OPERATORS MANUAL

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

PD30R-X-X-C
PE30R-X-X-C
RELEASED: REVISED: (REV. 04) 2-4-05 3-2-07

3 DIAPHRAGM PUMP
1:1 RATIO (METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS
Refer to Model Description Chart to match the pump material options. 637303-XX for fluid section repair (see page 4). Note: This kit also contains several air motor seals which will need to be replaced. 637369 for air section repair (see page 6). 637374-X major air valve assembly (see page 7).

3" DIAPHRAGM PUMP PD30R-XXX-XXX-C

PUMP DATA
Models . . . . . . . . . . . . . see Model Description Chart for -XXX". Pump Type . . . . . . . . . . Metallic Air Operated Double Diaphragm Material . . . . . . . . . . . . . see Model Description Chart. Weight . . . . PX30R-XCX-XXX-C . . . . . 242.3 lbs (109.9 kgs) PX30R-XSX-XXX-C . . . . . 253.3 lbs (114.9 kgs) Maximum Air Inlet Pressure . . . . . . . . . 120 p.s.i.g. (8.3 bar) Maximum Material Inlet Pressure . . . . . 10 p.s.i.g. (0.69 bar) Maximum Outlet Pressure . . . . . . . . . . 120 p.s.i.g. (8.3 bar) Maximum Flow Rate . . . . . . . . . . . . . . 237 g.p.m. (897 l.p.m.) flooded inlet . . . . . . . . . . . . . 275 g.p.m. (1041 l.p.m.) Displacement / Cycle @ 100 p.s.i.g. . . . 2.8 gal. (10.6 lit.) Maximum Particle Size . . . . . . . . . . . . 3/8" dia. (9.5 mm) Maximum Temperature Limits (diaphragm / ball / seat material) E.P.R. / EPDM . . . . . . . . . . . -60_ to 280_ F (-51_ to 138_ C) HytrelR . . . . . . . . . . . . . . . . -20_ to 150_ F (-29_ to 66_ C) KynarR PVDF . . . . . . . . . . . 10_ to 200_ F (-12_ to 93_ C) Nitrile . . . . . . . . . . . . . . . . . 10_ to 180_ F (-12_ to 82_ C) Polypropylene . . . . . . . . . . . 35_ to 150_ F (2_ to 66_ C) SantopreneR . . . . . . . . . . . . -40_ to 225_ F (-40_ to 107_ C) TeflonR P.T.F.E. . . . . . . . . . . 40_ to 225_ F (4_ to 107_ C) VitonR . . . . . . . . . . . . . . . . -40_ to 350_ F (-40_ to 177_ C) Dimensional Data . . . . . . . . . . . . . . . . see page 8 Mounting Dimensions . . . 10-5/32" x 12-1/16" (258 mm x 306 mm) Noise Level @ 70 p.s.i., 50 c.p.m. . . . . 83.0 db(A)
Tested with 67263 muffler assembly installed. The pump sound pressure levels published here have been updated to an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.

Figure 1

MODEL DESCRIPTION CHART

P X 30 R - X X X - X X X - C
Electronic Interface D - None. E - Available Air Motor / Air Cap Material R - Polypropylene / Stainless Steel Fluid Connection A - 3 - 8 N.P.T.F. - 1 B - Rp 3 (3 - 11 BSP, parallel) Fluid Caps & Manifold Material C - Cast Iron S - Stainless Steel Hardware Material P - Plated Steel S - Stainless Steel Seat Material A - Santoprene C - Hytrel E - Carbon Steel F - Aluminum G - Nitrile Ball Material A - Santoprene C - Hytrel G - Nitrile Diaphragm Material A - Santoprene B - Santoprene C - Hytrel H K L S - Hard 440 Stainless Steel - Kynar PVDF - HastelloyR - C - 316 Stainless Steel

NOTICE: All possible options are shown in the chart however certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

