Scribd
Upload
2K views3 pages

LED Temperature Thermometer Project

This document summarizes an LED temperature thermometer project that uses an LM34 temperature sensor and LM3914 LED driver chip to display room temperature via a bar graph of 10 LEDs, with each LED representing a 2 degree Fahrenheit temperature range. The LM34 sensor produces a voltage output proportional to the measured temperature, which is fed to the LM3914 chip. The LM3914 compares the sensor voltage to internal reference voltages to determine which LEDs to illuminate, displaying the current temperature. The document provides details on calibrating the LM3914 reference voltages and sensor gain to accurately map temperatures to the LED display.

Uploaded by

bhk_bdbhatt4424
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
2K views3 pages

LED Temperature Thermometer Project

This document summarizes an LED temperature thermometer project that uses an LM34 temperature sensor and LM3914 LED driver chip to display room temperature via a bar graph of 10 LEDs, with each LED representing a 2 degree Fahrenheit temperature range. The LM34 sensor produces a voltage output proportional to the measured temperature, which is fed to the LM3914 chip. The LM3914 compares the sensor voltage to internal reference voltages to determine which LEDs to illuminate, displaying the current temperature. The document provides details on calibrating the LM3914 reference voltages and sensor gain to accurately map temperatures to the LED display.

Uploaded by

bhk_bdbhatt4424
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

LED Temperature Thermometer Project

Introduction To LED Temperature Thermometer This LED temperature thermometer project will display the room temperature where it is placed using 10 LEDs, with eachLED representing 2 degree Fahrenheit step, forming a bargraph display. Electronics hobbyists will learn how to use thetemperature sensor and LM3914 LED driver. Another method of doing this project is using a low cost microcontroller if one is familiar with it. Otherwise, this is a good project for beginners to electronics. The LM3914 is a monolithic integrated circuit that senses analog voltage levels and drives 10 LEDs, providing a linear analog display. Current drive to the LEDs is regulated and programmable, eliminating the need for resistors. Much of the display flexibility derives from the fact that all outputs are individual, DC regulated currents. Various effects can be achieved by modulating these currents. The individual outputs can drive a transistor as well as a LED at the same time, so controller functions including "staging" control can be performed. The LM3914 can also act as a programmer, or sequencer. Temperature Thermometer Circuit Description

The schematic diagram shows how temperature sensor LM34DZ is connected to LM3914 IC. It produces a voltage between VCC and Ground that is linearly proportional to the temperature that it senses, usually 10mV/degree F. In this circuit,it is connected to R1, R2 and R3 to form a gain output of 40mV/degree F. The output of LM34 is fed to LM3914 pin 5. LM3914 has 10 internal comparators with outputs connected to LED1-LED10. Theinput is compared to the voltages at pins 4 and 6 which will determine which LEDs are lighted up. Pin 6 must be calibratedto a voltage of 3.345V and pin 4 2.545V in order to display the range of temperature mentioned by adjusting variableresistors R5 and R7. Start by adjusting R7 to obtain pin 6 calibration voltage and then R5 to obtain pin 4 calibration voltage. Use a standard thermometer and measure the air temperature at the vicinity of LM34. Adjust variable resistor R1 so thatthe proper LED for that temperature are lighted up. Next, measure the voltage between pin 5 and GND. Its value should beclose to the calculated equation below: V=0.225 + (0.04 X T) where T is the temperature in degrees Fahrenheit.

Make sure that LM34 is position away from any heat source of the circuitry as this will affect its reading. Adequate holesshould be drilled on the enclosure to ensure ventilation to the sensor. Temperature Thermometer Parts List

The specifications of the Temperature Thermometer LM34 and LM3914 Specscan be obtained from National Semiconductor website.

Source : Extracted from Popular Electronics July 1996, By William Sheets and Rudolf Graf.

You might also like