Nov 2008

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

Code No: R05310203

Set No. 1

III B.Tech I Semester Regular Examinations, November 2008 POWER SYSTEMS-II (Electrical & Electronic Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) Briey discuss the various types of conductor material used for over head transmission lines (b) A single phase, two wire transmission line 20km long, is made up of round conductors each 0.9cm in diameter, separated from each other by 45cm.Calculate the equivalent diameter of a ctitious hollow, thin-walled conductor having the same inductance as the original line. What is the value of this inductance? [8+8] 2. (a) Show how regulation and transmission eciency are determined for medium lines using end condenser method and illustrate your answer with suitable vector diagram. (b) A three phase transmission line is 135 km long. The series impedance is Z=0.04 + j 0.95 ohms per phase per km, and shunt admittance is Y=j 5.1106 mhos per phase per km. The sending end voltage is 132 kV, and the sending end current is 154 A at 0.9 power factor lagging. Determine the voltage, current and power at the receiving end and the voltage regulation using medium line-T model. [6+10] 3. (a) Explain the evaluation of transmission line constants. (b) A three - phase overhead transmission line has series impedance per phase of 250 800 ohms and a total shunt admittance of 0.0019 900 siemen per phase. The line delivers a load of 100MW at 0.8 pf lagging and 200kV between the lines. Calculate the sending-end voltage and current by the rigorous method. [6+10] 4. (a) Starting from rst principles show that surges behave as travelling wave. (b) An over head line with inductance and capacitance per km length of 1.24 mH and 0.087 F respectively is connected in series with an ungrounded cable having inductance and capacitance of 0.185 mH / km and 0.285 F / km respectively. Calculate the values of reected and refracted waves of voltage and current at the junction due to a voltage surge of 110 kV traveling to the junction i. along the line towards the cable, and ii. along the cable towards the line. [8+8]

5. (a) Explain the phenomenon of corona? How can the corona loss be minimized in transmission lines. 1 of 2

Code No: R05310203

Set No. 1

(b) Determine the disruptive critical voltage and the critical voltages for local and general corona on a 3-phase overhead transmission line, consisting of three stranded copper conductors, spaced 3 meters apart at the corners of an equilateral triangle. Air temperature and pressure are 21o C and 73.5 cm of mercury respectively. Conductor diameter is 2.2 cm. Take air density factor 3.92 b/(273 + t), irregularity factor (m) = 0.82 and surface factors (mv ) for local and general corona = 0.7 and 0.8 respectively. Break down strength of air is 21.21 kV (r.m.s) per cm. [6+10] 6. (a) Explain why the potential distribution is not, in general, uniform over the string in suspension type of insulators. (b) A string of suspension insulator consists of four units and the capacitance to ground is 12 percent of its mutual capacitance. Determine the voltage across each unit as a fraction of the operating voltage. Also determine the string eciency. [6+10] 7. (a) Explain the necessity of a stringing chart for a transmission line and show how such a chart can be constructed. (b) Two towers of height 40 and 90 meters respectively support a transmission line conductor at a water crossing. The horizontal distance between the towers is 500 m. If the allowable tension in the conductor is 1600kg, nd the minimum clearance of the conductor and the clearance of the conductor mid-way between the supports. Weight of the conductor is 1.1kg/m. Bases of the towers can be considered to be at the water level. [6+10] 8. (a) Derive the formula for insulation resistance of a cable. (b) Determine the economical core diameter of a single core cable working on 22 kV, single phase system. The maximum permissible stress in the dielectric is not to exceed 33 kV/cm. [8+8]

2 of 2

Code No: R05310203

Set No. 2

III B.Tech I Semester Regular Examinations, November 2008 POWER SYSTEMS-II (Electrical & Electronic Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) How can the inductance of a bundled conductor line be calculated? Derive expressions for geometric mean radii of duplex, triplex and quadruplex arrangement. (b) Calculate the inductance per phase of a three-phase, double circuit line as shown in Figure 1b. The diameter of each conductor is 1.5 cm. [8+8]

Figure 1b 2. (a) What do you understand by the terms nominal-T and nominal- circuits. (b) A 220 kV, 50 Hz, three-phase transmission line is 50 km long. The resistance per phase is 0.15 ohms/km and the inductance per phase is 1.33 mH per km and the shunt capacitance is negligible. Use the short line model to determine i. the voltage and power at the sending end, ii. voltage regulation and eciency when the line is supplying a three-phase load of 400 MVA, 220 kV at a power factor of 0.8 lagging. [6+10] 3. (a) Explain surge impedance loading. (b) A three-phase, 50 Hz, 160 km long transmission line has three conductors each of 0.75 cm radius spaced at the corners of triangle of sides 2.5 m, 3m and 3.5m. The resistance of each conductor is 0.3 ohms per km and the line delivers 30 MVA at 132 kV and at a lagging p.f. of 0.95. Determine ABCD constants as i. long line (both real and complex angle methods) and ii. Parameters of equivalent T representations of long lines. 4. (a) Explain the surge phenomena. [6+10]

