Cookbook

for
EMC
Precompliance
Measurements

A Guide to Making
Precompliance Conducted and
Radiated Emissions Measurements
with Spectrum Analyzers
and EMC Analyzers
Table of Contents 1. 0 Introduction to Precompliance Measurements 3
1.1 Precompliance Measurements versus Full Compliance
Measurements 5
2.0 EMI Precompliance Systems 5
3.0 Precompliance Measurements Process 6
4.0 Emissions Testing 9
4.1 Introduction 9
4.2 Conducted Emissions Measurements Preparation 9
4.3 Performing Conducted Emissions Measurements 13
4.4 Starting the Conducted Measurements Process 13
4.4.1 Overload Test 14
4.4.2 Signal Measurements 14
4.5 Radiated Emissions Measurements Preparation 15
4.6 Measuring Radiated Emissions 17
4.7 Ambient Signal Measurements 17
4.8 Placement of EUT for Maximum Signals 18
4.9 Ambient Plus EUT Measurements 19
4.10 Evaluating Measurement Results 21
4.11 Report Development 22
5.0 Problem Solving and Trouble Shooting 24
5.1 Diagnostics Testing Setup 25
5.2 Problem Isolation 25

Appendix A
Line Impedance Stabilization Networks (LISN) 28
A1.0 Purpose of a LISN 28
A1.1 LISN Operation 28
A1.2 Types of LISNs 29
A2.0 Transient Limiter Operation 29

Appendix B
Antenna Factors 30
B1.0 Field Strength Units 30
B1.1 Antenna Factors 30
B1.2 Types of Antennas Used for Commercial
Radiated Measurements 31

Appendix C
Basic Electrical Relationships 32

Appendix D
Detectors Used in EMI Measurements 33
D1.0 Peak Detector 33
D1.2 Peak Detector Operation 33
D2.0 Quasi-Peak Detector 34
D2.1 Quasi-Peak Detector Operation 34
D3.0 Average Detector 35

D3.1 Average Detector Operation 35

Appendix E
Regulatory Agency Addresses 36

Glossary 40
 3

1.0 Introduction to Note: precompliance measurements can be made with a variety of

Precompliance spectrum analyzers and EMC analyzers having the appropriate
Measurements detectors and bandwidth filters. In this application note, detailed
measurement procedures are provided for HP 8590EM series
EMC analyzers. However, these procedures can be adapted to other
instruments.

The concept of getting a product to market on time and within

budget is nothing new. However, companies have added some
new steps to the introduction process to achieve those goals.
One of those steps in the process is the addition of an EMC (elec-
tro-magnetic compatibility) strategy. Manufacturers have realized
that in order to sell their electronic products on the commercial
market, they must pass EMC requirements. Waiting until the end
of the development cycle to find out whether or not a product pass-
es regulatory agency requirements can be a costly gamble. Failing
to pass can result in costly redesign. Because of this, developers
are concerned about the EMC performance of a new product from
design investigation to preproduction units. Figure 1 below shows
a typical product development cycle.

Product Development Cycle

Initial Design Lab Production Production

Investigation Breadboard Prototype Prototype Unit
Yes Yes
viable pass pass pass pass

No No No No No

R E D E S I G N Production

Figure 1. A typical product development cycle.

Many manufacturers use EMI precompliance measurement sys-

tems to perform conducted and radiated EMI emissions tests prior
to having the product sent to a test facility for full compliance test-
ing. Conducted emissions testing focuses on signals, present on the
AC mains, that are generated by the EUT (equipment under test).
The test range for these measurements are from 9 kHz to
30 MHz depending on the regulation.
 4

Radiated emissions testing looks for signals broadcasted from the

EUT through space. The frequency range for these measurements
is between 30 MHz and 1 GHz depending on the regulation.
Testing to higher frequencies may be required depending on the
device and the internal clock frequency. This preliminary testing
is called precompliance testing. Figure 2 illustrates the relation-
ship between radiated emissions, radiated immunity, conducted
emissions and conducted immunity. Radiated immunity is the abil-
ity of a device or product to withstand radiated electromagnetic
fields. Conducted immunity is the ability of a device or product to
withstand electrical disturbances on power or data lines. In order
to experience an electromagnetic compatibility problem such as
when an electric drill interferes with TV reception, there must be
a generator or source, a coupling path, and a receptor. An EMC
problem can be eliminated by removing one of the components,
generator, coupling path, or receptor.

Until recently, most of the concentration has been to reduce the

generator emissions to remove an EMC problem. That is, reduce
the emissions from the source to an acceptable level.

With the advent of the new European requirements, there is

additional focus on product immunity. The level of electrical
field that a receptor can withstand before failure is known as
the product immunity. The term immunity and susceptibility
are used interchangeably. Immunity testing will not be covered
in this document.

Two Types of EMC Measurements

Emission Immunity = Susceptibility

Conducted
Radiated

Figure 2. Electromagnetic compatibility between products.

 5

1.1 Precompliance Measurements versus

Full Compliance Measurements

Full compliance measurements require the use of a receiver that

meets the requirements set forth in the CISPR1 part 16 document,
a qualified open area test site, and an antenna tower and turntable
to maximize the signals from the EUT. Great effort is taken to get
the best accuracy and repeatability. This can be very expensive.
The photograph below shows a full compliance test facility.

Precompliance measurements are intended to give an approxima-

tion of the EMI performance of the EUT. The cost of performing
precompliance tests is a fraction of full compliance measurements.
The more attention to detail, such as a good ground plane and min-
imize the number of reflective objects in the measurement area,
the better the accuracy of the measurements.

2.0 EMI
Precompliance Systems The contents of a precompliance test system (the HP 84110EM pre-
production evaluation system, for example) includes an EMC ana-
lyzer or spectrum analyzer, a line impedance stabilization network
(LISN), antennas, close field probes, and interconnection cables
(Figure 3). The test environment for precompliance testing
is usually less controlled than full compliance testing, which is per-
formed on an open area test site (OATS).

1. Comite International Special des Perturbations Radioelectriques

 6

The HP 84110EM
EMC Preproduction Evaluation System
HP 8591EM
EMC Analyzer
HP 8447F HP 11967D HP 11955A
Preamplifier LISN Biconical Antenna
INPUTS OUTPUTS MONITOR

LINE POWER OUTPUT

OFF ON CAUTION
HIGH VOLTAGE GND

HP 11947 HP 11940A/11941A HP 11956A HP 11968C

Transient Limiter Close-Field Probe Set Log Periodic Antenna Antenna Tripod

Figure 3. Components of a preproduction evaluation system.

