Bulletin 66000e

CASING RUNNINGTM

CASING DRILLING

CASING & TUBING

TORQUE
TABLES
API Round Thread
API Buttress
TESCO MLT Rings*
Imperial and Metric Units

FIELD MAKE-UP
HANDBOOK
Third Edition
The Drilling Innovation Company
www.tescocorp.com

The information contained in this

document is provided as a service by
TESCO C o r p o r a t i o n , i t s s u b s i d i a r i e s
and affiliates. We have tried to provide
quality information, but we make no
claims, promises or guarantees about
the accuracy, completeness, or adequacy
of the information contained in this
document. Readers are cautioned that
they use the materials and products
referred to in this document, and follow
the procedures recommended herein,
entirely at their own risk.

Page 

MLT Ring Field Make-Up Handbook

TABLE OF CONTENTS

I.

TORQUE TABLES
a. Introduction
b. Tubing EUE Torque Tables
c. Casing SHORT Round Torque Tables
d. Casing LONG Round Torque Tables
e. Casing BUTTRESS Torque Tables

Ib.





II.

METRIC TABLES
a. Tubing EUE Torque Tables - Metric
b. Casing SHORT Round Torque Tables - Metric
c. Casing LONG Round Torque Tables - Metric
d. Casing BUTTRESS Torque Tables - Metric

III.

TESCO MLT (Multi-Lobe Torque) Rings

a. Applications
b. Features MLT Rings
c. Performance & Applications
d. Ring Identification
e. Recommended Practices for Field Make-up
with MLT Rings
f. Field Ring Installation
(floating rings without install kit)

RECOMMENDED PRACTICES
API Casing and Tubing Threads
a. Storage and Handling Casing
b. Preparation for Running Casing
c. General Practices for Field Make-up, API Round
and BUTTRESS Threads (without MLT Rings)
d. Practices for ROUND Thread Casing,
Sizes 4-1/2 Through 13-3/8
e. Practices for BUTTRESS Thread Casing,
Sizes 4-1/2 Through 13-3/8
f. Practices for ROUND and BUTTRESS Thread
Casing, Sizes 16, 18-5/8 and 20

Page
4
10
11
15
20
26
27
31
36

42
42
42

44
45

47
47
49
49
50
51
52
56

IV. BREAKING OUT CONNECTIONS

57

APPENDIX A Definitions

58

APPENDIX B References

58

APPENDIX C THREAD MAKE-UP LOSS FACTORS

59

APPENDIX D Conversion factors

61

MLT Ring Field Make-Up Handbook

Page 

I. INTRODUCTION TO TORQUE TABLES

API Round Thread
API Buttress Thread
TESCO MLT Rings
These Torque Tables and Recommended Practices provide
performance ratings and field practices for power tight
assembly of new API Round and Buttress threads. The
torque values in the tables for Round thread casing and
tubing without MLT rings are in accordance with API
Recommended Practice 5C1. The torque values in the tables
for TESCO MLT rings are in accordance with TESCO
recommended practices when used with new API tubing and
casing connections. Previously made-up threads, particularly
tubing, may demonstrate reduced torques due to permanent
deformation of pin and/or coupling.
Torque values and friction coefficients are affected by a
large number of variables, such as variations in taper, lead,
thread height and thread forms, surface finish, type of thread
compound, length of thread, coatings and weight and grade
of pipe. The torque values represented in the tables are for
API Modified thread compound. Use of other compounds
may result in different torques.
The API Round thread torque values (referred to as shoulder
torques) included in the tables herein apply to connections
with zinc-plated or phosphatecoated couplings. For API
Round thread connections with other coupling coatings or
platings, couplings with the modified feature (seal rings), or
using thread compounds other than API Modified, the Round
thread (shoulder) torques in the tables herein should be
adjusted by multiplying torques by the following factors:

Factor
Tin plated couplings:

0.80
Couplings with PTFE (Teflon) rings 0.70

Note: All round thread reflected in the text and following

tables are 8 threads per inch, commonly referred to as 8Round.

Page 

MLT Ring Field Make-Up Handbook

HOW TO USE THESE TABLES

Please refer to the recommended practices that accompany
these tables.
API Round Thread (without MLTTM Rings).
For API Round thread connections the recommended
practice for power tight assembly includes using the API
specified make-up torque as the primary criteria, and
position of the pin end in the coupling as the secondary
criteria for make-up.
Imperial Example: 7 23# K-55 LTC
The torque for power tight make-up should fall
between the minimum and maximum torques of
2,560 ft-lbs and 4,260 ft-lbs, respectively (Optimum
= 3,410 ft-lbs)
Metric Example: 177.80mm 34.23 Kg/m K-55 LTC
The torque for power tight make-up should fall
between the minimum and maximum torques of
3,470 Nm and 5,780 Nm, respectively
(Optimum = 4,620 Nm)
API Buttress Thread (without MLTTM Rings).
For API Buttress thread connections the recommended
practice for power tight assembly includes using the
position of the pin in the coupling as the primary criteria for
make-up, then using the observed torque for that position
as an aid to run the casing.
Imperial Example: 7 23# K-55 BTC
The pin should be made up in the coupling until
the end of the coupling reaches the base of the
triangle stamped on the pin end. After making up
several connections in this manner the observed
torque should then be used to make up the rest
of the string. (Note estimates of the make-up
shoulder torques for buttress are referenced in
the table, i.e., approximately 7,000 ft-lbs for this
connection)
Metric Example: 177.80 mm 34.23 Kg/m K-55 BTC
The pin should be made up in the coupling until
the end of the coupling reaches the base of the
triangle stamped on the pin end. After making up
MLT Ring Field Make-Up Handbook

Page 

several connections in this manner the observed

torque should then be used to make up the rest
of the string. (Note estimates of the make-up
shoulder torques for buttress are referenced in
the table, i.e., approximately 9,490 Nm for this
connection)
API Round and Buttress Thread with MLT Rings
The MLT ring provides a significant boost in torque
capacity to round and buttress thread connections. The
total torque capacity is determined as follows:

TorqueTotal = TorqueShoulder + TorqueDelta

Where,
TorqueShoulder = Torque to bring pin end into

contact with the MLT ring

Actual shoulder torques are determined during make-up

in the field. They can be estimated with the tables herein
using as the shoulder torque the API Recommended
Torques for round thread or the tabulated estimated
make-up torque shown for buttress threads.

and

TorqueDelta =

Additional torque capacity

available from the contact of the
pin end and MLT ring

Delta Torques are calculated on the basis of predicted

yield of the ring or pin end, whichever occurs first. The

Delta Torques in the table are for L-80 grade rings. In
cases where ring strength limits the torque, higher torque
ratings may result from the use of higher strength rings.

Total Torques. Values for TorqueTotal are provided

in the tables. For round thread the shoulder torque

is conservatively assumed to be the minimum API
recommended torque. Where the shoulder torque is
higher then total torque will also be higher.

Page 

MLT Ring Field Make-Up Handbook

Imperial Example: 7 23# N-80 LTC

For Shoulder Torque = API Minimum Torque
TorqueShoulder = 3,320 ft-lbs from the LONG


thread table (minimum)
TorqueDelta =
4,400 ft-lbs from the LONG


table
TorqueTotal =
3,320 + 4,400 = 7,720 ft-lbs
For Shoulder Torque = API Optimum Torque
TorqueShoulder =
4,420 ft-lbs from the LONG


thread table (optimum)
TorqueDelta =
4,400 ft-lbs from the LONG


table
Torque Total =
4,420 + 4,400 = 8,820 ft-lbs
Metric Example: 177.80 mm 34.23 Kg/m N-80 LTC
For Shoulder Torque = API Minimum Torque
TorqueShoulder =
4,500 Nm from the LONG


thread table (minimum)
TorqueDelta =
5,970 Nm from the LONG


table
TorqueTotal =
4,500 + 5,970 = 10,470 Nm
For Shoulder Torque = API Optimum Torque
TorqueShoulder =
5,990 Nm from the LONG


thread table (optimum)
TorqueDelta =
5,970 Nm from the LONG


table
Torque Total =
5,990 + 5,970 = 11,960 Nm
TECHNICAL SERVICES NOTE:
Higher torque performance using the MLT Ring may be
available depending on the casing or tubing and the operator
design requirements. Additional design assistance is
available by contacting TESCO as noted below:
TESCO CORPORATION
Casing Accessory Products
11330 Brittmoore Park Drive
Houston, Texas 77041
713-849-5900
Email: [email protected]

MLT Ring Field Make-Up Handbook

Page 

Notes to tables:
1. API Recommended Torques are from API RP 5C1,
Eighteenth Edition, May 1999 and apply to NEW
threads. Previously made-up threads, particularly tubing,
may demonstrate reduced torques due to permanent
deformation of pin and/or coupling.
2. Ring ID is prior to forming lobes, i.e., diameter equivalent
to ring circumference. In some cases the ring ID is
less than the pipe ID and for these cases the ring ID is
highlighted in yellow.

Example 3.970 inches or 100.84 mm

3. Torque Total = Torque Shoulder + Torque Delta

where:

a. Torque Shoulder for round thread is conservatively

taken as the Minimum API Recommended Torque.

b. Torque Shoulder for buttress thread is the estimated

make-up torque shown in the tables and is generally
conservative. Caution Field torque values will
vary and torque table values for buttress are
approximation only.

c. Torque Total is provided as a range of Min and Max

for round thread depending on the actual shoulder
torque observed in the field. A Max torque is

provided for buttress thread.

4. Delta torque is the torque boost provided by the MLT

ring and is added to the shoulder torque to provide the
total torque. For buttress threads, the Delta torque is
conservatively limited by the elastic limit of the ring or pin
in compression. For round threads, the Delta toque is
conservatively limited by the elastic limit of the ring or pin
in compression, or a lower limit to retain sealing contact
between the mated pin and coupling threads, whichever
is lower.
5. The conservatism built into these ratings allows higher
torque values depending on circumstances. Contact
TESCO for specific applications.
6. MLT rings are made from API grade L-80 steel and
have the mechanical properties of L-80. If desired, higher
torque capacity is available by using higher strength
rings.
Page 

MLT Ring Field Make-Up Handbook

IMPERIAL TABLES
Pages 10-25
---------------------------METRIC TABLES
Pages 26-41

MLT Ring Field Make-Up Handbook

Page 

EUE 8-Round Thread

with MLT Ring (L-80)
API Tubing EUE 8-Round Thread

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)
4.70

H-40
J-55
L-80
N-80
C-90
T-95
P-110

0.190
0.190
0.190
0.190
0.190
0.190
0.190

1.995
1.995
1.995
1.995
1.995
1.995
1.995

740
970
1,320
1,350
1,440
1,520
1,790

5.95

L-80
N-80
C-90
T-95
P-110

0.254
0.254
0.254
0.254
0.254

1.867
1.867
1.867
1.867
1.867

1,640
1,680
1,790
1,890
2,210

6.50

H-40
J-55
L-80
N-80
C-90
T-95
P-110

0.217
0.217
0.217
0.217
0.217
0.217
0.217

2.441
2.441
2.441
2.441
2.441
2.441
2.441

940
1,240
1,690
1,730
1,850
1,950
2,280

7.90

L-80
N-80
C-90
T-95
P-110

0.276
0.276
0.276
0.276
0.276

2.323
2.323
2.323
2.323
2.323

8.70

L-80
N-80
C-90
T-95
P-110

0.308
0.308
0.308
0.308
0.308

9.30

H-40
J-55
L-80
N-80
C-90
T-95
P-110

12.95

L-80
N-80
C-90
T-95
P-110

Page 10

2 3/8

990
1,290
1,760
1,800
1,920
2,030
2,380

1,240
1,610
2,200
2,250
2,400
2,540
2,980

2.065
2.065
2.065
2.065
2.065
2.065
2.065

560
620
620
620
620
620
620

1,300
1,590
1,940
1,970
2,060
2,140
2,410

1,800
2,230
2,820
2,870
3,020
3,160
3,600

2,190
2,240
2,390
2,520
2,950

2,740
2,800
2,990
3,150
3,690

1.957
1.957
1.957
1.957
1.957

850
850
850
850
850

2,490
2,530
2,640
2,740
3,060

3,590
3,650
3,840
4,000
4,540

1,250
1,650
2,250
2,300
2,460
2,600
3,040

1,560
2,060
2,810
2,880
3,080
3,250
3,800

2.521
2.521
2.521
2.521
2.521
2.521
2.521

900
1,010
1,010
1,010
1,010
1,010
1,010

1,840
2,250
2,700
2,740
2,860
2,960
3,290

2,460
3,070
3,820
3,890
4,090
4,260
4,810

2,030
2,080
2,230
2,340
2,750

2,710
2,770
2,970
3,120
3,660

3,390
3,460
3,710
3,900
4,580

2.413
2.413
2.413
2.413
2.413

1,350
1,350
1,350
1,350
1,350

3,380
3,430
3,580
3,690
4,100

4,740
4,810
5,060
5,250
5,930

2.259
2.259
2.259
2.259
2.259

2,210
2,270
2,420
2,550
2,990

2,950
3,020
3,230
3,400
3,980

3,690
3,780
4,040
4,250
4,980

2.349
2.349
2.349
2.349
2.349

1,540
1,540
1,540
1,540
1,540

3,750
3,810
3,960
4,090
4,530

5,230
5,320
5,580
5,790
6,520

0.254
0.254
0.254
0.254
0.254
0.254
0.254

2.992
2.992
2.992
2.992
2.992
2.992
2.992

1,300
1,710
2,270
2,400
2,570
2,720
3,170

1,730
2,280
3,030
3,200
3,430
3,620
4,230

2,160
2,850
3,790
4,000
4,290
4,530
5,290

3.086
3.086
3.086
3.086
3.086
3.086
3.086

1,610
1,890
1,890
1,890
1,890
1,890
1,890

2,910
3,600
4,160
4,290
4,460
4,610
5,060

3,770
4,740
5,680
5,890
6,180
6,420
7,180

0.375
0.375
0.375
0.375
0.375

2.750
2.750
2.750
2.750
2.750

3,150
3,220
3,460
3,640
4,260

4,200
4,290
4,610
4,850
5,680

5,250
5,360
5,760
6,060
7,100

2.840
2.840
2.840
2.840
2.840

3,000
3,000
3,000
3,000
3,000

6,150 8,250
6,220 8,360
6,460 8,760
6,640 9,060
7,260 10,100

2 7/8

3 1/2

MLT Ring Field Make-Up Handbook

 API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)
H-40
J-55
K-55

0.205 4.090
0.205 4.090
0.205 4.090

10.50

J-55
K-55
M-65

0.224 4.052
990
0.224 4.052 1,100
0.224 4.052 1,160

1,320 1,650
1,460 1,830
1,540 1,930

11.60

J-55
K-55

0.250 4.000 1,160

0.250 4.000 1,280

1,540 1,930
1,700 2,130

11.50

J-55
K-55
M-65

0.220 4.560 1,000

0.220 4.560 1,100
0.220 4.560 1,160

1,330 1,660
1,470 1,840
1,550 1,940

13.00

J-55
K-55
M-65

0.253 4.494 1,270

0.253 4.494 1,400
0.253 4.494 1,470

15.00

J-55
K-55

0.296 4.408 1,550

0.296 4.408 1,710

14.00

H-40
J-55
K-55

0.244 5.012
980
0.244 5.012 1,290
0.244 5.012 1,420

15.50

J-55
K-55
M-65

0.275 4.950 1,520

0.275 4.950 1,670
0.275 4.950 1,760

17.00

J-55
K-55

0.304 4.892 1,720

0.304 4.892 1,890

20.00

H-40
J-55
K-55
M-65

0.288
0.288
0.288
0.288

24.00

J-55
K-55

0.352 5.921 2,360

0.352 5.921 2,570

3,140 3,930
3,420 4,280

17.00

H-40

0.231 6.538

1,220 1,530

20.00

H-40
J-55
K-55
M-65

0.272
0.272
0.272
0.272

23.00

J-55
K-55

0.317 6.366 2,130

0.317 6.366 2,320

26.00

J-55
K-55

0.362 6.276 2,510

0.362 6.276 2,730

6.456
6.456
6.456
6.456

1,380
1,840
2,000
2,140

920
1,320
1,760
1,910
2,050

MLT Ring Field Make-Up Handbook

770
960
1,010 1,260
1,120 1,400

3.970
3.970

1,590 2,750
1,590 2,870

3,520
3,720

1,690 2,110
1,860 2,330
1,960 2,450

4.460
4.460
4.460

1,970 3,240
1,970 3,370
2,070 3,540

4,080
4,300
4,520

2,070 2,590
2,280 2,850

4.408
4.408

2,580 4,130
2,580 4,290

5,170
5,430

2,020 2,530
2,220 2,780
2,350 2,940

4.950
4.950
4.950

2,540 4,060
2,540 4,210
2,540 4,300

5,070
5,320
5,480

2,290 2,860
2,520 3,150

4.892
4.892

3,240 4,960
3,240 5,130

6,100
6,390

2,840 3,550
3,090 3,860

6.366
6.366

5,070 7,200
5,520 7,840

9,120
9,430

3,340 4,180
3,640 4,550

6.276
6.276

5,950 8,460 11,170

6,470 9,200 11,540

5 1/2

1,300 1,630
1,720 2,150
1,890 2,360

6 5/8

1,840
2,450
2,670
2,850

2,300
3,060
3,340
3,560

1,760
2,340
2,540
2,730

2,200
2,930
3,180
3,410

Page 11

8-Round SHORT Threads

6.049
6.049
6.049
6.049

580
760
840

4 1/2

9.50

8-Round SHORT Threads

API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)

