INSTRUCTION MANUAL

VHF MARINE TRANSCEIVER

iM88

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SAFETY TRAINING INFORMATION

Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the TX indicator lights red. You can cause the radio to transmit by pressing the PTT switch. ALWAYS use Icom authorized accessories (antennas, batteries, belt clips, etc.). Use of unauthorized accessories can cause the FCC RF exposure compliance requirements to be exceeded. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clips which are listed on page 31 when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this radio.

W ARN ING

This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specically authorized by the manufacturer for use with this radio.

Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.

C AU TIO N

IN CASE OF EMERGENCY
If your vessel requires assistance, contact other vessels and the Coast Guard by sending a distress call on Channel 16.

RECOMMENDATION
CLEAN THE TRANSCEIVER THOROUGHLY WITH FRESH WATER after exposure to saltwater. Otherwise, the transceivers keys, switches and controllers may become inoperable due to salt crystallization.

USING CHANNEL 16 DISTRESS CALL PROCEDURE

1. MAYDAY MAYDAY MAYDAY. 2. THIS IS ........................... (name of vessel) 3. Your call sign or other indication of the vessel. 4. LOCATED AT ..................... (your position) 5. The nature of the distress and assistance required. 6. Any other information which might facilitate the rescue.

ii

FOREWORD
Thank you for purchasing this Icom product. The IC-M88 VHF MARINE TRANSCEIVER is designed and built with Icoms state of the art technology and craftsmanship. With proper care this product should provide you with years of trouble-free operation.

FEATURES
 22 free channels for land use
The IC-M88 has 22 free channels reserved for Land use (146174MHz). Wide/narrow channel spacing is programmable for each channel, and CTCSS and DTCS signaling is included.
*Appropriate license may be required.

IMPORTANT
READ ALL INSTRUCTIONS
pletely before using the transceiver. carefully and com-

 Tough waterproof construction

The IC-M88 is built tough to withstand hazardous and unhospitable environments at sea and on land. Even if the IC-M88 is dropped into water, its waterproong* will protect it from harm. The compact and durable body meets the military specications (MIL-STD).
* Equivalent to JIS waterproof grade 7. (1m depth for 30 minutes)

SAVE THIS INSTRUCTION MANUALThis instruction manual contains important operating instructions for the IC-M88.

 Simple operation
6 clearly labelled buttons on the front panel and the volume/power knob maximize simplicity of operation. Even when wearing gloves, the large buttons are easy to operate. A large, clear LCD with backlighting and backlit buttons make night time operation simple.

EXPLICIT DEFINITIONS
DEFINITION Personal injury, re hazard or electric shock RWARNING may occur. CAUTION NOTE iii Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, re or electric shock. WORD

 Intrinsically safe (I/S) version available

PRECAUTION
RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a re hazard or result in an electric shock. RWARNING! NEVER hold the transceiver so that the
antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical.

BE CAREFUL! The IC-M88 employs waterproof construction, which corresponds to JIS waterproof specication, Grade 7 (1 m; 3 ft depth for 30 min.). However, once the transceiver has been dropped, waterproong cannot be guaranteed due to the fact that the transceiver may be cracked, or the waterproof seal damaged, etc. MAKE SURE
the exible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver.

NEVER

connect the transceiver to a power source other than the BP-226 or BP-227. Such a connection will ruin the transceiver. in areas with temperatures below 20C (4F) or above +60C (+140F): Marine, below 30C (22F) or above +60C (+140F): LMR.

AVOID using or placing the transceiver in direct sunlight or

For U.S.A. only Changes or modications to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations.

CAUTION:

KEEP the transceiver out of the reach of children. KEEP the transceiver at least 0.9 meters (3.0 ft) away from
your vessels magnetic navigation compass.
Icom, Icom Inc. and are registered trademarks of Icom Incorporated (Japan) in the United States, United Kingdom, Germany, France, Spain, Russia and/or other countries.

iv

TABLE OF CONTENTS
SAFETY TRAINING INFORMATION ................................... i IN CASE OF EMERGENCY ............................................... ii RECOMMENDATION .......................................................... ii FOREWORD ...................................................................... iii IMPORTANT ....................................................................... iii EXPLICIT DEFINITIONS .................................................... iii FEATURES ......................................................................... iii PRECAUTION .................................................................... iv TABLE OF CONTENTS ...................................................... v 1 OPERATING RULES ...................................................... 1 2 SUPPLIED ACCESSORIES AND ATTACHMENTS.... 23 3 PANEL DESCRIPTION ............................................... 47 I Front, top and side panels............................................ 4 I Function display .......................................................... 6 4 BASIC OPERATION ................................................. 812 I Channel selection ........................................................ 8 I Receiving and transmitting ........................................ 10 I Adjusting the squelch level ........................................ 11 I Automatic backlighting ............................................... 11 I Voice scrambler operation ......................................... 11 I Call channel programming ........................................ 12 I Lock function ............................................................. 12 5 SCAN OPERATION ................................................ 1314 I Scan types ................................................................. 13 I Setting tag channels .................................................. 14 I Starting a scan .......................................................... 14 6 DUALWATCH/TRI-WATCH .......................................... 15 I Description ................................................................ 15 I Operation ................................................................... 15 7 LAND CHANNEL OPERATION ................................... 16 I LAND Channel Group ............................................... 16 I Function display ......................................................... 16 8 SET MODE ............................................................. 1721 I SET mode programming ........................................... 17 I SET mode items ........................................................ 18 9 BATTERY CHARGING ........................................... 2226 I Battery charging ........................................................ 22 I Battery cautions ......................................................... 22 I Optional BP-226 battery case ................................... 24 I AD-100 installation .................................................... 25 I Optional battery chargers .......................................... 26 10 SPEAKER-MICROPHONE .......................................... 27 I HM-138 Description ................................................... 27 I Attachments .............................................................. 27 11 TROUBLESHOOTING ................................................. 28 12 VHF MARINE CHANNEL LIST ................................... 29 13 SPECIFICATIONS .........................................................30 14 QUICK REFERENCE ....................................................31 15 OPTIONS.......................................................................33

OPERATING RULES
D Priorities
Read all rules and regulations pertaining to priorities and keep an up-to-date copy handy. Safety and distress calls take priority over all others. You must monitor Channel 16 when you are not operating on another channel. False or fraudulent distress calls are prohibited under law.

