T M 10-4930-251-12&P

Technical Manual OPERATORS AND UNIT MAINTENANCE MANUAL AND REPAIR PARTS AND SPECIAL TOOLS LIST FOR

TANK, UNIT, 500 GALLON (P/N 13226E2146), LIQUID DISPENSING FOR TRAILER (Ml061Al) MOUNTING
-(NSN 4930-01-370-6079)

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

HEADQUARTERS, DEPARTMENT OF THE ARMY

21 JUNE 1999

GiL,e particular attention to specific W~1IININ(iS and C:1I IIONS throughout this manual Death or hcrious injut-> ma> result it personnel t-ail to obserc,c sarct! precautions, FIRE AND EXPLOSIVE HAZ:IRDS arc prcscnt during operation ntthis quipmcnt

Jo prckcnt serious iI?jiirJ. to personnel or equipment damage. use a lifting dclice lvith a lifting capacity of at least three tons to handle tanks. Do not allo~v tank units to SLL ing back and forth while hanging in the air. DO NOT SMOKE or USE OPEN FLAME \\ithin 50 feet ( 15.24m) ofthis unit. Make sure tire extinguisher and or fire fighting equipment are available in the immediate arca before transferring fuel. He extremely careful when using a lirc cstinguisher in an enclosed arca. Provide adequate ventilation. Unit must be grounded prior to fuel transfer operations. I Jse protective equipment to pre\ent skin and eye contact with fuel. Do not drain he1 from the unit on the ground. Drain fuel into a container that can be closed. Otherwise. a FIRE HAZARD or Environmental Contamination could result. If fuel is spilled. wash the area of spillage thoroughly with Lvater. Use rubber fuel resistant gloves when replacing filter elements due to toxic effects otsome fuel additives. Dispose of filter elements in accordance with local policy. Skin may stick to metal in cold conditions. Do not touch metal parts with bare skin during cold weather. Clean parts in a well ventilated area. Avoid inhalation of solvent fumes and prolonged exposure of skin to cleaning solvent. Wash exposed skin thoroughly,. Dry cleaning solvent used to clean parts is potentially dangerous to personnel and property. Do not use near open flame or cscessi\,e heat. Flash point of solvent is 100F. (38C. to 50C.) Wear eye protection when blowing sol\,ent from parts. Compressed air used for cleaning purposes should not exceed 30 PSI (2.1 kg/cm).

a/(b blank)

TM 10-4930-251-121&P
TECHNICAL No. MANUAL HEADQUARTERS DEPARTMENT OF THE D.C. 1 ARMYWASHINGTON, 2 June

10-4930-251-12&P

TANK,

OPERATOR'S AND UNIT MAINTENANCE MANUAL (AND REPAIR PARTS AND SPECIAL TOOLS LIST) FOR UNIT, 500 GALLON(P/N 13226E2146), FOR LIQUID DISPENSING TRAILER (M1061A1 ) MOUNTING (NSN 4930-01-370-6079) 21 June 1999

FOR

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this publication. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Submit your DA Form 2028-2 (Recommended Changes to Equipment Technical Publications), through the Internet, on the Army Electronic Product Support (AEPS) website. The Internet address is http://aeps.ria.army.mil. If you need a password, scroll down and click on "ACCESS REQUEST FORM". The DA Form 2028-2 is located in the ONLINE FORMS PROCESSING section of AEPS. Fill out the form and click SUBMIT. Using this form on the AEPS will enable us to respond quicker to your comments and better manage the DA Form 2028 program. You may also mail, fax or e-mail your letter, DA Form 2028, or DA Form 2028-2 direct to: Commander, U.S. Army Tankautomotive and Armaments Command, ATTN: AMSTA-AC-NML, Rock Island, IL. 61299-7630. The email address is: [email protected]. DISTRIBUTION STATEMENT A: Approved for public release. Distribution is unlimited.

TABLE CHAPTER Section 1 I. II. III. 2 I. II. III. IV. 3 I. II. III.

OF CONTENTS Page

INTRODUCTION General Information .................................................................. Equipment Description ............................................................... Technical Principles of Operation .................................................. OPERATING INSTRUCTIONS Description and Use of Controls ................................................... Operator Preventive Maintenance Checks and Services (PMCS) ............. Operation Under Usual Conditions ................................................ Operation Under Unusual Conditions ............................................. OPERATOR MAINTENANCE INSTRUCTIONS Operator Lubrication Instructions .................................................. Operator Troubleshooting . ........................................................... Operator Maintenance Instructions ................................................

1-1 1-2 1-5

CHAPTER Section

2-1 2-2 2-9 2-13

CHAPTER Section

3-1 3-1 3-2

TM 10-4930-251-12&P

TABLE OF CONTENTS (Cont.)

CHAPTER Section

1 UNIT MAINTENANCE INSTRUCTIONS I. Repair Parts. Special Tools. and equiptment ...................................... II. Service upon Receipt ................................................................ III. Unit Preventive Maintenance Checks and Services_ 4-2 PMCS Unit Maintellance Troubleshooting................................................ 4-4 Unit Maintenance Procedures ...................................................... 4-6 Preparation For Movement or Storage ............................................. 4-27 A REFERENCES ALLOCATION MAINTENANCE CHART Introduction ........................................................................... B-1 II. Maintenance Allocation Chart ...................................................... B-4 III. Toolsand Test Equipment Requirementsfor Maintenance Allocation Chart VI. for Remarks Maintenance Allocation Chart .................................... B-6 V.Torque Requirements ................................................................ B-7 COMPONENTS OF ENDITEM AND BASICISSUE ITEMS I. Introduction ........................................................................... C-1 II.Components of End Item ............................................................ C III. Basic Items List Issue ............................................................... C-4 AUTHORIZATIONLIST ADDITIONAL Introduction ........................................................................... D-1 II. Additional AuthorizationList ...................................................... D-2 EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST Introduction ........................................................................... E-1 II. Expenldable/Durable SuIpplies and Materials List ............................... E-2 REPAIR PARTS AND SPECIAL TOOLS LIST Introduction ........................................................................... F-I II. Repair arts List ...................................................................... P F-8 III. Special Tools (Not Applicable) .................................................... Cross Reference Indexes IV. National Stock Number (NSN) Index ............................................ 1-1 V. PartNumber (P/N) Index ........................................................... 1-2

4-1 -4-1 IV. V. VI.

APPENDIX APPENDIX B Section

APPFN

I B-5

APPENDIX C Section

- 3)

APPENDIX D Section I.

APPENDIX E Section I.

APPENDIX F Section I.

APPENDIX G ILLUSTRATED LIST OF MANUFACTURED ITEMS Section I. Introduction ........................................................................... G-1 INDEX ALPHABETICAL INDEX ......................................................... Index-1

ii

TM
LIST OF 1LLUSTRATIONS Figure 1-I l-2 l-3 2-l 2-2 ,2-4
2-5 2-6 2-l 2-8 2-9 2-10 2-1 I 4-l 4-2 4-3 4-4 4-5 4-6 J-7 4-8 4-9 4-10 4-l I 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 4-20 4-2 I Tank Assembly Dispensing

10-4930-251-12&P

TITLE
Trailer Mounted Liquid Dispensing Tank tinit Assemblq Angle and Bracket Assemblies .............................. .................................................................. .............................................................. .......................................................

Page
l-3 I-4 I-4 2. I 2.2 2-6 2-l 2-l 2-8 2-8 2-9 2-10 2-12 2-14 4-8 4-8 4-9 J-9 4-10 4-10 4-l I 4-12 4-12 4-13 4-14 4-14 4-16 4-19 4-20 4-2 I 4-22 4-23 4-25 4-26 4-26

Dispensing Unit Operating Controls

Dispensing Unit Operating Components ................................................... Grounding Rod (Stowed) ..................................................................... Grounding Rod Installation Operating Control Lever .................................................................. ..................................................................... ...................................................................... Tank Manhole Access . Refilling Tank Components .................................................................. Dispensing Fuel Set-up ...................................................................... Dispensing Fuel ............................................................................... ................................................................ ............................................................... ...................................................... ......................................................... ........................................................... Decal Operating Instructions Emergency Refilling Of Tank

Accessories Stowage Box Installation Tank Mounting Angle Installation Preparation for Tank Installation Angle/Bracket/Clamping Adapter

Assembly ............................................. Tank. Bottom Loading Valve Cable Connection ......................................... Tank Placement and Tie-down Locations ................................................. Angle/Bracket/Socket Adapter ,4ssembly ................................................. Tiedown Assembly Attachment ............................................................ Ground Rod Stowage ........................................................................ Interconnecting Hose Assembly ............................................................ Fuel Dispensing Hose ........................................................................ Hose Assembly ................................................................................ Nozzle Assembly .............................................................................. Control Box Assembly Control Levers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Levers Assembly Fuel Manifold Assembly Control Box Assembly Dry Disconnect Coupling .................................................................... ................................................ ..................................................................... ....................................................................... .................................................................... Control Box Assembly Control Levers

Storage Box Assembly ....................................................................... Tiedown Assembly ...........................................................................

iii/(iv blank)

TM 10-4930-251-12&P

CHAPTER

INTRODUCTION
Section I. GENERAL INFORMATION

1-1. Scope. This an operator and unit Maintenance level manual. Including Repair Partsand Special is Tools List. This manual Supports the trailer Mounted Low Profile 500-gallon liquid dispensing tank unit, which is aportable storage tank used for transporting and products. dispensing liquid petroleum 1-2. Maintenance Forms and Records. Department of the Army. forms and procedures used for mai 750, ntenance equipment willbe those prescribed by DA PAM 738 The Army Maintenance Management _Systern ( TAMMS). 1-3. Reporting Equipment ImprovementRecommendations (EIRS). If your needs unit improvement. let us know. Send us an EIR. ou, the user, re the onlyone who can tell us what Y a you do not like aboutour equipment. Let us know what\ do not like the design, you put it ona SF 368(Quality Deficiency Report). Mail it to Commander. U.S. Army Tank-Automotive and Armaments Command, ATTN: AMSTA-TR-F/MPA, Warren, Mi. 48397-5000. A reply will be mailed to you. 1-4. Destruction of of equipment to Administrative Storage Army Materielto Prevent Enemy Use. Prevent Enemy Use. 1-5. of Equipment. a. Referto TM750-244-3. Procedures for Destruction

Placement of equipment in administrative storage should be for short periods f o tirne hena w shortage of maintenance effort exists. Items Shouldbe in mission readinesswithin 24 hours or time factors as determined bv the directing authority. During the storage period appropriate maintenance records will be kept. b. Before equipment placing in administrative storage, current preventive maintenancechecks and services should be completed, shortcomingsand deficiencies should be corrected, and all existing modification work ordersshould be applied. c. Storage selection. site Inside storageis preferred for itemselected s for administrative storage. If aninside storagefacility is not vailable, a any type or style container is suitable providingit gives shelter complete from the elements. d. Refer Chapter to 4. worksite. Section VI, paragraph 4-16 For procedures to move equipment to a new

Section II.EQUIPMENT DESCRIPTION 1-6. Equipment Characteristics, Capabilities a. Portable 500-gallon storage tank, products. Tank assembly is b. Modified M1061A1 c. Lifting eyes on and equipped with welded and Features. skids,used for transporting and fabricated from aluminum. transport various onto equipment. storing liquid petroleum

series used to trailer topof tank facilitates loading

the trailer.

1-1

TM 10-4930-251-12&P

d. Hold downAssembly_consists oftwo tank mounting angles, four turnbuckles assemblies, two adapter sockets and adjustable for e. Tank filled is and dispenses through the at rear trailer. of Automatic fuel Shut-off during Control Box control tank refilling Assernbly is equipped or dispensing liquid product Major Bottom Loading, Valve at bottom loading refiling. with tank ON/OFF operations.

end angle two brackets, clamp adapte:r securing tank to thetrailer. bottom of tanknd fuel manifold a at

valveoperating Ievers_anda

fuel manifold usedto

1-7. Location andof Description a. The 5-ton application the

Components. support for (1 Figure 1-1) isuseor transporting f various the 500-gallon fuel tank. Figure 1-1) is used fortransporting equipment. InI petroleum products and this dispensing those

Trailer M1061A1 trailer provides (2,

b. Tank. Low 500-gallon profile tank products.

c. The Skids (9, Figure 1-2)are d. Manhole Cover. Cover ( 10,

usedto stabilize Mount and Figure 1-2)can be opened the if

tile Tank UnitAssembly. tank to is befilled the manhole. through )is used to control force fuel gravity lever will be connected/Used in of the Figure 1-2). operating levero t operate the

e.Control Box The Control Assembly. flow during refilling tank and this application. f. Manual Cable. The Manual Cable (5, tank bottom valve (3, loading

Box Assembly(4, Figure 1-1 liquiddispensing Only operations. one Figure 1-2)transfershe motion t Figure 1-2)on the tank 1. (

g.Loading Bottom Valves. The fuel is equipped tank with a bottom valve (3, loading Figure 1-2). The unit is equipped with a fuel manifold (3), Figure 1-1 ) onrearof the trailer. through either the the Refilled bottom loading valve (5, Figure 1-1 ),or ottom b loading port (6, Figure-11 ) athe Manifold Figure t Fuel (3, 1-1) I ) andank bottorn valve (3), the t loading FI"Lire1-2). s A the tank beingrefilled three will open automatically is all when fuel pressure applied. The is tank bottom valve (3, loading Figure 1-2)closes automatically by the jet level when the sensor tank is full. Thethers re closed when o a refilling fuel pressure is released. h. Grounding Rod. grounding The rod (7, i. Hose and Dispensing Nozzle. bottom valve (3, loading Dispensing Hose (11. operations. j. Tool Boxes. The Tool Figure 1-1 ) ispre-attached to the tank y a b strap. end to dispensing the tank

Transfer (10, Hose Figure 1-1 ) (8, 1-2)connectsat one Figure Figure 1-2). the other endto the dispensing units fuel manifold. Figure 1-1 ) and nozzle (9) are stowed, as shown, when not conducting

Boxes8. (

Figure 1-1

) provide storage area

for

accessories and/or tools.

1-2

I. 3. 3. 4. 5,

6. Bottom Loading Port Trailer 7. Grounding Rod v&trap Tank 8. Storage Box Unit Fuel Manifold Assembly 9. Nozzle Control 130s Assembly IO. Hose. Transfer Unit Bottom Loading Valve I 1. Hose. Dispensing

Figure 1-l Frailer Mounted Liquid Dispensing Tank Ilnit Assembly

l-3

TM 10-4930-251-12&P

I . IYank 2. Interlocks 3. Tank Bottom Loading Valve 4. Cable Washer 5. Cable Assembly

6. Tank Bottom Loading Valve Lever 7. Bushing. Cable Guide 8. [lose, Transfer 9. Skids IO. Manhole Assembly

Figure l-2 Tank Assembly Dispensing

The male interlocks are secured by clampin, cr adapters (23 and 24, Figure 1-3) and socket adapters (20. Figure l-3) at the female end.

k. Interlocks.

TANK SKSD FEMALE END /: ?

Figure I-i Angle and Bracket Assemblies

1-4

Thl 10-4930-251-12&P
l-9. Equipment Data. 3lanufacturers
I Tank Heta S\~stems

ModeiiPart Capacity,
1 mgll

Number

I i176F2 I16 500 gal. 56 in.

Uidth Height Weight

7 -.

71 in.
-3 0 in
500 Ibs. f.i1pt>

-Irailer D & S Manufacturing Co. Model/Part Cubic Length Width Height Weight Number

ICllOhlAI
458 cu. Ft. 232.62 in. 69 in.

Volume

37 in.
5,5 10 Ibs. Empty 15.850 Ibs. Gross

3 .

Holddown Assembl\ Model/Part Number 13226E2 146

l-10. Safety, Care and Handling. Observe all WARNINGS. CAUTIONS, and NOTES in this manual. This equipment can be hazardous if these instructions are not follo\ved.

Section
l-l 1. Storage of Fuel.

III.

TECHNICAL

PRINCIPLES

OF

OPERATION

a . The 500-gal ion I iquid dispensin, tank can be filled \\ith fuel after storage or servicing. It is ~1 recommended that the tank not be used to store fuel for more than ten ( 10) calendar days beyond the accomplished mission. 1-12. Dispensing of Fuel. NOTE
The hand
pump

is a not issued item with this equipment.

a . Using a hand pump coupled to the hand pump port on the top of the tank can also dispense fuel.
crravity flow procedures by connecting a dry disconnect b. Fuel is dispensed from the tank unit usin,u b coupling and hose and nozzle assembly to the bottom loading port at the fuel manifold. When the nozzle handle is activated. gravity takes ober. allowing fuel then to flow through hose and nozzle to be dispensed into vehicles needing refueling. c. When it is necessary to drain the contents of the tank, open the valve on the bottom of the tank

l-5/(1-6

blank)

OYEKATINC; INSTKUCTIONS
Section 1. DEXRIPTIO[VAND ([SE OF CONTROLS 2-l. General. Reference .IM IO-40.30-X613&f for cleaning instructionsip~~~~e~ltir~s on tank aw!mbl>,. file tanl\ can be used for transportin g, storing. and clispensin g all tvpes of petroleum products. I Ic>\Ic\ er. _ Only one t!, pe of petroleum product can be carried in and dispensed from the unit at ;I time.

2-2.