7 5/8

24.00

H-40

0.300 7.025 1,590

26.40

J-55
K-55
M-65

0.328 6.969 2,360

0.328 6.969 2,570
0.328 6.969 2,760

24.00

J-55
K-55
M-65

0.264 8.097 1,830

0.264 8.097 1,970
0.264 8.097 2,140

28.00

H-40
M-65

0.304 8.017 1,750

0.304 8.017 2,720

2,330 2,910
3,620 4,530

32.00

H-40
J-55
K-55
M-65

0.352
0.352
0.352
0.352

2,790
3,720
4,020
4,350

36.00

J-55
K-55
M-65

0.400 7.825 3,260

0.400 7.825 3,510
0.400 7.825 3,800

32.30

H-40

0.312 9.001 1,910

36.00

H-40
J-55
K-55
M-65

0.352
0.352
0.352
0.352

40.00

J-55
K-55
M-65

0.395 8.835 3,390

0.395 8.835 3,650
0.395 8.835 3,960

32.75

H-40

0.279 10.192 1,540

40.50

H-40
J-55
K-55
M-65

0.350
0.350
0.350
0.350

45.50

J-55
K-55
M-65

0.400 9.950 3,700

0.400 9.950 3,960
0.400 9.950 4,320

51.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.450
0.450
0.450
0.450
0.450
0.450
0.450
0.450

Page 12

7.921
7.921
7.921
7.921

8.921
8.921
8.921
8.921

10.050
10.050
10.050
10.050

9.850
9.850
9.850
9.850
9.850
9.850
9.850
9.850

2,090
2,790
3,020
3,260

2,210
2,960
3,170
3,450

2,360
3,150
3,380
3,680

2,120 2,650
3,150 3,940
3,420 4,280
3,680 4,600

6.969
6.969
6.969

5,610 7,970 10,810

6,110 8,680 11,150
6,570 9,330 11,480

8.017
8.017

4,170 5,920 8,370

6,490 9,210 11,690

7.825
7.825
7.825

7,700 10,960 17,520

8,290 11,800 17,940
8,970 12,770 19,290

3,680
4,930
5,290
5,750

8.921
8.921
8.921
8.921

5,250
7,020
7,520
8,190

4,520 5,650
4,860 6,080
5,280 6,600

8.835
8.835
8.835

8,010 11,400 19,000

8,620 12,270 20,450
9,360 13,320 22,200

8 5/8

2,440 3,050
2,630 3,290
2,850 3,560

3,490
4,650
5,030
5,440

4,340 5,430
4,680 5,850
5,060 6,330

9 5/8

2,540 3,180

2,940
3,940
4,230
4,600

7,460
9,980
10,690
11,640

12,420
16,630
17,630
18,430

10 3/4

2,050 2,560

3,140
4,200
4,500
4,910

3,930
5,250
5,630
6,140

4,930 6,160
5,280 6,600
5,760 7,200

4,240 5,650
4,550 6,060
4,960 6,610
5,960 7,940
6,030 8,040
6,590 8,790
6,950 9,270
8,090 10,790

7,060
7,580
8,260
9,930
10,050
10,990
11,590
13,490

10.050
10.050
10.050
10.050

5,610
7,480
8,030
8,740

7,970
10,630
11,410
12,420

13,280
17,720
19,010
20,730

9.950 8,750 12,450 20,730

9.950 9,370 13,330 22,220
9.950 10,210 14,530 24,220
9.850
9.850
9.850
9.850
9.850
9.850
9.850
9.850

9,990
10,720
11,670
14,020
14,190
15,510
16,350
19,040

14,230
15,270
16,630
19,980
20,220
22,100
23,300
27,130

23,690
25,440
27,700
33,290
33,700
35,790
36,390
38,290

MLT Ring Field Make-Up Handbook

 API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)

10 3/4 (continued)

55.50

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.495
0.495
0.495
0.495
0.495
0.495
0.495

9.760
9.760
9.760
9.760
9.760
9.760
9.760

5,520 7,360 9,200

6,630 8,840 11,050
6,710 8,950 11,190
7,340 9,790 12,240
7,740 10,320 12,900
9,020 12,020 15,030
10,130 13,500 16,880

9.760
9.760
9.760
9.760
9.760
9.760
9.760

12,940
15,540
15,730
17,210
18,150
21,150
23,750

18,460
22,170
22,440
24,550
25,890
30,170
33,880

30,770
36,960
37,420
40,940
41,830
43,960
45,810

60.70

C-90
T-95
P-110
Q-125

0.545
0.545
0.545
0.545

9.660
9.660
9.660
9.660

8,170
8,610
10,030
11,270

10,890
11,480
13,370
15,020

13,610
14,350
16,710
18,780

9.660
9.660
9.660
9.660

19,060
20,090
23,400
26,290

27,230
28,700
33,430
37,560

45,360
47,780
50,140
52,210

65.70

C-90
T-95
P-110
Q-125

0.595
0.595
0.595
0.595

9.560
9.560
9.560
9.560

8,990
9,470
11,030
12,390

11,980
12,630
14,710
16,520

14,980
15,790
18,390
20,650

42.00

H-40

0.333 11.084 2,300

47.00

J-55
K-55
M-65

0.375 11.000 3,580

0.375 11.000 3,820
0.375 11.000 4,180

4,770 5,960 11.000

5,090 6,360 11.000
5,570 6,960 11.000

54.00

J-55
K-55
M-65

0.435 10.880 4,260

0.435 10.880 4,550
0.435 10.880 4,980

5,680 7,100 10.880 10,050 14,310 23,860

6,060 7,580 10.880 10,740 15,290 25,470
6,640 8,300 10.880 11,750 16,730 27,890

60.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.489
0.489
0.489
0.489
0.489
0.489
0.489
0.489
0.489

10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772

4,870
5,200
5,690
6,850
6,930
7,580
8,000
9,320
10,460

6,490
6,930
7,590
9,130
9,240
10,110
10,660
12,420
13,950

8,110
8,660
9,490
11,410
11,550
12,640
13,330
15,530
17,440

10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772

11,440
12,210
13,370
16,090
16,280
17,800
18,790
21,890
24,570

16,310
17,410
19,060
22,940
23,210
25,380
26,790
31,210
35,030

27,160
29,000
31,780
38,210
38,680
42,330
44,640
49,730
51,640

65.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.534
0.534
0.534
0.534
0.534
0.534

10.682
10.682
10.682
10.682
10.682
10.682

7,550
7,640
8,370
8,830
10,280
11,540

10,070
10,190
11,160
11,770
13,700
15,390

12,590
12,740
13,950
14,710
17,130
19,240

10.682
10.682
10.682
10.682
10.682
10.682

17,660
17,870
19,580
20,650
24,040
26,990

25,210
25,510
27,950
29,480
34,320
38,530

42,040
42,540
46,580
49,120
56,260
58,370

3,070 3,840
8,500 12,080 20,100
9,060 12,880 21,450
9,910 14,090 23,460

Page 13

8-Round SHORT Threads

MLT Ring Field Make-Up Handbook

11 3/4

8-Round SHORT Threads

API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)

13 3/8

48.00

H-40

0.330 12.715 2,420

54.50

J-55
K-55
M-65

0.380 12.615 3,860

0.380 12.615 4,100
0.380 12.615 4,520

5,140 6,430 12.575 9,140 13,000 21,660

5,470 6,840 12.575 9,710 13,810 23,040
6,020 7,530 12.575 10,710 15,230 25,370

61.00

J-55
K-55
M-65

0.430 12.515 4,460

0.430 12.515 4,750
0.430 12.515 5,230

5,950 7,440 12.575 10,570 15,030 25,070

6,330 7,910 12.575 11,250 16,000 26,650
6,970 8,710 12.575 12,390 17,620 29,340

68.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.480
0.480
0.480
0.480
0.480
0.480
0.480
0.480

12.415
12.415
12.415
12.415
12.415
12.415
12.415
12.415

72.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.514
0.514
0.514
0.514
0.514
0.514

12.347
12.347
12.347
12.347
12.347
12.347

65.00

H-40

0.375 15.250 4,390

75.00

J-55
K-55
M-65

0.438 15.124 7,100

0.438 15.124 7,520
0.438 15.124 8,320

84.00

J-55
K-55
M-65

0.495 15.010 8,170

0.495 15.010 8,650
0.495 15.010 9,570

87.50

H-40
J-55
K-55
M-65

0.435
0.435
0.435
0.435

17.755
17.755
17.755
17.755

5,590
7,540
7,940
8,840

94.00

H-40
J-55
K-55
M-65

0.438
0.438
0.438
0.438

19.124
19.124
19.124
19.124

5,810
7,840
8,240
9,190

106.50

J-55
K-55

0.500 19.000 9,130

0.500 19.000 9,600

133.00

J-55
K-55
M-65

0.635 18.730 11,920

0.635 18.730 12,530
0.635 18.730 13,980

Page 14

3,220 4,030

5,060 6,750 8,440 12.575

5,390 7,180 8,980 12.575
5,930 7,910 9,890 12.575
7,140 9,520 11,900 12.575
7,220 9,630 12,040 12.575
7,930 10,570 13,210 12.575
8,360 11,140 13,930 12.575
9,730 12,970 16,210 12.575
7,720
7,800
8,570
9,030
10,510
11,820

10,290
10,400
11,420
12,040
14,010
15,760

12,860
13,000
14,280
15,050
17,510
19,700

12.575
12.575
12.575
12.575
12.575
12.575

11,990
12,770
14,050
16,910
17,100
18,790
19,800
23,050

17,050
18,160
19,980
24,050
24,320
26,720
28,160
32,780

28,430
30,250
33,320
40,090
40,560
44,500
45,580
47,860

18,290
18,480
20,300
21,390
24,900
28,000

26,010
26,280
28,870
30,420
35,410
39,820

43,330
43,800
45,930
46,700
49,160
51,350

16

18 5/8

20

MLT Ring Field Make-Up Handbook

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)
J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250

4.000
4.000
4.000
4.000
4.000
4.000
4.000
4.000

1,220
1,350
1,410
1,670
1,710
1,840
1,940
2,270

13.50

M-65
L-80
N-80
C-90
T-95
P-110

0.290
0.290
0.290
0.290
0.290
0.290

3.920
3.920
3.920
3.920
3.920
3.920

1,710
2,030
2,070
2,230
2,350
2,750

15.10

P-110
Q-125

13.00

4 1/2
1,620
1,800
1,880
2,230
2,280
2,450
2,580
3,020

2,030
2,250
2,350
2,790
2,850
3,060
3,230
3,780

3.970
3.970
3.970
3.970
3.970
3.970
3.970
3.970

1,520
1,520
1,550
1,550
1,550
1,550
1,550
1,550

2,740
2,870
2,960
3,220
3,260
3,390
3,490
3,820

3,550
3,770
3,900
4,340
4,400
4,610
4,780
5,330

2,280
2,710
2,760
2,970
3,130
3,660

2,850
3,390
3,450
3,710
3,910
4,580

3.914
3.914
3.914
3.914
3.914
3.914

1,870
1,870
1,870
1,870
1,870
1,870

3,580
3,900
3,940
4,100
4,220
4,620

4,720
5,260
5,320
5,580
5,780
6,450

0.337 3.826 3,300

0.337 3.826 3,680

4,400 5,500
4,910 6,140

3.826
3.826

2,540 5,840
2,540 6,220

8,040
8,680

J-55
K-55
M-65

0.253 4.494 1,370

0.253 4.494 1,510
0.253 4.494 1,590

1,820 2,280
2,010 2,510
2,120 2,650

4.434
4.434
4.434

1,740 3,110
1,740 3,250
2,050 3,640

4,020
4,250
4,700

15.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.296
0.296
0.296
0.296
0.296
0.296
0.296
0.296

4.408
4.408
4.408
4.408
4.408
4.408
4.408
4.408

1,670
1,850
1,940
2,310
2,360
2,540
2,670
3,130

2,230
2,460
2,590
3,080
3,140
3,380
3,560
4,170

2,790
3,080
3,240
3,850
3,930
4,230
4,450
5,210

4.408
4.408
4.408
4.408
4.408
4.408
4.408
4.408

2,300
2,300
2,300
2,300
2,300
2,300
2,300
2,300

3,970
4,150
4,240
4,610
4,660
4,840
4,970
5,430

5,090
5,380
5,540
6,150
6,230
6,530
6,750
7,510

18.00

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.362
0.362
0.362
0.362
0.362
0.362
0.362

4.276
4.276
4.276
4.276
4.276
4.276
4.276

2,480
2,950
3,000
3,230
3,410
3,980
4,450

3,310
3,930
4,000
4,310
4,550
5,310
5,930

4,140
4,910
5,000
5,390
5,680
6,640
7,410

4.276
4.276
4.276
4.276
4.276
4.276
4.276

3,540
3,540
3,540
3,540
3,540
3,540
3,540

6,020 7,680
6,490 8,450
6,540 8,540
6,770 8,930
6,950 9,220
7,520 10,180
7,990 10,950

21.40

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.437
0.437
0.437
0.437
0.437
0.437
0.437

4.126
4.126
4.126
4.126
4.126
4.126
4.126

3,070
3,650
3,710
4,010
4,220
4,940
5,510

4,090
4,860
4,950
5,340
5,620
6,580
7,340

5,110
6,080
6,190
6,680
7,030
8,230
9,180

4.126
4.126
4.126
4.126
4.126
4.126
4.126

4,860
4,860
4,860
4,860
4,860
4,860
4,860

7,930
8,510
8,570
8,870
9,080
9,800
10,370

9,970
10,940
11,050
11,540
11,890
13,090
14,040

23.20

L-80
N-80
C-90
T-95
P-110
Q-125

0.478
0.478
0.478
0.478
0.478
0.478

4.044
4.044
4.044
4.044
4.044
4.044

4,010
4,090
4,410
4,650
5,440
6,070

5,350
5,450
5,880
6,200
7,250
8,090

6,690
6,810
7,350
7,750
9,060
10,110

4.044
4.044
4.044
4.044
4.044
4.044

5,540
5,540
5,540
5,540
5,540
5,540

9,550
9,630
9,950
10,190
10,980
11,610

12,230
12,350
12,890
13,290
14,600
15,650

24.10

L-80
N-80
C-90
T-95
P-110
Q-125

0.500
0.500
0.500
0.500
0.500
0.500

4.000
4.000
4.000
4.000
4.000
4.000

4,210
4,290
4,630
4,880
5,700
6,370

5,610
5,720
6,170
6,500
7,600
8,490

7,010
7,150
7,710
8,130
9,500
10,610

4.000
4.000
4.000
4.000
4.000
4.000

5,900
5,900
5,900
5,900
5,900
5,900

10,110
10,190
10,530
10,780
11,600
12,270

12,910
13,050
13,610
14,030
15,400
16,510

MLT Ring Field Make-Up Handbook

Page 15

8-Round LONG Threads

11.60

8-Round LONG Threads

API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)
J-55
K-55
M-65

17.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.304
0.304
0.304
0.304
0.304
0.304
0.304
0.304
0.304

4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892

20.00

M-65
L-80
N-80
C-90
T-95
P-110

0.361
0.361
0.361
0.361
0.361
0.361

23.00

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.415
0.415
0.415
0.415
0.415
0.415
0.415

20.00

J-55
K-55
M-65

0.288 6.049 2,000

0.288 6.049 2,180
0.288 6.049 2,320

24.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.352
0.352
0.352
0.352
0.352
0.352
0.352
0.352

5.921
5.921
5.921
5.921
5.921
5.921
5.921
5.921

2,550
2,790
2,970
3,550
3,610
3,910
4,120
4,810

3,400
3,720
3,960
4,730
4,810
5,210
5,490
6,410

4,250
4,650
4,950
5,910
6,010
6,510
6,860
8,010

28.00

M-65
L-80
N-80
C-90
T-95
P-110

0.417
0.417
0.417
0.417
0.417
0.417

5.791
5.791
5.791
5.791
5.791
5.791

3,620
4,320
4,400
4,760
5,020
5,860

4,830
5,760
5,860
6,350
6,690
7,810

6,040
7,200
7,330
7,940
8,360
9,760

32.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.475
0.475
0.475
0.475
0.475
0.475

5.675
5.675
5.675
5.675
5.675
5.675

5,000 6,660
5,090 6,780
5,510 7,340
5,810 7,740
6,780 9,040
7,580 10,110

8,330
8,480
9,180
9,680
11,300
12,640

Page 16

0.275 4.950 1,630

0.275 4.950 1,790
0.275 4.950 1,900

5 1/2

15.50

2,170 2,710
2,390 2,990
2,530 3,160

4.935
4.935
4.935

2,360 3,990
2,360 4,150
2,360 4,260

5,070
5,350
5,520

1,850
2,040
2,150
2,560
2,610
2,810
2,970
3,470
3,870

2,470
2,720
2,870
3,410
3,480
3,750
3,960
4,620
5,160

3,090
3,400
3,590
4,260
4,350
4,690
4,950
5,780
6,450

4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892

2,870
2,870
2,870
2,870
2,870
2,870
2,870
2,870
2,870

4,720
4,910
5,020
5,430
5,480
5,680
5,840
6,340
6,740

5,960
6,270
6,460
7,130
7,220
7,560
7,820
8,650
9,320

4.778
4.778
4.778
4.778
4.778
4.778

2,650
3,150
3,210
3,470
3,650
4,270

3,530
4,200
4,280
4,620
4,870
5,690

4,410
5,250
5,350
5,780
6,090
7,110

4.778
4.778
4.778
4.778
4.778
4.778

4,040
4,040
4,040
4,040
4,040
4,040

6,690 8,450
7,190 9,290
7,250 9,390
7,510 9,820
7,690 10,130
8,310 11,150

4.670
4.670
4.670
4.670
4.670
4.670
4.670

3,110
3,700
3,770
4,070
4,290
5,010
5,600

4,150
4,930
5,020
5,430
5,720
6,680
7,470

5,190
6,160
6,280
6,790
7,150
8,350
9,340

4.670
4.670
4.670
4.670
4.670
4.670
4.670

5,230
5,230
5,230
5,230
5,230
5,230
5,230

8,340
8,930
9,000
9,300
9,520
10,240
10,830

10,420
11,390
11,510
12,020
12,380
13,580
14,570

6 5/8

2,660 3,330
2,900 3,630
3,090 3,860

MLT Ring Field Make-Up Handbook

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.317
0.317
0.317
0.317
0.317
0.317
0.317