T - Teflon V - Viton

G - Nitrile T - Teflon / Santoprene V - Viton

FLUID SECTION SERVICE KIT SELECTION

EXAMPLE: Model # PD30R-ASS-SAA-C Fluid Section Service Kit # 637303-AA

PX30R - XXX - X X X - C 637303 - X X

Ball Diaphragm

INGERSOLL RAND COMPANY LTD

P.O. BOX 151 D ONE ARO CENTER D BRYAN, OHIO 43506-0151

& (800) 276-4658 D FAX (800) 266-7016

E2007

CCN 15227655

OPERATING AND SAFETY PRECAUTIONS

READ, UNDERSTAND, AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE. S Obtain Material Safety Data Sheets on all materials from the HAZARDOUS MATERIALS EXCESSIVE AIR PRESSURE supplier for proper handling instructions. HAZARDOUS PRESSURE STATIC SPARK WARNING EXPLOSION HAZARD. Models containing aluminum wetted parts cannot be used with 1,1,1-trichloroethane, methylene chloride or other halogenated hydrocarbon solWARNING EXCESSIVE AIR PRESSURE. Can cause personvents which may react and explode. al injury, pump damage or property damage. S Check pump motor section, fluid caps, manifolds and all Do not exceed the maximum inlet air pressure as stated on the wetted parts to assure compatibility before using with solvents pump model plate. of this type. Be sure material hoses and other components are able to withWARNING MISAPPLICATION HAZARD. Do not use models stand fluid pressures developed by this pump. Check all hoses for damage or wear. Be certain dispensing device is clean and containing aluminum wetted parts with food products for huin proper working condition. man consumption. Plated parts can contain trace amounts of lead. WARNING STATIC SPARK. Can cause explosion resulting in CAUTION Verify the chemical compatibility of the pump severe injury or death. Ground pump and pumping system. Use the pump grounding screw terminal provided. Use AROR wetted parts and the substance being pumped, flushed or repart no. 66885-1 ground kit or connect a suitable ground wire circulated. Chemical compatibility may change with tempera(12 ga. min.) to a good earth ground source. ture and concentration of the chemical(s) within the Secure pump, connections and all contact points to avoid substances being pumped, flushed or circulated. For specific vibration and generation of contact or static spark. fluid compatibility, consult the chemical manufacturer. Consult local building codes and electrical codes for specific CAUTION Maximum temperatures are based on mechanigrounding requirements. cal stress only. Certain chemicals will significantly reduce After grounding, periodically verify continuity of electrical path maximum safe operating temperature. Consult the chemical to ground. Test with an ohmmeter from each component (e.g., manufacturer for chemical compatibility and temperature limhoses, pump, clamps, container, spray gun, etc.) to ground to its. Refer to PUMP DATA on page 1 of this manual. insure continuity. Ohmmeter should show 0.1 ohms or less. CAUTION Be certain all operators of this equipment have Submerse the outlet hose end, dispensing valve or device in been trained for safe working practices, understand its limitathe material being dispensed if possible. (Avoid free streaming tions, and wear safety goggles / equipment when required. of material being dispensed.) CAUTION Do not use the pump for the structural support of Use hoses incorporating a static wire. the piping system. Be certain the system components are Use proper ventilation. properly supported to prevent stress on the pump parts. Keep inflammables away from heat, open flames and sparks. S Suction and discharge connections should be flexible connecKeep containers closed when not in use. tions (such as hose), not rigid piped, and should be compatible WARNING Pump exhaust may contain contaminants. Can with the substance being pumped. cause severe injury. Pipe exhaust away from work area and perCAUTION Prevent unnecessary damage to the pump. Do sonnel. not allow pump to operate when out of material for long periods In the event of a diaphragm rupture material can be forced out of time. of the air exhaust muffler. S Disconnect air line from pump when system sits idle for long Pipe the exhaust to a safe remote location when pumping hazperiods of time. ardous or inflammable materials. CAUTION Use only genuine ARO replacement parts to asUse a grounded 1" minimum i.d. hose between the pump and the muffler. sure compatible pressure rating and longest service life. WARNING HAZARDOUS PRESSURE. Can result in serious injury or property damage. Do not service or clean pump, WARNING = Hazards or unsafe practices which could hoses or dispensing valve while the system is pressurized. result in severe personal injury, death or Disconnect air supply line and relieve pressure from the syssubstantial property damage. tem by opening dispensing valve or device and / or carefully and slowly loosening and removing outlet hose or piping from CAUTION = Hazards or unsafe practices which could result in minor personal injury, product or pump. property damage. WARNING HAZARDOUS MATERIALS. Can cause serious = Important installation, operation or injury or property damage. Do not attempt to return a pump to NOTICE maintenance information. the factory or service center that contains hazardous material. Safe handling practices must comply with local and national laws and safety code requirements.