(2) OPERATORS LICENSE A restricted Radiotelephone Operator Permit is the license most often held by small vessel radio operators when a radio is not required for safety purposes. The Restricted Radiotelephone Operator Permit must be posted near the transceiver or be kept with the operator. Only a licensed radio operator may operate a transceiver. However, non-licensed individuals may talk over a transceiver if a licensed operator starts, supervises, ends the call and makes the necessary log entries. A current copy of the applicable government rules and regulations is only required to be on hand for vessels in which a radio telephone is compulsory. However, even if you are not required to have these on hand it is your responsibility to be thoroughly acquainted with all pertinent rules and regulations.

D Privacy
Information overheard but not intended for you cannot lawfully be used in any way. Indecent or profane language is prohibited.

D Radio licenses
(1) SHIP STATION LICENSE When your craft is equipped with a VHF FM transceiver, you must have a current radio station license before using the transceiver. It is unlawful to operate a ship station which is not licensed. Inquire through your dealer or the appropriate government agency for a Ship-Radiotelephone license. This license includes the call sign which is your crafts identication for radio purposes.

NOTE: Even though the IC-M88 is capable of operation on VHF marine channels 3, 21, 23, 61, 64, 81, 82 and 83, according to FCC regulations these simplex channels cannot be lawfully used by the general public in USA waters. 1

SUPPLIED ACCESSORIES AND ATTACHMENTS

w Clip the belt clip to a part of your belt and insert the stopper to the belt clip.

D Supplied accessories The following accessories are supplied: Qty. Swivel belt clip . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Stopper for the swivel belt clip . . . . . . . . . . . . . . . .1 Screws for the swivel belt clip . . . . . . . . . . . . . . . .2 Flexible antenna . . . . . . . . . . . . . . . . . . . . . . . . . .1 Handstrap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Battery pack (BP-227) . . . . . . . . . . . . . . . . . . . . . .1 AC adapter (BC-147A/E)* . . . . . . . . . . . . . . . . . . .1 Battery charger (BC-152) . . . . . . . . . . . . . . . . . . .1
*Depending on version

D Swivel belt clip To attach: q Attach the stopper to the back of the transceiver. Supplied screws Stopper

e Once the transceiver is locked in place, it will swivel 360 degrees.

SUPPLIED ACCESSORIES AND ATTACHMENTS

To remove: Turn the transceiver upside down, and then lift up to release the transceiver from the belt clip.

D Flexible antenna Connect the supplied exible antenna to the antenna connector. CAUTION: Transmitting without an antenna may damage the transceiver. NEVER HOLD by the antenna when carrying the transceiver.

D Handstrap Slide the handstrap through the loop on the side of the transceiver as illustrated at right. Facilitates carrying.

R CAUTION!
HOLD THE TRANSCEIVER TIGHTLY, WHEN ATTACHING OR REMOVING THE TRANSCEIVER FROM THE BELT CLIP. If the transceiver is accidentally dropped and the swivel belt clips stopper is scratched or damaged, the swivel belt clip may not work properly. 3

PANEL DESCRIPTION
q VOLUME CONTROL [VOL] Turns power ON and adjusts the audio level. w ANTENNA CONNECTOR (p. 3) Connects the supplied antenna. e SPEAKER-MICROPHONE CONNECTOR [SP MIC] (p.27) Connects the optional speaker-microphone. w
[SP MIC] jack cover NOTE: KEEP the [SP MIC] jack cover attached to the transceiver when the speaker-microphone is not in use.

I Front, top and side panels

q

!0 o

r SCAN [SCNDUAL] (pgs. 14, 15) Starts and stops normal or priority scan. Enters Watch mode when pushed for 1 sec. t TRANSMIT POWER/LOCK SWITCH [H/LLOCK] Selects high, middle or low power when pushed. (p. 10) Toggles the lock function ON/OFF when pushed for 1 sec. (p. 12) y CHANNEL 16 SWITCH [169] Selects Channel 16 when pushed. (p. 8) Selects the call channel when pushed for 1 sec. (p. 8) Enters call channel write mode when the call channel is selected and this switch is pushed for 3 sec. (p. 12)

i r u t y

PANEL DESCRIPTION
u CHANNEL UP/DOWN SWITCHES [Y]/[Z] Select an operating channel. (p. 9) Selects the SET mode condition of item. (p. 17) Checks tag channels or changes scanning direction during scan. (p. 14) Sets and clears the displayed channel as a tag (scanned) channel when pushed both switches for 1 sec. While turning power ON, clears all tag channels in the selected channel group when both switches are pushed. i CHANNEL/WEATHER CHANNEL SWITCH [CH/WXU/I/C/L] Selects and toggles the regular channels and weather channel when pushed. (pgs. 8, 9, 16) Selects one of 4 regular channels in sequence when pushed for 1 sec. (pgs. 9, 16) - U.S.A., International, Canadian and Land channels are available. Push to return to the condition before selecting the channel when the priority channel or the call channel is selected. o SQUELCH SWITCH [SQL] (p. 11) Push this switch, then set the squelch level with [Y]/[Z]. Manually opens the squelch for channel monitoring while pushed and held. While pushing this switch, turn the power ON to enter the set mode. !0 PTT SWITCH [PTT] Push and hold to transmit; release to receive.