6.366
6.366
6.366
6.366
6.366
6.366
6.366

2,350
2,560
2,730
3,260
3,320
3,590
3,790

3,130
3,410
3,640
4,350
4,420
4,790
5,050

3,910
4,260
4,550
5,440
5,530
5,990
6,310

6.366
6.366
6.366
6.366
6.366
6.366
6.366

4,400
4,400
4,400
4,400
4,400
4,400
4,400

26.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.362
0.362
0.362
0.362
0.362
0.362
0.362
0.362

6.276
6.276
6.276
6.276
6.276
6.276
6.276
6.276

2,750
3,010
3,210
3,830
3,890
4,220
4,450
5,200

3,670
4,010
4,280
5,110
5,190
5,630
5,930
6,930

4,590
5,010
5,350
6,390
6,490
7,040
7,410
8,660

6.276
6.276
6.276
6.276
6.276
6.276
6.276
6.276

6,050
6,050
6,050
6,050
6,050
6,050
6,050
6,050

8,800
9,060
9,370
9,990
10,050
10,380
10,610
11,360

10,640
11,060
11,510
12,550
12,650
13,200
13,570
14,820

29.00

M-65
L-80
N-80
C-90
T-95
P-110

0.408
0.408
0.408
0.408
0.408
0.408

6.184
6.184
6.184
6.184
6.184
6.184

3,690
4,400
4,480
4,860
5,120
5,980

4,920
5,870
5,970
6,480
6,830
7,970

6,150
7,340
7,460
8,100
8,540
9,960

6.184
6.184
6.184
6.184
6.184
6.184

7,900
7,900
7,900
7,900
7,900
7,900

11,590
12,300
12,380
12,760
13,020
13,880

14,050
15,240
15,360
16,000
16,440
17,860

32.00

M-65
L-80
N-80
C-90
T-95
P-110

0.453
0.453
0.453
0.453
0.453
0.453

6.094
6.094
6.094
6.094
6.094
6.094

4,160
4,960
5,040
5,470
5,760
6,730

5,540
6,610
6,720
7,290
7,680
8,970

6,930
8,260
8,400
9,110
9,600
11,210

6.094
6.094
6.094
6.094
6.094
6.094

9,550
9,550
9,550
9,550
9,550
9,550

13,710
14,510
14,590
15,020
15,310
16,280

16,480
17,810
17,950
18,660
19,150
20,760

35.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.498
0.498
0.498
0.498
0.498
0.498

6.004
6.004
6.004
6.004
6.004
6.004

5,510 7,340
5,600 7,460
6,070 8,090
6,400 8,530
7,470 9,960
8,360 11,150

9,180
9,330
10,110
10,660
12,450
13,940

6.004
6.004
6.004
6.004
6.004
6.004

11,150
11,150
11,150
11,150
11,150
11,150

16,660
16,750
17,220
17,550
18,620
19,510

20,330
20,480
21,260
21,810
23,600
25,090

38.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.540
0.540
0.540
0.540
0.540
0.540

5.920
5.920
5.920
5.920
5.920
5.920

6,010 8,010 10,010

6,110 8,140 10,180
6,620 8,830 11,040
6,980 9,310 11,640
8,150 10,870 13,590
9,120 12,160 15,200

5.920
5.920
5.920
5.920
5.920
5.920

12,610
12,610
12,610
12,610
12,610
12,610

18,620
18,720
19,230
19,590
20,760
21,730

22,620
22,790
23,650
24,250
26,200
27,810

26.40

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.328
0.328
0.328
0.328
0.328
0.328
0.328

6.969
6.969
6.969
6.969
6.969
6.969
6.969

2,600
2,830
3,030
3,620
3,680
3,990
4,200

29.70

M-65
L-80
N-80
C-90
T-95
P-110

0.375
0.375
0.375
0.375
0.375
0.375

6.875
6.875
6.875
6.875
6.875
6.875

3,560
4,250
4,310
4,690
4,940
5,770

MLT Ring Field Make-Up Handbook

7 5/8

6,750 8,310
6,960 8,660
7,130 8,950
7,660 9,840
7,720 9,930
7,990 10,390
8,190 10,710

3,460
3,770
4,040
4,820
4,900
5,320
5,600

4,330
4,710
5,050
6,030
6,130
6,650
7,000

6.969
6.969
6.969
6.969
6.969
6.969
6.969

5,490
5,490
5,490
5,490
5,490
5,490
5,490

8,090
8,320
8,520
9,110
9,170
9,480
9,690

9,820
10,200
10,540
11,520
11,620
12,140
12,490

4,740
5,670
5,750
6,250
6,590
7,690

5,930
7,090
7,190
7,810
8,240
9,610

6.875
6.875
6.875
6.875
6.875
6.875

7,670
7,670
7,670
7,670
7,670
7,670

11,230
11,920
11,980
12,360
12,610
13,440

13,600
14,760
14,860
15,480
15,910
17,280

Page 17

8-Round LONG Threads

23.00

8-Round LONG Threads

API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)

7 5/8 (continued)

33.70

M-65
L-80
N-80
C-90
T-95
P-110

0.430
0.430
0.430
0.430
0.430
0.430

6.765
6.765
6.765
6.765
6.765
6.765

4,170
4,980
5,060
5,500
5,790
6,760

6,950
8,300
8,430
9,160
9,650
11,260

6.765
6.765
6.765
6.765
6.765
6.765

9,800
10,150
10,150
10,150
10,150
10,150

13,970
15,130
15,210
15,650
15,940
16,910

17,100
18,450
18,580
19,310
19,800
21,410

39.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.500
0.500
0.500
0.500
0.500
0.500

6.625
6.625
6.625
6.625
6.625
6.625

5,900 7,860 9,830

5,990 7,980 9,980
6,500 8,670 10,840
6,860 9,140 11,430
8,000 10,660 13,330
8,960 11,940 14,930

6.625
6.625
6.625
6.625
6.625
6.625

13,200
13,200
13,200
13,200
13,200
13,200

19,100
19,190
19,700
20,060
21,200
22,160

23,030
23,180
24,040
24,630
26,530
28,130

42.80

L-80
N-80
C-90
T-95
P-110
Q-125

0.562
0.562
0.562
0.562
0.562
0.562

6.501
6.501
6.501
6.501
6.501
6.501

6,680 8,910 11,140

6,800 9,060 11,330
7,380 9,840 12,300
7,780 10,370 12,960
9,080 12,100 15,130
10,160 13,550 16,940

45.30

L-80
N-80
C-90
T-95
P-110
Q-125

0.595
0.595
0.595
0.595
0.595
0.595

6.435
6.435
6.435
6.435
6.435
6.435

7,100
7,220
7,840
8,260
9,640
10,790

9,470
9,620
10,450
11,010
12,850
14,390

11,840
12,030
13,060
13,760
16,060
17,990

47.10

L-80
N-80
C-90
T-95
P-110
Q-125

0.625
0.625
0.625
0.625
0.625
0.625

6.375
6.375
6.375
6.375
6.375
6.375

7,480
7,600
8,250
8,690
10,150
11,360

9,970
10,130
11,000
11,590
13,530
15,150

12,460
12,660
13,750
14,490
16,910
18,940

28.00

H-40
M-65

0.304 8.017 1,960

0.304 8.017 3,050

32.00

J-55
K-55
M-65

0.352 7.921 3,130

0.352 7.921 3,390
0.352 7.921 3,650

4,170 5,210
4,520 5,650
4,870 6,090

36.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.400
0.400
0.400
0.400
0.400
0.400
0.400

7.825
7.825
7.825
7.825
7.825
7.825
7.825

3,650
3,950
4,250
5,090
5,160
5,620
5,920

4,860
5,260
5,670
6,780
6,880
7,490
7,890

6,080
6,580
7,090
8,480
8,600
9,360
9,860

7.825
7.825
7.825
7.825
7.825
7.825
7.825

8,610
9,320
10,050
10,660
10,660
10,660
10,660

12,260
13,270
14,300
15,750
15,820
16,280
16,580

16,320
16,820
17,750
19,140
19,260
20,020
20,520

40.00

M-65
L-80
N-80
C-90
T-95
P-110

0.450
0.450
0.450
0.450
0.450
0.450

7.725
7.725
7.725
7.725
7.725
7.725

4,870 6,490
5,820 7,760
5,910 7,880
6,440 8,580
6,780 9,040
7,910 10,550

8,110
9,700
9,850
10,730
11,300
13,190

7.725
7.725
7.725
7.725
7.725
7.725

11,430
13,570
13,570
13,570
13,570
13,570

16,300
19,390
19,480
20,010
20,350
21,480

21,680
23,270
23,420
24,300
24,870
26,760

44.00

L-80
N-80
C-90
T-95
P-110

0.500
0.500
0.500
0.500
0.500

7.625
7.625
7.625
7.625
7.625

6,560 8,740 10,930

6,650 8,870 11,090
7,240 9,650 12,060
7,630 10,170 12,710
8,900 11,860 14,830

7.625
7.625
7.625
7.625
7.625

15,290
15,500
16,410
16,410
16,410

21,850
22,150
23,650
24,040
25,310

27,340
27,500
28,470
29,120
31,240

Page 18

5,560
6,640
6,740
7,330
7,720
9,010

8 5/8

2,610 3,260
4,060 5,080

7.984
7.984

4,350 6,310 7,610

6,290 9,340 11,370

MLT Ring Field Make-Up Handbook

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)
0.557
0.557
0.557
0.557
0.557
0.557

7.511
7.511
7.511
7.511
7.511
7.511

8 5/8 (continued)

L-80
N-80
C-90
T-95
P-110
Q-125

7,370
7,480
8,140
8,580
10,010
11,220

36.00

J-55
K-55
M-65

0.352 8.921 3,400

0.352 8.921 3,670
0.352 8.921 3,970

40.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.395
0.395
0.395
0.395
0.395
0.395
0.395

8.835
8.835
8.835
8.835
8.835
8.835
8.835

3,900
4,210
4,550
5,450
5,530
6,030
6,350

43.50

M-65
L-80
N-80
C-90
T-95
P-110

0.435
0.435
0.435
0.435
0.435
0.435

8.755
8.755
8.755
8.755
8.755
8.755

47.00

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.472
0.472
0.472
0.472
0.472
0.472
0.472

53.50

L-80
N-80
C-90
T-95
P-110
Q-125

58.40

9,830
9,970
10,850
11,440
13,350
14,960

12,290
12,460
13,560
14,300
16,690
18,700

9 5/8

4,530 5,660
4,890 6,110
5,290 6,610

8.921
8.921
8.921

5,200
5,610
6,070
7,270
7,370
8,040
8,470

6,500
7,010
7,590
9,090
9,210
10,050
10,590

8.835
8.835
8.835
8.835
8.835
8.835
8.835

9,230
9,970
10,750
12,450
12,450
12,450
12,450

13,130
14,180
15,300
17,900
17,980
18,480
18,800

18,620
19,130
20,040
21,540
21,660
22,500
23,040

5,090 6,790
6,100 8,130
6,190 8,250
6,740 8,990
7,110 9,480
8,290 11,050

8,490
10,160
10,310
11,240
11,850
13,810

8.755
8.755
8.755
8.755
8.755
8.755

11,980
14,360
14,570
15,420
15,420
15,420

17,070
20,460
20,760
22,160
22,530
23,710

23,910
25,580
25,730
26,660
27,270
29,230

8.681
8.681
8.681
8.681
8.681
8.681
8.681

5,590 7,450 9,310

6,700 8,930 11,160
6,790 9,050 11,310
7,400 9,870 12,340
7,800 10,400 13,000
9,100 12,130 15,160
10,200 13,600 17,000

8.681
8.681
8.681
8.681
8.681
8.681
8.681

13,110
15,720
15,930
17,360
18,110
18,110
18,110

18,700
22,420
22,720
24,760
25,910
27,210
28,310

27,420
29,270
29,420
30,450
31,110
33,270
35,110

0.545
0.545
0.545
0.545
0.545
0.545

8.535
8.535
8.535
8.535
8.535
8.535

7,850
7,970
8,680
9,150
10,670
11,960

10,470
10,620
11,570
12,200
14,220
15,950

13,090
13,280
14,460
15,250
17,780
19,940

8.535
8.535
8.535
8.535
8.535
8.535

18,250
18,530
20,180
21,280
23,300
23,300

26,100
26,500
28,860
30,430
33,970
35,260

36,390
36,580
37,760
38,550
41,080
43,240

L-80
N-80
C-90
T-95
P-110
Q-125

0.595
0.595
0.595
0.595
0.595
0.595

8.435
8.435
8.435
8.435
8.435
8.435

8,630
8,750
9,540
10,060
11,720
13,160

11,510
11,670
12,720
13,410
15,630
17,540

14,390
14,590
15,900
16,760
19,540
21,930

94.00

H-40
J-55
K-55
M-65

0.438
0.438
0.438
0.438

19.124
19.124
19.124
19.124

6,730
9,070
9,550
11,490

106.50

J-55
K-55

0.500 19.000 10,570

0.500 19.000 11,130

133.00

J-55
K-55
M-65

0.635 18.730 13,800

0.635 18.730 14,530
0.635 18.730 17,490

MLT Ring Field Make-Up Handbook

8,080 11,480 14,860

8,720 12,390 15,310
9,200 13,170 15,810

20

Page 19

8-Round LONG Threads

49.00

 API Casing BUTTRESS Threads

Weight Grade Wall
ID

BUTTRESS Threads

9.50

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(ft-lb)
(in)
(ft-lb)
(ft-lb)

4 1/2

H-40
J-55
K-55

0.205
0.205
0.205

4.090
4.090
4.090

4,500
4,500
4,500

4.020
4.020
4.020

1,750
2,410
2,410

6,250
6,910
6,910

10.50 J-55

K-55

M-65

0.224
0.224
0.224

4.052
4.052
4.052

4,500
4,500
4,500

4.006
4.006
4.006

2,740
2,740
3,180

7,240
7,240
7,680

11.60 J-55

K-55

M-65

L-80

N-80

C-90

T-95

P-110

0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250

4.000
4.000
4.000
4.000
4.000
4.000
4.000
4.000

4,500
4,500
4,500
4,500
4,500
4,500
4,500
4,500

3.970
3.970
3.970
3.970
3.970
3.970
3.970
3.970

3,310
3,310
3,670
3,670
3,670
3,670
3,670
3,670

7,810
7,810
8,170
8,170
8,170
8,170
8,170
8,170

13.50

M-65
L-80
N-80
C-90
T-95
P-110

0.290
0.290
0.290
0.290
0.290
0.290

3.920
3.920
3.920
3.920
3.920
3.920

4,500
4,500
4,500
4,500
4,500
4,500

3.914
3.914
3.914
3.914
3.914
3.914

4,420
4,420
4,420
4,420
4,420
4,420

8,920
8,920
8,920
8,920
8,920
8,920

15.10 P-110

Q-125

0.337
0.337

3.826
3.826

4,500
4,500

3.826
3.826

5,560
5,560

10,060
10,060

11.50 J-55

K-55

M-65

0.220
0.220
0.220

4.560
4.560
4.560

5,000
5,000
5,000

4.518
4.518
4.518

3,140
3,140
3,560

8,140
8,140
8,560

13.00 J-55

K-55

M-65

0.253
0.253
0.253

4.494
4.494
4.494

5,000
5,000
5,000

4.494
4.494
4.494

3,890
3,890
3,890

8,890
8,890
8,890

15.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.296
0.296
0.296
0.296
0.296
0.296
0.296
0.296

4.408
4.408
4.408
4.408
4.408
4.408
4.408
4.408

5,000
5,000
5,000
5,000
5,000
5,000
5,000
5,000

4.408
4.408
4.408
4.408
4.408
4.408
4.408
4.408

5,130
5,130
5,340
5,340
5,340
5,340
5,340
5,340

10,130
10,130
10,340
10,340
10,340
10,340
10,340
10,340

18.00

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.362
0.362
0.362
0.362
0.362
0.362
0.362

4.276
4.276
4.276
4.276
4.276
4.276
4.276

5,000
5,000
5,000
5,000
5,000
5,000
5,000

4.276
4.276
4.276
4.276
4.276
4.276
4.276

7,470
7,470
7,470
7,470
7,470
7,470
7,470

12,470
12,470
12,470
12,470
12,470
12,470
12,470

21.40

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.437
0.437
0.437
0.437
0.437
0.437
0.437

4.126
4.126
4.126
4.126
4.126
4.126
4.126

5,000
5,000
5,000
5,000
5,000
5,000
5,000

4.126
4.126
4.126
4.126
4.126
4.126
4.126

9,770
9,770
9,770
9,770
9,770
9,770
9,770

14,770
14,770
14,770
14,770
14,770
14,770
14,770

Page 20

MLT Ring Field Make-Up Handbook

 API Casing BUTTRESS Threads

MLT
(L-80)
withwith
MLT
RingRing
(L-80)

API
Recommended
Total

Estimated
Total

Torques
Delta
Torque

Torque
Ring Ring Delta
Torque

Weight
Wall
ID
MIN
OPT MAX
ID Torque
Torque MIN MAXMAX
(no rings)
ID
Weight
(lb/ft) Grade Wall
(in)
(in)
(ft-lb)
(in) (ft-lb)
(ft-lb) (ft-lb) (ft-lb)
(ft-lb)
ID
(ft-lb) (ft-lb) (ft-lb)
(in)

5 (continued)