S S

S S S S S S S S S

S S S

Page 2 of 8

PD30R-X-X-C (en)

GENERAL DESCRIPTION
The ARO diaphragm pump offers high volume delivery even at low air pressure and a broad range of material compatibility options available. Refer to the model and option chart. ARO pumps feature stall resistant design, modular air motor / fluid sections. Air operated double diaphragm pumps utilize a pressure differential in the air chambers to alternately create suction and positive fluid pressure in the fluid chambers, valve checks insure a positive flow of fluid. Pump cycling will begin as air pressure is applied and it will continue to pump and keep up with the demand. It will build and maintain line pressure and will stop cycling once maximum line pressure is reached (dispensing device closed) and will resume pumping as needed.

MAINTENANCE
Refer to the part views and descriptions as provided on page 4 through 7 for parts identification and Service Kit information. S Certain ARO Smart Parts" are indicated which should be available for fast repair and reduction of down time. S Service kits are divided to service two separate diaphragm pump functions: 1. AIR SECTION, 2. FLUID SECTION. The FLUID SECTION is divided further to match typical part MATERIAL OPTIONS. S Provide a clean work surface to protect sensitive internal moving parts from contamination from dirt and foreign matter during service disassembly and reassembly. S Keep good records of service activity and include pump in preventive maintenance program. S Before disassembling empty captured material in the outlet manifold by turning the pump upside down to drain material from the pump.

AIR AND LUBE REQUIREMENTS

WARNING EXCESSIVE AIR PRESSURE. Can cause pump damage, personal injury or property damage. A filter capable of filtering out particles larger than 50 microns should be used on the air supply. There is no lubrication required other than the O" ring lubricant which is applied during assembly or repair. If lubricated air is present, make sure that it is compatible with the O" rings and seals in the air motor section of the pump.

S S

FLUID SECTION DISASSEMBLY

1. Remove top manifold(s). 2. Remove (22) balls, (19) O" rings (if applicable) and (21) seats. 3. Remove (15) fluid caps. NOTE: Only Teflon diaphragm models use a primary (7) diaphragm and a backup (8) diaphragm. Refer to the auxiliary view in figure 2. 4. Remove the (14) screw, (6) diaphragm washer, (7) or (7 / 8) diaphragms, (5) backup washer and (196) cushion. NOTE: Do not scratch or mar the surface of (1) diaphragm rod.

OPERATING INSTRUCTIONS S Always flush the pump with a solvent compatible with the material S S S S
being pumped if the material being pumped is subject to setting up" when not in use for a period of time. Disconnect the air supply from the pump if it is to be inactive for a few hours. The outlet material volume is governed not only by the air supply but also by the material supply available at the inlet. The material supply tubing should not be too small or restrictive. Be sure not to use hose which might collapse. When the diaphragm pump is used in a forced-feed (flooded inlet) situation it is recommended that a Check Valve" be installed at the air inlet. Secure the diaphragm pump legs to a suitable surface to insure against damage by vibration.

FLUID SECTION REASSEMBLY

SERVICE NOTE: ARO pn 204214-T diaphragm assembly tool is recommended for use when reassembling the pump. S Reassemble in reverse order. S Clean and inspect all parts. Replace worn or damaged parts with new parts as required. S Lubricate (1) diaphragm rod and (144) U" cup with LubriplateR FML-2 grease. (94276 grease packet is included in service kit.) S Be certain the diaphragm assembly bottoms out on the (1) rod, back off Teflon diaphragm assembly far enough to align holes. S For models with Teflon diaphragms: Item (8) Santoprene diaphragm is installed with the side marked AIR SIDE" towards the pump center body. Install the (7) Teflon diaphragm with the side marked FLUID SIDE" towards the fluid cap. S Re-check torque settings after pump has been re-started and run a while.

S HytrelR, VitonR and TeflonR are trademarks of the DuPont Company S KynarR is a registered trademark of Arkema Inc. S HastelloyR is a registered trademark of Haynes International Inc. S S SantopreneR is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. S LubriplateR is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) S S AROR is a registered trademark of Ingersoll-Rand Company S LoctiteR is a registered trademark of Henkel Loctite Corporation S

PD30R-X-X-C (en)

Page 3 of 8

PARTS LIST / PX30R-X-X-C FLUID SECTION

L 637303-XX FLUID SECTION SERVICE KITS INCLUDE: BALLS (see Ball Option, refer to -XX in chart below), DIAPHRAGMS (see Diaphragm Option, refer to -XX in chart below), and items; 3, 19, 70, 144, 175, 196, (listed below) plus (174) and 94276 Lubriplate FML-2 grease (page 6).

