Manual Obd

Table of Contents
INTRODUCTION WHAT IS OBD? ........................................................................ YOU CAN DO IT! .............................................................................. SAFETY PRECAUTIONS SAFETY FIRST! ........................................................................ ABOUT THE DIAGNOSTIC TOOL VEHICLES COVERED ............................................................. BATTERY REPLACEMENT ..................................................... DIAGNOSTIC TOOL CONTROLS CONTROLS AND INDICATORS ............................................. DISPLAY FUNCTIONS ............................................................ ONBOARD DIAGNOSTICS COMPUTER ENGINE CONTROLS ......................................... DIAGNOSTIC TROUBLE CODES (DTCs) .............................. OBD2 MONITORS .................................................................... PREPARATION FOR TESTING PRELIMINARY VEHICLE DIAGNOSTIC WORKSHEET ......... BEFORE YOU BEGIN .............................................................. VEHICLE SERVICE MANUALS ............................................... USING THE DIAGNOSTIC TOOL CODE RETRIEVAL PROCEDURE .......................................... VIEWING ENHANCED DTCs ................................................... ERASING DIAGNOSTIC TROUBLE CODES (DTCs) .............. I/M READINESS TESTING ...................................................... ADDITIONAL FUNCTIONS VIEWING VEHICLE INFORMATION ....................................... ADJUSTMENTS/SETTINGS AND DTC LIBRARY ................... GENERIC (GLOBAL) OBD2 PID LIST ............................................ GLOSSARY INTRODUCTION ...................................................................... GLOSSARY OF TERMS AND ABBREVIATIONS ................... WARRANTY AND SERVICING LIMITED ONE YEAR WARRANTY .......................................... SERVICE PROCEDURES .......................................................
1 2 3 5 6 7 9 11 16 19 28 31 32 33 39 47 49 55 57 62 67 67 69 69
OBD2
Introduction
WHAT IS OBD?
WHAT IS OBD?
The Enhanced CanOBD2 Diagnostic Tool is designed to work on all OBD2 compliant vehicles. All 1996 and newer vehicles (cars, light trucks and SUVs) sold in the United States are OBD2 compliant. One of the most exciting improvements in the automobile industry was the addition of onboard diagnostics (OBD) on vehicles, or in more basic terms, the computer that activates the vehicles CHECK ENGINE light. OBD1 was designed to monitor manufacturer-specific systems on vehicles built from 1981 to 1995. Then came the development of OBD2, which is on all 1996 and newer vehicles sold in the U.S. Like its predecessor, OBD2 was adopted as part of a government mandate to lower vehicle emissions. But what makes OBD2 unique is its universal application for all late model cars and trucks - domestic and import. This sophisticated program in the vehicles main computer system is designed to detect failures in a range of systems, and can be accessed through a universal OBD2 port, which is usually found under the dashboard. For all OBD systems, if a problem is found, the computer turns on the CHECK ENGINE light to warn the driver, and sets a Diagnostic Trouble Code (DTC) to identify where the problem occurred. A special diagnostic tool, such as the Enhanced CanOBD2 Diagnostic Tool, is required to retrieve these codes, which consumers and professionals use as a starting point for repairs. The Enhanced CanOBD2 Diagnostic Tool provides the additional ability to retrieve enhanced DTCs from most Chrysler/Jeep, Ford/Mazda, GM/Isuzu, Honda/Acura and Toyota/Lexus vehicles. The types of enhanced data available depends on the vehicle make.
To learn more about vehicle Computer Control Systems and OBD2, see COMPUTER ENGINE CONTROLS on page 15.
OBD2
You Can Do It!

EASY TO USE - EASY TO VIEW - EASY TO DEFINE
Easy To Use . . . .
Connect the Diagnostic Tool to the vehicles test connector. Turn the ignition key "On. The Diagnostic Tool automatically links to the vehicles computer.
Easy To View . . . .
The Diagnostic Tool retrieves stored codes, Freeze Frame data and system status. Codes, system status and Freeze Frame data are displayed on the Diagnostic Tools LCD display screen. System status is indicated by LED indicators.
Easy To Define . . . .
Read code definitions from the Diagnostic Tools LCD display. View Freeze Frame data.
OBD2
Safety Precautions
SAFETY FIRST!
SAFETY FIRST!
To avoid personal injury, instrument damage and/or damage to your vehicle; do not use the OBD2 Code Reader before reading this manual. This manual describes common test procedures used by experienced service technicians. Many test procedures require precautions to avoid accidents that can result in personal injury, and/or damage to your vehicle or test equipment. Always read your vehicle's service manual and follow its safety precautions before and during any test or service procedure. ALWAYS observe the following general safety precautions: When an engine is running, it produces carbon monoxide, a toxic and poisonous gas. To prevent serious injury or death from carbon monoxide poisoning, operate the vehicle ONLY in a well-ventilated area. To protect your eyes from propelled objects as well as hot or caustic liquids, always wear approved safety eye protection. When an engine is running, many parts (such as the coolant fan, pulleys, fan belt etc.) turn at high speed. To avoid serious injury, always be aware of moving parts. Keep a safe distance from these parts as well as other potentially moving objects. Engine parts become very hot when the engine is running. To prevent severe burns, avoid contact with hot engine parts. Before starting an engine for testing or troubleshooting, make sure the parking brake is engaged. Put the transmission in park (for automatic transmission) or neutral (for manual transmission). Block the drive wheels with suitable blocks. Connecting or disconnecting test equipment when the ignition is ON can damage test equipment and the vehicle's electronic components. Turn the ignition OFF before connecting the Diagnostic Tool to or disconnecting the Diagnostic Tool from the vehicles Data Link Connector (DLC).
P RND L
OBD2
Safety Precautions
SAFETY FIRST!
To prevent damage to the on-board computer when taking vehicle electrical measurements, always use a digital multimeter with at least 10 MegOhms of impedance. Fuel and battery vapors are highly flammable. To prevent an explosion, keep all sparks, heated items and open flames away from the battery and fuel / fuel vapors. DO NOT SMOKE NEAR THE VEHICLE DURING TESTING. Don't wear loose clothing or jewelry when working on an engine. Loose clothing can become caught in the fan, pulleys, belts, etc. Jewelry is highly conductive, and can cause a severe burn if it makes contact between a power source and ground.
OBD2
About the Diagnostic Tool

VEHICLES COVERED
VEHICLES COVERED
The Enhanced CanOBD2 Diagnostic Tool is designed to work on all OBD2 compliant vehicles. All 1996 and newer vehicles (cars and light trucks) sold in the United States are OBD2 compliant. Federal law requires that all 1996 and newer cars and light trucks sold in the United States must be OBD2 compliant; this includes all Domestic, Asian and European vehicles. Some 1994 and 1995 vehicles are OBD2 compliant. To find out if a 1994 or 1995 vehicle is OBD2 compliant, check the following: 1. The Vehicle Emissions Control Information (VECI) Label. This label is located under the hood or by the radiator of most vehicles. If the vehicle is OBD2 compliant, the label will state OBD II Certified.
VEHICLE EMISSION CONTROL INFORMATION
ENGINE FAMILY DISPLACEMENT EFN2.6YBT2BA 2.6L OBD II CERTIFIED
VEHICLE
MANUFACTURER
THIS VEHICLE CONFORMS TO U.S. EPA AND STATE OF CALIFORNIA REGULATIONS APPLICABLE TO 1999 MODEL YEAR NEW TLEV PASSENGER CARS.
REFER TO SERVICE MANUAL FOR ADDITIONAL INFORMATION TUNE-UP CONDITIONS: NORMAL OPERATING ENGINE TEMPERATURE, ACCESSORIES OFF, COOLING FAN OFF, TRANSMISSION IN NEUTRAL EXHAUST EMISSIONS STANDARDS CERTIFICATION IN-USE
SPARK PLUG TYPE NGK BPRE-11 GAP: 1.1MM
OBD II CERTIFIED
STANDARD CATEGORY TLEV TLEV INTERMEDIATE
CATALYST
2. Government Regulations require that all OBD2 compliant vehicles must have a common sixteen-pin Data Link Connector (DLC).
1 2 3 4 5 6 7 8 9 10111213141516
Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD2 compliant. Only those vehicles with a Vehicle Emissions Control Label stating OBD II Certified are OBD2 compliant.
Data Link Connector (DLC) Location

The 16-pin DLC is usually located under the instrument panel (dash), within 12 inches (300 mm) of center of the panel, on the drivers side of most vehicles. It should be easily accessible and visible from a kneeling position outside the vehicle with the door open.
LEFT CORNER OF DASH
NEAR CENTER OF DASH
BEHIND ASHTRAY
OBD2
About the Diagnostic Tool

BATTERY REPLACEMENT
On some Asian and European vehicles the DLC is located behind the ashtray (the ashtray must be removed to access it) or on the far left corner of the dash. If the DLC cannot be located, consult the vehicles service manual for the location.
BATTERY REPLACEMENT
Replace batteries when the battery symbol is visible on display and/or the 3 LEDS are all lit and no other data is visible on screen. 1. Locate the battery cover on the back of the Diagnostic Tool. 2. Slide the battery cover off (use your fingers). 3. Replace batteries with two AA-size batteries (for longer life, use Alkaline-type batteries). 4. Reinstall the battery cover on the back of the Diagnostic Tool.
Adjustments After Battery Installation

The first time the unit is turned on, you must select the desired display language (English, French or Spanish) and unit of measurement (USA or Metric) as follows: 1. Press the POWER/LINK button to turn the Diagnostic Tool ON. The Select displays. Language screen
2. Use the UP and DOWN buttons, as necessary, to highlight the desired display language. 3. When the desired display language is button to selected, press the ENTER confirm your selection. The Select Unit screen displays. and DOWN buttons, as necessary, to highlight 4. Use the UP the desired unit of measurement. 5. When the desired unit of measurement is selected, press the FF/M button to confirm your selection. After the initial language and unit of measurement selections are performed, these, as well as other settings, can be changed as desired. Proceed to ADJUSTMENTS/SETTINGS AND DTC LIBRARY on page 57 for further instructions.
OBD2
Diagnostic Tool Controls

CONTROLS AND INDICATORS
12
8 6 1 2 3 7
11 9 10 4 5
Figure 1. Controls and Indicators See Figure 1 for the locations of items 1 through 12, below. 1. ERASE button - Erases Diagnostic Trouble Codes (DTCs), and Freeze Frame data from your vehicles computer, and resets Monitor status. ENTER button - When in Menu mode, confirms the selected option or value. DTC button - Displays the DTC View screen and/or scrolls the LCD display to view DTCs. POWER/LINK button - When the Diagnostic Tool IS NOT connected to a vehicle, turns the Diagnostic Tool On and Off. When the Diagnostic Tool is connected to a vehicle, links the Diagnostic Tool to the vehicles PCM to retrieve diagnostic data from the computers memory. To turn the Diagnostic Tool "On", you must press and hold the POWER/LINK button for approximately 3 seconds. 5. FF/M button When pressed while linked to a vehicle, displays Freeze Frame Data for the priority code (DTC #1). When pressed and held while linked to a vehicle, displays the Menu.
2. 3. 4.
OBD2

6.
DOWN button - When in MENU mode, scrolls DOWN through the menu and submenu selection options. When retrieving and viewing DTCs, scrolls down through the current display screen to display any additional data. UP button - When in MENU mode, scrolls UP through the menu and submenu selection options. When retrieving and viewing DTCs, scrolls ups through the current display screen to display any additional data.
7.
8. GREEN LED - Indicates that all engine systems are running normally (all Monitors on the vehicle are active and performing their diagnostic testing, and no DTCs are present). 9. YELLOW LED - Indicates there is a possible problem. A Pending DTC is present and/or some of the vehicles emission monitors have not run their diagnostic testing. 10. RED LED - Indicates there is a problem in one or more of the vehicles systems. The red LED is also used to show that DTC(s) are present. DTCs are shown on the Diagnostic Tools LCD display. In this case, the Malfunction Indicator (Check Engine) lamp on the vehicles instrument panel will light steady on. 11. LCD Display - Displays settings Menu and submenus, test results, Diagnostic Tool functions and Monitor status information. See DISPLAY FUNCTIONS, on next page, for more details. 12. CABLE - Connects the Diagnostic Tool to the vehicles Data Link Connector (DLC).
OBD2

DISPLAY FUNCTIONS
DISPLAY FUNCTIONS
Figure 2. Display Functions See Figure 2 for the locations of items 1 through 14, below. 1. I/M MONITOR STATUS field - Identifies the I/M Monitor status area. 2. Monitor icons - Indicate which Monitors are supported by the vehicle under test, and whether or not the associated Monitor has run its diagnostic testing (Monitor status). When a Monitor icon is solid, it indicates that the associated Monitor has completed its diagnostic testing. When a Monitor icon is flashing, it indicates that the vehicle supports the associated Monitor, but the Monitor has not yet run its diagnostic testing. 3. Vehicle icon - Indicates whether or not the Diagnostic Tool is being properly powered through the vehicles Data Link Connector (DLC). A visible icon indicates that the Diagnostic Tool is being powered through the vehicles DLC connector. Link icon - Indicates whether or not the Diagnostic Tool is communicating (linked) with the vehicles on-board computer. When visible, the Diagnostic Tool is communicating with the computer. If the Link icon is not visible, the Diagnostic Tool is not communicating with the computer. Computer icon - When this icon is visible it indicates that the Diagnostic Tool is linked to a personal computer. Optional software is available that makes it possible to upload retrieved data to a personal computer. Diagnostic Tool Internal Battery icon - When visible, indicates the Diagnostic Tool batteries are low and should be replaced. If the batteries are not replaced when the battery symbol is "on", all 3 LEDs will light up as a last resort indicator to warn you that the batteries need replacement. No data will be displayed on screen when all 3 LEDs are lit.
4.
5.
6.
OBD2

DISPLAY FUNCTIONS
7. DTC Display Area - Displays the Diagnostic Trouble Code (DTC) number. Each fault is assigned a code number that is specific to that fault. 8. Test Data Display Area - Displays DTC definitions, Freeze Frame data, and other pertinent test information messages. 9. FREEZE FRAME icon - Indicates that there is Freeze Frame data from Priority Code (Code #1) stored in the vehicles computer memory. 10. PERMANENT icon - Indicates the currently displayed DTC is a Permanent code. 11. PENDING icon - Indicates the currently displayed DTC is a Pending code. 12. MIL icon - Indicates the status of the Malfunction Indicator Lamp (MIL). The MIL icon is visible only when a DTC has commanded the MIL on the vehicles dashboard to light. 13. Code Number Sequence - The Diagnostic Tool assigns a sequence number to each DTC that is present in the computers memory, starting with 01. This number indicates which code is currently displayed. Code number 01 is always the highest priority code, and the one for which Freeze Frame data has been stored. If 01 is a Pending code, there may or may not be Freeze Frame data stored in memory. 14. Code Enumerator - Indicates the total number of codes retrieved from the vehicles computer.
10
OBD2
Onboard Diagnostics
COMPUTER ENGINE CONTROLS

