Investment Casting Data
Investment Casting Data
Investment Casting Data
FOUNDRY TECHNOLOGY
INVESTMENT CASTING
ZOLLERN Castings Technology The Process Tolerances and Surfaces VDG Specification P 695 VDG Specification P 690 Shaping Applications
3 4 6 8 9 14 22
INVESTMENT CASTING
2 3
In the field of castings technology, the ZOLLERN Company is not only one of the foremost names in Europe but also a highly respected exporter to some of the most important industrial notions in the world. After all, we have been making castings for around one hundred years. ZOLLERN helped to shape every stage in the development of the technology, from the production of simple cast iron at the end of the 19th century to the most modern technologies in use today. Our origins, however, go a lot further back. Prince Meinrad II of Hohenzollern founded the smelting plant which bore his name and consisting of a blast furnace and hammer mill as long ago as 1708. During the 280 years since
then, the original iron works at Laucherthal (near Sigmaringen) has developed into a Company employing 2000 people and operating on an international scale. Today, ZOLLERN concentrates primarily on producing castings by a variety of methods (investment, sand, shell, mould, Shaw, continuous and centrifugal); it also has forging and drawing facilities at its disposal. At the same time, ZOLLERN is also well known as a manufacturer and supplier of drive systems, handling equipment and machine components, with the result that the expertise obtained from all the industrial sectors which the Company supplies is utilised synergically to the advantage of customers for ZOLLERN castings.
THE PROCESS
Investment casting is taken to mean casting into singlepiece ceramic shell moulds, eliminating the mould (pattern) parting line and the imprecision and flash associated with it. The characteristic feature of Investment casting is that the pattern is melted away and thus lost. The process is described by the following detail production steps. Investment castings is a precision casting method which is growing steadily in international significance for reason of economy. The method is being used to produce larger and larger castings. Investment castings is also employed on an increasing scale for so-called super alloys which require ever more complex smelting processes. Due to the economic benefits it offers, increasing weight is being attached to investment casting in comparative value analyses. Its scope for optimum shaping is unmatched by any other casting method. Investment castings-oriented design frequently offers an answer to technical problems which would be either impossible or far more expensive to implement using any other method.
Surface quality
The casting are produced without any trace of flash, and with an excellent surface finish. In many cases-expect for producing the required seat dimensions there is no need for a follow-on machining process.
Piece weights
Generally speaking, the investment casting technique is used for small piece weights of between 1 g and 10 kg. Larger workpieces up to 150 kg are also possible.
Summary
The investment casting technique is characterized by Almost unlimited scope for the shaping of castings Hardly any restrictions in terms of materials A high degree of dimensional accuracy due to elimination of the mould parting line usually responsible for casting imprecision Facility for complex shaped inner contours due to the use of ceramic cores Low material allowance on surfaces to be machined A high standard of surface quality
Material selection
All castable materials can be processed using this method. Investment casting is particularly suitable for use with materials unsuited to machining.
INVESTMENT CASTING
1 Patternmaking
3 Immersion
4 Packing in sand
4 5
5 Shell mould
7 Firing
8 Casting
9 Casting ejection
10 Release
11 Machining
12 Inspection
1 For every casting, a wax pattern has to be produced. Pattern are manufactured using an injection moulding machine in metal moulds made of soft metal alloy, aluminium or using wax. 2 The Patter are glued either individually (in the case of large workpieces) or in groups forming clusters to a gating system (sprue, gates, feeder) which is also manufactured using wax. 3 up to 5 By repeated immersion of the patterns in a ceramic slurry followed by packing in sand, after drying and where necessary chemical hardening, the patterns are surrounded by a refractory ceramic cell between 6 and 10 mm thick.
6 and 7 After drying and curing of the mould material, the wax patterns are melted and the moulds fired at temperatures up to 1100 C. 8 Casting is carried out by pouring into the moulds while hot. As even the finest details of the mould are completely filled, a compact casting result is achieved. 9 up to 12 After cooling and knocking out of the filled moulds, the casting are separated, machined and subjected to a final inspection.