SEAT OPTIONS PX30R-XXX-XXX-C

21" -XXX -AXX -CXX -EXX -FXX Seat 94104-A 94104-C 95678 95674 Qty (4) (4) (4) (4) (4) [Mtl] [Sp] [H] [C] [A] [B] -XXX -HXX -KXX -LXX -SXX Seat 94114 94621-K 94939 94113 Qty (4) (4) (4) (4) [Mtl] [SH] [K] [Ha] [SS] -XXX -XAX -XCX -XTX -XVX

BALL OPTIONS PX30R-XXX-XXX-C

L 22" (3-1/4" dia.) Ball 94103-A 94103-C 94103-T 94103-V Qty (4) (4) (4) (4) (4) [Mtl] [Sp] [H] [B] [T] [V] L 19" (3/16" x 5" o.d.) Gasket 94115 Y327-350 Y325-350 Y328-350 Y327-350 Qty (4) (4) (4) (4) (4) [Mtl] [E] [V] [B] [T] [V]

-XGX 94103-G

-GXX 94104-G

NOTE: Seat options -AXX-C, -CXX-C and -GXX-C do not require item 19 O" ring.

DIAPHRAGM OPTIONS PX30R-XXX-XXX-C

L SERVICE KIT -XXX -XXA -XXB -XXC -XXT -XXV -XX = (Ball) -XX = (Diaphragm) 637303-XA 637303-XB 637303-XC 637303-XT 637303-XV L 7" Diaphragm 94091-A 94110-A 94091-C 94091-G 94090-T 95345 Qty (2) (2) (2) (2) (2) (2) [Mtl] [Sp] [Sp] [H] [B] [T] [V] L 8" Diaphragm 94110-A Qty (2) [Mtl] [Sp] L 3" (1/8" x 1" o.d.) O" Ring Y328-210 Y328-210 Y327-210 Y328-210 Y328-210 Y327-210 Qty (2) (2) (2) (2) (2) (2) [Mtl] [T] [T] [V] [T] [T] [V]

MATERIAL CODE
[A] = Aluminum [B] = Nitrile [C] = Carbon Steel [Co] = Copper [CI] = Cast Iron [E] = E.P.R. [H] = Hytrel [Ha] = Hastelloy - C [K] = Kynar PVDF [SH] = Hard Stainless Steel [Sp] = Santoprene [SS] = Stainless Steel [T] = Teflon P.T.F.E. [V] = Viton

-XXG 637303-XG

MANIFOLD THREAD / FLUID CAP MATERIAL OPTIONS PX30R-XXX-XXX-C

Cast Iron PX30R-ACX-XXX-C N.P.T.F. Item Description (size) Qty (2) (2) (1) (1) Part No. 94106 94701-2 94305-1 94702-1 [Mtl] [CI] [SS] [CI] [CI] 15 Fluid Cap 32 Leg 60 Inlet Manifold 61 Outlet Manifold 94106 94701-2 94305-2 94702-2 PX30R-BCX-XXX-C BSP Part No. [Mtl] [CI] [SS] [CI] [CI] 94107 94703-2 94216-1 94704-1 Stainless Steel PX30R-ASX-XXX-C N.P.T.F. Part No. [Mtl] [SS] [SS] [SS] [SS] 94107 94703-2 94216-2 94704-2 PX30R-BSX-XXX-C BSP Part No. [Mtl] [SS] [SS] [SS] [SS]

EXTERNAL HARDWARE OPTIONS PX30R-XXX-XXX-C

PX30R-XXP-XXX-C Item Description (size) Qty Part No. [Mtl] [C] [C] [C] 26 Screw (M12 x 1.75 - 6g x 45 mm) 27 Screw (M12 x 1.75 - 6g x 60 mm) 29 Nut (M12 x 1.75 - 6g) (12) 94412-1 (16) 94991-1 (16) 95053-1 PX30R-XXS-XXX-C Part No. 94412-2 94991 95053 [Mtl] [SS] [SS] [SS]