The Introduction of Electronic Engine Controls
Electronic Computer Control Systems make it possible for vehicle manufacturers to comply with the tougher emissions and fuel efficiency standards mandated by State and Federal Governments. As a result of increased air pollution (smog) in large cities, such as Los Angeles, the California Air Resources Board (CARB) and the Environmental Protection Agency (EPA) set new regulations and air pollution standards to deal with the problem. To further complicate matters, the energy crisis of the early 1970s caused a sharp increase in fuel prices over a short period. As a result, vehicle manufacturers were not only required to comply with the new emissions standards, they also had to make their vehicles more fuel-efficient. Most vehicles were required to meet a miles-per-gallon (MPG) standard set by the U.S. Federal Government. Precise fuel delivery and spark timing are needed to reduce vehicle emissions. Mechanical engine controls in use at the time (such as ignition points, mechanical spark advance and the carburetor) responded too slowly to driving conditions to properly control fuel delivery and spark timing. This made it difficult for vehicle manufacturers to meet the new standards. A new Engine Control System had to be designed and integrated with the engine controls to meet the stricter standards. The new system had to: Respond instantly to supply the proper mixture of air and fuel for any driving condition (idle, cruising, low-speed driving, high-speed driving, etc.). Calculate instantly the best time to ignite the air/fuel mixture for maximum engine efficiency. Perform both these tasks without affecting vehicle performance or fuel economy. Vehicle Computer Control Systems can perform millions of calculations each second. This makes them an ideal substitute for the slower mechanical engine controls. By switching from mechanical to electronic engine controls, vehicle manufacturers are able to control fuel delivery and spark timing more precisely. Some newer Computer Control Systems also provide control over other vehicle functions, such as transmission, brakes, charging, body, and suspension systems.
OBD2
11
Onboard Diagnostics
The Basic Engine Computer Control System
The Computer Control System consists of an on-board computer and several related control devices (sensors, switches, and actuators). The on-board computer is the heart of the Computer Control System. The computer contains several programs with preset reference values for air/fuel ratio, spark or ignition timing, injector pulse width, engine speed, etc. Separate values are provided for various driving conditions, such as idle, low speed driving, high-speed driving, low load, or high load. The preset reference values represent the ideal air/fuel mixture, spark timing, transmission gear selection, etc., for any driving condition. These values are programmed by the vehicle manufacturer, and are specific to each vehicle model. Most on-board computers are located inside the vehicle behind the dashboard, under the passengers or drivers seat, or behind the right kick panel. However, some manufacturers may still position it in the engine compartment. Vehicle sensors, switches, and actuators are located throughout the engine, and are connected by electrical wiring to the on-board computer. These devices include oxygen sensors, coolant temperature sensors, throttle position sensors, fuel injectors, etc. Sensors and switches are input devices. They provide signals representing current engine operating conditions to the computer. Actuators are output devices. They perform actions in response to commands received from the computer. The on-board computer receives information inputs from sensors and switches located throughout the engine. These devices monitor critical engine conditions such as coolant temperature, engine speed, engine load, throttle position, air/fuel ratio etc. The computer compares the values received from these sensors with its preset reference values, and makes corrective actions as needed so that the sensor values always match the preset reference values for the current driving condition. The computer makes adjustments by commanding other devices such as the fuel injectors, idle air control, EGR valve or Ignition Module to perform these actions.
OUTPUT DEVICES Fuel Injectors Idle Air Control EGR Valve Ignition Module On-Board Computer INPUT DEVICES Coolant Temperature Sensor Throttle Position Sensor Fuel Injectors
TYPICAL COMPUTER CONTROL SYSTEM
INPUT DEVICES Oxygen Sensors
12
OBD2
Onboard Diagnostics
Vehicle operating conditions are constantly changing. The computer continuously makes adjustments or corrections (especially to the air/fuel mixture and spark timing) to keep all the engine systems operating within the preset reference values.
On-Board Diagnostics - First Generation (OBD1)

With the exception of some 1994 and 1995 vehicles, most vehicles from 1982 to 1995 are equipped with some type of first generation On-Board Diagnostics. Beginning in 1988, Californias Air Resources Board (CARB), and later the Environmental Protection Agency (EPA) required vehicle manufacturers to include a self-diagnostic program in their on-board computers. The program would be capable of identifying emissions-related faults in a system. The first generation of Onboard Diagnostics came to be known as OBD1. OBD1 is a set of self-testing and diagnostic instructions programmed into the vehicles on-board computer. The programs are specifically designed to detect failures in the sensors, actuators, switches and wiring of the various vehicle emissions-related systems. If the computer detects a failure in any of these components or systems, it lights an indicator on the dashboard to alert the driver. The indicator lights only when an emissions-related problem is detected. The computer also assigns a numeric code for each specific problem that it detects, and stores these codes in its memory for later retrieval. These codes can be retrieved from the computers memory with the use of a Code Reader or a Scan Tool.
On-Board Diagnostics - Second Generation (OBD2)

In addition to performing all the functions of the OBD1 System, the The OBD2 System is OBD2 System has been enhanced with an enhancement of the new Diagnostic Programs. These OBD1 System. programs closely monitor the functions of various emissions-related components and systems (as well as other systems) and make this information readily available (with the proper equipment) to the technician for evaluation. The California Air Resources Board (CARB) conducted studies on OBD1 equipped vehicles. The information that was gathered from these studies showed the following: A large number of vehicles had deteriorating or degraded emissions-related components. These components were causing an increase in emissions.
OBD2
13
Onboard Diagnostics
Because OBD1 systems only detect failed components, the degraded components were not setting codes. Some emissions problems related to degraded components only occur when the vehicle is being driven under a load. The emission checks being conducted at the time were not performed under simulated driving conditions. As a result, a significant number of vehicles with degraded components were passing Emissions Tests. Codes, code definitions, diagnostic connectors, communication protocols and emissions terminology were different for each manufacturer. This caused confusion for the technicians working on different make and model vehicles. To address the problems made evident by this study, CARB and the EPA passed new laws and standardization requirements. These laws required that vehicle manufacturers to equip their new vehicles with devices capable of meeting all of the new emissions standards and regulations. It was also decided that an enhanced on-board diagnostic system, capable of addressing all of these problems, was needed. This new system is known as On-Board Diagnostics Generation Two (OBD2). The primary objective of the OBD2 system is to comply with the latest regulations and emissions standards established by CARB and the EPA. The Main Objectives of the OBD2 System are: To detect degraded and/or failed emissions-related components or systems that could cause tailpipe emissions to exceed by 1.5 times the Federal Test Procedure (FTP) standard. To expand emissions-related system monitoring. This includes a set of computer run diagnostics called Monitors. Monitors perform diagnostics and testing to verify that all emissions-related components and/or systems are operating correctly and within the manufacturers specifications. To use a standardized Diagnostic Link Connector (DLC) in all vehicles. (Before OBD2, DLCs were of different shapes and sizes.) To standardize the code numbers, code definitions and language used to describe faults. (Before OBD2, each vehicle manufacturer used their own code numbers, code definitions and language to describe the same faults.) To expand the operation of the Malfunction Indicator Lamp (MIL). To standardize communication procedures and protocols between the diagnostic equipment (Scan Tools, Code Readers, etc.) and the vehicles on-board computer.
OBD2 Terminology
The following terms and their definitions are related to OBD2 systems. Read and reference this list as needed to aid in the understanding of OBD2 systems.
14
OBD2
Onboard Diagnostics
Powertrain Control Module (PCM) - The PCM is the OBD2 accepted term for the vehicles on-board computer. In addition to controlling the engine management and emissions systems, the PCM also participates in controlling the powertrain (transmission) operation. Most PCMs also have the ability to communicate with other computers on the vehicle (ABS, ride control, body, etc.). Monitor - Monitors are diagnostic routines programmed into the PCM. The PCM utilizes these programs to run diagnostic tests, and to monitor operation of the vehicles emissions-related components or systems to ensure they are operating correctly and within the vehicles manufacturer specifications. Currently, up to eleven Monitors are used in OBD2 systems. Additional Monitors will be added as the OBD2 system is further developed. Not all vehicles support all Fifteen Monitors. Enabling Criteria - Each Monitor is designed to test and monitor the operation of a specific part of the vehicles emissions system (EGR system, oxygen sensor, catalytic converter, etc.). A specific set of conditions or driving procedures must be met before the computer can command a Monitor to run tests on its related system. These conditions are known as Enabling Criteria. The requirements and procedures vary for each Monitor. Some Monitors only require the ignition key to be turned On for them to run and complete their diagnostic testing. Others may require a set of complex procedures, such as, starting the vehicle when cold, bringing it to operating temperature, and driving the vehicle under specific conditions before the Monitor can run and complete its diagnostic testing. Monitor Has/Has Not Run - The terms Monitor has run or Monitor has not run are used throughout this manual. Monitor has run, means the PCM has commanded a particular Monitor to perform the required diagnostic testing on a system to ensure the system is operating correctly (within factory specifications). The term Monitor has not run means the PCM has not yet commanded a particular Monitor to perform diagnostic testing on its associated part of the emissions system. Trip - A Trip for a particular Monitor requires that the vehicle is being driven in such a way that all the required Enabling Criteria for the Monitor to run and complete its diagnostic testing are met. The Trip Drive Cycle for a particular Monitor begins when the ignition key is turned On. It is successfully completed when all the Enabling Criteria for the Monitor to run and complete its diagnostic testing are met by the time the ignition key is turned Off. Since each of the eleven monitors is designed to run diagnostics and testing on a different part of the engine or emissions system, the Trip Drive Cycle needed for each individual Monitor to run and complete varies.
OBD2
15
Onboard Diagnostics
DIAGNOSTIC TROUBLE CODES (DTCs)
OBD2 Drive Cycle - An OBD2 Drive Cycle is an extended set of driving procedures that takes into consideration the various types of driving conditions encountered in real life. These conditions may include starting the vehicle when it is cold, driving the vehicle at a steady speed (cruising), accelerating, etc. An OBD2 Drive Cycle begins when the ignition key is turned On (when cold) and ends when the vehicle has been driven in such a way as to have all the Enabling Criteria met for all its applicable Monitors. Only those trips that provide the Enabling Criteria for all Monitors applicable to the vehicle to run and complete their individual diagnostic tests qualify as an OBD2 Drive Cycle. OBD2 Drive Cycle requirements vary from one model of vehicle to another. Vehicle manufacturers set these procedures. Consult your vehicles service manual for OBD2 Drive Cycle procedures. Do not confuse a Trip Drive Cycle with an OBD2 Drive Cycle. A Trip Drive Cycle provides the Enabling Criteria for one specific Monitor to run and complete its diagnostic testing. An OBD2 Drive Cycle must meet the Enabling Criteria for all Monitors on a particular vehicle to run and complete their diagnostic testing. Warm-up Cycle - Vehicle operation after an engine off period where engine temperature rises at least 40F (22C) from its temperature before starting, and reaches at least 160F (70C). The PCM uses warm-up cycles as a counter to automatically erase a specific code and related data from its memory. When no faults related to the original problem are detected within a specified number of warm-up cycles, the code is erased automatically.

Diagnostic Trouble Codes (DTCs) are Diagnostic Trouble meant to guide you to the proper service procedure in the vehicles Codes (DTCs) are service manual. DO NOT replace parts codes that identify a based only on DTCs without first specific problem area. consulting the vehicles service manual for proper testing procedures for that particular system, circuit or component. DTCs are alphanumeric codes that are used to identify a problem that is present in any of the systems that are monitored by the on-board computer (PCM). Each trouble code has an assigned message that identifies the circuit, component or system area where the problem was found. OBD2 diagnostic trouble codes are made up of five characters: The 1st character is a letter. It identifies the main system where the fault occurred (Body, Chassis, Powertrain, or Network). The 2nd character is a numeric digit. It identifies the type of code (Generic or Manufacturer-Specific).
16
OBD2
Onboard Diagnostics
Generic DTCs are codes that are used by all vehicle manufacturers. The standards for generic DTCs, as well as their definitions, are set by the Society of Automotive Engineers (SAE). Manufacturer-Specific DTCs are codes that are controlled by the vehicle manufacturers. The Federal Government does not require vehicle manufacturers to go beyond the standardized generic DTCs in order to comply with the new OBD2 emissions standards. However, manufacturers are free to expand beyond the standardized codes to make their systems easier to diagnose. The 3rd character is a numeric digit. It identifies the specific system or sub-system where the problem is located. The 4th and 5th characters are numeric digits. They identify the section of the system that is malfunctioning.
OBD2 DTC EXAMPLE

P0201 - Injector Circuit Malfunction, Cylinder 1 B C P U 0 1 2 3 Body Chassis Powertrain Network Generic Manufacturer Specific Generic Includes both Generic and Manufacturer Specific Codes
P0201
Identifies the system where the problem is located: 1 - Fuel and Air Metering 2 - Fuel and Air Metering (injector circuit malfunction only) 3 - Ignition System or Misfire 4 - Auxiliary Emission Control System 5 - Vehicle Speed Control and Idle Control System 6 - Computer Output Circuits 7 - Transmission 8 - Transmission Identifies what section of the system is malfunctioning
OBD2
17
Onboard Diagnostics
DTCs and MIL Status

