Weekend

Garden
Projects

2000 by Rodale Inc.

Enjoy Gingerbread in the Garden (page 9), Erect a Rustic Trellis (12), Construct a Simple Arbor (13), Visualize a Gardens View of the Moon (16), Create a Garden Gazing Globe (18), Make a Mosaic Tabletop (19), Put Together a Picket Planter (24) and Form a Frugal Potting Bench (35) are excerpted from The Frugal Gardener by Catriona Tudor Erler, 1999 by Catriona Tudor Erler . Used with permission of Rodale Inc . Add a Water FeatureWithout the Water (page 43) and Create a Small Pond (46) are excerpted from Jeff Coxs 100 Greatest Garden Ideas by Jeff Cox, 1998 by Jeff Cox . Used with permission of Rodale Inc . Build a Butterbean Tent (page 7), Make a Flower Press (27), Design a Scarecrow (31), Construct Your Own Planting Flats (33), and Build a Rock-Wall Herb Garden (38) are excerpted from 52 Weekend Garden Projects by Nancy Bubel, 1992 by Nancy Bubel . Craft a Cornhusk Wreath (10), Assemble a Garlic Braid (21), and Put Up a Yule Log for the Birds (36) are excerpted from 52 Weekend Garden Projects 1993 by Nancy Bubel, 1993 by Nancy Bubel . Used with permission .

credits

contents
Extend Your Gardening Pleasure . . . . . . . . . . . .4 Eye-Catching Creations . . . . . . . . . . . . . . . . . . .5
Whittle Willow Edgings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Build a Butterbean Tent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Enjoy Gingerbread in the Garden . . . . . . . . . . . . . . . . . . . . . . . 9 Craft a Cornhusk Wreath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Erect a Rustic Trellis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Construct a Simple Arbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Visualize a Gardens View of the Moon . . . . . . . . . . . . . . . . . . 16 Create a Garden Gazing Globe . . . . . . . . . . . . . . . . . . . . . . . . 18 Make a Mosaic Tabletop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fashion a Natural Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Assemble a Garlic Braid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Put Together a Picket Planter . . . . . . . . . . . . . . . . . . . . . . . . . . 24

To order Nancy Bubels The New Seed-Starters Handbook, call (800) 848-475.

The information in this book has been carefully researched, and all efforts have been made to ensure accuracy. Rodale Inc. assumes no responsibility for any injuries suffered or damages or losses incurred during use of or as a result of following this information. It is important to study all directions carefully before taking any action based on the information and advice presented in this book. When using any commercial product, always read and follow label directions. If trade names are used, no discrimination is intended and no endorsement by Rodale Inc. is implied.

Projects to Get the Job Done . . . . . . . . . . . . . .26

Create a Sunflower Seed Catcher . . . . . . . . . . . . . . . . . . . . . . 26 Make a Flower Press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Design a Scarecrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Construct Your Own Planting Flats . . . . . . . . . . . . . . . . . . . . 33 Form a Frugal Potting Bench . . . . . . . . . . . . . . . . . . . . . . . . . 35 Put Up a Yule Log for the Birds . . . . . . . . . . . . . . . . . . . . . . . 36

Stone Elegance . . . . . . . . . . . . . . . . . . . . . . . . .38

Director: K. Greenslade Project editor: Kerry K. Callahan Copy editor: Mary Ellen B. Raposa Cover designer: Barb Sheetz Book designer: Cheryl V Dorschutz .

Build a Rock-Wall Herb Garden . . . . . . . . . . . . . . . . . . . . . . . 38 Add a Water FeatureWithout the Water . . . . . . . . . . . . . . . . 43 Create a Small Pond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

extend your gardening pleasure

eye-catching creations
Whittle WilloW edgings
Add nAturAl chArm to your gArden with A do-it-yourself edging
dgings are picture frames for your landscape . They accent individual sections and help tie sections together into a unified whole . They also reduce mowing and trimming by preventing lawn grass from creeping into your perennials and by giving you a clean edge to trim up to .

t
4

here are more creative ways to enhance the appearance of your garden than simply selecting the healthiest, most attractive plants . This book brings you a range of beautiful, practical, and fast projects for in and around your garden . We know youd rather spend time enjoying the beauty and bounty of your garden, instead of working on lengthy projects that keep you out of it . So, spend just one weekend building your butterbean tent, flower press, dry streambed, or any of the other 18 projects inside, and spend every weekend after that enjoying them . Or tackle a few projects during the bleakest winter weekends youll satisfy your garden fever and be ahead of the game when spring rolls around!

A decorative willow edging is fun to make and is also surprisingly durable. Be sure you choose green branches so theyre easy to weave.
MATEriAlS

18-inch-long willow branches Use green, flexible branches that bend easily. Long twigs Utility knife

TOOlS

WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 5

DirECTiONS

1 . Using the utility knife, strip the bark off the ends of your willow branches to prevent them from sprouting . Push 3 one end of a willow branch into the soil . Insert the other end about 6 inches away . Repeat along the entire edge, overlapping the arches . 2 . Weave four long twigs in and out around the bases of arches; push the ends into the soil . 3 . Weave a second band of four twigs near the top of the arches .

Build a ButterBean tent

creAte A childs speciAl summerhouse of greenery
ucky the child who can remember hiding out in a tent formed by bean vines and their poles! The buzzing warmth of a summer day, the small secret place, and the green of the sheltering vines blend in memories of that dreamlike world where days were long and summers endless . Heres how to treat your youngsters to the same adventure .
MATEriAlS

[1]

Three poles Twine or wire 1-inch-diameter stick 15 pole bean seeds

DirECTiONS

[2 and 3]

1 . To make a oneperson, three-pole tent, space poles 3-to 4 feet apart to form a circle . Allow a 2- to 3-foot gap between two poles for a doorway . Ram the thick end of each pole about 12 inches into the ground .

Children of all ages will love this shady, secret hideout.

WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 7

2 . Tie or wire the top ends of the poles together . 3 . Tie the 1-inch-diameter stick horizontally, a little lower than head height, between the two doorway poles . 4 . Plant five pole bean seeds at the bottom of each pole . Or, instead of traditional pole beans, you can try morning glories, climbing nasturtiums, moon vine, gourds, scarlet runner beans, or a mixture . If the seeds are planted in spring, the vines will form a leafy canopy by midsummer .

e n j oy g i n g e r B r e a d in the garden
scrolled gingerbreAd And A gAte combine for An instAnt gArden Accent

A Hideout Built for Two or More!

to make a roomier hideout that costs much less than a wooden playhouse, set poles in the ground in either a circular or a rectangular shape. (For a 5 X 7-foot structure, youll need about 18 poles.) Place two of them a bit farther apart than the others to form a doorway space. then, wire or staple wire-mesh poultry netting to the poles to form the walls of the structure, leaving space for the doorway. if you want a roof, tie strings across the top. Finally, plant seeds of any quick-growing vine at the base of each pole. the vines will transform the bare string and wire into a lovely, leafy teahouseephemeral but perfect.

he scrolled and curved woodwork or metal known as gingerbread adds a touch of Victorian gentility to many garden ornaments . Find the original at architectural salvage yards or demolition sites (always ask for permission first!), or dig up replicas at home supply stores or discount stores or in catalogs . Prices vary widely, so if you dont feel youre getting a bargain, shop around .
MATEriAlS

Gingerbread Nails Paint Paintbrush Hammer

TOOlS

DirECTiONS

Nail a piece of scrolled gingerbread to the top of a simple gate . Paint the fence and decoration to match, and it will look like a custom creation .

A piece of scrolled gingerbread makes an instant, charming addition to your garden.

WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 

C r a F t a C o r n h u s k W r e at h

mAke this decorAtive symbol of fAll in one fun evening

ried cornhusks are part of the mellow look of fall, along with pumpkins, gourds, autumn leaves, and Indian corn . Wreaths made out of cornhusks look great on doors or walls, either indoors or out, and theyre lightweight and long lasting . Heres how to make one that will give you years of pleasure .
MATEriAlS
Cornhusk strip 1 ( 5 8 " wide) 2

Wire wreath

Dried husks from 10 to 12 large ears of corn If you dont have a nearby cornfield where you can gather husks, look for them at craft shops or in a Spanish or Mexican grocery store. Damp towel or water basin Wire coat hanger Large, strong safety pin String Scissors Wire cutter Pliers

4 . Working with one strip at a time, bend the strip into a U shape . Lay the strip under the wire hoop, so that you can see the U shape and the two loose ends face the center of the hoop . Bring both the bent end and the loose ends up and over the wire hoop, insert both loose ends through the bent end, and then pull the two loose ends tightly to fasten the strip firmly to the wire . 5 . Continue to add cornhusk strips until the wire circle is entirely covered with them . Push the looped husks together as you work, cramming as many husks as possible onto the wire for maximum fullness .

TOOlS

Bend a thin strip of cornhusk into a U shape and place it under the wire with loose ends facing the wreath center. Bring both ends up and over the wire, inserting loose ends through the loop. Pull the ends outward firmly until the knot is tight.

1 . Using the scissors, cut the stem end from each husk, so that the individual leaves of the husk are separated and flat . Then, wrap the husks in a damp towel or soak them in a basin of lukewarm water for 20 to 30 minutes so theyll be more pliable and easier to work with . 2 . Pull the wire coat hanger open and bend it into a circle . You can leave the hook on to act as a hanger, camouflaging it later with a large bow . For a neater appearance, cut off the hook and rejoin the cut ends . Crimp the joined ends with the pliers so theyll stay together . 3 . Tear the wet cornhusks into strips about 12 to 58 inch wide . Most cornhusks are about 8 to 9 inches long . Small variations in length dont matter .
10 WEEKEND GARDEN PROJECTS

DirECTiONS

6 . When the wire is completely covered with looped husks and you cant fit any more on, fringe the husks, one husk strip at a time . To do this, grasp the safety pin at its joint . Poke the point of the pin into each husk near the loop, and draw the pin out to the loose end of the husk . Split each husk strip once or twice, creating thin strips about 1 4 inch or less wide . When the husks dry, they will curl up, giving the wreath an attractive tousled appearance . 7 . To complete the wreath, tie a short loop of string to the back of the wire for a hanger . If you wish, you can add a bow made of checked or calico fabric, raffia, burlap, or rope, and even a couple of miniature ears of corn, some dried flowers, or a few tendrils of bittersweet .

Add strips, pushing them together tightly as you work.The more strips you use, the fuller the wreath will look.
BACK TO CONTENTS 11

ereCt a rustiC trellis

Add AppeAl to your gArden with this nAturAl trellis

ConstruCt a simPle arBor

ou cant beat grapevines for lending a touch of rustic charm to any garden . Simply wrap grapevines around thick tree branches, and youll have a perfect place for lightweight climbers like morning glories or scarlet runner beans .
MATEriAlS

this Arbor mAkes A perfect gAtewAy into A speciAl section of your gArden
yard full of flowers can look like a flat sea of plants . To add height to your garden quickly and provide soothing shade in the long term, try building an arbor . Four 8-foot-long 2 4s (posts) Six 8-foot-long 1 3s One 5-foot-long 2 4 1 pound of 1-inch drywall screws 1 quart of paint or polyurethane One bucket of gravel One bag of quick-setting concrete

Two 4-inch-diameter branches (poles) Two 3-inch-diameter branches (poles) Nails Grapevines Hammer Staple gun

MATEriAlS

TOOlS

TOOlS DirECTiONS

1 . Use the 4-inchdiameter poles for the supporting sides, and nail on the 3-inch-diameter poles for the top and bottom crosspieces . 2 . Fill in the interior of the trellis with grapevines looped from side to side or with branched twigs arranged in a pleasing pattern . 3 . Secure the vines or twigs with heavyduty staples in the two side posts .