Using the investment casting method, economical dimensioning means ensuring that no tolerance is selected closer than necessary for the intended purpose. Dimensional tolerances, surface and machining allowances are generally laid down by the Technical Memorandum of the VDG (German Association of Foundry Specialists), P 690. The accuracy level D 1 is generally taken to be the free size tolerance for casting which demonstrate an average degree of complexity. Accuracy level D2 applies to casting dimensions within toleranced limits. Accuracy level D3 corresponds to the range of variation between different production batches and applies only to dimensions for largescale series which have been agreed with the producer. In order to achieve D3 tolerances, it is often necessary to correct or redress the tool by means of trail gating processes. For this reason, it can be more economical to adjust the counter-part when mating for tolerance to the actual dimension of the casting.
Angular tolerances
As the permissible misalignment can occur to either side, no signs are specified in the VDG Memorandum. The respective tolerance value of the table in mm per 100 mm applies to the shorter arm of the angle at the workpiece and must be rounded up to the next full tenth.
Machining allowances
For closer tolerances than those specified above, machining allowances are necessary. Table 2 provides guideline values for this. These must be added to or deducted from the respective limiting dimensions. The machining allowance in each individual case depends on the material used and the type of machining process, and therefore must be agreed separately with the producer.
Table 1: Tolerances for linearity, flatness, parallelism and line area shape*
Accuracy level Length of toleranced element up to 25 mm 25 to 50 mm over 50 mm
Permissible dimensional variation D1 D2 D3 0.15 mm 0.10 mm 0.10 mm 0.25 mm 0.20 mm 0.15 mm 0.6% 0.4% 0.3%
INVESTMENT CASTING
6 7
Table 2: Machining allowances depending on the type of machining (all values in mm)
Greatest nominal dimension over 50 80 120 220 500 up to 50 80 120 220 500 Allowance per surface coarse 0.5 fine
N 4 N 5 N 6
N 7 N 8 N 9 N 10 N 11 N 12
Sure characteristics
The surfaces are free of scoring and comply with two surface categories/classes N7 to N9 according to table 3. Unless otherwise agreed, N9 in a sand-blasted surface finish is supplied as standard (see VDG Memorandum point 5).
Ra, Rz and Rt are approximated values Formation of relationship between Ra, Rz and Rt is not permissible.
2. Quality grades
2.1 Allocation of quality grades The allocation of external quality grades is determined in accordance with tests based on the magnetic leakage-flux method or dye method. The allocation of internal quality grades is determined by a radiographic test and/or X-ray examination. Extract from the guideline drawn up by the Investment Castings Committee of the VDG (Association of German Foundrymen).
INVESTMENT CASTING
8 9
2. Purpose
2.1 This technical memorandum defines dimensional tolerances, specifies machining allowances and surface roughness corresponding to the start of the art in the field of investment casting. It serves as a basis for optimum economic cooperation between investment casting suppliers and buyers. 2.2 The specifications mentioned here refer to sandblasted preserved or pickled surfaces in their delivered condition. Exception must be agreed where work processes are involved which alter the dimensional tolerances. 2.3 Unless otherwise agreed, initial samples are supplied for first-time orders. These are used to permit concrete mutual agreement between supplier and purchaser. Initial samples must be appraised by the buyer, followed by a written release to the foundry for series production. Deviation acknowledged by the release or with positive appraisal of the initial samples are binding for the production process and must be entered into the (casting) drawing.
3. Dimensional accuracy
3.1 Contraction and shrinkage During the solidification and cooling of cast metals, a contraction of the volume naturally occurs as a result of shrinkage. Other factors influencing the production of instrument castings can result from the shrinkage of the lost pattern and the expansion of moulds during heating. The sum of these influencing factors is taken into consideration in the shrinkage allowance during the manufacture of injection moulds. The shrinkage allowance is based on experience values, depending on the contour of the casting, the ceramic shell and the casting materials, as well as the casting techniques used in the individual foundries.
Fig. 1 The primary reference plane A is fixed by three reference points A1, A2 and A3. These should represent the largest surface area of the casting. The secondary reference plane B is fixed by two reference points B1 and B2, which should be arranged along the longitudinal axis. The tertiary reference plane C has only a single reference point C!, which should lie at or near the centre of the casting. Fig. 2 The reference planes are laid through the symmetrical axis of the casting.