When the vehicles on-board computer detects a failure in an emissions-related component or system, the computers internal diagnostic program assigns a diagnostic trouble code (DTC) that points to the system (and subsystem) where the fault was found. The diagnostic program saves the code in the computers memory. It records a Freeze Frame of conditions present when the fault was found, and lights the Malfunction Indicator Lamp (MIL). Some faults require detection for two trips in a row before the MIL is turned on. The Malfunction Indicator Lamp (MIL) is the accepted term used to describe the lamp on the dashboard that lights to warn the driver that an emissions-related fault has been found. Some manufacturers may still call this lamp a Check Engine or Service Engine Soon light. There are two types of DTCs used for emissions-related faults: Type A and Type B. Type A codes are One-Trip codes; Type B DTCs are usually Two-Trip DTCs. When a Type A DTC is found on the First Trip, the following events take place: The computer commands the MIL On when the failure is first found. If the failure causes a severe misfire that may cause damage to the catalytic converter, the MIL flashes once per second. The MIL continues to flash as long as the condition exists. If the condition that caused the MIL to flash is no longer present, the MIL will light steady On. A DTC is saved in the computers memory for later retrieval. A Freeze Frame of the conditions present in the engine or emissions system when the MIL was ordered On is saved in the computers memory for later retrieval. This information shows fuel system status (closed loop or open loop), engine load, coolant temperature, fuel trim value, MAP vacuum, engine RPM and DTC priority. When a Type B DTC is found on the First Trip, the following events take place: The computer sets a Pending DTC, but the MIL is not ordered On. Freeze Frame data may or may not be saved at this time depending on manufacturer. The Pending DTC is saved in the computers memory for later retrieval. If the failure is found on the second consecutive trip, the MIL is ordered On. Freeze Frame data is saved in the computers memory. If the failure is not found on the second Trip, the Pending DTC is erased from the computers memory. The MIL will stay lit for both Type A and Type B codes until one of the following conditions occurs:
18
OBD2
Onboard Diagnostics
OBD2 MONITORS
If the conditions that caused the MIL to light are no longer present for the next three trips in a row, the computer automatically turns the MIL Off if no other emissions-related faults are present. However, the DTCs remain in the computers memory as a history code for 40 warm-up cycles (80 warm-up cycles for fuel and misfire faults). The DTCs are automatically erased if the fault that caused them to be set is not detected again during that period. Misfire and fuel system faults require three trips with similar conditions before the MIL is turned Off. These are trips where the engine load, RPM and temperature are similar to the conditions present when the fault was first found. After the MIL has been turned off, DTCs and Freeze Frame data stay in the computers memory. Erasing the DTCs from the computers memory can also turn off the MIL. See ERASING DIAGNOSTIC TROUBLE CODES (DTCs) on page 47, before erasing codes from the computers memory. If a Diagnostic Tool or Scan Tool is used to erase the codes, Freeze Frame data will also be erased.
OBD2 MONITORS
To ensure the correct operation of the various emissions-related components and systems, a diagnostic program was developed and installed in the vehicles on-board computer. The program has several procedures and diagnostic strategies. Each procedure or diagnostic strategy is made to monitor the operation of, and run diagnostic tests on, a specific emissions-related component or system. These tests ensure the system is running correctly and is within the manufacturers specifications. On OBD2 systems, these procedures and diagnostic strategies are called Monitors. Currently, fifteen Monitors are supported by OBD2 systems. Additional monitors may be added as a result of Government regulations as the OBD2 system grows and matures. Not all vehicles support all fifteen Monitors. Additionally, some Monitors are supported by spark ignition vehicles only, while others are supported by compression ignition vehicles only. Monitor operation is either Continuous or Non-Continuous, depending on the specific monitor. Continuous Monitors Three of these Monitors are designed to constantly monitor their associated components and/or systems for proper operation. Continuous Monitors run constantly when the engine is running. The Continuous Monitors are: Comprehensive Component Monitor (CCM) Misfire Monitor Fuel System Monitor
OBD2
19
Onboard Diagnostics
OBD2 MONITORS
Non-Continuous Monitors The other twelve Monitors are non-continuous Monitors. Noncontinuous Monitors perform and complete their testing once per trip. The non-continuous Monitors are: Oxygen Sensor Monitor Oxygen Sensor Heater Monitor Catalyst Monitor Heated Catalyst Monitor EGR System Monitor EVAP System Monitor Secondary Air System Monitor The following Monitors became standard beginning in 2010. The majority of vehicles produced before this time will not support these Monitors NMHC Monitor NOx Adsorber Monitor Boost Pressure System Monitor Exhaust Gas Sensor Monitor PM Filter Monitor The following provides a brief explanation of the function of each Monitor: Comprehensive Component Monitor (CCM) - This Monitor continuously checks all inputs and outputs from sensors, actuators, switches and other devices that provide a signal to the computer. The Monitor checks for shorts, opens, out of range value, functionality and rationality. Rationality: Each input signal is compared against all other inputs and against information in the computers memory to see if it makes sense under the current operating conditions. Example: The signal from the throttle position sensor indicates the vehicle is in a wide-open throttle condition, but the vehicle is really at idle, and the idle condition is confirmed by the signals from all other sensors. Based on the input data, the computer determines that the signal from the throttle position sensor is not rational (does not make sense when compared to the other inputs). In this case, the signal would fail the rationality test. The CCM is supported by both spark ignition vehicles and compression ignition vehicles. The CCM may be either a One-Trip or a Two-Trip Monitor, depending on the component.
20
OBD2
Onboard Diagnostics
OBD2 MONITORS
Fuel System Monitor - This Monitor uses a Fuel System Correction program, called Fuel Trim, inside the on-board computer. Fuel Trim is a set of positive and negative values that represent adding or subtracting fuel from the engine. This program is used to correct for a lean (too much air/not enough fuel) or rich (too much fuel/not enough air) air-fuel mixture. The program is designed to add or subtract fuel, as needed, up to a certain percent. If the correction needed is too large and exceeds the time and percent allowed by the program, a fault is indicated by the computer. The Fuel System Monitor is supported by both spark ignition vehicles and compression ignition vehicles. The Fuel System Monitor may be a One-Trip or Two-Trip Monitor, depending on the severity of the problem. Misfire Monitor - This Monitor continuously checks for engine misfires. A misfire occurs when the air-fuel mixture in the cylinder does not ignite. The misfire Monitor uses changes in crankshaft speed to sense an engine misfire. When a cylinder misfires, it no longer contributes to the speed of the engine, and engine speed decreases each time the affected cylinder(s) misfire. The misfire Monitor is designed to sense engine speed fluctuations and determine from which cylinder(s) the misfire is coming, as well as how bad the misfire is. There are three types of engine misfires, Types 1, 2, and 3. - Type 1 and Type 3 misfires are two-trip monitor faults. If a fault is sensed on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The MIL is not commanded on at this time. If the fault is found again on the second trip, under similar conditions of engine speed, load and temperature, the computer commands the MIL On, and the code is saved in its long term memory. - Type 2 misfires are the most severe type of misfire. When a Type 2 misfire is sensed on the first trip, the computer commands the MIL to light when the misfire is sensed. If the computer determines that a Type 2 misfire is severe , and may cause catalytic converter damage, it commands the MIL to flash once per second as soon as the misfire is sensed. When the misfire is no longer present, the MIL reverts to steady On condition. The Misfire Monitor is supported by both spark ignition vehicles and compression ignition vehicles. Catalyst Monitor - The catalytic converter is a device that is installed downstream of the exhaust manifold. It helps to oxidize (burn) the unburned fuel (hydrocarbons) and partially burned fuel (carbon monoxide) left over from the combustion process. To accomplish this, heat and catalyst materials inside the converter react with the exhaust gases to burn the remaining fuel. Some materials inside the catalytic converter also have the ability to store oxygen, and release it as needed to oxidize hydrocarbons and carbon monoxide. In the process, it reduces vehicle emissions by converting the polluting gases into carbon dioxide and water. The computer checks the efficiency of the catalytic converter by monitoring the oxygen sensors used by the system. One sensor is located before (upstream of) the converter; the other is located after (downstream of) the converter. If the catalytic converter loses its ability to store oxygen,
OBD2
21
Onboard Diagnostics
OBD2 MONITORS
the downstream sensor signal voltage becomes almost the same as the upstream sensor signal. In this case, the monitor fails the test. The Catalyst Monitor is supported by spark ignition vehicles only. The Catalyst Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On and saves the code in its long-term memory. Heated Catalyst Monitor - Operation of the heated catalytic converter is similar to the catalytic converter. The main difference is that a heater is added to bring the catalytic converter to its operating temperature more quickly. This helps reduce emissions by reducing the converters down time when the engine is cold. The Heated Catalyst Monitor performs the same diagnostic tests as the catalyst Monitor, and also tests the catalytic converters heater for proper operation. The Heated Catalyst Monitor is supported by spark ignition vehicles only. This Monitor is also a Two-Trip Monitor. Exhaust Gas Recirculation (EGR) Monitor - The Exhaust Gas Recirculation (EGR) system helps reduce the formation of Oxides of Nitrogen during combustion. Temperatures above 2500F cause nitrogen and oxygen to combine and form Oxides of Nitrogen in the combustion chamber. To reduce the formation of Oxides of Nitrogen, combustion temperatures must be kept below 2500F. The EGR system recirculates small amounts of exhaust gas back into the intake manifold, where it is mixed with the incoming air/fuel mixture. This reduces combustion temperatures by up to 500F. The computer determines when, for how long, and how much exhaust gas is recirculated back to the intake manifold. The EGR Monitor performs EGR system function tests at preset times during vehicle operation. The EGR Monitor is supported by both spark ignition vehicles and compression ignition vehicles. The EGR Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory. Evaporative System (EVAP) Monitor - OBD2 vehicles are equipped with a fuel Evaporative system (EVAP) that helps prevent fuel vapors from evaporating into the air. The EVAP system carries fumes from the fuel tank to the engine where they are burned during combustion. The EVAP system may consist of a charcoal canister, fuel tank cap, purge solenoid, vent solenoid, flow monitor, leak detector and connecting tubes, lines and hoses. Fumes are carried from the fuel tank to the charcoal canister by hoses or tubes. The fumes are stored in the charcoal canister. The computer controls the flow of fuel vapors from the charcoal canister to the engine via a purge solenoid. The computer energizes or de-energizes the purge solenoid (depending on solenoid design). The purge solenoid opens a valve to allow engine vacuum to draw the fuel vapors from the canister
22
OBD2
Onboard Diagnostics
OBD2 MONITORS
into the engine where the vapors are burned. The EVAP Monitor checks for proper fuel vapor flow to the engine, and pressurizes the system to test for leaks. The computer runs this Monitor once per trip. The EVAP Monitor is supported by spark ignition vehicles only. The EVAP Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the PCM commands the MIL On, and saves the code in its long-term memory. Oxygen Sensor Heater Monitor - The Oxygen Sensor Heater Monitor tests the operation of the oxygen sensors heater. There are two modes of operation on a computer-controlled vehicle: openloop and closed-loop. The vehicle operates in open-loop when the engine is cold, before it reaches normal operating temperature. The vehicle also goes to open-loop mode at other times, such as heavy load and full throttle conditions. When the vehicle is running in open-loop, the oxygen sensor signal is ignored by the computer for air/fuel mixture corrections. Engine efficiency during open-loop operation is very low, and results in the production of more vehicle emissions. Closed-loop operation is the best condition for both vehicle emissions and vehicle operation. When the vehicle is operating in closed-loop, the computer uses the oxygen sensor signal for air/fuel mixture corrections. In order for the computer to enter closed-loop operation, the oxygen sensor must reach a temperature of at least 600F. The oxygen sensor heater helps the oxygen sensor reach and maintain its minimum operating temperature (600F) more quickly, to bring the vehicle into closed-loop operation as soon as possible. The Oxygen Sensor Heater Monitor is supported by spark ignition vehicles only. The Oxygen Sensor Heater Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory. Oxygen Sensor Monitor - The Oxygen Sensor monitors how much oxygen is in the vehicles exhaust. It generates a varying voltage of up to one volt, based on how much oxygen is in the exhaust gas, and sends the signal to the computer. The computer uses this signal to make corrections to the air/fuel mixture. If the exhaust gas has a large amount of oxygen (a lean air/fuel mixture), the oxygen sensor generates a low voltage signal. If the exhaust gas has very little oxygen (a rich mixture condition), the oxygen sensor generates a high voltage signal. A 450mV signal indicates the most efficient, and least polluting, air/fuel ratio of 14.7 parts of air to one part of fuel. The oxygen sensor must reach a temperature of at least 600-650F, and the engine must reach normal operating temperature, for the computer to enter into closed-loop operation. The oxygen sensor only functions when the computer is in closed-loop. A properly operating oxygen sensor reacts quickly to any change in oxygen content in the
OBD2
23
Onboard Diagnostics
OBD2 MONITORS
exhaust stream. A faulty oxygen sensor reacts slowly, or its voltage signal is weak or missing. The Oxygen Sensor Monitor is supported by spark ignition vehicles only. The Oxygen Sensor Monitor is a Two-Trip monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory. Secondary Air System Monitor - When a cold engine is first started, it runs in open-loop mode. During open-loop operation, the engine usually runs rich. A vehicle running rich wastes fuel and creates increased emissions, such as carbon monoxide and some hydrocarbons. A Secondary Air System injects air into the exhaust stream to aid catalytic converter operation: 1. It supplies the catalytic converter with the oxygen it needs to oxidize the carbon monoxide and hydrocarbons left over from the combustion process during engine warm-up. 2. The extra oxygen injected into the exhaust stream also helps the catalytic converter reach operating temperature more quickly during warm-up periods. The catalytic converter must heat to operating temperature to work properly. The Secondary Air System Monitor checks for component integrity and system operation, and tests for faults in the system. The computer runs this Monitor once per trip. The Secondary Air System Monitor is a Two-Trip monitor. If a fault is found on the first trip, the computer temporarily saves this fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory. Non-Methane Hydrocarbon Catalyst (NMHC) Monitor - The non-methane hydrocarbon catalyst is a type of catalytic converter. It helps to remove non-methane hydrocarbons (NMH) left over from the combustion process from the exhaust stream. To accomplish this, heat and catalyst materials react with the exhaust gases to convert NMH to less harmful compounds. The computer checks the efficiency of the catalyst by monitoring the quantity of NMH in the exhaust stream. The monitor also verifies that sufficient temperature is present to aid in particulate matter (PM) filter regeneration. The NMHC Monitor is supported by compression ignition vehicles only. The NMHC Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory.
24
OBD2
Onboard Diagnostics
OBD2 MONITORS
NOx Aftertreatment Monitor - NOx aftertreatment is based on a catalytic converter support that has been coated with a special washcoat containing zeolites. NOx Aftertreatment is designed to reduce oxides of nitrogen emitted in the exhaust stream. The zeolite acts as a molecular "sponge" to trap the NO and NO2 molecules in the exhaust stream. In some implementations, injection of a reactant before the aftertreatment purges it. NO2 in particular is unstable, and will join with hydrocarbons to produce H2O and N2. The NOx Aftertreatment Monitor monitors the function of the NOx aftertreatment to ensure that tailpipe emissions remain within acceptable limits. The NOx Aftertreatment Monitor is supported by compression ignition vehicles only. The NOx Aftertreatment Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory. Boost Pressure System Monitor - The boost pressure system serves to increase the pressure produced inside the intake manifold to a level greater than atmospheric pressure. This increase in pressure helps to ensure compete combustion of the air-fuel mixture. The Boost Pressure System Monitor checks for component integrity and system operation, and tests for faults in the system. The computer runs this Monitor once per trip. The Boost Pressure System Monitor is supported by compression ignition vehicles only. The Boost Pressure System Monitor is a TwoTrip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory. Exhaust Gas Sensor Monitor - The exhaust gas sensor is used by a number of systems/monitors to determine the content of the exhaust stream. The computer checks for component integrity, system operation, and tests for faults in the system, as well as feedback faults that may affect other emission control systems. The Exhaust Gas Sensor Monitor is supported by compression ignition vehicles only. The Exhaust Gas Sensor Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory.
OBD2
25
Onboard Diagnostics
OBD2 MONITORS
PM Filter Monitor - The particulate matter (PM) filter removes particulate matter from the exhaust stream by filtration. The filter has a honeycomb structure similar to a catalyst substrate, but with the channels blocked at alternate ends. This forces the exhaust gas to flow through the walls between the channels, filtering the particulate matter out. The filters are self-cleaning by periodic modification of the exhaust gas concentration in order to burn off the trapped particles (oxidizing the particles to form CO2 and water). The computer monitors the efficiency of the filter in trapping particulate matter, as well as the ability of the filter to regenerate (self-clean). The PM Filter Monitor is supported by compression ignition vehicles only. The PM Filter Monitor is a Two-Trip Monitor. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The computer does not command the MIL on at this time. If the fault is sensed again on the second trip, the computer commands the MIL On, and saves the code in its long-term memory.
OBD2 Reference Table