BATTERY PACK RELEASE BUTTON To release the battery pack: Push the battery release button in the direction of the arrow (q) as shown below. The battery pack is then released. To attach the battery pack: Slide the battery pack on the back of the transceiver in the direction of the arrow (w), then lock it with the battery release button. *Slide the battery pack until the battery release button makes a click sound. Battery pack w

q Battery release button

CAUTION!: When pushing the battery release button, slide the battery pack slightly in the direction of the arrow (w) to ease release. This will prevent possible injuring to your ngers or nails 5

PANEL DESCRIPTION
q TRANSMIT INDICATOR (p. 10) Appears while transmitting. w BUSY INDICATOR (p. 10) Appears when receiving a signal or when the squelch opens. blinks while monitoring. q w e r t y u e TAG CHANNEL INDICATOR (p. 14) Appears when a tag channel is selected. i o !0 !1 !2 r SCAN INDICATOR (p. 14) Blinks while scanning. t LOCK INDICATOR (p. 12) Appears while the lock function is activated. y NARROW INDICATOR (p. 16) Appears when narrow channel spacing is selected. (LAND channel group only) u BATTERY INDICATOR Indicates remaining battery power. Indication Battery level Full Middle Charging Discharged required

I Function display

!7 !6 !5

!4

!3

PANEL DESCRIPTION
i WEATHER CHANNEL/WEATHER ALERT INDICATORS WX appears when the weather channel group is selected. (p. 9) ALT appears while the weather alert function is activated. o BELL INDICATOR Blinks when an alert tone is received. !0 DUALWATCH/TRI-WATCH INDICATORS (p. 15) DUAL appears during dualwatch; TRI appears during tri-watch. !1 SCRAMBLER INDICATOR (Available for I/S version only) Appears when the optional voice scrambler is activated. (pgs. 11, 21) !2 DUPLEX INDICATOR Appears when a duplex channel is selected. !3 SUB CHANNEL READOUT Indicates Channel 16 during priority scan, dualwatch or tri-watch. (p. 15). Indicates the SET mode item while in SET mode. !4 CHANNEL NUMBER READOUT Indicates the selected operating channel number. In SET mode, indicates the selected condition. !5 CALL CHANNEL INDICATOR (p. 8) Appears when the call channel is selected.

!6 CHANNEL GROUP INDICATOR (pgs. 9, 16) U appears when U.S.A.; I appears when International; C appears when Canadian; appears when LAND channel group is selected. !7 TRANSMIT POWER INDICATOR (p. 10) LOW appears when low power is selected. MID appears when middle power is selected. No indication when high power is selected.

BASIC OPERATION
D Channel 9 (Call channel)
Channel 9 is the leisure-use call channel. Each regular channel group has separate call channels. In addition, each call channel is monitored during tri-watch. The call channels can be reprogrammed (p. 12) and are used to store your most often used channels in each channel group for quick recall. q Push [169] for 1 sec. to select the call channel in the selected channel group.
CALL and the call channel number appear. Each channel group may have its own call channel after programming a call channel. See the Call channel programming on p. 12 for details. w Push [CH/WXU/I/C/L] to return to the condition before selecting Channel 9 (call channel), or push [Y]/[Z] to select

I Channel selection
D Channel 16
Channel 16 (Distress channel) is used for establishing initial contact with another station and for emergency communications. Channel 16 is automatically monitored during both dualwatch and tri-watch. While standing by, you must monitor Channel 16. q Push [169] to select Channel 16. w Push [CH/WXU/I/C/L] to return to the condition before selecting Channel 16, or push [Y]/[Z] to select the operating channel.
9

Push

the operating channel.

9

Push for 1 sec.

BASIC OPERATION D U.S.A., International and Canadian channels

There are 57 U.S.A., 57 International, and 61 Canadian channels. These channel groups may be specied for the operating area. q Push [CH/WXU/I/C/L] to select a regular channel.
If a weather channel appears, push [CH/WXU/I/C/L] again.

D Weather channels (Available for USA version only) There are 10 weather channels. They are used for monitoring weather channels from the NOAA (National Oceanographic and Atmospheric Administration) broadcasts.
q Push [CH/WXU/I/C/L] to select the weather channel group. w Push [Y]/[Z] to select a weather channel. e Push [CH/WXU/I/C/L] to return to the condition before selecting the weather channel group.
U/I/C/L

w Push [Y]/[Z] to select a channel.

DUP appears for duplex channels.

e To change the channel group, push [CH/WXU/I/C/L] for 1 sec.

U.S.A., International and Canadian channels can be selected in sequence. Depending on the setting, LAND channel can be selected. See the LAND CHANNEL OPERATION on p. 16 for details.

Push

Push for 1 sec.

U/I/C/L U/I/C/L

For your convenience: The IC-M88 can detect a weather alert tone on the selected weather channel while receiving in another channel or during scanning. See the SET mode items on p. 18 for details. U.S.A. channels

U/I/C/L

International channels

Canadian channels

BASIC OPERATION
IMPORTANT: To maximize the readability of your transmitted signal, pause a few sec. after pushing [PTT], hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth and speak at a normal voice level. NOTE: The transceiver has a power save function to conserve the battery power and it cannot be turned OFF. The power save function activates automatically when no signal is received for 5 sec. For U.S.A version: To prevent accidental prolonged transmission, etc., the IC-M88 has a time-out timer function. This timer cuts a transmission OFF after 5 min. of continuous transmission. y Push and hold to transmit u Release to receive w Opening the squelch q Power ON e Set volume

I Receiving and transmitting

CAUTION: Transmitting without an antenna may
damage the transceiver.
q Rotate [VOL] clockwise to turn power ON. w Use the squelch function to mute any audio noise if necessary. After pushing the [SQL] for 1 sec., the squelch function is cut off until [SQL] is released. (default) e Push [SQL] for 1 sec. (see the SET mode on p. 19), and rotate volume to set the audio output level. r Push [Y]/[Z] to select the desired channel.
- When receiving a signal, appears and audio is emitted from the speaker. - Further adjustment of [VOL] may be necessary at this point. t Push [H/LLOCK] to select the output power if necessary. - LOW appears when low power is selected; MID appears when middle power is selected; no indication when high power is selected. - Choose low power to conserve battery power, choose high power for longer distance communications. - Some channels are for low power only.

y Push and hold [PTT] to transmit, then speak into the microphone. - TX appears.
- Channel 70 cannot be used for transmission (for GMDSS use).

u Release [PTT] to receive. r Set channel t Set output power

10

BASIC OPERATION

I Adjusting the squelch level

The IC-M88 has a squelch even though there is no control knob for it. In order to receive signals properly, as well as for the scan to function effectively, the squelch must be adjusted to the proper level. q Push [SQL], then adjust the squelch level with [Y]/[Z].
- SL indicator appears. - There are 11 squelch levels to choose from: OP is completely open; 10 is the tight squelch level. - When no key is pushed for 5 sec., the transceiver returns to normal condition.