Pencil Tape measure Circular saw Power screwdriver or electric drill fitted with Phillips screwdriver bit Paintbrush Square

1 . Mark the 8-foot 2 4s with a pencil line at each of these intervals, measured from the bottom of the boards: 18, 24, 36, 48, 60, 72, 84, and 93 inches (the last mark should be about 3 inches from the top of the board) . Write the measurement at each mark . 2 . Mark and cut four of the 1 3s into 12 sections that are 30 inches long . Cut the 5-foot 2 4 into 2 sections that are 30 inches long . Staple grapevines in place to secure them. 3 . Lay two 8-foot 2 4s parallel, 30 inches apart . Screw a section of a 1 3 to a 2 4 at the 24-inch marking, using two

DirECTiONS

12 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 1

1 3 48"

drywall screws . Repeat at the markings for 36, 48, 60, 72, and 84 inches . Screw a 30-inch 2 4 at the 93-inch mark . 4 . Repeat Step 3 for the other set of 2 4s . 5 . Mark and cut each of the two remaining 1 3s into two 48-inch lengths .

6"

36"

6 . Attach the four sections of 48-inch-long 1 3s across the top of the arbor with drywall screws . Allow each board to overhang 6 inches on each side of the arbor, creating an arbor with a 36-inch opening . 7 . Paint or polyurethane the arbor . 8 . Set your arbor in the desired location and mark the locations of the four 2 4 30" posts . Move the arbor out of the way, and dig 2 12- to 24 3-foot-deep holes for the poles . (You can rent a posthole digger to make the 13 job easier .) 9 . Place a 6-inch layer of gravel in each hole . 10 . Stand the arbor in the holes with the pole sides square and length straight . Fill with quick-setting concrete and hold in place until the concrete sets .
6" 30"

Space the four 48-inch-long boards evenly across the top of the arbor, allowing for a 6-inch overhang on each side.

Dressing Your Arbor

once youve built your arbor, youre ready for the best part: dressing it in vines. its enchanting to see a tall structure in the garden smothered in flowering climbers, taking both color and drama up toward the sky. For strong structures, consider honeysuckle, climbing roses, clematis (mix varieties to get bloom from spring through late summer), wisteria, bougainvillea, and trumpet creeper. dont overlook edibles such as grapes and hardy kiwi vines. (But, if you want to sit under your arbor, remember that ripe fruit attracts bees and wasps.) if you used a lighter-weight wood that cant support much weight, stick to annual vines. morning glories, scarlet runner beans, climbing nasturtiums, and cardinal climber are all good choices.

Be sure to anchor your arbor securely in 2 12 - to 3-foot- deep holes, so it stays in place under the weight of vines or the force of the wind.

14 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 15

Visualize a gardens VieW oF the moon

Add An intriguing touch to A fence with A peephole for viewing the rising moon
his simple project can lend your garden a Victorian, Japanese, or even contemporary look . It all depends upon your fence style and paint color .
MATEriAlS

Cut off the excess; you dont want any strips to extend beyond the doughnut . 6 . Nail the plywood doughnuts around the circle of the lath, one on each side of the fence . Make sure that the lath is against the fence . 7 . Paint the fence .

Scrap plywood 12 lath strips, each 24 inches long Nails Paint Jigsaw Staple gun and heavy-duty staples Hammer Paintbrush

TOOlS

1 . Mark an 18-inch-diameter circle on a section of board fence . Place the circle so that it is at least 2 inches from any crosspieces . 2 . Saw out and remove the fencing from the circle . 3 . Measure and mark a 24-inch-diameter circle on the plywood, and then measure and mark a 16-inch-diameter circle inside of and concentric to the larger one . Cut out the plywood doughnut between the two marks . 4 . Repeat Step 3, so you have two plywood doughnuts . 5 . On one of the doughnuts, make a lattice design for the hole by attaching the lath strips across the face of the doughnut . Customize a plain board fence by adding a moon window of lattice for a view through the fence.

DirECTiONS

1 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 17

C r e at e a g a r d e n gazing gloBe
mAke A lovely gArden ornAment out of A simple fishbowl
f you have an old pedestal from a birdbath hiding in your garage or you find one at a garage sale, you can turn it into a stand for a gazing globe . The globe itself is just a glorified fishbowl, but no one will know by looking at it .
MATEriAlS

m a k e a m o s a i C ta B l e t o P
use broken pottery to trAnsform A tAble from ordinAry to extrAordinAry
ecycle an old metal snack table into an object of art by covering the surface of the tabletop with bits of pretty broken pottery, china, ceramic, or mirrors . If you dont have broken glass or china lying around, collect appealing colors and patterns of dishes at thrift shops and yard sales, slip them into a pillowcase, and whack lightly with a hammer to break them .
MATEriAlS

Round glass fishbowl Metallic spray paint Scrap plywood Pedestal-type birdbath base Aquarium glue Saw

Old metal table Tile adhesive Broken china, pottery, or glass Tile grout Putty knife Sponge

[1]

TOOlS TOOlS

DirECTiONS

1 . Spray the inside of the fishbowl with metallic paint in your favorite color .

DirECTiONS

2 . Invert the fishbowl onto a piece of scrap plywood and trace around the fishbowl opening . Cut out that circle . Then, cut a hole in the center of the plywood disk so that the top of the pedestal can protrude at least 1 inch . 3 . Slip the disk over the pedestal and then invert the bowl onto the disk . Use a touch of aquarium glue to hold the bowl securely in place .

Gaze into the future through this pretty, easy-to-make garden gazing globe.

1 . Cover a clean metal tabletop with a 12-inch-thick layer of tile adhesive, smoothing it with a putty knife . 2 . Arrange bits of broken pottery, china, or other decorative flat shards on the tabletop, pushing them into the adhesive so that all their sharp edges are covered . 3 . With the knife, apply tile grout over the tabletop, making sure all crevices are filled . Wipe off excess grout with a sponge . [2]

[3]
BACK TO CONTENTS 1

18 WEEKEND GARDEN PROJECTS

Fa s h i o n a n at u r a l ta B l e
turn A stump into A stAnd in one Afternoon
tree stump in your yard need no longer be a liability . Turn it into a natural table, and youll have a wonderful place to rest your drink, lay your book, or whatever strikes your fancy .
MATEriAlS

assemBle a garliC Braid

if you cAn brAid A pigtAil, you cAn mAke this AttrActive room Accent

Thick wood boards Nails Four crooked tree branches Saw Level Hammer

TOOlS

DirECTiONS

1 . Saw off the top of the tree stump until it is perfectly level .