L-80
N-80
C-90
T-95
P-110
Q-125

0.478
0.478
0.478
0.478
0.478
0.478

4.044
4.044
4.044
4.044
4.044
4.044

5,000
5,000
5,000
5,000
5,000
5,000

4.044
4.044
4.044
4.044
4.044
4.044

10,970
10,970
10,970
10,970
10,970
10,970

15,970
15,970
15,970
15,970
15,970
15,970

24.10

L-80
N-80
C-90
T-95
P-110
Q-125

0.500
0.500
0.500
0.500
0.500
0.500

4.000
4.000
4.000
4.000
4.000
4.000

5,000
5,000
5,000
5,000
5,000
5,000

4.000
4.000
4.000
4.000
4.000
4.000

11,600
11,600
11,600
11,600
11,600
11,600

16,600
16,600
16,600
16,600
16,600
16,600

15.50 J-55

K-55

M-65

0.275
0.275
0.275

4.950
4.950
4.950

5,500
5,500
5,500

4.935
4.935
4.935

5,490
5,490
5,870

10,990
10,990
11,370

17.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.304
0.304
0.304
0.304
0.304
0.304
0.304
0.304
0.304

4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892

5,500
5,500
5,500
5,500
5,500
5,500
5,500
5,500
5,500

4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892
4.892

6,430
6,430
6,740
6,740
6,740
6,740
6,740
6,740
6,740

11,930
11,930
12,240
12,240
12,240
12,240
12,240
12,240
12,240

20.00

M-65
L-80
N-80
C-90
T-95
P-110

0.361
0.361
0.361
0.361
0.361
0.361

4.778
4.778
4.778
4.778
4.778
4.778

5,500
5,500
5,500
5,500
5,500
5,500

4.778
4.778
4.778
4.778
4.778
4.778

8,990
8,990
8,990
8,990
8,990
8,990

14,490
14,490
14,490
14,490
14,490
14,490

23.00

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.415
0.415
0.415
0.415
0.415
0.415
0.415

4.670
4.670
4.670
4.670
4.670
4.670
4.670

5,500
5,500
5,500
5,500
5,500
5,500
5,500

4.670
4.670
4.670
4.670
4.670
4.670
4.670

11,050
11,050
11,050
11,050
11,050
11,050
11,050

16,550
16,550
16,550
16,550
16,550
16,550
16,550

20.00 H-40

J-55

K-55

M-65

0.288
0.288
0.288
0.288

6.049
6.049
6.049
6.049

6,630
6,630
6,630
6,630

24.00

0.352
0.352
0.352
0.352
0.352
0.352
0.352
0.352

5.921
5.921
5.921
5.921
5.921
5.921
5.921
5.921

6,630
6,630
6,630
6,630
6,630
6,630
6,630
6,630

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

5 1/2

6 5/8

MLT Ring Field Make-Up Handbook

Page 21

BUTTRESS Threads

23.20

 API Casing BUTTRESS Threads

BUTTRESS Threads

Weight Grade Wall
ID

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(ft-lb)
(in)
(ft-lb)
(ft-lb)

6 5/8 (continued)

28.00

M-65
L-80
N-80
C-90
T-95
P-110

0.417
0.417
0.417
0.417
0.417
0.417

5.791
5.791
5.791
5.791
5.791
5.791

6,630
6,630
6,630
6,630
6,630
6,630

32.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.475
0.475
0.475
0.475
0.475
0.475

5.675
5.675
5.675
5.675
5.675
5.675

6,630
6,630
6,630
6,630
6,630
6,630

20.00 H-40

J-55

K-55

M-65

0.272
0.272
0.272
0.272

6.456
6.456
6.456
6.456

7,000
7,000
7,000
7,000

23.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.317
0.317
0.317
0.317
0.317
0.317
0.317

6.366
6.366
6.366
6.366
6.366
6.366
6.366

26.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.362
0.362
0.362
0.362
0.362
0.362
0.362
0.362

29.00

M-65
L-80
N-80
C-90
T-95
P-110

32.00

6.439
6.439
6.439
6.439

5,950
8,180
8,180
8,670

12,950
15,180
15,180
15,670

7,000
7,000
7,000
7,000
7,000
7,000
7,000

6.366
6.366
6.366
6.366
6.366
6.366
6.366

10,580
10,580
11,120
11,120
11,120
11,120
11,120

17,580
17,580
18,120
18,120
18,120
18,120
18,120

6.276
6.276
6.276
6.276
6.276
6.276
6.276
6.276

7,000
7,000
7,000
7,000
7,000
7,000
7,000
7,000

6.276
6.276
6.276
6.276
6.276
6.276
6.276
6.276

12,930
12,930
14,080
14,080
14,080
14,080
14,080
14,080

19,930
19,930
21,080
21,080
21,080
21,080
21,080
21,080

0.408
0.408
0.408
0.408
0.408
0.408

6.184
6.184
6.184
6.184
6.184
6.184

7,000
7,000
7,000
7,000
7,000
7,000

6.184
6.184
6.184
6.184
6.184
6.184

17,050
17,050
17,050
17,050
17,050
17,050

24,050
24,050
24,050
24,050
24,050
24,050

M-65
L-80
N-80
C-90
T-95
P-110

0.453
0.453
0.453
0.453
0.453
0.453

6.094
6.094
6.094
6.094
6.094
6.094

7,000
7,000
7,000
7,000
7,000
7,000

6.094
6.094
6.094
6.094
6.094
6.094

19,880
19,880
19,880
19,880
19,880
19,880

26,880
26,880
26,880
26,880
26,880
26,880

35.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.498
0.498
0.498
0.498
0.498
0.498

6.004
6.004
6.004
6.004
6.004
6.004

7,000
7,000
7,000
7,000
7,000
7,000

6.004
6.004
6.004
6.004
6.004
6.004

22,640
22,640
22,640
22,640
22,640
22,640

29,640
29,640
29,640
29,640
29,640
29,640

38.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.540
0.540
0.540
0.540
0.540
0.540

5.920
5.920
5.920
5.920
5.920
5.920

7,000
7,000
7,000
7,000
7,000
7,000

5.920
5.920
5.920
5.920
5.920
5.920

25,170
25,170
25,170
25,170
25,170
25,170

32,170
32,170
32,170
32,170
32,170
32,170

Page 22

MLT Ring Field Make-Up Handbook

 API Casing BUTTRESS Threads

Weight Grade Wall
ID

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(ft-lb)
(in)
(ft-lb)
(ft-lb)

7 5/8

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.328
0.328
0.328
0.328
0.328
0.328
0.328

6.969
6.969
6.969
6.969
6.969
6.969
6.969

7,630
7,630
7,630
7,630
7,630
7,630
7,630

6.969
6.969
6.969
6.969
6.969
6.969
6.969

12,890
12,890
13,620
13,620
13,620
13,620
13,620

20,520
20,520
21,250
21,250
21,250
21,250
21,250

29.70

M-65
L-80
N-80
C-90
T-95
P-110

0.375
0.375
0.375
0.375
0.375
0.375

6.875
6.875
6.875
6.875
6.875
6.875

7,630
7,630
7,630
7,630
7,630
7,630

6.875
6.875
6.875
6.875
6.875
6.875

17,310
17,310
17,310
17,310
17,310
17,310

24,940
24,940
24,940
24,940
24,940
24,940

33.70

M-65
L-80
N-80
C-90
T-95
P-110

0.430
0.430
0.430
0.430
0.430
0.430

6.765
6.765
6.765
6.765
6.765
6.765

7,630
7,630
7,630
7,630
7,630
7,630

6.765
6.765
6.765
6.765
6.765
6.765

21,520
21,520
21,520
21,520
21,520
21,520

29,150
29,150
29,150
29,150
29,150
29,150

39.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.500
0.500
0.500
0.500
0.500
0.500

6.625
6.625
6.625
6.625
6.625
6.625

7,630
7,630
7,630
7,630
7,630
7,630

6.625
6.625
6.625
6.625
6.625
6.625

26,730
26,730
26,730
26,730
26,730
26,730

34,360
34,360
34,360
34,360
34,360
34,360

24.00 J-55

K-55

M-65

0.264
0.264
0.264

8.097
8.097
8.097

8,630
8,630
8,630

8.056
8.056
8.056

10,970
10,970
12,610

19,600
19,600
21,240

28.00 H-40

M-65

0.304
0.304

8.017
8.017

8,630
8,630

8.017
8.017

10,400
14,640

19,030
23,270

32.00 H-40

J-55

K-55

M-65

0.352
0.352
0.352
0.352

7.921
7.921
7.921
7.921

8,630
8,630
8,630
8,630

36.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.400
0.400
0.400
0.400
0.400
0.400
0.400

7.825
7.825
7.825
7.825
7.825
7.825
7.825

8,630
8,630
8,630
8,630
8,630
8,630
8,630

7.825
7.825
7.825
7.825
7.825
7.825
7.825

22,030
22,030
22,030
22,030
22,030
22,030
22,030

30,660
30,660
30,660
30,660
30,660
30,660
30,660

40.00

M-65
L-80
N-80
C-90
T-95
P-110

0.450
0.450
0.450
0.450
0.450
0.450

7.725
7.725
7.725
7.725
7.725
7.725

8,630
8,630
8,630
8,630
8,630
8,630

7.725
7.725
7.725
7.725
7.725
7.725

29,340
29,340
29,340
29,340
29,340
29,340

37,970
37,970
37,970
37,970
37,970
37,970

44.00 L-80

N-80

C-90

T-95

P-110

0.500
0.500
0.500
0.500
0.500

7.625
7.625
7.625
7.625
7.625

8,630
8,630
8,630
8,630
8,630

7.625
7.625
7.625
7.625
7.625

34,180
34,180
34,180
34,180
34,180

42,810
42,810
42,810
42,810
42,810

8 5/8

MLT Ring Field Make-Up Handbook

Page 23

BUTTRESS Threads

26.40

 API Casing BUTTRESS Threads

BUTTRESS Threads

Weight Grade Wall
ID

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(ft-lb)
(in)
(ft-lb)
(ft-lb)

9 5/8

36.00 H-40

J-55

K-55

M-65

0.352
0.352
0.352
0.352

8.921
8.921
8.921
8.921

9,630
9,630
9,630
9,630

8.921
8.921
8.921
8.921

16,590
22,800
22,800
24,530

26,220
32,430
32,430
34,160

40.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95

0.395
0.395
0.395
0.395
0.395
0.395
0.395

8.835
8.835
8.835
8.835
8.835
8.835
8.835

9,630
9,630
9,630
9,630
9,630
9,630
9,630

8.835
8.835
8.835
8.835
8.835
8.835
8.8358.835

27,130
27,130
29,990
29,990
29,990
29,990
29,990

36,760
36,760
39,620
39,620
39,620
39,620
39,620

43.50

M-65
L-80
N-80
C-90
T-95
P-110

0.435
0.435
0.435
0.435
0.435
0.435

8.755
8.755
8.755
8.755
8.755
8.755

9,630
9,630
9,630
9,630
9,630
9,630

8.755
8.755
8.755
8.755
8.755
8.755

33,580
35,000
35,000
35,000
35,000
35,000

43,210
44,630
44,630
44,630
44,630
44,630

47.00

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.472
0.472
0.472
0.472
0.472
0.472
0.472

8.681
8.681
8.681
8.681
8.681
8.681
8.681

9,630
9,630
9,630
9,630
9,630
9,630
9,630

8.681
8.681
8.681
8.681
8.681
8.681
8.681

39,560
39,560
39,560
39,560
39,560
39,560
39,560

49,190
49,190
49,190
49,190
49,190
49,190
49,190

53.50

L-80
N-80
C-90
T-95
P-110
Q-125

0.545
0.545
0.545
0.545
0.545
0.545

8.535
8.535
8.535
8.535
8.535
8.535

9,630
9,630
9,630
9,630
9,630
9,630

8.535
8.535
8.535
8.535
8.535
8.535

48,390
48,390
48,390
48,390
48,390
48,390

58,020
58,020
58,020
58,020
58,020
58,020

40.50 H-40

J-55

K-55

M-65

0.350
0.350
0.350
0.350

10.050
10.050
10.050
10.050

10,750
10,750
10,750
10,750

10.050
10.050
10.050
10.050

20,620
28,350
28,350
30,460

31,370
39,100
39,100
41,210

45.50 J-55

K-55

M-65

0.400
0.400
0.400

9.950
9.950
9.950

10,750
10,750
10,750

9.950
9.950
9.950

34,690
34,690
38,460

45,440
45,440
49,210

51.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.450
0.450
0.450
0.450
0.450
0.450
0.450
0.450

9.850
9.850
9.850
9.850
9.850
9.850
9.850
9.850

10,750
10,750
10,750
10,750
10,750
10,750
10,750
10,750

9.850
9.850
9.850
9.850
9.850
9.850
9.850
9.850

40,930
40,930
46,330
46,330
46,330
46,330
46,330
46,330

51,680
51,680
57,080
57,080
57,080
57,080
57,080
57,080

55.50

M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.495
0.495
0.495
0.495
0.495
0.495
0.495

9.760
9.760
9.760
9.760
9.760
9.760
9.760

10,750
10,750
10,750
10,750
10,750
10,750
10,750

9.760
9.760
9.760
9.760
9.760
9.760
9.760

53,310
53,310
53,310
53,310
53,310
53,310
53,310

64,060
64,060
64,060
64,060
64,060
64,060
64,060

Page 24

10 3/4

MLT Ring Field Make-Up Handbook

 API Casing BUTTRESS Threads

Weight Grade Wall
ID

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(ft-lb)
(in)
(ft-lb)
(ft-lb)

10 3/4

0.545
0.545
0.545
0.545

9.660
9.660
9.660
9.660

10,750
10,750
10,750
10,750

9.660
9.660
9.660
9.660

60,940
60,940
60,940
60,940

71,690
71,690
71,690
71,690

47.00 J-55

K-55

M-65

0.375 11.000
0.375 11.000
0.375 11.000

11,750
11,750
11,750

11.000
11.000
11.000

37,830
37,830
41,370

49,580
49,580
53,120

54.00 J-55

K-55

M-65

0.435 10.880
0.435 10.880
0.435 10.880

11,750
11,750
11,750

10.880
10.880
10.880

46,910
46,910
52,830

58,660
58,660
64,580

60.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110
Q-125

0.489
0.489
0.489
0.489
0.489
0.489
0.489
0.489
0.489

10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772

11,750
11,750
11,750
11,750
11,750
11,750
11,750
11,750
11,750

10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772
10.772

54,950
54,950
62,970
62,970
62,970
62,970
62,970
62,970
62,970

66,700
66,700
74,720
74,720
74,720
74,720
74,720
74,720
74,720

65.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.534
0.534
0.534
0.534
0.534
0.534

10.682
10.682
10.682
10.682
10.682
10.682

11,750
11,750
11,750
11,750
11,750
11,750

10.682
10.682
10.682
10.682
10.682
10.682

71,300
71,300
71,300
71,300
71,300
71,300

83,050
83,050
83,050
83,050
83,050
83,050

54.50 J-55

K-55

M-65

0.380 12.615
0.380 12.615
0.380 12.615

13,380
13,380
13,380

12.575
12.575
12.575

50,250
50,250
59,380

63,630
63,630
72,760

61.00 J-55

K-55

M-65

0.430 12.515
0.430 12.515
0.430 12.515

13,380
13,380
13,380

12.575
12.575
12.575

60,210
60,210
60,210

73,590
73,590
73,590

68.00

J-55
K-55
M-65
L-80
N-80
C-90
T-95
P-110

0.480
0.480
0.480
0.480
0.480
0.480
0.480
0.480

12.415
12.415
12.415
12.415
12.415
12.415
12.415
12.415

13,380
13,380
13,380
13,380
13,380
13,380
13,380
13,380

12.575
12.575
12.575
12.575
12.575
12.575
12.575
12.575

60,210
60,210
60,210
60,210
60,210
60,210
60,210
60,210

73,590
73,590
73,590
73,590
73,590
73,590
73,590
73,590

72.00

L-80
N-80
C-90
T-95
P-110
Q-125

0.514
0.514
0.514
0.514
0.514
0.514

12.347
12.347
12.347
12.347
12.347
12.347

13,380
13,380
13,380
13,380
13,380
13,380

12.575
12.575
12.575
12.575
12.575
12.575

60,210
60,210
60,210
60,210
60,210
60,210

73,590
73,590
73,590
73,590
73,590
73,590

11 3/4

13 3/8

MLT Ring Field Make-Up Handbook

Page 25

BUTTRESS Threads

60.70 C-90

T-95

P-110

Q-125

API Tubing EUE 8-Round Thread

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

60.32 mm

6.99
H-40
4.83 50.67 1,000 1,340 1,680 52.45
760 1,760

J-55 1,320 1,750 2,180
840 2,160

L-80 1,790 2,390 2,980
840 2,630

N-80 1,830 2,440 3,050
840 2,670

C-90 1,950 2,600 3,250
840 2,790

T-95 2,060 2,750 3,440
840 2,900
P-110 2,430 3,230 4,040
840 3,270

8.85
L-80
6.45 47.42 2,220 2,970 3,710 49.71 1,150 3,380

N-80 2,280 3,040 3,800 1,150 3,430

C-90 2,430 3,240 4,050 1,150 3,580

T-95 2,560 3,420 4,270 1,150 3,710
P-110 3,000 4,000 5,000 1,150 4,150

EUE 8-Round Thread (METRIC)