Operators Controls. Operators controls are shown in Figure 3- I .l.lic control In cr assembles allo~~s for the starting and stoppin,(r of tiicl flow from the tank. Wlieil the cotitrol lever ( I. Figure 2-I ) is pulled up (ON or OPEN position), the Ta~lh: bottom loading valve (3, Figure 3- I ) 0pens and allou s fuel flon throtqd~ the hose (8. Figure 2-I ) that connects to the Ilnit Fuel Manifold bottom loading \.al~,e.

to

Figure 2- 1

Dispensing Unit Operating Controls

2-1

TM 10-4930-251-12&P
2-3. Operator's Components. Hose Figure 2-2) is connected to tile front of the Unit bottom (5, loading, valve ( 12, Figure 2-2) and nozzle (6, Figure 2-2) is connected for to hose dispensing fuel. When the lever_is _(OFF or pushed CLOSED) position), the bottom loading valve at thetankcloses. stopping fuel flow. The lever the OFF is shown_in orCLOSED position in Figure 2-1. 2-2

Figure 2-2 "Dispensing Unit Operating

Components"

Section II. OPERATOR PREVENTIVE MAINTENANCE CHECKS

2-4. Operator PMCS are performed ensure to

AND
thathe t

SERVICES 2-4. General.

tankgravity and fed

operation. the Perform

checks and servicesat specified intervals. in in after mind theWARNINGS and CAUTIONS. Perform your mind theWARNINGS and CAUTIONS. (A) PMCS. Unit Maintenance. Report any Maintenance Management Systern Perform your

dispensing unitis for before during (B)

ready

a. Before you keep operate,always PMCS. b. While you keep operate, always c. After you your operate, perform d. If equipment your to fails properform. See DA

(D) PMCS.

operate refer to properly, PAM738-750, Army The

deficiencies tile Using (TAMMS).

2-2

TM 10-4930-251-12&P
2-5. Purpose of PMCS Table. This table provides a systematic servicing method ofandthe inspecting e4quipment. this way In defects canbe detected early before they become major a problem. causing the equipment to fallin its mission. The PMCStable is arranged the individual with PMCS procedurelisted in sequenceunder logical time (before, during,or after operation) to perform eachproceduredetermines interval the to which it is assigned. a Make habitof doing checksin the the sameorder each time and anything wrongwill be seen quickly. headings with in each column. be performed, andis Maintenance Worksheet. Form 2404 COIL111111 shows the Explanation a of Columns. is a list The following table descriptioninformation of found a. Item No. This shows column the identify equipment the area sequence in on of the PMCScolumns

usedto

whichthe checks andservices to are the Equipment Inspection

and

interval vdien

eachcheck

is

to

be

done.Itern c. to service

is

Clieck/Service. identify 'I'IICSC olumns C the general area to be done, explains to perform theill. 2-7. and Ilow

or specific part oil @Nlilcli the check or Equipment

Is Not ully F Mission Capable. This use because it IS unable not accept or operate equipment a when 2-8. Reporting

Column listsconditions which inaketile equipment unavailable for to perform mission, its or because it VvOLIld represent a safetv hazard. condition in the qLIIPIllCIItIs Not Readv/Avallable exists. E Column

Do

Defiiciiencii@s. Ifany problem with the equipmentis discovered during operated) be that cannot corrected at the operator/crew level, maintenance it Pain 738-750reportthe and deficiency the proper using forins. 2-9. Instructions. Preventive Maintenanceis not PMCS table. Dry-cleaning WARNING solvent limited

PMCS (or must Special

while It is being be reported.to DA Ret'er services listed in the

to performing cliecks the and

PD-680
used repeated and to clean parts is potentially to personnel and dangerous prolonged skin contact. Do not use nearopen or flaille Solvent flash point is 100-138'F a. Neep (38-60'C). it tile property. Avoid excessive Ileat.

oil

Clean. all

Dirt, grease, and debris get in oil metal surfaces. Usesoap and

way and maycoverLip a seriousproblem. Use dry-cleaning solvent waterto cleanrubber or plastic material.Ill. Bolts, try oneou y

NutsScrews. and Checkhern all for t obvious missing, looseness, bent or broken condition. You can't thern all witha tool, ut look b for chipped bare paint, metal, or rust around boltheads. If you find think is loose,ightenit, or t report it to unit maintenance If You can't tighten I it. c. Fluid Lines. Look for wear,darnaae leaks. Make around sure clamps and and fittings are a fitting or connectormean call a leak.If a leak comes loose from a is broken or worn out, report it to unit maintenance. d. Leakage Definitions. It are of tight. Wet spots connector, tighten If it.

and stains something

is necessaryo foryou t know fluid how leakage affectshe status of t yourequipment. The following definitions of the types/classesof leakage you need to knowto be able to determine the status yourequipment. Learn be and familiarwith them. When in doubt, NOTIFY SUPERVISOR! YOUR 2-3

I
T?vl 104930-251-12&p

Ixah det?iiitions for operatoricre\\ IMCS 511all be classi tied 2s ii)llo\\ h: Class I Seepage of liquid (as indicated by \vetliess or discoloration) not gxxr euougli to hrm drcups.

Class If Leaks ot liquid great enough to form drc)ps but not e~iough to cause drops to drip or run trom tlic faulty area. Class 111 Leaks of liquid great enough to form drops that fall or run or collect iii puddlch
I;llllt ;1rea.
near

Class IV L.eaks from under the tank. Slio\\~ii by either dampness of the area around the tank. or the L olume ot liquid in the tank less than it should be.

CAUTION
. . Equipment operation is allowable with minor leakage (Class I or Class II). When operating with Class 1 or II leaks continue to check them viswdly at regular intervals. Class III and Class IV leak should be reported to your supervisor or unit maintenance.

e. Paintim?. Touch-up Gravity Fed Fuel Dispensin,(7 Unit as needed. Refer to TM 43-O 139 for specific painting procedures. .

NOTE

Within designated intervals, these checks are to be performed in the order listed. If the equipment must be kept in continuous operation, check and service only those items that can be checked and serviced without disturbing the operation. Make the complete checks and services when the equipment can be shut down.

Table 2-l. OPERATOR PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)

Item to Check/ Service

I tern NO. I

Interval

Procedure Check for leaks. breaks, cracks, cuts and worn areas. Refer leaking, worn or damaged hose to unit maintenance

Not Fully Mission Capable Hoses are leaking, or damaged.

Before Hoses

war11

Before Nozzle

Nozzles are distorted, Check nozzle for distortion, corrosion and leaks. Refer distorted, leaking or corroded nozzles to unit maintenance leaking or corroded. Check for worn, frayed or corroded condition. Refer worn, frayed or corroded cable to unit maintenance. Cable is worn, frayed or corroded.

Before

Ground Cable

2-4

TM 10-1930-251-12&P Table 2-1.

Item tern

t o

Jo.
4

Inter-v al

Check,!

Not l~tdi~~ blission Procedure

Capable

Serv ice

Before Drain Valv,e and Control IHandle or Drain Before Tank

Chech c~~ntrol handle/lever for binding or damage. Chech Valve or Control valves for leahs. close control handlc~lever. Kefer worn or Lever I landle is worn or damaged. damaged v,alve or control handle/lever to unit maintenance.

Check tank for leaks, dents, cracks. or breaks. Chech interior for dirt. water accumulation or other foreign matter. Drain water accumulation. Refer leaks. dents, cracks. breaks or dirty interior to unit maintenance.

Tanh has Icaks. cracks. breaks. or dirty interior.

6 7 8 9

During Hoses During Nozzle

Hoses are leaking. Check for leaks. breaks, cracks. cuts and worn areas. Refer leaking. worn or damaged hose to unit maintenance. worn or damaged. Nozzles are distorted Check nozzle for distortion. corrosion and leaks. Refer di,storted. leaking or corroded nozzles to unit maintenance. leaking or corroded. Check for vvorn. frayed or corroded condition. Refer worn. fray.ed or corroded cable to unit maintenance. Check control handle/lever for binding or damage. Check valve for leaks, close control lever tightly. Refer worn or damaged valve or control lever to unit maintenance. Cable is vvorn, frayec or corroded. Valve or control leve is worn or damaged.

During Ground Cable During Drain Valve and Control Lever After Hoses After Nozzle

10 11

Hoses are leaking. Check for leaks. breaks. cracks, cuts and worn areas. Refer leaking, worn or damaged hose to unit maintenance. worn or damaged. Check nozzle for distortion, corrosion and leaks. Clean strainer daily. Refer distorted, leaking or corroded nozzle to unit maintenance. Check for vvorn. frayed or corroded condition. Refer worn. frayed or corroded cable to unit maintenance. Check control handle/lever for binding or damage. Check valve for leaks, close control lever tightly. Refer worn or damaged valve or control lever to unit maintenance. Nozzle is distorted. leaking or corroded. Cable is worn. frayed or corroded. Valve or control lever is worn or damaged.

17 L I3

After Ground Cable After Drain Valve and Control Lever

I4

After Tank

Tank has leaks. Check tank for leaks. dents. cracks, or breaks. Check interior for dirt. water accumulation or other foreign cracks. breaks. or matter. Drain water accumulation (see para. IO. C.). Refer dirty interior. leaks. dents. cracks, breaks or dirty interior to unit maintenance.

2-s

T1I 10-4930-251-12&P
S e c t i o n III. OPEKAIION llNDEI< ~~SIIAL, CONl)ITIONS Z-10. Grouriding Procedures.

WARNING
Fnilure to properly ground unit prior to operation could allow a static discharge (spark) \\ hich could ignite fuel or cause an explosion of fuel vapor. a. Kemovc grounding rod (3. Figure 2-3) from tank unit mounting angle. LJsing drive grounding rod three feet into ground then attach clmnp to clispensing establish ground, Figure 2-4.
liamniei-.

slide unit tv

b. Once flleling operations are completed. disconnect groundin g clamp from dispensing unit. I!sing slide hammer. withdrab grounding rod lrom ground then place it in storage position on mounting angle and secure with attaching straps. Detail A Figure Z-3.

SEE

DE-I-AIL

SEE DETAIL A

.y--z=%-~ Li i--- /, - ( --------- ------ .-_ I--------. .

Figure 2-3

Grounding Rod (Stowed)

2-6

Figure 2-4

Grounding Rod Installation

2-l 1. Operating Procetlwes a. Filling the Tank Through Bottom Loading Valve Port.
( I) Perform grounding procedures. Refer to paragraph 2-C).

WARNING
Fire hazards exist when handling fuel. Do not smoke or use open flame within 50 feet of the tank dispensing unit. (2) Check the control lever (5, Figure 2-5) and be certain it is in the OPEN position.

Figure 2-5

Operating Control Lever

2-7

I TM 10-4930-251-12&P

FILL TUBE

Figure 2-6

-ImI, Manhole Access

(4)

Attach dry disconnect coupling (3, Figure 2-7) to the fuel manifold (2. Figure 2-7).

(5) Attach hose (9. Figure 2-7) or D- 1 nozzle (3. Figure i-7) whichever is applicable. to 3 the dry disconnect coupling (3. Figure 2-7). 3 (6) Open valve on dry disconnect coupling (3. Figure i-7). fill tank. Avoid spilling liquid and do not overfill the tank. (7) When tank is filled, stop flow of fuel, close dry disconnect valve (3, Figure 2-7). Disconnect D- 1 nozzle. or Disconnect hose (9. Figure 2-7). drain and stow. Disconnect dr) disconnect coupling (3. Figure 2-7) and stow. Cap Bottom Loading Valve (2. Figure 2-7).

Figure 2-7 Refilling Tank Components

2-8

( 10) Disconnect and s;toL\ grotmdiny equipment as refcrcnccd in paragraph 2-O

b.

Dispensing Liquid.

CAUTION
When dispensing liquid, attend the nozzle constantly: Do not wedge open or block the control lever on the nozzle.
(I) Locate (2) dispensin g unit adjacent to the equipment to be fueled. _ safet> equipment.

Refer to paragraph 3-V and perform grounding procedures. 1,ocate

(3) Liquids \\ill be dispensed from tank through the bottom loading valve (2. Figure 3-7) by gravity flo\\ (4) Connect hose (5. Figure 3-8) and nozzle (6. Figure 3-8) to the Fuel Manifold bottom loading valve coupling ( 12. Figure 2-8). (5) Connect nozzle grciund clamp ( IO, Figure 2-8) or notzle ground plug ( 13. Figure 2-8) to equipment being ser\,iced. whichever is compatible.

Figure 2-8

Dispensing Fuel Set-up

2-9

TM lo-1930-251-12&P
DISPEliS

NOZZLE G R O U N D .

N OZklE GZOUrJD FLUG

h VEHiCLE FUEL TANK Dispensing Fuel

Figure 2-9

(6) Place control lever (5. Figure 2-5) in open position. Insert dispensing nozzle into tank being fileled (Figure 3-9) and squeex the nozzle lever. Dispense liquid. (7) The flow may be stopped at any time by releasin g nor.zle lever. thus closing nozzle When tank is full. dispensing is complete. (8) Remove dispensin g nozzle from tank. disconnect nozzle ground clamp or plug. . (9) Place control lever in Closed position. (I 0) Sto\v the hose (5, Figure 2-8) and nozzle assemblv (6. Figure 2-8) and cap the bottom i loading valve port (2. Figure 2-7) with dust cap as depicted. (I I ) Load safety equipment. Disconnect static ground rod as per paragraph 2-8

c. Draining the Tank.

WARNING
Do not drain petroleum products or flammable liquids on transporting equipment or the ground!
( I) (2) (3) Connect hose (8, Figure 2- I ) to bottom loading valve (3. Figure 2- I ). Position hose over the side ofthe trailer into suitable drainage container. Open Lever (I, Figure 2-l ) and drain tank.

(4) Connect hose (5. Figure 2-2), without nozzle (6, Figure 2-2) to bottom loading valve (I 2, Figure 2-2): thIS will allow you to drain frorn tank Open Lever (I, Figure 2-l ) and drain tank. (5) (6) Direct draining product into suitable container for storage or disposal. When tank is completely drained. close L,e\er ( I. Figure 2-l ).

(7) Disconnect Hose (5. Figure 2-2) or Hose (8. Figure 2-l ). Reconnect Hose (8. Figure 3I) to Fuel Manifold or stow Hose (5. Figure 2-2).

2-10

d. S h u t d o w n .
( t ) Clieck (2) to xc luet ttispensirl,
hose md Ilo//le arc s e c u r e d .

CtiecA to see that grot~tiding rod is secured.

(.<)

Check to see that tanh manttc\le co\ er- is closed securely.

(4) Remove dipstich from trnme. (5) Open tanhs manhole check quantity of
fuel remaining

in

fuel tank

NOTE

If there is insufficient fuel in the fuel tank for continued operation. or the unit is to be idle for an extended period of time. fill the fuel tank to prebent condensation from forming and contaminating the fuel. (6) Ensure that the dispensin g unit control lever is in the closed position (Figure 2- I ).
* e. Preparation for Movement. 1. Refer to paragraph 2- I0.d. and perform shutdown procedures

2 . Check that all tie down straps are securely attached to tie do\\n brackets and shackles and that all turnbuckles are tight.

WARNING

To prevent possible fuel spillage and potential fire hazard. manhole must be closed and locked before transporting. 3. Make certain manhole cover on tank is closed, latched and locked 4. Low Profile Tank Dispensin, Unit, Trailer Mounted is read\- for movement. (J

2-11

U.S. ARMY

WARNING:CROwO

AND BONO BEFORE

D U R I N G LObKING A N D D I S P E N S I N G . 1. OPEN A C C E S S C O V E R . 2 INSERT NOZZLE IN RECIRCUL4lINC FILL TUBE. z FILL ,ANK. .+ REMOVE NOZZLE WJD CLOSE ACCESS COER. DISPENSING: AITACH DRY OI5CONNECT 10 uANiFoLo 2 ATTACH HOSE WITH NOZZLE TO 0.47 DISCONNtCl. J FULL OPERATING LMR TO ON. 4. OPEN VlVVE ON DRY MSCONNECT. 5 DISPENSE FUEL 6 C L O S E YALE O N D R Y D I S C O N N E C T . 7 FUSH OPEFATINC LFVER TO OFF. 8 DFLVN HOSE AND REMOM FROM DRY DISCONNECT. 9 REMOM OR, DrSCONNECT FROM LUNIFCXD. SEE I INSIDE COVER FOR BOTTOM LOADING OPERATION i

Figure 2- 10

* Decal Operating Instructions

2-12

T M 10-4930-251-12&P

Section I\. OPERATION IrNDER UNUSliAL CONDITIONS 2- 13. Operation in Extreme Cold.
Dispensing Unit are the same as iincler precautions. The prwedures for operatin, (1 the Loit Profile l.aiih i~sual conditiollr except for tlie hIlo\\ iilg special

WARNING
Shin Inay sticii to metal in cold conditions. Do not touch metal parts \citli bare skin during cold \kcatlier

a Check all couplingjoints to avoid freeLing.

b. c.

and drain hater iiiorc tiqiieiitly

tliail i~sual and at each slitit cl~~wi~

Provide shelter to prevent sno\v or ice from enterin,(7 unit \\iien opened during servicing If possible provide a heated shelter.

2-14. Operation in Extreme Heat. The procedures for operating the Low Profile Tank
Dispensing Unit are the same as lmder usual conditions except for the following special precautions. a. Locate dispensing unit in shaded area, where possible, and wet down the tank with wntcr to reduce heat.

2-15.

Operation in Dusty or Sandy Areas. The procedures for operating the Low Profile Tank Dispensing Unit are the same as under usual conditions except for tile following special precautions.
a. Take advantage of natural barriers when possible, or, if necessary. erect artificial barriers to protect unit from blowing dust and sand. b. Clean the dispensing unit with an approved cleaning solvent, b(riving special attention to cavities. corners, and partially exposed interior spaces. Dry thoroughly. Keep tank and areas around the bottom loading valve and control handle free from sand and dust. c. Ensure inlet plugs and outlet caps are installed when hoses, couplings. and nozzle are removed or disconnected.

2-16.

Operation in Rainy or Humid Conditions. The procedures for operating the Lo\\; Profile Tank Dispensing Unit are the same as under usual conditions except for the following special precautions.
a. Water must be drained from the tank more often than normal conditions.

b. Erect a shelter to prevent the entrance of rain into the interior of the tank when it is opened for servicing.

2-13

TM 10-4930-251-12&P

Salt mater corrodes metal. If unpainted equipment parts are exposed to salt hater. clean them off irnmediatel~~ \\ itli an approved solvent and dry thoroughly. All surfaces SI~OLIICI be cleaned daily. b. Wipe clown the dispensin,(1 unit \vitli a liglitlv oiled rag to prevent corrosion

2-18. Operation at High Altitudes. The procedures for operating the Low Profile

Tank

Dispensing Unit are the same as under iisunl conditions except for the following special precautions.