COMMON PARTS
Item Description (size) 1 Rod 5 Backup Washer 6 Fluid Side Washer 9 Washer (3/16" i.d. x 2" o.d. x 5/32") 14 Cap Screw (3/4" - 16 x 3-1/4") 68 Air Cap 69 Air Cap
L n 70

Qty (1) (2) (2) (2) (2) (1) (1) (2)

Part No. 94984 94831-2 94803 Y13-12-T Y5-134-T 94031-1 94031-2 94100

[Mtl] [C] [SS] [SS] [SS] [SS] [SS] [SS] [B]

Item

Description (size)

Qty (1) (2) (4) (2) (2) (4) (4) (2)

Part No. Y17-50-S Y17-51-S 96656 Y186-51 Y325-117 94098 Y178-56-S 94631

[Mtl] [SS] [SS] [SS] [B] [B] [Co] [SS] [Sp]

V 76 Pipe Plug (1/8 - 27 N.P.T. x 0.27")

126 Pipe Plug (1/4 - 18 N.P.T. x 7/16") 131 Screw (M10 x 1.5 - 6g x 120 mm)
Ln144 Ln175 n 180 L 196

U" Cup (3/16" x 1-3/8" o.d.) O" Ring (3/32" x 1" o.d.) Gasket (0.406" i.d. x 0.031" thick) Cushion

181 Roll Pin (5/32" o.d. x 3/4" long)

Gasket

V Used with models PE30R-XXX-XXX-C only. n Air motor kit parts, see page 6.

Page 4 of 8

PD30R-X-X-C (en)

PARTS LIST / PX30R-X-X-C FLUID SECTION

COLOR CODE
DIAPHRAGM MATERIAL COLOR BALL COLOR Cream Red (S) Tan N/A White Yellow (S)
(S) Dot

3 5

1 8

61 26 , G

Hytrel Cream Nitrile Black Santoprene Tan Santoprene Green (Backup) Teflon P.T.F.E. White Viton Yellow (-)

7 2 4

181

68 144 k 144 k 70 k

FOR THE AIR MOTOR SECTION SEE PAGES 6 & 7 76 u 1 5

Torque Sequence

196

22 21 19 = k

126 u

175 k 70 k

175 k 27 , G 69 60 26 , G 32 22 19 = k 21 Figure 2 180 131 , x 3k 14 , g 15

29

. TORQUE REQUIREMENTS ,
NOTE: DO NOT OVERTIGHTEN FASTENERS. ALL FASTENERS ARE METRIC.
(14) Cap screw 65 - 70 ft lbs (88.1 - 94.9 Nm). (26 and 27) Fluid cap / manifold screw 60 - 70 ft lbs (81.4 - 94.9 Nm). (131) Screw, 35 - 40 ft lbs (47.5 - 54.2 Nm).

VIEW OF TWO PIECE TEFLON DIAPHRAGM

7
TEFLON

LUBRICATION / SEALANTS
Apply Lubriplate FML-2 grease to all O" rings, U" Cups & mating parts. Apply LoctiteR 242 to threads at assembly. Apply Teflon tape to threads at assembly. Apply Loctite 271 to threads. Apply anti-seize compound to threads and bolt and nut flange heads which contact pump case when using stainless steel fasteners.

x u

g G

= NOT USED WITH PX30R-XXX-AXX-C, -CXX-C & -GXX-C.

Z Lubriplate FML-2 is a white food grade petroleum grease. MSDS available upon request.

8
SANTOPRENE

PD30R-X-X-C (en)

Page 5 of 8

PARTS LIST / PX30R-X-X-C AIR SECTION

n Indicates parts included in 637369 Air Section Service Kit shown below and items (70), (144), (175) and (180) shown on page 4.

AIR MOTOR PARTS

Item Description (size) Qty Part No. (1) (1) (4) (2) (1) (2) (2) (1) (1) (8) (8) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (2) (1)
(PD30R-X-X-C) (PE30R-X-X-C)

[Mtl] [P] [D] [SS] [SS] [D] [SS] [D] [C / I] [B] [SS] [SS] [P] [P] [P] [B] [B] [B] [Ck] [Ck] [B] [D] [U] [B]

Item n 171 n 172 n 173

Kn 174

Description (size) O" Ring (3/32" x 1-1/8" o.d.) O" Ring (1/16" x 1-1/8" o.d.) O" Ring (1/16" x 1-3/8" o.d.) O" Ring (1/8" x 1/2" o.d.)