2 . Nail the wood boards to the flat top of the stump . 3 . Nail the crooked branches to the lower part of the stump, so they support the wood top at the four corners .

garlic braid hanging in the kitchen is a wonderful symbol of abundance and good cookery . The plump bulbs with their tight satin-paper skins are pleasant to look at, even for those who dont actually eat a lot of garlic . Garlics reputation for protecting the household from vampires can make your garlic braid an amusing conversation piece, too . To use your garlic braid as a handy Youll need to start your dispenser of flavorful bulbs, simply braid by drying your summer harpeel off cloves as you need them. vest of garlic, with tops attached, on screens for a week or two .
MATEriAlS

16 well-rounded, shapely bulbs of garlic with strong tops A few feet of strong white string Scissors

TOOlS

The support branches should be in their natural state, complete with knots and crooked angles, as they add much to the enticing look of this natural table.

DirECTiONS

1 . Snip off the roots of the garlic bulbs as close as possible to the base of the bulbs, leaving only a short tuft of root threads . Then, rub the root stub with your thumb to dislodge any remaining soil . Do not wash the bulbsthey last longer if

20 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 21

theyre kept dry . Simply peel off the loose, dirty outer skin to reveal the clean, white wrapper underneath . 2 . Choose three bulbs with tops of different lengths, so that they wont all end at the same place in the braid . Arrange the garlic bulbs on your worktable side by side, with the bulb ends closest to you and the tops pointing away from you . Line them up so that the tops are even across the top and the bulbs are staggered . 3 . Cut a piece of strong white string about 6 inches longer than the garlic tops (about 30 inches, depending on the length of your tops) . Lay it next to one of the dried garlic tops, leaving the extra 6 inches of string extending at the upper end for a hanger . 4 . Cut a piece of string about 6 inches long . Use it to tie the three garlic tops and the long piece of string together, almost at the very top . The short piece of string will not be used in braiding . 5 . Begin braiding the garlic tops together, starting at the ends farthest from the bulbs . Always include the long string as though it were part of one of the garlic tops, to strengthen the braid . You may want to secure the upper end of the braid before you proceed by hanging it on a nail or placing a few books over it . If you can braid a pigtail, youll have no trouble making a simple garlic braid. Lap the tops of the bulbs, alternating right and left, and always include the long string as part of the braid. To braid, lap the top of the right bulb over the top of the middle bulb . Then, lap the top of the left bulb over the middle top (which used to be the right bulb top) . Try to braid with even ten-

sion on the tops, so the links are the same size and fit snugly next to each other . Continue alternating right and left until you get near the first bulb . 6 . As you get close to the bottom (bulb) end of each strand of garlic top, add another strand of garlic top (with a bulb on the other end of it), overlapping the two strands (old and new) by about 3 inches . 7 . Continue to braid until you have used up all the bulbs . Then, tie the braid together at the bottom with string . Make a loop in the string at the top, cut off any extra string, and hang . To make sure there are no bare spots in your braid, work in a new bulb as you need it, overlapping the old and new tops by about 3 inches.

long string 3 tops tied with short string

22 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 2

Put together a PiCket Planter

dress up your porch with A cottAge-gArden plAnter

2 . Build the planter box, nailing together the front, back, sides, and bottom . Drill 14- to 12-inch holes in the bottom for drainage . 3 . Attach front legs to the front of the box so that the bottom of the box is 2 feet above the bottom of the legs . The legs extend to the top of the box at the front corners . 4 . Attach the back legs to the box so that the bottom of the box is 2 feet above the bottom of the legs . The legs extend 18 inches above the back corners of the box . 5 . Attach the central picket to the box so its bottom is flush with the bottom of the box . 6 . Measure and attach other pickets equidistant between the central picket and back leg extensions . Make sure the angled tops are all going in the correct direction, with the highest side of the angle facing toward the center picket . 7 . Attach the horizontal support across the pickets, nailing it to the back leg extensions . 8 . Nail the top caps on the top of the back leg extensions . 9 . Paint the planter box, insert the window-box liner, and fill with soil mix and plants .

his charming planter looks great on an old-fashioned porch when filled with ferns and ivy or cheerful red geraniums . One 2-foot-long 1 3 (center picket) Two 20-inch-long 1 3s (pickets) Two 16-inch-long 1 3s (pickets) Two 12-inch-long 1 3s (pickets) Two 3-foot-long 2 6s (front and back) One 3-foot-long 2 12 (bottom of planter box) Nails Two 12-inch-long 2 6s (sides of planter box) Two 212-foot-long 2 4s (front legs) Two 4-foot-long 2 4s (back legs/uprights) One 3-foot-long 1 3 (horizontal support for pickets) Two 4-inch-long 1 6s (top caps) Paint Window-box liner, not more than 10 34 inches Jigsaw or circular saw Pencil Straightedge ruler Measuring tape Hammer Drill Paintbrush

MATEriAlS

TOOlS

DirECTiONS

1 . Cut the top of the center picket to a point . Cut the tops of the other pickets on a slant the same as the angle of the center point .

This old-fashioned planter is perfect for showcasing your favorite plants.

24 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 25

projects to get the job done

C r e at e a s u n F l o W e r s e e d C at C h e r
keep seeds under control for A heAlthy lAwn

make a FloWer Press

speed up the process of drying fresh flowers And spend more time on your crAfts

unflowers contain a chemical that inhibits the growth of other plants, so it makes sense to keep the seeds off your grass . Youll save hours of raking if you catch sunflower seeds and hulls before they hit the groundplus youll stop them from stunting or killing the grass below your bird feeder .
MATEriAlS

ressed flowers are a delightful ingredient in many crafts, from decorated notepaper and candles to framed collages . You may have already found a pretty flower or leaf on a hike, brought it home, and tucked it into a book to keep it . This is the simplest way to press plant materials, and it often works just fine for a few small plants . However, the average book page is not absorbent enough to do the best possible job of drying a pressed flower, and plant materials can stain pages . The faster you can dry your flowers, the brighter their colors will be . Applying more pressure helps squeeze out moisture . For better results than book drying, try this screw-down flower press .
MATEriAlS

1

One screw eye Two S hooks Wire Dome-shaped squirrel baffle Wire cutter

2-inch plywood Sandpaper Blotting paper or newspaper Four bolts, each at least 3 inches long Four wing nuts to fit the bolts Paper towels Corrugated cardboard Saw Drill Scissors Screwdriver

TOOlS

TOOlS

1 . Attach a screw eye to the bottom of a bird feeder . 2 . Use S hooks and a short piece of wire to attach the upside-down squirrel baffle to the feeder .