I Voice scrambler operation

(Available for I/S version only)

D Activating the scrambler

The optional voice scrambler provides private communications. In order to receive or send scrambled transmissions, you must rst activate the scrambler function. q Select an operating channel except Channel 16, 70 or weather channels. w While pushing and holding [SQL], push [SCNDUAL].
SCRM appears.

w Push [SQL] again to return to normal condition.

e To turn the scrambler function OFF, repeat step w.

SCRM disappears.

Appears when the voice scrambler function is in use.

D Programming scramble codes

I Automatic backlighting
This function is convenient for nighttime operation. The automatic backlighting can be activated in SET mode. (p. 19) Push any key except for [PTT] to turn the backlighting ON.
The backlighting is automatically turned OFF after 5 sec. of inactivity.

There are 32 codes (1 to 32) available for programming. Set the code in SET mode. In order to understand each other, all transceivers in your group must have the same scramble code, as well as the same scrambler unit. See page 21 for scrambler code setting details.

11

BASIC OPERATION

I Call channel programming

The call channel key is used to select Channel 9 by default, however, you can program your most often-used channels in each channel group for quick recall. q Push [CH/WXU/I/C/L] for 1 sec. several times to select the desired channel group (USA, INT, CAN) to be programmed. w Push [169] for 1 sec. to select the call channel.
CALL and call channel number appear.

t Push [169] to program the displayed channel as the call channel.

The call channel number stop ashing.

I Lock function
This function electronically locks all keys (except for [PTT], [SQL] and [H/LLOCK]) to prevent accidental channel changes and function access. Push [H/LLOCK] for 1 sec. to turn the lock function ON and OFF.

e Push [169] again for 3 sec. (until a long beep changes to 2 short beeps) to enter call channel programming condition.
Call channel number to be programmed ashes.

Appears while the lock function is used.

r Push [Y]/[Z] to select the desired channel.

12

SCAN OPERATION
I Scan types
Scanning is an efcient way to locate signals quickly over a wide frequency range. The transceiver has priority scan and normal scan. In addition, the weather alert and auto scan function is available for standby convenience. These functions can be activated simultaneously, depending on the settings in SET mode. (pgs. 18, 19) PRIORITY SCAN
CH 01 CH 02

Set the tag channels (scanned channel) before scanning. Clear the tag channels which inconveniently stop scanning, such as digital communications. Choose priority or normal scan in SET mode. (p. 18)

NORMAL SCAN
CH 01 CH 02

WX*

CH 16

CH 03

WX*

CH 03

CH 05

CH 04

CH 05

CH 04

* Previously selected weather channel when weather alert function is ON Priority scan searches through all tag channels in sequence while monitoring Channel 16. When a signal is detected on Channel 16, scan pauses until the signal disappears; when a signal is detected on a channel other than Channel 16, scan becomes dualwatch until the signal disappears.

* Previously selected weather channel when weather alert function is ON. Normal scan, like priority scan, searches through all tag channels in sequence. However, unlike priority scan, Channel 16 is not checked unless Channel 16 is set as a tag channel. 13

SCAN OPERATION

I Setting tag channels

For more efficient scanning, add desired channels as tag channels or clear tag channels for unwanted channels. Nontag channels will be skipped during scanning. Tag channels can be assigned to each channel group (USA, INT, CAN) independently. q Select the desired channel group (USA, INT, CAN) by pushing [CH/WXU/I/C/L] for 1 sec., if desired. w Select the desired channel to set as a tag channel. e Push both [Y] and [Z] for 1 sec. to set the displayed channel as a tag channel.
TAG appears in the function display.

I Starting a scan
Set the weather alert function, priority scan function, scan resume timer and auto scan function in advance, using SET mode. (pgs. 18, 19) q Select the desired channel group (USA, CAN, INT) by pushing [CH/WXU/I/C/L] for 1 sec., if desired.
When the weather alert function is in use, select the desired weather channel with [CH/WXU/I/C/L] and [Y]/[Z]. w Push [SCNDUAL] to start priority or normal scan. SCAN blinks in the function display. 16 appears during priority scan. When a signal is received, scan pauses until the signal disappears or resumes after pausing 5 sec. according to SET mode setting. (Channel 16 is still monitored during priority scan.) Push [Y]/[Z] to check the scanning tag channels, to change the scanning direction or resume the scan manually. e To stop the scan, push [SCNDUAL]. SCAN disappears. Pushing [PTT], [169] or [CH/WXU/I/C/L] also stops the scan.

r To cancel the tag channel setting, push both [Y] and [Z] for 1 sec.
TAG disappears.

Clearing all tag channels in the selected channel group While pushing and holding both [Y] and [Z], turn power ON to clear all tag channels in the channel group.

[Example]: Starting a normal scan. Push

DUAL

Scan starts.

Scan pauses when receiving a signal and audio is emitted.

Push
DUAL

to stop the scan.

14

DUALWATCH/TRI-WATCH
I Description
Dualwatch monitors Channel 16 while you are receiving another channel; tri-watch monitors Channel 16 and the call channel while receiving another channel. DUALWATCH/TRI-WATCH SIMULATION Call channel

I Operation
q Select the desired operating channel. w Push [SCNDUAL] to start dualwatch or tri-watch (depending on SET mode setting).
DUAL blinks during dualwatch; TRI blinks during tri-watch. A beep tone sounds when a signal is received on Channel 16. Tri-watch becomes dualwatch when receiving a signal on the call channel. e To cancel dualwatch/tri-watch, push [SCNDUAL] again.