3.0 Precompliance
Measurements Process
The precompliance measurement process is fairly straight forward.
However, before measurements can be performed on a product,
some preliminary questions must be answered.

1. Where is the product to be sold (i.e., United States, Europe,

Japan, etc.)?

2. What is the classification of the product (i.e., information

technology equipment [ITE] devices); industrial, scientific,
medical [ISM devices]; automotive or communications)?

3. Where is the product to be used (i.e., home, commercial,

light industry, or heavy industry)?

With the answers to the above questions, you can then determine
to which requirements your product must be tested. For example,
if you have determined that your product is an ITE device and you
are going to sell it in the United States then you need to test the product
to the FCC part 15 regulation. See Tables 1a, 1b, and 1c below to choose
the requirement for your product. When in doubt, call the appropriate
agency for final conformation of the applicable requirement. (A list of
phone numbers is included in the Appendix E.)
 7

International Regulations Summary

(Emissions)
CISPR FCC EN's Description
11 Part 18 EN 55011 Industrial, Scientific and Medical
12 (SAE) Automotives
13 Part 15 EN 55013 Broadcast Receivers
14 EN 55014 Household Appliances/tools
15 En 55015 Fluorescent lights/luminaries
16 Measurement apparatus/methods
22 Part 15 EN 55022 Information technology equipment
EN 50081-1, 2 Generic emissions standards

Table 1a. Comparison of regulatory agency requirements.

European Norms that Exist Now

Equipment Type Emissions

■ Generic Equipment EN 50081-1

■ Residential
■ Light Industrial

■ Industrial EN 50081-2
■ Information Technology Equipment (ITE) EN 55022
■ Industrial, Scientific, Medical Products (ISM) EN 55011

Table 1b. Major European requirements.

European Norms Detail Description

EN55011 (CISPR 11)

Industrial, Scientific, and Medical Products.

Class A: Used in establishments other than domestic areas.
Class B: Suitable for use in domestic establishments.
Group 1 Laboratory, medical, and scientific equipment.
(For example: signal generators, measuring receivers, frequency
counters, spectrum analyzers, switching mode power supplies,
weighing machines, and electronic microscopes.)

Group 2 Industrial induction heating equipment, dielectric heating

equipment, industrial microwave heating equipment, domestic
microwave ovens, medical apparatus, spark erosion equipment
and spot welders. (For example: metal melting, billet heating,
component heating, soldering and brazing, wood gluing, plastic
welding, food processing, food thawing, paper drying, microwave
therapy equipment.)

EN55014 (CISPR 14)

Electric motor-operated and thermal appliances for household and

similar purposes, electric tools, and electric apparatus. Depending
on the power rating of the item being tested, use one of the limits
shown in the table on the following page.
 8

(ROM card file names)

Household and similar appliances (conducted) EN014-HL
Household and similar appliances (radiated) EN014-HH
Motors < 700W (conducted) EN014-P1
Motors < 700W (radiated) EN014-P4
Motors <1000W (conducted) EN014-P2
Motors <1000W (radiated) EN014-P5
Motors >1000W (conducted) EN014-P3
Motors >1000W (radiated) EN014-P6

Note: The conducted range is 150 kHz to 30 MHz and the radiat-
ed range is 30 MHz to 300 MHz.

EN55022 (CISPR 22)

Information Technology Equipment

Equipment with the primary function of data entry, storage,
displaying, retrieval, transmission, processing, switching, or con-
trolling. (For example, data processing equipment, office machines,
electronic business equipment, telecommunications equipment.)
Class A ITE: Not intended for domestic use.
Class B ITE: Intended for domestic use.

FCC
(Federal Communications Commission)
Equipment FCC

■ Broadcast receivers Part 15

■ Household appliances/tools
■ Fluorescent lights/luminaries
■ Information Technology Equipment (ITE)
■ Industrial, Scientific, Medical Products (ISM) Part 18
■ Conducted measurements: 450 kHz - 30 MHz
■ Radiated measurements: 30 MHz - 1000 MHz, 40 GHz

Table 1c. FCC requirements summary.

Federal Communications Commission Equipment

Detailed Description

FCC Part 15
Radio frequency devices—unintentional radiators (For example,
TV broadcast receivers, FM broadcast receivers, CB receivers,
scanning receivers, TV interface device, cable system terminal
device, Class B personal computers and peripherals, Class B
digital devices, Class A digital devices and peripherals, external
switching power supplies.
Class A digital devices are marketed for use in a commercial,
industrial, or business environment.
Class B digital devices are marketed for use in a residential
environment.
 9

4.0 Emissions Testing 4.1 Introduction

After the appropriate regulations have been identified, the next

step is to setup the test equipment and perform radiated and
conducted emissions tests. The first group of tests to perform are
conducted emissions tests. The process we will follow will be to
interconnect the equipment, load in the appropriate limit line
from the ROM card, correct for the LISN and transient limiter
(see Appendix A), and perform the tests.

4.2 Conducted Emissions Measurements Preparation

Emissions testing is divided into conducted emissions and radiated

emissions testing. Conducted emissions testing is the easiest to
perform. Follow these steps to setup the equipment and the equip-
ment under test.
Conducted EMI: Measurement Setup
HP 8591EM
EMC Analyzer Printer

HP 11967D
LISN
MONITOR

POWER OUTPUT

CAUTION
HIGH VOLTAGE GND

HP 11947
Transient Limiter

EUT

Figure 4. Conducted measurements interconnection.

1. Interconnect the EMC analyzer, limiter, LISN, and EUT

as shown in Figure 4 (printer is optional).

(Operation of the LISN and the limiter is covered in Appendix A.)

2. Power up the EMC analyzer.

3. Setup the correct frequency range. Press [SETUP],

<150 kHz - 30 MHz>.
 10

4. Select and load the limit line from the ROM card supplied
based on the type of equipment and the regulatory agency
requirements. Selecting and loading limit lines is accomplished
by pressing the following buttons on the EMC analyzer:

[SETUP], <More>, <Limit Lines>, <RECALL LIMITS>,

scroll down and highlight the required limit line (i.e.,
lEN022_BC which is the conducted limits for Class B
products). Press <LOAD FILE>. (See Figures 5a and 5b)

Figure 5a. Partial list of regulatory limits.

Figure 5b. Regulatory limits displayed.

 11

5. Correct for the LISN. The ROM card contains typical correction
factors. To correct the display for the LISN press the following
buttons:

[SETUP], <More>, <Correctn factors>, <Antenna Factors>,

<RECALL ANTENNAS>. Scroll down to the LISN you are
using. Press <LOAD FILE>. Hewlett-Packard offers two
LISNs, HP 11967C (25 amps) and HP 11967D (10 amps).
(See Figures 6a and 6b)

Figure 6a. List of typical transducers.