A3 B2 C1
A2 B1
3.2 Reference planes and reference points Drawing used in the manufacture of casting must be gauged systematically using reference or locating points in order to ensure that dimensional checks and subsequent machining are in agreement. Reference points must be determined right from the early design stage and coordinated between the zero position of the reference planes is precisely defined by means of the reference point dimensions. All reference points must be arranged in such a way that they are not removed or altered during the subsequent machining process. Reference points should be positioned on the outside surfaces of the investment casting. They may take the form of raised or reference points are beneficial when dealing with castings with restricted shape and position tolerances. When determining the reference points, attention should be paid to ensuring that they do not fall in the area of a sprue. In case of complex shaping, it is possible in this way to position the casting precisely by (pre-) machining the locating points.
3.3 Overdefinition According to DIN 406, overdefinition must be avoided. Wall thicknesses must always be specified. 3.4 Mould and draught angles Mould and draught angles are not necessary as a general rule. Exceptions to this for reason of mouldmaking or casting necessity must be agreed between the investment casting supplier and the buyer.
INVESTMENT CASTING
4. Dimensional tolerances
4.1 Linear dimensional tolerances Achievable dimensional tolerances on investment casting are dependent on the following factors: Casting material Dimensions and shape of the casting Validity of the accuracy grade
4.1.2. Dimensions and shape of the casting The achievable accuracy level of the rated dimensions of an investment casting depends on the greatest dimension and the shape of the casting. If the rated dimension (GTA) exceeds the rated dimension range indicated for a certain accuracy level, the overall tolerance of the casting must be toleranced at the accuracy level (greatest tolerance field). Deviation outside the accuracy level must be agreed between the supplier and the buyer.
D2 GTA Zone 0.2 0.22 13.5 0.34 0.4 0.62 14.5 0.74 0.88 15 1.3 1.9 15 1.6 14.5 14 0.28 0.34 0.5 0.6 0.7 1.0 1.5
D3 GTA Zone 0.3 0.36 13 0.44 0.52 0.8 13.5 0.9 1.1 14 14.5 2.6 2.8 1.6
A1 GTA Zone 0.24 0.28 14 0.34 0.40 0.62 14.5 0.74 0.88 1.3 15 1.9 1.5 2.2 15.5 2.4 2.6 3.4 4.0 4.6
A2 GTA Zone 0.2 0.22 13.5 0.28 0.34 0.5 14 0.6 0.7 1.0 14.5 1.2 1.6 15 1.7 1.9
A3 GTA
10 11
13
13.5
14
14.5
15.5
5.6 6.6
4.1.1 Casting material In production, the varying characteristics of the materials affect the spread of the tolerance fields. For this reason, different rows of tolerance apply in table 1 to the different material groupings: Degree of accuracy Material group D Iron, nickel, cobalt and copper-based alloys Material group A Aluminium and magnesium-based alloys D1 to D3
4.1.3 Validity of the accuracy level In each of the material grouping D and A, there are three accuracy levels specified. Accuracy level 1 applies for all untoleranced dimensions. Accuracy level 2 applies for all toleranced dimensions. Accuracy level 3 can only be adhered to for individual dimensions and must be agreed with supplier, as for other additional production steps elaborate tool corrections are also necessary.
A1 to A3
4.1.4 Location of the tolerance zone The location of the tolerance zone relative to the nominal size can be freely selected. It is advisable to lay the tolerance zone evenly about the nominal size. In the case of surfaces which are to be machined, the sum / difference of the tolerance zone and machining allowance must be taken into account (see point 6).
4.2 Dimensional tolerance for wall thicknesses The wall thickness tolerance depend on the size of the (ceramic) walls of the mould their uninterrupted surface area their possible thermal distortion the metalostatic pressure of the molten metal. The wall thickness tolerance are, for this reason, not dependent on the level of accuracy. They are restricted (or reduced) by thicker edge sections, break-throughs (openings, holes), webs to be included in the casting, ribs and similar, which serve to relieve the wall thickness. The tolerance range in question in each case is indicated in Table 2.
This contains information an the smallest lateral length of a surface, which is authoritative in determining the wall thickness tolerance, for each material grouping.
b c a Wall thickness s a c
4.3 Shape and position tolerances Shape and position tolerances presume the determination of reference planes and reference points as defined by DIN ISO 1101. They are dependent on the material and shape of the casting and must therefore be agreed between the supplier and buyer. 4.4 Angular tolerances for material groups D and A Angular tolerance deviating from table 3 must be agreed with the supplier and entered in the drawing I accordance with DIN ISO 1101.