1 of 2

Code No: R05310203

Set No. 2

(b) A voltage having a crest value of 3000 kV is traveling on a 750 kV line. The protective level is 1700 kV and the surge impedance of the line is 300. Calculate i. ii. iii. iv. the current in the line before reaching the arrester current through the arrester the value of arrester resistance for this condition reect voltage. Verify the reection and refraction coecient.

[6+10]

5. (a) Write a short notes on radio interference due to corona. (b) Determine the disruptive critical voltage and the visual critical voltages for local and general corona on a 3-phase overhead transmission line consisting of three stranded copper conductors spaced at 2.5 meters apart at the corners of an equilateral triangle. Air temperature and pressure are 210 C and 73.5 cm of Hg respectively. Conductor diameter is 1.8 cm, irregularity factor (m0 ) 0.85, and surface factors (mv ) is 0.7 for local and general corona are 0.7 and 0.8 respectively. Breakdown strength of air is 21.1 kV (r.m.s) / cm. [6+10] 6. (a) List the characteristics which the insulator should posses. (b) Each conductor of a 3-phase high voltage transmission line is suspended from cross arm of steel tower by a string of 4 suspension type disc insulators. If the voltage across the second unit is 13.2 kV and that across the third unit is 20 kV. Calculate the voltage between the conductors. [8+8] 7. (a) Show that the sag on level supported line conductor of span L, weight per unit length W kgs, and minimum tension in the line conductor T0 is given by; 2 s = wL0 . What will be the sag if level dierence is of h meters? 8T (b) An overhead line has the following data: span length 185 m, dierence in levels of supports 6.5 m, conductor diameter 1.82 cm, weight per unit length of conductor 1.5kg/m, wind pressure 39 kg/m2 of projected area. Maximum tensile strength of the conductor is 4250 kg/cm2 , factor of safety is 5. Calculate the length of the lower support. [8+8] 8. (a) Derive a formula for capacitance of a single core cable. (b) Determine the economical core diameter of a single core cable working on 210 kV, 3-phase system. The maximum permissible stress in the dielectric is not to exceed 230 kV/cm. [8+8]

2 of 2

Code No: R05310203

Set No. 3

III B.Tech I Semester Regular Examinations, November 2008 POWER SYSTEMS-II (Electrical & Electronic Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) Show that the inductance per loop meter of two wire transmission line using solid round conductors is given by L = 4 107 log D henries where D is the r distance between the conductors and r is the GMR of the conductors. (b) A single phase overhead line 32km long consists of two parallel conductors each 1cm diameter, 3 meters apart. If the line voltage be 25kV at 50Hz. Determine the charging current with the line open circuited. [8+8] 2. (a) What do you understand by medium transmission lines? How capacitance eects are taken into account in such lines? (b) A three phase transmission line is 140 km long. The resistance per phase is 0.04 ohms per km and the inductance per phase is 0.95 mH per km. The shunt capacitance is 0.0105 nF per km. The receiving end load is 90 MVA with 0.85 power factor lagging at 110 kV. Determine the voltage, powers at the sending end, voltage regulation and eciency by using nominal - model. [6+10] 3. (a) Starting from the rst principles, deduce expressions for ABCD constants of a long line in terms of its parameters. (b) A three-phase, 50 Hz, 150 km long transmission line has three conductors each of 0.7 cm radius spaced at the corners of triangle of sides 2 m, 3.5m and 4.5m. The resistance of each conductor is 0.4 ohms per km and the line delivers 50 MVA at 132 kV and at a lagging p.f. of 0.85. Determine ABCD constants as long line (both real and complex angle methods) [8+8] 4. (a) Develop an equivalent circuit for the analysis of the behavior of travelling waves at transition points on a transmission line. (b) The ends of two long transmission lines, A and C are connected by a cable B, km long. The surge impedances of A, B, C are 500, 70 and 600 ohms respectively. A rectangular voltage wave of 20 kV magnitude and of innite length is initiated in A and travels to C. Determine the rst and second voltages impressed on C. [8+8] 5. (a) Describe the phenomenon of corona? Discuss the factors which aect corona loss. (b) A 3-phase line has conductors of radius 1.0 cm, spaced at the corners of an equilateral triangle of side 2.5 m apart. If the dielectric strength of air is 30kV/cm, determine the disruptive critical voltage at which corona will occur. Take relative air density factor =0.96 and irregularity factor m0 = 0.94. [8+8] 1 of 2