Figure 6b. Display corrected for LISN factors.

 12

6. Correct the display for the HP 11947A transient limiter by

pressing the following buttons:

[SETUP], <More>, <Correctn Factors>, <Other Factors>,

<RECALL OTHER>, select HP 11947A and <LOAD FILE>.
( See Figures 7a and 7 b)

Figure 7a. List of amplifiers and limiter.

Figure 7b. Display corrected for limiter losses.

 13

4.3 Performing Conducted Emissions Measurements

At this point the EMC analyzer is setup with all the correct para-
meters including bandwidth, frequency range, LISN and limiter
compensation, and limit line. There is one more thing to consider
before starting conducted measurements — the effect of the ambi-
ent environment on the results. The power cable between the LISN
and the EUT can act as an antenna which can cause false EUT
responses on the display. To test that this phenomenon is not
occurring, switch the power of the EUT off and check the display
to ensure that the noise floor and ambient signals are at least 6 dB
below the limit line (see Figure 8).

Figure 8. Noise picked up by power cord with EUT off.

If signals appear above the limit line on the display, the inter-
connecting power cord may need to be shortened or a shield may
be needed around the cord. Do not use a ferrite core around the
power cord because the common mode signals coming from the
EUT can also be attenuated giving false indications.

4.4 Starting the Conducted Measurement Process

Turn on the EUT power and observe the display. If no signals

appear above the limit line, the product passes the conducted
emissions limit and your job is done. Most of the time, testers
are not so lucky. There are usually signals above the limit that
need closer analysis.

Conducted emissions usually occur in the lower end of the band.

One of the ways to take a closer look at the lower end of the band
is to switch to log frequency sweep. Log sweep expands the lower
decades.
Press [FREQUENCY], <SWEEP LOG>
The display is in a log frequency format. As you can see on the dis-
play, the signals at the lower frequencies are more defined in
log swept mode than in linear frequency mode.
 14

4.4.1 Overload Test

Before starting the measurements, you should test to ensure that

the EMC analyzer is not in overload. An overload condition occurs
when the energy level at the input mixer of the EMC analyzer very
high causing errors in amplitude measurements. To test for this
condition do the following: Press [AMPLITUDE], <ATTN MAN>,
up arrow which increases the attenuation before the input mixer
of the EMC analyzer. If the signal does not change position on the
display then the mixer is not over loaded. If the amplitude of the
signal does change then the input is overloaded and additional
attenuation must be added.

4.4.2 Signal Measurements

The next step is to perform a quasi-peak measurement on signals

above the limit line. One method is to use the “measure at mark”
function.

To measure the peak and quasi-peak level of a signal (see Appendix

D), perform the following:

Press [SETUP], <more>, <Detectors>, underline

<DETECTORS, PK, QP>. Press [WINDOWS ON], use <ZONE
CENTER> and <ZONE SPAN> to show the signals of interest
in the active trace. (See Figure 9)

Figure 9. Conducted emissions from EUT in log format.

To measure the peak and quasi-peak level of a signal of interest

press [TEST] then use the knob or the up/down keys to place the
marker on the signal.

Press <MEASURE AT MKR>. After the measurement is

completed, the signal frequency, peak, and quasi-peak
amplitudes will appear in the box above the display.
Press <ADD TO LIST>
 15

Repeat the measurement procedure until all the signals above the
limit line have been measured.

At this point, all the measured signal values are in the internal list
of the EMC analyzer. To view the list and determine which signal’s
quasi-peak levels are above the limit do the following.

Press <SIGNAL LIST ON>

Press <VIEW DELTA> until VIEW QP ∆ LIM 1 is shown.

(See Figure 10)

Figure 10. List of measured signals.

If there are no quasi-peak values above the limit line (positive

values) then your job is done and the product passes conducted
emissions tests.

If some of the quasi-peak values are above the limit line,

troubleshooting and redesign are required.

4.5 Radiated Emissions Measurements Preparation

Performing radiated emissions measurements is not as straight for-

ward as performing conducted EMI measurements. There is the
added complexity of the ambient environment which could interfere
with the emissions from the EUT. There are methods to differential
between ambient environment signals (TV, FM, and cellular radio).

1. Arrange the antenna, EUT, and the EMC analyzer as shown

in Figure 11. Separate the antenna and the EUT by 3 meters
(10 meters if it is called out in the regulation. If space is limited,
correct the results for the difference in distance from 3 to 10
meters which is 10.45 dB). It is important that the antenna is
not placed in the “near field” which is λ/2π away from the EUT
or closer.
 16

Radiated EMI: Layout

Equipment Under
Test
8590EM Series
EMC Analyzer

INPUTS OUTPUTS

LINE
OFF ON

HP 8447F
Preamplifier

G r o u n d P l a n e

Figure 11. Radiated emissions test setup.

2. Setup the EMC analyzer for the correct span, antenna correction
factors, and limit line with a margin. Load in the appropriate
limit line using the following steps:

Press [SETUP], <more>, <Limit Lines>, and <RECALL

LIMIT].

Scroll down to the radiated emissions limit determined in

Table 1 (i.e., FCC15B3M).

Press <LOAD FILE>

3. To load the appropriate antenna correction factor, first

determine the test frequency band. The HP 8590EM series has
two preset radiated emissions test bands, 30 MHz to 300 MHz
and 200 MHz to 1 GHz. The 30 MHz to 300 MHz band uses a
biconical antenna and the 200 MHz to 1 GHz uses a log periodic
antenna. There is also a broadband antenna (HP 11966P), that
covers both bands.

Press [SETUP], <more>, <Correctn Factor>,

<Antenna Factors>, <RECALL <ANTENNA>.

Scroll down to the antenna you wish to use using the knob or the
up/down arrows.

Press <LOAD FILE>

 17

Typical antenna factors are now loaded into the EMC analyzer.
The display is now corrected for the loss of the antenna and the
level is measured in dBuV/m which is a field strength measure-
ment. (See Appendix B for more information on field strength.)

4. If an amplifier is used between the antenna and the EMC analyzer

to improve sensitivity, correction factor for the amplifier also must
be loaded in the analyzer. To do this, press

[SETUP], <more>, <Correctn Factor>, <Other Factor>,

<RECALL OTHER>

Scroll to 8447HI and press <LOAD FILE>.

Your display should look similar to Figure 12.

Figure 12. Display with limit line and correction factors.