Case A
Case B
Case A The surface formed by the dimension a and b is not interrupted. Dimension b determines the wall thickness tolerance. Case B The surface formed by the dimensions a and b is interrupted by a borehole in the centre. The non-interrupted surface in this case is therefore formed by the dimensions b and c. The dimension c is smaller than b, and therefore c determines the wall thickness tolerance.
over 200 mm
30 2 30 2 20 2
30 2 20 2 15 2
30 2 15 2 10 2
20 2 15 2 10 2
For the range of nominal sizes, the length of the short arm is authoritative. The angle may deviate in both directions.
4.5 Dimensional tolerances for cast-on or cast-in prefabricated parts These must be determined in agreement with the foundry.
INVESTMENT CASTING
5. Surface properties
For cast surface, Ra (CLA) should be used in according with Table 4. Classes N 7, N 8 and surface treatments must be agreed separately and entered into drawing in accordance with DIN ISO 1302. Unless otherwise agreed, class N9 with sandblasted finish is assumed to be the condition on delivery.
d (mm) 2 up to 4 > 4 up to 6
6. Machining allowances
For sizes of fit on surface or low surface roughness factors which cannot be achieved by investment casting alone, machining allowance must take into account materialspecific properties and the computational unfavorable position within the tolerance field.
> 6 up to 10 > 10
12 13
7.2 Outside radii and outside chamfers Investment castings have no sharp edges with R = 0. For this reason, outside radii and outside chamfers should always be specified as maximum radii, for example R 0.5.
SHAPING
Despite the wide scope open to designers in the manufacture of investment cast components, it is advisable for considerations of economy to observe certain basic rules to keep the production input as low as possible. As a result, on the one hand the basic law of physics are obeyed during the casting process and work sequence from the tool to the finished casting, while on the other hand they indicate the scope of achievements possible using the investment casting process. In either event, a basic rule of thumb applies: The more complex the shape of a workpiece, the more difficult it is to process, the more economical it is to produce it by investment casting. Investment cast items are often cast ready for installation without further processing. Where this is not possible due to insufficient tolerances, conventional machining methods can be used. Far-thinking, sensible design simplifies the machining process, so reducing the input and improving economy.
Water-soluble cores
For inside contours which are not too narrow, water-soluble cores are used . These each involve the manufacture of another tool and coated with the non-water soluble pattern material. When the core is dissolved after immersion in a water bath, the required inside contour is left.
INVESTMENT CASTING
Ceramic cores
Ceramic cores are used for narrow or intricately shaped cavities in the casing involving undercuts which cannot be reached or properly filled out by the ceramic mould material during the mouldmaking process. They are inserted in the tool ready fired and, in contrast to water-soluble cores, remain in the mould until after casting.
Assembled pattern
In certain cases, it is possible to assemble patterns. With the aid of fitting marks, they are precisely assembled and connected, so forming the undercut contours . This procedure is often used in cases where symmetrical patterns can be assembled from two or more identical pattern components, as then only a single (part) tool is required.
14 15
Bulkiness
By providing recesses (=farsighted design for casting), it is possible to reduce the number of gates; this makes the tools less bulky and reduces the complexity of the casting process.
Favourable Gate
Core
Curved channels
A feature which can be produced particularly economically are curved channels, which are shaped in such a way that they can be manufactured in the tool using core sliders. In other cases, watersoluble or ceramic cores must be used, which involve the manufacture ofa special tool.
Toothing
The rough and finish casting of special toothing arrangements of all different types can be economically performed using the investment casting technique, in particular using heavy-duty, non-machinable materials. Applications include Gear and clutch toothing, serration, internal gears and gear-type profiles which cannot be machined using the generation grinding method, bevel and chain wheels, worm gear wheels. If the investment casting tolerances are not sufficient for the pitch and diameter, the casting must be subsequently machined, for example by grinding.
Threads
Threads are only included in the casting if the investment casting tolerances are sufficient for the pitch and profile. This means that only the following special cases can be considered for casting : Interrupted threads, e.g. for bayonet catches and quickaction couplings; Threads which mate with materials such as rubber or plastic Coarse circular or trapezoidal threads; Threads of alloy which are important to examine whether it might not be possible to either avoid their use by a modification of the design, or to carry out subsequent grinding.