Code No: R05310203

Set No. 3

6. (a) List the advantages of suspension type insulators over pin type insulators. (b) A string of 5 insulator units has a self-capacitance equal to 11 times the pin to earth capacitance. Find the string eciency? [6+10] 7. (a) Describe the vibration of power conductors and explain the methods used to damp out these vibrations. (b) Determine the sag of an overhead line for the following data: span length 160 meters, conductor diameter 0.95 cm, weight per unit length of the conductor 0.65 kg/meter. Ultimate stress 4250 kg/cm2 , wind pressure 40 kg/cm2 of projected area, Factor of safety 5. [6+10] 8. (a) Derive a relation between the conductor radius and inside sheath radius of a single core cable so that the electric stress of the conductor surface may be minimum. (b) A cable has been insulated with two insulating materials having permittivity of 6 and 4 respectively. The inner and outer diameter of a cable is 3 cms and 7 cms. If the dielectric stress is 50 kV/cm and 30 kV/cm, calculate the radial thickness of each insulating layer and the safe working voltage of the cable. [8+8]

2 of 2

Code No: R05310203

Set No. 4

III B.Tech I Semester Regular Examinations, November 2008 POWER SYSTEMS-II (Electrical & Electronic Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) Derive an expression for the inductance per phase for a 3-phase overhead transmission line when conductors are symmetrically placed. (b) Calculate the inductance per phase of a three-phase transmission line as shown in Figure 1b. The radius of the conductor is 0.5 cm. The lines are untransposed. [8+8]

Figure 1b 2. (a) Draw the phasor diagram for a nominal- circuit of a transmission line and derive expressions for sending end voltage and current. (b) A three-phase, 50Hz, 11kV transmission line delivers a load of 2400kW at power factor of 0.8 lag over a distance of 20km. The line conductors are placed at the corners of an equilateral triangle of 2m side. The line losses are 10%. Calculate the sending end power factor. [8+8] 3. (a) Starting from rst principles derive an expression for the sending end voltage and current of a long transmission line interms of the line parameters and receiving end voltage and current. (b) A three - phase overhead transmission line has series impedance per phase of 120 750 ohms and a total shunt admittance of 0.002 900 siemen per phase. The line delivers a load of 125MW at 0.85 pf lagging and 132kV between the lines. Calculate the sending-end voltage and current by the rigorous method. [8+8] 4. (a) What is the outcome of the transient in the transmission lines? Develop the dierential equation for the transient in the transmission system. (b) A 500 kV, 2 sec, duration rectangular surge passes through a line having surge impedance of 350 and approaches a station at which the concentrated earth capacitance is 3 103 pF. Calculate the maximum value of surge transmitted to the second line. [8+8] 1 of 2

Code No: R05310203

Set No. 4

5. (a) What is corona loss? Why is it dierent in dierent weather conditions? How can it be estimated? (b) A 132kV overhead line conductor of radius 1cm is built so that corona takes place if the line voltage is 210 kV (r.m.s). If the value of voltage gradient at which ionization occurs can be taken as 21.21 kV (r.m.s) per cm, determine the spacing between the conductors. [8+8] 6. (a) What do you mean by string eciency? How can it be improved? (b) A 3-phase overhead transmission line is being supported by three discs suspension insulators. The potential across the rst and second insulators are 11 kV and 13.2kV respectively. Calculate i. the line voltage and ii. string eciency. [8+8]

7. (a) Prove transmission line conductor between two supports at equal heights takes the form of a catenary. (b) A transmission line conductor at a river crossing is supported by two towers at heights of 50 and 80 meters above water level. The horizontal distance between the towers is 300 meters. If the tension in the conductor is 2000 kg, determine the clearance between the conductors and water at a point midway between the towers. [8+8] 8. (a) What are the causes of cable breakdown? What are voids? How are they formed? Why do voids lead to cable failure? (b) A single core lead sheathed cable is graded by using two dielectrics of relative permittivity 3.8 (inner) and 2.8 (outer), the thickness of each being 0.75cm. The core diameter is 1 cm; system voltage is 66 kV, 3-phase. Determine the maximum stress in two dielectrics. [8+8]

2 of 2

You might also like