2-19. Emergency Procedures.

In a situation where clean filtered fuel is needed but the correct hose coupling to connect to the bottom loadin g valve port is not available. it will be necessary to till the tank through the manhole. Perform the follo\ving procedures to refuel tank through maniiole fill opening.
a. b. Refer to paragraph 2-9 and perform grounding procedures. Attach nozzle grounding clamp (10. Figure 2-l I ) to fuel tank being serviced.

c. Open manhole latch (9, Figure 2-l I) and till cap (8. Figure 2-1 1) d. Insert file1 supply nozzle (6, Figure 2-I I) into till tube (7, Figure 2- 1 I) of tank and fill tank.

e. When tank is full. withdraw fuel nozzle. close fill cap and latch then disconnect nozzle grounding clamp. f. Discomect static grounding rod, and return it to its stowed position.

FILL TUBE NOZZLE GROUNDING CLAMP

Figure 2-l I

Emergency Retilling

of Tank

2-14

TM 10-1930-251-12&P

CHAPTER 3 OPERATOR MAINTENANCE INSTRUCTIONS

Section I. OPERATOR LUBRICATION INSTRI_sCTIONS

3-l.

General.

a. There are no lubrication requirements prescribed for the tank unit. b. Refer to TM 9-2330-376 l-!&P for lubrication recluirements of the modified M I06 I A I five-ton, four wheel. trailer chassis.

Section II. OPERATOR TROUBLESHOOTING

3-2.

Introduction.

a. This section contains troubleshooting information for locating and correcting most of the operating problems, which may develop with the tank dispensing unit. Table 3-l lists the common malfunctions, which you may find durin g operation of the tank or its components. Each malfunction for an indib idual component, unit, or system is followed by a list of tests or inspections that will help you determine probable causes and corrective actions to take. You should perform the tests, inspections and corrective actions in the order listed. b. This manual cannot list all the malfunctions that might occur. nor all the tests, or inspections and corrective actions. If a malfunction is not listed or is not corrected by listed corrective action, notify your supervisor or unit maintenance. Table 3-l. OPERATOR TROUBLESHOOTING MALFUNCTION TEST OR INSPECTION CORRECTIVE ACTION
1. UNABLE TO BOTTOM LOAD TANK. Step I. Check for adequate supply pressure. Notify supervisor. Step 2. Bottom loading port/valve obstructed. Disconnect nozzle and check port/valve for foreign material. Step 3. If problem still exists: Refer to Unit Maintenance.

3-1

T M 10-1930-251-12&P Table 3-1. OPER.r\T<)R TROliBLESMOO?IN(; 2. I:UL;l, FI,OW W1l.l. NO I Sl-OP Wt IEN IANK IS Fl.iLL. Step I Check for operator control le\,er in ON position. Move le\,er to CI.OSED position. Step 3. If malfunction still exists: Shut off tlo~. refer to Unit Maintenance. 3. FLOW OF PRODUCT SI,OWS DOWN DIJRING OPERATION. Step I. Check for leak in hose or connections. Tighten connection or replace hose. Step 2. If malfunction still exists: Shut off flow. refer to Unit Maintenance. 4. PRODUCT LEVEL, IN TANK DROPS BEFORE OPERATION. Step 1. Check -for operator control lever in OPEN position. Move lever to CLOSED position. Step 2. Check bottom loading valve at bottom of tank for leaks. Tighten valve. Step 3. If problem still exists: Refer to Unit Maintenance. 5 . PRODUCT DISCHARGE IS NOT CLEAN. Step 1. Check strainer in nozzle for contamination Clean nozzle strainer. Step 2. Check liquid in tank for contamination. Drain a portion of the liquid to remove contamination in bottom of tank Step 3. If problem still exists: Refer to Unit Maintenance. (Cont.)

Section III. OPERATOR MAINTENANCE INSTRUCTIONS

3-3. General. Operator maintenance on Low Profile Tank Dispensing Unit consists of only those tasks and procedures stated in the Operator Preventive Maintenance Checks and Services (PMCS) Chart. Refer to the Operators PMCS Chart and perform all tasks outlined at the intervals stated in the chart. 3-2

TNI 10-4930-251-12&P CHAPTER UNIT MAINTENANCE 4 INSTRUCTIONS AND EQUIPMENT

Section 1. REPAIR

PARTS, SPECIAL TOOLS,

4-1. Tools and Equipment. Tools or equipment required for maintenance of tile unit can be found in Appendix B. Section III,Test, Measurement and Diagnostic Equipment or support equipment to include standard test equipment are found in any unit maintenance shop. 4-2. Special Tools and Equipment. There are no special tools and equipment that are required by the unit maintenance personnel for maintenance of the unit. 4-3. Repair Parts List. F. UnitMaintenance Repair Parts and Equipment are listed in Appendix

Section II. 4-4. Inspect Equipment.

SERVICE

UPON RECEIPT

a. Inspect identification plates for positive Identification of equipment. b. Inspect the equipment for damage incurred during shipment. If the Equipment has been damaged, report the damage oil SF 364, Report of Discrepancy (ROD). c. Check equipment against packing list to make Sure all items are accounted for. Report all discrepancies in accordance with DA PAM 738-750. d. Inspect components for loose or missing mounting hardware and for loose connections. 4-5. Preliminary Servicing and Installation of Equipment. a. Servicing. (1) Lubricate the Trailer in accordance with the instructions in TM 9-2330-376-14&P. (2) Perform preventive maintenance checks and services (PMCS) as described in Table 4-1 and correct all deficiencies. b. Installation. The tank unit will be used mounted oil skids and secured on a modified Model M1061A1, 5-ton Trailer. (1) Low\ Profile Tank Unit mounted on M1061A1, 5-ton Trailer. Detailed installation procedures for the tie down kit and for mounting the tank unit on the M1061A1 Trailer are found in paragraph 4-10.

4-1

TM 10-4930-251-12&P

Section III. 4-6. General.

UNIT PREVENTIVE

MAINTENANCE

CHECKS

AND SER'VICES

a. To ensure the Low\ Profile Tank Dispensing Unit, Trailer Mounted is ready for operation at all times. It must be inspected systematically so that defects may be discovered and corrected before the result in seriousy damagedor failure b. The necessary\ preventive maintenance checks and services to be performed by unit maintenance personnel are listed in Table 4-1 and described in Chapter 4. Section V. c. Defects discovered during operation of the unit will be noted on DA Form 2404, (Equipment Inspection and Maintenance Worksheet), for future corrections to be made as soon as operation has ceased. Stop operation immediately if a deficiency is noted which would damage the equipment or harm personnel if operation were continued. d. Record all deficiencies, shortcomings and the corrective action taken on the DA Form 2404 at the earliest possible opportunity. 4-7. Unit Preventive Maintenance Checks and Services.

a. Table 4-1 contains a tabulated list of preventive checks and services, which must be performed by unit maintenance personnel. b. The interval column designates the required service interval. A quarterly interval is equal to three calendar months or two hundred and fifty hours of operation, whichever occurs first. c. Refer to Table 4-1 for unit maintenance checks and services.

4-2

TNI 10-4930-251-12&P Table 4-1. UNIT PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)MONTHLY SCHEDULE Item to Check/ Service Hose and Fittings

Item No. 1

Procedure Visually inspect hoses for leaks, cracks, breaks or cuts. Inspect fittings and coupling's for secure connections, drainage, and signs of leakage. Extend hose for inspection. Replace damaged hoses, fitting or defective gasket. Check nozzle for proper operation and leakage. distortion, and corrosion. Check screen for foreign matter. Replace a leaking or distorted nozzle. Clean dirty screen replace corroded screen or nozzle.

Not Fully Mission Capable Hoses, fittings or couplings are damaged or defective.

Nozzle

Nozzle leaks or is corroded or distorted.

Tank Valve Check valve for proper operation, leaks or damage. Check control cable for Secure connection, worn, binding, frayed or corroded condition. Replace damaged control or cable. Replace leaking or damaued,valve.

Control or Cable is worn, frayed or corroded or damaged. Valve leaks or is damaged.

Adapter Inspect for secure connections, damage and signs of Adapter Half leaks, Half, Quick leakage. Refer to para. 4-10 for repair. corroded or distorted. Disconnect Fuel Manifold Assembly Frame and Storage Box Tie Down Assembly Inspect for secure connections, leaks or damage. Replace damaged manifold. Inspect frame for cracks, loose and missing hardware or components. Tighten loose hardware. Inspect Tie Down assemblies for looseness. cracked welds and thread damage. Check for frayed, missing, or loose straps and turnbuckles. Tighten loose turnbuckles hand tight. Replace defective assemblies. Check the tank for leaks, dents, cracks. or breaks. Check for ruptures in the welded seams. Check the interior of the tank for dirt or contamination. Check for damaged or missing shackles and tie down links. Inspect skids for damage. Inspect the bottom loading valve for leaks. If the tank is damaged or leaking replace the tank. Refer other damage to depot maintenance for repair. Manifold leaks, is worn or damaged. Frame has Extensive damage beyond unit level of repair. Tie Downs or Turnbuckles have cracked welds or Missing. Tank has leaks, cracks or breaks. Welded seams are ruptured.

Tank Assembly

4-3

TM 10-4930-251-12&P

Table 4-1. UNIT PREVENTIVE MAINTENANCE\ CHECKS AND SERVICES (PMCS) MONTHLY SCHEDULE 9 Manhole Cover Assembly, CAUTION In freezing weather. especially during freezing precipitation, ensure the vent valve in the manhole is protected by being located under the Fill PLUGHINGE. Check the manhole gasket for damage and replace if necessary. Check for dents, cracks or breaks. Repair or replace defective manhole cover and filler cover. Ensure that the manhole mounting hardware is tight. Check to see that the manhole cover hinge and cam close tightly. 10 Coupling Half Check for signs of leakage around the valve handle shaft. Check Coupling gaskets for cracks. Inspect coupling for secure connection. Test coupling half by observing the internal valve mechanism as the handle is moved to ensure handle operates valve. Replace damaged valve or handle lever. Inspect cable for frayed, worn or corroded condition. Replace defective cable.

(Cont.)

Bolts and nuts are loose or missing Cracks or breaks exist. Cover gasket. manhole cover or filler cover are defective. Valve leaks, Valve or Control Lever Handle is worn or damaged.

11

Ground Cable

Cable is missing or defective.

Section IV. 4-8. General.

UNIT

MAINTENANCE

TROUBLESHOOTING

a. This ection contains troubleshooting information for locating and correcting problerns s which develop in the tank dispensing unit that are within the scope Of unit maintenance. Each malfunction for an individual component, unit or system is followed by a list of tests or inspections to help determine corrective actions for specific malfunctions. Perform the tests/inspections and corrective actions in the order listed. b. This manual cannot list all malfunctions that may occur, or all tests or inspections and corrective actions. If a malfunction is not listed or is not corrected by listed corrective actions, notify, your supervisor.

4-4

TNI 10-4930-2551-12&P Table 4-2. UNIT MAINTENANCE TROUBLESHOOTING

MALFUNCTION TEST OR INSPECTION CORRECTIVE

ACTION

1. PRODUCTDISCHARGEIS NOT CLEAN. Step 1. Check product in tank for contamination. Clean and purge tank interior after product is drained. Step 2. Check tank bottom loading valve strainer screen for contamination. Remove, clean and reinstall strainer screen. 2. FLOW OF PRODUCT SLOWS DOWN OR STOPS DURING OPERATION. Step 1. Check tank bottom loading valve strainer for contamination. Remove, clean and reinstall strainer screen. Step 2. Check nozzle for distortion, damage, or leaks. Repair or replace a defective nozzle. NOTE For these and other Troubleshooting Measures for the tank refer to TM 10-4930-236-13&P Step 3. Check hose assernbly for leaks or damage. Replace or repair hose assembly. PRODUCT LEVEL IN TANK DROPS BEFORE OPERATION. Step 1. Check tank for leaks. Replace the tank. Step 2. Check bottom loading valve on tank for leaks. Replace defective valve gasket, screen, or valve. Step 3. Check bottorn loading valve control handle and lever rod and rod support assembly. Repair or Replace the control handle, control lever, or rod assembly.

4-5

TM 10-4930-251-12&P

Table 4-2. UNIT MAINTENANCE

TROUBLESHOOTING

(Cont.)

4. FUEL WILL NOT BEGIN TOFLOW. Fusible link of valve operator control cable apart or control cable pulled loose. Reconnect control cable to valveoperator mechanism 5. FUEL FLOW WILL NOTSTOP WHEN TANK IS FULL.

Bottom loading valve malfunction. Drain tank and refer to next level of maintenance. 6. TANK WILL NOT BOTTOM LOAD. Step 1. Inspect jet level sensor to see if fuel is present in drain tube. If fuel is present: Refer to TM 10-4930-236-13&P for maintenance repair.

Step 2. Inspect jet level-sensor to see if fuel is present in drain tube. If fuel is not present: a. Repair or replace jet level sensor. b. Remove and check manifold to tank hose.

Section V. 4-9. General.

UNIT

MAINTENANCE

PROCEDURES

a. This section contains unit maintenance procedures as authorized by the Maintenance Allocation Chart (MAC), Appendix B of this manual. b. The Trailer Model M and its components are not addressed within this manual. Refer to TM 9-2330-376-14&P for PMCS, Troubleshooting, and Maintenance Procedures in order for you to maintain this piece of equipment. c. The Tank assembly Includes the pump port, manhole cover assembly, the bottom loading valve, control handle/lever, and tie-down assemblies. d. Before any repair is started, the Low Profile Tank Fuel Dispensing Unit. Trailer Mounted, and its components must be thoroughly vented and cleaned. Each time a component is removed _ for repair, inspection, or other maintenance action, it must be cleaned thoroughly. e. The Tank assembly Unit Maintenance is limited to those procedures outlined \within this manual. Refer to TM 10-4930-236-13&P for further unit maintenance not covered in this manual.

4-6

TM 10-4930-251-12&P

f. Read all warnnigs,

cautions,

notes and instructions

carefully\

before operating

or \working_

4-10.

Dispensing

Unit Assembly. installation

This task covers INITIAL SET-UP

Tools General Mechanics

Tool Kit, (Appendix

B. Section Ill. Item 2)

Materials Tiedown Kit for 5 Ton Trailer M1061A1 (Appendix for single tank installation. Storage Box Assembly (Appendix F, Figure 9) Trailer Assemby Refer to TM 9-2330-376-14&P General Safety Instructions

F, Figure 8). Quantities are

WARNING
Warnings, Cautions, Handling Equipment Safety Precautions specified in technical manuals and those for the facility pertaining to specific equipment will be reviewed and strictly observed. Failure to do so could result in personnel injury or fatality and/or damage to the equipment. 1. General. These installation instructions outline procedures and provide descriptive illustrations to install a single 500-gallon, Liquid Dispensing Tank Unit, mounted onto a modified M1061A1, 5-Ton Trailer. 2. Sequence. It presented, however, starting installation suitable to existing a. Installation is not necessary to follow the installation procedures in the sequence it will be advantages to become familiar with these procedures prior to so that thev can be rearranged, if necessary, in an efficient sequence. facilities. Procedures.

NOTE
Prior to start of installation, verify that all items listed in Appendix F. Figure F-8 and Figure F-9 are actually present. (3) Stowage Box Installation.

(a) Place stowage boxes (3, Figure 4-1 ) on the two existing 4-hole patterns on the flatbed trailer ( 1, Figure 4-1 ) (forward, Curbside and roadside areas of trailer). (b) Attach boxes to flatbed using four bolts (4) four washers (5). and four nuts (6) Figure 4-1.

4-7

TM 10-4930-251-12&P

3 (FLATBED) 1

5 6

Figure 4-1 Accessories Stowage Box Installation.

(4) Tank Mounting and Angle Installation. (a) Orient and positioni tank mounting angles, (7) and ( 11), on flatbed at approximately 44 inches from front edge and 19 inches from side edge in pre-existing mounting holes. See Figure 4-2. (b) Loosely attach angles to flatbed using eight bolts, (8). sixteen washers, (9), and eight nuts, (10) Figure 4-2. Move angles outboard (oil flatbed) as far as slots (in angles) will permit.

7 (FLATBED) 1 9

19 REF

44

REF

19

REF

Figurere4-2

Tank Mounting Angle Installation.

4-8

TM 10-4930-251-12&P

SEE PROC 5 SEEPROC 9 2

REF REF

RE F

TANK SKID (MALE END)

14 11 1 1 SEE PROC 7

Figure 4-3

Preparation for Tank Installation.

(c) Orient and position inboard and outboard clamping adapters, ( 12 and 13), and attach to post protruding from one skid on tank (2), using two screws ( 19), and two washers (20). Install hardware only finger tight. enough to retain adapters during positioning of tank. Repeat procedure at post on the other side. Note that positions will be reversed (inverted) to maintain the inboard position of adapter 13). See Figure 4-3 and Figure 4-4.

1 (FLATSED)

11 17 0

TANK SKID (MALE END)

GOO, 19 20 13 8 9 9 21

Figure 4-4 Angle/Bracket/Clamping,

Adapter Assembly.

4-9

TM 10-4930-251-12&P

WARNING
Seriousinjury canloccurwhen lifting. Whenan item cannotbe lifted with ease. Use two or more people or a liffing \device with a lifting capacity of at least 3--tons to handle tank. Do not allow\ unit to swing\\ back and forth while\ hanging in the air.

CAUTION
Load tank oil trailer before filling. Extreme caution should be taken in filling, tanks to avoid exceeding cross-country payload limits of transporting vehicle. (d) While tank is suspended in the air, route cable assembly (5, Figure 4-5) through guide (7) and connect cable assembly, (5) to the tank's bottom loading, valve control lever\ (6) and temporarily secure for safety. Other end will be connected at a later time.

4 6 5 7

Figure 4-5 Tank, Bottom Loading Valve Cable Connection.