DirECTiONS

As your wild birds eat, the seeds and hulls will fall into the dome. Then, when the feeder is empty, birds, squirrels, and chipmunks can hop down into the dome and eat whats been spilled.

1 . Cut a piece of 12-inch plywood to any convenient size . A 12-inch square would be large enough for most garden flowers . For ferns, cut a larger, rectangular piecesay, 12 16 inches . 2 . Cut a second piece of 12-inch plywood to the same dimensions . These will be the covers of your flower press .

DirECTiONS

2 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 27

holes at least 1" from edge Four wing nuts to fit bolts
1

square, for example, cut the paper to about 1134 inches square .) Clip the corners of all sheets at an angle, to clear the bolts that will be inserted later . 6 . When you have gathered your plant materials and are ready to press, insert a bolt in each corner of the bottom cover, beginning from the bottom . Place the bottom cover, with bolts sticking upward, on your work surface . 7 . Place a layer of newspaper several sheets thick or a sheet of blotting paper on the bottom cover . Carefully arrange several pieces of plant material on the paper . For fastest drying, put a layer of paper towels above and below your plant material . Cover with another layer of newspaper or blotting paper . 8 . Build up alternating layers of plant material and absorbent paper . To increase air circulation through the stack and hasten drying, insert a piece of corrugated cardboard about every third layer . End with a layer of absorbent paper . 9 . Top the stack with the second piece of plywood, fitting the bolts into the corner holes .

2" plywood (about 12 12")

Blotting paper with corners cut off Plant material Corrugated cardboard Plant material Blotting paper with corners cut off

2" plywood (about 12 12")

1

Four 3"-long bolts

A homemade plant press is much better for pressing flowers than an old telephone book. A sheet of corrugated cardboard every few layers improves air circulation and speeds up drying.

10 . Screw the wing nuts partway down on opposite corners, and then partly tighten the other two corners . Continue to tighten these wing nuts until they are as tight as you can make them . 11 . Keep the flower press in a warm, dry place with good air circulationfor example, near a heat register or a radiator . 12 . Flowers will dry in about 2 to 3 weeks . Keep them well covered in a dry place until ready to use .

3 . Smooth the rough edges of the plywood lightly with sandpaper . 4 . Drill a hole, at least 1 inch from the edge, in each corner of both plywood covers . 5 . Cut several sheets of blotting paper or newspaper to just shy of the dimensions of your covers . (For covers 12 inches

28 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 2

design a sCareCroW

Perfectly Pressed Flowers

dry flowers and plants quickly to maintain the best color, and follow these tips. Pick plant material on a bright, sunny day after the dew has dried. newly opened flowers will have better quality when dried. Press as soon as possible after picking. arrange plant materials so theyre flat and not touching each other. spread the leaves so theyre not wrinkled. keep the plant material in each drying layer approximately the same thickness to ensure good contact between the absorbent paper and all parts of the plant. otherwise, thinner parts may wrinkle and discolor in drying. remove the petals of large flowers such as hydrangeas and peonies, and press them individually. When drying a layer of bulky flowers, equalize the amount of pressure on them by making collars of blotting paper. Place the collars around each flower before pressing. For fastest drying and best preservation, change the sections of absorbent paper every day for the first 3 days. then, change every other day for about 2 weeks. When you change papers, lift off the drying flowers carefully, without disturbing their positions. dry and reuse blotting paper and paper towels. replace newspaper with a fresh edition; it tends to crinkle slightly when dampened and dried.

scAre AwAy gArden pests with this personAlized whimsicAl creAtion

eople have been making scarecrows for hundreds of years, and for much of that time, they have depended on these figures to discourage crows and other garden predators . Scarecrows are still made for this reason, and they work as well as they ever have . But many are also created as a spring ritual, for the fun of concocting a unique character out of odds and ends, and occasionally, perhaps, even for some silent companionship in the garden .
MATEriAlS

Two sturdy sticks of unequal length (spare 2 4s, old broom handles, retired fence posts, pieces of lath, etc .) Old clothing Nails or wire Utility knife Hammer or wire cutter Staple gun with staples

TOOlS

DirECTiONS

1 . Cut the bottom of the longer stick to a point, and ram it into the

Concoct a scarecrow from odds and ends of clothing and a pair of crossed sticks. Dont try too hard; the fun is seeing just who emerges.

0 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 1

ground . The longer stick is the upright that forms the scarecrows body, and the shorter stick is for the crossbar that forms the arms . 2 . Insert the shorter crossbar into the sleeves of that old flannel shirtor whatever youre using to cover the topbefore you attach the crosspiece to the upright . Then, nail or wire the crossbar securely to the longer upright in at least two places . 3 . Finish dressing the sticks with whatever type of clothing you wish, tying or stapling fabric to the frame as necessary . Your scarecrow can be as dignified, rustic, or offbeat as your attic discards permit . 4 . Many scarecrows are faceless and no less effective for it . But, if you want to make a stab at realism, attach a saucepan, a shingle, a Halloween mask, a plastic jug, or any other facsimile of a head to the top of the basic crossed sticks . Hair may be an old mop, some rope, a rug scrap, or what-have-you .

C o n s t r u C t yo u r o W n P l a n t i n g F l at s
give your seeds A greAt stArt with indoor tlc

lanting flats are like compostyou seldom have more than you need! Though many gardeners nowadays start their seeds in individual pots, old-fashioned wood flats still come in handy: Theyre sturdy and durable and cost little to make, except for the investment of a Saturday morning . Flats are not only for starting seedsthey also make convenient, portable holders for individual pots . And you can custom-fit them to make the best use of your windowsill or lighted plant stand .
MATEriAlS

Slats of varying width Four-penny box nails 1- or 12-inch-thick boards The number of boards and slats youll need depends upon how large you want your flat.
Tape

TOOlS

Sizing Your Flats

the size of your shelf or planting bench and the materials you have available determine the dimensions of your flat. in general, a flat should measure no more than about 14 18 inches, or it will be too heavy to handle easily when filled with wet soil. rectangular flats are traditional, but theres no law against making a square flat if thats what you want. measure the space you have available before you begin construction. For instance, six 12 16 flats will fit neatly on the shelf of a 26 48 fluorescent-lighted plant stand.

