LCD TV: Service Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 99

Internal Use Only

North/Latin America Europe/Africa Asia/Oceania http://aic.lgservice.com http://eic.lgservice.com http://biz.lgservice.com

LCD TV SERVICE MANUAL


CHASSIS : LD01U

MODEL : 32LK330/330A/330N/330U/331 MODEL : 32LK330/330A/330N/330U-ZB MODEL : 32LK331-ZA


CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL62863073 (1102-REV00)

Printed in Korea

CONTENTS

CONTENTS .............................................................................................. 2 PRODUCT SAFETY ................................................................................. 3 SPECIFICATION ....................................................................................... 6 ADJUSTMENT INSTRUCTION ................................................................ 9 BLOCK DIAGRAM...................................................................................15 EXPLODED VIEW .................................................................................. 16 SCHEMATIC CIRCUIT DIAGRAM ..............................................................

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

-2-

LGE Internal Use Only

SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB. Keep wires away from high voltage or high temperature parts.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit


AC Volt-meter

Before returning the receiver to the customer,


always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)


With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 M and 5.2 M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

To Instrument's exposed METALLIC PARTS

0.15 uF

Good Earth Ground such as WATER PIPE, CONDUIT etc.

1.5 Kohm/10W

When 25A is impressed between Earth and 2nd Ground for 1 second, Resistance must be less than 0.1 *Base on Adjustment standard

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

-3-

LGE Internal Use Only

SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 F to 600 F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500 F to 600 F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500 F to 600 F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.

-4-

LGE Internal Use Only

IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

-5-

LGE Internal Use Only

SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range
This specification is applied to the LCD TV used LD01U chassis.

3. Test method
1) Performance: LGE TV test method followed 2) Demanded other specification - Safety: CE, IEC specification - EMC:CE, IEC

2. Requirement for Test


Each part is tested as below without special appointment. 1) Temperature : 25 C 5 C (77 F 9 F), CST : 40 C 5 C 2) Relative Humidity : 65 % 10 % 3) Power Voltage : Standard input voltage (AC 100-240 V~ 50 / 60 Hz) * Standard Voltage of each products is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 5 minutes prior to the adjustment.

4. Model General Specification


No. 1 Market Item Specification EU(PAL Market-36Countries) DTV-T/C & Analog (Germany, Netherlands, Switzerland, Hungary, Austria, Slovenia, Sweden, Denmark, Finland, Norway, Bulgaria DTV-T & Analog UK, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia,Turkey, Moroco, Ireland, Latvia, Estonia, Lithania, Poland, Portugal, Romania, Ukraine Analog Only Kazakhstan, Albania, Bosnia, Serbia, Slovakia 2 Broadcasting system 1) PAL-BG 2) PAL-DK 3) PAL-I/I 4) SECAM L/L 5) DVB-T/C/S (ID TV) 3 Receiving system Analog : Upper Heterodyne Digital : COFDM, QAM 4 5 6 7 8 Scart Jack (1EA) PAL, SECAM Scart Jack is Full scart and support RF-OUT(analog & DTV) 4System : PAL, SECAM, NTSC, PAL60 Remarks

Video Input RCA(1EA) PAL, SECAM, NTSC Component Input(1EA) Y/Cb/Cr, Y/Pb/Pr RGB Input HDMI Input (3EA) RGB-PC HDMI1-DTV (DVI) HDMI2-DTV HDMI3-DTV

Analog(D-SUB 15PIN) PC(HDMI version 1.3) Support HDCP

Audio Input (3EA)

RGB/DVI Audio, Component, AV SPDIF out Antenna, AV1, AV2, AV3, Component, RGB, HDMI1, HDMI2, HDMI3, HDMI4

L/R Input

10 SDPIF out (1EA) 11 Earphone out (1EA)

12 USB (1EA)

For SVC (download) DivX

13 DVB

DVB-T

CI : UK, Finland, Denmark, Norway, Sweden, Russia, Spain, Ireland, Luxemburg, Belgium, Netherland CI+ : France(Canal+), Italy(DGTVi)

DVB-C

CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria CI+ : Switzerland(UPC,Cablecom), Netherland(Ziggo), Germany(KDG,CWB), Finland(labwise)

DVB-S

CI+ : Germany(Astra HD+)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

-6-

LGE Internal Use Only

6. Component Video Input (Y, CB/PB, CR/PR)


No. Resolution 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 720x480 720x480 720x480 720x480 720x576 720x576 1280x720 1280x720 1280x720 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 15.73 15.63 31.47 31.50 15.625 31.25 45.00 44.96 45.00 31.25 33.75 33.72 56.250 67.5 Specification H-freq(kHz) V-freq(Hz) 60.00 59.94 59.94 60.00 50.00 50.00 50.00 59.94 60.00 50.00 60.00 59.94 50 60 SDTV,DVD 480i SDTV,DVD 480i 480p 480p SDTV,DVD 625 Line HDTV 576p HDTV 720p HDTV 720p HDTV 720p HDTV 1080i HDTV 1080i HDTV 1080i HDTV 1080p HDTV 1080p Remark

7. RGB (PC)
No. Resolution 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 720*400 640*480 800*600 1024*768 1280*768 1360*768 1366*768 1200*1024 1280*720 1920*1080 Specification H-freq(kHz) 31.468 31.469 37.879 48.363 47.78 47.72 47.56 63.901 45 67.5 V-freq(Hz) 70.08 59.94 60.31 60.00 59.87 59.8 59.6 60.02 60 60 Pixel Clock(MHz) 28.321 25.17 40.00 65.00 79.5 84.75 84.75 100.075 74.25 148.5 VESA VESA VESA(XGA) WXGA WXGA WXGA SXGA 720p WUXGA FHD Model WXGA Model FHD model DTV Standard FHD model For only DOS mode Input 848*480 60 Hz, 852*480 60 Hz -> 640*480 60 Hz Display Proposed Remark

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

-7-

LGE Internal Use Only

8. HDMI Input
(1) DTV Mode
No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Resolution 720*480 720*576 1280*720 1280*720 1920*1080 1920*1080 1920*1080 1920*1080 1920*1080 1920*1080 H-freq(kHz) 31.469/31.5 31.25 37.500 44.96/45 33.72/33.75 28.125 26.97/27 33.716/33.75 56.250 67.43/67.5 V-freq.(Hz) 59.94/60 50 50 59.94/60 59.94/60 50.00 23.97/24 29.976 /30.00 50 59.94/60 Pixel clock(MHz) 27.00/27.03 54 74.25 74.17/74.25 74.17/74.25 74.25 74.17/74.25 74.25 148.5 148.35/148.50 Proposed SDTV 480P SDTV 576P HDTV 720P HDTV 720P HDTV 1080I HDTV 1080I HDTV 1080P HDTV 1080P HDTV 1080P HDTV 1080P Remark

(2) PC Mode
No. 1. 2. 3. 4. 5. 6. 7. 8. 9. Resolution 720*400 640*480 800*600 1024*768 1280*768 1360*768 1280*720 1280*1024 1920*1080 H-freq(kHz) 31.468 31.469 37.879 48.363 47.78 47.72 45 63.981 67.5 V-freq.(Hz) 70.08 59.94 60.31 60.00 59.87 59.8 60 60.02 60 Pixel clock(MHz) 28.321 25.17 40.00 65.00 79.5 84.75 74.25 108.875 148.5 SXGA WUXGA VESA VESA VESA(XGA) WXGA WXGA Proposed HDCP HDCP HDCP HDCP HDCP HDCP HDCP HDCP/FHD model HDCP/FHD model Remark

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

-8-

LGE Internal Use Only

ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LCD TV with LD01U chassis.
(2) (3)

2. Designation
1) The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing. 2) Power Adjustment: Free Voltage 3) Magnetic Field Condition: Nil. 4) Input signal Unit: Product Specification Standard 5) Reserve after operation: Above 5 Minutes (Heat Run) Temperature : at 25 C 5 C Relative humidity : 65 % 10 % Input voltage : 220 V, 60 Hz 6) Adjustment equipments: Color Analyzer(CA-210 or CA-110), DDC Adjustment Jig equipment, Service remote control. 7) Push The IN STOP key - For memory initialization. Case1 : Software version up 1. After downloading S/W by USB, TV set will reboot automatically 2. Push In-stop key 3. Push Power on key 4. Function inspection 5. After function inspection, Push In-stop key. Case2 : Function check at the assembly line 1. When TV set is entering on the assembly line, Push In-stop key at first. 2. Push Power on key for turning it on. -> If you push Power on key, TV set will recover channel information by itself. 3. After function inspection, Push In-stop key.
Please Check the Speed : To use speed between from 200KHz to 400KHz

5) Click Auto tab and set as below 6) Click Run. 7) After downloading, check OK message.
(4)

filexxx.bin
(5)

(7) .OK
(6)

* USB DOWNLOAD
1) Put the USB Stick to the USB socket 2) Automatically detecting update file in USB Stick - If your downloaded program version in USB Stick is Low, it didnt work. But your downloaded version is High, USB data is automatically detecting 3) Show the message Copying files from memory

3. Main PCB check process


* APC - After Manual-Insult, executing APC

* Boot file Download


1) Execute ISP program Mstar ISP Utility and then click Config tab.
(1)
fi lexxx.bin

2) Set as below, and then click Auto Detect and check OK message If Error is displayed, Check connection between computer, jig, and set. 3) Click Read tab, and then load download file (XXXX.bin) by clicking Read 4) Click Connect tab. If Cant is displayed, check connection between computer, jig, and set.

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

-9-

LGE Internal Use Only

4) Updating is staring.

3.1. ADC Process


(1) ADC - Enter Service Mode by pushing ADJ key, - Enter Internal ADC mode by pushing G key at 5. ADC Calibration
EZ ADJUT 0. Tool Option1 1. Tool Option2 2. Tool Option3 3. Tool Option4 4. Country Group 5. ADC Calibration 6. White Balance 7. Test Pattern 8. EDID D/L 9. Sub B/C 10. V-Com 11. P-Gamma

ADC Calibration ADC Comp 480i ADC Comp 1080p ADC RGB
Start

NG NG NG
Reset

<Caution> Using power on button of the Adjustment R/C, power on TV. * ADC Calibration Protocol (RS232) Adjust Sequence aa 00 00 [Enter Adjust Mode]
Item CMD1 CMD2 Data0 Adjust Mode In A A 0 0 When transfer the Mode In, Carry the command. ADC Adjust A D 1 0 Automatically adjustment (The use of a internal pattern)

5) Uploading completed, The TV will restart automatically. 6) If your TV is turned on, check your updated version and Tool option.(explain the Tool option, next stage) * If downloading version is more high than your TV have, TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didnt have a DTV/ATV test on production line.

xb 00 40 [Component1 Input (480i)] ad 00 10 [Adjust 480i Comp1] xb 00 60 [RGB Input (1024*768)] ad 00 10 [Adjust 1024*768 RGB] aa 00 90 End Adjust mode * Required equipment : Adjustment R/C.

3.2. Function Check


* Check display and sound - Check Input and Signal items. (cf. work instructions) 1) TV 2) AV (SCART1/SCART2/CVBS) 3) COMPONENT (480i) 4) RGB (PC : 1024 x 768 @ 60 Hz) 5) HDMI 6) PC Audio In * Display and Sound check is executed by Remote control.

* After downloading, have to adjust Tool Option again.


1) Push "IN-START" key in service remote controller 2) Select Tool Option 1 and Push OK button. 3) Punch in the number. (Each model has their number)
Module AUO Tool option1 Tool option2 Tool option3 Tool option4 Tool optin5 17992 10794 51209 26904 290

4) Completed selecting Tool option.

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 10 -

LGE Internal Use Only

4. Total Assembly line process


4.1. Adjustment Preparation
W/B Equipment condition CA210 : CCFL/EEFL -> CH9, Test signal: Inner pattern(80IRE) LED -> CH14, Test signal: Inner pattern(80IRE) Above 5 minutes H/run in the inner pattern. (power on key of adjust remote control) Cool Medium Warm 13,000 9,300 6,500 K K K X=0.269(0.002) Y=0.273(0.002) X=0.285(0.002) Y=0.293(0.002) X=0.313(0.002) Y=0.329(0.002) Edge LED W/B Table is process of time (Only LGD Module) CA210: CH14, Test signal : Inner pattern(80IRE)
Aging Time GP2R (Min.) X 269 1 2 3 4 5 6 7 8 9 0-2 3-5 6-9 10-19 20-35 36-49 50-79 80-149 Over 150 279 278 277 276 274 272 271 270 269 Cool Y 273 288 286 285 283 280 277 275 274 273 Medium X 285 295 294 293 292 290 288 287 286 285 Y 293 308 306 305 303 300 297 295 294 293 X 313 319 318 317 316 314 312 311 310 309 Warm Y 329 338 336 335 333 330 327 325 324 323

Auto adjustment Map(RS-232C) RS-232C COMMAND [CMD ID DATA] Wb 00 00 White Balance Start Wb 00 ff White Balance End RS-232C COMMAND MIN [CMD ID DATA] Cool R Gain jg jh ji G Gain B Gain R Cut G Cut B Cut Mid Ja Jb Jc Warm jd je jf 00 00 00 Cool 172 172 192 64 64 64 CENTER (DEFAULT) Mid 192 192 192 64 64 64 Warm 192 192 172 64 64 64 192 192 192 128 128 128 MAX

<Test Signal> Inner pattern (204 gray, 80 IRE)

** Caution ** Color Temperature : COOL, Medium, Warm. One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0. (when R/G/B Gain are all C0, it is the FULL Dynamic Range of Module)

* Manual W/B process using adjusts Remote control.


After enter Service Mode by pushing ADJ key, Enter White Balance by pushing G key at 6. White Balance.
EZ ADJUST
0. Tool Option1 1. Tool Option2 2. Tool Option3 3. Tool Option4 4. Country Group 5. ADC Calibration 6. White Balance 7. Test Pattern 8. EDID D/L 9. Sub B/C 10. V-Com 11. P-Gamma

White Balance
Color Temp. R-Gain G-Gain B-Gain R-Cut G-Cut B-Cut Test-Pattern. Reset Cool 172 172 192 64 64 64 ON To set

* Connecting picture of the measuring instrument (On Automatic control) Inside PATTERN is used when W/B is controlled. Connect to auto controller or push Adjustment R/C POWER ON -> Enter the mode of White-Balance, the pattern will come out.

Full White Pattern

CA-210
COLOR ANALYZER TYPE: CA-210

* After you finished all adjustments, Press In-start key and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the models module from factory Jig model. * Push the IN STOP key after completing the function inspection. And Mechanical Power Switch must be set ON.

RS-232C Communication

4.2. DDC EDID Write (RGB 128Byte )


Connect D-sub Signal Cable to D-sub Jack. Write EDID Data to EEPROM(24C02) by using DDC2B protocol. Check whether written EDID data is correct or not. * For SVC main Assembly, EDID have to be downloaded to Insert Process in advance.

* Auto-control interface and directions 1) Adjust in the place where the influx of light like floodlight around is blocked. (illumination is less than 10 lux). 2) Adhere closely the Color Analyzer (CA210) to the module less than 10 cm distance, keep it with the surface of the Module and Color Analyzers prove vertically.(80 ~ 100). 3) Aging time - After aging start, keep the power on (no suspension of power supply) and heat-run over 5 minutes. - Using no signal or full white pattern or the others, check the back light on.