4.6 Measuring Radiated Emissions

Now you can start evaluating the radiated emissions your product
produces.
With the EUT off, sweep the frequency range of interest to survey
ambient environment levels. The ideal situation would be to have
all the ambient signals below the limit line. In many cases, ambient
signals will be above the limit, so you should measure them and
place the results in the internal list of the EMC analyzer.

4.7 Ambient Signal Measurements

The process for measuring the ambient signals is as follow:

1. Perform a maximum hold on the signals in the band by pressing

the following:

[TRACE], <MAX HOLD A>

(This function captures most signals including low PRF signals)

 18

2. Turn “WINDOW” function on by pressing [ON] under the

[WINDOWS ] area.

3. Adjust the <ZONE SPAN> with the knob to display no more

than 20 signals above the limit line on the bottom active trace.

4. Use the “automeasure” function to automatically measure the

signals above the limit line.

Press [TEST], <More>, <More>, <AUTOMEASURE>.

At this point, the EMC analyzer is performing peak and quasi-peak

measurements on all signals above the limit line. The signals
measured are the ambients (signals produced by other sources)
with EUT off. These signals are placed in the internal list. Move
the zone marker to the next group of signals on the top trace
using the <ZONE CENTER> function and repeat the automatic
measurements in Step 4 above. Make sure that all the signals that
are above the limit on the upper broad span trace are measured.
Press [ON] under the WINDOW area to view the menu with
<ZONE CENTER>. Press <ZONE CENTER> and use the knob
to move the zone marker to the next group of signals and repeat
Step 4 above.

4.8 Placement of EUT for Maximum Signals

Radiated emissions from electronic devices are not uniform. The

strongest emissions may be from the rear panel or front panel or
slots in the shielding. To ensure that you are measuring the worst
case emissions from your device, do the following:

1. Press [SETUP] and the frequency band of your antenna (i.e.,

<30 to 300 MHz> for a biconical antenna).

2. At each 45-degree step, note the amplitude of the largest signals.

(A screen output to a printer can be very useful. With a printer
connected to the IO port, press [COPY].)

3. On each screen output, mark the position of the EUT.

After all the screens have been captured, compare them to find the
position of the worst case emissions. In some cases, you may find
that there are worst case emissions for different frequencies at
different positions. For example, 100 MHz may be worst case
emissions at 90 degree and 200 MHz may be worst case emissions
at 270 degrees. In this case, the emissions tests must be performed
at both positions. A typical screen output is shown in Figure 13.
 19

If you are not sure whether the signal you are looking at is an
ambient or EUT signal, switch the power off on the EUT. If the
signal remains, then it is an ambient signal. Repeat this process
for the other polarization of the antenna (i.e., vertical or horizontal).

Figure 13. Radiated emissions display.

4.9 Ambient Plus EUT Measurements

With the EUT turned on and oriented to the worst case position,
perform automated tests again as shown below.

1. Press [NEXT] under [WINDOW] (This activates the

upper trace to capture the additional emissions from the
EUT.) Press [NEXT] again to activate the lower window.

2. Adjust the <ZONE SPAN> with the knob to display no

more than 20 signals above the limit line on the bottom
active trace. This gives the best frequency accuracy.

3. Use the auto measure function to automatically measure

the signals above the limit line (above the margin if it was
initiated).

Press [TEST], <More>, <More>, <AUTOMEASURE>.

At this point, the EMC analyzer is performing a peak and quasi-

peak on all signals above the limit line or margin which is within
the zone span area. If necessary, move the zone span to the next
group of signals above the limit or margin and perform another
automeasure as in Step 2 above.

The signals measured are the ambients and the EUT signals. These
signals are also placed in the internal list. Now that you have the
ambient signals from the first test and the ambient signals plus the
EUT signals from the second group of tests. You can perform a sort
on the list looking for duplicates which will be the ambient signals.
 20

To remove the ambient signals from the measurement results,

perform the following:

Press [TEST], <More>, <EDIT LIST>, <Signal Marking>,

<Selectv Mark>,
<MARK ALL DUPLICAT>, and <DELETE MARKED>.
(See Figure 14)

Figure 14. Radiated emissions measurement list.

At this point, most of the ambient signals have been deleted from
your list. Some ambients may still be present in the internal list
because they appeared during only one of the automatic measure-
ments which means that they would not have had duplicate
signals and thus would not have been deleted.

The signals in the list are the peak and quasi-peak values of the
EUT emissions and remaining ambient signals. Next, find signals
that are above the limit. To do this first sort the list by quasi-peak
values with the highest levels at the top of the list:

Press [TEST], <More>, <EDIT LIST>, <Sort Signals>,

<SORT BY QP AMP>.

Next, switch the column on which indicates the value of the

quasi-peak measurement versus the limit line.

Press [TEST], <More>, <SIG LIST ON>

Press <VIEW ∆> until VIEW QP ∆ LIM 1 is indicated at the top

of the right column. (See Figure 15)
 21

Figure 15. Measurements list compared to limit.

4.10 Evaluating Measurement Results

If all the values in the right hand column of the internal list are
negative, the product emissions are below the limit and your
product passes the radiated emissions requirements and your
job is completed.

If some of the values are positive then the quasi-peak measure-

ments are above the quasi-peak limit and the product fails
radiated emissions measurements. To be sure that signals are not
ambients, each signal should be remeasured. Use the demodulation
function to listen to the signal. AM/FM demodulation is a good tool
to use to determine whether or not a signal is an ambient.

To listen to a signal do the following:

Press [TEST], <More>, <SIG LIST ON>

With the signal list on, highlight the signal of interest with
the up/down keys.

Press [DEMOD], <DEMOD ON>, <FM>.

Adjust the volume to listen to the signal. If the signal is a local

AM, FM, TV, or cellular phone you should be able to demodulate
and listen to the signal. The demodulation function will enable the
operator to hear the audio part of the transmission by dwelling at
the marker for a specified length of time (usually 500 msec).

If there is any doubt about the signal being an ambient or an EUT

signal, remove the power to the EUT and observe the signal. If the
signal remains, it is an ambient. Note: It may not be convenient
to remove the power from the EUT, so using the demodulation
function may be the preferred method of identifying ambients.
 22

If you have determined that a signal is an ambient, the next step

is to delete the signal.

Press [TEST], <More>, <EDIT LIST>, <Delete Signals>,

highlight the ambient signal to be deleted and press
<DELETE MARKED>.

After the ambient signals have been deleted from the list, the next
step is to develop a report.

