiterox
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
67 views

Microcontroller App UnipuneTEElec

This document contains questions from an examination on microcontroller and its applications. It covers topics like 8051 architecture, addressing modes, interrupts, serial communication, interfacing 8051 with peripherals like 8255, ADC, stepper motors, keyboard etc. Programs and diagrams are required to illustrate concepts related to timers, serial communication, memory interfacing, motor control, frequency and pressure measurement using 8051 microcontroller.

Uploaded by

jupiterox
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

P.T.O.

*3863362* [3863] 362


T.E. (Electrical Engineering) (Semester I) Examination, 2010
(2008 Course)
MICRO CONTROLLER AND ITS APPLICATIONS [New]
Time : 3 Hours Max. Marks : 100
Instructions : 1) Answer 3 questions from Section I and 3 questions from Section
II.
2) Answers to the two Sections should be written in separate books.
3) Neat diagrams must be drawn wherever necessary.
4) Black figures to the right indicate full marks.
5) Use of logarithmic tables slide rule, Mollier charts, electronic
pocket calculator and steam tables is allowed.
6) Assume suitable data, if necessary.
SECTION I
1. a) With a neat diagram explain the internal RAM organization of 8051. 8
b) Describe the various flags in 8051. 6
c) Explain the functions following pins 4
i) T0 (P3.4) ii)
PSEN
.
OR
2. a) Explain the use of following registers 8
i) DPTR ii) Register B iii) Program Counter iv) Accumulator
b) Compare microcontrollers and microprocessors. 6
c) Why ports P0 and P2 are unavailable for I/O operation when external memory
is interfaced? 4
3. a) Explain the various addressing modes of 8051 and give one example of each
addressing mode. 6
b) Write a program to square the contents of R5, Place the result in R0 & R1.
Store the Most significant byte of the result in R1. 6
c) Write a program to complement the contents of accumulator if P1.5=1. 4
OR

[3863] 362 -2- *3863362*


4. a) Write a program to copy an array of 16 elements from a location 30H
onwards to 50H onwards. 6
b) Explain the stack organization of 8051 and the instructions associated with
the stack. 6
c) Write an assembly language program for 8051 to select register bank 3. 4
5. a) Explain in detail the interrupt structure in 8051. 6
b) Explain the Serial Peripheral Interface (SPI) protocol. 4
c) Write a program to transfer a letter T Serially 10 times at a baud rate
of 4800. Use serial port in Mode 1. 6
OR
6. a) Write a program to generate a square waveform of frequency 2KHz on
pin P2.2. Assume the crystal frequency of 11.0592 MHz. 6
b) Write a short note on 12C Bus. 4
c) For Mode 1 of serial data communication, show the calculations for finding
out the value which is to be loaded in TH1to achieve a baud rate of 9600.
Assume the crystal frequency =11.0592 MHz. 6
SECTION II
7. a) Draw a diagram showing interfacing of 8255 with 8051 such that following
address are realized Port A - C000H, Port B - C001H, Port C - C002H &
Control word register C003H. Use full address decoding. 6
b) Explain 8051 based Assember, Compiler and Simulator 6
c) Find the address range of a memory design shown in the diagram below 4
OR

*3863362* -3- [3863] 362


8. a) 32KB of EPROM (Program memory) and 32 KB of data RAM is to be
interfaced with 8051 draw the interfacing diagram. Use full address decoding.
The starting address of EPROM is 0000H. 6
b) Write a short note on how 8051 can be interfaced with a PC. 6
c) Write a short note on features of 8255. 4
9. a) Two stepper motors are interfaced to 8051 through a driver card. The motors
are controlled through port 1. The step angle of the motor is 1.8 degree.
Draw a schematic diagram and write a program to run both the motors in
anticlockwise direction through an angle of 180 degree. 10
b) Write a short note on temperature measurement using 8051. 8
OR
10. a) Draw a typical interface of an 8 bit ADC with 8051. Write a program read 100
values from ADC and store them from memory location D100H onwards
in external Data Ram. 10
b) Write a short note on pressure measurement using 8051. 8
11. a) Explain frequency measurement using 8051 8
b) Write a short note on 8051 based DC motor control. 8
OR
12. a) Explain how a 44 matrix keyboard can be interfaced with 8051. 8
b) Write a short note on 8051 based AC motor control . 8
B/II/10/1365

You might also like