4.3. DDC EDID Write (HDMI 256Byte)


Connect HDMI Signal Cable to HDMI Jack. Write EDID Data to EEPROM(24C02) by using DDC2B protocol. Check whether written EDID data is correct or not. * For SVC main Assembly, EDID have to be downloaded to Insert Process in advance.
LGE Internal Use Only

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 11 -

4.4. EDID DATA


1) All Data : HEXA Value 2) Changeable Data : *: Serial No : Controlled / Data:01 **: Month : Controlled / Data:00 ***:Year : Controlled ****:Check sum
00 10 20 30 40 50 60 70 80 90 A0 B0 C0
NG NG NG NG
Reset

1) HD RGB EDID data


0 00 c 0F 01 35 6E 3E FF FF FF FF FF FF FF FF 50 01 00 28 1F FF FF FF FF FF FF FF FF 1 FF 2 FF 01 54 01 A0 55 46 FF FF FF FF FF FF FF FF 3 FF 03 A1 01 5A 00 10 FF FF FF FF FF FF FF FF 4 FF 68 08 01 00 A0 00 FF FF FF FF FF FF FF FF 5 FF 10 00 01 00 5A 0A FF FF FF FF FF FF FF FF 6 FF 09 81 1B 00 00 20 d FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 7 00 78 C0 21 1C 00 20 8 1E 0A 61 50 01 00 20 9 6D EE 40 A0 1D 1E 20 91 45 51 00 00 20 A a A3 40 00 72 00 20 54 31 1E 51 00 4C 40 30 D0 FD d 00 FF FF FF FF FF FF FF FF e FF FF FF FF FF FF FF FF B C D b 99 01 48 1E 00 26 01 88 20 3A E F

- Auto Download
After enter Service Mode by pushing ADJ key, Enter EDID D/L mode. Enter START by pushing OK key.
EZ ADJUT
0. Tool Option1 1. Tool Option2 2. Tool Option3 3. Tool Option4 4. Country Group 5. ADC Calibration 6. White Balance 7. Test Pattern 8. EDID D/L 9. Sub B/C 10. V-Com 11. P-Gamma
EDID D/L
HDMI1 HDMI2 HDMI3 RGB
Start

D0 E0 F0

2) HD HDMI EDID data


0 1 FF c 0F 01 35 6E 3E 02 22 f 00 00 A0 45 10 9E 00 5A 00 2C 50 01 00 28 1F 03 15 2 FF 01 54 01 A0 55 46 20 01 80 01 00 00 A0 25 3 FF 03 A1 01 5A 00 10 F1 26 18 1D 1E 00 5A 80 4 FF 80 08 01 00 A0 00 4E 15 71 00 8C 00 00 A0 5 FF 10 00 01 00 5A 0A 10 07 1C 80 0A 18 00 5A 6 FF 09 81 1B 00 00 20 d 1F 50 16 51 D0 02 00 00 84 09 20 D0 8A 3A 1E 00 13 57 58 0C 20 80 01 00 05 07 2C 20 E0 18 1D 9E 25 40 2D 71 80 00 00 80 10 38 D0 00 A0 35 10 2D 72 00 14 03 02 f 5A 00 3E 40 1C 00 00 A0 96 58 16 00 00 5A 00 2C 20 0e 12 7 00 78 C0 21 1C 00 20 8 1E 0A 61 50 01 00 20 9 6D EE 40 A0 1D 1E 20 91 45 51 00 00 20 A a A3 40 00 72 00 20 54 31 1E 51 00 4C 40 30 D0 FD d 01 20 e 21 B C D b 99 01 48 1E 00 26 01 88 20 3A E F 00 00

EDID D/L
HDMI1 HDMI2 HDMI3 RGB
Start

OK OK OK OK
Reset

10 20 30 40 50 60 70 80 90 A0

* Caution : Never connect HDMI & D-sub Cable when EDID download

* Edid data and Model option download (RS232)


Item Download Mode In Download A E CMD1 CMD2 Data0 A A 0 0 When transfer the Mode In, Carry the command. 00 10 Automatically Download (The use of a internal pattern)

B0 C0 D0 E0 F0

* Detail EDID Options are below Product ID Model Name HEX 0000 EDID Table 00 00 DDC Function Analog/Digital HD Model

- Manual Download
* Caution 1) Use the proper signal cable for EDID Download. - Analog EDID : Pin3 exists - Digital EDID : Pin3 exists 2) Never connect HDMI & D-sub Cable at the same time. 3) Use the proper cables below for EDID Writing. 4) Download HDMI1, HDMI2, separately because HDMI1 is different from HDMI2. For Analog EDID D-sub to D-sub For HDMI EDID DVI-D to HDMI or HDMI to HDMI

Serial No: Controlled on production line. Month, Year: Week : 01 -> 01 Year : 2011 -> 15 fix Model Name(Hex):
MODEL all MODEL NAME(HEX) 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20

Checksum: Changeable by total EDID data. Vendor Specific(HDMI)


INPUT HDMI1 HDMI2 HDMI3 MODEL NAME(HEX) 65030C001000 65030C002000 65030C003000

Item Manufacturer ID Version Revision

Condition GSM Digital : 1 Digital : 3

Data(Hex) 1E6D 01 03

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 12 -

LGE Internal Use Only

4.5. V-COM Adjust(Only LGD(M+S) Module)


- Why need Vcom adjustment? A The Vcom (Common Voltage) is a Reference Voltage of Liquid Crystal Driving. -> Liquid Crystal need for Polarity Change with every frame.
Circuit Block
Data (R ,G,B ) & Cont rol si gnal Ga mma Re f e r e nce V o ltage Data (R ,G,B ) & C ont ro l s ignal Cont rol si gnal Gamm a Reference Volta ge So urce D r i v e I C

5. Model name & Serial number D/L


Press Power on key of service remocon. (Baud rate : 115200 bps) Connect RS232 Signal Cable to RS-232 Jack. Write Serial number by use RS-232. Must check the serial number at the Diagnostics of SET UP menu. (Refer to below).

S Y S T E M
Power r I n p u t Po w e Input Da t a I n p u t

Ti m i n g Co nt r o ll e r

Po w e r Blo ck

In t e r f a ce

Column Line

V COM
CLC CST

Pane l
Liquid Crys tal

Gat e Driv e IC

V COM

Row Li ne TFT

V COM

5.1. Signal TABLE


CMD LENGTH ADH ADL DATA_1 ... Data_n CS DELAY

- Adjust sequence Press the PIP key of th ADJ remote control.(This PIP key is hot key to enter the VCOM adjuting mode) (Or After enter Service Mode by pushing ADJ key, then Enter V-Com Adjust mode by pushing G key at 10. VCom.) As pushing the right or the left key on the remote control, and find the V-COM value which is no or minimized the Flicker. (If there is no flicker at default value, Press the exit key and finish the VCOM adjustment.) Push the OK key to store value. Then the message Saing OK is pop. Press the exit key to finish VCOM adjustment.

CMD : A0h LENGTH : 85~94h (1~16 bytes) ADH : EEPROM Sub Address high (00~1F) ADL : EEPROM Sub Address low (00~FF) Data : Write data CS : CMD + LENGTH + ADH + ADL + Data_1 ++ Data_n Delay : 20ms

5.2. Command Set


No. 1 Adjust mode EEPROM WRITE CMD(hex) A0h LENGTH(hex) 84h+n Description n-bytes Write(n=1~16)

* Description FOS Default write : <7mode data> write Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0, Phase Data write : Model Name and Serial Number write in EEPROM,. (Visual Adjust and control the Voltage level)

5.3. Method & notice


A. Serial number D/L is using of scan equipment. B. Setting of scan equipment operated by Manufacturing Technology Group. C. Serial number D/L must be conformed when it is produced in production line, because serial number D/L is mandatory by D-book 4.0.

4.6. Outgoing condition Configuration


- When pressing IN-STOP key by SVC remocon, Red LED are blinked alternatively. And then Automatically turn off. (Must not AC power OFF during blinking)

4.7. Hi-pot Test


Confirm whether is normal or not when between power boards ac block and GND is impacted on 1.5 kV(dc) or 2.2 kV(dc) for one second.

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 13 -

LGE Internal Use Only

* Manual Download (Model Name and Serial Number) If the TV set is downloaded by OTA or Service man, Sometimes model name or serial number is initialized.(Not always) There is impossible to download by bar code scan, so It need Manual download. 1) Press the instart key of ADJ remote controller. 2) Go to the menu 5.Model Number D/L like below photo. 3) Input the Factory model name(ex 42LD450-ZA) or Serial

number like photo. 4) Check the model name Instart menu -> Factory name displayed (ex 42LD450-ZA) 5) Check the Diagnostics (DTV country only) -> Buyer model

=> Check the Download to CI+ Key value in LGset. 1. check the method of CI+ Key value a. check the method on Instart menu b. check the method of RS232C Command 1) into the main assy mode (RS232 : aa 00 00) CMD 1 A CMD 2 A 0 Data 0 0

2) check the key download for transmitted command (RS232 : ci 00 10) CMD 1 C CMD 2 I 1 Data 0 0

3) result value - normally status for download : OKx - abnormally status for download : NGx 2. Check the method of CI+ Key value (RS232) 1) into the main assy mode (RS232 : aa 00 00) CMD 1 A CMD 2 A 0 Data 0 0

2) Check the method of CI+ key by command (RS232 : ci 00 20) displayed (ex 42LD450) CMD 1 C CMD 2 I 2 Data 0 0

6. CI+ Key Download method


(1) Download Procedure 1) Press "Power on" button of a service remote control. (Baud rate : 115200 bps) 2) Connect RS232-C Signal Cable. 3) Write CI+ Key through RS-232-C. 4) Check whether the key was downloaded or not at In Start menu. (Refer to below).

3) Result value i 01 OK 1d1852d21c1ed5dcx CI+ key Value

7. Local Dimming Function Check


Step1) Turn on TV. Step2) Press P-only key, entrance to power only mode and Press Exit key Step3) Press Tilt key, entrance to Local Dimming mode. Step4) At the Local Dimming mode, module Edge Backlight moving right to left Back light of module moving Step5) confirm the Local Dimming mode Step6) Press Exit key

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 14 -

LGE Internal Use Only

DATA Video Audio 41P 51P 30P

Tuner_SI F

Tuner_CVBS

TUNER ( T/ C)

SCL/ SDA

FE_TS_DATA[ 0] / CLK/ Valid/ Sync

CI _TS_DATA[ 7: 0] / CLK/ Valid/ Sync CI _DATA[ 7:0] CI _ADDR[ 14:0]

PCMCIA

SYSTEM DDR3 X 16 X 1 ( 1Gb) SPI Flash( 2Mb) For FRC

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes
USB_DM/ DP HP_OUT HDMI _TMDS/ HPD/ CEC

USB

H/ P

Side
LGE101 (S7R) LGE107 (S7+URSA)
HDMI _TMDS/ HPD/ CEC HDMI _TMDS/ HPD/ CEC COMP_ YPbPr/ LR_I N AV_CVBS/ LR_I N DSUB_RGB/ HVsync DDC_SDA/ UART_TX PC_ Audio I N SPDI F_OUT SC_CVBS/ RGB/ LR_I N SC_VI DEO/ LR_OUT Debug _TX/ RX I 2S_I / F SCL/ SDA SCL/ SDA SCL/ SDA

HDMI 3

SYSTEM DDR3 X 16 X 2 ( 2Gb) SPI Flash( 8Mb)

BLOCK DIAGRAM

- 15 -

HDMI 1

HDMI 2

NAND Flash( 8Gb)

COMP1 SYSTEM EEPROM X 1 ( 1Mb) HDCP EEPROM X 1 ( 8Kb)

A/V1

PC- RGB

PC- AUDI O

SPDI F

Sub Micom ( NEC)

SCART

LGE Internal Use Only

Rear

RS-232C

Audio AMP

EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

400

521 800 540

530

810

910

LV1

550

200

120

A5 510
Copyright LG Electronics. Inc. All rights reserved. Only for training and service purposes

A10 500 A2 A21


LGE Internal Use Only

300

- 16 -

900

NAND FLASH MEMORY

IC102 NAND01GW3B2CN6E +3.3V_Normal NC_1 NC_29 NC_28 NC_27 NC_26 PCM_A[0-7] PCM_D[0-7] +3.3V_Normal

S7M-PLUS_DivX_MS10
LGE107DC-RP [S7M+ DIVX/MS10] IC101 <T3 CHIP Config(AUD_LRCH)>
AR101
I/O7 I/O6 I/O5 I/O4 NC_25 NC_24 NC_23 VDD_2 VSS_2 NC_22 R123 OPT1K R125 OPT 1K NC_21 NC_20 R115 1K R117 1K C103 0.1uF C102 10uF PCM_A[7] PCM_A[6] PCM_A[5] PCM_A[4] Boot from SPI flash : 1b0 Boot from NOR flash : 1b1 PCM_D[0] PCM_D[1] PCM_D[2] PCM_D[3] PCM_D[4] U22 T21 T22 AB18 AC18 AC19 AC20 AC21 U21 V21 Y22 AA22 R22 R21 T23 T24 AA23 Y20 AB17 AA21 U23 Y23 W23 W22 PCM_REG_N AA17 V22 W21 Y21 AA20 V23 P23 R23 P22 C108 0.1uF OPT C109 0.1uF AC17 AB20 AA18 AR103 22 AB21 AB19 AD17 AA19 22 R134 R135 R136 R137 R138 R139 22 22 22 22 22 22 M23 N23 M22 N22 A5 B5 DDCA_DA/UART0_TX DDCA_CK/UART0_RX TS1_D0 TS1_D1 PWM0 PWM1 VSS_2 NC_22 NC_21 NC_20 I/O4 I/O3 I/O2 I/O1 NC_19 NC_18 NC_17 NC_16 3D SG M_RFModule_RESET DSUB_DET MODEL_OPT_3 PCM_5V_CTL C6 B6 C8 C7 A6 SAR0/GPIO31 SAR1/GPIO32 SAR2/GPIO33 SAR3/GPIO34 SAR4/GPIO35 MPIF_D0 MPIF_D1 MPIF_D2 MPIF_D3 MPIF_BUSY E12 F12 D13 E13 MPIF_CLK MPIF_CS_N E14 D12 D14 PWM2 SC_RE2 K23 K22 G23 G22 G21 PWM0/GPIO66 PWM1/GPIO67 PWM2/GPIO68 PWM3/GPIO69 PWM4/GPIO70 TS1_D2 TS1_D3 TS1_D4 TS1_D5 TS1_D6 TS1_D7 DDCR_DA/GPIO71 DDCR_CK/GPIO72 TS1_CLK TS1_VLD TS1_SYNC AC10 AB10 AC9 AB9 AC8 AB8 AC7 AB7 FE_TS_DATA[0] FE_TS_DATA[1] FE_TS_DATA[2] FE_TS_DATA[3] FE_TS_DATA[4] FE_TS_DATA[5] FE_TS_DATA[6] FE_TS_DATA[7] UART_TX2/GPIO65 UART_RX2/GPIO64 PCM_PF_CE0Z PCM_PF_CE1Z PCM_PF_OEZ PCM_PF_WEZ PCM_PF_ALE PCM_PF_AD[15] PCM_PF_RBZ TS0_D0 TS0_D1 TS0_D2 TS0_D3 TS0_D4 TS0_D5 TS0_D6 TS0_D7 AC5 AC6 AB6 S7_NEC_TXD I/O7 I/O6 I/O5 NC_25 RGB_DDC_SDA NC_24 NC_23 VCC_2 RGB_DDC_SCL S7_NEC_RXD PCM_CE_N PCM_IRQA_N PCM_CD_N PCM_WAIT_N PCM_RESET AA9 TS0_CLK TS0_VLD TS0_SYNC AB5 AC4 Y6 AA6 W6 AA7 Y9 AA8 CI_TS_DATA[0] CI_TS_DATA[1] CI_TS_DATA[2] CI_TS_DATA[3] CI_TS_DATA[4] CI_TS_DATA[5] CI_TS_DATA[6] CI_TS_DATA[7] FE_TS_CLK FE_TS_VAL_ERR FE_TS_SYNC FE_TS_DATA[0-7] AA5 AA10 CI_TS_CLK CI_TS_VAL CI_TS_SYNC CI_TS_DATA[0-7] PM_SPI_CK/GPIO1 GPIO0/PM_SPI_CZ PM_SPI_DI/GPIO2 PM_SPI_DO/GPIO3 PCM_OE_N PCM_WE_N PCM_IORD_N PCM_IOWR_N PCM_A0 PCM_A1 PCM_A2 PCM_A3 PCM_A4 PCM_A5 PCM_A6 PCM_A7 PCM_A8 PCM_A9 PCM_A10 PCM_A11 PCM_A12 PCM_A13 PCM_A14 /PCM_REG /PCM_OE +5V_Normal /PCM_WE /PCM_IORD /PCM_IOWR R132 10K R133 10K /PCM_CE /PCM_IRQA /PCM_CD /PCM_WAIT PCM_RST AR104 /PF_CE0 /PF_CE1 /PF_OE GPIO6/PM0/INT0 GPIO7/PM1/PM_UART_TX GPIO8/PM2 GPIO9/PM3 GPIO10/PM4 GPIO11/PM5/PM_UART_RX/INT1 PM_SPI_CS1/GPIO12/PM6 PM_SPI_WP1/GPIO13/PM7 PM_SPI_WP2/GPIO14/PM8/INT2 GPIO15/PM9 PM_SPI_CS2/GPIO16/PM10 GPIO17/PM11/INT3 GPIO18/PM12/INT4 D9 D11 E10 D10 33 R151 33 R147 SPI_SCK /SPI_CS SPI_SDI SPI_SDO GPIO50/UART1_RX GPIO51/UART1_TX E7 D7 E11 G9 F9 C5 E8 E9 F7 F6 D8 G12 F10 /FLASH_WP MODEL_OPT_2 TUNER_RESET DEMOD_RESET AV_CVBS_DET 33 R146 USB1_OCD USB1_CTL HP_DET CONTROL_ATTEN MODEL_OPT_6 MODEL_OPT_1 PCM_D0 PCM_D1 PCM_D2 PCM_D3 PCM_D4 PCM_D5 PCM_D6 PCM_D7 GPIO36/UART3_RX GPIO37/UART3_TX GPIO38 GPIO39 GPIO40 GPIO41 GPIO42 F20 F19 DC_MREMOTE DD_MREMOTE 3D SG 3D SG K21 L23 K20 L20 M20 G20 G19 FRC_RESET SC1/COMP1_DET ERROR_OUT MODEL_OPT_0 M_REMOTE_RX M_REMOTE_TX 3D SG 3D SG GPIO143/TCON0 GPIO145/TCON2 GPIO147/TCON4 GPIO149/TCON6 GPIO151/TCON8 N21 M21 L22 L21 P21 5V_DET_HDMI_1 5V_DET_HDMI_2 5V_DET_HDMI_4 SIDEAV_DET