Scaring the Crows

if you really want to spook the crows, tie onto your scarecrow dangling aluminum pie pans, foil strips, and other eye-catching or noisy appendages that will flutter and clang in the breeze.

measure Saw or utility knife Clamp Hammer Square

1 . Keeping in mind the space you have available, measure and cut the boards for the sides of the flat . The sides must be deep enough to hold 2 to 3 inches of soil . 2 . Add handles or drill handholds, if you want them, in the two short sides of the flat .

DirECTiONS

2 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 

Boards that are 1 inch thick make a sturdy flat. Boards that are 1 2 inch thick make a lighter flat but are more difficult to nail without splitting the wood. 3 . Calculate how many bottom slats you will need, allowing for 116 to 18 inch of space between the boards for drainage . Cut the bottom slats to length so they are flush with the sides of the box when nailed on . 4 . Use a clamp to stabilize the boards while you are nailing them, or prop the boards or ask a helper to hold them for you . Remember to line them up squarely before nailing . 5 . Using four-penny box nails, nail one of the long sides to each of the two shorter sides . Drive three nails at each corner . 6 . Nail the other long side to the unattached ends of the two short sides, to form a four-sided frame . 7 . Put the open frame on a flat surface . It is still loose jointed at this point . Check the corners with a square to make sure the frame is straight . 8 . Nail on the first bottom flat . This will stabilize the frame and keep the corners from shifting . 9 . Nail on the rest of the bottom slats, leaving about 18 inch between the slats to allow for drainage .

Form a Frugal Potting BenCh

mAke A quick And eAsy potting bench with An old door And 4 4 legs

his bench is a great example of how easily trashan old doorcan be transformed into treasurea brand new potting bench!
MATEriAlS

One 2 10, cut to length of door Old wooden door, hardware removed Four 4 4s, cut in 3-foot lengths Nails Hammer

TOOlS

DirECTiONS

1 . Nail the 2 10 to one edge of the door for a backsplash .

2 . Lay the door flat and mark the corners for attaching the legs . 3 . Attach each leg by nailing through the door . 4 . Stand upright on a level surface . An old door is the basis of this fast and easy potting bench. An attached backsplash helps keep soil where it belongs.

Handles Are a Help

youll find simple handles helpful when you must lug around a lot of large flats. Before constructing the flat, nail a cleat to two opposite sides of the flat for handholds. the size and shape of the cleat arent critical. a scrap of wood an inch or so wide and 3 inches long is satisfactory. nail the cleat from the outside. if the nail protrudes inside, hammer it down flat.

BACK TO CONTENTS 5

Put uP a yule log For the Birds

mAke it A hAppy holidAy for your feAthered friends
his simple bird feeder can be a family project, with children choosing the log and helping with the gluing, filling, and hanging and adults doing the drilling . You might want to make some for gifts, especially for housebound loved ones who would enjoy watching the birds from a window . If your loved one cannot get outside to care for the Yule log, bring it inside for refills and work together to mix the materials and fill the feeder .
MATEriAlS

4 . Insert a sturdy screw eye or hook into the top end of the log, and thread a length of twine or plastic-coated wire through the eye to make a hanger . 5 . Fill each large hole with a mixture of suet and smaller seeds or peanut butter and cornmeal . (Dont use peanut butter alone; it tends to gum up the birds beaks . Use as much cornmeal as you can without making the mixture crumbly .) 6 . Suspend the feeder from a branch (loop the twine or plastic-coated wire around the branch) or roof edge overhang (insert a hook into the overhang and hang the feeder from the hook) .

One log, about 18 inches long and 2 2 inches in diameter Choose a sound log, not rotten, with bark still on to provide a better foothold for the birds. One 24-inch-long, 14-inch-diameter dowel rod Waterproof glue Screw eye or hook Twine or plastic-coated wire Suet and small seeds or peanut butter and cornmeal
1

TOOlS

Saw Drill

1 . Make a straight saw cut across the top end of the log so that you can more easily attach a hanger to it . 2 . Cut the dowel rod into six pieces, each 3 to 4 inches long . Drill 14-inch holes for these dowel perches at intervals no more than 3 or 4 inches apart along the length of the log . The depth of each hole should be about 38 to 12 inch . 3 . Drill circular holes 2 inches in diameter and about 12 inch deep above each small perch hole . Glue the dowel perches in their holes with waterproof glue for outdoor use .
 WEEKEND GARDEN PROJECTS

DirECTiONS

High-fat foods provide plenty of fuel during cold weather, and the cold will preserve the mixture for several months. If the birds havent finished off the mixture by the time warmer weather arrives, replace the food with a fresh mixture.

BACK TO CONTENTS 7

stone elegance
B u i l d a r o C k- Wa l l herB garden

Collect small rocks for use as shims between uneven large rocks . Save some flat rocks to top off the wall . Herb plants with roots See Herbs for Rock Walls on page 42 for some good choices .

TOOlS

Shovel Slim trowel or knife

enjoy fresh herbs todAy, And your greAt-grAndchildren will still enjoy your wAll in the future

DirECTiONS

all gardens are ideal for a small place because you can add planting space within a limited area . In a shady yard, a wall planting will sometimes raise the plants into a patch of sunlight where they will thrive as they could not in deeper shade . The plants prosper in this setting because it provides superb drainage, reflected sunlight, rock-held warmth, excellent air circulation, and a cool, root-sheltering soil . An advantage of growing culinary herbs in a rock wall is that their leaves stay clean . An unmortared rock wall can stand for a century if it is well constructed . A sound wall is held together by the weight of the stones and by the interlocking pattern in which they are placed . Because a dry wall is loose jointed enough to shift gently when frost heaves the soil, no concrete foundation is needed . Nor is it necessary to dig below the frost line to start the wallthere are no mortared seams to crack .
MATEriAlS

1 . Dig a trench as wide as your bottom rocks . Make the trench deep enough to set the bottom layer of rocks about 6 inches below soil level in relatively mild climates or up to 12 inches below soil level where winter freezes are severe . Some experts advise putting several inches of tamped rubble or crushed rock in the bottom of the trench to ensure good drainage .

