Scribd
Upload
116 views2 pages

Eot Spec - Bhel

The document provides details of specifications required for a crane to be supplied with a tender. It includes specifications for the total weight of the crane and its components, details of the hoist, trolley, bridge, control systems, and additional specifications like approach distances, clearances, deflections, wiring, motors, brakes, remote control, and weighing systems. Deviations from the specifications, if any, and the supply/installation timeline must also be provided.

Uploaded by

Paulkumar Ramaiah
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
116 views2 pages

Eot Spec - Bhel

The document provides details of specifications required for a crane to be supplied with a tender. It includes specifications for the total weight of the crane and its components, details of the hoist, trolley, bridge, control systems, and additional specifications like approach distances, clearances, deflections, wiring, motors, brakes, remote control, and weighing systems. Deviations from the specifications, if any, and the supply/installation timeline must also be provided.

Uploaded by

Paulkumar Ramaiah
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ANNEXURE-B TO SPECIFICATION FT/SP/47A DETAILS OF CRANE TO BE FURNISHED WITH THE TENDER.

SN 1 2 3 4 Description Specification of the crane offered Deviations, if any Time Supply / E & C Total weight of crane in MT 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9

Page 1 of 2

Details to be filled

Total wt. of crane (MT) Wt. of Trolley/Crab (MT) Wt of each girder (MT) Wt. of each end carriage (MT) Wt. of cabin (MT) Wt. of electricals Wt. of platforms Wt. of LT drive Wt. of other components (specify the component name) Note: Total wt. of crane should match the other break-up weights. 4.10 LT Wheel load (max / min) 5 Hoist: (Main & Auxiliary) Speed in M/min With maximum working load With empty hook Rope size and construction details No. of rope falls supporting the load Dia of Drum Material of Drum Material of Sheaves Lift of hook above floor level (exclusive of travel required to operate limit switch) Drop of hook below floor level 6 Trolley Speed M/min with maximum load Wheel span Material & Diameter of wheels Size of trolley runway rails 7 Bridge Speed M/min with maximum working load Wheel base Material & Diameter of wheels Make,Type & Size of Bearings for gears Number of wheels on each end of crane Maximum wheel load & spacing Clear width of foot walk

ANNEXURE-B TO SPECIFICATION FT/SP/47A 9 Make of Control, 10 Hook approach (MH) Cab end Opposite cab end Distance between Main & Auxiliary hook 11 Distance centerline between girders to extreme outside of crane Cab side Opposite cab side 12 Distance bottom of cabin to floor Clearances Bridge truck & building column Trolley & roof chord 13 Maximum deflection of girders under maximum working load 14 Wiring trade name and classification of wire insulation 15 Make, HP & NO of Motors MH AH CT LT 16 Make, Type & NO of Brakes MH AH CT LT 17 Make, Type & NO of Lt Switch MH AH CT LT 18 Material of Gears & Pinion, Type 19 Material of Gear Boxes 20 Radio Remote Control: Make, Type, Range, Provision for Siren, Lights etc 21 Crane weighing system: Make, Capacity, No. of load cells, Location etc

Page 2 of 2

NOTE: If above clauses are found inadequate for furnishing all necessary information of the crane offered, the supplier may append further information separately. Other information as per Appendix B of IS4137 and Annexure A of IS3177 may also be submitted, if asked for during technical discussion.

You might also like