The modules for which casting is still possible depend on the size of the casting and the type of material. The following general rule applies: m 1.0 mm for FE, I, Co based alloys, m 0.5 mm for Al and Cu based alloys. In the case of serration and similar types of toothing, the teeth which become finer towards the middle should be recessed at the places at which the pitch falls below the following values: t = 1.0 mm with Fe, Ni, Co based alloys t = 0.5 mm for Al and Cu based alloys
Cooling fins
Cooling fins should have cross-sections wich taper towards the outside; this not only improves casting performance but also the heat flow.
Material: Al or Cu based alloy Possible Favourable R Favourable
Heating edges
R R
R R
INVESTMENT CASTING
l~4 x h R
t h R R R
16 17
Unfavourable
Favourable
R Heating edge R
R R
R R
Favourable
Shrinkage cavities
Shrinkage cavities are a natural occurrence on the solidification of molten metal. The task of the producer is to use suitable means to make them occur not in the casting itself but in the gates, which are parted off after casting. For reason of cost, it can happen that the designer tolerates certain defined shrinkage cavities either because they occur at an uncritical location or because they will in any case be removed by a subsequent machining process. However, this must be agreed expressly with the producer. The ideal casting is shaped in such a way that its crosssections diminish as they progress from the gate towards more distant sections of the casting; If this ideal constellation is achieved, the solidification process can take place in the opposite direction to the gate. Castings which come closest to this ideal are those with walls of approximately equal thickness and those which offer the producer the possibility to gate them for optimum casting. The resulting points to observe when setting about the design of an optimum investment casting are illustrated in the following.
Gate Shrinkage cavity
Parting cut
Molten
Casting
Junctions
Junctions should be configured so that no sharp internal edges or accumulations of material occur. For this reason, sloping and parallel walls should be joined to each other wherever possible at right angels.
Unfavourable
Better
Favourable
Gates
Where possible, a suitable even outer surface at the thickest cross-section should be selected for the gates. This constellation will permit them to be separated off more economically later. The gating surfaces can serve as gauge or reference points for subsequent machining.
Possible
Favourable Gate
Gate 1
INVESTMENT CASTING
Holes and channels dia. / or similar d (mm) 2 up to 4 > 4 up to 6 > 6 up to 10 > 10 Greatest length or depth Through hole Blind hole l t 1xd 2xd 3xd 4xd 0.6 x d 1.0 x d 1.6 x d 2.0 x d Width b (mm) 2 up to 4 > 4 up to 6 > 6 up to 10 > 10
Slots and groves Greatest depth, bottom open closed l t 1xb 1.0 x b 2xb 3xb 4xb 1.6 x b 2.0 x b
18 19
Through holes
It is advisable to configure through holes and slots in such a way that they can be formed with an unsplit core slide.
Slots
Slots can only be produced without ceramic cores if the ratio b:t or b:l as indicated in the diagram on the right can be adhered to; The dimension S can be selected as required.
b t b t
Favourable
d (b) R
d (b)
d (b)
d (b)
d (b)
d (b)
Blind holes
Blind holes and closed slots must be rounded off at the bottom. In the case of Al and Ti alloys, it is advisable to avoid blind holes.
To be avoided Favourable
d (b) t
d (b)
d (b)
d (b)
Flat surfaces
Although it is possible to cast relatively large surfaces, these should be avoided where possible, as they can only be executed with a dis-proportionate effort. They should consequently be broken up by ribbing effects, recessing or breakthroughs. This simplifies the casting process, increases the form strength of the casting under certain circumstances, and often also reduces the weight.
Unfavourable Favourable
P P P
P P P
Possible
Core
Unfavourable
To be avoided
Favourable
Ideal
Machining allowance 3 mm
INVESTMENT CASTING
Investment casting are frequently ready-to-mount components without need for subsequent machining. However, where extremely narrow tolerances make this impossible, components may require a machining cycle. Intelligent design can simplify the machining process, so improving overall economy.
Inscription
Cast company loges, spare part numbers, detents, position and flow marks as well as any other identifying symbols save assembly and downtimes, and help to avoid mistakes when exchanging and ordering spare parts. The type of lettering or identifying mark depends financially on the type of material used: recessed when using soft metals, raised for aluminum or steel tools. If a raised inscription is not possible for functional reason, the inscription field must be recessed and the inscription itself raised. Also for reasons of economy, the lettering should be positioned parallel to the division plane of tool where possible. In case of doubt, a remark in the (enquiry) drawing indicating the possible positions for the
Undercuts
Undercuts can be arranged in such a way that they eliminate the need for water-soluble or ceramic cores. The knock-out direction in the pattern tool must be taken into consideration here: As the illustration indicates, the undercut determines the knock-out direction.