[Example]: Operating tri-watch on INT channel 07.

Push for 1 sec.
DUAL

Tri-watch starts.

Dualwatch

Tri-watch
Signal is received on call channel.

If a signal is received on Channel 16, dualwatch/tri-watch pauses on Channel 16 until the signal disappears. If a signal is received on the call channel during tri-watch, triwatch becomes dualwatch until the signal disappears. To transmit on the selected channel during dualwatch/tri-watch, push and hold [PTT]. If no signal is received, the transceiver enters the power saving condition for 0.5 sec. after checking the operating channel every cycle.

Signal received on Channel 16 takes priority. Tri-watch resumes after the signal disappears.

15

LAND CHANNEL OPERATION

I Function display
When Narrow, DTCS or CTCSS is set, the display shows the indications as below. Appears when Narrow channel spacing is set.

I LAND Channel Group

A max. of 22 free LAND mobile channels (allocated 146.000 to 174.000 MHz) can be programmed into the LAND channel group for simple communication with LMR transceivers in the VHF band. Moreover, any of the marine channels in the USA, INT and CAN channel groups can be programmed. The default setting of the LAND channel group is the same as that of the INT channel group. Ask your local Icom dealer for the LAND channel group setting and LMR frequency programming details. q Push [CH/WXU/I/C/L] to select a regular channel.
If a weather channel appears, push [CH/WXU/I/C/L] again.

w To change the channel group, push [CH/WXU/I/C/L] for 1 sec several times.
appears when LAND channel group is selected.

Appears when DTCS is set.

e Push [Y]/[Z] to select a channel.

DUP appears for duplex channels.
U/I/C/L

Appears when CTCSS set.

Push

NOTE: The basic settings (e.g. call channel programming) are same as the U.S.A., International and Canadian channels. Refer to the appropriate pages for details. 16

SET MODE
I SET mode programming
SET mode is used to change the condition of 13 transceiver functions: beep tone function, weather alert function, priority scan function, scan resume timer, auto scan function, dual/triwatch function, monitor switch action, automatic backlighting, LCD contrast selection, auto power save function, self check function, battery voltage indicator and scrambler code*.

D SET mode operation

q Turn power OFF. w While pushing [SQL], turn power ON to enter SET mode. bp appears. e Push [SQL] to select the desired item, if necessary. r Push [Y]/[Z] to select the desired condition of the item. t To exit SET mode, push [169].

SET MODE CONTENTS The displays show the default settings, and the item initial is displayed in the dotted circle.

Starting item

Push [SQL]

* Available for the I/S version only

17

SET MODE D Priority scan function Pr

The transceiver has 2 scan typesnormal and priority scans. Normal scan searches all tag channels in the selected channel group. Priority scan searches all tag channels in sequence while monitoring Channel 16.
PUSH

I SET mode items

D Beep tone function bP
You can select silent operation by turning the beep tones OFF, or you can have 2 types of conrmation beeps sound at the push of a switch. When ON is selected, a xed beep (Pi) sounds and when US is selected, the preset beeps (e.g. do, re, mi) sound.

PUSH

Normal scan (default) User Beep

Priority scan

Beep tone ON (default)

D Scan resume timer St

The scan resume timer can be set as a pause (OFF) or timer scan (ON). When OFF is selected, the scan pauses until a received signal disappears. When ON is selected, the scan pauses for 5 sec. after receiving a signal and then resumes even if the signal has been received.

D Weather alert function AL

An NOAA broadcast station transmits a weather alert tone before any important weather announcements. When the weather alert function is turned ON, the transceiver detects the alert, the bell indicator blinks and sounds a beep tone until the transceiver is operated. The previously selected (used) weather channel is checked any time during standby, or while scanning, when the power save function is activated.
ALT appears when the function is set ON.

PUSH

Scan resume timer OFF (default)

Scan resume timer ON

PUSH

Weather alert function OFF (default) 18

Weather alert function ON

SET MODE D Auto scan function AS

The Auto scan function starts the desired scan automatically when no signal is received, or no operation is performed for 30 sec.

D Monitor switch action Sq

The monitor switch action cuts off the squelch function temporarily. This switch action contains PUSH (Pu) or HOLD (Ho) settings as shown below.
Pu (PUSH): After pushing the [SQL] for 1 sec., the squelch opens and emits audio while pushing and holding [SQL]. (default) Ho (HOLD): After pushing the [SQL] for 1 sec., the squelch opens and emits audio even [SQL] is released. To close the squelch, push any key.

PUSH

Auto scan OFF (default)

Auto scan ON

D Dual/Tri-watch function dt
This item selects dual or tri-watch as desired. See p. 15 for details.
PUSH

PUSH

Monitor action PUSH (default)

Monitor action Hold

D Automatic backlighting bL
Tri-watch function This function is convenient for nighttime operation. The automatic backlighting can be adjusted from OFF, 1 (dark)3 (bright); 3 (default). Select 13 to turn this function ON.
The automatic backlighting turns the backlighting ON when any key except for [PTT] is pushed. The backlighting is automatically turned OFF after 5 sec. of inactivity.

Dualwatch function (default)

PUSH

Automatic backlighting (default)

Automatic backlighting OFF 19

SET MODE D Self check function SC

The self check function checks transceiver conditions by itself, and informs you in case a problem is found. The following items are checked after the power is turned ON, then it switches to operation mode. Temperature : Outside of 35C to +73C; 31F to +163F (approx.) Connected battery voltage Water intrusion

D LCD contrast selection LC

The contrast of the LCD can be adjusted from 4 levels.
1 (bright) 4 (dark); 3 (default)

PUSH

LCD contrast 3 (default)

LCD contrast 1

D Auto power save function PS

The auto power save function reduces current drain by deactivating the receiver circuit for preset intervals. Self check OFF (default)
PUSH PUSH

Self check ON

Auto power save ON (default)

Auto power save OFF

When error messages as shown below are displayed, see trouble shooting for advice (p. 28).