NOTE
The tank Must be oriented with the Tank bottom loading valve\ facing toward the rear (Aft) of the trailer. (e) Orient and position tank (2) on flatbed and move mounting angles inboard so the angles are flush against the sides of the tank skids. Keeping mountina angle parallel to trailer edge, as much as possible, retighten its hardware. Align tank snugly against the secured angle, moving the other mounting angle with it. See Figure 4-6. -52 REFJ

El
Figure 4-6 Tank Placement and Tie-down Locations. 4-10

TM 10-4930-251-12&P

13 18 14 20 TANK SKID FEMALE END 100 19 14

25
Figure 4-7 Angle/Bracket/Socket

14 0
Adapter Assembly.

(f) Loosely attach one socket adapter (20), with the curbside end angle bracket using two screw ( 19), and two washer (14). Repeat procedure at the other skid. See Figure 4-7. (g) Starting at the secured mounting angle (25), fit the adapter, with the appropriate angle bracket assembled, into socket on that skid of the tank and loosely attach the angle bracket to the mounting angle using four screws ( 13), eight washers, ( 14), and four nuts (11). Repeat procedure on the other side. See Figure 4-7. (h) At the other end of tank, again starting at the secured Mounting angle. Attach the appropriate clamping end bracket ( 17 or 18 Figure 4-3)) to the assembled clamping adapters, on post of tank skid (step (c), above). Install two screw ( 19, Figure 4-7) and two washer ( 14, Figure 4-7) through bracket into tapped holes in the inboard adapter ( 13), Figure 4-4), finger-tight only. (i) Loosely attach clamping end bracket to mounting angle using four screw, ( 19). eight washer ( 14), and four nuts ( 11 ). Repeat procedure in steps and (h) for far-side. See Figure 4-7.

NOTE
It is preferred that the tank be shifted as far forward on flatbed as slots will allow without compromising the fit of the clamping adapters. Starting at secured mounting angle, fit all parts snugly and tighten all hardware. Refer to Appendix B, Section V, Torque Requirements.

4-11

TM 10-4930-2-51-12&P (5) Tiedown AssemblyAttachmentInstallation. (a) With tank mounted, install tie-down\ assemblies (24,. Figure 4-8) at locations shown iIn Figure 4-6. Using two washers (22) and one nut (23). Apply 325-327 ft. lbs. of torque to nuts to secure tie-downs.\. (b) Extend turnbuckles onl tie-downs,\ enough to attach hooks to shackles provided in tank. Attach, secure safety clips on hooks and draw turnbuckles. hand-tight only, to remove\ slack from tie-downs assemblies. Tighten jam nuts onl turnbuckles to secure.

s@l
21

(D

(FLA-9=D)

22

Figure 4-8 Tiedown Assembly Attachment. (6) Ground Rod Stowage Installation. (a) Run straps assemblies (27, Figure 4-9) through slots in tank mounting angle. (b) Attach (,round cable assembly (26) to ground rod (25). Wrap cable around rod. See Figure 4-9. (c) Position round rod (25) on angle and secure in place with straps.

27 26

25

Figure 4-9 Ground Rod Stowage. 4-12

TM 10-4930-251-12&P

4-11.

Hose Replacement. a. Removal b. Inspection c. Cleaning, d. Installation

INITIAL

SET-UP Tools Tool Kit, General /Mechanic's (Appendix

B, Section III, Item 2)

Materials Cleaning Solvent (Appendix E, Section II, item 1) Rags, Wiping (Appendix E, Section II, item 3) General Safety Instructions

WARNING
Do not smoke or use open flaine within 50 feet of tank fuel dispensing unit. a. Removal. ( 1) Move fuel flow control lever ( 1, Figure 2-1 ) to OFF. (2) disconnected. Position a suitable container or drip panl under point where hose is to be

(3) Hose assembly (4, Figure 4-10 ) Fuel Manifold.

is used to connect the tank to the Dispensing Unit

(a) Detach Coupling, on hose (4), from tank bottom loading valve (3, Figure 4-5) and coupling (3, Figure 4-10) from dispensing unit fuel manifold (12 Figure 4-10), remove hose.

12 18

18

15

Figure 4-10 Interconnecting

Hose Assembly.

4-13

TM 10-4930-251-12&P
(4) Hose assembly (5) is used to connect the Fuel Dispensing Unit to the nozzle. (a) Detach couplling (6) from Fuel Dispensing Nozzle and disconnect hose from at other end if connected-. Remove hose. 6

Fuel manifold

Figure 4-11

Fuel Dispensing

Hose. damage and wear. Replace

b. Inspection. Inspect hoses for cuts, leaks, deterioration, defective hoses, couplings, or adapters.

WARNING
Clean parts in a well ventilated area. Avoid inhalation of solvent fumes and prolonged exposure of skill to cleaning solvent. Wash exposed skin thoroughly. Dry cleaning solvent used to clean parts is potentially dangerous to personnel and property. Do not use open flame or excessive heat. Flash point of solvent is 100 F. (38C. to 50C). Wear eye protection when blowing solvent from parts.

WARNING
Compressed air used for cleaning purpose should not exceed 30 PSI. c. Cleaning. (I) (2) Clean metal parts with all approved solvent and dry thoroughly. Clean hose Surface with a clean dry cloth.

d. Disassembly. When any of the components which make up a hose assembly become unserviceable, disassemble hose as shown In Figure 4-12 to replace unserviceable item. 4 5 3 2 1

Figure 4-12 4-14

Hose Assembly

TM 10-4930-251-12&P e. Installation. (1) Install hose assernbly FiIgure 4-10) by ttachingcoupling to dispensingfuel (4. a _ manifold at one end and the tank bottom loading "valve port at the other end. (2) Install hose assembly (5, Figure 4-11 ) at dispensing unit fuel manifold bottom loading valve port for fuel dispensing or stow\ for use later. 4-12. Dispensing Nozzle Maintenance. This task consists of: a. Removal d. Assembly b. Disassembly c. Installation c. Repair

INITIAL

SET-UP Tools Required General Mechanics Tool Kit (Appendix B. Section III, Item 2) Pipe Wrench (Appendix B, Section III, Item 4) Materials/Parts Required Dry Cleaning Solvent (Appendix E, Section II, Item 1) Silicone Compound (Appendlx E, Section II, Item 6) Sealing Compound (Appendix E, Section II, Item 7) Rags, Wiping (Appendix E. Section II, Item 3) Suitable container O-Ring Packing (1each) (Appendix F, Figure F- 11, Item 2) Gasket (1 each) (Appendix F, Figure F- 11, Item 3) Equipment None Condition

General Safety Instructions

WARNING
Clean parts in a well ventilated area. Avoid inhalation of solvent fumes and prolonged exposure of skin to cleaning solvent. Wash exposed skill thoroughly. Dry cleaning solvent used to clean parts is potentially dangerous to personnel and property. Do not use open flame or excessive heat. Flash point of solvent is 100F. ( 38 C. to 50 C). Wear eye protection when blowing solvent from parts.

WARNING
Compressed air used for cleaning purpose Should not exceed 30 PSI.

WARNING
Silicone Compound is toxic to the skin, eyes and respiratory tract.

4-15

TM 10-4930-251-12&P

a. Removal. (1) Positiona suitablecontainerbeneathnozzle.removecap(18) andoperatenozzle lever (20) to drain any\,remaining fuel frorn nozzle. See Figure 4- 13 (2) Pull out onlcam lock arms (8) of coupling half(6) and disconnect nozzle from dispensing hose (not shown). b. Disassembly. 1) Unscrew Spout ( 1) and remove O-ring, packing (2), gasket (3). and strainer element (4) from body (5).

NOTE
Further disassembly should only be performed to the extent required for parts replacement. (2) Unscrew and remove coupling half (6). If gasket (7) is damaged. remove gasket from coupling half and replace. ( 1) Unscrew contact (9) fromi body (5) and remove static discharger. Hold nut 10) and unscrew Plug ( 11) from nut. Pull nut ( 10) from cable ( 12) only if it requires replacement. (4) To remove chain ( 15) and/or spring ( 16), spread open s-hooks ( 17) and disconnect 15) and spring ( 16). (5) Spread open the other end of s-hooks (17)to remove them from body (5) and cap 8 5 6 14 17 19 16 0 4 15 17 Figure 4-13 4-16 Nozzle Assembly 9 12 7

chain

13

10 11

TM 10-4930-251-12&P

C. Repair.

WARNING
Clean parts in a well ventilated area. Avoid Inhalation of solvent fumes and prolonged exposure of skin to cleaning solvent. Wash exposed skin thoroughly. Dry cleaning Solvent used to clean parts is potentially dangerous to personnel and property. Do not use open flame or excessive heat. Flash point of solvent is 100 (38C. to 50C). F. Wear eye protection when blowing solvent from parts. (1) Clean all metal parts with dry cleaning solvent and clean thoroughly. (2) Inspect nozzle body (5) and Spout ( 1) for damage. Check free operation of lever (20). See Figure 4-13. (3) damaged. (4) Check grounding wires( 12 and 14) for breaks, fraying and broken or missing covering. Make sure clip (13) jaws close firmly and inspect plug ( 11 ) and nut ( 10) for ally damage. If clip ( 13) or wire (12) are defective, replace complete static discharger assembly. Inspect coupling half (6) for any damage. Check the gasket (7) and replace if

NOTE
Do not shorten grounding wire to less than 18 inches between contact and clip.

(5) If grounding wire ( 14) is broken or frayed at the contact (9), it may he repaired. Hold nut ( 19) and unscrew contact (9). Pull nut from wire ( 14) and cut off the frayed portion of the wire. Trim plastic cover from the end of the wire and slide nut ( 19) over the end ( 14), allowing approximately 1/4 inch of wire to extend through nut. Use a punch, or similar tool, to spread the end of wire l/4 inch of wire to extend through nut. Use a punch, or similar tool, to spread the end of wire (14) slightly, then screw contact (9) onto nut ( 19). (6) (12). If nut (10) was removed, use the same procedure as above to Install it on wire

WARNING
Compressed air used for cleaning call create airborne particles that may enter the eyes. Pressure will not exceed 30 PSI. Eye protection required. (7) Use low pressure compressed air to dry strainer element (4) and remove ally trapped particles. Replace the strainer element if there is damage to the screen. packing (2) and gasket

(8) Replace any other parts that are damaged. Use a new 0-ring (3) at assembly.

4-17

TM 10-4930-251-12&P

d. Assemblv.

WARNtNG
Silicone compound. MIL-S-8660, is toxic to skin. eyes and respiratory tract. Skin and eye\ protection required. Avoid repeated or prolonged contact. Good ventilatlon is normally, adequate. 1) Apply silicone compound to O-ring packing (2) and install it on strainer element (4). See Figure 4-13. (2) Install strainer element (41)and gasket (3) on Spout ( 1) and screw spout into nozzle bodv (5), hand tight. (3) Screw Plug ( 11) on to nut ( 10) and install the static discharger assembIy by screwing contact (9) into nozzle body (5). (4) Connect chain ( 15 and spring (16)to s-hooks ( 17) and squeeze the s-hook closed. ) Connect the s-hooks to the body (5) and cap (18)and squeeze closed. Install the cap ( 18) on spout (5) Apply sealing compound to threads of coupling half (6) and screw coupling half into body (5). Install gasket (7). e. Installation. (1) Install nozzle assembly on dispensing hose by connecting hose to coupling half (6). (2) Close cam lock arms (8) on coupling half (6). 4-13. Control Box Assembly. This task consists of: a. Removal d. Assembly INITIAL SET-UP Tools Required General Mechanics Tool Kit (Appendix 13,Section III, Item 2) Materials/Parts Required Grease (Appendix E, Section II, Item 4) Dry Cleaning Solvent (Appendix E, Section II, Item 1 Rags, Wiping (Appendix E, Section II, Item 3) Lock-washers (4each) (Appendix F, Figure F-7, Item 6) Spring Pin (1 each) (Appendix F Figure F-7, Itern 10) Equipment Condition None 4-18 b. Disassembly c. Installation c. Repair

TM 10-4930-251-12&P

General Safety Instructions

WARNING
Do not smoke or have open flame within Dry cleaning solvent is potentially 50 feet of dispensing unit.

dangerous to personnel and property.

NOTE
Discard all mandatory replacernent parts.

NOTE
In the folloving, mainteriance procedures two cables installed are depicted. You need only concern yourself with single cable installation. That cable is installed in No. 1 (inboard) position. a. Control 1 Box Assembly Levers Maintenance. Removal. (a) Loosen nuts (1) to disconnect cables (2) frorn the adjusting bolt (3). See Figure 4-14. Remove the nuts (1) and withdraw cables (2) through bushing (4).

(b) (c)

Remove screw (5) and lock washers (6) to remove lever assembly (7) from Control Box Assembly.

2 2 4 3

No. 1

Position
No. 2 Position

Figure 4-14

Control Box Assembly

Control

Levers 4-19

TM 10-4930-251-12&P
(2) Disassembly\. (,I) Remove spring pin(10)and shaft(11 (b) (c) container (d)
14 13

Figure 4-15).

Remove roll pins (8) and yokes (9). Remove spacer ( 12),.control levers ( 13 and 14) and trip lever ( 15 frorn )

Remove fuse nuts 16), adjusting bolt (3) and nuts ( 17) from yokes (9). No. 2 Position
12

No. I Position
9

15

17 16 10

18

Figure 4-15 (3) Repair.

Control Levers Assembly.

WARNING
Dry cleaning solvent is used to clean parts and is potentially hazardous to personnel and property. Clean parts in a well ventilated area. Avoid inhalation of solvent fumes and prolonged exposure to skin. Wash exposed skin thoroughly. Do not use open flame or excessive heat. Flash point of solvent is 100F (38C to 50C). Wear eye protection when blowing solvent from parts. (a) Clean all parts with dry cleaning solvent and dry thoroughly. (b) breaks. (c) Replace all worn or damaged parts. Inspect all parts for wear and darnaue. Check levers and yokes for cracks or

4-20

TM 10-4930-251-12&P

(4) Assembly. (a) Thread nuts ( 17) on adjusting, bolts (3). Install fuse nuts ( 16) and adjusting bolts (3) in yokes (9). Attach yokes to control levers ( 13 and 14) with roll pins (8). See FIigure 4 ) 16. (b) Install trip lever ( 15 in container ( 18) and insert shaft (11 ). Install spacer ) 12) and control levers ( 13 and 14) as shaft ( ) is pushed into place. Make sure hole in shaft is aligned with hole in container boss. (c) Install spring pin (10).

(5) Installation. (a) Position lever assembly (7) on A-Frarne, reference Figure 1-1, align holes and install screws (5) and lock washers (6). See Figure 4-16. (b) Move levers (13 and 14) forward to OFF position. (c) Insert cable (2) from tank valve through bushing (4) on right side and install nut ( 1) on cable. Pull cable taut and install in groove of adjusting bolt (3). Screw nut I Onto adjusting bolt (3)) tight enough that cable (2) does not slip. See figure 4-16.

2 13
14
No. I Position

No. 2 Position

Figure 4-16

Control Box Assembly

Control Levers

4-21

TM 10-4930-251-12&P b. Fuel Manifold Maintenance. (1) Removal. (a) Pull out on cam lock handles (3) on manifold (12). See Figure4-17. (b) Disconnect hoses (4 and 5). (c) Remove nuts (7), lock washers (8), screw (9) and flat washer ( 10). (d) Remove Fuel Manifold Assembly (12) from mount (6). (2) Disassembly. (a) Remove screw (13), service adapter (14) and O-ring packing (15). (b) Remove cap (16) and lanyard (17).

18

is 3

15

13

is

17

10

Figure 4-17 (3) Repair.

Fuel Manifold Assembly.

(a) Clean manifold and service adapter with dry cleaning solvent and dry thoroughly. (b) Examine manifold for cracks or other damage. Check gasket (18) in coupling halves for damage. Replace as required. (c) Inspect thread inserts (19). If they are damaged, extract them and install new inserts. (d) Inspect service adapters for damage. Inspect fit of cap and check O-ring for damage. Replace as required. 4-22

TM 10-4930-251-12&P
(4) Assembly. (a) Install O-ring, packing ( 15) on service adapter ( 14) and insert into fuel (6). Install screws (13). See Figure 4-17.

manifold

(b) Attach lanyard (17) with screw at lower left corner position, and install cap 16) on service adapter ( 14). (5) Installation.

(a) Position fuel manifold (1-2) within control box assembly frarne mount (6) and instal flat washer ( 10), screen (9), lock washer (8) and nuts (7) . Torque to 50-55 ft. lbs. / (b) onto fuel manifold. c. Control (1 ) Box Removal. (a) Loosen nuts (1) to disconnect cables (2) from the adjustable bolt (3)). See Figure 4-14. (b) 4-14. (C) Pull out on earn lock handles (3) at Fuel manifold ( 12). See Figure 4-17. (d) Disconnect hoses (4) and (5). See Figure 4-17. Remove the nuts (1) and withdraw cables (2) through bushing (4). See Figure Make sure iaskets ( 18) are in place. Guide tank hoses (4 and 5) Into place Close earn lock handles (3). See Figure 4-17. Assembly Maintenance.

manifold

(e) Ensure that the fuel dispensing hose and nozzle are not connected to the fuel bottom loading port. (f) Loosen nuts (10) in four places and remove washer 9) and Bolts (8). See (

Figure 4-18.

7 n-t

Figure 4-18

Control Box Assembly. 4-23

TM 10-4930-251-12&P 4-14. Dry Disconnect Coupling. This task consists of INITIAL SET-UP Tools Required General Mechanics Tool Kit (Appendix B, Section III, Item 2) a. Disasserriblv b. Repair c. Assemblv

Material/Parts Required Dry Cleaning Solvent (Appendix E, Section II, Item 1) Rags, Wiping (Appendix E, Section II, Item 3) 0-Ring Packing (1 each) (Appendix F. Figure F-12, Itern 4) General Safety Instructions WARNING Parts under spring tension can cause injury. Dry Cleaning solvent is potentially dangerous to personnel and property.