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

3.9K

1K

/PF_CE0 H : Serial Flash L : NAND Flash /PF_CE1 H : 16 bit L : 8 bit

NC_2 NC_3 NC_4 NC_5 NC_6 RB R

48 NAND_FLASH_1G_NUMONYX EAN60762401 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25

/F_RB /PF_OE

R107

R109

E /PF_CE0 R108 1K NC_7 OPT NC_8 C101 0.1uF VDD_1 VSS_1 R105 1K OPT OPT R104 10K /PF_CE1 AL PF_ALE W /PF_WE WP R106 1K C /PF_WP R102 3.3K B Q101 KRC103S OPT E NC_11 NC_12 NC_13 NC_14 NC_15 NC_9 NC_10 CL

22

<T3 CHIP Config> (AUD_SCK, AUD_MASTER_CLK, PWM1, PWM0)


PCM_A[0-14] MIPS_no_EJ_NOR8 MIPS_EJ1_NOR8 MIPS_EJ2_NOR8 B51_Secure_no scramble B51_Sesure_scramble : : : : : 4h3 4h4 4h5 4hb 4hc (MIPS (MIPS (MIPS (8051 (8051 as as as as as host. host. host. host. host. No EJ PAD. Byte mode NAND flash.) EJ use PAD1. Byte mode NAND flash.) EJ use PAD2. Byte mode NAND flash.) Internal SPI flash secure boot, no scramble) Internal SPI flash secure boot with scarmble)

PCM_D[5] PCM_D[6] PCM_D[7] PCM_A[0] PCM_A[1] PCM_A[2] PCM_A[3] PCM_A[4] PCM_A[5] PCM_A[6] PCM_A[7] PCM_A[8]

ET_RXER

+3.3V_Normal

+3.3V_Normal

AR102
I/O3 I/O2 I/O1 I/O0 NC_19 NC_18 NC_17 NC_16 PCM_A[3] PCM_A[2] PCM_A[1] PCM_A[0] C112 100pF 50V AUD_MASTER_CLK R148 56

AUD_LRCH AUD_SCK AUD_MASTER_CLK_0 PWM1 PWM0

PCM_A[9] PCM_A[10] PCM_A[11] PCM_A[12] PCM_A[13] PCM_A[14]

R116 1K OPT R118 1K OPT R121 1K

R124 1K

R126 1K

22

for SERIAL FLASH

NAND_FLASH_1G_SS NAND_FLASH_1G_HYNIX EAN35669102 IC102-*1 H27U1G8F2BTR-BC NC_1 NC_1 NC_2 NC_3 NC_4 NC_5 NC_6 R/B RE CE NC_7 NC_8 VCC_1 VSS_1 NC_9 NC_10 CLE ALE WE WP NC_11 NC_12 NC_13 NC_14 NC_15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 NC_29 NC_2 NC_28 NC_3 NC_27 NC_4 NC_26 NC_5 I/O7 NC_6 I/O6 R/B I/O5 RE I/O4 CE NC_25 NC_7 NC_24 NC_8 NC_23 VCC_1 VCC_2 VSS_1 VSS_2 NC_9 NC_22 NC_10 NC_21 CLE NC_20 ALE I/O3 WE I/O2 WP I/O1 NC_11 I/O0 NC_12 NC_19 NC_13 NC_18 NC_14 NC_17 NC_15 NC_16 EAN61857001 IC102-*2 K9F1G08U0D-SCB0

NAND_FLASH_1G_TOSHIBA EAN61508001 IC102-*3 TC58NVG0S3ETA0BBBH

from CI SLOT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25

NC_29 NC_28 NC_27 NC_26 I/O7 I/O6 I/O5 I/O4 NC_25 NC_24 NC_23 VCC_2 VSS_2 NC_22 NC_21 NC_20 I/O3 I/O2 I/O1 I/O0 NC_19 NC_18 NC_17 NC_16

NC_1 NC_2 NC_3 NC_4 NC_5 NC_6 RY/BY RE CE NC_7 NC_8 VCC_1 VSS_1 NC_9 NC_10 CLE ALE WE WP NC_11 NC_12 NC_13 NC_14 NC_15

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25

NC_29 NC_28 NC_27 NC_26 I/O8

/PF_WE PF_ALE /PF_WP /F_RB

for SYSTEM/HDCP EEPROM&URSA3

I2C_SDA I2C_SCL

Internal demod out /External demod in

TO SCART1

SC_RE1

Delete /PIF_SPI_CS
R160 1K

/RST-PHY

S7R
S7R_MS10 S7R_BASIC
IC101-*1 LGE101C-R-1 [S7R BASIC]
AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 NC_48 NC_78 NC_64 NC_50 NC_45 NC_34 NC_77 NC_65 NC_62 NC_33 NC_47 NC_46 NC_63 AC26 LVBCLKP/LLV0P/GREEN[5] LVBCLKN/LLV0N/GREEN[4] AF3 AF14 AD1 AD13 AE14 AE13 NC_44 NC_61 NC_60 NC_66 NC_76 NC_32 LVB0P/RLV6P/RED[1] LVB0N/RLV6N/RED[0] LVB1P/RLV7P/GREEN[9] LVB1N/RLV7N/GREEN[8] LVB2P/RLV8P/GREEN[7] LVB2N/RLV8N/GREEN[6] LVB3P/LLV1P/GREEN[3] LVB3N/LLV1N/GREEN[2] LVB4P/LLV0P/GREEN[1] AE4 AD5 AF4 AD4 AE2 NC_49 NC_51 NC_36 NC_67 NC_35 RLV3P/RED[7] RLV3N/RED[6] RLV0P/LVSYNC RLV0N/LHSYNC RLV1N/LCK AF8 AD9 AE9 AF9 AE11 AF6 AE6 AF11 AD6 AD12 AE5 NC_53 NC_74 NC_37 NC_43 NC_52 NC_75 NC_68 NC_59 NC_58 NC_69 TCON3/OE/GOE/GCLK2 TCON15/SCAN_BLK1 TCON18/CS7/GCLK5 TCON19/CS8/GCLK6 TCON11/CS5/HCON TCON10/CS4/OPT_N TCON9/CS3/OPT_P TCON16/WPWM TCON12/DPM TCON1/STV/GSP/VST NC_57 NC_70 NC_42 NC_38 NC_41 NC_54 NC_73 NC_39 TCON21/CS10/VGH_ODD TCON20/CS9/VGH_EVEN TCON13/LEDON TCON17/CS6/GCLK4 AB22 AB23 AC23 AC22 TCON5/TP/SOE TCON14/SACN_BLK AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 NC_57 NC_70 NC_42 NC_38 NC_41 NC_54 NC_73 NC_39 TCON21/CS10/VGH_ODD TCON20/CS9/VGH_EVEN TCON13/LEDON TCON17/CS6/GCLK4 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 NC_53 NC_74 NC_37 NC_43 NC_52 NC_75 NC_68 NC_59 NC_56 NC_72 NC_71 NC_40 RLV2P/RED[9] RLV1P/LDE RLV2N/RED[8] RLV4P/RED[5] RLV4N/RED[4] RLV5P/RED[3] RLV5N/RED[2] AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 NC_58 NC_69 TCON3/OE/GOE/GCLK2 TCON15/SCAN_BLK1 TCON18/CS7/GCLK5 TCON19/CS8/GCLK6 TCON11/CS5/HCON TCON10/CS4/OPT_N TCON9/CS3/OPT_P TCON16/WPWM TCON12/DPM TCON1/STV/GSP/VST TCON5/TP/SOE TCON14/SACN_BLK AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 NC_57 NC_70 NC_42 NC_38 NC_41 NC_54 NC_73 NC_39 TCON21/CS10/VGH_ODD TCON20/CS9/VGH_EVEN TCON13/LEDON TCON17/CS6/GCLK4 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 NC_53 NC_74 NC_37 NC_43 NC_52 NC_75 NC_68 NC_59 AE9 AF9 NC_56 NC_72 AF8 AD9 NC_71 NC_40 AE2 NC_49 LVB4N/LLV0N/GREEN[0] AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 NC_51 NC_36 NC_67 NC_35 RLV3P/RED[7] RLV3N/RED[6] RLV0P/LVSYNC RLV0N/LHSYNC RLV1N/LCK RLV2P/RED[9] RLV1P/LDE RLV2N/RED[8] RLV4P/RED[5] RLV4N/RED[4] RLV5P/RED[3] RLV5N/RED[2] AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 NC_58 NC_69 TCON3/OE/GOE/GCLK2 TCON15/SCAN_BLK1 TCON18/CS7/GCLK5 TCON19/CS8/GCLK6 TCON11/CS5/HCON TCON10/CS4/OPT_N TCON9/CS3/OPT_P TCON16/WPWM TCON12/DPM TCON1/STV/GSP/VST TCON5/TP/SOE TCON14/SACN_BLK AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 NC_57 NC_70 NC_42 NC_38 NC_41 NC_54 NC_73 NC_39 TCON21/CS10/VGH_ODD TCON20/CS9/VGH_EVEN TCON13/LEDON TCON17/CS6/GCLK4 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 NC_53 NC_74 NC_37 NC_43 NC_52 NC_75 NC_68 NC_59 AE9 AF9 NC_56 NC_72 AF8 AD9 NC_71 NC_40 AE2 NC_49 AD13 AE14 AE13 NC_44 NC_61 NC_60 AF3 AF14 AD1 NC_66 NC_76 NC_32 LVBCLKP/LLV0P/GREEN[5] LVBCLKN/LLV0N/GREEN[4] LVB0P/RLV6P/RED[1] LVB0N/RLV6N/RED[0] LVB1P/RLV7P/GREEN[9] LVB1N/RLV7N/GREEN[8] LVB2P/RLV8P/GREEN[7] LVB2N/RLV8N/GREEN[6] LVB3P/LLV1P/GREEN[3] LVB3N/LLV1N/GREEN[2] LVB4P/LLV0P/GREEN[1] LVB4N/LLV0N/GREEN[0] LVACLKP/LLV6P/BLUE[3] LVACLKN/LLV6N/BLUE[2] LVA0P/LLV3P/BLUE[9] LVA0N/LLV3N/BLUE[8] LVA1P/LLV4P/BLUE[7] LVA1N/LLV4N/BLUE[6] LVA2P/LLV5P/BLUE[5] LVA2N/LLV5N/BLUE[4] LVA3P/LLV7P/BLUE[1] LVA3N/LLV7N/BLUE[0] LVA4P/LLV8P LVA4N/LLV8N W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 NC_48 NC_78 NC_64 NC_50 NC_45 NC_34 NC_77 NC_65 NC_62 NC_33 NC_47 NC_46 NC_63 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 NC_51 NC_36 NC_67 NC_35 RLV3P/RED[7] RLV3N/RED[6] RLV0P/LVSYNC RLV0N/LHSYNC RLV1N/LCK RLV2P/RED[9] RLV1P/LDE RLV2N/RED[8] RLV4P/RED[5] RLV4N/RED[4] RLV5P/RED[3] RLV5N/RED[2] AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 NC_58 NC_69 TCON3/OE/GOE/GCLK2 TCON15/SCAN_BLK1 TCON18/CS7/GCLK5 TCON19/CS8/GCLK6 TCON11/CS5/HCON TCON10/CS4/OPT_N TCON9/CS3/OPT_P TCON16/WPWM TCON12/DPM TCON1/STV/GSP/VST TCON5/TP/SOE TCON14/SACN_BLK AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 NC_57 NC_70 NC_42 NC_38 NC_41 NC_54 NC_73 NC_39 TCON21/CS10/VGH_ODD TCON20/CS9/VGH_EVEN TCON13/LEDON TCON17/CS6/GCLK4 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 NC_53 NC_74 NC_37 NC_43 NC_52 NC_75 NC_68 NC_59 AE9 AF9 NC_56 NC_72 AF8 AD9 NC_71 NC_40 AE2 NC_49 AD13 AE14 AE13 NC_44 NC_61 NC_60 AF3 AF14 AD1 NC_66 NC_76 NC_32 LVBCLKP/LLV0P/GREEN[5] LVBCLKN/LLV0N/GREEN[4] LVB0P/RLV6P/RED[1] LVB0N/RLV6N/RED[0] LVB1P/RLV7P/GREEN[9] LVB1N/RLV7N/GREEN[8] LVB2P/RLV8P/GREEN[7] LVB2N/RLV8N/GREEN[6] LVB3P/LLV1P/GREEN[3] LVB3N/LLV1N/GREEN[2] LVB4P/LLV0P/GREEN[1] LVB4N/LLV0N/GREEN[0] LVACLKP/LLV6P/BLUE[3] LVACLKN/LLV6N/BLUE[2] LVA0P/LLV3P/BLUE[9] LVA0N/LLV3N/BLUE[8] LVA1P/LLV4P/BLUE[7] LVA1N/LLV4N/BLUE[6] LVA2P/LLV5P/BLUE[5] LVA2N/LLV5N/BLUE[4] LVA3P/LLV7P/BLUE[1] LVA3N/LLV7N/BLUE[0] LVA4P/LLV8P LVA4N/LLV8N