4.11 Report Development

The end result of all the above testing is a report. The report is
used by the design engineer to correct any problems which is found
during the test process. You can assemble a report using the
[OUTPUT] functions. The contents of the report can include a list
of signals, graphical representation of the signals, and up to two
pages of text which can be generated using a common PC key
board which connects to the rear of the EMC analyzer. To create
the text, press the following:

[OUTPUT] and <EDIT ANNOTATN>

If unwanted text exists in the annotation area, press <CLEAR

ANNOTATN>. Type in the desired text for your report. You may
want to include the date, location of the testing, who performed the
tests, product description, design engineer, and to which regulatory
agency product is tested. Some general comments about the test
results is usually helpful. After the text development is completed,
press <EXIT EDIT>.

To define the report content press <Define Report>, then choose

the items you would like to have in the report. Your report can
include annotation, log graphics, linear graphics, instrument
settings, and signal list information. Examples of log graph and
linear graph are shown in Figures 16a and 16b on the following
page.
 23

Figure 16a. Linear graph

Figure 16b. Log graph

List definition is a separate category. To define the list press

<Define List> and choose the items to be included in the list such
as detector results, limit comparisons, correction factors used, and
show marked signals. With the printer attached, press <OUTPUT
REPORT>. All the items selected under report definition will be
printed sequentially.
 24

5.0 Problem Solving and

Trouble Shooting At this point, after the product is tested and the results are record-
ed and printed your product is either ready for full compliance
testing and production or it must go back to the bench for further
diagnosis and repair.

If the product needs further redesign, the following process is

recommended.

1. Connect the diagnostic tools as shown in the Figure 17 below.

2. From the report, locate the problem frequencies.

3. Use the probe to locate the source or sources of the problem

frequencies.

4. With the probe placed to give the maximum amplitudes, record

the results on a RAM card.

5. Make circuit changes as necessary to reduce the emissions.

6. Remeasure the circuit using the same settings as before.

7. Recall the previous measurement stored on the RAM card and

compare the results to the current measurement.

EMI Diagnostic Measurement Setup

HP 8591EM
EMC Analyzer

HP 8447F
Preamplifier
INPUTS OUTPUTS

LINE
OFF ON

Close-Field Probe Circuit Under Test

Figure 17. Diagnostics setup interconnection.

 25

5.1 Diagnostics Testing Setup

As with emissions testing, the EMC analyzer must be setup to

perform diagnostics testing. Corrections for the probe and amplifi-
er must first be loaded into the EMC analyzer. The HP 11945A
probe kit contains two probes one for the 9 kHz to 30 MHz fre-
quency range and one for the 30 MHz to 1 GHz frequency range.
Connect the probe for the appropriate frequency range and load
in the correction factors by pressing the following:

[SETUP], more, <Correctn factors>, <Antenna factors>,

and <RECALL ANTENNA>.

Scroll down to the probe number which was installed and

press <LOAD FILE>.

The next step is to load in the correction factors for the amplifier
by pressing the following:

[SETUP], more, <Correctn factors>, <Other factors>, and

<RECALL OTHER>.

Scroll down to the HP 8447F HI or LO depending on the

probe used a press <LOAD FILE>.

The EMC analyzer is now calibrated in dBµA/m which is magnetic

field strength units.

5.2 Problem Isolation

Using the report generated from the conducted and radiated

emissions test, tune the EMC analyzer to one of the problem
frequencies with narrow enough span to give adequate differentia-
tion between signals.

Move the close field probe slowly over the device under test.
Observe the display for maximum emissions as you isolate the
source of the emissions. After you have isolated the source of the
emissions, record the location and store the display to a card.
To store the display insert a formatted RAM card into the card
reader and press the following:

[SAVE/RECALL], <Save Card>, <more>, <Trace ->CARD>,

and <TRACE A>.

Select a register number (i.e., 5) and press [ENTER].

 26

Figure 18 below is the trace saved into register 5 on the RAM card.
The prefix name TRACE was generated using the “Change Prefix”
functions.

Figure 18. Isolated signal source display.

The next step is to make design changes to reduce the emissions.

This can be accomplished by adding or changing circuit compo-
nents, redesign the problem circuit, or add shielding.

After the redesign, remeasure the results comparing the old trace
before redesign to new trace by recalling the saved trace off the
card. To recall the trace in register 5 press the following:

[SAVE/RECALL], <Recall Card>, <more>, and <RECALL

TRACE>.

Scroll down to the trace you previously stored and press

<LOAD FILE>.

The trace is recalled into the TRACE B area in the VIEW mode.
The current trace is in TRACE A in the CLEAR WRITE mode.
Figure 19 below shows the active trace and the recalled trace.
 27

Figure 19. Emissions reduction comparison display.

As you can see from the delta marker measurement the new trace
after the product redesign is 10 dB below the previously stored
trace. There is a one-to-one correlation between changes is close
field measurements and changes in far field measurements. For
example if you note a 10 dB change in measurements made by a
close field probe you will note a 10 dB change when you perform a
far field measurement using an antenna and an EMC analyzer.

Conversely, if you find that the radiated emissions from your EUT
is failing a limit by 10 dB, then you will need to do some redesign
to reduce the emissions by at least 10 dB. A good indication that
you have accomplished your goal is to make a 10 dB change with
close field measurements.
 28

Appendix A
Line Impedance Stabilization
Network (LISN)
A1.0 Purpose of a LISN
A line impedance stabilization network serve three purpose:

1. The LISN isolates the power mains from the equipment

under test. The power supplied to the EUT must be as clean
as possible. Any noise on the line will be coupled to the EMC
analyzer and interpreted as noise generated by the EUT.

2. The LISN isolates any noise generated by the EUT from

being coupled to the power mains. Excess noise on the power
mains can cause interference with the proper operation of
other devices on the line.

3. The signals generated by the EUT are coupled to the

EMC analyzer using a high pass filter which is part of the
LISN. Signals which are in the pass band of the high pass
filter see a 50 Ω load which is the input to the EMC
analyzer.

A1.1 LISN Operation

The diagram in Figure A-1 below show the circuit for one side of
the line relative to earth ground.

Line Impedance Stabilization

Network (LISN)

From Power 50 µH To
Source EUT
0.1 µF To
1 µF
1000W Receiver or EMC Analyzer
(50 Ω)

Impedance
(ohms) 60
50
40
30
20
10
Frequency (MHz)
.01 .1 1 10 100

Figure A-1. Typical LISN circuit diagram.

 29

The 1 µF in combination with the 50 µH inductor is the filter that

isolates the mains from the EUT. The 50 µH inductor isolates the
noise generated by the EUT from the mains. The 0.1 µF couples
the noise generated by the EUT to the EMC analyzer or receiver.
At frequencies above 150 kHz, the EUT signals are presented with
a 50 Ω impedance.