Temperature error

Battery voltage error

Water intrusion error

20

SET MODE D Battery voltage indicator bt

This function contains display or non-display settings of the voltage of the connected battery pack when the power is ON.
The voltage of the connected battery pack is displayed for 2 sec. after power is turned ON.

SET MODE LIST

Function Beep tone function Weather alert function Indication "bP" "AL" "Pr" "St" "AS" "dt" "Sq" "bL" "LC" "PS" "SC" "bt" "cd" Switch OFF / ON* / US OFF* / ON OFF* / ON OFF* / ON OFF* / ON Dual* / Tri Push* / Hold OFF / 1 / 2 / 3* 1 / 2 / 3* / 4 OFF / ON* OFF* / ON OFF* / ON 1* / 2 / / 32

PUSH

Priority scan function Battery voltage ON Scan resume timer Auto scan function Dual/Tri-watch function Monitor switch action Automatic backlighting LCD contrast selection

Battery voltage OFF (default)

D Scrambler code cd (Available for I/S version only)

There are 32 codes (1 to 32) available for programming. In order to understand each other, all transceivers in your group must have the same scramble code.

PUSH

Auto power save function Scrambler code 1 (default) Scrambler code 32 Self check function Battery voltage indicator Scrambler code**
* default setting ** Available for I/S version only

21

BATTERY CHARGING
I Cautions
NEVER incinerate used battery packs. Internal battery gas may cause an explosion. NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry immediately (particularly the battery terminals) BEFORE attaching it to the transceiver. Otherwise, the terminals will become corroded, or cause connection failure, etc. NEVER short the terminals of the battery pack. Also, current may ow into nearby metal objects, such as a necklace, etc. Therefore, be careful when carrying with, or placing near metal objects, carrying in handbags, etc. AVOID leaving the battery pack in a fully charged, or completely discharged condition for long time. It causes shorter battery life. In case of leaving the battery pack unused for a long time, it must be kept safely after discharge, or use the battery until the battery indicator shows the middle level, then remove it from the transceiver. If your battery pack seems to have no capacity even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or very little), a new battery pack must be purchased.

I Battery charging
Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. CAUTION: To avoid damage to the transceiver, turn it OFF while charging. Recommended temperature range for charging: +10C to +40C (+50F to +104F) - The Li-Ion battery is functioning within 20C to +60C (4F to +140F) Use the specified chargers (BC-119N, BC-121N and BC152). NEVER use another manufacturers charger. Use the supplied AC adapter (BC-147A/E) for BC-152. NEVER use another manufacturers AC adapter.

Recommendation: Charge the supplied battery pack for a maximum of up to 10 hours. Li-Ion batteries are different from NiCd batteries in that it is not necessary to completely charge and discharge them to prolong the battery life. Therefore, charging the battery in intervals, and not for extended periods is recommended.
22

BATTERY CHARGING Charging connections

q Attach the BC-152 to a at surface, such as desk or cabin, etc., if desired. w Connect the AC adapter (BC-147A/E) as shown below. e Insert the battery pack with/without the transceiver into the charger. The charge indicator lights green. r Charge the battery pack approx. 910 hours, depending on the remaining power condition.
BP-227 IC-M88
Ensure sides of the battery pack are correctly aligned with the charger groves.

For your convenience:

Eyelet: USE a rubber band to secure the transceiver, if desired.

Charge indicator lights green when BP-227 (with/without IC-M88) is inserted.

Supplied screws AC adapter BC-152

23

BATTERY CHARGING

I Optional BP-226 battery case

When using the optional battery case attached to the transceiver, install 5 AA (R6) size alkaline batteries as illustrated at right. The IC-M88 meets JIS waterproof specication grade 7. However, the BP-226 meets JIS waterproof specication grade 4. q Hook your nger under the latch, and open the cover in the direction of the arrow (q). (Fig.1) w Then, install 5 AA (R6) size alkaline batteries. (Fig.2) Install the alkaline batteries only. Be sure to observe the correct polarity. Do not pin the ribbon under the batteries. e Close the cover with tting in the direction of the arrow (w) rst, then rm the latch in place (e). (Fig.1) Be sure to the gasket and the ribbon are set correctly, and do not protrude out of the battery case. (Fig.3) CAUTION: When installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batteries together. Keep battery contacts clean. Its a good idea to clean battery terminals once a week.

Fig.1 q

BP-226

Latch

Fig.2 Ribbon

Fig.3

Gasket

Ribbon

24

BATTERY CHARGING

I AD-100 installation
Install the AD-100 desktop charger adapter into the holder space of the BC-119N/121N. Connect the plugs of the BC-119N/121N to the AD-100 desktop charger adapter with the connector, then install the adapter into the charger with the supplied screws.

q Desktop charger adapter

w Screws supplied with the charger adapter Connectors

Plugs

25

BATTERY CHARGING

I Optional battery chargers

D Rapid charging with the BC-119N+AD-100
The optional BC-119N provides rapid charging of battery packs. The following are additionally required. AD-100 charger adapter An AC adapter (may be supplied with BC-119N depending on version).
IC-M88 BP-227 BP-227 AC adapter (Not supplied with some versions.) AD-100 charger adapter is installed in BC-119N. IC-M88

D Rapid charging with the BC-121N+AD-100

The optional BC-121N allows up to 6 battery packs to be charged simultaneously. The following are additionally required. Six AD-100 charger adapters An AC adapter (BC-124) or the DC power cable OPC-656, supplied with the BC-121N.

AC adapter (purchased separately)

AD-100 charger adapters are installed in each slot.

OPC-515L or CP-17L Optional OPC-515L (for 13.8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.

MUL

TI-C

ER HARG

DC power cable (supplied with the BC-121N) Connect with the DC power supply; 13.8 V/7 A minimum

26

SPEAKER-MICROPHONE
I HM-138 Description
Alligator type clip To attach the speaker-mic. to your shirt or collar, etc. PTT switch Transmits during push Receives during release
q

10

I Attachments
Insert the connector of the speaker-microphone into the [SP MIC] connector on the transceiver and tighten the screw.