73.02 mm

9.67
H-40
5.51 62.00 1,270 1,690 2,120 64.03 1,220 2,490

J-55 1,680 2,240 2,790 1,370 3,050

L-80 2,290 3,050 3,810 1,370 3,660

N-80 2,350 3,120 3,900 1,370 3,710

C-90 2,510 3,340 4,180 1,370 3,880

T-95 2,640 3,530 4,410 1,370 4,010
P-110 3,090 4,120 5,150 1,370 4,460

11.76
L-80
7.01 59.00 2,750 3,670 4,600 61.29 1,830

N-80 2,820 3,760 4,690 1,830 4,650

C-90 3,020 4,030 5,030 1,830 4,850

T-95 3,170 4,230 5,290 1,830 5,000
P-110 3,730 4,960 6,210 1,830 5,560

12.95
L-80
7.82 57.38 3,000 4,000 5,000 59.66 2,090 5,080

N-80 3,080 4,090 5,120 2,090 5,170

C-90 3,280 4,380 5,480 2,090 5,370

T-95 3,460 4,610 5,760 2,090 5,550
P-110 4,050 5,400 6,750 2,090 6,140

88.90 mm

13.84
H-40
6.45 76.00 1,760 2,350 2,930 78.38 2,180 3,950

J-55 2,320 3,090 3,860 2,560 4,880

L-80 3,080 4,110 5,140 2,560 5,640

N-80 3,250 4,340 5,420 2,560 5,820

C-90 3,480 4,650 5,820 2,560 6,050

T-95 3,690 4,910 6,140 2,560 6,250
P-110 4,300 5,740 7,170 2,560 6,860

19.27
L-80
9.53 69.85 4,270 5,690 7,120 72.14 4,070 8,340

N-80 4,370 5,820 7,270 4,070 8,430

C-90 4,690 6,250 7,810 4,070 8,760

T-95 4,940 6,580 8,220 4,070 9,000
P-110 5,780 7,700 9,630 4,070 9,840

Page 26

2,440
3,020
3,820
3,890
4,090
4,280
4,880
4,870
4,950
5,210
5,420
6,160

3,340
4,160
5,180
5,270
5,550
5,780
6,520
6,430
6,520
6,860
7,120
8,040
7,090
7,210
7,570
7,850
8,840

5,110
6,430
7,700
7,990
8,380
8,700
9,730
11,190
11,330
11,880
12,280
13,690

MLT Ring Field Make-Up Handbook

 API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

114.30 mm

14.14 H-40
5.21 103.89
790 1,040 1,300

J-55 1,030 1,370 1,710
K-55 1,140 1,520 1,900

15.63
J-55
5.69 102.92 1,340 1,790 2,240
K-55 1,490 1,980 2,480
M-65 1,570 2,090 2,620

17.26
J-55
6.35 101.60 1,570 2,090 2,620 100.84 2,160 3,730
K-55 1,740 2,300 2,890 100.84 2,160 3,890

4,770
5,040

127.00 mm

5,530
5,830
6,130
7,010
7,360

139.70 mm

20.83 H-40
6.20 127.30 1,330 1,760 2,210

J-55 1,750 2,330 2,910
K-55 1,930 2,560 3,200

23.07
J-55
6.98 125.73 2,060 2,740 3,430 125.73 3,440 5,500
K-55 2,260 3,010 3,770 3,440 5,710
M-65 2,390 3,190 3,990 3,440 5,830

25.30
J-55
7.72 124.26 2,330 3,100 3,880 124.26 4,390 6,720
K-55 2,560 3,420 4,270 4,390 6,960

6,870
7,210
7,430
8,270
8,660

168.28 mm

29.76 H-40
7.32 153.64 1,870 2,490 3,120

J-55 2,490 3,320 4,150
K-55 2,710 3,620 4,530
M-65 2,900 3,860 4,830

35.72
J-55
8.94 150.39 3,200 4,260 5,330
K-55 3,480 4,640 5,800

177.80 mm

25.30 H-40
5.87 166.07 1,250 1,650 2,070


29.76 H-40
6.91 163.98 1,790 2,390 2,980

J-55 2,390 3,170 3,970
K-55 2,590 3,440 4,310
M-65 2,780 3,700 4,620

34.23
J-55
8.05 161.70 2,890 3,850 4,810 161.70 6,870 9,760
K-55 3,150 4,190 5,230 7,480 10,630

38.69
J-55
9.19 159.41 3,400 4,530 5,670 159.41 8,070 11,470
K-55 3,700 4,940 6,170 8,770 12,470

MLT Ring Field Make-Up Handbook

12,360
12,790
15,140
15,650
Page 27

8-Round SHORT Threads (METRIC)

17.11
J-55
5.59 115.82 1,360 1,800 2,250
K-55 1,490 1,990 2,490
M-65 1,570 2,100 2,630

19.35
J-55
6.43 114.15 1,720 2,290 2,860 113.28 2,670 4,390
K-55 1,900 2,520 3,160 113.28 2,670 4,570
M-65 1,990 2,660 3,320 113.28 2,810 4,800

22.32
J-55
7.52 111.96 2,100 2,810 3,510 111.96 3,500 5,600
K-55 2,320 3,090 3,860 3,500 5,820

 API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

193.68 mm

35.72 H-40
7.62 178.44 2,160 2,870 3,590

39.29
J-55
8.33 177.01 3,200 4,270 5,340 177.01 7,610 10,810 14,660
K-55 3,480 4,640 5,800 8,280 11,770 15,120
M-65 3,740 4,990 6,240 8,910 12,650 15,560

8-Round SHORT Threads (METRIC)

219.08 mm

35.72
J-55
6.71 205.66 2,480 3,310 4,140
K-55 2,670 3,570 4,460
M-65 2,900 3,860 4,830

41.67 H-40
7.72 203.63 2,370 3,160 3,950 203.63 5,650 8,030
M-65 3,690 4,910 6,140 8,800 12,490

47.62 H-40
8.94 201.19 2,830 3,780 4,730

J-55 3,780 5,040 6,300
K-55 4,090 5,450 6,820
M-65 4,420 5,900 7,380

53.57
J-55 10.16 198.76 4,420 5,880 7,360 198.76 10,440 14,860
K-55 4,760 6,350 7,930 11,240 16,000
M-65 5,150 6,860 8,580 12,160 17,310

11,350
15,850

23,750
24,320
26,150

244.48 mm

48.07 H-40
7.92 228.63 2,590 3,440 4,310

53.57 H-40
8.94 226.59 3,000 3,990 4,990 226.59 7,120 10,110

J-55 4,010 5,340 6,680 9,520 13,530
K-55 4,300 5,740 7,170 10,200 14,490
M-65 4,680 6,240 7,800 11,100 15,780

59.53
J-55 10.03 224.41 4,600 6,130 7,660 224.41 10,860 15,460
K-55 4,950 6,590 8,240 11,690 16,640
M-65 5,370 7,160 8,950 12,690 18,060

16,840
22,550
23,900
24,990
25,760
27,730
30,100

273.05 mm

48.74 H-40
7.09 258.88 2,090 2,780 3,470

60.27 H-40
8.89 255.27 3,200 4,260 5,330 255.27 7,610 10,810

J-55 4,270 5,690 7,120 10,140 14,410
K-55 4,580 6,100 7,630 10,890 15,470
M-65 4,990 6,660 8,320 11,850 16,840

67.71
J-55 10.16 252.73 5,020 6,680 8,350 252.73 11,860 16,880
K-55 5,370 7,160 8,950 12,700 18,070
M-65 5,860 7,810 9,760 13,840 19,700

75.90
J-55 11.43 250.19 5,750 7,660 9,570 250.19 13,540 19,290
K-55 6,170 8,220 10,280 14,530 20,700
M-65 6,720 8,960 11,200 15,820 22,550

L-80 8,080 10,770 13,460 19,010 27,090
N-80 8,180 10,900 13,630 19,240 27,410
C-90 8,930 11,920 14,900 21,030 29,960

T-95 9,420 12,570 15,710 22,170 31,590
P-110 10,970 14,630 18,290 25,810 36,780

Page 28

18,010
24,020
25,770
28,110
28,110
30,130
32,840
32,120
34,490
37,560
45,130
45,690
48,520
49,340
51,910

MLT Ring Field Make-Up Handbook

 API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

273.05 mm (continued)

82.59 M-65 12.57 247.90 7,480 9,980 12,470 247.90 17,540 25,030

L-80 8,990 11,990 14,980 21,070 30,060
N-80 9,100 12,130 15,170 21,330 30,420
C-90 9,950 13,270 16,590 23,330 33,280

T-95 10,490 13,990 17,490 24,610 35,100
P-110 12,230 16,300 20,380 28,680 40,900
Q-125 13,730 18,300 22,890 32,200 45,930

90.33 C-90 13.84 245.36 11,080 14,760 18,450 245.36 25,840 36,920

T-95 11,670 15,560 19,460 27,240 38,910
P-110 13,600 18,130 22,660 31,730 45,320
Q-125 15,280 20,360 25,460 35,640 50,920

97.77 C-90 15.11 242.82 12,190 16,240 20,310

T-95 12,840 17,120 21,410
P-110 14,950 19,940 24,930
Q-125 16,800 22,400 28,000

41,720
50,110
50,730
55,510
56,710
59,600
62,110
61,500
64,780
67,980
70,790

27,250
29,080
31,810
32,350
34,530
37,810
36,820
39,320
43,090
51,810
52,440
57,390
60,520
67,420
70,010
57,000
57,680
63,150
66,600
76,280
79,140

339.73 mm

71.43 H-40
8.38 322.96 3,280 4,370 5,460

81.10
J-55
9.65 320.42 5,230 6,970 8,720 319.41 12,390 17,630
K-55 5,560 7,420 9,270 319.41 13,160 18,720
M-65 6,130 8,160 10,210 319.41 14,520 20,650

90.78
J-55 10.92 317.88 6,050 8,070 10,090 319.41 14,330 20,380
K-55 6,440 8,580 10,720 15,250 21,690
M-65 7,090 9,450 11,810 16,800 23,890

MLT Ring Field Make-Up Handbook

29,370
31,240
34,400
33,990
36,130
39,780

Page 29

8-Round SHORT Threads (METRIC)

298.45 mm

62.50 H-40
8.46 281.53 3,120 4,160 5,210

69.94
J-55
9.53 279.40 4,850 6,470 8,080 279.40 11,520 16,380
K-55 5,180 6,900 8,620 12,280 17,460
M-65 5,670 7,550 9,440 13,440 19,100

80.36
J-55 11.05 276.35 5,780 7,700 9,630 276.35 13,630 19,400
K-55 6,170 8,220 10,280 14,560 20,730
M-65 6,750 9,000 11,250 15,930 22,680

89.29
J-55 12.42 273.61 6,600 8,800 11,000 273.61 15,510 22,110
K-55 7,050 9,400 11,740 16,550 23,600
M-65 7,710 10,290 12,870 18,130 25,840

L-80 9,290 12,380 15,470 21,810 31,100
N-80 9,400 12,530 15,660 22,070 31,470
C-90 10,280 13,710 17,140 24,130 34,410

T-95 10,850 14,450 18,070 25,480 36,320
P-110 12,640 16,840 21,060 29,680 42,310
Q-125 14,180 18,910 23,650 33,310 47,490

96.73
L-80 13.56 271.32 10,240 13,650 17,070 271.32 23,940 34,180
N-80 10,360 13,820 17,270 24,230 34,590
C-90 11,350 15,130 18,910 26,550 37,890

T-95 11,970 15,960 19,940 28,000 39,970
P-110 13,940 18,570 23,220 32,590 46,530
Q-125 15,650 20,870 26,090 36,590 52,240

 API Casing 8-Round SHORT Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

339.73 mm (continued)

101.19
J-55 12.19 315.34 6,860 9,150 11,440 319.41 16,260
K-55 7,310 9,730 12,180 17,310
M-65 8,040 10,720 13,410 19,050

L-80 9,680 12,910 16,130 22,930
N-80 9,790 13,060 16,320 23,180
C-90 10,750 14,330 17,910 25,480

T-95 11,330 15,100 18,890 26,840
P-110 13,190 17,580 21,980 31,250

107.15
L-80 13.06 313.61 10,470 13,950 17,440 319.41 24,800
N-80 10,580 14,100 17,630 25,060
C-90 11,620 15,480 19,360 27,520

T-95 12,240 16,320 20,400 29,000
P-110 14,250 18,990 23,740 33,760
Q-125 16,030 21,370 26,710 37,960

23,120
24,620
27,090
32,610
32,970
36,230
38,180
44,440

38,550
41,010
45,180
54,350
54,990
60,330
61,800
64,890

35,260
35,630
39,140
41,240
48,010
53,990

58,750
59,380
62,270
63,320
66,650
69,620

8-Round SHORT Threads (METRIC)

406.40 mm

96.73 H-40
9.53 387.35 5,950

116.61
J-55 11.13 384.15 9,630
K-55 10,200
M-65 11,280

125.01
J-55 12.57 381.25 11,080
K-55 11,730
M-65 12,980

130.21 H-40 11.05 450.98

J-55
K-55
M-65

473.10 mm

7,580
10,220
10,770
11,990

508.00 mm

139.89 H-40 11.13 485.75 7,880

J-55 10,630
K-55 11,170
M-65 12,460

158.49
J-55 12.70 482.60 12,380
K-55 13,020

197.93
J-55 16.13 475.74 16,160
K-55 16,990
M-65 18,950

Page 30

MLT Ring Field Make-Up Handbook

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

114.30 mm

17.26
J-55
6.35 101.60 1,650 2,200 2,750 100.64 2,060 3,710 4,810

K-55 1,830 2,440 3,050 2,060 3,890 5,110
M-65 1,910 2,550 3,190 2,100 4,010 5,290

L-80 2,260 3,020 3,780 2,100 4,370 5,880

N-80 2,320 3,090 3,860 2,100 4,420 5,970

C-90 2,490 3,320 4,150 2,100 4,600 6,250

T-95 2,630 3,500 4,380 2,100 4,730 6,480
P-110 3,080 4,090 5,120 2,100 5,180 7,230

20.09 M-65
7.37 99.57 2,320 3,090 3,860 99.42 2,540 4,850 6,400

L-80 2,750 3,670 4,600 2,540 5,290 7,130

N-80 2,810 3,740 4,680 2,540 5,340 7,210

C-90 3,020 4,030 5,030 2,540 5,560 7,570

T-95 3,190 4,240 5,300 2,540 5,720 7,840
P-110 3,730 4,960 6,210 2,540 6,260 8,740

22.47 P-110
8.56 97.18 4,470 5,970 7,460 97.18 3,440 7,920 10,900
Q-125 4,990 6,660 8,320 3,440 8,430 11,770

MLT Ring Field Make-Up Handbook

4,220
4,410
4,940

5,450
5,760
6,370

5,380 6,900
5,630 7,290
5,750 7,510
6,250 8,340
6,320 8,450
6,560 8,850
6,740 9,150
7,360 10,180
8,160
8,800
8,870
9,180
9,420
10,200
10,830

10,410
11,460
11,580
12,110
12,500
13,800
14,850

10,750
11,540
11,620
12,030
12,310
13,290
14,060

13,520
14,830
14,980
15,650
16,120
17,750
19,040

12,950
13,060
13,490
13,820
14,890
15,740

16,580
16,740
17,480
18,020
19,790
21,220

13,710
13,820
14,280
14,620
15,730
16,640

17,500
17,690
18,450
19,020
20,880
22,380
Page 31

8-Round LONG Threads (METRIC)

127.00 mm

19.35
J-55
6.43 114.15 1,860 2,470 3,090 112.62 2,360

K-55 2,050 2,730 3,400 2,360
M-65 2,160 2,870 3,590 2,780

22.32
J-55
7.52 111.96 2,260 3,020 3,780 111.96 3,120

K-55 2,510 3,340 4,180 3,120
M-65 2,630 3,510 4,390 3,120

L-80 3,130 4,180 5,220 3,120

N-80 3,200 4,260 5,330 3,120

C-90 3,440 4,580 5,740 3,120

T-95 3,620 4,830 6,030 3,120
P-110 4,240 5,650 7,060 3,120

26.79 M-65
9.19 108.61 3,360 4,490 5,610 108.61 4,800

L-80 4,000 5,330 6,660 4,800

N-80 4,070 5,420 6,780 4,800

C-90 4,380 5,840 7,310 4,800

T-95 4,620 6,170 7,700 4,800
P-110 5,400 7,200 9,000 4,800
Q-125 6,030 8,040 10,050 4,800

31.85 M-65 11.10 104.80 4,160 5,550 6,930 104.80 6,590

L-80 4,950 6,590 8,240 6,590

N-80 5,030 6,710 8,390 6,590

C-90 5,440 7,240 9,060 6,590

T-95 5,720 7,620 9,530 6,590
P-110 6,700 8,920 11,160 6,590
Q-125 7,470 9,950 12,450 6,590

34.53
L-80 12.14 102.72 5,440 7,250 9,070 102.72 7,510

N-80 5,550 7,390 9,230 7,510

C-90 5,980 7,970 9,970 7,510

T-95 6,300 8,410 10,510 7,510
P-110 7,380 9,830 12,280 7,510
Q-125 8,230 10,970 13,710 7,510

35.86
L-80 12.70 101.60 5,710 7,610 9,500 101.60 8,000

N-80 5,820 7,760 9,690 8,000

C-90 6,280 8,370 10,450 8,000

T-95 6,620 8,810 11,020 8,000
P-110 7,730 10,300 12,880 8,000
Q-125 8,640 11,510 14,390 8,000

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

8-Round LONG Threads (METRIC)