The chart in Figure A-1 above represents the impedance of the

EUT port versus frequency.

A1.2 Types of LISNs

Types of LISNs
H V symmetric N
1/2
V V sy
V1

1 un mm
c etric
un

ri
et sy
sy

1/2
m m V sy
m

m m mm
sy
m

et etric
et

un ric
ric

V2
Ground V asymmetric V2 unsymmetric

V-LISN Vector Diagram

V-LISN: Unsymmetric emissions (line-to-ground)

-LISN: Symmetric emissions (line-to-line)
T-LISN: Asymmetric emissions (mid point line-to-line)

Figure A-2. Three different types of LISNs.

The most common type of LISN is the V-LISN. It measures the

unsymmetric voltage between line and ground. This is done for
both the hot and the neutral lines or for a three-phase circuit in a
“Y” configuration, between each line and ground. There are some
other specialized types of LISNs. A delta LISN measures the line
to line or symmetric emissions voltage. The T-LISN, sometimes
used for telecommunications equipment, measures the asymmetric
voltage, which is the potential difference between the midpoint
potential between two lines and ground.

A2.0 Transient Limiter Operation

The purpose of the limiter is to protect the input of the EMC

analyzer from large transients when connected to a LISN.
Switching EUT power on or off can cause large spikes generated
in the LISN.

The HP 11947A transient limiter incorporates a limiter, high pass

filter, and an attenuator. It can withstand 10 kW for 10 µsec and
has a frequency range of 9 kHz to 200 MHz. The high pass filter
reduces the line frequencies coupled to the EMC analyzer.
 30

Appendix B
Antenna Factors
B1.0 Field Strength Units

Radiated EMI emissions measurements measures the electric field.

The field strength is calibrated in dBµV/m. Field strength in
dBµV/m is derived from the following :

Pt = total power radiated from an isotropic radiator

PD = the power density at a distance r from the isotropic

radiator (far field).

PD = Pt /4πr2 R = 120πΩ

PD = E2/R

E2/R = Pt /4πr2

E = (Pt x 30)1/2 /r (V/m)

Far field* is considered to be >λ/2π

*Far field is the minimum distance from a radiator where the field
becomes a planar wave.

B1.1 Antenna Factors

The definition of antenna factors is the ratio of the electric field in

volts per meter present at the plane of the antenna versus the volt-
age out of the antenna connector. Note: antenna factors are not the
same as antenna gain.

Antenna Factors
Biconical Log Periodic
dB/m
@ 10m @ 1m
30

25

20

15

10

5
0 200 400 600 800 1000
Frequency, MHz

Linear Units: AF = Antenna Factor (1/m) AF = Ein

E = Electric Field Strength (V/m) V out
V = Voltage Output from Antenna (V)
Log Units: AF(dB/m) = E(dBµV/m) - V(dBµV)
E(dBµV/m) = V(dBµV) + AF(dB/m)

Figure B-1. Typical antenna factor shapes.

 31

B1.2 Types of Antennas Used for Commercial Radiated

Measurements

Biconical Antenna
(30 - 300 MHz)
Blah

Broadband Antenna Log Periodic Antenna

(30 - 1000 MHz) (200 - 1000 MHz)

Figure B-2. Antennas used in EMI emissions measurements.

There are three types of antennas used for commercial radiated

emissions measurements.

Biconical antenna: 30 MHz to 300 MHz

Log periodic antenna: 200 MHz to 1 GHz (The biconical

and log periodic overlap frequency)

Broadband antenna: 30 MHz to 1 GHz (Larger format

than the biconical or log periodic
antennas)
 32

Appendix C Basic Electrical Relationships

The decibel is used extensively in electromagnetic measurements.

It is the log of the ratio of two amplitudes. The amplitudes are in
power, voltage, amps, electric field units, and magnetic field units.

decibel = dB = 10 log (P2/P1)

Data is sometimes expressed in volts or field strength units.

In this case, replace P with V2/R.

If the impedances are equal, the equation becomes:

dB = 20 log(V2/V1)

A unit of measure used in EMI measurements is dBµV or dBµA.

The relationship of dBµV and dBm is as follows:

dBmV = 107 + PdBm

This is true for an impedance of 50Ω

Wave length (l) is determined using the following relationship:

λ = 3x108 / f (Hz) or λ = 300/f (MHz)

 33

Appendix D
Detectors Used in EMI
Measurements—Peak,
Quasi-Peak, and Average
D1.0 Peak Detector

Initial EMI measurements are made using the peak detector.

This mode is much faster than quasi-peak, or average modes of
detection. Signals are normally displayed on spectrum analyzers
or EMC analyzers in peak mode. Since signal measured in peak
detection mode always have amplitude values equal to or higher
than quasi-peak or average detection modes, it is a very easy
process to take a sweep and compare the results to a limit line.
If all signals fall below the limit, then the product passes and no
further testing is needed.

D1.2 Peak Detector Operation

The EMC analyzer has an envelope or peak detector in the IF

chain which has a time constant such that the voltage at the
detector output follows the peak value of the IF signal at all
times. In other words, the detector can follow the fastest possible
changes in the envelope of the IF signal, but not the instanta-
neous value of the IF sine wave. (See Figure D-1)

Output of the Envelope Detector

Follows the Peaks of the IF Signal

Figure D-1. Peak detector diagram.

 34

D2.0 Quasi-Peak Detector

Most radiated and conducted limits are based on quasi-peak

detection mode. Quasi-peak detectors weighs signals according to
their repetition rate, which is a way of measuring their annoyance
factor. As the repetition rate increases, the quasi-peak detector
does not have time to discharge as much resulting in a higher
voltage output. (See Figure D-2 below.) For continuous wave (CW)
signals the peak and the quasi-peak are the same.

Since the quasi-peak detector always gives a reading less than or

equal to peak detection, why not use quasi-peak detection all the
time? Won’t that make it easier to pass EMI tests? Its true that
you can pass the tests easier, however, quasi-peak measurements
are much slower by 2 or 3 orders of magnitude compared to using
the peak detector.

Quasi-Peak Detector Output

Varies with Impulse Rate

Quasi-Peak Quasi-Peak
Peak Response Detector Reading Detector Response

Test Limit

Test Limit

Figure D-2. Quasi-peak detector response diagram.