The table below lists current OBD2 Monitors, and indicates the following for each Monitor: A. B. C. D. E. F. Monitor Type (how often does the Monitor run; Continuous or Once per trip) Number of trips needed, with a fault present, to set a pending DTC Number of consecutive trips needed, with a fault present, to command the MIL On and store a DTC Number of trips needed, with no faults present, to erase a Pending DTC Number and type of trips or drive cycles needed, with no faults present, to turn off the MIL Number of warm-up periods needed to erase the DTC from the computers memory after the MIL is turned off
26
OBD2
Onboard Diagnostics
OBD2 MONITORS
Name of Monitor Comprehensive Component Monitor Misfire Monitor (Type 1 and 3) Misfire Monitor (Type 2) Fuel System Monitor Catalytic Converter Monitor Oxygen Sensor Monitor Oxygen Sensor Heater Monitor Exhaust Gas Recirculation (EGR) Monitor Evaporative Emissions Controls Monitor Secondary Air System (AIR) Monitor NMHC Monitor NOx Adsorber Monitor Boost Pressure System Monitor Exhaust Gas Sensor Monitor PM Filter Monitor A Continuous Continuous Continuous Continuous Once per trip Once per trip Once per trip Once per trip Once per trip Once per trip Once per trip Once per trip Once per trip Once per trip Once per trip 1 1 1 1 1 B 1 1 C 2 2 1 1 or 2 2 2 2 2 1 1 1 1 1 D 1 1 E 3 3 - similar conditions 3 - similar conditions 3 - similar conditions 3 trips 3 trips 3 trips 3 trips F 40 80 80 80 40 40 40 40
1 1 1 1 1 1 1
2 2 2 2 2 2 2
1 1 1 1 1 1 1
3 trips 3 trips 3 trips 3 trips 3 trips 3 trips 3 trips
40 40 40 40 40 40 40
OBD2
27
Preparation for Testing

PRELIMINARY VEHICLE DIAGNOSTIC WORKSHEET

The purpose of this form is to help you gather preliminary information on your vehicle before you retrieve codes. By having a complete account of your vehicle's current problem(s), you will be able to systematically pinpoint the problem(s) by comparing your answers to the fault codes you retrieve. You can also provide this information to your mechanic to assist in diagnosis and help avoid costly and unnecessary repairs. It is important for you to complete this form to help you and/or your mechanic have a clear understanding of your vehicle's problems. NAME: DATE: VIN*: YEAR: MAKE: MODEL: ENGINE SIZE: VEHICLE MILEAGE: *VIN: Vehicle Identification Number, found at the base of the windshield on a metallic plate, or at the driver door latch area (consult your vehicle owner's manual for location). TRANSMISSION: Automatic Manual Please check all applicable items in each category. DESCRIBE THE PROBLEM:
28
OBD2

WHEN DID YOU FIRST NOTICE THE PROBLEM: Just Started Started Last Week Started Last Month Other:
LIST ANY REPAIRS DONE IN THE PAST SIX MONTHS:
PROBLEMS STARTING No symptoms Will not crank
Cranks, but will not start Starts, but takes a long time
ENGINE QUITS OR STALLS No symptoms Right after starting When shifting into gear During steady-speed driving IDLING CONDITIONS No symptoms Is too slow at all times Is too fast Is sometimes too fast or too slow Is rough or uneven Fluctuates up and down RUNNING CONDITIONS No symptoms Runs rough Lacks power Bucks and jerks Poor fuel economy Hesitates or stumbles on accelerations Backfires Misfires or cuts out Engine knocks, pings or rattles Surges Dieseling or run-on Right after vehicle comes to a stop While idling During acceleration When parking
OBD2
29

AUTOMATIC TRANSMISSION PROBLEMS (if applicable) No symptoms Shifts too early or too late Changes gear incorrectly PROBLEM OCCURS Morning Cold Short - less than 2 miles 2 - 10 miles Long - more than 10 miles Stop and go While turning While braking At gear engagement With A/C operating DRIVING HABITS Mostly city driving Highway Park vehicle inside Park vehicle outside GASOLINE USED 87 Octane 89 Octane 32 - 55 F (0 - 13 C) Below freezing (32 F / 0 C) Sometimes ON PECULIAR SMELLS "Hot" Sulfur ("rotten egg") Burning rubber STRANGE NOISES Rattle Knock Squeak Other Gasoline Burning oil Electrical Always ON 91 Octane More than 91 Octane Above 55 F (13 C) Drive less than 10 miles per day Drive 10 to 50 miles per day Drive more than 50 miles per day Afternoon Warm Vehicle does not move when in gear Jerks or bucks
Anytime Hot With headlights on During acceleration Mostly driving downhill Mostly driving uphill Mostly driving level Mostly driving curvy roads Mostly driving rough roads
ENGINE TEMPERATURE WHEN PROBLEM OCCURS DRIVING CONDITIONS WHEN PROBLEM OCCURS
WEATHER CONDITIONS WHEN PROBLEM OCCURS
CHECK ENGINE LIGHT / DASH WARNING LIGHT Never ON
30
OBD2

BEFORE YOU BEGIN
BEFORE YOU BEGIN

The Enhanced CanOBD2 Diagnostic Tool aids in monitoring electronic- and emissions-related faults in your vehicle and retrieving fault codes related to malfunctions in these systems. Mechanical problems such as low oil level or damaged hoses, wiring or electrical connectors can cause poor engine performance and may also cause a fault code to set. Fix any known mechanical problems before performing any test. See your vehicles service manual or a mechanic for more information. Check the following areas before starting any test: Check the engine oil, power steering fluid, transmission fluid (if applicable), engine coolant and other fluids for proper levels. Top off low fluid levels if needed. Make sure the air filter is clean and in good condition. Make sure all air filter ducts are properly connected. Check the air filter ducts for holes, rips or cracks. Make sure all engine belts are in good condition. Check for cracked, torn, brittle, loose or missing belts. Make sure mechanical linkages to engine sensors (throttle, gearshift position, transmission, etc.) are secure and properly connected. See your vehicles service manual for locations. Check all rubber hoses (radiator) and steel hoses (vacuum/fuel) for leaks, cracks, blockage or other damage. Make sure all hoses are routed and connected properly. Make sure all spark plugs are clean and in good condition. Check for damaged, loose, disconnected or missing spark plug wires. Make sure the battery terminals are clean and tight. Check for corrosion or broken connections. Check for proper battery and charging system voltages. Check all electrical wiring and harnesses for proper connection. Make sure wire insulation is in good condition, and there are no bare wires. Make sure the engine is mechanically sound. If needed, perform a compression check, engine vacuum check, timing check (if applicable), etc.
OBD2
31

VEHICLE SERVICE MANUALS
VEHICLE SERVICE MANUALS

Always refer to the manufacturers service manual for your vehicle before performing any test or repair procedures. Contact your local car dealership, auto parts store or bookstore for availability of these manuals. The following companies publish valuable repair manuals: Haynes Publications 861 Lawrence Drive Newbury Park, California 91320 Phone: 800-442-9637 Web: www.haynes.com Mitchell 1 14145 Danielson Street Poway, California 92064 Phone: 888-724-6742 Web: www.m1products.com Motor Publications 5600 Crooks Road, Suite 200 Troy, Michigan 48098 Phone: 800-426-6867 Web: www.motor.com FACTORY SOURCES Ford, GM, Chrysler, Honda, Isuzu, Hyundai and Subaru Service Manuals Helm Inc. 14310 Hamilton Avenue Highland Park, Michigan 48203 Phone: 800-782-4356 Web: www.helminc.com
32
OBD2
Using the Diagnostic Tool

CODE RETRIEVAL PROCEDURE

Retrieving and using Diagnostic Trouble Codes (DTCs) for troubleshooting vehicle operation is only one part of an overall diagnostic strategy. Never replace a part based only on the DTC definition. Each DTC has a set of testing procedures, instructions and flow charts that must be followed to confirm the location of the problem. This information is found in the vehicle's service manual. Always refer to the vehicle's service manual for detailed testing instructions. Check your vehicle thoroughly before performing any test. See BEFORE YOU BEGIN on page 31 for details. ALWAYS observe safety precautions whenever working on a vehicle. See SAFETY FIRST! on page 3 for more information. 1. Turn the ignition off. 2. Locate the vehicle's 16-pin Data Link Connector (DLC). See page 5 for connector location. Some DLCs have a plastic cover that must be removed before connecting the Diagnostic Tool cable connector. If the Diagnostic Tool is ON, turn it OFF by pressing the POWER/LINK button BEFORE connecting the Diagnostic Tool to the DLC. 3. Connect the Diagnostic Tool cable connector to the vehicles DLC. The cable connector is keyed and will only fit one way. If you have problems connecting the cable connector to the DLC, rotate the connector 180 and try again. If you still have problems, check the DLC on the vehicle and on the Diagnostic Tool. Refer to your vehicles service manual to properly check the vehicles DLC. 4. When the Diagnostic Tools cable connector is properly connected to the vehicles DLC, the unit automatically turns ON, and links to the vehicles onboard computer.
OBD2
33

If the unit does not power on automatically when connected to the vehicles DLC connector, it usually indicates there is no power present at the vehicles DLC connector. Check your fuse panel and replace any burned-out fuses. If replacing the fuse(s) does not correct the problem, consult your vehicles repair manual to identify the proper computer (PCM) fuse/circuit, and perform any necessary repairs before proceeding. 5. Turn the ignition on. DO NOT start the engine. The Diagnostic Tool will automatically start a check of the vehicles computer to determine which type of communication protocol it is using. When the Diagnostic Tool identifies the computers communication protocol, a communication link is established. The protocol type used by the vehicles computer is shown on the LCD display. A PROTOCOL is a set of rules and procedures for regulating data transmission between computers, and between testing equipment and computers. As of this writing, five different types of protocols (ISO 9141, Keyword 2000, J1850 PWM, J1850 VPW and CAN) are in use by vehicle manufacturers. The Diagnostic Tool automatically identifies the protocol type and establishes a communication link with the vehicles computer. 6. After approximately 10~60 seconds, the Diagnostic Tool will retrieve and display any Diagnostic Trouble Codes, Monitor Status and Freeze Frame Data retrieved from the vehicles computer memory. If the Diagnostic Tool fails to link to the vehicles computer a Linking Failed message shows on the Diagnostic Tools LCD display. - Verify the connection at the DLC, and verify the ignition is ON. - Turn the ignition OFF, wait 5 seconds, then turn back ON to reset the computer. - Ensure your vehicle is OBD2 compliant. See VEHICLES COVERED on page 5 for vehicle compliance verification information. The Diagnostic Tool will automatically re-link to the vehicles computer every 30 seconds to refresh the data being retrieved. When data is being refreshed, the message One moment Auto link in progress is shown on the LCD display. This action repeats as long as the Diagnostic Tool is communicating with the vehicles computer.
34
OBD2

The Diagnostic Tool will display a code only if codes are present in the vehicles computer memory. If no codes (including enhanced codes) are present, a No Powertrain DTCs or Freeze Frame Data is presently stored in the vehicles computer message is displayed. - If enhanced codes are present, the Diagnostic Tool enters the enhanced mode (see VIEWING ENHANCED DTCs on page 39). The Diagnostic Tool is capable of retrieving and storing up to 32 codes in memory, for immediate or later viewing. 7. To read the display: Refer to DISPLAY FUNCTIONS on page 9 for a description of LCD display elements. A visible icon indicates that the Diagnostic Tool is being powered through the vehicles DLC connector. A visible icon indicates that the Diagnostic Tool is linked to (communicating with) the vehicles computer. The I/M Monitor Status icons indicate the type and number of Monitors the vehicle supports, and provides indications of the current status of the vehicles Monitors. A solid Monitor icon indicates the associated Monitor has run and completed its testing. A blinking Monitor icon indicates the associated Monitor has not run and completed its testing. The upper right hand corner of the display shows the number of the code currently being displayed, the total number of codes retrieved, the type of code and whether or not the displayed code commanded the MIL on. If the code being displayed is a PENDING code, the PENDING icon is shown. Freeze Frame data is always associated with the Priority Code (identified as Code #1 in the Diagnostic Tools display). If the FREEZE FRAME icon is lit when the Priority Code (Code #1) is displayed on the Diagnostic Tools screen, it indicates that there is Freeze Frame data associated with this code, and the vehicles computer has saved it in its memory. The Diagnostic Trouble Code (DTC) and related code definition are shown in the lower section of the LCD display. In the case of long code definitions, a small arrow is shown in the upper/lower right-hand corner of the code display area to indicate the presence of additional information. Use the and buttons, as necessary, to view the additional information.
OBD2
35