139.70 mm

23.07
J-55
6.98 125.73 2,210 2,940 3,670 125.35 3,200

K-55 2,430 3,240 4,050 3,200
M-65 2,580 3,430 4,280 3,200

25.30
J-55
7.72 124.26 2,510 3,350 4,190 124.26 3,890

K-55 2,770 3,690 4,610 3,890
M-65 2,910 3,890 4,870 3,890

L-80 3,470 4,620 5,780 3,890

N-80 3,540 4,720 5,900 3,890

C-90 3,810 5,080 6,360 3,890

T-95 4,030 5,370 6,710 3,890
P-110 4,700 6,260 7,840 3,890
Q-125 5,250 7,000 8,740 3,890

29.76 M-65
9.17 121.36 3,590 4,790 5,980 121.36 5,480

L-80 4,270 5,690 7,120 5,480

N-80 4,350 5,800 7,250 5,480

C-90 4,700 6,260 7,840 5,480

T-95 4,950 6,600 8,260 5,480
P-110 5,790 7,710 9,640 5,480

34.23 M-65 10.54 118.62 4,220 5,630 7,040 118.62 7,090

L-80 5,020 6,680 8,350 7,090

N-80 5,110 6,810 8,510 7,090

C-90 5,520 7,360 9,210 7,090

T-95 5,820 7,760 9,690 7,090
P-110 6,790 9,060 11,320 7,090
Q-125 7,590 10,130 12,660 7,090

5,410
5,630
5,780

6,870
7,250
7,480

6,400
6,660
6,810
7,360
7,430
7,700
7,920
8,600
9,140

8,080
8,500
8,760
9,670
9,790
10,250
10,600
11,730
12,640

9,070
9,750
9,830
10,180
10,430
11,270

11,460
12,600
12,730
13,310
13,730
15,120

11,310
12,110
12,200
12,610
12,910
13,880
14,680

14,130
15,440
15,610
16,300
16,780
18,410
19,750

168.28 mm

29.76
J-55
7.32 153.64 2,710 3,610 4,510

K-55 2,960 3,930 4,920
M-65 3,150 4,190 5,230

35.72
J-55
8.94 150.39 3,460 4,610 5,760

K-55 3,780 5,040 6,300
M-65 4,030 5,370 6,710

L-80 4,810 6,410 8,010

N-80 4,890 6,520 8,150

C-90 5,300 7,060 8,830

T-95 5,590 7,440 9,300
P-110 6,520 8,690 10,860

41.67 M-65 10.59 147.09 4,910 6,550 8,190

L-80 5,860 7,810 9,760

N-80 5,970 7,940 9,940

C-90 6,450 8,610 10,770

T-95 6,810 9,070 11,330
P-110 7,940 10,590 13,230

47.62
L-80 12.06 144.15 6,780 9,030 11,290

N-80 6,900 9,190 11,500

C-90 7,470 9,950 12,450

T-95 7,880 10,490 13,120
P-110 9,190 12,260 15,320
Q-125 10,280 13,710 17,140
34.23



Page 32

J-55
8.05 161.70
K-55
M-65
L-80

177.80 mm

3,190
3,470
3,700
4,420

4,240
4,620
4,940
5,900

5,300 161.70
5,780
6,170
7,380

5,970
5,970
5,970
5,970

9,150
9,440
9,670
10,390

11,270
11,740
12,130
13,340

MLT Ring Field Make-Up Handbook

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

177.80 mm (continued)

193.68 mm

39.29
J-55
8.33 177.01 3,530 4,690 5,870 177.01 7,440

K-55 3,840 5,110 6,390 7,440
M-65 4,110 5,480 6,850 7,440

L-80 4,910 6,530 8,180 7,440

N-80 4,990 6,640 8,310 7,440

C-90 5,410 7,210 9,020 7,440

T-95 5,690 7,590 9,490 7,440

44.20 M-65
9.52 174.63 4,830 6,430 8,040 174.63 10,400

L-80 5,760 7,690 9,610 10,400

N-80 5,840 7,800 9,750 10,400

C-90 6,360 8,470 10,590 10,400

T-95 6,700 8,930 11,170 10,400
P-110 7,820 10,430 13,030 10,400

50.15 M-65 10.92 171.83 5,650 7,540 9,420 171.83 13,290

L-80 6,750 9,000 11,250 13,760

N-80 6,860 9,140 11,430 13,760

C-90 7,460 9,940 12,420 13,760

T-95 7,850 10,470 13,080 13,760
P-110 9,170 12,220 15,270 13,760
MLT Ring Field Make-Up Handbook

13,460
14,090
14,520
14,430
15,000
15,610
17,020
17,150
17,900
18,400
20,090
19,050
20,660
20,830
21,690
22,290
24,210
22,340
24,150
24,340
25,300
25,960
28,150
27,560
27,770
28,820
29,570
32,000
34,020
30,670
30,900
32,060
32,880
35,520
37,700

10,970
11,280
11,550
12,350
12,430
12,850
13,140

13,310
13,830
14,290
15,620
15,750
16,460
16,930

15,230
16,160
16,240
16,760
17,100
18,220

18,440
20,010
20,150
20,990
21,570
23,430

18,940
20,510
20,620
21,220
21,610
22,930

23,180
25,010
25,190
26,180
26,840
29,030
Page 33

8-Round LONG Threads (METRIC)

N-80
8.05 161.70 4,500 5,990 7,500 161.70 5,970 10,470

C-90 4,870 6,490 8,120 5,970 10,830

T-95 5,140 6,850 8,560 5,970 11,100

38.69
J-55
9.19 159.41 3,730 4,980 6,220 159.41 8,200 11,930

K-55 4,080 5,440 6,790 8,200 12,280
M-65 4,350 5,800 7,250 8,350 12,700

L-80 5,190 6,930 8,660 8,350 13,540

N-80 5,270 7,040 8,800 8,350 13,630

C-90 5,720 7,630 9,540 8,350 14,070

T-95 6,030 8,040 10,050 8,350 14,390
P-110 7,050 9,400 11,740 8,350 15,400

43.16 M-65 10.36 157.07 5,000 6,670 8,340 157.07 10,710 15,710

L-80 5,970 7,960 9,950 10,710 16,680

N-80 6,070 8,090 10,110 10,710 16,780

C-90 6,590 8,790 10,980 10,710 17,300

T-95 6,940 9,260 11,580 10,710 17,650
P-110 8,110 10,810 13,500 10,710 18,820

47.62 M-65 11.51 154.79 5,640 7,510 9,400 154.79 12,950 18,590

L-80 6,720 8,960 11,200 12,950 19,670

N-80 6,830 9,110 11,390 12,950 19,780

C-90 7,420 9,880 12,350 12,950 20,360

T-95 7,810 10,410 13,020 12,950 20,760
P-110 9,120 12,160 15,200 12,950 22,070

52.09
L-80 12.65 152.50 7,470 9,950 12,450 152.50 15,120 22,590

N-80 7,590 10,110 12,650 15,120 22,710

C-90 8,230 10,970 13,710 15,120 23,350

T-95 8,680 11,560 14,450 15,120 23,790
P-110 10,130 13,500 16,880 15,120 25,240
Q-125 11,330 15,120 18,900 15,120 26,450

56.55
L-80 13.72 150.37 8,150 10,860 13,570 150.37 17,100 25,240

N-80 8,280 11,040 13,800 17,100 25,380

C-90 8,980 11,970 14,970 17,100 26,070

T-95 9,460 12,620 15,780 17,100 26,560
P-110 11,050 14,740 18,430 17,100 28,150
Q-125 12,360 16,490 20,610 17,100 29,460

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

8-Round LONG Threads (METRIC)

193.68 mm (continued)

58.04
L-80 12.70 168.28 8,000 10,660 13,330 168.28 17,900 25,900

N-80 8,120 10,820 13,530 168.28 17,900 26,020

C-90 8,810 11,750 14,700 168.28 17,900 26,710

T-95 9,300 12,390 15,500 168.28 17,900 27,200
P-110 10,850 14,450 18,070 168.28 17,900 28,740
Q-125 12,150 16,190 20,240 168.28 17,900 30,040

63.69
L-80 14.27 165.13 9,060 12,080 15,100

N-80 9,220 12,280 15,360

C-90 10,010 13,340 16,680

T-95 10,550 14,060 17,570
P-110 12,310 16,410 20,510
Q-125 13,770 18,370 22,970

67.41
L-80 15.11 163.45 9,630 12,840 16,050

N-80 9,790 13,040 16,310

C-90 10,630 14,170 17,710

T-95 11,200 14,930 18,660
P-110 13,070 17,420 21,770
Q-125 14,630 19,510 24,390

70.09
L-80 15.88 161.93 10,140 13,520 16,890

N-80 10,300 13,730 17,160

C-90 11,190 14,910 18,640

T-95 11,780 15,710 19,650
P-110 13,760 18,340 22,930
Q-125 15,400 20,540 25,680

219.08 mm

41.67
H-40
7.72 203.63 2,660 3,540 4,420 202.79 5,900 8,560
M-65 4,140 5,500 6,890 8,530 12,660

47.62
J-55
8.94 201.19 4,240 5,650 7,060

K-55 4,600 6,130 7,660
M-65 4,950 6,600 8,260

53.57
J-55 10.16 198.76 4,950 6,590 8,240 198.76 11,670 16,620

K-55 5,360 7,130 8,920 12,640 17,990
M-65 5,760 7,690 9,610 13,630 19,390

L-80 6,900 9,190 11,500 14,450 21,350

N-80 7,000 9,330 11,660 14,450 21,450

C-90 7,620 10,150 12,690 14,450 22,070

T-95 8,030 10,700 13,370 14,450 22,480

59.53 M-65 11.43 196.22 6,600 8,800 11,000 196.22 15,500 22,100

L-80 7,890 10,520 13,150 18,400 26,290

N-80 8,010 10,680 13,350 18,400 26,410

C-90 8,730 11,630 14,550 18,400 27,130

T-95 9,190 12,260 15,320 18,400 27,590
P-110 10,720 14,300 17,880 18,400 29,120

65.48
L-80 12.70 193.68 8,890 11,850 14,820 193.68 20,730 29,620

N-80 9,020 12,030 15,040 21,010 30,030

C-90 9,820 13,080 16,350 22,250 32,060

T-95 10,340 13,790 17,230 22,250 32,590
P-110 12,070 16,080 20,110 22,250 34,320

72.92
L-80 14.15 190.78 9,990 13,330 16,660

N-80 10,140 13,520 16,890

C-90 11,040 14,710 18,380

T-95 11,630 15,510 19,390
P-110 13,570 18,100 22,630
Q-125 15,210 20,280 25,350
Page 34

31,220
31,430
32,590
33,390
35,970
38,140

10,320
15,420

22,130
22,800
24,070
25,950
26,110
27,140
27,820
29,390
31,550
31,750
32,950
33,720
36,280
37,070
37,280
38,600
39,480
42,360

MLT Ring Field Make-Up Handbook

 API Casing 8-Round LONG Threads

with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(kg/m) Grade (mm) (mm) (N-m) (N-m) (N-m) (mm) (N-m) (N-m) (N-m)

244.48 mm

508.00 mm

139.89
H-40 11.13 485.75 9,120

J-55 12,300

K-55 12,950
M-65 15,580

158.49
J-55 12.70 482.60 14,330

K-55 15,090

197.93
J-55 16.13 475.74 18,710

K-55 19,700
M-65 23,710

MLT Ring Field Make-Up Handbook

Page 35

8-Round LONG Threads (METRIC)

53.57
J-55
8.94 226.59 4,610 6,140 7,670 226.59 10,950 15,560 20,150

K-55 4,980 6,630 8,280 11,820 16,800 20,760
M-65 5,380 7,170 8,960 12,470 17,860 21,440

59.53
J-55 10.03 224.41 5,290 7,050 8,810 224.41 12,510 17,800 25,240

K-55 5,710 7,610 9,500 13,520 19,230 25,940
M-65 6,170 8,230 10,290 14,570 20,740 27,170

L-80 7,390 9,860 12,320 16,880 24,270 29,200

N-80 7,500 9,990 12,490 16,880 24,380 29,370

C-90 8,180 10,900 13,630 16,880 25,060 30,510

T-95 8,610 11,480 14,360 16,880 25,490 31,240

64.73 M-65 11.05 222.38 6,900 9,210 11,510 222.38 16,240 23,140 32,420

L-80 8,270 11,020 13,770 19,470 27,740 34,680

N-80 8,390 11,190 13,980 19,750 28,150 34,880

C-90 9,140 12,190 15,240 20,910 30,040 36,150

T-95 9,640 12,850 16,070 20,910 30,550 36,970
P-110 11,240 14,980 18,720 20,910 32,150 39,630

69.94 M-65 11.99 220.50 7,580 10,100 12,620 220.50 17,770 25,350 37,180

L-80 9,080 12,110 15,130 21,310 30,400 39,680

N-80 9,210 12,270 15,330 21,600 30,800 39,890

C-90 10,030 13,380 16,730 23,540 33,570 41,280

T-95 10,580 14,100 17,630 24,550 35,130 42,180
P-110 12,340 16,450 20,550 24,550 36,890 45,110
Q-125 13,830 18,440 23,050 24,550 38,380 47,600

79.62
L-80 13.84 216.79 10,640 14,200 17,750 216.79 24,740 35,390 49,340

N-80 10,810 14,400 18,010 25,120 35,930 49,600

C-90 11,770 15,690 19,600 27,360 39,130 51,200

T-95 12,410 16,540 20,680 28,850 41,260 52,270
P-110 14,470 19,280 24,110 31,590 46,060 55,700
Q-125 16,220 21,630 27,030 31,590 47,810 58,620

86.91
L-80 15.11 214.25 11,700 15,610 19,510

N-80 11,860 15,820 19,780

C-90 12,930 17,250 21,560

T-95 13,640 18,180 22,720
P-110 15,890 21,190 26,490
Q-125 17,840 23,780 29,730

 API Casing BUTTRESS Threads

BUTTRESS Threads (METRIC)

Weight
(kg/m) Grade

Wall
(mm)

ID
(mm)

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(N-m)
(mm)
(N-m)
(N-m)

114.30 mm

14.14 H-40
5.21 103.89
6,100
102.11
2,370

J-55
6,100
3,270

K-55
6,100
3,270

15.63 J-55
5.69 102.92
6,100
101.75
3,710

K-55
6,100
3,710

M-65
6,100
4,310

17.26 J-55
6.35 101.60
6,100
100.84
4,490

K-55
6,100
4,490

M-65
6,100
4,980

L-80
6,100
4,980

N-80
6,100
4,980

C-90
6,100
4,980

T-95
6,100
4,980

P-110
6,100
4,980

20.09 M-65
7.37 99.57
6,100
99.42
5,990

L-80
6,100
5,990

N-80
6,100
5,990

C-90
6,100
5,990

T-95
6,100
5,990

P-110
6,100
5,990

22.47 P-110 8.56 97.18
6,100
97.18
7,540

Q-125
6,100
7,540

127.00 mm

17.11 J-55
5.59 115.82
6,780
114.76
4,260

K-55
6,780
4,260

M-65
6,780
4,830

19.35 J-55
6.43 114.15
6,780
114.15
5,270

K-55
6,780
5,270

M-65
6,780
114.15
5,270

22.32 J-55
7.52 111.96
6,780
111.96
6,960

K-55
6,780
6,960

M-65
6,780
7,240

L-80
6,780
7,240

N-80
6,780
7,240

C-90
6,780
7,240

T-95
6,780
7,240

P-110
6,780
7,240

26.79 M-65
9.19 108.61
6,780
108.61
10,130

L-80
6,780
10,130

N-80
6,780
10,130

C-90
6,780
10,130

T-95
6,780
10,130

P-110
6,780
10,130

Q-125
6,780
10,130

31.85 M-65 11.10 104.80
6,780
104.80
13,250

L-80
6,780
13,250

N-80
6,780
13,250

C-90
6,780
13,250

T-95
6,780
13,250

P-110
6,780
13,250

Q-125
6,780
13,250

34.53 L-80 12.14 102.72
6,780
102.72
14,870

N-80
6,780
14,870

C-90
6,780
14,870
Page 36

8,470
9,370
9,370
9,820
9,820
10,410
10,590
10,590
11,080
11,080
11,080
11,080
11,080
11,080
12,090
12,090
12,090
12,090
12,090
12,090
13,640
13,640
11,040
11,040
11,610
12,050
12,050
12,050
13,730
13,730
14,020
14,020
14,020
14,020
14,020
14,020
16,910
16,910
16,910
16,910
16,910
16,910
16,910
20,030
20,030
20,030
20,030
20,030
20,030
20,030
21,650
21,650
21,650

MLT Ring Field Make-Up Handbook

 API Casing BUTTRESS Threads

Weight
(kg/m) Grade

Wall
(mm)

ID
(mm)

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(N-m)
(mm)
(N-m)
(N-m)

127.00 mm (continued)

T-95 12.14 102.72
6,780
102.72
14,870

P-110
6,780
14,870

Q-125
6,780
14,870

35.86 L-80 12.70 101.60
6,780
101.60
15,730

N-80
6,780
15,730

C-90
6,780
15,730

T-95
6,780
15,730

P-110
6,780
15,730

Q-125
6,780
15,730

139.70 mm

22,510
22,510
22,510
22,510
22,510
22,510
14,900
14,900
15,420
16,170
16,170
16,590
16,590
16,590
16,590
16,590
16,590
16,590
19,650
19,650
19,650
19,650
19,650
19,650
22,440
22,440
22,440
22,440
22,440
22,440
22,440

168.28 mm

29.76 H-40
7.32 153.64
8,990

J-55
8,990

K-55
8,990

M-65
8,990

35.72 J-55
8.94 150.39
8,990

K-55
8,990

M-65
8,990

L-80
8,990

N-80
8,990

C-90
8,990

T-95
8,990

P-110
8,990

41.67 M-65 10.59 147.09
8,990

L-80
8,990

N-80
8,990

C-90
8,990

T-95
8,990

P-110
8,990

47.62 L-80 12.06 144.15
8,990
MLT Ring Field Make-Up Handbook

Page 37

BUTTRESS Threads (METRIC)

23.07 J-55
6.98 125.73
7,460
125.35
7,440

K-55
7,460
7,440

M-65
7,460
7,960

25.30 J-55
7.72 124.26
7,460
124.26
8,720

K-55
7,460
8,720

M-65
7,460
9,140

L-80
7,460
9,140

N-80
7,460
9,140

C-90
7,460
9,140

T-95
7,460
9,140

P-110
7,460
9,140

Q-125
7,460
9,140

29.76 M-65
9.17 121.36
7,460
121.36
12,190

L-80
7,460
12,190

N-80
7,460
12,190

C-90
7,460
12,190

T-95
7,460
12,190

P-110
7,460
12,190

34.23 M-65 10.54 118.62
7,460
118.62
14,980

L-80
7,460
14,980

N-80
7,460
14,980

C-90
7,460
14,980

T-95
7,460
14,980

P-110
7,460
14,980

Q-125
7,460
14,980

21,650
21,650
21,650

 API Casing BUTTRESS Threads

Weight
(kg/m) Grade

Wall
(mm)

