Scribd
Upload
241K views

Engineering Drawing Solved Sample Question Paper

a sample question paper,for practice with answers {all figures are drawn to the scale using MS-Word and Paint.by Prof. Vinay Chidri An alternaing way to CAD drafting softwares

Uploaded by

vinay chidri
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
241K views

Engineering Drawing Solved Sample Question Paper

a sample question paper,for practice with answers {all figures are drawn to the scale using MS-Word and Paint.by Prof. Vinay Chidri An alternaing way to CAD drafting softwares

Uploaded by

vinay chidri
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 10

F. Y. B.Tech.

(E) X—1050—2008
MAHARASHTRA INSTITUTE OF TECHNOLOGY
F. Y. B.Tech. (E) EXAMINATION

ENGINEERING DRAWING
(NOV/DEC 2008-09)
Time--Four Hours Maximum Marks--80
“Please check whether you have got the right question paper”
N. B. :-(i) Question Numbers 1 and 6 are compulsory.
(ii) Solve two questions each from remaining questions of Section A and Section B.
(iii) Assume suitable additional data if necessary, and mention it clearly.

Section A
Q.1. The projections of the ends of a line AB are on the same projector. The (
end A is 30 mm below H.P. and 15 mm behind V.P. The end B is 35 mm 14)
above H.P. and 40 mm in front of V.P. Determine its true length, the
traces and the inclinations with the reference planes.
Column width = 6 row height = 35.25
Q.2. A regular Hexagon ABCDEF of 30 mm side is the front view of a plate (
when its surface is inclined at 300 to the V.P. Draw the projections when 13)
its side AB is in V.P. and inclined at 450 to the H.P.

Q.3. A pentagonal pyramid, side of base 25 mm and height 60 mm has one (


of its slant (triangular) faces on the H.P. and the edge of base contained 13)
by that slant edge makes an angle 30 degree to the V.P. Draw its
projections.

Q.4. Three spheres of 40 mm diameter are placed on ground touching each (


other, with line joining centers of any two parallel to V.P. A fourth 13)
sphere of diameter 50 mm is placed centrally over these spheres,
determine the height of centre of the fourth sphere by means of
projections of the arrangement.

Q.5. A cone diameter of base 60 mm and height 70 mm is lying on the (


ground with on of the generators its axis parallel to V.P. It is cut by a 13)
vertical section plane inclined at 400 to the V.P. Draw the sectional front
view, top view and true shape of section.

Section B
Q.6. Figure 2, shows an isometric view of an object. Draw the following (14)
views. i) Front view in direction of arrow, ii) Top view, and iii) Side
view from right.

Q.7. Figure 1. shows front view of a cut cylinder with base diameter 60 mm. (
with its axis parallel to V.P. and perpendicular to H. P. Draw the 13)
development of the lateral surface of the part P of the cylinder

Q.8. Figure 3, shows two views of an object, draw an isometric view of the (
object. 13)

Q.9. Front view and top view of an object are given in Figure:- 4. (
Draw: i) Redraw the front view; ii) Sectional top view (section BB); 13)
and iii) Side view from right.
Figure:-1 (Q. 6.) Figure:-2 (Q.7.)

Figure:-3 (Q.8.) Figure:- 4 (Q.9.)


Q.1.

Q.2.

Inclination with HP; θ = 500


Inclination with VP; Ø = 400
True Length; TL = 85 mm.
Q.3.
Q. 4.
Q.5.

E
Q.6.
Q.7.
Q.8.
Q.9.

You might also like