8. Read and interpret Diagnostic Trouble Codes/system condition using the LCD display and the green, yellow and red LEDs. The green, yellow and red LEDs are used (with the LCD display) as visual aids to make it easier to determine engine system conditions. Green LED Indicates that all engine systems are OK and operating normally. All monitors supported by the vehicle have run and performed their diagnostic testing, and no trouble codes are present. A zero will show on the Diagnostic Tools LCD display, and all Monitor icons will be solid. Yellow LED Indicates one of the following conditions: A. PENDING CODE IS PRESENT If the yellow LED is illuminated, it may indicate a Pending code is present. Check the Diagnostic Tools LCD display for confirmation. A Pending code is confirmed by the presence of a numeric code and the word PENDING on the Diagnostic Tools LCD display. MONITOR NOT RUN STATUS If the Diagnostic Tools LCD display shows a zero (indicating there are no DTCs present in the vehicles computer memory), but the yellow LED is illuminated, it may be an indication that some of the Monitors supported by the vehicle have not yet run and completed their diagnostic testing. Check the Diagnostic Tools LCD display for confirmation. All Monitor icons that are blinking have not yet run and completed their diagnostic testing; all Monitor icons that are solid have run and completed their diagnostic testing.
B.
Red LED Indicates there is a problem with one or more of the vehicles systems. The red LED is also used to indicate that DTC(s) are present (displayed on the Diagnostic Tools screen). In this case, the Multifunction Indicator (Check Engine) lamp on the vehicles instrument panel will be illuminated.
36
OBD2

Flashing Red and Yellow LEDs Indicates that a "permanent" code has been set, and one or more of the vehicles monitors has failed its diagnostic testing. A "permanent" DTC can be cleared only by the vehicle's computer following successful completion of the monitor that caused the fault to set. DTCs that start with P0, P2 and some P3 are considered Generic (Universal). All Generic DTC definitions are the same on all OBD2 equipped vehicles. The Diagnostic Tool automatically displays the code definitions for Generic DTCs. DTCs that start with P1 and some P3 are Manufacturer Specific codes and their code definitions vary with each vehicle manufacturer. When a Manufacturer Specific DTC is retrieved, the LCD display shows a list of vehicle manufacturers. Use and DOWN buttons, as necessary, to highlight the the UP button to appropriate manufacturer, then press the ENTER display the correct code definition for your vehicle. A confirmation message shows on the LCD display. - If the correct manufacturer is shown, press the ENTER button to continue. - If the correct manufacturer is not button shown, press the DTC to return to the list of vehicle manufacturers. If the manufacturer for your vehicle is not listed, use the and DOWN buttons, as necessary, to select UP button for Other manufacturer and press the ENTER additional DTC information. If the Manufacturer Specific definition for the currently displayed code is not available, an advisory message shows on the Diagnostic Tools LCD display. 9. If more than one code was retrieved press the DTC button, as necessary, to display additional codes one at a time. Whenever the Scroll function is used to view additional codes, the Diagnostic Tools communication link with the vehicles computer disconnects. To re-establish communication, press the button again. POWER/LINK Each time the DTC button is pressed and released, the Diagnostic Tool will scroll and display the next DTC in sequence until all DTCs in its memory have displayed. Press the FF/M button to view Freeze Frame data.
OBD2
37

In OBD2 systems, when an emissions-related engine malfunction occurs that causes a DTC to set, a record or snapshot of engine conditions at the time that the malfunction occurred is also saved in the vehicles computer memory. The record saved is called Freeze Frame data. Saved engine conditions include, but are not limited to: engine speed, open or closed loop operation, fuel system commands, coolant temperature, calculated load value, fuel pressure, vehicle speed, air flow rate, and intake manifold pressure. If more than one malfunction is present that causes more than one DTC to be set, only the code with the highest priority will contain Freeze Frame data. The code designated 01 on the Diagnostic Tool display is referred to as the PRIORITY code, and Freeze Frame data always refers to this code. The priority code is also the one that has commanded the MIL on. Retrieved information can be uploaded to a Personal Computer (PC) with the use of optional software (see instructions included with the software for more information). Press the DTC button to return to the DTC view screen.
10. When the last retrieved DTC has been displayed and the DTC button is pressed, the Diagnostic Tool enters the enhanced mode. See VIEWING ENHANCED DTCs on page 39 to view enhanced DTCs for your vehicle. 11. Determine engine system(s) condition by viewing the Diagnostic Tools LCD display for any retrieved Diagnostic Trouble Codes, code definitions, Freeze Frame data and interpreting the green, yellow and red LEDs. If DTCs were retrieved and you are going to perform the repairs yourself, proceed by consulting the Vehicles Service Repair Manual for testing instructions, testing procedures, and flow charts related to retrieved code(s). If you plan to take the vehicle to a professional to have it serviced, complete the PRELIMINARY VEHICLE DIAGNOSTIC WORKSHEET on page 28 and take it together with the retrieved codes, freeze frame data and LED information to aid in the troubleshooting procedure. To prolong battery life, the Diagnostic Tool automatically shuts Off approximately three minutes after it is disconnected from the vehicle. The DTCs retrieved, Monitor Status and Freeze Frame data (if any) will remain in the Diagnostic Tools memory, and may be viewed at any time by turning the unit On. If the Diagnostic Tools batteries are removed, or if the Diagnostic Tool is re-linked to a vehicle to retrieve codes/data, any prior codes/data in its memory are automatically cleared.
38
OBD2

VIEWING ENHANCED DTCS
VIEWING ENHANCED DTCs

Following the code retrieval procedure (see CODE RETRIEVAL PROCEDURE on page 33), when the last retrieved DTC has been button is pressed, or if only enhanced DTCs displayed and the DTC were retrieved, the Diagnostic Tool enters the enhanced mode. The enhanced mode provides the ability to retrieve enhanced DTCs from most Chrysler/Jeep, Ford/Mazda, GM/Isuzu, Honda/Acura and Toyota/Lexus vehicles. The types of enhanced data available depend on the vehicle make. The screen shown when the Diagnostic Tool enters the enhanced mode depends on the type(s) of DTC(s) returned during the code retrieval process: If no DTCs were retrieved, or only generic DTCs were retrieved, the Select Manufacturer screen displays. Use the and DOWN buttons, as UP necessary, to highlight the appropriate manufacturer, then press the ENTER button to view the selected information. If a Manufacturer specific DTC was retrieved, and the manufacturer selected for the code was Chrysler, Jeep, Ford, Mazda, General Motors, Isuzu, Honda, Acura, Toyota or Lexus, the Select Data and menu displays. Use the UP buttons, as necessary, to DOWN highlight the desired option, then press the ENTER view the selected information, or, press the FF/M return to the OBD2 DTC screen.
button to button to
If a Manufacturer specific DTC was retrieved, and the manufacturer selected for the code was not Chrysler, Jeep, Ford, Mazda, General Motors, Isuzu, Honda, Acura, Toyota or Lexus the enhanced mode is bypassed, and the OBD2 DTC screen shows the first code retrieved. Enhanced data is not available for your vehicle. Refer to the appropriate paragraph to view enhanced DTCs for your vehicle: Chrysler/Jeep Enhanced DTCs .............page 39 Ford/Mazda Enhanced DTCs ................page 41 GM/Isuzu Enhanced DTCs ....................page 43 Honda/Acura Enhanced DTCs ..............page 44 Toyota/Lexus Enhanced DTCs..............page 46
Chrysler/Jeep Enhanced DTCs

When the Diagnostic Tool enters the enhanced mode (and Chrysler/Jeep is selected, if prompted), the Chrysler Enhanced menu displays. You may view either Engine DTCs or Transmission DTCs.
OBD2
39

1. Use the UP and DOWN buttons, as necessary, to highlight the desired button. option, then press the ENTER Transmission DTCs are not supported on most Chrysler/Jeep vehicles manufactured prior to 2002. A One moment please message displays while the Diagnostic Tool retrieves the selected DTCs. If the Diagnostic Tool fails to link to the vehicles computer, a Linking Failed message shows on the Diagnostic Tools display. Verify the ignition is ON, then press the ENTER continue. button to
2. To read the display: Refer to DISPLAY FUNCTIONS on page 9 for a description of LCD display elements. A visible icon indicates that the Diagnostic Tool is being powered through the vehicles DLC connector. A visible icon indicates that the Diagnostic Tool is linked to (communicating with) the vehicles computer. The upper right hand corner of the display shows the number of the code currently being displayed, the total number of codes retrieved. The Diagnostic Trouble Code (DTC) and related code definition are shown in the lower section of the LCD display. I/M MONITOR STATUS icons are not displayed when viewing enhanced DTCs. In the case of long code definitions, or when viewing Freeze Frame data, a small arrow is shown in the upper/lower right-hand corner of the code display area to indicate the presence of additional information. Use the and buttons, as necessary, to view the additional information. The Diagnostic Tool will display a code only if codes are present in the vehicles computer memory. If no codes are present, a No Enhanced DTCs are presently stored in the vehicles computer is displayed. button to return Press the FF/M to the Chrysler Enhanced menu.
40
OBD2

3. If more than one code was retrieved press the DTC necessary, to display additional codes one at a time.
button, as
Whenever the Scroll function is used to view additional codes, the Diagnostic Tools communication link with the vehicles computer disconnects. To re-establish communication, press the POWER/LINK button again. 4. When the last retrieved DTC has been displayed and the DTC button is pressed, the Diagnostic Tool returns to the Chrysler Enhanced menu. To view additional enhanced DTCs, repeat steps 1 through 4, above. To exit the enhanced mode, press the FF/M Diagnostic Tool returns to the OBD2 DTC screen. button. The
Ford/Mazda Enhanced DTCs

Mazda Enhanced DTCs are available for Mazda-branded Ford vehicles only. When the Diagnostic Tool enters the enhanced mode (and Ford/Mazda is selected, if prompted), the Ford/Mazda Enhanced menu displays. You may view DTCs for either the Continuous Memory Test, KOEO (Key On Engine Off) Test or KOER (Key On Engine Running) Test. 1. Use the UP and DOWN buttons, as necessary, to highlight the desired option, button. then press the ENTER When choosing to view KOER Test DTCs, start the vehicles engine before making your selection. If the Diagnostic Tool fails to link to the vehicles computer, a Linking Failed message shows on the Diagnostic Tools display. - Verify the ignition is ON, then press the ENTER button to continue. If the KOER Test was selected, and the vehicles engine is not running, an advisory message shows on the Diagnostic Tools display. - Start the vehicles engine, then press the ENTER button to continue. 2. An instructional message shows on the Diagnostic Tools display. Perform test procedures as appropriate.
OBD2
41

If the Continuous Memory or KOEO test was selected, turn the ignition OFF, then back ON. Press the button to start the test. ENTER - A One moment please message displays while the test is in progress. If the KOER test was selected, press the ENTER button to continue. - A One moment please message displays while the test is in progress. - Turn the steering wheel to the right, then release. - Press and release the brake pedal. - Cycle the overdrive switch (if equipped). 3. To read the display: Refer to DISPLAY FUNCTIONS on page 9 for a description of LCD display elements. A visible icon indicates that the Diagnostic Tool is being powered through the vehicles DLC connector. A visible icon indicates that the Diagnostic Tool is linked to (communicating with) the vehicles computer. The upper right hand corner of the display shows the number of the code currently being displayed, the total number of codes retrieved. The Diagnostic Trouble Code (DTC) and related code definition are shown in the lower section of the LCD display. I/M MONITOR STATUS icons are not displayed when viewing enhanced DTCs. In the case of long code definitions, or when viewing Freeze Frame data, a small arrow is shown in the upper/lower right-hand corner of the code display area to indicate the presence of additional information. Use the and buttons, as necessary, to view the additional information. The Diagnostic Tool will display a code only if codes are present in the vehicles computer memory. If no codes are present, a No Enhanced DTCs are presently stored in the vehicles computer is displayed. button to return Press the FF/M to the Ford/Mazda Enhanced menu.
42
OBD2

4. If more than one code was retrieved press the DTC necessary, to display additional codes one at a time.
button, as
Whenever the Scroll function is used to view additional codes, the Diagnostic Tools communication link with the vehicles computer disconnects. To re-establish communication, press the POWER/LINK button again. 5. When the last retrieved DTC has been displayed and the DTC button is pressed, the Diagnostic Tool returns to the Ford/Mazda Enhanced menu. To view additional enhanced DTCs, repeat steps 1 through 4, above. To exit the enhanced mode, press the FF/M Diagnostic Tool returns to the OBD2 DTC screen. button. The
General Motors/Isuzu Enhanced DTCs

When the Diagnostic Tool enters the enhanced mode (and GM/Isuzu is selected, if prompted), the GM/Isuzu Enhanced menu displays. You may view the MIL DTC, Current DTC, Fail Since Clear DTC or History DTC. 1. Use the UP and DOWN buttons, as necessary, to highlight the desired button. option, then press the ENTER A One moment please message displays while the Diagnostic Tool retrieves the selected DTCs. If the Diagnostic Tool fails to link to the vehicles computer, a Linking Failed message shows on the Diagnostic Tools display. - Verify the ignition is ON, then press the ENTER button to continue. 2. To read the display: Refer to DISPLAY FUNCTIONS on page 9 for a description of LCD display elements. A visible icon indicates that the Diagnostic Tool is being powered through the vehicles DLC connector. A visible icon indicates that the Diagnostic Tool is linked to (communicating with) the vehicles computer. The upper right hand corner of the display shows the number of the code currently being displayed, the total number of codes retrieved.
OBD2
43

The Diagnostic Trouble Code (DTC) and related code definition are shown in the lower section of the LCD display. I/M MONITOR STATUS icons are not displayed when viewing enhanced DTCs. In the case of long code definitions, or when viewing Freeze Frame data, a small arrow is shown in the upper/lower right-hand corner of the code display area to indicate the presence of additional information. Use the and buttons, as necessary, to view the additional information. The Diagnostic Tool will display a code only if codes are present in the vehicles computer memory. If no codes are present, a No Enhanced DTCs are presently stored in the vehicles computer is displayed. button to return Press the FF/M to the GM Enhanced menu. 3. If more than one code was retrieved press the DTC necessary, to display additional codes one at a time. button, as
Whenever the Scroll function is used to view additional codes, the Diagnostic Tools communication link with the vehicles computer disconnects. To re-establish communication, press the button again. POWER/LINK 4. When the last retrieved DTC has been displayed and the DTC button is pressed, the Diagnostic Tool returns to the GM/Isuzu Enhanced menu. To view additional enhanced DTCs, repeat steps 1 through 4, above. To exit the enhanced mode, press the FF/M Diagnostic Tool returns to the OBD2 DTC screen. button. The
Honda/Acura Enhanced DTCs