ID
(mm)

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(N-m)
(mm)
(N-m)
(N-m)

168.28 mm (continued)

N-80 12.06 144.15
8,990

C-90
8,990

T-95
8,990

P-110
8,990

Q-125
8,990

BUTTRESS Threads (METRIC)

177.80 mm

29.76 H-40
6.91 163.98
9,490
163.55
8,070

J-55
9,490
11,090

K-55
9,490
11,090

M-65
9,490
11,750

34.23 J-55
8.05 161.70
9,490
161.70
14,340

K-55
9,490
14,340

M-65
9,490
15,080

L-80
9,490
15,080

N-80
9,490
15,080

C-90
9,490
15,080

T-95
9,490
15,080

38.69 J-55
9.19 159.41
9,490
159.41
17,530

K-55
9,490
17,530

M-65
9,490
19,090

L-80
9,490
19,090

N-80
9,490
19,090

C-90
9,490
19,090

T-95
9,490
19,090

P-110
9,490
19,090

43.16 M-65 10.36 157.07
9,490
157.07
23,120

L-80
9,490
23,120

N-80
9,490
23,120

C-90
9,490
23,120

T-95
9,490
23,120

P-110
9,490
23,120

47.62 M-65 11.51 154.79
9,490
154.79
26,950

L-80
9,490
26,950

N-80
9,490
26,950

C-90
9,490
26,950

T-95
9,490
26,950

P-110
9,490
26,950

52.09 L-80 12.65 152.50
9,490
152.50
30,700

N-80
9,490
30,700

C-90
9,490
30,700

T-95
9,490
30,700

P-110
9,490
30,700

Q-125
9,490
30,700

56.55 L-80 13.72 150.37
9,490
150.37
34,130

N-80
9,490
34,130

C-90
9,490
34,130

T-95
9,490
34,130

P-110
9,490
34,130

Q-125
9,490
34,130

32,610
32,610
32,610
32,610
32,610
32,610

39.29

17,480
17,480
18,470
18,470
18,470
18,470

Page 38

J-55
8.33 177.01
K-55
M-65
L-80
N-80
C-90

193.68 mm

10,340
177.01
10,340
10,340
10,340
10,340
10,340

17,480
17,480
18,470
18,470
18,470
18,470

17,560
20,580
20,580
21,250
23,830
23,830
24,570
24,570
24,570
24,570
24,570
27,020
27,020
28,580
28,580
28,580
28,580
28,580
28,580

36,440
36,440
36,440
36,440
36,440
36,440
40,190
40,190
40,190
40,190
40,190
40,190
43,620
43,620
43,620
43,620
43,620
43,620

MLT Ring Field Make-Up Handbook

 API Casing BUTTRESS Threads

Weight
(kg/m) Grade

Wall
(mm)

ID
(mm)

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(N-m)
(mm)
(N-m)
(N-m)

193.68 mm (continued)

219.08 mm

35.72 J-55
6.71 205.66
11,700
204.62
14,870

K-55
11,700
14,870

M-65
11,700
17,100

41.67 H-40
7.72 203.63
11,700
203.63
14,100

M-65
11,700
19,850

47.62 H-40
8.94 201.19
11,700

J-55
11,700

K-55
11,700

M-65
11,700

53.57 J-55 10.16 198.76
11,700
198.76
29,870

K-55
11,700
29,870

M-65
11,700
33,080

L-80
11,700
33,080

N-80
11,700
33,080

C-90
11,700
33,080

T-95
11,700
33,080

59.53 M-65 11.43 196.22
11,700
196.22
39,780

L-80
11,700
39,780

N-80
11,700
39,780

C-90
11,700
39,780

T-95
11,700
39,780

P-110
11,700
39,780

65.48 L-80 12.70 193.68
11,700
193.68
46,340

N-80
11,700
46,340

C-90
11,700
46,340

T-95
11,700
46,340

P-110
11,700
46,340

244.48 mm

53.57 H-40
8.94 226.59
13,060
226.59
22,490

J-55
13,060
30,910

K-55
13,060
30,910

M-65
13,060
33,260

59.53 J-55 10.03 224.41
13,060
224.41
36,780
MLT Ring Field Make-Up Handbook

18,470
23,470
23,470
23,470
23,470
23,470
23,470
29,180
29,180
29,180
29,180
29,180
29,180
36,240
36,240
36,240
36,240
36,240
36,240
26,570
26,570
28,800
25,800
31,550

41,570
41,570
44,780
44,780
44,780
44,780
44,780
51,480
51,480
51,480
51,480
51,480
51,480
58,040
58,040
58,040
58,040
58,040
35,550
43,970
43,970
46,310
49,840
Page 39

BUTTRESS Threads (METRIC)

T-95
8.33 177.01
10,340
177.01
18,470

44.20 M-65
9.52 174.63
10,340
174.63
23,470

L-80
10,340
23,470

N-80
10,340
23,470

C-90
10,340
23,470

T-95
10,340
23,470

P-110
10,340
23,470

50.15 M-65 10.92 171.83
10,340
171.83
29,180

L-80
10,340
29,180

N-80
10,340
29,180

C-90
10,340
29,180

T-95
10,340
29,180

P-110
10,340
29,180

58.04 L-80 12.70 168.28
10,340
168.28
36,240

N-80
10,340
36,240

C-90
10,340
36,240

T-95
10,340
36,240

P-110
10,340
36,240

Q-125
10,340
36,240

 API Casing BUTTRESS Threads

BUTTRESS Threads (METRIC)

Weight
(kg/m) Grade

Wall
(mm)

ID
(mm)

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(N-m)
(mm)
(N-m)
(N-m)

244.48 mm (continued)

K-55 10.03 224.41
13,060
224.41
36,780
49,840

M-65
13,060
40,660
53,720

L-80
13,060
40,660
53,720

N-80
13,060
40,660
53,720

C-90
13,060
40,660
53,720

T-95
13,060
40,660
53,720

64.73 M-65 11.05 222.38
13,060
222.38
45,530
58,580

L-80
13,060
47,450
60,510

N-80
13,060
47,450
60,510

C-90
13,060
47,450
60,510

T-95
13,060
47,450
60,510

P-110
13,060
47,450
60,510

69.94 M-65 11.99 220.50
13,060
220.50
53,640
66,690

L-80
13,060
53,640
66,690

N-80
13,060
53,640
66,690

C-90
13,060
53,640
66,690

T-95
13,060
53,640
66,690

P-110
13,060
53,640
66,690

Q-125
13,060
53,640
66,690

79.62 L-80 13.84 216.79
13,060
216.79
65,610
78,660

N-80
13,060
65,610
78,660

C-90
13,060
65,610
78,660

T-95
13,060
65,610
78,660

P-110
13,060
65,610
78,660

Q-125
13,060
65,610
78,660

60.27 H-40
8.89 255.27

J-55

K-55

M-65

273.05 mm

27,960
38,440
38,440
41,300

42,530
53,010
53,010
55,870

67.71 J-55 10.16 252.73

14,570
252.73
47,030

K-55
14,570
47,030

M-65
14,570
52,140

75.90 J-55
11.43 250.19
14,570
250.19
55,490

K-55
14,570
55,490

M-65
14,570
62,810

L-80
14,570
62,810

N-80
14,570
62,810

C-90
14,570
62,810

T-95
14,570
62,810

P-110
14,570
62,810

82.59 M-65 12.57 247.90
14,570
247.90
72,280

L-80
14,570
72,280

N-80
14,570
72,280

C-90
14,570
72,280

T-95
14,570
72,280

P-110
14,570
72,280

Q-125
14,570
72,280

90.33 C-90 13.84 245.36
14,570
245.36
82,620

T-95
14,570
82,620

P-110
14,570
82,620

Q-125
14,570
82,620

61,610
61,610
66,720

69.94 J-55
9.53 279.40

K-55
Page 40

14,570
255.27
14,570
14,570
14,570

298.45 mm

15,930
279.40
15,930

51,290
51,290

70,070
70,070
77,390
77,390
77,390
77,390
77,390
77,390
86,850
86,850
86,850
86,850
86,850
86,850
86,850
97,200
97,200
97,200
97,200

67,220
67,220

MLT Ring Field Make-Up Handbook

 API Casing BUTTRESS Threads

Weight
(kg/m) Grade

Wall
(mm)

ID
(mm)

with MLT Ring (L-80)

Estimated
Total
Torque
Ring
Delta
Torque
(no rings)
ID
Torque
MAX
(N-m)
(mm)
(N-m)
(N-m)

298.45 mm (continued)

339.73 mm

81.10 J-55
9.65 320.42
18,140
319.41
68,130

K-55
18,140
68,130

M-65
18,140
80,510

90.78 J-55 10.92 317.88
18,140
319.41
81,630

K-55
18,140
81,630

M-65
18,140
81,630

101.19 J-55 12.19 315.34
18,140
319.41
81,630

K-55
18,140
81,630

M-65
18,140
81,630

L-80
18,140
81,630

N-80
18,140
81,630

C-90
18,140
81,630

T-95
18,140
81,630

P-110
18,140
81,630

107.15 L-80 13.06 313.61
18,140
319.41
81,630

N-80
18,140
81,630

C-90
18,140
81,630

T-95
18,140
81,630

P-110
18,140
81,630

Q-125
18,140
81,630

MLT Ring Field Make-Up Handbook

72,020
79,530
79,530
87,560
90,430
90,430
101,310
101,310
101,310
101,310
101,310
101,310
101,310
112,600
112,600
112,600
112,600
112,600
112,600
86,270
86,270
98,650
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770
99,770

Page 41

BUTTRESS Threads (METRIC)

M-65
9.53 279.40
15,930
279.40
56,090

80.36 J-55
11.05 276.35
15,930
276.35
63,600

K-55
15,930
63,600

M-65
15,930
71,630

89.29 J-55 12.42 273.61
15,930
273.61
74,500

K-55
15,930
74,500

M-65
15,930
85,370

L-80
15,930
85,370

N-80
15,930
85,370

C-90
15,930
85,370

T-95
15,930
85,370

P-110
15,930
85,370

Q-125
15,930
85,370

96.73 L-80 13.56 271.32
15,930
271.32
96,670

N-80
15,930
96,670

C-90
15,930
96,670

T-95
15,930
96,670

P-110
15,930
96,670

Q-125
15,930
96,670

II. RECOMMENDED PRACTICES

API Casing and Tubing Threads
The following recommendations include selected highlights
from API publications listed in Appendix B. (REFERENCES)
of this manual as well as generally accepted industry
practices. For proprietary products and services it is
recommended the reader consult the manufacturers
recommended practices.
a. Storage and Handling Casing
1. Casing should always be handled with thread
protectors in place. Casing should be handled on
racks or on wooden or metal surfaces free from
rocks, sand, or dirt other than normal drilling mud.
2. The storage life of pipe threads may be improved
by cleaning coupling and pipe threads and applying
a water displacing pipe storage compound. If a
storage compound is used, care should be taken to
clean threads and remove the storage compound
and replace with running compound prior to running
casing downhole. (Storage compounds lack sealing
performance required for API threads.)
3. Pipe stacked in layers should be separated with
wooden runners to facilitate rolling or picking up with
a forklift.
4. For safety, durable chocks should be used on pipe
runners to prevent unwanted pipe movement.

b. Preparation for Running Casing

The following precautions should be taken in the
preparation for running casing and power tight assembly
of threads.
1. Equipment to be used should be inspected and
tested.
2. The traveling and crown blocks should have the
proper number of lines to support the expected casing
load.
Page 42

MLT Ring Field Make-Up Handbook

3. Slip-type elevators are recommended. Both floor and

elevator slips should be clean, have proper dies and
should fit properly. Care should be taken to ensure
the floor slip is level.
4. Casing handling equipment and slips should be
checked for proper size and examined to see that all
segments lower together. If they lower unevenly there
is danger of denting or slip-cutting the pipe.
5. Verify each pipe joint as to weight, grade and thread
type and ensure it is in the proper running order.
Identify all crossover joints and the first joint of each
weight, grade or thread type with easy-to-see paint
or chalk.
6. Immediately before running casing, remove thread
protectors from both field and coupling ends and clean
the threads thoroughly, repeating as additional rows
become uncovered.
7. Carefully inspect the threads. Those found damaged
should be laid aside unless satisfactory means are
available for correcting thread damage.
8. Number and tally each joint of casing as it is loaded
on the rack. While running casing, number each
joint as it goes in the hole (1,2,3, etc) taking care
to identify joints not being run. A steel tape calibrated
in: A) decimal feet to the nearest tenth of a foot B)
decimal meter to the nearest tenth of a meter should
be used. The threads off measurement should be
made from the outer most face of the coupling to
the position on the externally threaded end where
the coupling stops when made up power tight. On
round-thread pipe, this position is to the plane of the
vanish point on the pipe (also known as last scratch;
on buttress thread pipe, this position is to the base
of the triangle steel stamp on the pipe.) The total of
the individual lengths so measured will represent the
unloaded length of the pipe string. If the pipe tally is
made with threads on (full length of pipe) then the
running footage can be calculated using adjustment
factors found in Appendix. C. The actual length under
tension will be greater due to stretch of the pipe under
load.

MLT Ring Field Make-Up Handbook

Page 43

9. Couplings on the mill end of the pipe should be madeup power-tight. Check each coupling for make-up. If
the standoff is abnormally great, tighten the coupling
before pulling the pipe into the derrick. (For round
threads, refer to the appropriate torque tables.)
10. Before stabbing, apply thread compound to the
entire internally and externally threaded areas. It is
recommended that a thread compound that meets
the performance objectives of API Bulletin 5A2 be
used. The brush or utensil used in applying thread
compound should be kept free of foreign matter, and
the compound should never be thinned.
11. Place a clean thread protector on the field end (pin
end) of the pipe to protect the thread while rolling
pipe on the rack and raising it into the derrick. It is
recommended that thread protectors from field ends
of pipe not be removed until ready to stab.
12. It is recommended that each length of pipe be drifted
its entire length before running downhole. Care
should be taken to ensure the drift mandrels conform
to the requirements of API 5CT by measuring the
drifts length and diameter before each job.
c. General Practices for Field Make-Up, API ROUND and
BUTTRESS threads (without MLTTM Rings)
1. API round thread make-up torque guidelines are
included in the enclosed tables and are the primary
reference for checking make-up.
2. API buttress thread make-up uses position as the
primary reference but an estimate of the makeup (shoulder) torque is provided in the tables for
information and use with MLTTM Ring total torque
calculations.
3. The torque values represented in the tables are
for make-up with API modified thread compound.
Use of other compounds may result in higher or
lower torques. Torque values for some widely used
compounds with Teflon particles will usually be
approximately 10% less, and for these compounds
multiplying the API recommended torque numbers
by a factor of 0.9 is recommended.
Page 44

MLT Ring Field Make-Up Handbook

4. Torque values are affected by a large number of

variables, such as variations in taper, lead, thread
height and thread forms, surface finish, type of thread
compound, length of thread, weight and grade of
pipe, etc.
5. The torque values included in the Torque Tables
herein apply to casing with zinc-plated or phosphatecoated couplings. For API connections with other
coupling coatings or platings, couplings with the
modified feature (seal rings), or using other than API
Modified, the torques in the included tables should
be adjusted by multiplying torques by the following
factors:

Factor

Tin plated couplings

0.80

Couplings with PTFE (Teflon) rings
0.70
6. As a visual aid to the make-up operator the first
joints of pipe run should have a reference mark put
on them to locate the run out of 8-round threads or
the triangle make-up reference mark for buttress and
large diameter casing.
7. In stabbing, lower pipe carefully to avoid damaging
threads. Stab vertically and rotate very slowly at first
to ensure that threads are engaging properly and not
cross-threading.
d. Practices for ROUND Thread Casing, Sizes 4-1/2
through 13-3/8 OR 114mm through 340mm
1. Primary reference to proper make-up is to apply
torque with cross-reference to position.
2. It is advisable when starting to run casing from
each particular mill shipment to make up sufficient
joints to determine the torque necessary to provide
proper makeup. Thread dimensions can vary from
lot to lot. See API Spec 5B for the proper number
of turns beyond hand-tight position. These values
may indicate that a departure from the values listed
in the torque tables is advisable. If other values
are chosen, the minimum torque should be not less
than 75% of the value selected and the maximum
torque should not be more than 125% of the selected
torque.
MLT Ring Field Make-Up Handbook

Page 45

3. The top drive (or power tong) should be provided

with a reliable torque-measuring gauge of known
accuracy. In the initial stages of makeup, any
irregularities of makeup or in speed of makeup
should be observed, since these may be indicative of
crossed threads, dirty or damaged threads, or other
unfavorable conditions. Unexpectedly high torque
and/or excessive heat build up in the coupling are
indications of cross-threading or galling. To prevent
galling when making up connections in the field, the
connections should be made up at a speed not to
exceed 25 rpm.
4. Continue the makeup, observing both the torque
gauge and the approximate position of the coupling
face with respect to the thread vanish point position
(also known as last scratch).
5. The torque values shown in the attached tables
have been selected to give recommended makeup
under normal conditions and should be considered
as satisfactory providing the face of the coupling is
flush with the thread vanish point or within plus or
minus two thread turns.
6. If the makeup is such that the thread vanish point
is buried two thread turns and the minimum torque
shown in torque tables is not reached, the joint
should be treated as a questionable joint as provided
for in paragraph g below. If several threads remain
exposed when the listed torque is reached, apply
additional torque up to the maximum torque shown
in the torque tables. If the standoff (distance from
the face from the coupling to the thread vanish point,
also referred to as last scratch) is greater than
three thread turns when this additional torque is
reached, the joint should be treated as questionable
as provided in paragraph g below.
7. Questionable joints should be laid down. When this
is done, the mating coupling should be carefully
inspected for damaged threads. (Parted joints
should never be reused without rethreading or
re-gauging, even though the joints may have little
appearance of damage.)