Detaching: Unscrew (q), then detach the jack cover (w).

Microphone

Attaching: Attach the jack cover (e), then tighten the screw (r).
r

Speaker
CAUTION: Attach the speaker-microphone s connector securely to prevent accidental dropping, or water intrusion in the connector.

NEVER immerse the connector in water. If the connector becomes wet, be sure to dry it BEFORE attaching it to the transceiver. NOTE: The microphone is located at the top of the speaker-microphone, as shown in the diagram above. To maximize the readability of your transmitted signal (voice), hold the microphone approx. 5 to 10 cm (2 to 4 inches) from your mouth, and speak in a normal voice level.

IMPORTANT: KEEP the [SP MIC] jack cover attached (transceiver) when the speaker-microphone is not in use as illustrated above. Water will not get into the transceiver even if the cover is not attached, however, the terminals (pins) will become rusty, or the transceiver will function abnormally if the connector becomes wet. 27

11

TROUBLESHOOTING
POSSIBLE CAUSE SOLUTION. Recharge the battery pack. Check the connection to the transceiver. Set squelch to the threshold point. Set [VOL] to a suitable level. Drain water from the speaker. REF. p. 22 p. 5 p. 11 p. 10 pgs. 8, 9, 29 p. 22 p. 10

PROBLEM

The transceiver does The battery is exhausted. Bad connection to the battery pack. not turn ON. No sound from speaker. Squelch level is too deep. Volume level is too low. Speaker has been exposed to water.

Transmitting is impossi- Some channels are for low power or re- Change channels. ble, or high power can ceive only. Recharge the battery pack. The battery is exhausted. not be selected. Push [H/LLOCK] to select high power. The output power is set to low. The displayed channel Lock function is activated. cannot be changed. Scan does not start. No beeps. Self check error. (Temperature) Self check error. (Battery voltage) Self check error. (Water intrusion) TAG channels are not programmed. Beep tones are turned OFF.

Push [H/LLOCK] for 1 sec. to cancel the p. 12 function. Set the desired channels as TAG channels. p. 14 Set the beep tones to ON (Fix Beep/User p. 18 Beep) in SET mode.

The temperature is outside of 35C to Leave the transceiver at room temperature +73C; 31F to +163F (approx) for a while. Turn the power ON to check if the internal temperature has returned to normal. The connected battery packs voltage is Verify the battery voltage is correct. more than 8.8 V. Water has entered the transceiver. Have the transceiver checked at your local distributor or dealer to see whether the transceiver works properly or not.

28

VHF MARINE CHANNEL LIST

Channel number Frequency (MHz) USA INT CAN Transmit Receive 01 01A 02 03 03A 04 05 05A 06 07A 08 09 10 11 12 13* 14 15* 16 17* 18A 19 08 09 10 11 12 13 14 15* 16 17 18 06 07 08 09 10 11 12 13* 14 15* 16 17* 06 02 03 01 156.050 160.650 156.050 156.050 156.100 160.700 156.150 160.750 156.150 156.150 156.200 160.800 04A 156.200 156.200 156.250 160.850 05A 156.250 156.250 156.300 156.300 156.350 160.950 07A 156.350 156.350 156.400 156.400 156.450 156.450 156.500 156.500 156.550 156.550 156.600 156.600 156.650 156.650 156.700 156.700 156.750 156.750 156.800 156.800 156.850 156.850 156.900 161.500 18A 156.900 156.900 156.950 161.550 65A 64A 65 65A 63A 64 64 63 61A 62 23A 24 25 26 27 28 24 25 26 27 28 60 61 24 25 26 27 28 60 22A 23 21A 22 23 Channel number Frequency (MHz) USA INT CAN Transmit Receive 19A 20 20A 21 21 20 19A 156.950 156.950 20* 157.000 161.600 157.000 157.000 157.050 161.650 157.100 161.700 22A 157.100 157.100 157.150 161.750 157.150 157.150 157.200 161.800 157.250 161.850 157.300 161.900 157.350 161.950 157.400 162.000 156.025 160.625 156.075 160.675 61A 156.075 156.075 156.125 160.725 62A 156.125 156.125 156.175 160.775 156.175 156.175 156.225 160.825 83A 84 84A 84 156.275 160.875 65A 156.275 156.275 64A 156.225 156.225 82A 83 81A 82 83 84 80A 81 79A 80 78A 79 21A 157.050 157.050 Channel number Frequency (MHz) USA INT CAN Transmit Receive 66 66A 67* 68 69 70 71 72 73 74 77* 67 68 69 70 71 72 73 74 77 78 67 68 69 70 71 72 73 74 77* 156.325 160.925 156.375 156.375 156.425 156.425 156.475 156.475 Rx only 156.525 156.575 156.575 156.625 156.625 156.675 156.675 156.725 156.725 156.875 156.875 156.925 161.525 78A 156.925 156.925 156.975 161.575 79A 156.975 156.975 157.025 161.625 80A 157.025 157.025 157.075 161.675 81A 157.075 157.075 157.125 161.725 82A 157.125 157.125 157.175 161.775 157.225 161.825 157.225 157.225 83A 157.175 157.175 WX channel 1 2 3 4 5 6 7 8 9 10 66A 66A* 156.325 156.325 85 85A 86 86A 87 87A 88 88A 21b 25b 28b 83b 88 88 87 87 86 86 85 85

12

Channel number Frequency (MHz) USA INT CAN Transmit Receive 157.275 161.875 157.275 157.275 157.325 161.925 157.325 157.325 157.375 161.975 157.375 157.375 157.425 162.025 157.425 157.425 Rx only 161.650 Rx only 161.850 Rx only 162.000 Rx only 161.775

Frequency (MHz) Transmit RX only RX only RX only RX only RX only RX only RX only RX only RX only RX only Receive 162.550 162.400 162.475 162.425 162.450 162.500 162.525 161.650 161.775 163.275

*Low power only.