NOTE The coupling is normally stowed in the accessory storage box. a. Disassembly. (1) Remove drive pin (1) and lever (2). SeeFigure 4-19. (2) Remove stuffing box (3), packing (4), packing (5), and stem (6). b. Repair. WARNING Dry cleaning solvent, P-D-680, used to clean parts is potentially dangerous to personnel and property. Avoid repeated and prolonged skin contact. Do Not use near open flarne or excessive heat. Flash point of solvent is 100 degrees F - 138 degrees F ( 38degrees C - 59 degrees C). (1) Clean all metal surfaces with dry cleaning solvent and dry thoroughly. (2) Inspect all parts for damage or wear, and replace parts as required. Discard all mandatory replacement parts. c. Assembly. (1) Install stem (6). Place packings (4 and 5) on stuffing box (3) and install box on stem. Tighten stuffing box. (2) Position handle end of lever (2) toward dust plug end of body and install lever on stem (6). (3 ) 4-24 Install drive pin (1).

TM 10-4930-251-12&P

6 5 4 3

2 Figure 4-19 Dry Disconnect Coupling 4-15. StorageBoxMaintenance. This task consistsof: INITIAL SET-UP Tools Required General Mechanics Tool Kit (Appendix B, Section III, Item 2) a. Inspection b. Repair

Materials/Parts Required Dry Cleaning Solvent (Appendix E, Section II, Item 1) Adhesive (Appendix E, Section II, Item 8) Rags, Wiping (Appendix E, Section II, Item 3) Gasket Material (Appendix G) WARNING Adhesive, General Purpose, MMM-A-23053/5 is toxic to skin, eyes and respiratory tract. Skin and eye protection required. Good ventilation is normally adequate. a. Inspection. (1) Inspect the exterior of storage box (1, Figure 4-20) for dents or scratches. (2) Open storage box door and check for torn or missing gaskets. b. Repair. (1) Knock out any minor dents. (2) Cut gaskets from bulk material. Clean surface of box with dry cleaning solvent. Apply adhesive to rubber gasket and attach to box. 4-25

TM 10-4930-251-12&P
3

FRONT

ROADSIDE

ell

CURBSIDE

Figure 4-20 Storage Box Assembly. 4-16 Tie Down Assembly Maintenance. This task consists of: a. Repair. a. Repair

This task authorizes repair by replacement of parts found worn or damaged.

[2-@8 3 2

Legend Figure 4-21 1 1. 2. 3. 4. Tiedown Assembly Hook, Safety Link, Chain Nut, Plain 5. 6. 7. 8. Turnbuckle Nut, Plain Tiedown, Chain Bolt, Ring

Figure 4-21 Tiedown Assembly.

4-26

TM 10-4930-251-12&P

Section VI.

PREPARATION

FOR MOVEMENT

OR STORAGE

4-17 a.

Dismantling Short Distance ( 1) Traller

for Movement. Movement. mounted unit. Attach a towing vehicle to the trailer and tow trailer to new

location. (2) Unit without trailer. vehicle. Provide suitable blocking b. Long Distance Movement. for the tank unit. Refer to TM 38-230-1 for instructions Move the tank unit to the new worksite with a forklift or and tie-downs to prevent the equipment from shifting.

( 1) for container (2) transport.

Provide suitable container fabrication. Provide suitable blocking

and tie-downs

to prevent the unit from shifting

during,

4-18 Reinstallation After Movement. as instructed in paragraph 4-10. 4-19 a. b. c. 4-20 storing a. b. 4-21 Short Term Storage.

Reinstall

the tank after movement

to a new work site

Drain fuel from tank, lines and manifold. Store loose components Secure grounding and equipment in storage boxes.

rod and dipstick

with straps provided. documents for information relative to

Intermediate Storage. Refer to the following the tank and other equipment. TM 38-230-1 AR 750-1 Preservation Army Material Storage.

and Packing of Military Maintenance Administrative

Equipment. Operations. 1-6. in this

Policy and Retail Maintenance

Administrative

storage is discussed in paragraph

4-22 Other Maintenance Procedures. Other maintenance procedures not covered technical manual for related equipment can be found in TM 10-4930-236-13&P

4-27/(4-28

blank)

TM 10-4930-251-12&P

APPENDIX
REFERENCES

A-1.

SCOPE publications referenced in this

This appendix lists all forms, Field manuals. and miscellaneous manual either by Title, Number, or Subject. A-2. FORMS Changes to Publications and Blank Worksheet Forms

Recommended Equipment

...........................

DA Form 2028 DA Form 2404 SF 368 SF 364

Inspection and Maintenance Report

..................................

Quality Deficiency

............................................................... ............................................................

Report of Discrepancv (ROD) A-3. FIRST AID

First Aid for Soldiers A-4. PAINTING

......................................................................

FM 21-11

Treatment

and Painting of Material

.................................................... ..............................................

MIL-STD-704R TM 43-0139

Painting Instructions for Army Material A-5. MAINTENANCE Management

The Army Maintenance

System (TAMMS-G)

....................... ..................

DA PAM 738-750 TB 750-1047 .TM 9-2330-376-14&P

Elimination of Combustibles From Interiors of Metal or Plastic Gasoline and Diesel Fuel Tanks

Operator, Unit, Direct Support and General Support Maintenance ................. Manual (including RPSTL) for Trailer, flatbed, 5-ton, 4 wheel, M1061A1

Operator's, Unit. and Direct Support Maintenance Manual and Repair Parts .... TM 10-4930-236-13&P and Special Tools (RPSTL) List for Tank and Pump Unit, Liquid Dispensing, For Truck Mounting MIL Design Tank and Pump Unit, Electric Motor Driven Model (500 Gallon) Tank. A-6. SHIPMENT and STORAGE Supplies and Equipment .... TM 38-230- 1 TM 740-90-1 ........ AR 750-1

Preservation, Packaging, and Packing of Military Administrative Arrny Materiel A-7. Storage of Equipment Maintenance

................................................ Operations

Policy and Retail Maintenance

DEMOLITION of Equipment to Prevent Enemy Use ................ TM 750-244-3

Procedures for Destruction

A-1/(A-2

blank)

TM 10-4930-251-12&P

APPENDIX
MAINTENANCE

B
CHART

ALLOCATION

Section I. INTRODUCTION B-1. GENERAL a. This section provides ageneral explanation of all maintenance and repair functions authorized at various maintenance levels. b. The Maintenance Allocation Chart (MAC) Section II designates overall authority and responsibility for the performance of maintenance functions on the identified end item or component. Implementation of maintenance functions upon end item or component will be consistent \ withassigned maintenance functions c. Section III lists special tools and test equipment required for each maintenance function as referenced in Section II. d. Section IV contains supplemental instructions or explanatory notes for a particular maintenance function. e. Section V contains standard torque requirements to be used when performing assigned maintenance functions unless otherwise specified. B-2. MAINTENANCE follows: FUNCTIONS Maintenence functions will limited to and defined as be

a. Inspect. To determine the serviceability of an item by comparing its physical, mechanical, and/or electrical characteristics with established standards through examination. b. Test. To verify serviceability by measuring the mechanical or electrical characteristics of an item and comparing those characteristics with prescribed standards. c. Service. Periodic operations required to keep an item in proper operating condition. i.e., to clean (includes decontaminate), to preserve, to drain, to paint, to replenish fuel, lubricants, chemical fluids, and to lubricate. d. Adjust. To maintain, within prescribed limits, by bringing setting the operating characteristics to specified parameters. e. Align. performance. proper or into exact position, or by

To adjust specified variable elements of an item to bring about optimum or desired

f. Calibrate. To determine and cause corrections to be made or to be adjusted on instrument or test measuring9 , and diagnostic equipment used in precision measurement. Consists of comparisons of two instruments, one of which is a certified standard of known accuracy, to detect and adjust any discrepancy in the accuracy of the instrument being compared. g. Remove/Install. To remove and install the same item when required to perform service or other maintenance functions. Install is the act of emplacing seating, or fixing into position an item, part, or ing, module (component or assembly) in a manner to allow the proper functioning of an equipment or system.

B-1

TM 10-4930-251-12&P h. Replace. To remove all unserviceable item and install a serviceable Counterpart in its place. "Replace" is authorized by\ the MAC and is shown as the third (3) position code of the SMR code. i. Repair. The application of maintenance services (inspect, test, service. adjust, align calibrate, or replace) or other maintenance actions (welding, grinding, riveting, straightening, facing, re-machining, or resurfacing) to restore serviceabilty to an item by, correcting specific damage, fault, malfunction, or failure in a part, subassembly. module (component or assembly), and item or system. j. Overhaul. That maintenance effort service/action necessarv to restore an item to a completely serviceable/operational condition as prescribed by maintenance standards in appropriate technical publications i.e., Depot Maintenance Work Requirements (DMWR). Overhaul is normally the highest degree of maintenance performed by the Army. Overhaul does not normally return an item to like new condition. k. Rebuild. Consists of those (services/actions) necessary for the restoration of unserviceable equipment to a like new condition in accordance with original manufacturing standards. Rebuild is the highest degree of material maintenance applied to Army equipment. The rebuild operation includes the act of returning to Zero those age measurements (hours/miles etc.) considered in classifying Army equipment components. B-3. EXPLANATION OF COLUMN ENTRIES IN THE MAC, SECTION II.

a. Column 1, Group Number. Column 1 lists functional group code numbers, the purpose of which is to identify components, assemblies, subassemblies. and modules with the next higher assembly. b. Column 2, Component/Assembly. Column 2 contains the names of components, assemblies, subassemblies, and modules for which maintenance is authorized. c. Column 3, Maintenance Function. Column 3 lists the functions to be performed on the item listed in column 2. For detailed explanation of these functions, see paragraph B-2. d. Column 4, Maintenance Category. Column 4 specifies, by listing a work time figure in the appropriate subcolumn(s), the category of maintenance authorized to perform the function listed in column 3. This figure represents the active time required to perform that maintenance function at the indicated maintenance category level. If the complexity of the maintenance tasks within the listed function varies at different maintenance categories, appropriate work time figures are shown for each category. The work time figure represents the averagle time required to restore an item (assembly. subassembly, component, module, end item, or system) to a serviceable condition under typical field operating conditions. This time includes, but is not limited to, preparation time (including any necessary disassembly/assembly time), troubleshooting tirne, and quality assurance/quality control time in addition to the time required to perform the specific tasks identified for the maintenance functions authorized in the maintenance allocation chart. The symbol designations for the various maintenance categories are as follows: C 0 F * * Operator or Crew. .................................... ........................ Organizational Maintenance. ........................ Direct Support Maintenance. ...................... General Support Maintenance. .................................. Depot Maintenance.

B-2

TM 10-4930-251-12&P

e. Column 5, Tools and Equipment. Column 5 specifies, by\code, those tool sets (not individual tools) and special tools. TMDE and support equipment required to perform the designated function. L Column 6, Remarks. This column shall, when applicable, contain a letter code in alphabetical order which shall be keyed to the remarks contained in Section IV. B-4. EXPLANATION SECTION III. OF COLUMNS IN TOOL AND TEST EQUIPMENT REQUIREMENTS,

a. Column 1, Reference Code. The tool and test equipment reference code correlates with a code used in the MAC, Section II, Column 5. b. Column 2, Maintenance tool or test equipment. c. Column 3, Nomenclature. Category. The lowest category, of maintenance authorized to use the

Name or identification

of the tool or test equipment.

d. Column 4, National Stock Number. e. Column 5, Tool Number. B-5. EXPLANATION

The National Stock Number of the tool or test equipiment. part number. SECTION IV.

The manufacturer's

OF COLUMNS

IN REMARKS,

a. Column 1, Reference Code.

The code recorded in Column 6, Section II. pertinent to the maintenance task/function

b. Column 2, Remarks. This column lists information being performed as indicated in the MAC. Section II.

B-3

TM 10-4930-251-12&P

Section II. (1) NUMBER 01 02 Trailer, Ton M1061A1 (2)

MAINTENANCE (3)

ALLOCATION

CHART (4) (6) (5) TOOLS REMARKS & EQUIP.

GROUP COMPONENT/ASSEMBLY

MAINTENANCE LEVEL CO FTH D

FUNCTION C

Tank, 500 Gallon

Inspect Replace Repair Inspect Replace

0.5

1.0 F 0.1 0.3 3 B

03

Hose Assemblies, Consists of Tank to Fuel Manifold and Dispensing Lever, Controls

0301

Inspect Replace Repair Inspect Replace Repair Inspect Replace Repair Inspect Inspect Repair Inspect Replace Repair

0.1 0.5 0.5 0.1 0. 3 3 A. C A, C, D 3 3 A, C A, C, D

0302

Fuel Manifold

04

Nozzle Assembly

0.1 0.2 0.5 0.1 0.1 1.0 0.1 0.5 0.5 3 3 D 3 D 3 3 A, C, D A C, D

05 06 07

Control Box Assemblv Dry Disconnect Coupling Assembly Accessory Storage Box

B-4

TM 10-4930-251-12&P

Section III. TOOL AND TEST EQ1JIPMENT REQllIREhlENTS FOR ~MAINTENANCE ALLOCATION CHART

Shop Equipment, Automotive Maintenance and Repair: C o m m o n No. I Less Power 3 0 Tool Kit, General Mechanics, Automotive Wrench Torque: Deflecting Frame End DR Style Mech l/2 Male Sq, Drive Wrench Spanner: Adjustable * Hook Type, Fixed Pivot Point 314 a n d 2 inax circumference 5 I SO-OO- 177-7033 SC 5 I SO-90-CL-N 26

120-00-247-2536

SC 49 IO-95-CL-A 74

5 120-00-288-6488 / SC -I9 IO-95-CL-A 7-i

B-5

334 10-4930-251-12&P

Section IV. REMARKS FOR MAINTEN,-INCE

- Reference Code ,2

Al.,LAKil\TIOY CHART

REMARKS

Replace Defective Hose Assembly. Replace Seal Assembly. Repair by Replacin,(r Defective Components. Refer to TM g-2330-376- 14&P for Complete Repair and Replacement. Refer to TM I O-4930-336i

13&P for Complete Repair

and

Replace Components.

B-6

TM 10-1930-251-12&P Section I. TORQ[JE REQUIREMENTS

CO..iRSE THRE.-\DS S:\E: GRADE 5

- 0
\ / Lubricated or Plated

S.-\E GR,.\DE 8 EXY

Lubricated or Plated

m!

(IN LB)

(IN LB) 32-35 75-83 (FT LB) 13-l-1 23-25 37-31 57-63 82-90 113-134 200-220 296-326 443-489 596-656 X40-924

(IN LB) 60-66 144-158 (FT LB) 35-18 44-48 70-77 106-l I7 153-168 2 12-233 376-J I4 606-667 909- IO00 1288-1417 1817-1999

(IN LB) 45-J) 108-l 19 (FT LB) 18-20 33-36 52-57 80-88 115-127 159-175 287-3 IO 455-50 I 682-750 966- 1063 1360-1496

I O-24 I J-30

43-47 96-106 (FT LB)

5 16-18 3 8- I6 7. I 6- 14 I Z-13 9 16-11 %%I I 314-10 78-9 l-8 I 18-7 I 14-7 FINE THREADS

17-19 31-34 49-54 75-83 109-170 150-165 266G3 394-433 59 l-649 794-873 1120-1232

(IN LB) I o-32 14-38 49-54 120-132 (FT LB) 5.16-24 3 8-24 7 16-20 I 3-30 916-18 ?8-18 3 4- I6 78-14 l-12 I 118-12 I I J-12 19-3 1 35-39 55-6 I 85-94 121-133 170-187 297-327 434-477 646-7 I 1 89 I-980 1240-3364

(IN LB) 36-40 86-95 (FT LB) 14-15 26-29 4 I-45 64-70 91-100 128-141 X3-245 326-359 485-534 668-735 931-1024

(IN LB) 68-75 168-185 (FT LB) 25-18 49-54 78-86 120-133 171-188 240-364 420-462 668-735 995-1096 1445-1590 2012-2213

(IN LB) 5 I-56 120-132 (FT LB) 20-22 37-41 58-64 90-99 128-141 180-198 3 15-347 50 I-550 746-82 I 1083-l I91 l509- 1660

B-7/(B-8

blank)

TM 10-1930-251-12&P

APPENDIX C COMPONENTS OF END ITEM AND BASIC ISSUE ITEMS LIST

Section I.

INTRODUCTION

C - l . Scope. This appcndis lists components of end item and basic issue items for the 500 Gallon Love Profile Tank Dispensing Unit. ftor Trailer Mounting to help \ou inventor? items required for safe and efticient operations.

C-2.

General. The Components of End Item sections:

and

Basic issue Items List arc div,ided

into the following

a. Section II Components of End Item. This listing is for intbrmational purposes onI>, and is not authority to requisition replacements. These items arc part of the end item, but are removled and separatelq packaged for transportation or shipment. As part ofthe end item. these items must be with the end item whenever it is issued or transferred between property accounts. Illustrations are furnished to assist you in identifing the items. b. Section III Basic Issue Items. These are the minimum essential items required to place the Low Profile Tank Dispensin g Unit for Trailer Mounting in operation, to operate it. and to perform emergency repairs. Although shipped separately packaged. BII must be with the Dispensing l.Jnit for Trailer Mounting during operation and whenever it is transferred between property accounts. The illustrations will assist you with hard-to-identify items. This manual is your authority to request/ requisition replacement BII, based on TOE/MTOE authorizations of the end item. C-3. Explanation of Columns. The following provides an explanation of columns found in the tabular listings. a. Column (1) - Illustration Number (Illus illustration in which the item is shown. Number). This column indicates the number of the

b. Column (2) - National Stock Number (NSN). the item and will be used for requisitioning purposes.