Page 46

MLT Ring Field Make-Up Handbook

e. Practices for BUTTRESS Thread Casing, Sizes 4-1/2

through 13-3/8 OR 114.30mm through 339.73mm
1. Primary reference to proper make-up is to position
with respect to the 3/8 high die-stamped triangle
with cross-reference to torque.
2. Make-up torque values should be determined by
carefully noting the torque required to make-up
several connections to the base of the triangle; then
using the torque value thus established, make-up
the balance of the pipe of that particular weight and
grade in the string. Periodically check to ensure
proper position is being maintained.
3. The tolerance for make-up position places the face
of the coupling between the apex of the triangle
and one thread pitch (0.200) below the base of the
triangle, for a total make-up window of 0.575 (2.9
turns).
4. The top drive (or power tong) should be capable of
attaining high torques as maximum torques values
could be five times the minimum experience in
makeup to the recommended position.
f. Practices for ROUND and BUTTRESS Thread Casing,
Sizes 16, 18-5/8 and 20 OR 406.45mm, 473.10mm
and 508mm
1. Primary reference to proper make-up is position.
Variations in torque are much greater on large
diameter casing due to the influence of pipe
ovality.
2. Make-up shall be to a position on each connection
represented by the thread vanish point on 8-round
threads and the base of the triangle on buttress
threads, using the torques shown in the tables as a
guide.
3. On 8-round thread casing a 3/8 (9.5mm) high
equilateral triangle is die stamped at a distance of
L1+1/16 (L1+1.6mm) from each end. The base of
the triangle will aid in locating the thread vanish point
for basic power-tight make-up. Extra care should be
taken to avoid cross-threading in starting these larger
connections.

Note: L1 is the length of end of the pipe to the handtight plane. (Ref. API 5B)

MLT Ring Field Make-Up Handbook

Page 47

g. Joints that are questionable as to their proper tightness

should be unscrewed and the casing laid down for
inspection and repair. When this is done, the mating
coupling should be carefully inspected for damaged
threads. Parted joints should never be reused without
a shop check or regauging, even though the joints may
have little appearance of damage.
h. Casing wobble indicates the thread may not be in line
with the axis of the casing and is usually minimized when
using a top drive. If casing has a tendency to wobble
unduly at its upper end when making-up with a tong the
speed of rotation should be decreased to prevent galling
of threads. If wobbling should persist despite reduced
rotational speed, the casing should be laid down for
inspection. Serious consideration should be given before
using such casing in a position in the string where heavy
tensile load is imposed.
i. In making up the field joint, it is possible for the coupling
to make up slightly on the mill end. This does not indicate
that the coupling on the mill end is too loose but simply
that the field end has reached the tightness with which
the coupling was screwed on at the manufacturers
facility.
j. If possible, fill casing as it is being run. If automatic
float/fill equipment is used, stop and check to ensure they
are operating. Floating the casing in is a poor practice
and should be avoided.
k. It is recommended to break circulation slowly just prior
to tagging bottom and before any pipe reciprocating is
carried out.
l. Tag bottom carefully. Excess slack-off will buckle the
string and damage the connections.

Page 48

MLT Ring Field Make-Up Handbook

III. TESCO MLT (Multi-Lobe Torque) Rings

a. APPLICATIONS MLT Rings are steel rings inserted

into the couplings of standard API threaded and coupled
tubing and casing connections. The ring provides a
number of benefits, including a mechanical shoulder
for the ends of the pin ends to increase torque capacity.
TESCO Corporation has designed MLT Rings for use
in drilling and production operations with both casing and
tubing. Applications include:

Tubing 2-3/8, 2-7/8 & 3-1/2

OR 60.32mm, 73.02mm & 88.90mm
- Production tubing and work strings
- Gas wells
- Progressive Cavity Pump (PCP) strings
- Well abandonment
Casing 4-1/2 thru 13-3/8
OR 114.30mm through 339.73mm
- Casing drilling
- Liners
TM
- Casing Running for strings or applications
requiring rotation under high torque and drag

b. FEATURES MLT Rings

Steel rings - Rings are machined from steel that
meets API grade requirements and designed to fit
standard API Round and Buttress thread connections.
No special pipe or coupling threading specification is
required.
Engineering - MLT Rings are engineered to fit
precisely against API connection surfaces. The
rings are designed with a unique non-circular shape
or lobes. After installation, the lobed sections of the
MLT Rings press firmly across the tapered threads
MLT Ring Field Make-Up Handbook

Page 49

of API connections to retain them in place and ID

becomes circular.
Secure MLT Rings stay firmly in place during
transportation, handling, and use.
Easy installation Rings are inserted into couplings
using a simple hydraulic installation tool. Easy to
use ring selection gauge is used to determine which
length ring is required for each connection.
c. PERFORMANCE and APPLICATIONS
1. Torque Capacity of MLT Rings provide a
significant boost to API torque ratings, referred
to as the Delta Torque. Delta torques and total
torques are provided in the Torque Tables.
2. Tubing and Casing
a) High torsional strength for drilling and/or
rotating applications using standard API
threads.
b) Blocks sand and debris from entering threads.
3. Tubing - Work Strings
a) Prolongs string life.
b) Increases durability of API tubing threads
by reducing over penetration of the pin
into the coupling.
4. Tubing - Gas Wells
a) Reduces turbulence and erosion in
connections
b) Increases durability of API tubing threads
by reducing coupling and pin stresses that
occur from over-penetration of the pin into the
coupling.

5. Tubing - Progressing Cavity Pump (PCP) Strings

a) Reduces incidence of connection backoff when rotor becomes stuck. Increases
durability of API tubing threads by reducing
coupling and pin stresses that occur from overpenetration of the pin into the coupling.
b) Eliminates tubing anchor.
6. Casing Liners - Enhances running of long liners in
deviated wells by increasing torsional capacity of
connections.

Page 50

MLT Ring Field Make-Up Handbook

d. RING IDENTIFICATION

Proper identification of rings includes the following:

1. OD of pipe

3. Grade of steel

4. Color - GREEN or RED or BLUE or YELLOW

identifying the respective ring length from shortest to
longest. Red and blue rings will dominate usage.

2. Weight per foot of the pipe

Example: 7 23# L-80 Red

177.80 mm 34.23 Kg/m L-80 Red

Note: As an added aid in identifying MLT Rings, each

ring has one to four grooves lightly machined into
the ID of the ring on the outboard end. One groove
= green, two grooves = red; three grooves = blue
and four grooves = yellow.

MLT Ring Field Make-Up Handbook

Page 51

e. RECOMMENDED Field Make-up Practices API

Threads with MLT Rings
The following recommended practices are for use with MLT
Rings and are in addition to the recommended practices
described in the previous Section II. Care should also be
taken to follow the preparation and running procedures in
Section II.
Running Procedure
Remove protectors and visually inspect the pin and
coupling threads. Threads should be clean and free
of defects.
Ensure the MLT Ring is installed properly and is
seated in the center of the coupling against the mill
end pin. Ring installation is easily performed with a
hydraulic installation tool. For proper ring installation
procedures, contact TESCO.
Apply a thin even coat of thread compound to the
coupling and pin threads.
Refer to the torque tables and select the appropriate
maximum torque for the casing or tubing and the ring
being used.
Set the pressure relief valve, or dump valve, on the
tong to relieve at the specified make-up torque.
Apply back-up jaws to the mill end pipe body during
make-up.
Make-up the first connection to the target torque as
specified. make-up speed at the point the pin contacts
the ring should not exceed 15 RPM.
Ensure Acceptance Criteria are met (see following
table).
Record the torque just prior to the pin shouldering on
the ring. At the shoulder point, the torque will increase
sharply.
If necessary, adjust the tong torque setting so as not to
exceed the delta torque but ensuring the pin shoulders
on the ring.
Continue to make up the remainder of the string.

Page 52

MLT Ring Field Make-Up Handbook

CRITERIA

CORRECTIVE ACTION
if criterion not met:

1. Pin must shoulder

on ring
Note
Shouldering should
be accompanied by a
sharp increase in torque
relative to rotation. It
may be useful to initially
mark the first few pin
ends with a paint stick
indicating the position of
pin contact with the ring
as a visual reference.

1) Back off one turn.

2) Re-make the connection,
increasing the maximum
applied torque for this
connection only, then
resetting the torque.
3) Re-check acceptance
criteria.

2. For round threads,

shoulder torque
should exceed a
MINIMUM value of 40%
(approximate) of delta
torque.

1) Break out the

connection and inspect
pin.
2) Change out the coupling
and install a new
MLT ring. (See ring
installation section)
3) Drift each component
of the connection. Lay
down joints that do not
drift. If both components
drift, proceed to step
four.
4) Re-make the
connection, ensuring
minimum shoulder
torque is met and
maximum delta torque is
not exceeded.
5) If shoulder torque is
still less than minimum
acceptable value after
the second make-up, lay
down pin joint.
6) Re-check acceptance
criteria.

MLT Ring Field Make-Up Handbook

Page 53

CRITERIA

CORRECTIVE ACTION
if criterion not met:

3. Maximum delta torque

must not be exceeded
during make-up.

1) Check that the

connection is made up to
position. (Last thread not
visible on field end)
2) If the connection is made
up to position, check
drift. If connection drifts
and is at position, makeup is acceptable.
3) If drift mandrel will not
pass or connection
is not at position,
break out connection
and inspect for visual
damage, galling, etc. If
undamaged, proceed to
step four. Otherwise, lay
down joints.
4) After breakout, drift the
coupling and pin ends.
a) If the drift requirement
is not met in one or
both components, it
is a sign of excessive
deformation during
makeup, lay down
joints.
b) If both pin and
coupling drift, install
a new MLT Ring
and remake with
proper Delta toque
and re-drift. (See ring
installation section.)
If the connection still
does not drift set
aside both joints.
This rare occurrence
indicates undesirable
geometry and will
compromise torsion
capacity.

AND
Connection rotation
must not exceed 1/8
turn after shouldering
(avoids forcing the ring
to encroach on the drift
diameter).

Page 54

MLT Ring Field Make-Up Handbook

CRITERIA

CORRECTIVE ACTION
if criterion not met:
c) If pin drifts and coupling
does not, change out
the coupling and install
a new MLT Ring. (See
Field Ring Installation
Par.III-f)
d) If coupling drifts and pin
does not, lay down joint
and re-use the coupling
and ring.
e) If similar damage
is observed on the
new part during the
next make-up, lay
down both joints.
This also indicates an
unfavorable geometry.

MLT Ring Field Make-Up Handbook

Page 55

CRITERIA
f. FIELD Ring Installation
(Floating rings without install kit)
For tubing only, if an installation kit is not readily available,
the rings can be installed by letting the connection make-up
press the ring into place with the following procedure.
Thread the coupling on the mill end hand tight. Install a RED
MLT Ring in the coupling by hand with the color facing up.
Float the connection make-up not exceeding 10 RPM during
make-up. In the unlikely event that the shoulder torque is
below MINIMUM acceptable noted in the acceptance criteria
above, remove the coupling, install a GREEN MLT Ring
and re-make. If the shoulder torque is again below the
MINIMUM then the joint should be set aside.

Page 56

MLT Ring Field Make-Up Handbook

IV. Breaking Out Connections

If it is necessary to break out connections, the following
procedures are recommended.
a. For breaking out connections on the field end on
rig floor, the backup tong should be placed on
the coupling to help preclude deforming the pipe,
particularly important for lighter wall thickness pipe,
and preclude backing off the connection on the mill
side. Slips can be used for backup as long as the
weight on string is adequate and the pipe does not
turn in the slips cutting the pipe. It is preferred to
apply back-out torque with the top drive or power
tongs as these will distribute the applied forces better
than rig tongs.
b. If the pipe is not breaking-out easily it is acceptable
to use the manual tongs and recommended they
be used in combination with the top drive or power
tongs.
c. If tongs are used to break-out connections, the grips
should be positioned close to the coupling. Tong
grips should be clean and have proper dies.
d. Connection break-out torque typically is 10 % to 30
% higher than make-up torque. Higher break-out
torque up to double the make-up torque can be
influenced by factors such as use of compounds
with Teflon and / or drill string vibration encountered
during casing drilling.
e. After connections are broken out, both pin and
coupling threads should be cleaned and inspected
for thread damage. Any metal whiskers found should
be removed and galled spots should be carefully
repaired.

MLT Ring Field Make-Up Handbook

Page 57

APPENDIX A. DEFINITIONS
Delta Torque

The boost in torque capacity of a connection with
MLT Rings installed. Delta torque is added to
shoulder torque to obtain total torque capacity.
Shoulder Torque

A term applicable for use with MLTTM rings. During
power tight connection make-up it is the torque
just before the pin contacts the face of the installed
MLTTM ring. It is observed as the pin contacts the
ring followed by a sharp increase in torque. It can
be estimated by the API recommended torques for
round thread and by the approximations in the tables
for buttress.
MLTTM Ring

Multi-Lobe Torque Ring, trade marked name of
TESCOs torque rings
APPENDIX B. REFERENCES
API Bul 5A2

Bulletin on Thread Compounds for Casing,

Tubing, and Line Pipe

API Bul 5C2 Bulletin on Performance Properties of

Casing, Tubing, and Drill Pipe
API Bul 5C3

Bulletin on Formulas and Calculations for

Casing, Tubing, Drill Pipe, and Line Pipe
Properties

API RP 7G

Recommended Practice for Drill Stem Design

and Operating Limits

API Spec 5B Specification for Threading, Gauging, and

Thread Inspection of Casing, Tubing, and
Line Pipe Threads
API Spec 5CT Specification for Casing and Tubing
TESCO Corp. Specifications and recommended practices

Page 58

MLT Ring Field Make-Up Handbook

APPENDIX C. THREAD MAKE-UP LOSS

IMPERIAL - API THREAD LENGTH FOR MAKE-UP LOSS
O.D.
EUE
Short
Long
Buttress
(in)
Thread
Thread
Thread
Thread
Length
Length
Length
Length
(in)
(in)
(in)
(in)
2 3/8
1.938
2 7/8
2.125
3 1/2
2.375
4 1/2
2.625
3.000
3.938
5
2.750
3.375
4.063
5 1/2
2.875
3.500
4.125
6 5/8
3.125
3.875
4.313
7
3.125
4.000
4.500
7 5/8
3.250
4.125
4.688
8 5/8
3.375
4.500
4.813
9 5/8
3.375
4.750
4.813
10 3/4
3.500
4.813
11 3/4
3.500
4.813
13 3/8
3.500
4.813
16
4.000
4.813
18 5/8
4.000
4.813
20
4.000
5.250
4.813
METRIC - API THREAD LENGTH FOR MAKE-UP LOSS
O.D.
EUE
Short
Long
Buttress
(mm)
Thread
Thread
Thread
Thread
Length
Length
Length
Length
(mm)
(mm)
(mm)
(mm)
60.32
49.2
73.02
54.0
88.90
60.3
114.30
66.7
76.2
100.0
127.00
69.9
85.7
103.2
139.70
73.0
88.9
104.8
168.28
79.4
98.4
109.6
177.80
79.4
101.6
114.3
193.68
82.6
104.8
119.1
219.08
85.7
114.3
122.3
244.48
85.7
120.7
122.3
273.05
88.9
122.3
298.45
88.9
122.3
339.73
88.9
122.3
406.40
101.6
122.3
473.10
101.6
122.3
508.00
101.6
133.4
122.3
Reference: API Spec 5B - Specification for Threading, Gauging,
and Thread Inspection of Casing, Tubing, and Line
Pipe Threads
MLT Ring Field Make-Up Handbook

Page 59

Notes
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________

APPENDIX D Conversion factors

COMMON METRIC CONVERSION FACTORS

Length:

in x 2.54 = cm
cm x 0.3937 = inch
ft x 0.3048 = metre
m x 3.281 = ft
miles x 1.609 = km
km x 0.6214 = miles

Area:

acres x 0.4047 = hectares

hectares x 2.471 = acres
km2 x 100 = hectares
hectares x 0.01 = km2

Volume (Gas):

scf x 0.02832 = scm

scm x 35.314 = scf

Volume (Fluid):

gal x 3.7854 = litre

BBL x 0.159 = m3
ft3 x 0.0283 = m3
in 231 = US Gallons

Pressure:

psi x 6.8947 = kPa

kPa x 0.145 = psi

Mass:

lbm x 0.4536 = kg
kg x 2.2 = lbm
tonne x 2,205 = 1bm

Force:

lbs x 0.4448 = daN

ft-lbs x 0.13558 = daN-m

Density (Fluid):

lb/gal x 119.9 = kg/m

Power:

HHP x 0.746 = kW

Gas-Liquid Ratio:

scf/BBL x 0.1781 = m/m

m/m x 5.613 = scf/BBL

Temperature:

(F - 32) x 0.556 = C
(1.8 x C) + 32 = F

MLT Ring Field Make-Up Handbook

Page 61


with MLT Ring (L-80)

API Recommended
Total

Torques
Ring Delta
Torque
Weight
Wall
ID
MIN OPT MAX
ID Torque MIN
MAX
(lb/ft) Grade (in)
(in) (ft-lb) (ft-lb) (ft-lb) (in) (ft-lb) (ft-lb) (ft-lb)

TESCO MLT Rings

The Drilling Innovation Company

CASING DRILLING

Email: [email protected] Web: www.tescocorp.com

Corporate Headquarters
6204 - 6A Street S.E.
Calgary, Alberta, Canada T2H 2B7
Tel: 403 692-5700 Fax: 403 692-5710
Page 62

World Wide Operations

11330 Brittmoore Park Drive
Houston, Texas, USA 77041
Tel: 713 849-5900 Fax: 713 849-0075

Printed in Canada / TESCO Corporation / November 2005 / .5M LG

MLT
Fieldwithout
Make-Up
Due to ongoing product development, all specifications are
subjectRing
to change
notice.Handbook
*Patent Pending

Due to ongoing product development, all specifications