When the Diagnostic Tool enters the enhanced mode (and Honda/Acura is selected, if prompted), the Honda/Acura Enhanced menu displays. Depending on the protocol used to communicate with your vehicle, the Honda/Acura Enhanced menu provides options to view: Permanent DTCs or Temporary DTCs Confirmed DTCs or Pending DTCs 1. Use the UP and DOWN buttons, as necessary, to highlight the desired button. option, then press the ENTER A One moment please message displays while the Diagnostic Tool retrieves the selected DTCs.
44
OBD2

If the Diagnostic Tool fails to link to the vehicles computer, a Linking Failed message shows on the Diagnostic Tools display. Verify the ignition is ON, then press the ENTER button to continue. Refer to DISPLAY FUNCTIONS on page 9 for a description of LCD display elements. A visible icon indicates that the Diagnostic Tool is being powered through the vehicles DLC connector. A visible icon indicates that the Diagnostic Tool is linked to (communicating with) the vehicles computer. The upper right hand corner of the display shows the number of the code currently being displayed, the total number of codes retrieved. The Diagnostic Trouble Code (DTC) and related code definition are shown in the lower section of the LCD display. I/M MONITOR STATUS icons are not displayed when viewing enhanced DTCs. In the case of long code definitions, or when viewing Freeze Frame data, a small arrow is shown in the upper/lower right-hand corner of the code display area to indicate the presence of additional information. Use the and buttons, as necessary, to view the additional information. The Diagnostic Tool will display a code only if codes are present in the vehicles computer memory. If no codes are present, a No Enhanced DTCs are presently stored in the vehicles computer is displayed. Press the FF/M button to return to the Honda/Acura Enhanced menu. 3. If more than one code was retrieved press the DTC necessary, to display additional codes one at a time. button, as
2. To read the display:
Whenever the Scroll function is used to view additional codes, the Diagnostic Tool communication link with the vehicles computer disconnects. To re-establish communication, press the button again. POWER/LINK
OBD2
45

4. When the last retrieved DTC has been displayed and the DTC button is pressed, the Diagnostic Tool returns to the Honda/Acura Enhanced menu. To view additional enhanced DTCs, repeat steps 1 through 4, above. To exit the enhanced mode, press the FF/M Diagnostic Tool returns to the OBD2 DTC screen. button. The
Toyota/Lexus Enhanced DTCs

When the Diagnostic Tool enters the enhanced mode (and Toyota/Lexus is selected, if prompted), the Toyota/Lexus Enhanced menu displays. Depending on the protocol used to communicate with your vehicle, the Toyota/Lexus Enhanced menu provides options to view: Current DTCs, History DTCs or Pending DTCs Current DTCs, Historical Readiness DTCs DTCs or
1. Use the UP and DOWN buttons, as necessary, to highlight the desired button. option, then press the ENTER A One moment please message displays, while the Diagnostic Tool retrieves the selected DTCs. If the Diagnostic Tool fails to link to the vehicles computer, a Linking Failed message shows on the Diagnostic Tools Display. - Verify the ignition is ON, then press the ENTER button to continue. 2. To read the display: Refer to DISPLAY FUNCTIONS on page 9 for a description of LCD display elements. A visible icon indicates that the Diagnostic Tool is being powered through the vehicles DLC connector. A visible icon indicates that the Diagnostic Tool is linked to (communicating with) the vehicles computer. The upper right hand corner of the display shows the number of the code currently being displayed, the total number of codes retrieved. The Diagnostic Trouble Code (DTC) and related code definition are shown in the lower section of the LCD display.
46
OBD2

ERASING DIAGNOSTIC TROUBLE CODES (DTCs)
I/M MONITOR STATUS icons are not displayed when viewing enhanced DTCs. In the case of long code definitions, or when viewing Freeze Frame data, a small arrow is shown in the upper/lower right-hand corner of the code display area to indicate the presence of additional information. Use and buttons, as necessary, to view the the additional information. The Diagnostic Tool will display a code only if codes are present in the vehicles computer memory. If no codes are present, a No Enhanced DTCs are presently stored in the vehicles computer is displayed. button to return Press the FF/M to the Toyota/Lexus Enhanced menu. 3. If more than one code was retrieved press the DTC necessary, to display additional codes one at a time. button, as
Whenever the Scroll function is used to view additional codes, the Diagnostic Tools communication link with the vehicles computer disconnects. To re-establish communication, press the button again. POWER/LINK 4. When the last retrieved DTC has been displayed and the DTC button is pressed, the Diagnostic Tool returns to the Toyota/Lexus Enhanced menu. To view additional enhanced DTCs, repeat steps 1 through 4, above. To exit the enhanced mode, press the FF/M Diagnostic Tool returns to the OBD2 DTC screen. button. The

When the Diagnostic Tools ERASE function is used to erase DTCs from the vehicle's on-board computer, "Freeze Frame" data and manufacturer-specific-enhanced data are also erased. "Permanent" DTCs ARE NOT erased by the ERASE function. If you plan to take the vehicle to a Service Center for repair, DO NOT erase the codes from the vehicle's computer. If the codes are erased, valuable information that might help the technician troubleshoot the problem will also be erased.
OBD2
47

Erase DTCs from the computer's memory as follows: When DTCs are erased from the vehicle's computer memory, the I/M Readiness Monitor Status program resets the status of all Monitors to a not run "flashing" condition. To set all of the Monitors to a DONE status, an OBD2 Drive Cycle must be performed. Refer to your vehicle's service manual for information on how to perform an OBD2 Drive Cycle for the vehicle under test. The Diagnostic Tool must be connected to the vehicles DLC to erase the codes from the computers memory. If you press the ERASE button when the Diagnostic Tool is not connected to the vehicles DLC, the erase instruction screen displays. 1. If not connected already, connect the Diagnostic Tool to the vehicle's DLC, and turn the ignition "On. (If the Diagnostic Tool is already connected and linked to the vehicle's computer, proceed directly to step 3. If not, continue to step 2.) 2. Perform the Code Retrieval procedure as described on page 19. Wait until the codes are displayed on the Diagnostic Tools LCD and then proceed to step 3. 3. Press and release the ERASE button. A confirmation message shows on the LCD display. If you are sure you want to proceed, and DOWN use the UP buttons, as necessary, to highlight YES, then press the ENTER button to erase DTCs from the vehicles computer. If you do not want to continue with the erase process, use the and DOWN buttons, as necessary, to highlight NO, UP button to exit the erase mode. then press the ENTER 4. If you chose to erase DTCs, a progress screen displays while the erase function is in progress. If the erase was successful, a confirmation message shows on the display. Press the POWER/LINK button to return to the DTC screen.
48
OBD2

I/M READINESS TESTING
If the erase was not successful, an advisory message shows on the display. Verify that the Diagnostic Tool is properly connected to the vehicles DLC and that the ignition is on, then repeat steps 2 and 3, above. Erasing DTCs does not fix the problem(s) that caused the code(s) to be set. If proper repairs to correct the problem that caused the code(s) to be set are not made, the code(s) will appear again (and the check engine light will illuminate) as soon as the vehicle is driven long enough for its Monitors to complete their testing.

I/M is an Inspection and Maintenance program legislated by the Government to meet federal clean-air standards. The program requires that a vehicle be taken periodically to an Emissions Station for an "Emissions Test" or "Smog Check, where the emissions-related components and systems are inspected and tested for proper operation. Emissions Tests are generally performed once a year, or once every two years. On OBD2 systems, the I/M program is enhanced by requiring vehicles to meet stricter test standards. One of the tests instituted by the Federal Government is called I/M 240. On I/M 240, the vehicle under test is driven under different speeds and load conditions on a dynamometer for 240 seconds, while the vehicle's emissions are measured. Emissions tests vary depending on the geographic or regional area in which the vehicle is registered. If the vehicle is registered in a highly urbanized area, the I/M 240 is probably the type of test required. If the vehicle is registered in a rural area, the stricter dynamometer type test may not be required. I/M Readiness Monitors I/M Readiness shows whether the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing. State and Federal Governments enacted Regulations, Procedures and Emission Standards to ensure that all emissions-related components and systems are continuously or periodically monitored, tested and diagnosed whenever the vehicle is in operation. It also requires vehicle manufacturers to automatically detect and report any problems or faults that may increase the vehicle's emissions to an unacceptable level. The vehicle's emissions control system consists of several components or sub-systems (Oxygen Sensor, Catalytic Converter, EGR, Fuel System, etc.) that aid in reducing vehicle emissions. To have an efficient Vehicle Emission Control System, all the emissionsrelated components and systems must work correctly whenever the vehicle is in operation.
OBD2
49

To comply with State and Federal Government regulations, vehicle manufacturers designed a series of special computer programs called "Monitors" that are programmed into the vehicle's computer. Each of these Monitors is specifically designed to run tests and diagnostics on a specific emissions-related component or system (Oxygen Sensor, Catalytic Converter, EGR Valve, Fuel System, etc.) to ensure their proper operation. Currently, there are a maximum of eleven Monitors available for use. To learn more about Emissions Inspection and Maintenance (I/M) Readiness Monitors, see OBD2 MONITORS on page 23.
Each Monitor has a specific function to test and diagnose only its designated emissionsrelated component or system. The names of the Monitors (Oxygen Sensor Monitor, Catalyst Monitor, EGR Monitor, Misfire Monitor, etc.) describe which component or system each Monitor is designed to test and diagnose. Emissions Inspection and Maintenance (I/M) Readiness Monitor Status Information I/M Readiness Monitor Status shows which of the vehicle's Monitors have run and completed their diagnosis and testing, and which ones have not yet run and completed testing and diagnosis of their designated sections of the vehicle's emissions system. If a Monitor was able to meet all the conditions required to enable it to perform the self-diagnosis and testing of its assigned engine system, it means the monitor "HAS RUN. If a Monitor has not yet met all the conditions required for it to perform the self-diagnosis and testing of its assigned engine system; it means the Monitor "HAS NOT RUN. The Monitor Run/Not Run status does not show whether or not a problem exists in a system. Monitor status only indicates whether a particular Monitor has or has not run and performed the self-diagnosis and testing of its associated system. Performing I/M Readiness Quick Check When a vehicle first comes from the factory, all Monitors indicate a HAVE RUN status. This indicates that all Monitors have run and completed their diagnostic testing. The HAVE RUN status remains in the computer's memory, unless the Diagnostic Trouble Codes are erased or the vehicle's computer memory is cleared.
50
OBD2

The Diagnostic Tool allows you to retrieve Monitor/System Status Information to help you determine if the vehicle is ready for an Emissions Test (Smog Check). In addition to retrieving Diagnostic Trouble Codes, the Diagnostic Tool also retrieves Monitor Run/Not Run status. This information is very important since different areas of the state/country have different emissions laws and regulations concerning Monitor Run/Not Run status. Before an Emissions Test (Smog Check) can be performed, your vehicle must meet certain rules, requirements and procedures legislated by the Federal and state (country) governments where you live. 1. In most areas, one of the requirements that must be met before a vehicle is allowed to be Emissions Tested (Smog Checked) is that the vehicle does not have any Diagnostic Trouble Codes present (with the exception of PENDING Diagnostic Trouble Codes). 2. In addition to the requirement that no Diagnostic Trouble Codes be present, some areas also require that all the Monitors that a particular vehicle supports indicate a "Has Run" status condition before an Emissions Check may be performed. 3. Other areas may only require that some (but not all) Monitors indicate a "Has Run" status before an Emissions Test (Smog Check) may be performed. Monitors with a "Has Run" status indicate that all the required conditions they needed to perform diagnosis and testing of their assigned engine area (system) have been met, and all diagnostic testing has completed successfully. Monitors with a "Has Not Run" status have not yet met the conditions they need to perform diagnosis and testing of their assigned engine area (system), and have not been able to perform diagnostic testing on that system. The green, yellow and red LEDs provide a quick way to help you determine if a vehicle is ready for an Emissions Test (Smog Check). Follow the instructions below to perform the Quick Check. Perform the CODE RETRIEVAL PROCEDURE as described on page 33, then interpret the LED indications as follows:
Interpreting I/M Readiness Test Results

1. GREEN LED - Indicates that all engine systems are "OK" and operating normally (all Monitors supported by the vehicle have run and performed their self-diagnostic testing). The vehicle is ready for an Emissions Test (Smog Check), and there is a good possibility that it can be certified. 2. YELLOW LED - Determine from the CODE RETRIEVAL PROCEDURE (page 33) which of the two possible conditions is causing the yellow LED to light.
OBD2
51

If a "PENDING" Diagnostic Trouble Code is causing the yellow LED to light, it is possible that the vehicle will be allowed to be tested for emissions and certified. Currently, most areas (states / countries) will allow an Emissions Test (Smog Check) to be performed if the only code in the vehicle's computer is a "PENDING" Diagnostic Trouble Code. If the illumination of the Yellow LED is being caused by monitors that have not run their diagnostic testing, then the issue of the vehicle being ready for an Emissions Test (Smog Check) depends on the emissions regulations and laws of your local area. - Some areas require that all Monitors indicate a "Has Run" status before they allow an Emissions Test (Smog Check) to be performed. Other areas only require that some, but not all, Monitors have run their selfdiagnostic testing before an Emissions Test (Smog Check) may be performed. From the code retrieval procedure, determine the status of each Monitor (a solid Monitor icon shows Monitor "Has Run" status, a flashing Monitor icon indicates "Has Not Run" status). Take this information to an emissions professional to determine (based on your test results) if your vehicle is ready for an Emissions Test (Smog Check). 3. RED LED - Indicates there is a problem with one or more of the vehicle's systems. A vehicle displaying a red LED is definitely not ready for an Emissions Test (Smog Check). The red LED is also an indication that there are Diagnostic Trouble Code(s) present (displayed on the Diagnostic Tool's screen). The Multifunction Indicator (Check Engine) Lamp on the vehicle's instrument panel will light steady. The problem that is causing the red LED to light must be repaired before an Emissions Test (Smog Check) can be performed. It is also suggested that the vehicle be inspected/repaired before driving the vehicle further. 4. Flashing Red and Yellow LEDs Indicates that a "permanent" code has been set, and one or more of the vehicles monitors has failed its diagnostic testing. A "permanent" DTC can be cleared only by the vehicle's computer following successful completion of the monitor that caused the fault to set. If the Red LED or flashing RED and YELLOW LEDs were obtained, there is a definite problem present in the system(s). In these cases, you have the following options.
52
OBD2