D2.1 Quasi-Peak Detector Operation

The quasi-peak detector has a charge rate much faster than the
discharge rate therefore the higher the repetition rate of the sig-
nal the higher the output of the quasi-peak detector. The quasi-
peak detector also responds to different amplitude signals in a
linear fashion. High amplitude low repetition rate signals could
produce the same output as low amplitude high repetition rate
signal.
 35

D3.0 Average Detector

The average detector is required for some conducted emissions

tests in conjunction with using the quasi-peak detector. Also,
radiated emissions measurements above 1 GHz are performed
using average detection. The average detector output is always
less than or equal to peak detection.

D3.1 Average Detector Operation

Average detection is similar in many respects to peak detection.

Figure D-3 below shows a signal that has just passed through the
IF and is about to be detected. The output of the envelope detector
is the modulation envelope. Peak detection occurs when the post
detection bandwidth is wider than the resolution bandwidth.
For average detection to take place, the peak detected signal
must pass through a filter whose bandwidth is much less than the
resolution bandwidth. The filter averages the higher frequency
components, such as noise, at the output of the envelope detector.

Average Detection
A

Envelope Detector

Filters

Average Detector

Figure D-3. Average detection response diagram.

 36

Appendix E
EMC Regulatory Agencies The following is a listing of address and phone numbers for obtain-
ing EMC regulation information.

IEC
CISPR
Sales Department of the Central Office of the IEC
PO Box 131
3, Rue de Verembe
1121 Geneva 20, Switzerland

CCIR
ITU, General Secretariat, Sales Service
Place de Nation
1211 Geneva, Switzerland

Australia
Australia Electromechanical Committee
Standards Association of Australia
PO Box 458
North Sydney N.S.W. 2060
Telephone: +61 2 963 41 11
Fax: +61 2 963 3896

Belgium
Comite Electrotechnique Belge
3 Galerie Ravenstein, Boite 11
B-1000 Bruxelles
Telephone: +32 2 512 00 28
Fax: +32 2 511 29 38

Canada
Standards Council of Canada
Standards Sales Division
350 Sparks Street, Suite 1200
Ottawa, Ontario K1P 6N7
Telephone: 613 238 3222
Fax: 613 995 4564

Canadians Standards Association (CSA)

178 Rexdale Boulevard
Rexdale (Toronto), Ontario MSW 1R3
Telephone: 416 747 4044
Fax: 416 747 2475

Denmark
Dansk Elektroteknisk Komite
Strandgade 36 st
DK-1401 Kobenhavn K
Telephone: +45 31 57 50 50
Fax: +45 31 57 63 50
 37

France
Comite Electrotechnique Francais
UTE CEdex 64
F-92052 Paris la Defense
Telephone: +33 1 47 68 50 20
Fax: +33 1 47 89 47 75

Germany
VDE CERLAG GmbH
Austieferungsstelle
Merianstrasse 29
D-6050 OFFENBACH a.M.
Telephone: + 49 69 8306-1
Fax: + 49 69 83 10 81

India
Bureau of Indian Standards, Sales Department
Manak Bhavan
9 Bahadur Shah Zafar Marg.
New Delhi 110002
Telephone: + 91 11 331 01 31
Fax: + 91 11 331 40 62

Italy
Cometato Eletrotecnico Italiano
Viale Monza 259
1-20126 Milano MI
Telephone: + 39 2 25 77 31
Fax: + 39 2 25 773 222

Japan
Japanese Standards Association
1-24 Akasaka 4
Minato-Ku
Tokyo 107
Telephone: + 81 3 583 8001
Fax: + 81 3 580 14 18

Netherlands
Nederlands Normalisatie-Instituut
Afd. Verdoop en Informatie
Kalfjeslaan 2, PO Box 5059
2600 GB Delft
NL
Telephone: + 31 15 69 03 90
Fax: + 31 15 69 01 90

Norway
Norsk Elektroteknisk Komite
Harbizalleen 2A
Postboks 280 Skoyen
N-0212 Oslo 2
Telephone: + 47 2 52 69 50
Fax: + 47 2 52 69 61
 38

South Africa
South African Bureau of Standards
Electronic Engineering Department
Private Bag X191
Pretoria
0001 Republic of South Africa

Spain
Comite Nacional Espanol de la CEI
Francisco Gervas 3
E-28020 Madrid
Telephone: + 34 1 270 44 00
Fax: + 34 1 270 28 55

Sweden
Svenka Elecktriska Kommissionen
PO Bow 1284
S-164 28 Kista-Stockholm
Telephone: + 48 8 750 78 20
Fax: + 46 8 751 84 70

Switzerland
Swiss Electromechanical Committee
Swiss Electromechanical Association
Seefeldstrasse 301
CH-8008 Zurich
Telephone: + 41 1 384 91 11
Fax: + 41 1 55 14 26

United Kingdom
British Standards Institution
BSI Sales Department
Linford Wood
Milton Keynes MK14 GLE
Telephone: +44 908 22 00 22
Fax: +44 908 32 08 56

British Defence Standards

DEF STAN
Ministry of Defence
Northumberland House
Northumberland Ave
London WC2N 5 BP
Telephone: + 01 218 9000

United States of America

America National Standards Institute Inc.
Sales Dept.
1430 Broadway
New York, NY 10018
Telephone: 212 642 49 00
Fax: 212 302 12 86
 39

FCC Rules and Regulations

Technical Standards Branch
2025 M Street N.W.
MS 1300 B4
Washington DC 20554
Telephone: 202 653 6288

FCC Equipment Authorization Branch

7435 Oakland Mills Road
MS 1300-B2
Columbia, MD 21046
Telephone: 301 725 1585
 40

Glossary of Acronyms Ambient Level

and Definitions
1. The values of radiated and conducted signal and noise existing
at a specified test location and time when the test sample is not
activated.

2. Those levels of radiated and conducted signal and noise existing

at a specified test location and time when the test sample in inop-
erative. Atmospherics, interference from other sources, and circuit
noise, or other interference generated within the measuring set
compose the ambient level.

Amplitude Modulation

1. In a signal transmission system, the process, or the result of the

process, where the amplitude of one electrical quantity is varied in
accordance with some selected characteristic of a second quantity,
which need not be electrical in nature.

2. The process by which the amplitude of a carrier wave is varied

following a specified law.

Anechoic Chamber

1. A shielded room which is lined with radio absorbing material to

reduce reflections from all internal surfaces. Fully lined anechoic
chambers have such material on all internal surfaces: wall ceiling
and floor. Its also called a “fully anechoic chamber”. A semi-ane-
choic chamber is a shielded room which has absorbing material on
all surfaces except the floor.

Antenna (Aerial)

1. A means for radiated or receiving radio waves.

2. A transducer which either emits radio frequency power into

space from a signal source or intercepts an arriving electromagnet-
ic field, converting it into an electrical signal.