Before You Begin . . .

Before you begin building your wall, think about drainage of excess water that might freeze and expand in winter, pushing the wall outward. you can bury one or two drain tiles behind the wallat the base and about halfway to the topto carry off water. or, leave weep holesnarrow channels extending through the wall to the outside surfaceto direct water runoff. When backfilling, pack the soil just behind the top course of rock to form a small depression, or swale, to direct runoff away from the face of the wall. Placement of the rocks is important. tilt the stones so that the inner edges are lower than the exposed edges. the slight slant provides good channels for moisture to reach the plant roots and produces a wall better able to resist the outward pressure of the earth behind it. the wall should recede inward, toward the bank, as it rises. in a wet climate, the wall should slant a good foot for every 5 feet of wall height. Where rain is less frequent, 8 to 10 inches will do.

1 ton of undressed stone for 25 to 40 square feet of wall with an average thickness of 1 foot  Rocks that are naturally flat make the most stable construction, but you will need a good selection to fit into a variety of spaces . All the rocks should be of the same kind; dont mix granite and shale, for example, in one wall . Have plenty of square-ended rocks to use for the ends of the wall .

8 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 

2 . In the trench, use your largest stones and those that have one flat side and one irregular side . Dig out the subsoil to make room for the rocks irregularities and place the rocks with their flat sides up . 3 . As you build up the rock courses, place the stones flatthe way youd find them on the groundnot upright or at odd angles . 4 . Place your plants as you build the wall . Fit the plants in the spaces between the rocks . Its important for the stability of the wall to have the stones supported by other stones rather than by a soft bed of soil and plant roots . 5 . To make a good bond, always top a joint between rocks with an overlapping rock to tie the two together . The joint need not always fall in the exact center of the stone above it; a random effect is more pleasing . Just remember the old formula: One over two, two over one . 6 . Place long, large tie stones about every third course, setting them back into the bank for structural support . Use one tie stone for every 10 square feet of completed wall . 7 . Top the wall with large, flat rocks .

SETTiNG iN THE PlaNTS

To give them a secure foothold, add your plants as you build the wall . To balance the planting, you can add others after the wall is completed . Heres how to do it .

As youre building the wall:

1 . Spread a 12-inch layer of soil on two rocks . 2 . Position your plant with its crown at the edge of the wall face and spread its roots out on the soil . 3 . Sift more soil over the roots and tamp it firmly around the plant . 4 . Anchor the plant with the next course of rock .

During wall construction, settle plants in spaces between rocks, cover plant roots with soil, and then continue to add the next course of rocks, which helps anchor the plants below them. Slant the rocks as you lay them to channel moisture toward the plant roots. For structural stability, make sure the face of the wall recedes as it rises.

Refine the planting by adding more plants after the wall is built.Wedge each plant into a cranny between rocks and funnel in soil, packing as firmly as possible.

40 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 41

After the wall is finished:

1 . Use a slim trowel or knife to slide plants into rocky crevices . Or, try a piece of cardboard as a funnel . Insert the cardboard into the rock cranny, slide the plant into place, and funnel soil in around the roots . 2 . Dont be too timid in handling the plantsreally squeeze them in there . The roots need soil around them . Pack sphagnum moss around the planting to help hold the soil .

a d d a W at e r F e at u r e W i t h o u t t h e W at e r
A streAm of stones Adds beAuty to your lAndscApe

f you dont have a natural source of water on your property, you can still enjoy the relaxing touch of a stream meandering through your landscape . Thick black rubber pool liner (30 to 45 millimeters thick) Large pots or half-barrels lined with a plastic tub or rubber pool liner Water plants Large and small rounded stones Chalk or flour

MATEriAlS

Herbs for Rock Walls

Plants with a neat or graceful growth habitcompact, prostrate, trailing, or softly moundedare the best candidates for rock-wall planting. santolina, artemisia, and lavender add silvery and graygreen accents. artemisia silver mount (8 inches tall, with compact and soft foliage) would be a better choice for a rock wall than the 18-inch-tall, rampant-growing artemisia silver king (Artemisia ludoviciana var. albula). stiff, shrubby herbs or those that tend to get leggy (like lemon verbena) fare better in a more conventional planting bed. a rock-wall herb garden is the perfect place to show off dwarf and creeping herbs. any of the dozens of thymes would be perfectly at home. For flowering plants, sweet alyssum (Lobularia maritima), candytufts (Iberis spp.), coralbells (Heuchera sanguinea), catnip (Nepeta cataria), and dwarf lavenders are excellent choices. the plants you introduce into your rock wall should be fairly small but well rooted. a fresh cutting with new, skimpy roots wont survive, nor will a bushy, mature specimen whose roots will be crowded andinitiallyunable to support its mass of foliage. roots will eventually find their way, but they need time to develop.

TOOlS

Shovel or garden fork Utility knife

DirECTiONS

1 . Remove any brush or vegetation from the future streambed area, and turn the soil to make sure all traces of grass and weeds are buried . (Do your digging in summer when your low spot is driest .) 2 . Cover the area with the black rubber pool liner, which will keep weeds from sprouting in your streambed . Dont skip this important step, and dont use thin sheets of plastic for a linertheyll disintegrate and turn into bits and pieces that will be impossible to remove . The rubber pool liner, on the other hand, can last for 20 years . 3 . Once youve lined the area, decide where youd like plants to grow in and around the streambed . The amount of light your streambed gets determines which water plants will grow there . Water lilies need full sun, but cattails and irises will grow in full sun or partial shade .