Repair the vehicle yourself. If you are going to perform the repairs yourself, proceed by reading the vehicle service manual and following all its procedures and recommendations. Take the vehicle to a professional to have it serviced. The problem(s) causing the red LED to light must be repaired before the vehicle is ready for an Emissions Test (Smog Check). On some vehicle models, the computer will store non-emission related DTCs. These DTCs will not command the MIL on since they are not emission related. If the Diagnostic Tool retrieves one of these types of codes, the MIL will not be commanded on, and the Yellow LED on the Diagnostic Tool will be illuminated. In most cases, these types of codes will not prevent the Emissions Test from being performed. Using the I/M Readiness Monitor Status to Confirm a Repair The I/M Readiness Monitor Status function can be used (after repair of a fault has been performed) to confirm that the repair has been performed correctly, and/or to check for Monitor Run Status. Use the following procedure to determine I/M Readiness Monitor Status: 1. Using retrieved Diagnostic Trouble Codes (DTCs) and code definitions as a guide, and following manufacturer's repair procedures, repair the fault or faults as instructed. 2. After the fault or faults have been repaired, connect the Diagnostic Tool to the vehicle's DLC and erase the code or codes from the vehicle's computer memory. See page 47 for procedures for ERASING DIAGNOSTIC TROUBLE CODES (DTCs) from the vehicle's on-board computer. Write the codes down on a piece of paper for reference before erasing. 3. After the erase procedure is performed, most of the Monitor icons on the Diagnostic Tools LCD display will be flashing. Leave the Diagnostic Tool connected to the vehicle, and perform a Trip Drive Cycle for each "flashing" Monitor: Misfire, Fuel and Comprehensive Component Monitors run continuously and their icons will always be on solid, even after the erase function is performed. Each DTC is associated with a specific Monitor. Consult the vehicle's service manual to identify the Monitor (or Monitors) associated with the faults that were repaired. Follow the manufacturer's procedures to perform a Trip Drive Cycle for the appropriate Monitors. While observing the Monitor icons on the Diagnostic Tools LCD display, perform a Trip Drive Cycle for the appropriate Monitor or Monitors.
OBD2
53

If the vehicle needs to be driven in order to perform a Trip Drive Cycle, ALWAYS have a second person help you. One person should drive the vehicle while the other person observes the Monitor icons on the Diagnostic Tool for Monitor RUN status. Trying to drive and observe the Diagnostic Tool at the same time is dangerous, and could cause a serious traffic accident. 4. When a Monitor's Trip Drive Cycle is performed properly, the Monitor icon on the Diagnostic Tools LCD display changes from "flashing" to "solid, indicating that the Monitor has run and finished its diagnostic testing. If, after the Monitor has run, the MIL on the vehicle's dash is not lit, and no stored or pending codes associated with that particular Monitor are present in the vehicle's computer, the repair was successful. If, after the Monitor has run, the MIL on the vehicle's dash lights and/or a DTC associated with that Monitor is present in the vehicle's computer, the repair was unsuccessful. Refer to the vehicle's service manual and recheck repair procedures.
54
OBD2
Additional Functions
VIEWING VEHICLE INFORMATION

The Scan Tool offers three options for retrieving reference information for the vehicle under test; Vehicle ID, Available Modules and IPT (Inuse Performance Tracking).
Retrieving Vehicle ID Information

The Vehicle ID function is applicable to model year 2000 and newer OBD2-compliant vehicles. The Diagnostic Tool can retrieve a list of information (provided by the vehicle manufacturer), unique to the vehicle under test, from the vehicle's on-board computer. This information may include: The vehicle's VIN number The control module identification number The vehicle's calibration ID(s). These IDs uniquely identify the software version(s) for the vehicle's control module(s). The Vehicle's Calibration Verification Number(s) (CVNs) required by ODB2 regulations. CVNs are used to determine if emission-related calibrations for the vehicle under test have been changed. One or more CVNs may be returned by the vehicle's computer. 1. While linked to a vehicle, press and hold the FF/M button until the Menu appears. 2. Use the UP and DOWN buttons, as necessary, to highlight Vehicle Info, then press the ENTER button. The Vehicle Info Menu displays. and DOWN buttons, 3. Use the UP as necessary, to highlight Vehicle ID, then press the ENTER button. 4. A "One moment please..." message displays while the requested information is retrieved from the vehicle's computer. The first time the Vehicle ID function is used, it may take several minutes to retrieve the information from the vehicle's computer. 5. When the retrieval process is completed, the vehicle ID information is shown on the Diagnostic Tools display. Use the and DOWN buttons, as UP necessary, to view the entire list. 6. When you have finished viewing the retrieved vehicle ID information, press the FF/M button to exit.
OBD2
55
Viewing Available Modules

The Diagnostic Tool can retrieve a list of modules supported by the vehicle under test. 1. While linked to a vehicle, press and hold the FF/M the Menu appears. 2. Use the UP and DOWN buttons, as necessary, to highlight Vehicle Info, button. then press the ENTER The Vehicle Info Menu displays. and DOWN buttons, 3. Use the UP as necessary, to highlight Available Modules, then press the ENTER button. 4. A "One moment please..." message displays while the requested information is retrieved from the vehicle's computer. 5. When the retrieval process is completed, a complete list of modules supported by the vehicle under test is shown on the Diagnostic Tools display. Use the UP and DOWN buttons, as necessary, to view the entire list. 6. When you have finished viewing the list of available modules, press the FF/M button to exit. Viewing In-use Performance Tracking (IPT) The Diagnostic Tool can retrieve In-use Performance Tracking (IPT) statistics for monitors supported by the vehicle under test. Two values are returned for each monitor; the number of times that all conditions necessary for a specific monitor to detect a malfunction have been encountered (XXXCOND), and the number of times that the vehicle has been operated under the specific conditions for the monitor (XXXCOMP). Statistics are also provided for the number of times the vehicle has been operated in OBD monitoring conditions (OBDCOND), and the number of times the vehicles engine has been started (IGNCNTR). 1. While linked to a vehicle, press and hold the FF/M button until the Menu appears. 2. Use the UP and DOWN buttons, as necessary, to highlight Vehicle Info, button. then press the FF/M button until
56
OBD2
ADJUSTMENT/SETTINGS AND DTC LIBRARY
The Vehicle Info Menu displays. and DOWN buttons, 3. Use the UP as necessary, to highlight IPT, then press the ENTER button. 4. A One moment please . . . message displays while the requested information is retrieved from the vehicles computer. If In-use Performance Tracking is not supported by the vehicle under test, an advisory message shows on the Diagnostic Tools button to exit. display. Press the FF/M 5. When the retrieval process is completed, In-use Performance Tracking statistics for monitors supported by the vehicle under test are shown on the Scan Tools and DOWN display. Use the UP buttons, as necessary, to view the entire list. 6. When you have finished viewing the statistics, press the FF/M button to exit.
ADJUSTMENTS/SETTINGS AND DTC LIBRARY

The Diagnostic Tool lets you make several adjustments and settings to configure the Diagnostic Tool to your particular needs. It also contains an OBD2 DTC Library that allows you to search for DTC definitions. The following functions, adjustments and settings can be performed when the Diagnostic Tool is in MENU Mode: Adjust Brightness: Adjusts the brightness of the LCD display screen. Audible Tone: Turns the Diagnostic Tools audible tone on and off. When turned on, a tone sounds each time a button is pressed. Display Backlight: Turns the display backlight on and off. DTC Library: Lets you search the library of OBD2 DTC definitions. Firmware Version: Displays the Diagnostic Tools firmware version. Select Language: Sets the display language for the Diagnostic Tool to English, French or Spanish. Unit of Measurement: Sets the Unit of Measurement for the Diagnostic Tools display to USA or Metric. Adjustments and settings can be made only when the Diagnostic Tool is NOT connected to a vehicle.
OBD2
57
To enter the MENU Mode: 1. With the Diagnostic Tool on the Code Retrieval screen, press and hold the button until the Menu FF/M appears. 2. Use the UP and DOWN buttons, as necessary, to highlight Tool Setting, button. then press the ENTER The Tool Setting Menu displays. 3. Make adjustments and settings as described in the following paragraphs. Adjusting Display Brightness 1. Use the UP and DOWN buttons, as necessary, to highlight Adjust Brightness in the Menu, then press the button. ENTER The Adjust Brightness screen displays. The Brightness field shows the current brightness setting, from 1-4. button to decrease the 2. Press the UP brightness of the LCD display (make the display darker). 3. Press the DOWN button to increase the brightness of the LCD display (make the display lighter). 4. When the desired brightness is obtained, press the ENTER button to save your changes and return to the Menu. To exit the Adjust Brightness screen and return to the button. Menu without making changes, press the FF/M Enabling the Audible Tone and DOWN buttons, 1. Use the UP as necessary, to highlight Audible Tone in the Menu, then press the ENTER button. The Audible Tone screen displays. 2. Press the UP or DOWN button, as necessary, to highlight ON or OFF as desired.
58
OBD2
3. When the desired option is selected, press the ENTER save your changes and return to the Menu.
button to
To exit the Audible Tone screen and return to the Menu without making changes, press the FF/M button. Using the Backlight 1. Use the UP and DOWN buttons, as necessary, to highlight Display Backlight in the Menu, then press the ENTER button. The Display Backlight screen displays. 2. Press the UP or DOWN button, as necessary, to select the desired backlight mode, either ON or OFF. 3. When the desired backlight mode is button to selected, press the ENTER save your changes. The display returns to the Menu, and the backlight turns on or off as selected. To exit the Display Backlight screen and return to the Menu button. without making changes, press the FF/M Searching for a DTC Definition Using the DTC Library 1. Use the UP and DOWN buttons, as necessary, to highlight DTC Library in the Menu, then press the ENTER button. The Enter DTC screen displays. The screen shows the code P0001, with the P highlighted. 2. Use the UP and DOWN buttons, as necessary, to scroll to the desired DTC type (P=Powertrain, U=Network, B=Body, C=Chassis), then press the button. DTC The selected character displays solid, and the next character is highlighted. 3. Select the remaining characters in the DTC in the same way, pressing the DTC button to confirm each character. When you button have selected all the DTC characters, press the ENTER to view the DTC definition.
OBD2
59
If you entered a Generic DTC (DTCs that start with P0, P2 and some P3): - The selected DTC and DTC definition (if available), show on the Diagnostic Tools LCD display. If you entered a ManufacturerSpecific DTC (DTCs that start with P1 and some P3): - The Select Manufacturer screen displays. - Use the UP and DOWN buttons, as necessary, to highlight the appropriate manufacturer, then button to press the ENTER display the correct DTC for your vehicle. If a definition for the DTC you entered is not available, an advisory message shows on the Diagnostic Tools display. 4. If you wish to view definitions for additional DTCs, press the ENTER button to return to the DTC Library screen, and repeat steps 2 and 3. 5. When all desired DTCs have been viewed, press the FF/M button to exit the DTC Library. Viewing the Firmware Version and DOWN buttons, 1. Use the UP as necessary, to highlight Firmware Version in the Menu, then press the ENTER button. The Firmware Version screen displays. The screen shows the Diagnostic Tools current firmware version. 2. Press the FF/M the Menu. button to return to
Selecting the Display Language and DOWN buttons, 1. Use the UP as necessary, to highlight Select Language in the Menu, then press the button. ENTER
60
OBD2
The Select Language screen displays. The currently selected Language is highlighted. display
2. Press the UP or DOWN button, as necessary, to highlight the desired display language. 3. When the desired display language is highlighted, press the ENTER button to save your changes and return to the Menu (shown in the selected display language). To exit the Select Language screen and return to the Menu without making changes, press the FF/M button. Setting the Unit of Measurement and DOWN buttons, 1. Use the UP as necessary, to highlight Unit of Measurement in the Menu, then press the ENTER button. The Unit of Measurement screen displays. The currently selected Unit Measurement is highlighted. of
2. Press the UP or DOWN button, as necessary, to highlight the desired Unit of Measurement. 3. When the desired Unit of Measurement value is selected, press the ENTER button to save your changes and return to the Menu. To exit the Unit of Measurement screen and return to the button. Menu without making changes, press the FF/M Exiting the MENU Mode 1. Press the FF/M button.
The LCD display returns to the DTC screen (if data is currently stored in the Diagnostic Tools memory) or the To Link screen (if no data is stored).
OBD2
61
Generic (Global) OBD2 PID List

The following is a list of Generic (Global) PIDs and their descriptions. Tool Display ACC Pedal D ACC Pedal E ACC Pedal F Air Status Ambient Aux Input Status BARO Calc LOAD CAT Temp 11 CAT Temp 12 CAT Temp 21 CAT Temp 22 Command EGR Command EVAP Command TAC Dist DTC Clr Dist MIL ON Unit % % % *C / *F kPa /inHg % *C / *F *C / *F *C / *F *C / *F % % % km /mile km /mile s *C / *F V % min Value XXX.X XXX.X XXX.X UPS, DNS, OFF XXX On / Off XXX / XX.X XXX.X XXXX.X XXXX.X XXXX.X XXXX.X XXX.X XXX.X XXX.X XXXXX XXXXX PID Description Accelerator Pedal Position D Accelerator Pedal Position E Accelerator Pedal Position F Commanded Secondary Air Status Ambient Air Temperature Auxiliary Input Status Barometric Pressure Calculated LOAD Value Catalyst Temperature Bank 1Sensor 1 Catalyst Temperature Bank 1Sensor 2 Catalyst Temperature Bank 2Sensor 1 Catalyst Temperature Bank 2Sensor 2 Commanded EGR Commanded Evaporative Purge Commanded Throttle Actuator Distance since DTC Cleared Distance Traveled while MIL ON
ECT ECU Volts EGR Error Eng RPM EQ Ratio EQ Ratio 11 EQ Ratio 12 EQ Ratio 13 EQ Ratio 14
XXX / XXX XX.XXX XXX.X XXXXX X.XXX X.XXX X.XXX X.XXX X.XXX
Engine Coolant Temp Control Module Voltage EGR Error Engine RPM Commanded Equivalence Ratio Bank 1 - Sensor 1 Equivalence Ratio Bank 1 - Sensor 2 Equivalence Ratio Bank 1 - Sensor 3 Equivalence Ratio Bank 1 - Sensor 4 Equivalence
62
OBD2