S7MR
S7R_DivX
IC101-*3 LGE101DC-R-1 [S7R DIVX]
W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 NC_48 NC_78 NC_64 NC_50 NC_45 NC_34 NC_77 NC_65 NC_62 NC_33 NC_47 NC_46 NC_63 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 NC_51 NC_36 NC_67 NC_35 RLV3P/RED[7] RLV3N/RED[6] RLV0P/LVSYNC RLV0N/LHSYNC RLV1N/LCK RLV2P/RED[9] RLV1P/LDE RLV2N/RED[8] RLV4P/RED[5] RLV4N/RED[4] RLV5P/RED[3] RLV5N/RED[2] AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 NC_58 NC_69 TCON3/OE/GOE/GCLK2 TCON15/SCAN_BLK1 TCON18/CS7/GCLK5 TCON19/CS8/GCLK6 TCON11/CS5/HCON TCON10/CS4/OPT_N TCON9/CS3/OPT_P TCON16/WPWM TCON12/DPM TCON1/STV/GSP/VST TCON5/TP/SOE TCON14/SACN_BLK AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 AE9 AF9 NC_56 NC_72 AF8 AD9 NC_71 NC_40 AE2 NC_49 AD13 AE14 AE13 NC_44 NC_61 NC_60 AF3 AF14 AD1 NC_66 NC_76 NC_32 LVBCLKP/LLV0P/GREEN[5] LVBCLKN/LLV0N/GREEN[4] LVB0P/RLV6P/RED[1] LVB0N/RLV6N/RED[0] LVB1P/RLV7P/GREEN[9] LVB1N/RLV7N/GREEN[8] LVB2P/RLV8P/GREEN[7] LVB2N/RLV8N/GREEN[6] LVB3P/LLV1P/GREEN[3] LVB3N/LLV1N/GREEN[2] LVB4P/LLV0P/GREEN[1] LVB4N/LLV0N/GREEN[0] LVACLKP/LLV6P/BLUE[3] LVACLKN/LLV6N/BLUE[2] LVA0P/LLV3P/BLUE[9] LVA0N/LLV3N/BLUE[8] LVA1P/LLV4P/BLUE[7] LVA1N/LLV4N/BLUE[6] LVA2P/LLV5P/BLUE[5] LVA2N/LLV5N/BLUE[4] LVA3P/LLV7P/BLUE[1] LVA3N/LLV7N/BLUE[0] LVA4P/LLV8P LVA4N/LLV8N W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 NC_48 NC_78 NC_64 NC_50 NC_45 NC_34 NC_77 NC_65 NC_62 NC_33 NC_47 NC_46 NC_63 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 NC_51 NC_36 NC_67 NC_35 RLV3P/RED[7] RLV3N/RED[6] RLV0P/LVSYNC RLV0N/LHSYNC RLV1N/LCK RLV2P/RED[9] RLV1P/LDE RLV2N/RED[8] RLV4P/RED[5] RLV4N/RED[4] RLV5P/RED[3] RLV5N/RED[2] AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 AF8 AD9 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 AE2 FRC_DDR3_RESETB/DDR2_A3 AD13 AE14 AE13 NC_44 NC_61 NC_60 AF3 AF14 AD1 NC_66 NC_76 NC_32 LVBCLKP/LLV0P/GREEN[5] LVBCLKN/LLV0N/GREEN[4] LVB0P/RLV6P/RED[1] LVB0N/RLV6N/RED[0] LVB1P/RLV7P/GREEN[9] LVB1N/RLV7N/GREEN[8] LVB2P/RLV8P/GREEN[7] LVB2N/RLV8N/GREEN[6] LVB3P/LLV1P/GREEN[3] LVB3N/LLV1N/GREEN[2] LVB4P/LLV0P/GREEN[1] LVB4N/LLV0N/GREEN[0] LVACLKP/LLV6P/BLUE[3] LVACLKN/LLV6N/BLUE[2] LVA0P/LLV3P/BLUE[9] LVA0N/LLV3N/BLUE[8] LVA1P/LLV4P/BLUE[7] LVA1N/LLV4N/BLUE[6] LVA2P/LLV5P/BLUE[5] LVA2N/LLV5N/BLUE[4] LVA3P/LLV7P/BLUE[1] LVA3N/LLV7N/BLUE[0] LVA4P/LLV8P LVA4N/LLV8N

S7R_DivX_MS10 S7R_RM S7MR_BASIC


IC101-*6 LGE107C-R-1 [S7MR BASIC]
W26 NC_48 NC_78 NC_64 NC_50 NC_45 NC_34 NC_77 NC_65 NC_62 NC_33 NC_47 NC_46 NC_63 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 AF8 AD9 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 AE2 FRC_DDR3_RESETB/DDR2_A3 AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ AF3 AF14 AD1 FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] B4M/TCON8/BLUE[6] LVACLKP/LLV6P/BLUE[3] LVACLKN/LLV6N/BLUE[2] LVA0P/LLV3P/BLUE[9] LVA0N/LLV3N/BLUE[8] LVA1P/LLV4P/BLUE[7] LVA1N/LLV4N/BLUE[6] LVA2P/LLV5P/BLUE[5] LVA2N/LLV5N/BLUE[4] LVA3P/LLV7P/BLUE[1] LVA3N/LLV7N/BLUE[0] LVA4P/LLV8P LVA4N/LLV8N W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 AF8 AD9 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 AE2 FRC_DDR3_RESETB/DDR2_A3 AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ AF3 AF14 AD1 FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] B4M/TCON8/BLUE[6] ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8] W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 AF8 AD9 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 AE2 FRC_DDR3_RESETB/DDR2_A3 AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ AF3 AF14 AD1 FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] B4M/TCON8/BLUE[6] ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8]

S7MR_MS10
IC101-*7 LGE107C-R [S7MR MS10]
W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16

S7MR_DivX
IC101-*8 LGE107DC-R-1 [S7MR DIVX]
W26 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8] W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24

S7MR_DivX_MS10
IC101-*9 LGE107DC-R [S7MR DIVX/MS10]
AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 AC26 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] AF3 AF14 AD1 AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] AE4 AD5 AF4 AD4 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 AE9 AF9 AF8 AD9 AE2 B4M/TCON8/BLUE[6] AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 AD13 AE14 AE13 AF3 AF14 AD1 ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8] W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16

S7MR_RM
IC101-*10 LGE107RC-R [S7MR RM]
W26 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 AC26 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] B0P/RLV6P/GREEN[7] FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] B4M/TCON8/BLUE[6] FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 FRC_DDR3_RESETB/DDR2_A3 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8] W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24

IC101-*2 LGE101C-R [S7R MS10]

IC101-*4 LGE101DC-R [S7R DIVX/MS10]


W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16

IC101-*5 LGE101RC-R [S7R RM]

URSA_DEBUG P3904 12505WS-03A00

FRC_SCL FRC_SDA

3 4

EEPROM_1MBIT_ATMEL

AF12 AF5 AE12

IC104-*1 AT24C1024BN-SH-T
IC103-*1 CAT24C08WI-GT3-H-RECV(TV)
NC
NC_1 1 8 VCC

AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8

AB16 NC_26

AB16 NC_26 NC_19 NC_30 AA14 AC15 Y16 NC_15 AE8 NC_55 Y11 Y19 NC_12 GND_105 NC_21 NC_20 Y10 NC_11 NC_17 AA11 AB15 NC_25 NC_24 AB14 NC_25 NC_24 NC_11 NC_17 NC_31 NC_29 AA16 AA15 Y11 Y19 NC_12 GND_105 NC_21 NC_20 AC16 AC14 AE8 NC_55 NC_15 NC_31 NC_29 NC_26 NC_19 NC_30

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 NC_25 NC_24 NC_11 NC_17 AE8 NC_55 Y11 Y19 NC_12 GND_105 NC_21 NC_20 NC_15 NC_31 NC_29 NC_26 NC_19 NC_30

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 NC_25 NC_24 NC_11 NC_17 AE8 NC_55 Y11 Y19 NC_12 GND_105 NC_21 NC_20 NC_15 NC_31 NC_29 NC_26 NC_19 NC_30

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 FRC_PWM0 FRC_PWM1 FRC_I2CS_DA FRC_I2CS_CK AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_REXT FRC_TESTPIN FRC_I2CM_DA FRC_I2CM_CK FRC_GPIO8 FRC_GPIO9/UART_TX FRC_GPIO10 FRC_GPIO0/UART_RX FRC_GPIO1 FRC_GPIO3

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 FRC_PWM0 FRC_PWM1 FRC_I2CS_DA FRC_I2CS_CK AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_REXT FRC_TESTPIN FRC_I2CM_DA FRC_I2CM_CK FRC_GPIO8 FRC_GPIO9/UART_TX FRC_GPIO10 FRC_GPIO0/UART_RX FRC_GPIO1 FRC_GPIO3

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 FRC_PWM0 FRC_PWM1 FRC_I2CS_DA FRC_I2CS_CK AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_REXT FRC_TESTPIN FRC_I2CM_DA FRC_I2CM_CK FRC_GPIO8 FRC_GPIO9/UART_TX FRC_GPIO10 FRC_GPIO0/UART_RX FRC_GPIO1 FRC_GPIO3

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 FRC_PWM0 FRC_PWM1 FRC_I2CS_DA FRC_I2CS_CK AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_REXT FRC_TESTPIN FRC_I2CM_DA FRC_I2CM_CK FRC_GPIO8 FRC_GPIO9/UART_TX FRC_GPIO10 FRC_GPIO0/UART_RX FRC_GPIO1 FRC_GPIO3

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 FRC_PWM0 FRC_PWM1 FRC_I2CS_DA FRC_I2CS_CK AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_REXT FRC_TESTPIN FRC_I2CM_DA FRC_I2CM_CK FRC_GPIO8 FRC_GPIO9/UART_TX FRC_GPIO10 FRC_GPIO0/UART_RX FRC_GPIO1 FRC_GPIO3

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14

VCC
AE8 NC_55 Y11 NC_12 GND_105

AA14 AC15 Y16

NC_19 NC_30 NC_15 NC_31 NC_29

AC16 AC14 AA16

A1
NC_2 2 7 WP

WP

Y19

NC_21 NC_20

AA15 Y10

NC_11 NC_17

AA11 AB15

NC_25 NC_24

AB14

A2
A2 3 6 SCL

SCL

GND
VSS 4 5 SDA

SDA

S7MR-PLUS
S7M-PLUS_BASIC
IC101-*11 LGE107C-RP-1 [S7M+ BASIC]

I2C
S7M-PLUS_DivX
IC101-*13 LGE107DC-RP-1 [S7M+ DIVX]
W26 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 AC26 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 AC26 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] AF3 AF14 AD1 AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] AE4 AD5 AD23 AF4 AD4 AE2 FRC_DDR3_RESETB/DDR2_A3 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] AF8 AD9 AE9 AF9 AE11 AF6 AD19 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 AE10 AF7 AD11 AD7 AB22 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 AF8 AD9 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 AE2 FRC_DDR3_RESETB/DDR2_A3 B4M/TCON8/BLUE[6] AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AF4 AD4 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ AF3 AF14 AD1 FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] B4M/TCON8/BLUE[6] ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8] W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 AC26 AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8]

HDCP_EEPROM_ON_SEMI_NEW

S7M-PLUS_MS10
IC101-*12 LGE107C-RP [S7M+ MS10]
AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8]

S7M-PLUS_RM
IC101-*14 LGE107RC-RP [S7M+ RM]
W26 W25 U26 U25 U24 V26 V25 V24

+3.3V_Normal

DIMMING
R140 1K R141 1K R142 3.3K R143 3.3K R144 2.2K
W24 Y26 Y25 Y24

+3.3V_Normal

AE1 AF16 AF1 AE3 AD14 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8]

W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24

W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24

HDCP EEPROM

+3.3V_Normal

AE15 AD2 AD16 AD15 AE16

R145 2.2K

Addr:10101--

AD3 AF15

EEPROM
EEPROM_1MBIT_ST

AF2

AC26 BCKP/TCON13/GREEN[1] AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 AE4 AD5 AD23 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] FRC_DDR3_RESETB/DDR2_A3 C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] AF8 AD9 AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 AE6 AF11 AD6 AD12 AE5 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 AE10 AF7 AD11 AD7 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 AE11 AF6 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 AF8 AD9 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 AE2 FRC_DDR3_RESETB/DDR2_A3 AF4 AD4 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ AF3 AF14 AD1 FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] B4M/TCON8/BLUE[6]

AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24

R156 A_DIM R157 PWM_DIM AMP_SDA AMP_SCL I2C_SDA I2C_SCL NEC_SDA NEC_SCL SCAN_BLK2 C111 2.2uF R155 0

HDCP_EEPROM_CATALYST_OLD
IC103 CAT24WC08W-T

R113 4.7K

A0 A1 A2 VSS

1 2 3 4

8 7 6 5

VCC WP SCL SDA

C107 0.1uF R127 4.7K R128 22 I2C_SCL

IC104 M24M01-HRMN6TP
NC VCC

C105 0.1uF

BCKM/TCON12/GREEN[0] AF3 AF14 AD1 AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] AE4 AD5 AF4 AD4 AE2 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 B4M/TCON8/BLUE[6]

10K 100

PWM0 PWM2

AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22

$0.199

OPT

E1

WP

AE11 AF6

AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18

LD650 Scan
R158 R159 SCAN_BLK1/OPC_OUT 100 OPT 100 OPT FRC_PWM1 FRC_PWM0

E2

A0h

SCL

AF12

R111 R112 C104 8pF OPT C106 8pF OPT

22 22

AF5

I2C_SCL I2C_SDA

AE12

R129

22

I2C_SDA
VSS 4 5 SDA

AD10 AE7 AF10 AD8

AB23 AC23 AC22

AB16 FRC_SPI_CZ FRC_GPIO1 FRC_SPI1_CK Y16 FRC_GPIO8 AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_VSYNC_LIKE FRC_TESTPIN FRC_SPI_CK FRC_SPI_DI Y10 FRC_I2CS_DA FRC_I2CS_CK AB15 FRC_PWM0 FRC_PWM1 AB14 FRC_PWM0 FRC_PWM1 AA11 FRC_I2CS_DA FRC_I2CS_CK FRC_SPI_DO FRC_SPI1_DI AA16 AA15 Y11 Y19 FRC_VSYNC_LIKE FRC_TESTPIN FRC_SPI_CK FRC_SPI_DI AC16 AC14 AE8 FRC_DDR3_NC/DDR2_DQM0 FRC_GPIO8 FRC_SPI_DO FRC_SPI1_DI AA14 AC15 FRC_SPI_CZ FRC_GPIO1 FRC_SPI1_CK

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 FRC_PWM0 FRC_PWM1 FRC_I2CS_DA FRC_I2CS_CK AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_VSYNC_LIKE FRC_TESTPIN FRC_SPI_CK FRC_SPI_DI FRC_GPIO8 FRC_SPI_DO FRC_SPI1_DI FRC_SPI_CZ FRC_GPIO1 FRC_SPI1_CK

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14 FRC_PWM0 FRC_PWM1 FRC_I2CS_DA FRC_I2CS_CK AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_VSYNC_LIKE FRC_TESTPIN FRC_SPI_CK FRC_SPI_DI FRC_GPIO8 FRC_SPI_DO FRC_SPI1_DI FRC_SPI_CZ FRC_GPIO1 FRC_SPI1_CK

AB16 AA14 AC15 Y16 AC16 AC14 AA16 AA15 Y10 AA11 AB15 AB14

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP3_Saturn7M
FLASH/EEPROM/GPIO

Ver. 0.1 1

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

+3.3V_Normal

RSDS Power OPT


MODEL OPTION MODEL OPTION
VDD_RSDS:88mA HIGH FRC_HW_OPT NO_FRC U3_INTERNAL U5_EXTERNALBOOT reserved for FRC OPT L213 BLM18PG121SN1D L214 BLM18PG121SN1D FRC C4005 0.1uF VDD_RSDS

+1.26V_VDDC

VDDC 1.26V
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 10uF

+1.26V_VDDC VDDC : 2026mA

100/120Hz LVDS R294 1K

1K

DVB_T2 R208 1K

PHM_ON R211 1K

FRC_H/W_OPT R226 1K

1K

1K

PIN NAME MODEL_OPT_0 MODEL_OPT_4 MODEL_OPT_1 MODEL_OPT_0 MODEL_OPT_1 MODEL_OPT_2 MODEL_OPT_3 MODEL_OPT_4 MODEL_OPT_5 MODEL_OPT_6 MODEL_OPT_6 MODEL_OPT_3 MODEL_OPT_5 MODEL_OPT_2

PIN NO. G19 E18 C5 F7 B6 D18 F9

LOW NO FRC

OPT R214

OPT R295

C275

C228

C276

C4006

C4011

C4013

C4019

C277

C280

C283

C292

IF_AGC_SEL LNA2_CTL RF_SWITCH_CTL

OPT 100 R201 R202 BOOSTER_OPT 100 R203 RF_SW_OPT 100 R204 R210 100 OPT 100 OPT 0 3D_SG 3D_SG 0

PHM_OFF NON_DVB_T2 HD Ready LCD

PHM_ON DVB_T2 FHD default OLED

--> This option is only applied in EU. In case of NON_EU, default value set LOW.