Indicates the National Stock Number assigned to

c. Column (3) - Part Number (P/N). Indicates the Part number assigned to the item and will be used for requisitioning purposes. cl. Column (4) - Commercial and Government Entity Code (CAGE CODE). Commercial and Government Entity Code (CAGE CODE) assigned to the item. Indicates the

e. Column (5) - Description. Indicates the Federal Item Name and. if required. a minimum description to identify and locate the item. f. Column (6) - Unit of Measure (U/M). Indicates the measure LIW~ in performing the actual operation/maintenance function. This measure is expressed by a two-character alphabetical abbreviation (e.g.. EA). g. Column (7) - Quantity Required (Qty Rqr). used with/on the equipment. Indicates the quantity of the item authorized to be

C-l

TM 10-1930-251-12&P

3 I -

:.J,

7; ,

21

23

6
15 7%

17

Figure C-l Components of End Item.

c-2

TM 10-4930-251-12&P Section II. COMPONENTS OF END ITEM

(2) NSN 2330-01-207-3533 4930-01-256-0650 M106A1

(3) --------7(4) P/N

(4)

(5) Description Trailer, 5 ton Tank, Liquid Dispensing, 500 Gal Angle,Tank Mounting Curbside

(6) U/M EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA EA

(7) Qty Rqr I

Illus/ ItemNo. 1 2 3 4

Cage Code 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 81349 81349 81718 81718 97403 97403 97403 97403

13226E2146 13228E4264 13228E4265 13228E4268

Angle, Tank Mounting Roadside Adapter, Clamping, Outboard Adapter, Clamping, Inboard Adapter, Socket Bracket, Angle, Socket End Crb. Bracket, Angle, Socket End, Rd. Bracket, Angle, Clamp End, Crb. Bracket, Angle, Clamp End, Rd. Hold Down Assembly, Tank Box, Stowage, Accessory Rod, Grounding Strap, Ground Rod Hold Down Hose Assembly, Tank to Manifold Hose, Discharge Nozzle, Fuel Dispensing Coupling Half, Quick Disconnect Control Box Assembly Manifold, Fuel Cover, Levers Gage Stick, Petroleurn

1 2 2 2 I I I 1 I 2 I 2 I I I 1 1 1 1 I

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 5210-01-083-2926 4720-00-937-2822 4930-01-352-1661 4730-01-192-1624 5975-01-050-5707 5340-01-395-8001 4930-01-281-1748

13228E4269 1322SE4272 13228E4271 1322SE4273 13228E4555 13288E4526 13228E9880 13228E4528 13219E0462 13220E5288-1 M370B06B2A890 M370B06B2A1440 1290GE-0050 OPW-1711-D2 13228E4259 13228E4261 13228E4262 13217E7144

C-3

TM 10-4930-2~ 1-12&P

e
1

i!!!

Figure C-2 Basic Issue Items.

Section III. BASIC ISSUE ITEMS LIST

(1)
Illud Item No. I 2

(2)

National Stock Number 42 10-00-775-O 127 X40-00-670-2459 N/A N/A N/A

(3) Description FSCM and Part Number Fire Extinguisher, Type 2. Class 2 W/Bracket (8 1348) O-E-9 15 Bag, pamphlet (56161) 10510977 Technical Manual TM 9-2330-376-14&P Technical Manual TM 1 O-4930-220- 13&P Technical Manual TM 1 o-4930-25 1- 12&P

(4) U/M EA EA EA EA EA

QTY RQR
I

(5)

1 I

C-4

TR/I 10-1930-251-12&P

APPENDIX D
ADDITIONAL AUTHORIZATION LIST

Section I. INTRODUCTION C-l. Scope. This appendix lists additional items authorized for the support of the Trailer Mount 500 gallon Tank Fuel Dispensing L!nit.
C-2. General. This list identities items that do not have to accompany the Tank or Trailer and that do not have to be turned in with Tank or Trailer. Thebe items are all authorized kg C-PA. MTOE. .IDA. 01 JTA.

C-3. Explanation of Listing. National Stock numbers. Descriptions. and Quantities are provided to
identify and request the additional items required to support this equipment. The items are listed in alphabetical sequence by item name under the type document (i.e.. CTA. MTOE. TDA. or JIA) which authorized the item(s).

D-l

TM 10-3930-251-12&I

Section II. ,~\DDITIOXAL~ Al~THORIZATION LIST

I i

(1)
Illud Item No.

(2)

(5)
Description CAGE and Part Number Usable On Code U/M
Et1

(6)

National Stock Number 5330-o l-004-5 1 80

QTY

RQR
I

D-2

TM IO-4930-251-12&P

APPENDIX E
EXPENDABLE/DURABLE SUPPLIES AND MATERlALS
Section

LIST

I. INTRODUCTION

E-l. Scope. This appendix lists espendable/d~~rable

supplies and materials needed to operate and maintain the Trailer Mounted Fuel Tank Dispensing Unit. These items are authorized b> C-l:1 50-070. Expendable/Durable Items (Except Medical. Class V repair parts. and Heraldic Items).

E-2. Explanation of Columns. a. Column (1) - Item Number. This number is assigned to the entry in the Iisting and is referenced in the narrative instructions to identil), the material (e.g.. Use cleaning compound. item 5. App E). b. Column (2) - Level. This column identifies the lowest level of maintenance that requires the
listed item.

. c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator/CreM
0 F H ................................... ................................... ................................... linit Maintenance Direct Support Maintenance General Support Maintenance

c.

Column (3) - National Stock Number. This is the National Stock Number assigned to the item:

use it to request or requisition the item.

d. Column (4) - Description. Indicates the Federal item name and, if required. a description to identify the item. The last line for each item indicates the Commercial and Government Entity Code ( C A G E C ) , 111 p arenthesis followed by the part number.
Indicates the measure used to performing the actual maintenance function. This measure is expressed by a two character alphabetical abbreviation (e.g.. EA. QT, LB, GAL). If the unit of measure differs from the unit of issue. requisition the lowest unit of issue that wilt satisfy requirements.

e. Column (5) - Unit of Measure U/M.

E-l

TM 10-4930-251-12&P

Section 11. EXPENI)ABLE/1)[@R.-kB[.['SUPPLILS

ANDNIATERIAL

LIST

(1)

2) Maint. Level
O

(3) National Stock Number 6850-00-664-5685 7930-00-526-2919 7920-00-148-9666 9150-00-530-6814 8030-00-889-3535 6850-00-880-7616 8030-00-543-4384 8040-00-262-9011 6810-00-240-2116

(4) Description CAGEC and Part Number Dry Cleaning solvent, ASTM D 235 Type 1(81346) Detenent. General Purpose. Liquid 5 Gal Pail Rags, Wiping Grease, Wire Rope, and Exposed Gear. (81349) MIL-G-18458 Tape, Antiseizing 1/2" X 260 (18876) 11072502 Silicone Compound (81349) MIL-S-8660 Sealing Compound (81349) MIL-S-7916 Adhesive, Rubber Base, General Purpose (81348) MMM-A-1617, Type III Trisodium-Phosphate (81348) O-S-642

(5) U/M Qt Gal Bale Can RL Tube Can, Brush Top Can Drum

Illus/ item No. 1

2
3

C C

4 5 6 7 8 9

C O O O O O

E-2

APPENDIX F UNIT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST

SECTION F-l. SCOPE. This Repair Parts and Special Tools List (RPSTL) lists and authorizes spares and repair parts. and olher special supporl equipment. if applicable, rccluircd tor pdormance o! the dispensin,~1 unit. It aiithori/c~ the requisitioning. issue, a n d diap(3sition of spares. repair parts, and special tools as indicated by the SOLI~CC. Maintcnancc and Recoverability (SIMR) codes. I. INTRODUCTION

F-2.

GENERAL.

In addition tv the Introduction. this RPSTL is divided into the following sections: a. Section II. Repair Parts List. A list of~pnrcs and repair parts authorized by this RPSTL for 11s~ in the perlormancc of maintenance. This list alao includes parts which must bc removed for rcplaccment of the authorid parts. Parts lists arc composed of functional groiips in asccndin g alphanumeric scqucncc, with the parts in each group listed in ascending ligurc and item n~inibcr scqucncc. Scndin,~7 units, brackets. lilters, and bolts shall be listcd with the component they mount on. Bulk materials arc listed hy item name secl~~ence in FIG. BULK. Rcpail parts kits arc listed scpar&ly in their own functional group. Items listed are shown on the associated illustrations. Section III. Special Tools List. A list of special tools, special TMDE, and special support equipment authorized hy this RPSTL (as indicated by Basis of Issue (BOI) intormation in the DESCRIPTION AND USABLE ON CODE (UOC) column). Tools that are components of common tool sets and/or Class VII arc not listed. Section IV Cross Reference Indexes. There are two cross-reference indexes in this RPSTL: The National Stock Number (NSN) Index and the Part Number (P/N) Index. The NSN Index relers you to the figure and item number. The P/N Index ret&s you to the figure and item number.

h.

C.

F-3. EXPLANATION OF COLUMNS (SECTIONS II AND Ill). a. h. Item No. (Column (I)]. Indicates the number LISC~ to identify items called out in the illustration. SMR Code [Column (2)J The SMR code is ;L S-position code containin g supply/requisitiolii~i~ information, maintenance category authorization criteria, and disposition instruction, as shown in the following breakout: Maintenance Code 1 -x x 4th position: Who can do complete repair* on the item. Recoverability Code A X -

Source Code 1 xx

I st two positions: How to get an item.

3rd position: Who can install, replace, or use the item.

5th position: Who determines disposition action on unserviceable items.

F-l

TM 10-4930-251-12&P
3. EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST (Continued).

Source Code PA PB PC PD PE PF PG

AoplicationlExulanation

Stock items; use the npplicablc NSN to I-equisirion/reqtlest items with these source codes. They are authorized to the level indicated by the cods entered in the 3rd position of the SMR code. NOTE Items coded PC arc suh~ject tu deterioration.

KD KF KB I MO-Made at unit level MF-Made at DS level MH-Made at GS level ML-Made at SRA MD-Made at depot

Items with these codes are not to he requestedlrcquisitioned individually. They are part of a kit which is authorized to the maintenance level indicated in the 3rd position of the SMR code. The complete kit must be requisitioned and applied. Items with these codes are not to he rcqtlisitionedlreqtlestcd individually. They must he made fi-om hulk material which is identified by the P/N in the DESCRIPTION AND UOC column and listed in Bulk material group of the RPSTL. If the item is authorized to you by the 3rd position code of the SMR code, hut the source code indicates it is made at a higher level, order the item from the higher level of maintenance. Items with these codes are not to he requested/requisitioned individually. The parts that make up the assembled item must he requisitioned or fabricated and assembled at the level of maintenance indicated by the source code. If the 3rd position of the SMR code authorizes you to replace the item, hut the sowce code indicates the item is assembled at a higher level, order the item from the higher level of maintenance.

AO-Assembled by unit/AVUM level AF-Assembled hy DSlAVIM level AH-Assembled by 1 GS level AL-Assembled by SRA AD-Assembled by depot XA

Do not requisition an XA coded item. Order the next higher assembly (refer to NOTE below). If an item is not available from salvage, order it using the CAGE Code and P/N. Installation drawings, diagrams, instruction sheets, field services drawings; identified by manufacturers P/N. Item is not stocked, Order an XD-coded item through normal supply channels using the CAGE Code and P/N given, if no NSN is available.

XB

x c

XD

NOTE
Cannibalization or controlled exchange, when authorized, may be used as a source of supply for items with the above source codes except for those items source coded XA.

F-2

TM lo-4930-251-12&P

3.

EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST (Continued).

(1)

THIRD POSITION. The maintenance code entered in the third position tells you the lowest maintenance level authorized to remove, replace, and use an item. The maintenance code entered in the third position will indicate authorization to the following levels 01 maintenance:
AuDlication/Exolanation Crew or operator maintcnancc done within unit maintcnancc. Unit level maintenance can remove, replace, and use the item

Maintenance Code
C 0

F H
L

Direct support maintenance can remove, replace, and ue the item.

General support maintenance can rcmwe, replace. and use the item.

Specialized repair activity can remove, replace, and use the item.

(2)

FOURTH POSITION. The maintenance code entered in the fourth position tells you whether or not the item is to he repaired and identifies the lowest maintenance level with the capability to do complete repair (perform all authorized repair functions). NOTE Some limited repair may he done on the item at a lower level of maintenance if authorized by the Maintenance Allocation Chart (MAC) and SMR codes.

Maintenance Code 0 F H L

AoDlication/Exolanation Unit is the lowest level that can do complete repair of the item. Direct support is the lowest level that can do complete repair of the item General support is the lowest level that can do complete repair of the item. Specialized repair activity is the lowest level that can do complete repair of the item. Nonreparable. No repair is authorized. No repair is authorized. No parts or special tools are authorized for maintenance of B coded item. However, the item may he reconditioned by adjusting, lubricating, etc.. at the user level.

Z B

F-3

TM 10-4930-251-12&P 3. EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST (Continued).

e.

Recoverabili~ Code. Recovernhility codes are assigned to items to indicate the dispnsitio~l action on unserviceable items. The rccovel-ahility code is shown in the tifth position of the SMR code as follows:

Recoverabilitv
Z

Code

ApplicationlExplanation
Nonreparable item. When unserviceable, condemn and dispose ofthe item at the level ofmaintenancc shown in the third position of the SMR code. Reparable item. When uneconomically reparable. condemn and dispose of the item at the unit Icvel. Reparable item When uneconomically rcparahle, condemn and dispose of the item at the direct support level. Reparable item. When uneconomically reparable, condemn and dispose of the item at the general support level. Reparable item. Condemnation and disposal not authorized below Specialized Repair Activity (SRA). Item requires special handling or condemnation procedures because of specific reasons (such as precious metal content, high dollar value, critical material, or hazardous material). Refer to appropriate manuals/directives for specific instructions.

J g.

NSN[Column

(3)J The NSN for the item is listed in this column.

CAGE [Column (4)]. The Commercial and Government Entity Code (CAGEC) is a five-digit code which is used to identify the manufactureer, distributor, or Government agency/activity that supplies the item. ParfNumber[Colurnn (.5)]. Indicates the primary number used by the manufactwer (individual, company, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specitications, standards, and inspection requirements to identify an item or range of items.

h.

NOTE
When you use an NSN to requisition an item, the item you receive may have a different P/N from the number listed. i. Descriptionand (1) (2) (3) (4) j. Usableon Code (UOC)[Co~umn (6)J This column includes the following information:

The federal item name, and when required, a minimum description to identify the item. P/Ns of hulk materials are referenced in this column in the line entry to he manufactured or fabricated. Hardness Critical Item (HCI). A support item that provides the equipment with special protection from electromagnetic pulse (EMP) damage during a nuclear attack. The statement END OF FIGURE appears just below the last item description in column (6) for a given figure in both the repair parts list and special tools list.

QTY[CoZumn (7)J The QTY (quantity per figure) column indicates the quantity of the item used in the hrenkout shown on the illustration/figure, which is prepared for a functional group, subfunctional group, or an assembly. A V appearing in this column instead of a quantity indicates that the quantity is variable and quantity may change from application to application.

F-4

TM 10-4930-251-12&P
4. EXPLANATION OF CROSS-REFERENCE INDEXES FORMAT AND COLUMNS.

n.

National Stock Number (NSNj Index. (1)

STOCK NUMBER COLUMN. This column lists the NSN in National item idunification numhcr (NIIN) scquencc. The NIIN consists of the last lnine digits oi the NSN.

NSN (e.g., 5185-01-574-1476) NIIN (2) (3)

When using this column to locate an item, ignore the first four digits of the NSN. However, the complete NSN should he used when ordering items by stock numhcr.

FIG. COLUMN. This column lists the number of the fiyure where the item is identified/ located. The figures are in numerical order in the repair parts list and special tools list. ITEM COLUMN. The item number identifies the item associated with the figure listed in the xljxent FIG. column. This item is also identified by the NSN listed on the satne line.

b.

Part iVumber [P/N) Index. P/Ns in this index arc listed in ascending alphanumeric sequence (vertical
armngcmcnt of letter and number combinations which places the first letter or digit of each proup in orderA through Z, followed hy the numbers 0 through 9, and each following letterordipit in like order). (1) CAGEC COLUMN. The Commercial and Government Entity Code (CAGEC) is a 5.digit numeric code used to identify the manufacturer, distrihuter 01 Government agency/activity that supplies the item. PART NUMBER COLUMN. Indicates the primary number used by the manufxturet (individual, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications, standards, and inspection requirements to identify an item or range of items. STOCK NUMBER COLUMN. This column lists the NSN for the associated part numba and manufacturer identified in the PART NUMBER and CAGEC columns to the left. FIG. COLUMN. This column lists the number of the figure where the item is identified/ located in the rzpair parts list and special tools list. ITEM COLUMN. The item number is the number assigned to the item as it appears in the figure referenced in the adjacent figure number column.

(2)

(3) (4) (5)

5.

SPECIAL a.

INFORMATION.

Usable On Code. The Usable On Code appears in the lower left corner of the Description column
heading. Usable on codes are shown as UOC... in the Description column (justified left) on the last line applicahlc item descl-iption/nomenclaturc. Uncoded or none listed items arc applicable to all models.

b.

Fabrication I~utructions. Bulk materials required to manufacture items are listed in the hulk material
functional group of this RPSTL. Part numbers for hulk material are also referenced in the Description Column of the line item entry for the item to he manufactured/fabricated. Detailed fabrication instruclions for items source coded to be manufactured or fabricated are found in Appendix G.

c.

Zndex

Numbers. Items which have the word BULK in the figure column will have an index number shown in the item number column. This index number is a cross-reference between the NSN I P/N index and the bulk material list in the repair parts list.

F-5

rM 10-4930-251-12&P
6. HOW TO LOCATE REPAIR PARTS.
a. When NSNs (1) oi PiNs Arc NOT Known:

Using the table of contents, determine the assembly gwup to which the item helon:s. This is necessary since figures are prepared for asscmhly groups and suhassemhly goups. and lists iws divided into the same @oups. Find the figure coveting the h~nctional belongs. group or the subfunctional group to which the item

(2) (3)

Identify the item on the figure and note the number(s). Look in the repair parts list for the figure and itcm numbers. The NSNs and part numhcrs on the sxne line as the associated item numhers. iwe

(4) b.

When NSN Is Kirown: (1) (2)

If you have the NSN, look in the STOCK NUMBER column 01 the NSN index. The NSN is arranged in NIIN sequence. Note the figure and item number next to the NSN. Turn to the figure and locate the item number. Verify that the item is the one you are looking for.

E.

