Scribd
Upload
133 views

DTMF Discussion

DTMF signals are composed of two tones that are decoded by controllers. If the DTMF decoder is not working properly, measurements can help determine the cause. The tones fall within specific frequency bands, and the signal level must be around 220mV for reliable decoding. Issues like signal twist, where one tone is attenuated more than the other, can also impact decoding if not properly addressed. The decoder separates the tones and filters them for identification by the microprocessor.

Uploaded by

ismifaizul
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
133 views

DTMF Discussion

DTMF signals are composed of two tones that are decoded by controllers. If the DTMF decoder is not working properly, measurements can help determine the cause. The tones fall within specific frequency bands, and the signal level must be around 220mV for reliable decoding. Issues like signal twist, where one tone is attenuated more than the other, can also impact decoding if not properly addressed. The decoder separates the tones and filters them for identification by the microprocessor.

Uploaded by

ismifaizul
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

CAT PAPER

CAT Paper: P-4

Page 1

Discussion about DTMF Decoding

All of the CAT controllers use DTMF decoders and is a vital component in operating and controlling any repeater. If the DTMF decoder becomes inoperative or is not working at all, several signals, voltages, etc., can be measured in determining how the DTMF problem can be corrected.

A Look At The DTMF Signal


DTMF generation is a composite audio signals of two tones between the frequency of 697Hz and 1633Hz. The DTMF keypad is arranged such that each row will have its own unique tone frequency and also each column will have its own unique tone. Below is a representation of the typical DTMF keypad and the associated row/column frequencies.
High Tone Group

1209 Hz 1336 Hz 1477 Hz 1633 Hz 697 Hz


Low Tone Group

1 4 7

2 5 8 0

3 6 9 #

A B C D

770 Hz

852 Hz

941 Hz

By pressing a key, for example 5, will generate a dual tone consisting of 770 Hz for the low group, and 1336 Hz of the high group.

Computer Automation Technology, Inc. Fort Lauderdale, Florida (954) 978-6171

CAT PAPER

CAT Paper: P-4

Page 2

Discussion about DTMF Decoding

The tone frequencies were selected such that harmonics and intermodulation products will not cause an unreliable signal. The decoders used in the CAT controllers have a digital low/ high tone decoder with frequency passband as follows:
Low Tone Group High Tone Group

697 Hz

770 Hz

852 Hz

941 Hz

1209 Hz

1336 Hz

1477 Hz

1633 Hz

685 709

756 784

837 867

925 957

1189 1229

1314 1358

1453 1501

1607 1659

As the above frequency spectrum illustrates, each tone must fall within the proper bandpass before a valid decode will take place. If one, or both tone(s) falls outside the spectrum bandpass, the decoder will operate erratic becoming unreliable or not operate at all.

Signal Input Levels


Another important requirement for reliable decoding is the signal level applied to the decoder audio input. The manufacture rates the dynamic range as from -26 dBm to +2 dBm. However, when the decoder is used across a radio link, the level input needs to be adjusted with care. After careful study and field testing, 220 mVAC at the decoder input proved to provide the best input level. This is why audio level adjustments when installing a CAT controller calls for the decoder level input adjusted first for a solid input to the decoder of 220 mVAC.

Computer Automation Technology, Inc. Fort Lauderdale, Florida (954) 978-6171

CAT PAPER

CAT Paper: P-4

Page 3

Discussion about DTMF Decoding

Twist, what is it?