C299

50/60Hz LVDS

100/120Hz LVDS

VDD33

OPT

OPT

C4024

: LOW : HIGH :HIGH : LOW

LOW LOW HIGH HIGH

+2.5V_Normal

FHD R206

10uF

OPT_0 OPT_4

OPT

OPT

3D_GPIO_1 3D_GPIO_2

R213 R216

-->In case of GP2, This port was used for GIP/NON_GIP

LGE107DC-RP +1.26V_VDDC

S7M-PLUS_DivX_MS10 IC101 [S7M+ DIVX/MS10]


G18 VDDC_1 VDDC_2 VDDC_3 VDDC_4 VDDC_5 VDDC_6 VDDC_7 VDDC_8 VDDC_9 VDDC_10 VDDC_11 GND_1 GND_2 GND_3 GND_4 GND_5 GND_6 GND_7 GND_8 GND_9 GND_10 GND_11 GND_12 A_DVDD B_DVDD GND_13 GND_14 GND_15 FRC_VDDC_0 FRC_VDDC_1 FRC_VDDC_2 FRC_VDDC_3 FRC_VDDC_4 FRC_VDDC_5 FRC_VDDC_6 FRC_VDDC_7 FRC_VDDC_8 GND_16 GND_17 GND_18 GND_19 GND_20 GND_21 GND_22 GND_23 GND_24 GND_25 U3_DVDD_DDR GND_26 GND_27 GND_28 AVDD1P2 DVDD_NODIE GND_29 GND_30 GND_31 GND_32 AVDD2P5_ADC_1 AVDD2P5_ADC_2 AVDD25_REF GND_33 GND_34 GND_35 GND_36 GND_37 AVDD_AU25 GND_38 GND_39 GND_40 PVDD_1 PVDD_2 GND_41 GND_42 GND_43 AVDD25_PGA GND_44 GND_45 GND_46 AVDD_NODIE GND_47 GND_48 GND_49 AVDD_DVI_1 AVDD_DVI_2 AVDD3P3_CVBS AVDD_DMPLL GND_50 GND_51 GND_52 GND_53 GND_54 GND_55 AVDD_AU33 AVDD_EAR33 GND_56 GND_57 GND_58 GND_59 AVDD33_T GND_60 GND_61 VDDP_1 VDDP_2 VDDP_3 GND_62 GND_63 GND_64 GND_65 GND_66 FRC_VD33_2_1 FRC_VD33_2_2 GND_67 GND_68 GND_69 FRC_AVDD_RSDS_1 FRC_AVDD_RSDS_2 FRC_AVDD_RSDS_3 GND_70 GND_71 GND_72 GND_73 FRC_AVDD FRC_AVDD_LPLL FRC_AVDD_MPLL GND_74 GND_75 GND_76 GND_77 FRC_VDD33_DDR GND_78 GND_79 GND_80 H9 H10 H18 H19 J10 J17 J18 J19 K9 K10 K11 K12 K13 K14 K15 K16 K17 K18 L9 L10 L11 L12 L13 L14 L15 L16 L17 M9 M10 M11 M12 M13 M14 M15 M16 M17 N10 N11 N12 N13 N14 N15 N16 N17 P10 P11 P12 P13 P14 P15 P16 P17 R10 R11 R12 R13 R14 R15 R16 R17 R18 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 U10 U11 U12 U13 U14 U15 U16 U17 V7 V8 V9 V10 V11 V12 V13 V14 V15 V16 V17 V18 W7 W8 W9 W10 W11 W12 W13 W16 W17 W18 Y13 Y18 AA13 AB13 AC13 D17 H23 AF13 J9 L223 U9 BLM18SG121TN1D

50/60Hz LVDS R297 1K

1K

NON_DVB_T2 R209 1K

PHM_OFF R212 1K

R293 OPT 1K

NO_FRC R227 1K

1K

--> MODEL_OPT_5, MODEL_OPT_6 : Only 3D_SG GPIO OUTPUT CONTROL

Normal Power 3.3V


+3.3V_Normal VDD33 VDD33_T/VDDP/U3_VD33_2:47mA H11 H12 L204 BLM18PG121SN1D 0.1uF C284 10uF C293 10uF H13 H14 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C4001 10uF 0.1uF H15 J12 J13 J14 J15 J16 L18 AVDD_MEMPLL:24mA VDD33 AU33:31mA AU33 FRC_AVDD:60mA +2.5V_Normal FRC_AVDD H16 K19 L19 0.1uF M18 M19 N18 N19 N20 P18 P19 P20 Y12

OPT R215

HD R207

Close to MSTAR

DTV_IF
IF_P_MSTAR IF_N_MSTAR TU_SIF 1000pF OPT C264

C4007

C4012

C4014

C4020

C4043

C4044

OPT

C250 C251

0.1uF R4002 0.1uF R4003

47 47

OPT

OPT

OPT

F1 CK+_HDMI1 CK-_HDMI1 D0+_HDMI1 D0-_HDMI1 D1+_HDMI1 D1-_HDMI1 D2+_HDMI1 D2-_HDMI1 DDC_SDA_1 DDC_SCL_1 HPD1 CK+_HDMI2 CK-_HDMI2 D0+_HDMI2 D0-_HDMI2 D1+_HDMI2 D1-_HDMI2 D2+_HDMI2 D2-_HDMI2 DDC_SDA_2 DDC_SCL_2 HPD2 CK+_HDMI4 CK-_HDMI4 D0+_HDMI4 D0-_HDMI4 D1+_HDMI4 D1-_HDMI4 D2+_HDMI4 D2-_HDMI4 DDC_SDA_4 DDC_SCL_4 HPD4 F2 G2 G3 H3 G1 H1 H2 F5 F4 E6 D3 C1 D1 D2 E2 E3 F3 E1 D4 E4 D5 AA2 AA1 AB1 AA3 AB3 AB2 AC2 AC1 AB4 AA4 AC3 A2 A3 B3 A1 B1 B2 C2 C3 B4 C4 E5 CEC_REMOTE_S7 D6 D_RXCP D_RXCN D_RX0P D_RX0N D_RX1P D_RX1N D_RX2P D_RX2N DDCDD_DA/GPIO30 DDCDD_CK/GPIO29 HOTPLUGD/GPIO22 CEC/GPIO5 LINE_IN_0L DSUB_HSYNC DSUB_VSYNC DSUB_R+ DSUB_G+ DSUB_B+ 10K R4026 R4023 10K R4024 22 R4025 22 R228 R229 R230 R231 R232 R233 33 68 33 68 33 68 C204 C205 C206 C207 C208 C209 C210 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 1000pF G5 G6 K1 L3 K3 K2 J3 J2 J1 HSYNC0 VSYNC0 RIN0P RIN0M GIN0P GIN0M BIN0P BIN0M SOGIN0 LINE_IN_0R LINE_IN_1L LINE_IN_1R LINE_IN_2L LINE_IN_2R LINE_IN_3L LINE_IN_3R LINE_IN_4L LINE_IN_4R LINE_IN_5L LINE_IN_5R G4 H6 R253 R254 R255 R256 R257 R258 R236 NON_EU H5 R237 R238 R239 R240 R241 R242 33 68 33 68 33 68 C218 C219 C220 C221 C222 C223 C224 C248 R244 R245 R246 R4016 R248 R249 R250 C203 1000pF OPT DTV/MNT_VOUT R252 68 C233 0.047uF R251 33 33 33 33 33 33 33 33 C225 C226 C227 C229 C230 C231 C232 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 1000pF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF N4 N6 L4 L5 L6 M4 M5 K7 M6 M7 N5 VCOM0 CVBS_OUT1 CVBS_OUT2 CVBS0P CVBS1P CVBS2P CVBS3P CVBS4P CVBS5P CVBS6P CVBS7P ET_REFCLK ET_TX_EN ET_MDC ET_MDIO ET_CRS TP210 ET_RXD1 ET_TXD1 ET_RXD0 ET_TXD0 N3 N2 M2 M1 L2 L1 M3 HSYNC2 RIN2P RIN2M GIN2P GIN2M BIN2P BIN2M SOGIN2 HP_OUT_1L HP_OUT_1R VAG VRP VRM AUCOM 33 68 33 68 33 68 0 C211 C212 C213 C214 C215 C216 C217 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 1000pF K5 K4 J4 K6 H4 J6 J5 HSYNC1 VSYNC1 RIN1P RIN1M GIN1P GIN1M BIN1P BIN1M SOGIN1 MIC_DET_IN MICCM MICIN LINE_OUT_0L LINE_OUT_2L LINE_OUT_3L LINE_OUT_0R LINE_OUT_2R LINE_OUT_3R I2S_OUT_BCK/GPIO181 I2S_OUT_MCK/GPIO179 I2S_OUT_SD/GPIO182 I2S_OUT_SD1/GPIO183 I2S_OUT_SD2/GPIO184 I2S_OUT_SD3/GPIO185 I2S_OUT_WS/GPIO180 C_RXCP C_RXCN C_RX0P C_RX0N C_RX1P C_RX1N C_RX2P C_RX2N DDCDC_DA/GPIO28 DDCDC_CK/GPIO27 HOTPLUGC/GPIO21 I2S_IN_BCK/GPIO175 I2S_IN_SD/GPIO176 I2S_IN_WS/GPIO174 DM_P1 DP_P1 DM_P0 DP_P0 SPDIF_IN/GPIO177 SPDIF_OUT/GPIO178 B_RXCP B_RXCN B_RX0P B_RX0N B_RX1P B_RX1N B_RX2P B_RX2N DDCDB_DA/GPIO26 DDCDB_CK/GPIO25 HOTPLUGB/GPIO20 XTALIN XTALOUT TGPIO0/UPGAIN TGPIO1/DNGAIN TGPIO2/I2C_CLK TGPIO3/I2C_SDA IFAGC RF_TAGC A_RXCP A_RXCN A_RX0P A_RX0N A_RX1P A_RX1N A_RX2P A_RX2N DDCDA_DA/GPIO24 DDCDA_CK/GPIO23 HOTPLUGA/GPIO19 QP QM SSIF/SIFP SSIF/SIFM IP IM VIFP VIFM

W2 W1

TP201 TP202

ANALOG SIF Close to MSTAR

C4025

C4031

S7M-PLUS_DivX_MS10 IC101 LGE107DC-RP [S7M+ DIVX/MS10]

R288 R289

100 100

C257 C258

0.1uF 0.1uF

0.1uF

MIU0VDDC MIU1VDDC

V2 V1 +3.3V_Normal Y2 Y1 U3 V3 Y5 Y4 TP205 U1 U2 R3 T3 T2 R287 T1 1M X201 24MHz C261 27pF FULL_NIM R291 FULL_NIM R292 AMP_SCL AMP_SDA 22 22 TP203 TP204 C4064 0.1uF L227 BLM18PG121SN1D 0.1uF L215 BLM18PG121SN1D C4015 0.1uF OPT L221 BLM18PG121SN1D FRC

C4023

R4019 1K

Close to MSTAR
R4020 10K IF_AGC_MAIN VDD33 C4065 0.022uF 16V

FRC_LPLL:13mA FRC_LPLL

FRC_MPLL:4mA

FRC_VDD33_DDR:50mA VDD33 FRC_VDD33_DDR FRC L222 BLM18PG121SN1D

0.1uF

DEMOD_SCL DEMOD_SDA TU_SCL TU_SDA

0.1uF

0.1uF

TU/DEMOD_I2C

L206 BLM18PG121SN1D

C4040

FRCVDDC

FRC C4016 C4041 OPT C286 C4045 1uF

J11 L7

VDD33_DVI:163mA VDD33_DVI +3.3V_Normal C262 27pF LED_DRIVER_D/L_SDA L207 BLM18PG121SN1D 0.1uF C4002 0.1uF C4008 C287 10uF

AVDD2P5 AVDD_DMPLL L217 BLM18PG121SN1D 0.1uF C4017 0.1uF C288 0.1uF AU25

H7 J7 J8

HDMI

G14 G13 R296 100

SPDIF_OUT

B/T USB
B7 A7 AF17 AE17

C294

L8

OPT AVDD_DMPLL/AVDD_NODIE:7.362mA SIDE_USB_DM SIDE_USB_DP

AVDD2P5 AVDD2P5 AVDD25_PGA

W15 Y15 U8

SIDE USB
F14 F13 F15 D20 E20 D19 F18 E18 D18 E19 MODEL_OPT_4 MODEL_OPT_5 AUD_LRCK AVDD_DMPLL NEC_SDA COMP2_DET NEC_SCL AUD_SCK AUD_MASTER_CLK_0 AUD_LRCH LED_DRIVER_D/L_SCL VDD33_DVI M8

Normal 2.5V
I2S_I/F
AVDD2P5/ADC2P5:162mA +2.5V_Normal AVDD2P5 AVDD2P5 AVDD2P5 AVDD_DMPLL L211 BLM18PG121SN1D 0.1uF 0.1uF C289 10uF

N9 P9 N8 P8

AU33

T7 U7

C4026

C295

N1 P3 P1 P2 P4 P5 R6 T6 U5 V5 U6 V6

C236 C237 C238 C239 C4059 C4060 C242 C243 C244 C245 C246 C247

2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF OPT 2.2uF OPT

VDD33

SC1/COMP1_L_IN SC1/COMP1_R_IN

T9 R8

AUDIO IN

AV_L_IN AV_R_IN SIDEAV_L_IN SIDEAV_R_IN COMP2_L_IN COMP2_R_IN PC_L_IN PC_R_IN

+2.5V_Normal

AU25

+2.5V_Normal

AVDD25_PGA

R9 T8

DSUB

L212 BLM18PG121SN1D 0.1uF

L219 BLM18PG121SN1D 0.1uF V20 W20 VDD_RSDS U19 U20 V19

AU25:10mA

AVDD25_PGA:13mA

SCART1_RGB/COMP1
SC1_ID SC1_FB SC1_R+/COMP1_Pr+ SC1_G+/COMP1_Y+ SC1_B+/COMP1_Pb+ SC1_SOG_IN

U4 W3 W4 V4 Y3 W5 R4 TP209 TP207 TP208 SCART1_Rout SCART1_Lout

C296

C4027

FRC_AVDD FRC_LPLL

W19 U18 T20 Y14

BLM18PG121SN1D

AUDIO OUT

DDR3 1.5V
+1.5V_DDR AVDD_DDR0 AVDD_DDR0:55mA C4046 0.1uF AVDD_DDR0 AVDD_DDR1:55mA AVDD_DDR0 VDD33

FRC_VDD33_DDR

0.1uF

L209

T5 C234 OPT 2.2uF R5 C235 2.2uF OPT T4 L202 BLM18SG121TN1D P7 R7 P6 CM2012F5R6KT 5.6uH R1 L203 R2 L205 5.6uH C268 4.7uF C272 4.7uF HEAD_PHONE HEAD_PHONE E21 E22 D21 F21 E23 D22 F22 D23 F23 CM2012F5R6KT HEAD_PHONE C249 4.7uF C253 1uF C256 0.1uF C263 10uF