Tool Display EQ Ratio 21 EQ Ratio 22 EQ Ratio 23 EQ Ratio 24 EVAP Press
Unit Pa /in H2O kPa /PSI % kPa /PSI kPa /PSI *C / *F % % % % % g/s ;l b/min kPa /PSI hrs, min V mA
Value X.XXX X.XXX X.XXX X.XXX XXXX.XX /XX.XXX XXXX.XXX /XXX.X XXX.X XXX / XX.X XXXXX /XXXX.X OL CL OL-Drive OL-Fault CL-Fault OL CL OL-Drive OL-Fault CL-Fault XXX / XXX XXX.X XXX.X XXX.X XXX.X XXX.X XXX.XX /XXXX.X XXX / XX.X XXXX, XX ICONS on Display X.XXX X.XXX
PID Description Ratio Bank 2 - Sensor 1 Equivalence Ratio Bank 2 - Sensor 2 Equivalence Ratio Bank 2 - Sensor 3 Equivalence Ratio Bank 2 - Sensor 4 Equivalence Ratio Evap System Vapor Pressure
FP / Vac Fuel Level Fuel Press Fuel Press Fuel Sys 1 Fuel Sys 1 Fuel Sys 1 Fuel Sys 1 Fuel Sys 1 Fuel Sys 2 Fuel Sys 2 Fuel Sys 2 Fuel Sys 2 Fuel Sys 2 IAT LOAD Value LTFT B1 LTFT B2 LTFT B3 LTFT B4 MAF MAP MIL On Time Monitor Status O2S B1 S1 O2S B1 S1
Fuel Rail Pressure relative toVacuum Fuel Level Input Fuel Rail Pressure Fuel Rail Pressure Fuel System 1 Status Fuel System 1 Status Fuel System 1 Status Fuel System 1 Status Fuel System 1 Status Fuel System 2 Status Fuel System 2 Status Fuel System 2 Status Fuel System 2 Status Fuel System 2 Status Intake Air Temperature Absolute Load Value Long Term Fuel Trim-Bank 1 Long Term Fuel Trim-Bank 2 Long Term Fuel Trim-Bank 3 Long Term Fuel Trim-Bank 4 Air Flow Rate from Mass Air Flow Sensor Intake Manifold Absolute Pressure Engine Run Time while MIL ON Monitor Status this Driving Cycle Bank 1 - Sensor 1 Bank 1 - Sensor 1 O2S Current
OBD2
63

Tool Display mA O2S B1 S1 V O2S B1 S2 O2S B1 S2 mA O2S B1 S2 V O2S B1 S3 O2S B1 S3 mA O2S B1 S3 V O2S B1 S4 O2S B1 S4 mA O2S B1 S4 V O2S B2 S1 O2S B2 S1 mA O2S B2 S1 V O2S B2 S2 O2S B2 S2 mA O2S B2 S2 V O2S B2 S3 O2S B2 S3 mA O2S B2 S3 V O2S B2 S4 O2S B2 S4 mA O2S B2 S4 V O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location O2S Location
Unit V V mA V V mA V V mA V V mA V V mA V V mA V V mA V -
Value X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX X.XXX O2S11 O2S12 O2S13 O2S14 O2S21 O2S22 O2S23 O2S24 O2S11 O2S12 O2S21 O2S22 O2S31 O2S32 O2S41 O2S42
PID Description Bank 1 - Sensor 1 O2S Voltage Bank 1 - Sensor 2 Bank 1 - Sensor 2 O2S Current Bank 1 - Sensor 2 O2S Voltage Bank 1 - Sensor 3 Bank 1 - Sensor 3 O2S Current Bank 1 - Sensor 3 O2S Voltage Bank 1 - Sensor 4 Bank 1 - Sensor 4 O2S Current Bank 1 - Sensor 4 O2S Voltage Bank 2 - Sensor 1 Bank 2 - Sensor 1 O2S Current Bank 2 - Sensor 1 O2S Voltage Bank 2 - Sensor 2 Bank 2 - Sensor 2 O2S Current Bank 2 - Sensor 2 O2S Voltage Bank 2 - Sensor 3 Bank 2 - Sensor 3 O2S Current Bank 2 - Sensor 3 O2S Voltage Bank 2 - Sensor 4 Bank 2 - Sensor 4 O2S Current Bank 2 - Sensor 4 O2S Voltage Oxygen Sensor, Bank 1, Sensor 1 Oxygen Sensor, Bank 1, Sensor 2 Oxygen Sensor, Bank 1, Sensor 3 Oxygen Sensor, Bank 1, Sensor 4 Oxygen Sensor, Bank 2, Sensor 1 Oxygen Sensor, Bank 2, Sensor 1 Oxygen Sensor, Bank 2, Sensor 3 Oxygen Sensor, Bank 2, Sensor 4 Oxygen Sensor, Bank 1, Sensor 1 Oxygen Sensor, Bank 1, Sensor 2 Oxygen Sensor, Bank 2, Sensor 1 Oxygen Sensor, Bank 2, Sensor 2 Oxygen Sensor, Bank 3, Sensor 1 Oxygen Sensor, Bank 3, Sensor 2 Oxygen Sensor, Bank 4, Sensor 1 Oxygen Sensor, Bank 4, Sensor 2
64
OBD2

Tool Display OBD Support OBD Support OBD Support OBD Support OBD Support OBD Support OBD Support OBD Support OBD Support
Unit -
OBD Support OBD Support OBD Support OBD Support
PTO Status Rel TPS Spark Adv STFT B1 STFT B1 S1 STFT B1 S2 STFT B1 S3 STFT B1 S4 STFT B2 STFT B2 S1 STFT B2 S2 STFT B2 S3 STFT B2 S4 STFT B3 STFT B4 Time DTC Clr Time Since Start TPS TPS B TPS C
% deg % % % % % % % % % % % % hrs, min sec % % %
Value OBD2 OBD OBD and OBD2 OBD1 No OBD EOBD EOBD and OBD2 EOBD and OBD EOBD, OBD and OBD2 JOBD JOBD and OBD2 JOBD and EOBD JOBD, EOBD and OBD2 On / Off XXX.X XX XXX.X XXX.X XXX.X XXX.X XXX.X XXX.X XXX.X XXX.X XXX.X XXX.X XXX.X XXX.X XXXX, XX XXXX XXX.X XXX.X XXX.X
PID Description OBD Requirements OBD Requirements OBD Requirements OBD Requirements OBD Requirements OBD Requirements OBD Requirements OBD Requirements OBD Requirements
OBD Requirements OBD Requirements OBD Requirements OBD Requirements
Power Take Off Status Relative Throttle Position Ignition Timing Advance #1 Cylinder Short Term Fuel Trim-Bank 1 Bank 1 - Sensor 1 Bank 1 - Sensor 2 Bank 1 - Sensor 3 Bank 1 - Sensor 4 Short Term Fuel Trim-Bank 2 Bank 2 - Sensor 1 Bank 2 - Sensor 2 Bank 2 - Sensor 3 Bank 2 - Sensor 4 Short Term Fuel Trim-Bank 3 Short Term Fuel Trim-Bank 4 Time since DTC Cleared Time Since Engine Start Absolute Throttle Position Absolute Throttle Position B Absolute Throttle Position C
OBD2
65

Tool Display Veh Speed
Warm-up DTC Clr
Unit km/h / mph -
Value XXX / XXX
PID Description Vehicle Speed Sensor
XXX
# Warm-ups since DTC Cleared
66
OBD2
Glossary
GLOSSARY OF TERMS AND ABBREVIATIONS
INTRODUCTION
This Glossary contains definitions for abbreviations and terms you may find in this manual or in your vehicle service manual.

CARB California Air Resources Board CCM Central Control Module Computer Control System An electronic control system, consisting of an on-board computer and related sensors, switches and actuators, used to ensure peak performance and fuel efficiency while reducing pollutants in the vehicles emissions. DIY Do-It-Yourself DLC Data Link Connector Drive Cycle An extended set of driving procedures that takes into consideration the various types of driving conditions encountered in real life. Driving Condition A specific environmental or operation condition under which a vehicle is operated; such as starting the vehicle when cold, driving at steady speed (cruising), accelerating, etc. DTC(s) Diagnostic Trouble Code(s) EGR Exhaust Gas Recirculation EPA Environmental Protection Agency EVAP Evaporative Emissions System Fault Code See DTCs Freeze Frame A digital representation of engine and/or emissions system conditions present when a fault code was recorded. FTP Fuel Tank Pressure Generic Code A DTC that applies to all OBD2 compliant vehicles. I/M Test / Emissions Test / Smog Check A functional test of a vehicle to determine if tailpipe emissions are within Federal/State/Local requirements. LCD Liquid Crystal Display LED Light Emitting Diode LTFT Long Term Fuel Trim, is a program in the vehicles computer designed to add or subtract fuel from the vehicle to compensate for operating conditions that vary from the ideal A/F ratio (long term).
OBD2
67
Glossary
Manufacturer Specific Code A DTC that applies only to OBD2 compliant vehicles made by a specific manufacturer. MIL Malfunction Indicator Lamp (also referred to as Check Engine light OBD1 On-Board Diagnostics Version 1 (also referred to as OBD I) OBD2 On-Board Diagnostics Version 2 (also referred to as OBD II) On-Board Computer The central processing unit in the vehicles computer control system. PCM Powertrain Control Module Pending Code A code recorded on the first trip for a two-trip code. If the fault that caused the code to be set is not detected on the second trip, the code is automatically erased. STFT Short Term Fuel Trim, is a program in the vehicles computer designed to add or subtract fuel from the vehicle to compensate for operating conditions that vary from the ideal A/F ratio. The vehicle uses this program to make minor fuel adjustments (fine tune) on a short-term basis. System Status An indication of whether or not a vehicles emissionsrelated system are operating properly and are ready for Inspection and Maintenance testing. Trip Drive Cycle Vehicle operation that provides the necessary driving condition to enable a vehicle Monitor to run and complete its diagnostic testing. VECI Vehicle Emission Control Information Decal
68
OBD2
Warranty and Servicing

LIMITED ONE YEAR WARRANTY
The Manufacturer warrants to the original purchaser that this unit is free of defects in materials and workmanship under normal use and maintenance for a period of one (1) year from the date of original purchase. If the unit fails within the one (1) year period, it will be repaired or replaced, at the Manufacturers option, at no charge, when returned prepaid to the Service Center with Proof of Purchase. The sales receipt may be used for this purpose. Installation labor is not covered under this warranty. All replacement parts, whether new or remanufactured, assume as their warranty period only the remaining time of this warranty. This warranty does not apply to damage caused by improper use, accident, abuse, improper voltage, service, fire, flood, lightning, or other acts of God, or if the product was altered or repaired by anyone other than the Manufacturers Service Center. The Manufacturer, under no circumstances shall be liable for any consequential damages for breach of any written warranty of this unit. This warranty gives you specific legal rights, and you may also have rights, which vary from state to state. This manual is copyrighted with all rights reserved. No portion of this document may be copied or reproduced by any means without the express written permission of the Manufacturer. THIS WARRANTY IS NOT TRANSFERABLE. For service, send via U.P.S. (if possible) prepaid to Manufacturer. Allow 3-4 weeks for service/repair.
SERVICE PROCEDURES
If you have any questions, require technical support or information on UPDATES and OPTIONAL ACCESSORIES, please contact your local store, distributor or the Service Center. USA & Canada: (800) 544-4124 (6:00 AM-6:00 PM, Monday-Saturday PST) All others: (714) 241-6802 (6:00 AM-6:00 PM, Monday-Saturday PST) FAX: (714) 432-7511 (24 hr.) Web: www.innova.com
OBD2
69
Innova Electronics Corp.
17352 Von Karman Avenue Irvine, CA 92614
Instruction MRP #93-0328 Rev. A Copyright 2011 IEC. All Rights Reserved.
2011

Manual Obd

Uploaded by

Copyright:

Available Formats

Manual Obd

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Obd

Uploaded by

Copyright:

Available Formats

Table of Contents

You Can Do It!

About the Diagnostic Tool

STANDARD CATEGORY TLEV TLEV INTERMEDIATE

Data Link Connector (DLC) Location

LEFT CORNER OF DASH

NEAR CENTER OF DASH

About the Diagnostic Tool

Adjustments After Battery Installation

Diagnostic Tool Controls

CONTROLS AND INDICATORS

Diagnostic Tool Controls

Diagnostic Tool Controls

Diagnostic Tool Controls

COMPUTER ENGINE CONTROLS

The Basic Engine Computer Control System

TYPICAL COMPUTER CONTROL SYSTEM

INPUT DEVICES Oxygen Sensors

On-Board Diagnostics - First Generation (OBD1)

On-Board Diagnostics - Second Generation (OBD2)

DIAGNOSTIC TROUBLE CODES (DTCs)

OBD2 DTC EXAMPLE

DTCs and MIL Status

OBD2 Reference Table

3 trips 3 trips 3 trips 3 trips 3 trips 3 trips 3 trips

Preparation for Testing

PRELIMINARY VEHICLE DIAGNOSTIC WORKSHEET

Preparation for Testing

LIST ANY REPAIRS DONE IN THE PAST SIX MONTHS:

PROBLEMS STARTING No symptoms Will not crank

Preparation for Testing

WEATHER CONDITIONS WHEN PROBLEM OCCURS

CHECK ENGINE LIGHT / DASH WARNING LIGHT Never ON

Preparation for Testing

BEFORE YOU BEGIN

Preparation for Testing

VEHICLE SERVICE MANUALS

Using the Diagnostic Tool

CODE RETRIEVAL PROCEDURE

Using the Diagnostic Tool

Using the Diagnostic Tool

Using the Diagnostic Tool

Using the Diagnostic Tool

Using the Diagnostic Tool

Using the Diagnostic Tool

VIEWING ENHANCED DTCs

Chrysler/Jeep Enhanced DTCs

Using the Diagnostic Tool

Using the Diagnostic Tool

Ford/Mazda Enhanced DTCs

Using the Diagnostic Tool

Using the Diagnostic Tool

General Motors/Isuzu Enhanced DTCs

Using the Diagnostic Tool

Honda/Acura Enhanced DTCs

Using the Diagnostic Tool

2. To read the display:

Using the Diagnostic Tool

Toyota/Lexus Enhanced DTCs

Using the Diagnostic Tool