When PIN Is Known: (1)

(2) If you have the P/N and not the NSN, look in the PART NUMBER column of the P/N index. Identify the figure and item number. Look up the item on the figure in the applicable one you are looking for. repair parts list. Vcrily that the item is the

F-6

TM 10-4930-251-12&P

Figure 1. Trailer Assembly

SECTION

II

TM 10-4930-251-12&P

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 01 TRAILER ASSEMBLY FIG. 1 TRAILER ASSEMBLY

(7) QTY

PAFHH 2330012073533

19207

8750137

TRAILER,FLAT BED SEE TM 9-2330376-14&P........................... END OF FIGURE

F-l-l

TM lo-4930-251-12&P

SECTION II

Figure 2. Tank Assembly

SECTION

II

TM 10-4930-251-12&P

(1)
I T E M NO

(2)
SMR

(3)

(4)

(5) PART

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 02 TANK ASSEMBLY FIG. 2 TANK ASSEMBLY

(7)

CODE

NSN

CAGEC

NUMBER

QTY

PDOFH 5430012560650 97403 1322632146

SEE TM loTANK,LIQUID STORAGE 4930-236-13&P...................... END OF FIGURE

F-2-l

TM

10-4930-251-12&P

SECTION

II

Figure 3. Control Box Assembly

SECTION

II

TM lo-4930-251-126P

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 03 CONTROL BOX ASSEMBLY FIG. 3 CONTROL BOX ASSEMBLY

(7)
QTY

ADO00

2 3 4 5

PA022 PA022 PAOZZ PA022

19207 12463701-l 5305007195238 80204 BlSZlBH050F200N 97403 1322834559-l 5310012317459 96906 MS51943-9 5310012664641 96906 MS51412-9

CONTROL AND MANIFOL ___........_.... SCREW,CAP,HEXAGON H................ WASHER,FLAT........................ N"T,SELF-LOCKING,HE "ASHER.FLAT........................ END OF FIGURE

1 4 4 4 4

F-3-l

TM 10-4930-251-12&P

SECTION

II

Figure 4. Fuel Manifold Assembly

SECTION

II

TM 10-4930-251-12&P

(1)
ITEM NO

(2) SMR CODE

(3) NSN

(4)
CAGEC

(5) PART NUMBER

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 03 CONTROL BOX ASSEMBLY FIG. 4 FUEL MANIFOLD ASSEMBLY

(7) QTY

2 3 4 5 6 7 8 9 10 11 12 13

PAOZZ PFOZZ XDOZZ XDOZZ PFOZZ PAOZZ PBOZZ XDOZZ

PAOZZ

5330006122414 4730009155127

4730010197432 5305009594158 1560003072780

5305007276804

96906 96906 97403 97403 96906 96906 96906 97403

96906

MS27030-6 MS27029-11 1322834261 1322632178 MS27028-13

MS24693-C273

PFOZZ PAOZZ PAOZZ PAOZZ

1560009492087 5331008758288 5310005845272 5310007680321

96906 96906 96906 96906

MS29526-2 1322834259 MS35307-414 MS24484-5 MS29513-153 MS35338-48 MS51971-5

.GASKET............. .PLUG,QUICK DISCONNE .MANIFOLD,BOTTOM.... .ADAPTER HALF,QUICK. .CAP,QUICK DISCONNEC .SCREW,MACHINE .._ .CAP,FILLER OPENING. .PLATE,MOUNTING ..__ .SCREW,CAP,HEXAGON H
.A!JAPTER,PRESSURE FU

.O-RING............. .WASHER,LOCK ..___ .NUT,PLAIN,HEXAGON END OF FIGURE

F-4-l

TM 10-4930-251-12&P

i2

Figure 5. Control Lever Assembly

SECTION

II

TM 10-4930-251-12&P

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 03 CONTROL BOX ASSEMBLY FIG. 5 CONTROL LEVER ASSEMBLY

(7) QTY

XBOZZ

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

PBOOO XBOZZ X9022 XBOZZ PFOZZ XBOZZ XEOZZ

PFOZZ

97403 1322834262 97403 1322739681-l 09310 452712 09310 442898 09310 443802 09310 444707 09310 443791 09310 443790
09310 443789

PFOZZ XBOZZ XBOZZ PFOZZ XBOZZ XBOZZ PAOZZ PAOZZ PAOZZ PBOZZ PA022

5310009291807 5310013529593 5305007195007 5310008094058

09310 09310 09310 09310 09310 09310 96906 80205 96906 97403 96906

444951 443824 444945 407843 452690 442896 MS51922-2 NAS1149C0463R MS51959-83 1322834531-3 MS27183-10

............. .COVER,PROTECTIVE .LEVER ........................ .. SPACER ...................... .. YOKE,HANDLE ................. .. PIN,ROLL .................... ..NUT,PLAIN,HEXAGON ........... ..NUT,ADJUSTING,HEXAG ......... ..N"T,PLAIN,HEXAGON ........... BOLT,CABLE ADJUSTIN, ., .___ .. SHAFT,STRAIGHT . . . . . . . . . . . . . . . . BUSHING ..................... .. CONTAINER ASSEMBLY .......... .. P I N . . . . . . . . . . . . . . . . . . . . . . . . . . . LEVER,TRIP .................. .. HANDLE ...................... .......... .N"T,SELF-LOCKING,HE .WASHER,FLAT .................. .SCREW,MACHINE ................ CABLE,BALL END ................ WASHER,FLAT ................... END OF FIGURE

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 1 1

F-5-l

TM

10-4930-251-12&P

DETAIL A 4

-, k
See Appendix C To order Grounding Rod

Figure 6. Hold Down Assembly (Sheet 1 of 2)

SECTION
TM 10-4930-251-12&P

II

RON?

TANKSKID FEm1E END> . 1.. bL> lr- J v-'

E

Figure 6. Hold Down Assembly (Sheet 2 of 2)

SECTION

II

TM 10-4930-251-12&P

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 04 HOLD DOWN ASSEMBLY FIG, 6 HOLD DOWN ASSEMBLY

(7) QTY

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

PDOOO 97403 XDOZZ 97403 PFOZZ 4010014467986 75535 XDOZZ 97403 XDOZZ 97403 MOOZZ 4010002865645 81348 PAOZZ PAOZZ PAOZZ PAOZZ PAOZZ PAOZZ XDOZZ PAOZZ WOZZ XDOZZ XDOZZ PAOZZ PAOZZ PDOZZ PDOZZ 5310012751065 5305000712071 5310012664641 5310012317459 5305000712068 96906 96906 80204 97403 96906 96906 97403 80204 97403 97403 97403 80204 96906 97403 97403

1322834528 1322637730-6 lo-14592 13228E4529-2 1322838308-13 RRC271 MS51412-13 MS51943-16 B1821BH050C200N 1322834559-l MS51412-9 MS51943-9 1322936648 B1821BH050C138N 1322834272 1322834265 1322834264 B1821BH031C250N MS51412-6 1322834269 1322834268

5306002264835 5310012590296

TIEDOWN,FUEL TANK ................. .RING,LIFTING ..................... .LINK,CHAIN,DETACHAB .............. .HOOK,SAFETY,EYE.. ................ ,TURNB"CKLE,JAW AND ............... .CHAIN,WELDED MAKE FROM CHAIN,P/N RRC271,2 LINKS LONG,. ............. WASHER,FLAT ....................... NUT,SELF-LOCKING,HE ............... SCREW,CAP,HEKAGON H ............... WASHER,FLAT ....................... WASHER,FLAT ....................... NUT,SELF-LOCKING,HE ............... BRACKET,ANGLE ..................... SCREW,CAP,HEKAGON H ............... ADAPTER,SOCKET,TANK ............... ANGLE,TANK MOUNTING ............... ANGLE,TANK MOUNTING ............... BOLT,MACHINE ...................... WASHER,FLAT ....................... ADAPTER,CLAMPING,IN ............... ADAPTER,CLAMPING,OU ............... END OF FIGURE

4 1 3 1 1 1 8 4 32 56 56 32 4 8 2 1 1 4 4 2 2

F-6-l

TM

10-4930-251-12&P

SECTION II

SEE DETAIL A

SEE DETAIL A

Figure 7. Ground Rod Assembly

SECTION

II

TM

10-4930-251-12&P

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONAND"SABLEONCODES(UOC) GROUP 04 HOLD DOWN ASSEMBLY FIG. 7 GROUND ROD ASSEMBLY

(7) QTY

1 2 3

PAOZZ 5340013958001 97403 13220E5288-1 PFOZZ 6150004833918 97403 13219E3930 PFOZZ 5975010505707 97403 1321930462

STRAP,WEBBING...................... 2 C A B L E ASSEMBLY,POWE .._ 1 ROD,GROUND ..__.__................. 1 END OF FIGURE

F-7-l

cc

SECTION

II

TM 10-4930-251-12&P

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONAND"SABLEONCODES(UOC) GROUP 05 ACCESSORY STOWAGE BOX ASSEMBLY FIG, 8 ACCESSORY STOWAGE BOX ASSEMBLY

(7) QTY

1 2 3 4

97403 1322834263 XDOZZ PAOZZ 5305002253843 130204 B1821BH025ClOON PAOZZ 5310008094058 96906 MS27183-10 PAOZZ 5310009291807 96906 MS51922-2

BOX,STOWAGE,ACCESSO ................ SCREW,CAP,HEXAGON H ................ WASHER,FLAT ........................ N"T,SELF-LOCKING,HE ................ END OF FIGURE:

2 8 8 8

F-8-1

TM 10-4930-251-12&P

SECTION

II

Figure 9. Hose Assemblies

SECTION

II

TM 10-4930-251-12&P

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTION AND USABLE ON CODES (UOC)

(7)
QTY

GROUP 06 HOSE ASSEMBLY FIG. 9 HOSE ASSEMBLIES 1 2 3 4 5 PBOZZ PAOZZ PAOZZ PAOZZ PBOZZ 4720009372622 5330006122414 4730011921624 81349 96906 96906 96906 81349 M370B0622A1440 MS27030-6 MS49002-9 MS49001-9 M370B06B2A0540 HOSE ASSEMBLY,NONME ................ GASKET ............................. COUPLING HALF,QUICK ................ COUPLING HALF,QUICK ............. HOSE ASSEMBLY,NONME ................ END OF FIGURE 1 1 1 1 1

F-9-1

SECTION TM 10-4930-251-12&P

11

1I

10

16 4 15/

Figure 10. Fuel Dispensing Nozzle Assembly

SECTION

II

T M 10-4930-251-12&P

(1)
ITEM NO

(2) SMR CODE

(3)
NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTION ANDUSABLEONCODES(UOC) GROUP 06 HOSE ASSEMBLY FIG. 10 FUEL DISPENSING NOZZLE ASSEMBLY

(7) QTY

58536 A-A-52030TYPE1,S IZE2 PAOZZ 4930001190452 81718 296CA-4000 XDOZZ 81718 H-3804-AG PFOZZ 4030008030272 81718 H3673M XAOZZ 81718 H-9209-M PFOZZ PBOZZ PBOZZ PBOZZ XAOZZ PAOZZ PFOZZ XAOZZ
PAOZZ

PA000

NOZZLE,FUEL AND OIL................ 1 ASSEMBLY,DUST................. .CAP,DUST PART OF 296CA-4000 . . .HOOK,CHAIN,S P A R T O F 296CA-4000 .SPRING,COMPRESSION PART OF 296CA.dOOO.............................. .CHAIN,NOZZLE PART OF 296CA-4000 .SPOUT ASSEMBLY.................... .O-RING............................ .STRAINER ELEMENT,SE _.__.._........ .BODY NOZZLE....................... .DISCHARGER,ELECTROS . . . . . . . . .CLIP,ELECTRICAL PART OF MS25384-1 .CABLE PART OF MS25384-l .......... .CONTACT,ELECTRICAL PART OF MS25384-l.......................... .PL"G,TIP PART OF MS25384-l....... .COMPRESSION NUT,ELE PART OF MS25384-l..........................
.CAP END

1 1
1

2
1

7 8 9 10 11 12 13 14 15 16

4930001209602 4930004057544 5331011030958 4730009893260

5999012078412

81718 81718 81718 81718 81718 96906 81718 81718 96906

HD-9597-RB 190GT-1 l/2 H7670M 153-11/2X15/8 D546A MS25384-1 H5482M H5132RS MS25384-3

1 1 1 1 1 1
1

1 1 2

PFOZZ 5935000079202 96906 MS3493-1 PFOZZ 96906 MS3493-2

OF FIGURE

F-10-1

TM

10-4930-251-12&P

SECTION

II

,/

5 I

4 I

Figure 11, Dry Disconnect Coupling Assembly

SECTION

II

TM lo-4930-251-12CP

(1) ITEM NO

(2) SMR CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 07 DRY DISCONNECT COUPLING ASSEMBLY FIG. 11 DRY DISCONNECT COUPLING ASSEMBLY

(7) QTY

1 2 3 4 5 6 7 8 9 10 11 12 13

XAOOO PFOZZ PFOZZ PAOZZ XDOZZ XDOZZ PBOZZ PBOZZ XDOZZ XDOZZ XDOZZ XDOZZ PFOZZ

4730009155127 4730000889285 5330006122414

5331013596707 5331013598778

4730012540217

97403 96906 96906 96906 97403 t-31718 81718 81718 81718 81718 81718 81718 96906

1322834534 MS27029-11 MS27026-11 MS27030-6 1322632177 c-3140-RE H-6281-M H-7725-M H-7724-M C-1123-Dl H-4466-M H-4464-M MS27029-13

COUPLING ASSEMBLY .................. .PLUG,QUICK DISCONNE ............... .COUPLING HALF,QUICK ............... .GASKET ............................ .CO"PLING HALF,QUICK ............... .STEM PART OF 1322632177 .......... .O-RING PART OF 1322632177 ........ .O-RING PART OF 1322632177 ........ .STUFFING BOX PART OF 1322632177 .LE"ER PART OF 1322632177 ......... .BOLT PART OF 1322632177 .......... .NUT PART OF 1322632177 ........... .PLUG,QUICK DISCONNE.. ............. END OF FIGURE

1 1 1 1 1 1 1 1 1 1 1 1 1

F-11-1

SECTION

II

TM 10-4930-251-12&P

(1) ITEM NO

(2) skfa CODE

(3) NSN

(4) CAGEC

(5) PART NUMBER

(6) DESCRIPTIONANDUSABLEONCODES(UOC) GROUP 08 GENERAL USE STANDARDIZED PARTS FIG. BULK

(7) QTY

PAOZZ 4010002865654 81348 RRC271

CHAIN.WELDED....................... END OF FIGURE

BULK-1

SECTION

IV

TM 10-4930-251-12&P

STOCK

NUMBER

CROSS REFERENCE INDEXES NATIONAL STOCK NUMBER INDEX STOCK NUMBER ITEM FIG. 10 6 6 11 10 10 6 6 BULK 4 10 9 7 10 4 4 9 11 5 3 4 4 10 5 8 4 4 11 5 8 9 4 4 10 4 7 10 9 10 3 6 11 2 6 3 6 6 5 11 11 15 14 9 3 2 6 2 18 1 7 7 4 2 16 12 1 2 4 18 2 9 13 4 20 3 11 2 2 16 4 1 10 6 9 5 3 8 3 14 4 12 13 1 19 5 11 7 17 7 8 5340-01-395-8001 4010-01-446-7986

FIG. 7 6

ITEM 1 3

5935-00-007-9202 5305-00-071-2068 5305-00-071-2071 4730-00-088-9285 4930-00-119-0452 4930-00-120-9602 5305-00-225-3643 5306-00-226-4835 4010-00-286-5645 1560-00-307-2780 4930-00-405-7544 4730-00-432-7448 6150-00-483-3918 5935-00-503-8979 5310-00-584-5272 5330-00-612-2414

5305-00-719-5007 5305-00-719-5238 5305-00-727-6804 5310-00-768-0321 4030-00-803-0272 5310-00-809-4058 5331-00-875-8288 4730-00-915-5127 5310-00-929-1807 4720-00-937-2822 1560-00-949-2087 5305-00-959-4158 4730-00-989-3260 4730-01-019-7432 5975-01-050-5707 5331-01-103-0958 4730-01-192-1624 5999-01-207-8412 5310-01-231-7459 4730-01-254-0217 5430-01-256-0650 5310-01-259-0296 5310-01-266-4641 5310-01-275-1065 5310-01-352-9593 5331-01-359-6707 5331-01-359-8778

I-1

TM 10-4930-251-12&P

SECTION IV

CAGEC
58536 80204 80204 80204 80204 80204 81718 81718 81718 81718 81718 81718 81718 81718 81718 81718 81718 81718 81718 81718 81718 96906 96906 96906 96906 96906 96906 96906 96906 96906

PART NUMBER A-A-52030TYPE1,S IZEZ B1821BH025ClOON B1821BH031C250N B1821BH050C138N B1621BH050C200N B1821BH050F200N C-1123-Dl C-3140-RE D546A H-3804-AG H-4464-M H-4466-M H-6281-M H-7724-M H-7725-M H-9209-M HD-9597-RB H3673M H5132RS H5482M H7670M
MS24484-5

CROSS REFERENCE INDEXES PART NUMBER INDEX STOCK NUMBER

FIG.