Peripheral undercuts
Possible (with core) Possible (without core)
Straight undercuts
20 21
= Knock-out-direction
Recesses
Where the functional characteristics of the component so permit, surface which will require subsequent machining can be recessed from the initial casting stage, so reducing the degree of stock removal (and also the workpiece weight).
Possible Favourable
inscription field is sufficient. For the nominal height of the lettering, the following regulation applies: h 22.5 mm for Fe, Ni, Co based alloys h 2.0 mm for Al and Cu based alloys.
Recessed lettering
Raised lettering
Possible
Favourable
Recessed lettering
Raised lettering
APPLICATIONS
Material types
The investment casting technique permits the use of an almost unlimited spectrum of casting and also wrought materials. A certain restriction is imposed by the fact that a large number of materials possess similar characteristics and be substituted by alternative materials which are at least equivalent in value. On the other hand, investment casting also permits the use of a higher-grade material at no additional cost, so covering a wide range of possible applications. Accordingly, in the following explanation, types providing a representative selection have been specified under the various material groupings. If the use of different materials is stipulated expressly for certain applications, an enquiry is necessary with the producer. The data contained in the tables are guideline values only. This applies also where guaranteed minimum values are specified in standards or other regulations. As a rule, these regulations refer to other shaping techniques unless they explicitly specify the instrument casting method. Unless otherwise indicated, the values apply to separately cast test bars.
INVESTMENT CASTING
Economy
It makes economic sense to work with customarily used investment casting materials. Particular reference is made to these in the following tables. In case of doubt, consult the producer. If at all possible to use corrosion-resistant materials, in particular for small components, in order to eliminate the need for costly surface finishing which is necessary when working with low-alloy and non-alloyed materials. This type of component remains chemically resistant even if the surface is damage. It id frequently possible to procure the same components made of different materials- even alloys on a different basis with one and the same pattern tool. This permits, for example, the material used for identical fittings and pump components to be varied to match the aggressive properties of different media. However, this simple exchange of materials also makes sense in cases where greater levels of different media. However, this simple exchange of materials also makes sense in cases where greater levels of strain occur than were previously known or envisaged. In this case, it is almost always possible to select a more suitable material.
22 23
1 Nozzle tips for hot runner injection nozzles used in the plastics industy Material Inconel 713 2 End piece for the steering column of the Fokker F100 Material GF-AlSiMg 0.6 wa Material number 3.2384 Verification of mechanicaltechnological characteristics is provided through trails from the casting. 3 VDO housing Electronic housing for LCD screen used in an armoured defence helicopter PAH2. The part is finish machined. Wall thickness partially to 1.2 mm. Modular system with over 90 movable components. Material G-AlSiMg 0.6 wa. 4 Hand lever Material G-AlSi7Mg 0.6 wa Material number 3.2384 Door opening in the Airbus A330/A 340. 7
5 Bone clamps made of implant material ZOLLERN SUPER N CoCrMoN 6 Steering column lever Material G-AlSi7Mg 0.6 wa Material number 3.2384 Weight 1350 g Foot of the steering column for transmission of mechanical forces in the Do 328
7 Fixed and steering wings for missiles made of material 17/4 PH Material number 1.4549
8 Door fitting, internal Material G-AlSi7Mg 0.6 wa Material number 3.2384 Emergency exit in the Airbus 9 Vacuum castings made of the materials Inconel 713, Inconel 718 and Hastelloy for apparatus construction
The plant operates in the high vacuum range from 10-2 to 10 m bar, and is capable of producing component sizes of up to appr. 250 mm in diameter and a maximum of 300 mm in height. The following maximum melting weights can be cast: 15 kg of Ni-based material 15 kg of Co-based material 15 kg of steel alloys 15 kg of Cu-based material The vacuum casting technique additionally offers the benefit of an extremely high degree of purity. Due to the special process technology used, it is also possible to achieved specific grain refinement of castings. The work sequence at the smelting stations is fully automated with the exception of loading and unloading. Vacuum remelt alloys exclusively are used as base materials for superalloys.
INVESTMENT CASTING
10
10 Aluminum electronic housing for an optical application in the field of laser technology. Material FG-AlSiMg 0.6 wa Material number 3.2384 Weight 120 g The complex internal contour is achieved using various watersoluble wax cores.
