Shrinkage Limit

SOIL MECHANICS
LAB REPORT Shrinkage Limit

Scope and Need of Practical:
As the soil loses moisture, either in its natural environment, or by artificial means in laboratory it changes from liquid state to plastic state to semi-solid state and then to solid state. The volume is also reduced by the decrease in water content. But, at a particular limit the moisture reduction causes no further volume change. A shrinkage limit test gives a quantitative indication of how much moisture can change before any significant volume change and to also indication of change in volume. The shrinkage limit is useful in areas where soils undergo large volume changes when going through wet and dry cycles (e.g. earth dams). This test method provides a procedure for obtaining the data which are used to calculate the shrinkage limit and the shrinkage ratio. The liquid limit, plastic limit, and shrinkage limit are often collectively referred to as the Atterberg Limits in recognition of their formation by Swedish soil scientist, A. Atterberg. These water contents distinguish the boundaries of the several consistency states of cohesive soils.This test method is performed only on that portion of a soil which passes the 425-m (No. 40) sieve. The relative contribution of this portion of the soil must be considered when using this test method to evaluate the properties of the soil as a whole.
Significance and use:

The shrinkage factors covered in this test method can only be determined on basically fine-grained (cohesive) soils which exhibit a dry strength when air dried. The term shrinkage limit, expressed as water content in percent, is typically assumed to represent the amount of water required to fill the voids of a given cohesive soil at its minimum void ratio obtained by drying (usually oven). Thus, the concept shrinkage limit can be used to evaluate the shrinkage potential or possibility of development, or both, of cracks in earthworks involving cohesive soils. Data obtained from this test method may be used to compute the volumetric shrinkage and linear shrinkage.
Apparatus:
Evaporating Dish of Porcelain Spatula and Straight Edge Balance-Sensitive to 0.01 g minimum. Shrinkage Dish. Circular, porcelain or non-corroding metal dish Glass cup. 50-55 mm in diameter and 25 mm in height Glass plates. Two, 75x75 mm one plate of plain glass and the other prongs Thermostatically controlled Oven Wash bottle containing distilled water Graduate-Glass, with capacity of 25 ml Mercury
Procedure:
Prepration of soil paste: Take about 100 gm of soil sample from a thoroughly mixed portion of the material passing through 425-mm I.S. sieve. Place about 30 gm the above soil sample in the evaporating dish and thoroughly mixed with distilled water and make a creamy paste. (Use water content slightly higher than the liquid limit.)
Filling the shrinkage dish: 1. Coat the inside of the shrinkage dish with a thin layer of Vaseline to prevent the soil sticking to the dish. 2. Fill the dish in three layers by placing approximately 1/3 rd of the amount of wet soil with the help of spatula. Tap the dish gently on a firm base until the soil flows over the edges and no apparent air bubbles exist. Repeat this process for 2nd and 3rd layers also till the dish is completely filled with the wet soil. Strike off the excess soil and make the top of the dish smooth. Wipe off all the soil adhering to the outside of the dish. 3. Weigh immediately, the dish with wet soil and record the weight. 4. Air- dry the wet soil cake for 6 to 8 hrs, until the colour of the pat turns from dark to light. Then oven-dry the cake at 1050C to 1100C say about 12 to 16 hrs. 5. Remove the dried disk of the soil from oven. Cool it in a desiccator. Then obtain the weight of the dish with dry sample. 6. Determine the weight of the empty dish and record. 7. Determine the volume of shrinkage dish which is evidently equal to volume of the wet soil as follows. Place the shrinkage dish in an evaporating dish and fill the dish with mercury till it overflows slightly. Press it with plain glass plate firmly on its top to remove excess mercury. Pour the mercury from the shrinkage dish into a measuring jar and find the shrinkage dish volume directly. Record this volume as the volume of wet soil pat. Volume of dry soil pat: Determine the volume of dry soil pat by removing the pat from the shrinkage dish and immersing it in the glass cup full of mercury in the following manner. Place the glass cup in a larger one and fill the glass cup to overflowing with mercury. Remove the excess mercury by covering the cup with glass plate with prongs and pressing it. See that no air bubbles are entrapped. Wipe out the outside of the glass cup to remove the adhering mercury. Then, place it in another larger dish, which is, clean and empty carefully. Place the dry soil pat on the mercury. It floats submerge it with the pronged glass plate which is again made flush with top of the cup. The mercury spills over into the larger plate. Pour the mercury that is displayed by the soil pat into the measuring jar and find the volume of the soil pat directly.
Observation and calculations:

Wt of shrinkage dish=11 gms Wt of dish+mercury=290 gms Wt of coated dish=12 gms
Sample 1:
Wt of coated dish+wet sample=49 Wt of dry sample=38 11 gms of water
Sample 2:
Wt of coated dish+wet sample=45 Wt of dry sample=35 10 gms of water
To find volume:
Wt of can=70 gms Wt of mercury +can=3216 Wt of mercury=224 for sample 1 Wt of mercury=202 for sample 2
Computations and Interpretation
Steps to calculation of shrinkage limit:
First determine moisture content Determine volume of wet soil Determine volume of dry soil Determine weight of dry soil Use the following formula for shrinkage limit:
Shrinkage limit (S.L) = [w [(V-Vo)w/Wo] x 100] Where: w = Moisture content of the wet soil V = Volume of wet soil Vo = Volume of dry soil Wo = Weight of oven dry soil w = Density of water (1 g/cm3)
Calculate shrinkage ratio

Observations And Calculations:
Weight of wet soil (Mw) Weight of dry soil (MO) Volume of mercury (V) Volume of mercury (VO) Moisture content (w) Shrinkage Limit (SL) Shrinkage Ratio (R)
49 45
38 35
20.5 20.5
16.47 14.85
22.44 % 28.57 %
11.83 12.42
2.30 2.35

Shrinkage Limit

Uploaded by

Copyright:

Available Formats

Shrinkage Limit

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Shrinkage Limit

Uploaded by

Copyright:

Available Formats

SOIL MECHANICS

LAB REPORT Shrinkage Limit

Significance and use:

Observation and calculations:

Computations and Interpretation

Steps to calculation of shrinkage limit:

Calculate shrinkage ratio

You might also like