Qty Part No. (1) (1) (1) (2) (2) (2) (1) (1) (1) (2) (1) (4) (1) (1) (1) 94081 Y325-119 Y325-22 Y325-26 Y325-202 94102 95666 95665 94810 Y325-202 95761 95924 Y325-204 Y325-208 94276 637308

[Mtl] [Br] [B] [B] [B] [B] [Sp] [B] [B] [B] [P] [SS] [B] [B]

101 Center Body 103 Bushing 105 Screw (M6 x 1 - 6g x 180 mm) 107 End Plate 111 Spool 118 Actuator Pin (0.250" x 2.276" long) 121 Sleeve
~

95667 94092 95921 95846 95651 94083 94084 94860 94099 95931 95923 95789 95789-1 95790 Y325-32 95966 Y186-50 95650 95659 94026 67164 94433 Y240-9

170 Piston Sleeve

n 176 Diaphragm (check valve) n 199 Track Gasket n 200 Gasket

~

127 90 St. Elbow (1-1/2 - 11-1/2 N.P.T.) 133 Washer (M6) 134 Screw (M6 x 1 - 6g x 35 mm) 135 Valve Block 136 End Cap

n 132 Gasket

201 Muffler O" Ring (1/8" x 1/2" o.d.) 233 Adapter Plate 236 Nut (M6 x 1 - 6g)

n 232

n 243 n 244

O" Ring (1/8" x 5/8" o.d.) O" Ring (1/8" x 7/8" o.d.) Lubriplate Grease Packets (10)

n 137 n 138 n 139

O" Ring (1/16" x 2" o.d.) U" Cup (3/16" x 1.792" o.d.) U" Cup (3/16" x 1-1/4" o.d.)

L n Lubriplate FML-2 Grease

~

Items not shown

140 Valve Insert 141 Valve Plate n 166 Track Gasket n 167 Pilot Piston (includes 168 and 169) 168 169 O" Ring (3/32" x 5/8" o.d.) U" Cup (1/8" x 7/8" o.d.)

MATERIAL CODE
[B] = [Br] = [C] = [Ck] = Nitrile Brass Carbon Steel Ceramic [D] = Acetal [I] = Iron [P] = Polypropylene [Sp] = Santoprene [SS] = Stainless Steel [U] = Polyurethane

K Fluid Section Service Kit parts, see page 4.

AIR MOTOR SECTION SERVICE

Service is divided into two parts 1. Pilot Valve, 2. Major Valve. GENERAL REASSEMBLY NOTES: S Air Motor Section service is continued from Fluid Section repair. S Inspect and replace old parts with new parts as necessary. Look for deep scratches on surfaces, and nicks or cuts in O" rings. S Take precautions to prevent cutting O" rings upon installation. S Lubricate O" rings with Lubriplate FML-2 grease. S Do not over-tighten fasteners, refer to torque specification block on view. S Re-torque fasteners following restart. S SERVICE TOOLS To aid in the installation of (168) O" rings onto the (167) pilot piston, use tool # 204130-T, available from ARO.

MAJOR VALVE DISASSEMBLY

1. Remove (135) valve block and (233) adapter plate, exposing (132 and 166) gaskets, (232) O" ring and (176) checks. 2. Remove (233) adapter plate, releasing (140) valve insert, (141) valve plate, (199 and 200) gaskets and (244, 243 and 232) O" rings. 3. Remove (136) end cap and (137) O" ring, releasing (111) spool.

MAJOR VALVE REASSEMBLY

1. Install new (138 and 139) U" cups on (111) spool LIPS MUST FACE EACH OTHER. 2. Insert (111) spool into (135) valve block. 3. Install (137) O" ring on (136) end cap and assemble end cap to (135) valve block, securing with (107) end plates and (105) screws. 4. Install (140) valve insert and (141) valve plate into (135) valve block. NOTE: Assemble (140) valve insert with dished" side toward (141) valve plate. Assemble (141) valve plate with 2 identification dots toward (199 and 200) gaskets. 5. Assemble (244, 243 and 232) O" rings, (199 and 200) gaskets and (233) adapter plate to (135) valve block. 6. Assemble (132 and 166) gaskets, (176) checks and (232) O" ring to (101) body. 7. Assemble (135) valve block and components to (101) body, securing with (134) screws.