R19 W14 AVDD_MEMPLL FRC_AVDD_MEMPLL

GND_81 GND_82 GND_83 GND_84 GND_85 AVDD_DDR0_D_1 AVDD_DDR0_D_2 AVDD_DDR0_D_3 AVDD_DDR0_D_4 AVDD_DDR0_C GND_86 GND_87 GND_88 GND_89 GND_90 GND_91 AVDD_DDR1_D_1 AVDD_DDR1_D_2 AVDD_DDR1_D_3 AVDD_DDR1_D_4 AVDD_DDR1_C GND_92 GND_93 GND_94 GND_95 GND_96 GND_97 GND_98 FRC_AVDD_DDR_D_1 FRC_AVDD_DDR_D_2 FRC_AVDD_DDR_D_3 FRC_AVDD_DDR_D_4 FRC_AVDD_DDR_C GND_99 GND_100 GND_101 GND_102 GND_103 GND_104 GND_105 GND_106 GND_107 MVREF GND_108 GND_109 GND_110 NC_1 NC_2 GND_FU PGA_VCOM

COMP2

C285

COMP2_Pr+ COMP2_Y+ COMP2_Pb+

C4018

0.1uF

0.1uF

C4003

0.1uF

C4009

0.1uF

C4028

0.1uF

C4032

0.1uF

C4038

C4036

C4042

0.1uF

0.1uF

0.1uF

OPT C290 10uF

C297

C4022

C278

C281

AVDD_DDR0

D15 D16 E15 E16 E17

10uF

10uF

OPT

OPT

10uF

OPT

OPT

OPT

H/P OUT
HP_LOUT HP_ROUT FRC L210 +1.5V_FRC_DDR

BLM18PG121SN1D

AVDD_DDR0 AVDD_DDR0 AVDD_DDR_FRC:55mA R4014 1K 1/16W 1% AVDD_DDR_FRC MVREF

F16 F17 G16 G17 H17

TU_CVBS SC1_CVBS_IN

CVBS In/OUT

AV_CVBS_IN SIDEAV_CVBS_IN

C4057 0.047uF

ET_RXD0 ET_TXD0 ET_RXD1 ET_TXD1 ET_REF_CLK ET_TX_EN ET_MDC ET_MDIO ET_CRS


TP206 R298 OPT 100 IR

HEAD_PHONE

FRC

FRC

FRC

OPT

C4004 OPT

0.1uF C240 FRC

0.1uF R4015 1K

1/16W 1%

0.1uF

0.1uF

0.1uF

0.1uF

Delete CHB_CVBS_IN
AV_CVBS_IN2

C4010 FRC

10uF

10uF

C241

AVDD_DDR_FRC

AB11 AB12 AC11 AC12 AA12

C279

C282

RSDS Power OPT


+1.26V_VDDC MIU0VDDC +1.26V_VDDC FRCVDDC FRC L225 BLM18SG700TN1D 0.1uF C4061 10uF MVREF G15

Close to MSTAR
F8 AVLINK IRINT TESTPIN AV_CVBS_IN2 TP211 RESET U3_RESET FRC R4017 22 G8 K8 C4066 10uF A4 Y17 FRC R205 10K +3.3V_Normal R4006 10K SOC_RESET L226 BLM18SG700TN1D C4063 10uF MIU1VDDC 0.1uF L228 BLM18SG700TN1D

C291

C298

0.1uF

Y7 Y8

C4062

FRC_RESET

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

OPT

C4056

R4018 10K

C4058

FRC

FRC

GP2R MAIN2, HW OPT

20101023 2

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

EAN61829001

EAN61857101

IC301-*2 H5TQ1G63DFR-PBC
FRC_DDR_1600_HYNIX N3 P7 P3 N2 P8 P2 R8 R2 VCC1.5V_U3_DDR T8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 C324 10uF 10V C325 0.1uF 16V M7 A15 M2 BA0 BA1 BA2 J7 K7 K9 VCC1.5V_U3_DDR VCC1.5V_U3_DDR L2 K1 J3 R301 1K 1% R304 1K 1% K3 L3 T2 RESET CS ODT RAS CAS WE 0.1uF 1000pF C-MVREFCA CK CK CKE VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 NC_1 NC_2 NC_3 AR301 C-MA9 C-MA2 C-MA0 C-MBA2 C-TMA9 C-TMA2 C-TMA0 C-TMBA2 22 AR302 C-MA8 C-MA6 C-MA4 EAN61828901 C-MBA1 22 AR303 C-MA10 C-TMA10 C-TMA12 C-TMA1 C-TMA11 22 AR304 C-MA3 C-MA5 C-MA7 C-MRESETB 22 R307 C-MCK 22 R308 C-MCKB 22 R309 M7 NC_5 M2 BA0 BA1 A1 A8 C1 C9 D2 E9 F1 H2 H9 J1 J9 L1 L9 T7 NC_1 NC_2 NC_3 NC_4 NC_6 DQSL DQSL A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 B1 B9 D1 D8 E2 E8 F9 G1 G9 VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 DQL7 D7 C3 C8 C2 A7 A2 B8 A3 DML DMU E3 F7 F2 F8 H3 H8 G2 H7 DQSU DQSU E7 D3 C7 B7 F3 G3 C-MDQSL C-MDQSLB C-MDQSU C-MDQSUB C-MDML C-MDMU C-MDQL0 C-MDQL1 C-MDQL2 C-MDQL3 C-MDQL4 C-MDQL5 C-MDQL6 C-MDQL7 C-MDQU0 C-MDQU1 C-MDQU2 C-MDQU3 C-MDQU4 C-MDQU5 C-MDQU6 C-MDQU7 C-MDQU7 C-MDQU1 C-MDQU5 C-MDQU3 22 C-MDQU2 C-MDQU6 C-MDQU0 C-MDQU4 22 AR309 C-TMDQU7 C-TMDQU1 C-TMDQU5 C-TMDQU3 R317-*1 4.7K S7M-PLUS Y10 FRC_I2CS_DA FRC_I2CS_CK AB15 FRC_PWM0 FRC_PWM1 AB14 FRC_PWM0 FRC_PWM1 R334 OPT 22 FRC_SDA +3.3V_Normal AA11 R326 22 R331 22 R335 OPT FRC FRC 22 I2C_SDA I2C_SCL FRC_SCL C-MDQL5 22 AR308 C-TMDQU2 C-TMDQU6 C-TMDQU0 C-TMDQU4 V_SYNC Y16 FRC_L/DIM 33 R332 R317 820 S7M-R FRC_GPIO8 AE8 FRC_DDR3_NC/DDR2_DQM0 Y11 Y19 FRC_VSYNC_LIKE FRC_TESTPIN FRC_SPI_CK FRC_SPI_DI FRC_SPI_DO FRC_SPI1_DI AA16 AA15 FRC_SPI_SCK FRC_SPI_SDI AC16 AC14 FRC_CONF1 R348 33 FRC_L/DIM FRC_SPI_SDO L/DIM_MOSI C-MDQL0 C-MDQL2 C-MDQL6 C-MDQL4 22 R316 C-TMDQL5 FRC_SPI_CZ FRC_GPIO1 FRC_SPI1_CK RESET VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 CS ODT RAS CAS WE T2 CK CK CKE L2 K1 J3 K3 L3 C-MDQSL C-MODT C-MRASB C-MCASB C-MWEB VCC1.5V_U3_DDR R333 10K C-MDQSLB 22 R313 C-MDQSU 22 R314 C-MDQSUB 22 R315 C-MDMU 22 AR306 C-MDQL7 C-MDQL3 C-MDQL1 C-MDML 22 AR307 C-TMDQL0 C-TMDQL2 C-TMDQL6 C-TMDQL4 AB16 AA14 AC15 FRC_/SPI_CS C-TMDQL7 C-TMDQL3 C-TMDQL1 C-TMDML C-TMDQU0 C-TMDQU1 C-TMDQU2 C-TMDQU3 C-TMDQU4 C-TMDQU5 C-TMDQU6 C-TMDQU7 C-TMDMU C-TMDQSUB C-TMDQSU 22 R312 C-TMDQSLB C-TMDQL0 C-TMDQL1 C-TMDQL2 C-TMDQL3 C-TMDQL4 C-TMDQL5 C-TMDQL6 C-TMDQL7 AE6 AF11 AD6 AD12 AE5 AF12 AF5 AE12 AE10 AF7 AD11 AD7 AD10 AE7 AF10 AD8 FRC_DDR3_DQU0/DDR2_DQ8 FRC_DDR3_DQU1/DDR2_DQ14 FRC_DDR3_DQU2/DDR2_DQ13 FRC_DDR3_DQU3/DDR2_DQ12 FRC_DDR3_DQU4/DDR2_DQ15 FRC_DDR3_DQU5/DDR2_DQ9 FRC_DDR3_DQU6/DDR2_DQ10 FRC_DDR3_DQU7/DDR2_DQM1 GPIO0/TCON15/HSYNC/VDD_ODD GPIO1/TCON14/VSYNC/VDD_EVEN GPIO2/TCON7/LDE/GCLK4 GPIO3/TCON6/LCK/GCLK2 AB22 AB23 AC23 AC22 FRC_MODEL_OPT_0 FRC_MODEL_OPT_1 FRC_MODEL_OPT_2 2D/3D_CTL FRC_DDR3_DQL0/DDR2_DQ6 FRC_DDR3_DQL1/DDR2_DQ0 FRC_DDR3_DQL2/DDR2_DQ1 FRC_DDR3_DQL3/DDR2_DQ2 FRC_DDR3_DQL4/DDR2_DQ4 FRC_DDR3_DQL5/DDR2_NC FRC_DDR3_DQL6/DDR2_DQ3 FRC_DDR3_DQL7/DDR2_DQ5 BA2 J7 K7 K9 N8 M3 C-MBA0 C-MBA1 C-MBA2 C-MCK OPT R306 150 C-MCASB C-MODT C-MWEB C-MCKB C-MCKE C-MBA0 22 R311 C-TMDQSL C-TMDML C-TMDMU AE11 AF6 FRC_DDR3_DML/DDR2_DQ7 FRC_DDR3_DMU/DDR2_DQ11 DCKP/TCON5 DCKM/TCON4 D0P/LLV6P D0M/LLV6N D1P/LLV7P D1M/LLV7N D2P/LLV8P D2M/LLV8N D3P/TCON3 D3M/TCON2 D4P/TCON1 D4M/TCON0 AD19 AE19 AD21 AE21 AF21 AD20 AE20 AF20 AF19 AD18 AE18 AF18 RXDCK+ R342 1K RXD0+ RXD0RXD1+ RXD1RXD2+ RXD2RXD3+ RXD3R341 1K R339 1K RXD4OPT RXD4+ R343 1K R337 1K OPT RXDCKC-MRASB 22 AR305 C-TMCASB C-TMODT C-TMWEB C-TMBA0 C-TMDQSU C-TMDQSUB AE9 AF9 FRC_DDR3_DQSU/DDR2_DQS1 FRC_DDR3_DQSUB/DDR2_DQSB1 C-TMDQSL C-TMDQSLB AF8 AD9 FRC_DDR3_DQSL/DDR2_DQS0 FRC_DDR3_DQSLB/DDR2_DQSB0 C-MCKE 22 R310 C-TMRASB C-TMRESETB C-TMCKE C-TMCKB C-TMODT C-TMRASB C-TMCASB C-TMWEB C-TMCK AE4 AD5 AF4 AD4 AE2 FRC_DDR3_RESETB/DDR2_A3 FRC_DDR3_ODT/DDR2_BA1 FRC_DDR3_RASZ/DDR2_WEZ FRC_DDR3_CASZ/DDR2_CKE FRC_DDR3_WEZ/DDR2_BA0 CCKP/LLV3P CCKM/LLV3N C0P/LLV0P/BLUE[5] C0M/LLV0N/BLUE[4] C1P/LLV1P/BLUE[3] C1M/LLV1N/BLUE[2] C2P/LLV2P/BLUE[1] C2M/LLV2N/BLUE[0] C3P/LLV4P C3M/LLV4N C4P/LLV5P C4M/LLV5N AD23 AE23 AE26 AE25 AF26 AF25 AE24 AF24 AF23 AD22 AE22 AF22 RXCCK+ RXCCKRXC0+ RXC0RXC1+ RXC1RXC2+ RXC2RXC3+ RXC3RXC4+ RXC4L/DIM_EDGE_32/37 +3.3V_Normal C-TMA3 C-TMA5 C-TMA7 C-TMRESETB C-TMCK C-TMCKE C-TMCKB AD13 AE14 AE13 FRC_DDR3_MCLK/DDR2_MCLK FRC_DDR3_CKE/DDR2_RASZ FRC_DDR3_MCLKZ/DDR2_MCLKZ C-TMBA0 C-TMBA1 C-TMBA2 AF3 AF14 AD1 FRC_DDR3_BA0/DDR2_BA2 FRC_DDR3_BA1/DDR2_ODT FRC_DDR3_BA2/DDR2_A12 AC26 BCKP/TCON13/GREEN[1] BCKM/TCON12/GREEN[0] B0P/RLV6P/GREEN[7] B0M/RLV6N/GREEN[6] B1P/RLV7P/GREEN[5] B1M/RLV7N/GREEN[4] B2P/RLV8P/GREEN[3] B2M/RLV8N/GREEN[2] B3P/TCON11/BLUE[9] B3M/TCON10/BLUE[8] B4P/TCON9/BLUE[7] B4M/TCON8/BLUE[6] AC25 AA26 AA25 AA24 AB26 AB25 AB24 AC24 AD26 AD25 AD24 RXACK+ RXACKRXA0+ RXA0RXA1+ RXA1RXA2+ RXA2RXA3+ RXA3RXA4+ RXA4D7 C3 C8 C2 A7 A2 B8 A3 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 C-MA12 C-MA0 C-MA1 C-MA2 C-MA3 C-MA4 C-MA5 C-MA6 C-MA7 C-MA8 C-MA9 C-MA10 C-MA11 C-MA12 C-MA1 C-MA11 C-TMA8 C-TMA6 C-TMA4 C-TMBA1 C-TMA0 C-TMA1 C-TMA2 C-TMA3 C-TMA4 C-TMA5 C-TMA6 C-TMA7 C-TMA8 C-TMA9 C-TMA10 C-TMA11 C-TMA12 AE1 AF16 AF1 AE3 AD14 AD3 AF15 AF2 AE15 AD2 AD16 AD15 AE16 FRC_DDR3_A0/DDR2_NC FRC_DDR3_A1/DDR2_A6 FRC_DDR3_A2/DDR2_A7 FRC_DDR3_A3/DDR2_A1 FRC_DDR3_A4/DDR2_CASZ FRC_DDR3_A5/DDR2_A10 FRC_DDR3_A6/DDR2_A0 FRC_DDR3_A7/DDR2_A5 FRC_DDR3_A8/DDR2_A2 FRC_DDR3_A9/DDR2_A9 FRC_DDR3_A10/DDR2_A11 FRC_DDR3_A11/DDR2_A4 FRC_DDR3_A12/DDR2_A8 ACKP/RLV3P/RED[3] ACKM/RLV3N/RED[2] A0P/RLV0P/RED[9] A0M/RLV0N/RED[8] A1P/RLV1P/RED[7] A1M/RLV1N/RED[6] A2P/RLV2P/RED[5] A2M/RLV2N/RED[4] A3P/RLV4P/RED[1] A3M/RLV4N/RED[0] A4P/RLV5P/GREEN[9] A4M/RLV5N/GREEN[8] W26 W25 U26 U25 U24 V26 V25 V24 W24 Y26 Y25 Y24 F3 RXBCK+ RXBCKRXB0+ RXB0RXB1+ RXB1RXB2+ RXB2RXB3+ RXB3RXB4+ RXB4E3 F7 F2 F8 H3 H8 G2 H7 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 E7 D3 DML DMU C7 B7 DQSU DQSU VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 G3 DQSL DQSL A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 C7 B7 E7 D3 E3 F7 F2 F8 H3 H8 G2 H7 D7 C3 C8 C2 A7 A2 B8 A3 NC_4 NC_6 J9 L1 L9 T7 F3 G3 A1 A8 C1 C9 D2 E9 F1 H2 H9 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 ZQ L8 VREFDQ H1 VREFCA M8 N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3 M7