Antenna Factor
The factor which, when properly applied to the voltage at the input
terminals of the measuring instrument, yields the electric field
strength in volts per meter and a magnetic field strength in
amperes per meter.

Antenna Induced Voltage

The voltage which is measured or calculated to exist across the
open circuited antenna terminals.

Antenna Terminal Conducted Interference

Any undesired voltage or current generated within a receiver,
transmitter, or their associated equipment appearing at the anten-
na terminals.
 41

Auxiliary Equipment
Equipment not under test that is nevertheless indispensable for
setting up all the functions and assessing the correct performance
of the EUT during its exposure to the disturbance.

Balun
A balun is an antenna balancing device, which facilitates use of
coaxial feeds with symmetrical antenna such as a dipole.

Broadband emission
Broadband is the definition for an interference amplitude when
several spectral lines are within the RFI receivers specified band-
width.

Broadband Interference (Measurements)

A disturbance that has a spectral energy distribution sufficiently
brad, so that the response of the measuring receiver in use does
not vary significantly when tuned over a specified number of
receiver bandwidths.

Conducted Interference
Interference resulting from conducted radio noise or unwanted sig-
nals entering a transducer (receiver) by direct coupling.

Cross Coupling
The coupling of a signal from one channel, circuit, or conductor to
another, where it becomes an undesired signal.

Decoupling Network
A decoupling network is an electrical circuit for preventing test-sig-
nals which are applied to the EUT from affecting other devices,
equipment, or systems that are not under test. IEC 801-6 states
that the coupling and decoupling network systems can be integrat-
ed in one box or they can be in separate networks.

Dipole
1. An antenna consisting of a straight conductor usually not more
than a half-wavelength long, divided at its electrical center for con-
nection to a transmission line.

2. Any one of a class of antennas producing a radiation pattern

approximating that of an elementary electric dipole.

Electromagnetic Compatibility (EMC)

1. The capability of electronic equipment of systems to be operated

within a defined margins in of safety in the intended operational
environment at designed levels of efficiency without degradation
due to interference.

2. EMC is the ability of equipment to function satisfactorily in its

electromagnetic environment without introducing intolerable dis-
turbances into that environment or into other equipment.
 42

Electromagnetic interference
Electromagnetic interference is the impairment of a wanted elec-
tromagnetic signal by an electromagnetic disturbance.

Electromagnetic wave
The radiant energy produced by the oscillation of an electric
charge characterized by oscillation of the electric and magnetic
fields.

Emission
Electromagnetic energy propagated from a source by radiation or
conduction.

Far Field
The region where the power flux density from an antenna approx-
imately obeys an inverse squares law of the distance. For a dipole
this corresponds to distances greater than l/2 where l is the wave
length of the radiation.

Ground Plane
1. A conducting surface of plate used as a common reference point
for circuit returns and electric or signal potentials.

2. A metal sheet or plate used as a common reference point for

circuit returns and electrical or signal potentials.

Immunity

1. The property of a receiver or any other equipment or system

enabling it to reject a radio disturbance.

2. The ability of electronic equipment to with stand radiated elec-

tromagnetic fields without producing undesirable responses.

Intermodulation
Mixing of two or more signals in a nonlinear element, producing
signals at frequencies equal to the sums and differences of inte-
gral multiples of the original signals.

Isotropic
Isotropic means having properties of equal values in all directions.

Monopole
An antenna consisting of a straight conductor, usually not more
than one-quarter wave length long, mounted immediately above,
and normal to, a ground plane. It is connected to a transmissions
line at its base and behaves, with its image, like a dipole.

Narrowband Emission
That which has its principal spectral energy lying within the
bandpass of the measuring receiver in use.
 43

Open Area
A site for radiated electromagnetic interference measurements
which is open flat terrain at a distance far enough away from
buildings, electric lines, fences, trees, underground cables, and pipe
lines so that effects due to such are negligible. This site should
have a sufficiently low level of ambient interference to permit test-
ing to the required limits.

Polarization
A term used to describe the orientation of the field vector of a radi-
ated field.

Radiated Interference
Radio interference resulting from radiated noise of unwanted sig-
nals. Compare radio frequency interference below.

Radiation
The emission of energy in the form of electromagnetic waves.

Radio Frequency Interference

RFI is the high frequency interference with radio reception. This
occurs when undesired electromagnetic oscillations find entrance
to the high frequency input of a receiver or antenna system.

RFI Sources
Sources are equipment and systems as well as their components
which can cause RFI.

Shielded Enclosure
A screened or solid metal housing designed expressly for the pur-
pose of isolating the internal from the external electromagnetic
environment. The purpose is to prevent outside ambient electro-
magnetic fields from causing performance degradation and to pre-
vent emissions from causing interference to outside activities.

Stripline
Parallel plate transmission line to generate an electromagnetic
field for testing purposes.

Susceptibility
Susceptibility is the characteristic of electronic equipment that
permits undesirable responses when subjected to electromagnetic
energy.
For more information about
Hewlett-Packard test and measure-
ment products, applications, ser-
vices, and for a current sales
office listing, visit our web site,
http://www.hp.com/go/tmdir. You
can also contact one of the following
centers and ask for a test and
measurement sales representative.

United States:
Hewlett-Packard Company
Test and Measurement Call Center
P.O. Box 4026
Englewood, CO 80155-4026
1 800 452 4844
Canada:
Hewlett-Packard Canada Ltd.
5150 Spectrum Way
Mississauga, Ontario
L4W 5G1
(905) 206 4725
Europe:
Hewlett-Packard
European Marketing Centre
P.O. Box 999
1180 AZ Amstelveen
The Netherlands
(31 20) 547 9900
Japan:
Hewlett-Packard Japan Ltd.
Measurement Assistance Center
9-1, Takakura-Cho, Hachioji-Shi,
Tokyo 192, Japan
Tel: (81-426) 56-7832
Fax: (81-426) 56-7840
Latin America:
Hewlett-Packard
Latin American Region Headquarters
5200 Blue Lagoon Drive, 9th Floor
Miami, Florida 33126, U.S.A.
(305) 267 4245/4220
Australia/New Zealand:
Hewlett-Packard Australia Ltd.
31-41 Joseph Street
Blackburn, Victoria 3130, Australia
1 800 629 485
Asia Pacific:
Hewlett-Packard Asia Pacific Ltd.
17-21/F Shell Tower, Times Square,
1 Matheson Street, Causeway Bay,
Hong Kong
Tel: (852) 2599 7777
Fax: (852) 2506 9285

Data Subject to Change

Copyright © 1997
Hewlett-Packard Company
Printed in U.S.A. 4/97
5964-2151E