ITEM 1
2 18 14 9 2

10
5305-00-225-3843 5306-00-226-4835 5305-00-071-2068

8
6 6 6 3

5305-00-071-2071 5305-00-719-5238

11 11
10 10 11

10
6 10 3 12

5331-01-359-6707 5331-01-359-8778 4930-00-120-9602

4030-00-803-0272

MS24693-C273
MS25384-1

5331-01-103-0958 1560-00-949-2087 5305-00-959-4158 5999-01-207-8412 4730-00-088-9285 4730-01-019-7432 4730-00-915-5127 4730-01-254-0217 5330-00-612-2414 5310-00-809-4058 5331-00-875-8288
1560-00-307-2780

11 11 11 11 10 10 10 10 10 10
4 4

11
7

9 8
5 6 4

13 12 8 10
6

M.S25384-3 MS27026-11 MS2702fJ-13 MS27029-11 MS27029-13

MS27030-6

10 10 11
4 4

11 14
3 5 2 2

11 11
4

13 1
2 4 20 3

9
96906 96906 96906 96906 96906 96906 96906 96906 96906 96906 96906 96906 96906 96906

MS27183-10 MS29513-153 MS29526-2 MS3493-1

MS3493-2

11 5 8 4 4

11
7 15

5935-00-007-9202 5935-00-503-8979
5305-00-727-6804 5310-00-584-5272 4730-00-432-7448

10 10
4 4

MS35307-414
MS35338-48 MS49001-9

16 9
12 4 3 7

MS49002-9 MS51412-13 MS51412-6 MS51412-9 MS51922-2 MS51943-16

4730-01-192-1624 5310-01-275-1065 5310-01-259-0296 5310-01-266-4641 5310-00-929-1807

9 9
6 6 3 6 5

19
5

11
16 4

8
6

I-2

SECTION IV

TM lo-4930-251-12&P

CAGEC 96906 96906 96906 81349 81349 80205 81348 75535 19207 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 97403 81718 81718 81718 09310 09310 09310 09310 09310 09310 09310 09310 09310 09310 09310 09310

PART NUMBER MS51943-9 MS51959-83 MS51971-5 M370B06BZA0540 M370B06B2A1440 NAS1149C0463R RRC271 10-14592 12463701-l 1321930462 1321933930 1322035288-l 13226E2146 1322632177 1322632178 1322637730-6 1322739681-l 1322834259 1322834261 1322834262 1322834263 1322834264 1322834265 1322834268 13228E4269 1322834272 1322834528 1322834529-2 1322834531-3 13228E4534 1322834559-l 13228E8309-13 1322936648 153-11/2X15/8 190GT-1 l/2 296CA-4000 407843 442896 442898 443789 443790 443791 443802 443024 444707 444945 444951 452690

CROSS REFERENCE INDEXES PART NUMBER INDEX STOCK NUMBER 5310-01-231-7459 5305-00-719-5007 5310-00-768-0321 4720-00-937-2822 5310-01-352-9593 4010-00-286-5645 4010-01-446-7986 5975-01-050-5707 6150-00-483-3918 5340-01-395-8001 5430-01-256-0650

FIG. 3 6 5 4 9 9 5 6 BULK 6 3 7 7 7 2 11 4 6 5 4 4 5 8 6 6 6 6 6 6 6 5 11 3 6 6 6 10 10 10 5 5 5 5 5 5 5 5 5 5 5 5

ITEM 4 12 18 13 5 1 17 6 1 3 1 3 2 1 1 5 4 2 2 8 3 1 1 17 16 21 20 15 1 4 19 1 3 10 5 13 9 7 2 13 15 4 9 8 7 5 11 6 12 10 14

4730-00-989-3260 4930-00-405-7544 4930-00-119-0452

I-3

n-5 10-4930-251-12&P

SECTION

IV

CAGEC 09310

PART NUMBER 452712

CROSS REFERENCE INDEXES PART NUMBER INDEX STOCK NUMBER

FIG. 5

ITEM 3

I-4

TM 10-4930-251-12&P

APPENDIX G
ILLUSTRATED LIST OF MANUFACTURED ITEMS
Section 1. INTRODUCTION
G-l. This appendix includes complete instructions for authorized manufactured or fabricated item(s) at Unit Maintenance. G-2. All bulk materials needed for manufacttlreifabrication are listed by part number or specification number in a tabular list on the illustration. G-3. A part number index in alphanumeric order is provided for cross-referencing the pan number of the item to be manufactured to the figure which covers fabrication criteria.

PART NUMBER INDEX

PART NO. 13226E2149-I I 13226E2149-13 FIGURE NO. G-l G-l

G-l

TM 10-4930-251-12&P

NOTES:
I. 2. FABRICATE FROM SYNTHETIC RUBBER. PART NO. MIL-R-6855. CLASS I> GRADE 40 DIMENSIONS ARE IN INCHES.

G-2

TM 10-4930-251-12&P

INDEX

Page,
Subject Figure, Table, Number A Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessory Stowage Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Location and Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PMCS, Unit Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repair ....................................................................................... Replace ....................................................................................... Additional Authorization List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................................................ Administrative Storage of Equipment B Bottom Loading Port, Fuel Manifold .. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l-2 Bottom Loading Valve, Fuel Manifold Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I-2 .. PMCS. Operator and Unit Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T2-l,T4-I . Troubleshooting, Operator and Unit Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TSl,T4-2 Bottom Loading Valve, Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T;-l.T4-2 .. Troubleshooting C Column Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Coupling, Dry Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 4.24 F-7 4-25 4-8 l-3 T-l-l 4-25 F-9 D-l l-6

D
Decals ............................................................................................. 2. I I I-I 4-27 2-10 4-27 4-27

Destruction of Army Material to Prevent Enemy Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..................................................................... Dismantling for Movement Preparation for Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short Distance Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Long Distance Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Index-l

TM 10-4930-251-12&P

Dispensing of Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5 Technical Principles of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5 Dispensing Liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 .............................................................................. Dispensing Nozzle 4.15 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-3 ................................................................................. PMCS T?-l,T4-I Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T 3-I. T4-2 Draining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

E
Emergency Refilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 .................................................................. Emergency Procedures, Operation 2-l Equipment Characteristics. Capabilities and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-2 Equipment Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-5 capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-i .................................................................................... Manufacturers 1-5 Weight and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-5 Explanation of Columns ..................................................................... C-l, E-l Explanation ofColumns Section I and II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-l Explanation of Columns Section IV. V. and VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-5 Explanation ofColumns In MAC. Section II ................................................... E-2 Explanation of Columns In MAC, Section III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3 Explanation of Columns In MAC, Section IV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 ...................................................... Explanation of Columns In BII; Section III C-l Explanation of Listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-l F Fuel Manifold General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Inspection, Cleaning, and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T2-l,T4-I 4-22 Maintenance ,.......,.....................................,......................,..............

G
Grounding Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9

H
Hand Driven Dispensing Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand Receipt (-HR) Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hose Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspection. Cleaning and Repairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hose Assembly Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to Locate Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 l-l l-3 4-13 4-l F-l

Index-2

TM 10-4930-251-12&P I
Inspect and Clean Tank Assembly General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....................................................................................... operator PMCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unit PMCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspect Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation of Tie Down Kit for 5- ton Trailer Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspection

4-7 4-l T2-I T4-I 4. I 3-12 4-26 4-S

L
Location and Description of Major Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bottom [Loading Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................................................................ Control Box Assembly Dispensing Nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grounding Rod ................................................................................. Hose Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manhole Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Skids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-2 l-2 l-2 l-3 I-2 l-3 l-3 l-2 l-2 l-2 l-3 l-2 3. I

M
Maintenance Forms and Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-l B-l

Manhole Cover Assembly r2-I. r 4-l Cleaning. Inspection, and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................................................................. T2-I Operator PMCS T4-I Unit PMCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0
Operating Instructions on Decals and Instruction Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Lever Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dispensing Liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining the Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergenc)~ Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filling the Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 4-19 2-8 2-10 2-13 2-7

Index-3

TM 10-4930-251-12&P

Operation in Dust or Sandy Areas ............................................................ Operation in Extreme Cold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation in Extreme Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation in High Altitudes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation in Rainy or Humid Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-12 2-12 2-12 2-13 2-12

Operation in Salt Water Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.13 Preparation For Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 ..................................................................... 2-10 Shutdown 2-10 Operators Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-l Inspecting, Cleaning, and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T 2 -I. T 4 -I 4.18.4.l9.4-20,4-21 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P Painting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preliminary Servicing and Installation of Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....................................................................................... Installation ....................................................................................... Servicing Preparation for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparation for Storage or Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparation for Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 4-I 4-l 4-I 4-21 4-21 2-10

Preventive Maintenance Checks and Services 2-2. T 2-l Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....................................................................................... Units 4.2. T 4 -I Principles of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-5

R
Reinstallation After Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repair Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reporting Deficiencies (QDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reporting Equipment Improvement Recommendations (EIR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 A-l F-l l-l i. l-l

S
Safety. Care and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a. I-5 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-l Special Instructions, Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 B-3. B-5. F-l, F-34 Special Tools and Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Administrative .............................................................................. Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................................................................... Short Term Storage Box Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage of Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-I. 4-27 4-27 4-27 4-25 l-5

Index-4

TM 10-1930-251-12&P

Tank Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-2. 2-4. 4-3. 4.7. ................................................... 3-4.4.3.4.7.-1-12.4-26. Tie Down Assemblq~ Tools and equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-I. B-3. Trailer Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-2. Troubleshooting Tables Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . u Unit Preventive Maintenance Check and Services .......................................

F-2 F-8 B-5 F-I

r i-l. 3-l T 4-2, 4-5

T4.I. 4-3

Index-!Y(lndex-6 blank)

--

RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBUCAllONS

SOMETHING WRONG

WlTHTHlSPUBLICATION?

TM 1 O-4930-251 -12&P

15JUN99

Title of TM

E EXACT.. .PIN-POINT WHERE IT ISlb 4 THIS SPACE TELL WHAT IS WRONG A ,ND WHAT SHOULD BE DONE ABOUT IT: AGE :lGURE lABLE NO. ;RAPH NO. NO. -

PArU-

-193 -227

Step No. 1 says to connect LH 4 SPNSN Unit-8 hose from Nhere to what? It is also not identified. rocedure is continued from another page, but cap is not ,emoved - add step to procedure.

RINTED NAME,

&DE 0

TELEPHONE NUMBERS

SIGN HERE:

Doe, John

:PL
PRMCUS EDITIONS ARE OBSOLEIE.

CPL John Doe

P.S.-IF YOUR OUTFIT WANTS TO KNOW ABOUT YOUR RECOMMENDATlON MAKE A CARBON COPY OF THIS AND GIVE IT TO YOUR HEADQUARTERS.

DA ,%Y% 2028-2

RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS

SOMETHING WRONG
DATE SENT PUBUCATION TITLE

WITH THIS PUBLICATION?

FROM: (PRINT YOUR UNITS COMPLETE ADDRESS)

PU8LICATION DATE

TM 1 o-4930-251 -12&P
,E EXACT. . .PIN-POINT WHERE IT IS PAGE NO. ?ARAiRAPH IGURE NO. lABLE NO. -

21 JUN 99

Tank Unit, 500 GAL

4 THIS SPACE TELL WHAT IS WRONG ND WHAT SHOULD BE D0NE ABOUT IT:

RINTE

AME.

nE, AND TELEPHONE NUMBERS

DA I%!% 2028-2

PREVIOUS EDITIONS ARE OBSOLETE.

P.S.-IF YOUR OUTFIT WANTS TO KNOW ABOUT YOUR RECOMMENDATION MAKE A CARBON COPY OF THIS AND GIVE IT TO YOUR HEADQUARTERS.

FOLD BACK _ _

DEPARTMENT OF THE ARMY

I IIII I

OFFICAL BUSINESS

BUSINESS REPLY MAIL

FIRST CLASS BRM PERMIT NO. 82 ROCK ISLAND, IL POSTAGE WILL BE PAID BY ROCK ISLAND ARSENAL

Director Armament and Chemical Acquisition and Logistics Activity ATTN: AMSTA-AC-NML Rock Island, IL 61201-9948

RECOMMENDED CHANGES 70 EQUIPMENT TECHNICAL PUBLICATIONS WITH THIS PUBLICATION?

TM 1 o-4930-251 -12&P
E EXACT. . .PIN-POINT WHERE IT IS DAGE NO. AMiRAPH GURE NO. ABLE NO. -

21 JUN 99

I Tank Unit, 500 GAL

4 THIS SPACE TELL WHAT IS WRONG - A,ND WHAT SHOULD BE DONE ABOUT IT:

RINTED NAME, GRADE 0

nE, AND TELEPHONE NUMBERS

SIGN HERE:

DA ,%!% 2028-2

P.S.--IF YOUR CUlFlT WANTS TO KNOW ABOUT YOUR RECOMMENDATION h+AKE A CARBON COPY OF THIS AND GIVE IT TO YOUR HEADQUARTERS.

FOLD BACK -

DEPARTMENT OF THE ARMY NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES

OFFICAL BUSINESS

BUSINESS REPLY MAIL

FIRST CLASS BRM PERMIT NO. 82 ROCK ISLAND, IL POSTAGE WILL BE PAID BY ROCK ISLAND ARSENAL

Director Armament and Chemical Acquisition and Logistics Activity ATTN: AMSTA-AC-NML Rock Island, IL 61201-9948

RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS

SOMETHING WRONG
@kF THEN ... JOTDOWNTHE 0 DOPE. 1; OPE, THE'V ABOUT IT ON THIS FORM. CAREFULLY TEAR IT R THii OUT OUT. FOLD IT AND DROP IT IN IN THE MAIL! M PUBILICATI,@N DATE DATE SENT PUBUCATION TITLE

WITH THIS PUBLICATION?

FROM: (PRINT YOUR UNIT'S COMPLETE ADDRESS)

PUBLICATION NUMBER

TM 10-4930-251-12&p

21 JUN 99

Tank Unit, 500 GAL

BE EXACT ... PIN-POINT WHERE IT IS IN THIS SPACE TELL WHAT IS WRONG AND WHAT SHOULD BE DONE ABOUT IT'. PARA. FIGURE TABLE PAGE NO. NO. GRAPH NO.

)E OR TITLE, AND TELEPHO

RE:

DA

FOR I JUL 79

'4 2028-2

PREVIOUS EDITIONS ARE OBSOLERE.

P.S,--4F YOUR OUTFIT WANTS TO KNOW ABOUT YOUR RECOMMENDATION MAKE A CARBON COPY OF THIS AND GIVE IT TO YOUR HEADQUARTERS.

CIA@FO-T,l -@-C28-2 A@,ISMO OP-103-8@

FOLD BACK -

0 z C) m m 0

DEPARTMENT OF THE ARMY NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATESI 0 z m

OFFICAL BUSINESS

BUSINESS REPLY MAIL

FIRST CLASS BRM PERMIT NO. 82 ROCK ISLAND, IL POSTAGE WILL BE PAID BY ROCK ISLAND ARSENAL on

Director Armament and Chemical Acquisition and Logistics Activity ATTN: AMSTA-AC-NML Rock Island, IL 61201-9948

THE METRIC SYSTEM AND EQUIVALENTS

LINEAR MEASURE 1 Centimeter = 10 Millimeters = 0.01 Meters = 0.3937 Inches 1 Meter = 100 Centimeters = 1,000 Millimeters = 39.37 Inches 1IKilometer = 1,000 Meters = 0.621 Miles WEIGHTS 1 Gram = 0.001 Kilograms = 1,000 Milligrams = 0.035 Ounces 1 Kilogram = 1,000 Grams = 2.2 Lb 1 Metric Ton = 1,000 Kilograms = 1 Megagram = 1.1 Short Tons LIQUID MEASURE 1 Milliliter = 0.001 Liters = 0.0338 Fluid Ounces 1 Lilter = 1,000 Millimeters = 33.82 Fluid Ounces APPROXIMATE TO CHANGE Inches ............................ Feet .............................. Yards ............................. Miles ............................. Square Inches .................... ...... Square Feet ................ Square Yards ..................... Square Miles ...................... Acres ............................. Cubic Feet ........................ Cubic Yards ....................... Fluid Ounces ...................... Pints .............................. Quarts ............................ Gallons ........................... Ounces ........................... Pounds ........................... Short Tons ........................ Pound-Feet ....................... Pounds Per Square Inch ........... Miles Per Gallon ................... Miles Per Hour .................... TO CHANGE Centimeters ....................... Meters ............................ Meters ............................ Kilometers ........................ Square Centimeters ............... Square Meters .................... Square Meters .................... Square Kilometers ................. Square Hectometers .............. Cubic Maters ...................... Cubic Meters ...................... Milliliters .......................... Liters ............................. Liters ............................. Liters ............................. Grams ............................ Kilograms ......................... Metric Tons ....................... Newton-Meters .................... Kilopascals ........................ Kilometers Per Liter ............... Kilometers Per Hour ............... SQUARE MEASURE 0.155 Sq Inches 1 Sq Centimeter = 100 Sq Millimeters 10.76 Sq Feet 1 Sq Meter = 10,000 Sq Centimeters 1 Sq Kilometer = 1,000,000 Sq Meters = 0.386 Sq Miles CUBIC MEASURE 0.06 Cu Inches 1 Cu Centimeter= 1,000 Cu Millimeters 35.31 Cu Feet 1 Cu Meter = 1,000,000 Cu Centimeters TEMPERATURE 5/9 (-F - 32) = -C 212 Fahrenheit is equivalent to 1000 Celsius 90 Fahrenheit is equivalent to 32.20 Celsius 32 Fahrenheit is equivalent to 0 Celsius 9/5 'C + 32 = *F MULNPLY BY 2.540 0.305 0.914 1.609 6.451 0.093 0.836 2.590 0.405 0.028 0.765 29.573 0.473 0.946 3.785 28.349 0.454 0.907 1.356 6.895 0.425 1.609 MULTIPLY BY 0.394 3.280 1.094 0.621 0.155 10.764 1.196 0.386 2.471 35.315 1.308 0.034 2.113 1.057 0.264 0.035 2.205 1.102 0.738 0.145 2.354 0.621

CONVERSION FACTORS TO Centimeters .................... Meters ......................... Meters ......................... Kilometers ..................... Square Centimeters ............ Square Meters ................. Square Meters ................. Square Kilometers .............. Square Hectometers ............ Cubic Meters ................... Cubic Meters ................... Milliliters ....................... Liters .......................... Liters .......................... Liters .......................... Grams ......................... Kilograms ...................... Metric Tons .................... Newton-Meters ................. Kilopascals ..................... Kilometers Per Liter ............ Kilometers Per Hour ............ TO Inches ......................... Feet ........................... Yards .......................... Miles ........................... Square inches .................. Square Feet .................... Square Yards .................. Square Miles ................... Acres .......................... Cubic Feet ..................... Cubic Yards .................... Fluid Ounces ................... Pints ........................... Ouarts ......................... Gallons ........................ Ounces ........................ Pounds ........................ Short Tons .................... Pound-Feet .................... Pounds Per Square Inch ........ Miles Per Gallon ................ Miles Per Hour .................

0 x m

0 m m I m

PIN:

077261-000