NOTE: Simplex channels 3, 21, 23, 61, 64, 81, 82 and 83 CANNOT be lawfully used by the general public in USA waters.

29

13
GENERAL

SPECIFICATIONS
RECEIVER
: 156.025157.425 MHz : 156.050163.275 MHz : 146.000174.000 MHz : 16K0G3E (Wide) : 16K0F3E (Wide)/8K50F3E (Narrow) : 25 kHz (Wide) 12.5 kHz (Narrow; LMR only) : TX High (5 W)1.6 A typical Max. audio 200 mA typical Power save 20 mA typical : 10.0 ppm (30C to +60C) : 20C to +60C; 4F to +140F : 30C to +60C; 22F to +140F : 62 (W) 97(H) 39(D) mm 2716(W) 31316(H) 11732(D) inch : 280 g (9.9 oz) Receive system Sensitivity (12 dB SINAD) Squelch sensitivity Intermodulation rejection ratio Spurious response rejection ratio Adjacent channel selectivity Hum and noise ratio Audio output power : Double-conversion superheterodyne : 0.25 V typical : Less than 0.35 V (at threshold) : 70 dB typical : 70 dB typical : 70 dB typical (Wide) 60 dB typical (Narrow; LMR only) : More than 40 dB (Wide) More than 34 dB (Narrow; LMR only) : 0.35 W typical at 10% distortion with an 8 load

Frequency coverage Marine TX RX LMR TX/RX Mode Marine LMR Channel spacing Current drain (at 7.2 V DC)

All stated specications are subject to change without notice or obligation.

Frequency stability Usable temperature range Marine LMR Dimensions (Projections not included) Weight (approx.; with BP-227)

TRANSMITTER
Output power (at 7.2 V DC) Modulation system Max. frequency deviation Audio harmonics distortion Spurious emissions : 5 W (Hi), 3 W (Mid) and 1 W (Low) : Variable reactance frequency modulation : 5 kHz (Wide) 2.5 kHz (Narrow; LMR only) : Less than 10% (at 60% mod.) : Less than 70 dBc typical

30

QUICK REFERENCE

q Cut w Fold e Complete

14

Important operating instructions are summed up in this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc.

iM88
I IN CASE OF EMERGENCY USING CHANNEL 16 DISTRESS CALL PROCEDURE 1. MAYDAY MAYDAY MAYDAY. 2. THIS IS (name of vessel) 3. Your call sign or other indication of the vessel. 4. LOCATED AT (your position) 5. The nature of the distress and assistance required. 6. Any other information which might facilitate the rescue.
USA/International/Canadian/LAND channels
U/I/C/L

31
<CUT HERE>

CHANNEL SELECTION (pgs. 8, 9)

Channel 16
9

Channel 9/Call channel

9

OPERATION GUIDE

Push

Push for 1 sec.

Weather channel
U/I/C/L

Push

Call channel programming (p. 12)

q Push [CH/WXU/I/C] for 1 sec. once

or several times, to select the desired channel group.

w Push [169] for 1 sec. to select the

call channel.
Push for 1 sec.

e Push [169] for 3 sec. (until long

beep changes to 2 short beeps)

r Push [Y]/[Z] to select the desired

channel.

t Push [169] to program the displayed channel as the call channel.

I SET MODE (pgs. 1721) q While pushing [SQL], turn power ON.
Push
LOCK

I LOCK FUNCTION (p. 12)

I WEATHER ALERT (p. 9) (Available for USA version only) q Turn the weather alert item in the
SET mode ON (p. 18).

w Push [SQL] again to select an item.

Refer to pgs. 1721 for set mode item.

for 1 sec. to turn the lock function ON and OFF.

w Select WX channel; or start scanning. I VOICE SCRAMBLER (p. 11) (Available for the I/S version only)

e Push [Y]/[Z] to select the desired

condition.

I TAG CHANNELS (p. 14) q Push [Y]/[Z] to select the desired

channel.

r Push [169] to return to regular operating mode.

I DUAL/TRI-WATCH (p. 15) q Push [Y]/[Z] to select the desired channel. w Push [SCNDUAL] for 1 sec. to start dualwatch or tri-watch depending on SET mode setting (p. 19).

w Push both [Y] and [Z] for 1 sec. to set the displayed channel as a tag channel. I SCAN (p.14)
Push [SCNDUAL] to start/stop scanning.

q Set a scrambler code in SET mode (p. 21).

Cannot be used on ch 16, 70 or weather channels.

w While pushing and holding [SQL], push [SCNDUAL] to turn the function ON and OFF.

OPTIONS
BP-226 BATTERY CASE Battery case for 5 AA (R6) alkaline cells. BP-227 Li-Ion BATTERY PACK 7.2 V/1700 mAh Li-Ion battery pack. The same as supplied with the transceiver. BP-227 must be charged with the supplied BC-152 or the optional BC-119N/121N. BC-119N DESKTOP CHARGER + AD-100 CHARGER ADAPTER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger. Charging time: approx. 2 to 2.5 hours BC-121N MULTI-CHARGER + AD-100 CHARGER ADAPTER (6 pcs.) + BC-124 AC ADAPTER For rapid charging of up to 6 battery packs (six AD-100s are required) simultaneously. An AC adapter may be supplied depending on version. Charging time: approx. 2 to 2.5 hours. BC-152 DESKTOP CHARGER + BC-147A/E AC ADAPTER Used for regular charging of battery pack. The same as supplied with the transceiver. Charging time: approx. 910 hours MB-86 SWIVEL BELT CLIP Swivel type belt clip. The same as supplied with the transceiver. HM-138 SPEAKER-MICROPHONE Full-sized waterproof (JIS grade 7; 1m/30 min.) speaker-microphone including alligator type clip to attach to your shirt or collar, etc.

15

33

Count on us!

A-6214H-1EX-w Printed in Japan 2002 Icom Inc.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0002 Japan