PILOT VALVE DISASSEMBLY

1. A light tap on (118) should expose the opposite (121) sleeve, (167) pilot piston and other parts. 2. Remove (170) sleeve, inspect inner bore of sleeve for damage.

PILOT VALVE REASSEMBLY

1. Clean and lubricate parts not being replaced from service kit. 2. Install new (171 and 172) O" rings, replace (170) sleeve. 3. Install new (168) O" rings and (169) seal - Note the lip direction. Lubricate and replace (167). 4. Reassemble remaining parts, replace (173 and 174) O" rings.
Page 6 of 8

PD30R-X-X-C (en)

PARTS LIST / PX30R-X-X-C AIR SECTION

118 121 k 174 k 173 167

169 k 168 k

172 k 171 k 170

PILOT VALVE PART GROUP

140 107 . 105 133 135

141 k

244 k 243 k 132 k 166 k

173 k 121 118 174 k 103 101

. 134

199 k 232 k 200 k 138 k 111

233

232 k

176 k

Optional 94117 Muffler

MAJOR VALVE

139 k 137 k 136 107 236 . TORQUE REQUIREMENTS ,

NOTE: DO NOT OVERTIGHTEN FASTENERS. ALL FASTENERS ARE METRIC.
Torque (105) screw to 35 - 40 in. lbs (4.0 - 4.5 Nm). Torque (134) screw to 35 - 40 in. lbs (4.0 - 4.5 Nm). k Apply Lubriplate FML-2 grease to O" rings, U" Cups & mating parts.

LUBRICATION / SEALANTS

A replacement Major Valve Service Assembly is available separately, which includes the following: Models PD30R-X-X-C: 637374: 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140, 141, 166, 176 (2), 199, 200, 232 (2), 233, 236 (4), 243 and 244. Models PE30R-X-X-C: 637374-1: 76, 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140, 141, 166, 176 (2), 199, 200, 232 (2), 233, 236 (4), 243 and 244. PD30R-X-X-C (en)

Figure 3
Page 7 of 8

TROUBLE SHOOTING
Product discharged from exhaust outlet. S Check for diaphragm rupture. S Check tightness of (14) cap screw. Air bubbles in product discharge. S Check connections of suction plumbing. S Check O" rings between intake manifold and fluid caps. S Check tightness of (14) cap screw. Motor blows air or stalls. S Check (176) check valve for damage or wear. S Check for restrictions in valve / exhaust. Low output volume, erratic flow, or no flow. S Check air supply. S Check for plugged outlet hose. S Check for kinked (restrictive) outlet material hose. S Check for kinked (restrictive) or collapsed inlet material hose. S Check for pump cavitation - suction pipe should be sized at least as large as the inlet thread diameter of the pump for proper flow if high viscosity fluids are being pumped. Suction hose must be a non-collapsing type, capable of pulling a high vacuum. S Check all joints on the inlet manifolds and suction connections. These must be air tight. S Inspect the pump for solid objects lodged in the diaphragm chamber or the seat area.

DIMENSIONAL DATA
(Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).

Air Inlet 3/4 - 14 N.P.T.

3 - 8 N.P.T.F. - 1 (PX30R-AXX-XXX-C) Rp 3 (3 - 11 BSP parallel) (PX30R-BXX-XXX-C) A"

17-11/16" (449.2 mm) 15" (381 mm) 2-3/4"

(69.9 mm)

Outlet

30"
(761.7 mm)

32"
(812.5 mm)

C"

Dotted lines show optional 67263 Muffler Assembly.

B"
Inlet

9/16" Slot (14.3 mm) 12-3/16" (309.6 mm)

OPTIONAL ACCESSORY: 66109 Air Line Connection Kit

Exhaust Port 1-1/2 - 11-1/2 N.P.S.M.

10-5/32" (258 mm) 11-11/16" (296.1 mm) 23-3/32" (586.3 mm)

PX30R-XCX-XXX-C PX30R-XSX-XXX-C

A" 23-5/8" (598.7 mm) 23-1/8" (587.3 mm)

B" 2-7/16" (61.1 mm) 2-3/4" (69.9 mm)

C" 15-9/16" (394.8 mm) 16" (406.4 mm)

Figure 4

PN 97999-1111 Page 8 of 8 PD30R-X-X-C (en)