Twist is known as the difference in signal levels between the two tones. If a DTMF tone applied to the decoder IC has equal low and high tone amplitudes, the twist is equal to zero. However in communication links, were the DTMF signal is amplified and possible filtered in the radio receiver, twist can become a concern because the frequency response of that receiver is not flat. Usually the higher frequency tone group will be attenuated resulting in the higher DTMF keys A, B, C, and the D key becoming effected whereas the other keys are working OK. Remember also that the transmitting DTMF signal can also have some twist resulting in some handy talkies working OK while others are not. If you suspect twist to be a problem, youll need to first find out if the problem is transmitted twist. That is, make sure your transmitted signal is flat before you proceed to the receiver. If the twist is being generated in the receiver, an oscilloscope will be your best piece of test equipment to trace down were the problem is. Using the receivers schematic, begin at the FM discriminator and make measurements with each tone group. Once you have your base measurements (and have determined they look OK with no twist), move your scope probe along the receiver signal path and look for any signal degradation. If your taking your receiver signal off of the speaker for example, now would be the time to move your signal pick-off point ahead of the audio output amplifiers. You will notice not only an improvement or removal of twist, but usually the audio quality will be improved.

Microprocessor Interface
Once the DTMF signal has been applied, internal interfacing circuits must first separate the two tones into two discrete tones, one from the low group and the other from the high group.
High Group Filters

Digital Filter Received Data Register

Audio Input
Low Group Filters Digital Filter

Computer Automation Technology, Inc. Fort Lauderdale, Florida (954) 978-6171

CAT PAPER

CAT Paper: P-4

Page 4

Discussion about DTMF Decoding

Once separated, the signals are applied to two digital filters to decode the exact tone. Since the digital filters operate with internal clock signals, it is necessary to have some sort of clock standard (accurate and stable) to insure consistant filtering and decoding. The clock source for these decoders is an external color burst crystal (3.5795 Mhz) connected between the OSC1 and OSC2 integrated circuit pins. Measurement of the internal clock signal can be made with an oscilloscope connected to the OSC2 pin of the integrated circuit to determine if the clock signal is satisfactory. (Use X10 probe)

MT-8870 4.8 VAC MT-8880 MT-8888 279.3 ns

Pin 8 Pin 7 Pin 7

MT-8870 In + In GS Vref Inh Pwdn Osc1 Osc2 Vss 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 Vdd St/Gt Strobe Std D3 D2 D1 D0 TOE In + In GS Vref Vss Osc1 Osc2 Tone Out R/W CS

MT-8880 / 8888 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 Vdd St/Gt Strobe D3 D2 D1 D0 IRQ Clk RS0

Top View

Top View

Computer Automation Technology, Inc. Fort Lauderdale, Florida (954) 978-6171

CAT PAPER

CAT Paper: P-4

Page 5

Discussion about DTMF Decoding

Next the microprocessor needs to be signaled that a valid DTMF tone has arrived. The decoder accomplishes this by a signal output from the decoder called STROBE. That signal can be monitored by an oscilloscope to determine if the microprocessor is being told a signal has arrived. For the different decoder devices used in the CAT controllers, the pin numbers for the stobe signal are: MT-8870 MT-8880 MT-8888 Pin 15 Pin 18 Pin 18

While having your scope probe connected to the strobe pin, apply a signal into the receiver and modulate it with DTMF tones. For each tone you press, the strobe line should increase from near zero volts, to a voltage between 4.5 to 5.0 VDC. Try all of the 16 DTMF tones to insure that all of them are decoding satisfactorly. Remember, if the strobe line does not respone to DTMF inputs, then a problem with the audio input needs to be investigated.

DTMF Signal In

Strobe

Computer Automation Technology, Inc. Fort Lauderdale, Florida (954) 978-6171

CAT PAPER

CAT Paper: P-4

Page 6

Discussion about DTMF Decoding


Freq Low Freq High D3 D2 D1 D0

Digit

1 2 3 4 5 6 7 8 9 0

697 697 697 770 770 770 852 852 852 941 941 941 697 770 852 941

1209 1336 1477 1209 1336 1477 1209 1336 1477 1336 1209 1477 1633 1633 1633 1633

0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0

0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0

0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0

1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

*
# A B C D

Computer Automation Technology, Inc. Fort Lauderdale, Florida (954) 978-6171

You might also like