Scribd Logo
Upload

Welcome to Scribd!

  • 132 views

    Spin Flash Dryer General Description: The Wet Product Is Introduced in The Form at Which It Leaves The Preceding

    Uploaded by

    Deepak
    The wet product enters the dryer through a screw feeder and is partially grated and homogenized before entering the drying chamber. In the drying chamber, an agitator breaks up lumps and disintegrates the product while hot air dries the particles. Lighter, drier particles move to the center and exit through the top while heavier, wetter particles continue drying. An equilibrium is reached where the feed and discharge rates balance to produce dried product at the desired specification. The self-adjusting residence time dries each particle only as long as needed, avoiding over-drying sensitive products even at high temperatures.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd

    Spin Flash Dryer General Description: The Wet Product Is Introduced in The Form at Which It Leaves The Preceding

    Uploaded by

    Deepak
    132 views1 page
    The wet product enters the dryer through a screw feeder and is partially grated and homogenized before entering the drying chamber. In the drying chamber, an agitator breaks up lumps and disintegrates the product while hot air dries the particles. Lighter, drier particles move to the center and exit through the top while heavier, wetter particles continue drying. An equilibrium is reached where the feed and discharge rates balance to produce dried product at the desired specification. The self-adjusting residence time dries each particle only as long as needed, avoiding over-drying sensitive products even at high temperatures.

    Original Title

    Flash Dryer

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The wet product enters the dryer through a screw feeder and is partially grated and homogenized before entering the drying chamber. In the drying chamber, an agitator breaks up lumps and disintegrates the product while hot air dries the particles. Lighter, drier particles move to the center and exit through the top while heavier, wetter particles continue drying. An equilibrium is reached where the feed and discharge rates balance to produce dried product at the desired specification. The self-adjusting residence time dries each particle only as long as needed, avoiding over-drying sensitive products even at high temperatures.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    132 views1 page

    Spin Flash Dryer General Description: The Wet Product Is Introduced in The Form at Which It Leaves The Preceding

    Uploaded by

    Deepak
    The wet product enters the dryer through a screw feeder and is partially grated and homogenized before entering the drying chamber. In the drying chamber, an agitator breaks up lumps and disintegrates the product while hot air dries the particles. Lighter, drier particles move to the center and exit through the top while heavier, wetter particles continue drying. An equilibrium is reached where the feed and discharge rates balance to produce dried product at the desired specification. The self-adjusting residence time dries each particle only as long as needed, avoiding over-drying sensitive products even at high temperatures.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 1

    SPIN FLASH DRYER General Description: The wet product is introduced in the form at which it leaves the preceding

    process, as for example in the cake form. The incoming feed is partially grated, homogenized and forced down into the screw feeder. The screw has a variable drive enabling it to convey the product into the drying chamber, which allows the required drying of the product. The agitator / disintegrator / lump-breaker in the drying chamber bottom rotates at suitable RPM, assisting the lump breaking/disintegration. The hot drying air from the air distributor carries away the dried particles. The powder loaded air is taken out at the chamber top, led to the bag filter and separated through the rotary valve. The described process flow is of course basic and there are numerous combinations of process flows depending on the actual requirement. The drying mechanism The wet product drops down in the chamber bottom from the screw conveyor. The rotating agitator breaks the lumps in the chamber bottom and mechanical disintegration starts. The drying air is led tangentially into the air distributor and consequently a high velocity whirling gas flow moves up through the chamber walls. When the particle through attrition and disintegration looses settling velocity they get transported to the chamber top and leave. As the smallest and most dry particles move towards the axis of the eddy in the chamber. With a correct selection of operating conditions a state of equilibrium is obtained, in which the supply rate of moist material is in balance with the corresponding discharge rate of dried product of a desired specification. It is an important feature that the particles remain in the drying zone, just as long as it takes to dry them out and no longer. This self-adjusting residence time is rather unique and is generally not found in other drying processes. Due to effective and self controlling drying process, the influence from heat on heat sensitive products is remarkable low even at high drying temperature.

    You might also like