13 Mounting casting for the epicyclic gearbox in the gear system/ starter stage of a jet engine Material 17/4 pH 1.4549 Weight approx. 1500 g Rm. approx. 1200 Mpa 24 25
11
11 Cut-away model demonstrating the structural principle of the exhaust gas turbocharger The turbine wheel (hot side) in the foreground and behind it the compressor area (cold side) with aluminium impeller wheel 12 Aluminium compressor impeller for an exhaust gas turbocharger Material number 3.2384 Strength values Rp 0.2 270 N/mm2 Rm 330 N/mm2, A5 3%
12
13
Switzerland plant Sntisstrasse 11 CH-9401 Rorschach ZOLLERNTel. +41 71 844 16 88 MIMTEC AG Fax +41 71 844 16 77 eMail [email protected] www.mimtec.com
Foundry Technology Rua Jorge Ferreirinha, 1095 Apartado 1027 P-4470-314 Vermoim MAIA Tel. +351 22 94 14 68 1 Fax +351 22 94 14 69 5 eMail [email protected]
P. O. Box 233 SE-73224 Arboga Tel. +46 58 91 60 35 Fax +46 58 91 20 02 eMail [email protected] www.kvalitetsstal.se
No. 33, 7th Avenue TEDA-TIANJIN 300 457 Peoples Republic of CHINA Tel. +86 22 25 32 38 11 Fax +86 22 25 32 38 10 eMail [email protected]
USA plant
9364 Wallisville Rd., Suite 150 Houston, Texas 77013 ZOLLERN USA North America L.P. Tel. +1 71 36 73 79 02 Fax +1 71 36 73 79 50 eMail [email protected]
Drive Technology Gears Httenstrae 1 D-46284 Dorsten Tel. +49 23 62 67 0 Fax +49 23 62 67 40 3 eMail [email protected]
Braunschweig plant
Drive Technology Plain Bearings ZOLLERN BHW Gleitlager Postfach 32 13 GmbH & Co. KG D-38022 Braunschweig Tel. +49 53 12 60 50 Fax +49 53 12 60 52 22 eMail [email protected]
Sales offices
France ZOLLERN S..r.l 13, Rue Allwies F-57200 Sarreguemines Tel. +33 3 87 95 35 14 Fax +33 3 87 95 35 21 ZOLLERN Italiana S.r.L. Via C. Battisti, 1 I-21045 Gazzada (VA) Tel. +39 03 32 46 20 59 Fax +39 03 32 46 20 67
Osterode plant
Drive Technology Plain Bearings ZOLLERN BHW Gleitlager Rolandsweg 16 20 GmbH & Co. KG D-37520 Osterode am Harz Tel. +49 55 22 31 27 0 Fax +49 55 22 31 27 99
Italy
Drive Technology Plain Bearings Av. Manoel Incio Peixoto, 2147 BR-36771-000 Cataguases MG Tel. +55 32 34 29 20 02 Fax +55 32 34 29 20 26 eMail [email protected]
Great Britain
Zollern UK Limited Castle Hill Kenilworth GB-CV8 1NB Tel. +44 19 26 51 54 20 Fax +44 19 26 85 34 11
Aulendorf plant
Mechanical Engineering Components Postfach 12 65 ZOLLERN GmbH & Co. KG D-88322 Aulendorf Tel. +49 75 25 94 81 30 Fax +49 75 25 94 81 00 eMail [email protected]
Netherlands
ZOLLERN Nederland B.V. Postbus 134 NL-5150 AC DRUNEN Tel. +31 41 63 22 92 0 eMail [email protected] Fax +31 41 63 20 93 6 www.zollern.nl
INVESTMENT CASTING
CONTACT
26 27
ZOLLERN GmbH & Co. KG
Foundry Technology Postfach 12 20 D-72481 Sigmaringen Tel. +49 75 71 70 44 0 Fax +49 75 71 70 60 1 eMail [email protected]
Laucherthal plant
We offer comprehensive project management: Many years of project experience CAD masters Project meetings on-site and plant inspections Detailed, binding offers
ZOLLERN GmbH & Co. KG Postfach 12 20 D-72481 Sigmaringen Tel. +49 75 71/70-0 Fax +49 75 71/70-601 [email protected] www.zollern.com
Z487 04.2005
www.revoLUZion.de