42 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 4

Half-barrels or large pots make good homes for many different kinds of water plants . Arrange the half-barrels or pots within the boundaries of the stream and along its edges . Then, draw a circle on the liner with chalk or flour to mark the location of each container . Cut holes in the liner for the containers, and sink the half-barrels or pots to at least two-thirds of their height into the ground . 4 . Completely cover the liner with a mix of large and small rounded stones to give your streambed a natural appearance . Rounded stones, or cobbles, are formed in the bottom of streams and rivers, and their shape alone suggests flowing water . You can buy cobbles from building and landscaping supply stores . 5 . Fill the half-barrels in the streambed with water and waterloving plants . If your streambed stays moist, plant the edges

with bog plants, moisture-loving grasses like Japanese silver grass (Miscanthus sinensis), or water-dwelling plants like yellow flat (Iris pseudacorus) . In areas that dont carry runoff water, plant the stream edges with Siberian irises and grasses like blue Lyme grass (Elymus arenarius Glaucus) that dont mind drier conditions . Or continue the illusion of a really wet area by setting halfbarrels of water plants along the edges of the stream, too . Give your stream the look of a real watercourse by planting the edges with tall grasses, irises, rushes, sedges, and shrubs. Set tubs of potted water lilies inside the stream for a finishing touch.

Water lily

Before You Begin . . .

to decide where to place your streambed, think of your dry creek bed as a real stream, and imagine where water would flow through your yard. look for the lowest parts of your lawn and for areas where rainwater runs off. those are the places to locate your streambed since it will look most natural. make your stream the shape of an actual flow of water. imagine that heavy rains sent water flowing through your yard, and try to imitate the shape of the runoff. if you have a deep gully in your yard, the stream will run through it and be narrow. if you live on flatter land, your streambed will run through the lowest spot and be wider. then, when you do have torrential rains, youll find that the dry streambed carries off water just as well as a real waterway. keep that in mind when you place the lowest end of your streambed. make sure it ends in a site that can handle extra water, not next to an area like your patio where runoff would be a nuisance.

yellow flag japanese silver grass

44 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS 45

C r e at e a s m a l l P o n d
with A pond you wont get just wAter youll get new wildlife

water feature can bring more beauty to your garden than you may imagine . You know youll have a nice display of water plants, but you might be surprised by the birds, dragonflies, frogs, and water striders your pond is sure to attract .
MATEriAlS

Black rubber 32-millimeter-thick pool liner To get the right dimensions for the liner, multiply the depth of your pond by 3, and then add that number to the total width and length of the pool to get the right size. For example, if your pool is 3 feet deep and 4 feet in diameter, with an extra 18 inches on either end for the rim, then add 9 feet to the total width (4' + 18" + 18" = 7 ' ) and length (7 ' ) for a total of 23 (9 ' + 7 ' + 7 ' = 23 ' ).Youll need a liner thats 23 feet 23 feet. Fine sand Stones, including several flat rocks Piece of an old garden hose Recirculating submersible water pump Shovel Utility knife

3 . Smooth the sides of the hole and remove any sharp stones or roots from the bottom so they dont puncture the rubber pool liner . Put a layer of fine sand in the bottom to prevent punctures . With the help of a friend, flatten the liner so it fits the shape of the hole . Then, smooth it into place, starting at the center and working your way to the edges . To do this, take off your shoes and get into the hole barefoot . Fold the excess liner back onto the shallow rim as you work your way around the diameter so it fits neatly . Trim any excess liner with a utility knife . When you reach the curve of the slope, be sure to bring the liner up as far as it will reach rather than folding it over . 4 . Hire an electricianunless youre experienced with working with electricity and waterto make a small shallow trench from the edge of the ponds rim to your house and install conduit and electric wires . 5 . Place stones all along the shallow pond rim to cover the liner, except at the back where the slope is . Next, take a piece of old garden hose and lay it against the back of the hole from the bottom of the pond up the slope . Run the hose as high as you want your waterfall to beusually about 3 feet above the water surfacebut not higher than the liner . 6 . Finish covering the back part of the pond rim with rocks, and place rocks along the curve in the slope so the hose is hidden . Make sure the hose protrudes a bit from the rocks at the top and that water from the hose wont run back under the liner . Attach the hose in the bottom of the hole to a recirculating submersible water pump . Connect submersible wiring from the pump up to the conduit and then through the conduit to electrical service at your house . 7 . Add water to your pond hole until it reaches an inch from the top, then turn on the pump . Arrange the rocks at the top of the waterfall so you cant see the end of the hose and so the water flows down naturally over the rocks . Use several flat rocks for the waterfallthe water will look attractive running down the rocks, and it will make a pleasant sound .
BACK TO CONTENTS 47

TOOlS

1 . Site the pond at the base of a slope if you can so theres some high ground where you can build a waterfall . If you dont have a slope, build one out of rocks and surround the back side with shrubs and trees for camouflage . 2 . Excavate a hole at least 3 feet deep and 4 feet in diameter . Next, dig out an 18-inch-wide and 8-inch-deep lip all the way around the hole so you have a rim for rocks to sit on . At the back of the hole, shape the slope into a curve where your waterfall will go .

DirECTiONS

4 WEEKEND GARDEN PROJECTS

8 . Allow the water sit for a week before you add plants or fishit needs time to warm up and let any chlorine escape . Youll need goldfish or mosquito fish to devour any mosquito larvae that hatch in the water . And youll want a variety of plants, too, because theyre fun to grow and they keep the water clean .

18 8

4 32-millimeterthick rubber pool liner

[1]

[2] You can build a small pond in a weekend with a little help from your friends. First, choose a site against a slope and dig out the hole and a ledge [1]. Next, add a liner [2]. Install a pump and a piece of hose to direct the water [3].Then, place the rocks and fill the hole with water. Adjust the rocks for good water flow and so the hose cant be seen. Add plants and fish to your pond, and watch birds and other beneficials flock to your new water feature [4-].
hose submersible electrical wires

submersible pump

Conduit

[3]

[4]
48 WEEKEND GARDEN PROJECTS

BACK TO CONTENTS

Welcome to Organic Gardening!

Your satisfaction is important to us. Our customer service staff takes pride in making sure that you are completely satisfied with your subscription. To contact us, please see the information below.

SUBSCRIBER SERVICE INFORMATION

Online Subscriber Service www.OrganicGardening.com
Available 24 hours a day, 7 days a week Check your account status (expiration date and latest payment) Change your address Pay your bill Report a missing or damaged issue Report other problems by sending an e-mail message

Postal Mail
Organic Gardening Magazine PO Box 7320 Red Oak, IA 51591-0320

Fax
(712) 623-5545

Phone
(800) 666-2206 or (610) 967-8525

E-Mail
[email protected]

200999501 OG Printed in USA

00XI
k Printed on Recyclable Paper