IC301-*3 K4B1G1646G-BCH9
FRC_DDR_1333_SS_NEW M8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 NC_5 M2 N8 M3 J7 K7 K9 L2 K1 J3 K3 L3 T2 RESET CS ODT RAS CAS WE NC_1 NC_2 NC_3 NC_4 DQSL DQSL A9 DQSU DQSU DML DMU DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 D7 C3 C8 C2 A7 A2 B8 A3 VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 E3 F7 F2 F8 H3 H8 G2 H7 E7 D3 C7 B7 NC_6 CK CK CKE BA0 BA1 BA2 VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 J9 L1 L9 T7 F3 G3 T2 A1 A8 C1 C9 D2 E9 F1 H2 H9 L2 K1 J3 K3 L3 J7 K7 K9 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 M2 N8 M3 M7 ZQ L8 VREFDQ H1 VREFCA N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

EAN61857201

IC301-*4 NT5CB64M16DP-CF
FRC_DDR_1333_NANYA_NEW M8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 NC_6 NC_5 BA0 BA1 BA2 VDDQ_1 CK CK CKE CS ODT RAS CAS WE NC_1 RESET NC_2 NC_3 NC_4 DQSL DQSL A9 DQSU DQSU DML DMU DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 NC_7 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 J9 L1 L9 T7 A1 A8 C1 C9 D2 E9 F1 H2 H9 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 ZQ L8 VREFDQ H1 VREFCA

DDR3 1.5V By CAP - Place these Caps near Memory


+1.5V_FRC_DDR

VCC1.5V_U3_DDR

R3 L7 R7 N7 T3

L301 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C315 0.1uF C316 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C303 C305 C306 C307 C308 C309 C310 C311 C313 C317 C318 C319 C320 C321 C322 C323 0.1uF C301 10uF

OPT

Close to DDR Power Pin

N8 M3

S7M-PLUS_DivX_MS10 IC101 LGE107DC-RP [S7M+ DIVX/MS10]

0.1uF

1000pF

C-MVREFDQ R305 1%

R302

1%

C302

C304

1K

CLose to DDR3

CLose to Saturn7M IC

IC301 H5TQ1G63DFR-H9C FRC_DDR_1333_HYNIX


C-MVREFCA M8 VREFCA A0 A1 C-MVREFDQ R303 240 1% B2 D9 G7 K2 K8 N1 N9 R1 VCC1.5V_U3_DDR R9 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 H1 VREFDQ A2 A3 A4 L8 ZQ A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

C312

C314

1K

<U3 CHIP Config> (FRC_CONF0)


HIGH : I2C ADR = B8 LOW : I2C ADR = B4

R340 LVDS_EXT_URSA5 1K R338 OPT 1K

R336 1K

C-MRESETB

(FRC_CONF1,FRC_PWM1, FRC_PWM0)
FRC_MODEL_OPT_0 FRC_MODEL_OPT_1 FRC_MODEL_OPT_2 3d5 : boot from internal SRAM 3d6 : boot from EEPROM 3d7 : boot form SPI flash

L/DIM_EDGE_42/47/55

2D/3D_CTL

+3.3V_Normal

R320 FRC 1K R321 1K

LVDS_S7M-PLUS

S7M-PLUS

FRC

R322 OPT1K

R323 1K

FRC_CONF0 FRC_CONF1 FRC_PWM1 FRC_PWM0

R319 OPT1K R325 1K

R324 OPT 1K

R300 33 FRC_L/DIM

L/DIM_SCLK

+3.3V_Normal S7M-PLUS_S_FLASH_2MBIT_WIN R349 S7M-PLUS 10K R350 4.7K

R344 0 3D_SYNC_RF 3D_SG FRC_/SPI_CS

IC302 W25X20BVSNIG
CS VCC

S7M-PLUS R329 10 R330 10

OPT

$ 0.17

DO

FRC_SPI_SDO

HOLD S7M-PLUS R328 10 FRC_SPI_SCK DIO R327 10 S7M-PLUS FRC_SPI_SDI

S7M-PLUS WP 3 6 CLK

GND

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R FRC_DDR

S7M-R

R318 FRC 1K

FRC_CONF0

20101023 3

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

+12V/+15V

ST_3.5V--> 3.375V --> 3.46V 20V-->3.51V --> 3.76V (3.59V)

L412

FROM LIPS & POWER B/D


+3.5V_ST

PANEL_POWER
R405-*1 3K C438 0.1uF 16V C442 10uF 16V OPT New item Q409 AO3407A S D PANEL_VCC C443 10uF 25V G C451 0.1uF 50V 1608 OPT C B C Q406 2SC3052 E R435 22K Q407 2SC3052 E C455 0.1uF 16V R405 2.2K R407 2.2K R407-*1 3K

+12V/+15V

24V-->3.78V --> 3.92V (3.79V) 12V -->3.58V --> 3.82V (3.68V) 18.5V-->3.5V --> 3.75V (3.59V) PD_+12V 1% R448 2.7K

+3.5V_ST

+3.5V_ST -> 3.375V +3.5V_ST R488 100K IC408 NCP803SN293 VCC RESET R402 100 POWER_DET OPT R463 10K 2 1 GND PWR_DET_ON_SEMI C474 0.1uF PD_+12V RESET R480 100

0.015uF

RT1P141C-T112 Q402 R439 33K

R406 4.7K RL_ON R401 10K C B Q401 2SC3052 E L404-*1 CIS21J121

1 2

3 NORMAL_EXPEPT_32 P403 FW20020-24S NORMAL_32 P404 FM20020-24 L407-*1 CIS21J121 +24V

C411 0.1uF 16V

1/10W 1% PD_+12V

0.01uF C409 C436 0.015uF 0.01uF 50V 25V

PANEL_DISCHARGE_RES PANEL_DISCHARGE_RES R447 1.21K

PD_+3.5V 5%

R450 0

R440 5.6K

R431 22K PWR ON 1 24V 3 GND 5 7 9 11 13 15 17 19 21 23 GND 3.5V 3.5V 2 4 6 8 10 12 14 16 18 20 22 24 24V 24V GND GND 3.5V 3.5V GND GND/V-sync INV ON A.DIM P.DIM1 Err OUT POWER_16_GND POWER_18_INV_CTL R415 100 R425 100 R419 1K +3.5V_ST +3.3V_Normal PANEL_CTL 1:AK10 C418 0.1uF 50V C426 68uF 35V L407 MLB-201209-0120P-N2 OPT R430 10K

+24V

R404 100K IC409

PD_+12V

R482 8.2K

1%

POWER_+24V

NCP803SN293 VCC

+3.5V_ST

L404 MLB-201209-0120P-N2

3 1 GND

R403 1.5K

C401 100uF 16V

C406 0.1uF 16V

C408 0.1uF 16V OPT

R429 47K B

OPT OPT

GND GND 12V 12V 12V

C412 0.1uF 16V PD_+12V

POWER_+24V

1%

PD_+12V_PWR_DET_ON_SEMI

Power_DET S7M DDR 1.5V


POWER_ON/OFF1 10K R464

+12V/+15V L402 MLB-201209-0120P-N2 C402 100uF 16V C404 0.1uF 16V L402-*1 CIS21J121 C407 0.1uF 16V OPT R476 0

GND/P.DIM2

25 POWER_23_GND SLIM_32~52 P401 SMAW200-H24S2

R412

R426 10K R421 10K

OPT

1074 mA
+12V/+15V

+3.3V_Normal
IC405 AOZ1073AIL-3 L416 1934 mA
L421 3.6uH NR8040T3R6N 1% 2 7 R460 27K VIN C492 0.1uF AGND 16V C457 10uF 25V C459 10uF 25V LX_1 PGND 1 8 LX_2

+3.3V_Normal

POWER_24_GND R475 0

C R418 POWER_24_INV_CTL 6.8K OPT E

INV_CTL +3.5V_ST EP[GND]

C475 0.1uF 16V

Q405 2SC3052 POWER_18_A_DIM 0 R451 POWER_22_A_DIM R485 0

R427 10K OPT

C462 0.1uF 16V

+1.5V_DDR

L424 CIC21J501NE

VIN_3

PWRGD

POWER_24_PWM_DIM R472 0

R484 0

PWM_DIM C461 10uF 10V R606-*1 1K PWM_PULL-DOWN_1K C468 0.1uF 16V VIN_2 GND_1 GND_2

1 2 3 4 THERMAL 17

12 11

R456 10K FB 4 5 COMP 12K R454 2200pF C464

PH_2 PH_1 SS/TR C465 0.01uF 50V R452 1/16W 330K 5% R455 15K

NR8040T3R6N C472 22uF 10V C476 22uF 10V 47K 1% C463 100pF 50V C470 0.1uF 16V

R471 0 PWM_PULL-DOWN_3.9K POWER_22_PWM_DIM R606 3.9K C416 OPT 0.1uF 16V

10 IC407 TPS54319TRE 9

OPT C423 100pF 50V

R457

R462 10K

VSENSE

COMP

RT/CLK

AGND

R1

1%

1%

VIN_1

PH_3

R461 4.7K

POWER_20_A_DIM 0 POWER_20_PWM_DIM R453

A_DIM 16 15 14 13

EN

L420

BOOT

L423 3.6uH

3A

EN

POWER_ON/OFF2_2

R1

C469 22uF 16V

C473 0.1uF 16V

C485 0.1uF 16V

R2

+3.3V_Normal POWER_20_ERROR_OUT OPT R437 100 R486 4.7K

C467 4700pF 50V

Vout=(1+R1/R2)*0.8
R2
R449 56K 1/16W

POWER_24_ERROR_OUT R420 100

ERROR_OUT

1/16W

5%

<MODULE PIN MAP> PIN No LGD(PSU) or LIPS 16 18 20 22 24 23 GND INV_ON


VBR-A
CMO10"Lamp AUO 10"Lamp

1% 3A $ 0.145 Vout=0.827*(1+R1/R2)=1.521V

+5V_Normal
+12V/+15V

(PSU) GND A-DIM NC

(PSU) GND INV_ON Err_out NC

SHARP (PSU) GND INV_ON


52/60:ERROR 26/32HD:NC 26/32/52:PWM

IPS-@ (PSU) GND INV_ON Err_out NC PWM_DIM GND

TP5302

OLP

IC406 AOZ1072AI-3
PGND LX_2 L422 3.6uH NR8040T3R6N

MAX 1A

TP5303 TP5304 TP5305 TP5306

V_SYNC SCAN_BLK2 SCAN_BLK1/OPC_OUT +3.3V_Normal OPC_OUT IC402 AZ2940D-2.5TRE1 VIN VOUT R473

L417

+2.5V/+1.8V
+2.5V_Normal 1 Vd=550mV3 2 C432 0.1uF 16V GND

PWM_DIM PWM_DIM

Err_out INV_ON PWM_DIM GND GND GND

26/32/52:GND 60:PWM

C458 10uF 25V

C460 10uF 25V

R459 10K FB 4 5 COMP 12K R458 2200pF C466

R466 51K

1%

60:NC

300 mA

C490 0.1uF AGND 16V

2A

EN

POWER_ON/OFF2_2

1%

R465 24K

VIN

LX_1

R1

C471 22uF 16V

C477 0.1uF 16V

GND

OPT C427 100pF 50V

R467 10K

C403 10uF 10V

<LED MODULE PIN MAP -> latest update 20100618> PIN No 16 18 20 22 24 23 LGD LPB/ OS LPB NC INV_ON NC PWM_DIM
32LE5300-TA CMO10"LED 32LE4500-TA AUO 10"LED 32LE5300-TA LGD 10"LED

<Module Inv to Main Pin Connection>

1%

C440 0.1uF 16V

(PSU) NC

(PSU) NC

(PSU) NC INV_ON NC PWM_DIM err_out --> NC NC

INV_ON INV_ON err_out err_out --> NC --> NC NC NC

INV #11 #12 #13 #14

<--> <--> <--> <--> <-->

MAIN #24 #18 #20 #22

Vout=0.8*(1+R1/R2)

R2

+5V_TUNER IC410 AP1117EG-13

+5V_Normal

IC411 AP1117EG-13

IN

OUT R422 1 5% 110 R417 C414 0.1uF 16V C415 10uF 10V C422 0.1uF 50V

IN

OUT R424 1 5% 330 R409 110 R408 C417 0.1uF 16V C419 10uF 10V

err_out --> NC PWM_DIM PWM_DIM NC NC NC

ADJ/GND

ADJ/GND

S7M core 1.26V volt


POWER_ON/OFF2_1 10K R445 C447 +5V_USB +3.5V_ST EP[GND] 0.1uF 16V C441 0.1uF VIN_3 PWRGD BOOT 16V +1.26V_VDDC

C491 0.1uF 50V

330 R411

LGD edge led error-out use or not? checking is necessary...

+5V_USB
+12V/+15V

C421,C422 Close to LDO

L401

EN

IC401 AOZ1073AIL-3
PGND LX_2 L406 3.6uH NR8040T3R6N C489 0.1uF 16V AGND C405 10uF 25V C410 10uF 25V 1% 2 7 R414 51K VIN LX_1

2000 mA

L413

VIN_1 C430 10uF 10V VIN_2 C431 0.1uF 16V GND_1 GND_2

1 2 3 4 THERMAL 17

12 11

PH_3 PH_2 PH_1 SS C488 0.01uF 50V R432 1/16W 330K 5% R436 7.5K C448 3300pF 50V

L415 3.6uH NR8040T3R6N C453 22uF 10V C456 22uF 10V C444 0.1uF 16V

16

15

14

13

+1.5V_DDR Q408 AO3438 FRC D S

+1.5V_FRC_DDR

R416 1.5K

R410 10K FB 4 5 COMP 12K R413 2200pF C413

VSENSE

COMP

RT/CLK

AGND

R423 10K

1/16W 1%

5%

R2
R441 75K 1/8W 1%

R444

R1

50V 100pF C439

R443 FRC 10K

OPT

C435 4.7uF 10V

POWER_ON/OFF2_1

R2
R434 120K

4A Vout=(1+R1/R2)*0.8

$ 0.165

Vout=0.8*(1+R1/R2)=1.29V

OPT

+1.5V_DDR_FRC
GP2R POWER_LARGE 20101023 4

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

C445

1%

R1

4.7uF OPT

3A

EN

POWER_ON/OFF2_1

OPT C429 100pF 50V

C420 22uF 16V

C424 0.1uF 16V

C428 0.1uF 16V OPT

22K 1% 24K 1%

R442

10 IC403 SN1007054RTER 9

LGE Internal Use Only

CRYSTAL_KDS X1002-*1 FLMD0 32.768KHz

S/T_SCL 15pF 10K 15pF

S/T_SDA

C1007

C1008

R1030

X1002 32.768KHz

MICOM_RESET

NEW_SUB R4034 4.7K NEW_SUB R4035 4.7K

+3.5V_ST

CRYSTAL_EPSON R1034 4.7M CRYSTAL_KDS

+3.5V_ST NEW_SUB 22 R1043 47K NEW_SUB R1046 TP1601 C1010 0.1uF TP1602

R1091 10K

for Debugger
MICOM_DEBUG_WAFER

GND

P122/X2/EXCLK/OCD0B

P1001
12505WS-12A00

R1039

P120/INTP0/EXLVI

+3.5V_ST
0.1uF

P124/XT2/EXCLKS

22

R1060

22

NEC_ISP_Tx

NEC_ISP_Rx C1003 0.1uF

P123/XT1

MICOM_DEBUG R1078 22 MICOM_DEBUG R1010 22 MICOM_DEBUG R1081 22 MICOM_DEBUG R1013 22

C1006

MICOM_DEBUG R1076 22

MICOM_RESET

+3.5V_ST

P121/X1/OCD0A

+3.5V_ST

TOP SIDE for reset.

