Azida de Sodiu

Download as doc, pdf, or txt
Download as doc, pdf, or txt
You are on page 1of 2

Sodium Azide

FACT SHEET #3 July 2010 REVISION: SECOND

NORTHEASTERN UNIVERSITY PROCEDURE FOR THE SAFE HANDLING AND USE AND MANAGEMENT OF SODIUM AZIDE INTRODUCTION Sodium Azide, NaN3, mol wt 65.02, CAS Number 26628-22-8, is a colorless, odorless, crystalline solid (salt-like) or solution. It is soluble in water or liquid ammonia, slightly soluble in alcohols, and insoluble in ether. It is highly toxic and presents a severe explosion risk when shocked or heated. When heated from 275 to 330C in dry air, the solid crystals decompose with the evolution of nitrogen gas, leaving a residue of sodium oxide. Sodium hydroxide then forms in moist air. Synonyms and Trade Names are Azide, Azium, and Sodium salt of hydrazoic acid. PROPERTIES Sodium azide is a common preservative of samples and stock solutions in laboratories and a useful reagent in synthetic work. It is not explosive except when heated near its decomposition temperature (300C) or reacted with metals; heating sodium azide should be avoided. Sodium azide (solid or concentrated solution) should never be flushed down the drain since this practice can cause serious incidents when the azide reacts with lead or copper in the drain lines and explodes. Sodium azide has high acute toxicity as well as high toxicity to bacteria in water treatment plants. Note that metal shelves and other metal items used to handle sodium azide (i.e., spatulas) can also result in the formation of heavy metal azides and thus should be avoided. Solutions of sodium azide do not pose the danger of shock-sensitivity associated with the solid form; however, the hydrazoic acid generated when the sodium azide is dissolved is extremely toxic. Therefore, the solution is should prepared inside a laboratory chemical hood. If not dissolved, solid sodium azide should be stored in a secured cabinet because of the shock hazardous. HAZARDS Sodium azide is on the Hazardous Substance List because it is cited by ACGIH, DOT, NIOSH, HHAG, DEP, and EPA (see Laboratory Chemical Hygiene Plan section 5 for glossary of terms). This substance also is on the Special Health Hazard Substance List because it is a mutagen. Mutagens may have a cancer risk. All contact with this substance should be reduced to the lowest possible level. Sodium azide and hydrazoic acid (HN3, which is formed from NaN3 in water) are known to produce hypotension (low blood pressure) in laboratory animals and humans, and to form strong complexes with hemoglobin, and consequently block oxygen transport in the blood. Acute inhalation of HN3 vapor by humans results in lowered blood pressure, bronchitis, eye, nose, throat, and lung irritation, headache, weakness, and collapse. A skin designation has been assigned to the OSHA PEL due to the ability of NaN3 to readily penetrate intact skin, and any dermal exposure can significantly contribute to the overall exposure to sodium azide.

Target organs are eyes, skin, lungs, central nervous system, cardiovascular system and kidneys. Use appropriate ventilation (laboratory chemical hood) and personal protective equipment (such as gloves) to minimize potential exposure. WORKPLACE EXPOSURE LIMITS NIOSH: The recommended airborne exposure limit is 0.11 ppm as hydrazoic acid or 0.3 mg/m3 as sodium azide, which should not be exceeded at any time. ACGIH: The recommended airborne exposure limit is 0.11 ppm as hydrazoic acid or 0.29 mg/m3 as sodium azide (0.1 ppm Ceiling, Skin), which should not be exceeded at any time. The above exposure limits are for air levels only. When skin contact also occurs, you may be overexposed, even though air levels are less than the limits listed above. HANDLING AND STORAGE Prior to working with sodium azide you should be trained on its proper handling and storage. Use appropriate personal protective equipment such as safety glasses, goggles, gloves, and laboratory coat when handling sodium azide. On contact with water, sodium azide forms hydrazoic acid which is toxic. Sodium azide reacts with heavy metals (such as silver, gold, lead, copper, brass, or solder in plumbing systems); and metal salts to form an accumulation of the highly explosive compounds such as lead azide and copper azide. Sodium azide is not compatible with chromyl chloride, hydrazine; bromine; carbon disulfide; dimethyl sulfate; and dibromomalonitrile; strong acids (such as hydrochloric, sulfuric and nitric); and acid chlorides. A danger of explosion exists from friction, heat or shock. Store in tightly closed containers in a secured, cool, and well-ventilated area away from water. http://www.ehs.neu.edu/hazardous_waste/fact_sheets/sodium_azide/

You might also like