R1047

20K

FLMD0

OCD1A

R1089 20K

VDD

VSS

P40

P41

1/16W 1%

RESET

1/16W 1% EDID_WP C B Q1001 2SC3052 E

OCD1B

10

11

FLMD0

48

47

46

45

44

43

42

41

40

39

38

13

37

12

MICOM_DEBUG R1002 10K R1018 R1019 22 22

REGC

P60/SCL0 P61/SDA0 P62/EXSCL0 P63 P33/TI51/TO51/INTP4

NEC_SCL NEC_SDA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 NEC_MICOM

36 35 34 33 32 31 30 29 28 27 26 25

P140/PCL/INTP6 P00/TI000 P01/TI010/TO00

R1048 R1049

22 22

RL_ON

+3.5V_ST

OPT R1006 OPT R1072 OPT R1073 OPT R1005 10K 10K 10K 10K

NEC CONFIGURATION
+3.5V_ST NEC_ISP_Tx OPT R1084 10K OCD1A POWER_ON/OFF2_1 NEC_EEPROM_SDA R1020 CEC_REMOTE_NEC R1065 22 0 NEC_EEPROM_SCL

OPT R1050 10K R1090 OPT R1055 R1056 R1057 22 22 22 SCART1_MUTE CEC_ON/OFF (MODEL_OPT_3) MODEL1_OPT_2 POWER_ON/OFF1

P130 P20/ANI0 ANI1/P21 ANI2/P22 ANI3/P23 ANI4/P24 ANI5/P25 ANI6/P26 ANI7/P27

22

NEC_ISP_Rx

IC1002
uPD78F0514

P75 P74 P73/KR3 P72/KR2 P71/KR1 P70/KR0 P32/INTP3/OCD1B

OCD1B

AMP_MUTE R1066 AMP_RESET (MODEL_OPT_0) SOC_RESET INV_CTL R1023 22 22

R1054 R1052

22 10K

19-22_LAMP OLP SIDE_HP_MUTE KEY2 KEY1

EEPROM for Micom


+3.5V_ST
PANEL_CTL (MODEL_OPT_1)

R1063

22

IC1001
M24C16-WMN6T

IC1001-*1 AT24C16BN-SH-B
NC_1 VCC

OCD1B

NC/E0 R1001 47K

P16/TOH1/INTP5

P31/INTP2/OCD1A

P10/SCK10/TXD0

P17/TI50/TO50

P11/SL10/RXD0

P30/INTP1

P15/TOH0

P14/RXD6

P13/TXD6

P12/SO10

R1014 2.7K

R1015 2.7K

C1002

0.1uF

NC_2

NC/E1
TP1001

WC

WP

AVREF

AVSS

VCC

NC_3 NEC_EEPROM_SCL

NC/E2

SCL

TP1002

R1080 22

SCL

+3.5V_ST

GND NEC_EEPROM_SDA

VSS

SDA

TP1003

R1008 22

SDA

EEPROM_NEC_16KBIT_ATMEL EEPROM_NEC_16KBIT_STM

22

22

+3.5V_ST

MICOM MODEL OPTION


GP2 R1079 10K

+3.5V_ST PWM_BUZZ/IIC_LED R1009 10K

TOUCH_KEY R1075 10K

B/L_LED R1071 10K

22

R1069

AMP_RESET PANEL_CTL CEC_ON/OFF

MODEL_OPT_0 MODEL_OPT_1 MODEL1_OPT_2 MODEL_OPT_3

R1068

22

R1037

R1041

R1083

10K OPT

LED_B/LG_LOGO

PWM_LED R1004 10K

LED_R/BUZZ

GP3 R1074 10K

TACT_KEY R1011 10K

B/L_LAMP R1012 10K

NEC_ISP_Rx

NEC_ISP_Tx

POWER_DET

IR

POWER_ON/OFF2_2

S7_NEC_RXD

S7_NEC_TXD

OCD1A

C1009 1uF

2011Y,GP2R, 101125 Update


MODEL OPTION
MODEL_OPT_0 PIN NAME MODEL_OPT_0 MODEL_OPT_1 MODEL_OPT_2 MODEL_OPT_3 PIN NO. 8 11 30 31 HIGH B/L_LED PWM_BUZZ/IIC_LED TOUCH_KEY GP2 LOW LOW B/L_LAMP LOW PWM_LED TACT_KEY HIGH GP3 Low PWM_BUZZ/IIC_LED :Using IIC for LED Breathing & PWM Buzz PWM_LED : Using PWM Signal for LED Lighting HIGH LOW LOW LOW TBD IIC LED(09Y IIC Protocol) & No BUZZ TBD S/T & IIC LED & No Buzz & LED Blink MODEL_OPT_3 LOW : LED HIGH : LAMP LOW HIGH LOW HIGH HIGH LOW LOW LOW LOW MODEL_OPT_1 MODEL_OPT_2 MODEL_OPT_3

2010Y,GP2
MODEL OPTION
MODEL_OPT_0 PIN NAME PIN NO. 8 11 30 31 HIGH B/L_LED PWM_BUZZ/IIC_LED TOUCH_KEY GPIO_LED LOW B/L_LAMP HIGH MODEL_OPT_1 MODEL_OPT_2 PWM_LED HIGH TACT_KEY LOW NON_GPIO_LED HIGH LOW LOW HIGH LE7300 GPIO LED & NO BUZZ HIGH LOW LOW HIGH HIGH LOW LOW HIGH LOW LOW MODEL_OPT_1 LOW MODEL_OPT_2 LOW MODEL_OPT_3 LOW LD350/450/550 PWM LED & No Buzz & No LED Blink 19/22/26LE5300/5300 IIC LED & PWM IIC BUZZ 32/37/42/47/55LE5300 IIC LED & PWM BUZZ LD420 IIC LED(09Y IIC Protocol) & No BUZZ MODEL_OPT_0

Description LK330/LK430 for KR/US 10Y EYE-Q Sensor KEY & PWM LED & No Buzz & No LED Blink LK330/LK430/LK530 KEY & PWM LED & No Buzz & No LED Blink LV25/LV35/LV45/LW45/LV55/LK45/LK55 S/T & IIC LED & NO BUZZ & LED Blink

PWM_BUZZ/IIC_LED : For model that use LED Lighting used IIC PWM_LED : For model that use LED Lighting used PWM Signal

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R MICOM Rev.4

20101125 5

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

CONTROL IR & LED

+3.5V_ST

R2404 10K 1%

R2405 10K 1%

EYEQ/TOUCH_KEY R2411 100 NEC_EEPROM_SCL C2408 18pF 50V OPT EYEQ/TOUCH_KEY 100 D2402 5.6V AMOTECH C2401 0.1uF C2402 0.1uF D2401 5.6V AMOTECH +3.5V_ST +3.5V_ST L2403 BLM18PG121SN1D NEC_EEPROM_SDA R2412 C2409 18pF 50V OPT

EYEQ/TOUCH_KEY

OLD_SUB P2401 12507WR-12L

NEW_SUB P2402 12507WR-15L

5.6V D2403 1 EYEQ/TOUCH_KEY 2 5.6V D2404 3 3 2 1

R2401 100 KEY1 R2402 100 KEY2

L2401 BLM18PG121SN1D

L2402 BLM18PG121SN1D

JP2407

JP2408

R2428 22 IR

R2425 47K OPT

+3.5V_ST

Q2406 2SC3052 OPT

C B E

R2430 10K OPT

R2429 47K OPT

+3.5V_ST

C2403 0.1uF 16V

C2404 1000pF 50V

R2413 LED_B/LG_LOGO

1.5K OPT C2410 0.1uF 16V

JP2409

C B Q2405 2SC3052 OPT E

R2431 47K OPT

R2426 47K

JP2410

+3.3V_Normal L2404 BLM18PG121SN1D

C2407 100pF 50V

D2405 5.6V

10

10

R2427 0 R2414 C2405 0.1uF 16V LED_R/BUZZ C2406 1000pF 50V 1.5K OPT R2416 10K

JP2411

11

11

12 13

12

13

14

15 16

S/T_SCL

NEW_SUB C906 18pF 50V OPT S/T_SDA NEW_SUB D903 CDS3C05HDMI1 5.6V D902 CDS3C05HDMI1 5.6V

C907 18pF 50V OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R IR/CONTROL-L

20101023 6

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

USB_DIODES
EAN61849601 L1451-*1 CIS21J121 NC L1451 MLB-201209-0120P-N2 120-ohm R1458 2K 1/8W 1% R1459 2K 1/8W 1% OUT_1 C1451 22uF 16V FLG 5 4 EN 6 3 IN_2 C1452 10uF 10V C1453 0.1uF +3.3V_Normal

IC1450 AP2191DSG
GND

8 $0.077 7

+5V_USB

OUT_2

IN_1

SIGN6409

R1455 4.7K OPT

3AU04S-305-ZC-(LG)

USB_JACK

USB1_CTL R1454 10K R1451 47

USB_JACK_LV3400 JK1450-*1

JK1450

USB1_OCD

3AU04S-345-ZC-H-LG

1 USB DOWN STREAM

USB DOWN STREAM

SIDE_USB_DM

SIDE_USB_DP

D1451 RCLAMP0502BA OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R USB_OCP_DIODE

20101023 7

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

HDMI EEPROM
5V_HDMI_1 +5V_Normal

A2

A1 ENKMC2838-T112 D821 C

HDMI_1_RENESAS

HDMI_1
SHIELD

5V_HDMI_1

5V_DET_HDMI_1

IC801-*1 R1EX24002ASAS0A
C A0 B R830 HPD1 10K E A1 2 7 WP A1 VCC A0

HDMI_1_ATMEL IC801 AT24C02BN-SH-T R874 10K

EDID_WP

R896 20 1K 19 18 17 16 R804 3.3K 1.8K R802 C802 0.1uF 16V

Q802 2SC3052

VCC

$0.055
2 7 WP C806 0.1uF R884 2.7K R888 2.7K

A2

SCL

A2

SCL R876 22 DDC_SCL_1

VSS DDC_SDA_1 DDC_SCL_1

SDA

GND

SDA R875 22 DDC_SDA_1

15 14 EAG59023302 13 A2 12 11 10 9 8 7 6 5 4 3 2 1 CK+ D0D0_GND D0+ D1D1_GND D1+ D2D2_GND VSS D2+ OPT D802 D2+_HDMI1 4 5 SDA GND 4 5 SDA DDC_SDA_2 R877 22 D1+_HDMI1 A2 D2-_HDMI1 3 6 SCL A2 3 6 SCL JP810 DDC_SCL_2 R878 22 D0+_HDMI1 D1-_HDMI1 A1 2 7 WP A1 A1 ENKMC2838-T112 D822 CK+_HDMI1 D0-_HDMI1 HDMI_2_RENESAS C HDMI_2_ATMEL IC802 AT24C02BN-SH-T R873 10K EDID_WP VCC A0 1 8 VCC C807 0.1uF R889 2.7K A2 C A1 ENKMC2838-T112 D824 HDMI_SIDE_ATMEL IC804 AT24C02BN-SH-T R871 10K CK-_HDMI1 R824 0 5V_HDMI_2 +5V_Normal

HDMI_CEC

HDMI_1

IC802-*1 R1EX24002ASAS0A
A0

$0.055
2 7

WP

R885 2.7K

JK802

HDMI_2
SHIELD

SIDE_HDMI
5V_HDMI_2 5V_DET_HDMI_2 5V_HDMI_4 5V_DET_HDMI_4 C BODY_SHIELD HPD2 20 E C801 0.1uF 16V R801 3.3K 19 18 17 DDC_SDA_2 16 DDC_SCL_2 DDC_SCL_4 15 R815 0 14 HDMI_CEC EAG62611201 13 12 11 10 9 8 D0+_HDMI2 D1-_HDMI2 7 6 5 D1+_HDMI2 D2-_HDMI2 4 3 2 D2+_HDMI2 OPT D801 1 CK+ CK+_HDMI4 D0D0-_HDMI4 D0_GND D0+ D0+_HDMI4 D1D1-_HDMI4 D1_GND D1+ D1+_HDMI4 D2D2-_HDMI4 D2_GND D2+ D2+_HDMI4 S B D 68K CK-_HDMI2 HDMI_SIDE JP806 R841 0 HDMI_CEC CK-_HDMI4 VSS 4 5 SDA GND 4 5 SDA A2 3 6 SCL A2 3 6 SCL JP812 R897 1K R837 R835 3.3K 1.8K C803 0.1uF 16V JP805 DDC_SDA_4 A1 Q803 2SC3052 E B R862 HPD4 10K HDMI_SIDE_RENESAS C R895 Q801 2SC3052 B

5V_HDMI_4 +5V_Normal

R828 10K

20 1K 19 18 17 16 15 14 EAG59023302 13 12 11 10 9 8 7 6 5 4 3 2 1 CK+ D0D0_GND D0+ D1D1_GND D1+ D2D2_GND D2+ R803 1.8K

IC804-*1 R1EX24002ASAS0A
A0 VCC A0

EDID_WP VCC

WP

$0.055
A1 2 7 WP C809 0.1uF R887 2.7K R891 2.7K DDC_SCL_4 R881 22 DDC_SDA_4 R882 22

HDMI_2

CK+_HDMI2 D0-_HDMI2

+3.3V_Normal

For CEC
D804

R854 R855 0 OPT

R856 10K

R857 68K OPT

CEC_REMOTE_S7

OPT D811

JK801

OPT C805 0.1uF 16V GND CEC_ON/OFF 68K R892 D825 R883 0 OPT

GND

JK803

D803 AVRL161A1R1NT

Q806 BSS83

+3.5V_ST

R893 10K

R853 68K

HDMI_CEC S B D CEC_REMOTE_NEC

D826 AVRL161A1R1NT

Q805 BSS83

OPT

C810 0.1uF 16V GND

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GND

GP2R HDMI

20101023 8

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

RGB/SPDIF/PC/HP
New Item Development
EARPHONE BLOCK
HP_LOUT C1118 10uF 16V 002:V7 C1115 1000pF 50V OPT HEAD_PHONE R1125 1K Q1101 MMBT3904-(F) E C B B E MMBT3904-(F) Q1104 C +3.3V_Normal R1130 10K GND L DETECT R 002:V7 C1119 10uF 16V JK3301 KJA-PH-0-0177 5 4 3 1 C

R1155 1K HP_ROUT HP_DET

Q1105 ISA1530AC1

+3.5V_ST

C1116 1000pF 50V OPT

R1128 1K

Q1102 MMBT3904-(F) E

B B

E MMBT3904-(F) Q1103 C

C R1129 3.3K E B Q1106 2SC3052 SIDE_HP_MUTE

PC AUDIO
JK1102 PEJ027-01 3 6A 7A 4 5 7B 6B E_SPRING T_TERMINAL1

RGB PC SPDIF OPTIC JACK


5.15 Mstar Circuit Application +3.3V_Normal

+5V_Normal D1115 ENKMC2838-T112 A1 C A2

JST1223-001 JK1103

B_TERMINAL1 PC_R_IN R_SPRING T_SPRING B_TERMINAL2 T_TERMINAL2 D1102 AMOTECH 5.6V OPT C1108 100pF 50V R1103 470K R1111 10K D1101 AMOTECH 5.6V OPT C1107 100pF 50V R1107 15K R1102 470K 002:S12 VCC R1110 10K SPDIF_OUT R1108 15K PC_L_IN 002:S12 002:T18 C1131 0.1uF 16V C1121 100pF 50V

GND

Fiber Optic

RGB_EEMPROM_RENESAS

RGB_EEMPROM_ATMEL IC1105 AT24C02BN-SH-T

IC1105-*1 R1EX24002ASAS0A
A0 A0 1 8 VCC A1 A1 2 7 WP A2 A2

R1139 2.2K
VCC

R1140 2.2K

R1142 10K

C1129 0.1uF 16V

VINPUT

WP

EDID_WP
SCL

FIX_POLE

SCL GND 4 5 SDA

RGB_DDC_SCL RGB_DDC_SDA C1127 18pF 50V C1128 18pF 50V R1141 22 R1143 22

VSS

SDA

DSUB_VSYNC

DSUB_HSYNC C1122 68pF 50V OPT D1109 30V

C1126 68pF 50V OPT

D1113 30V

D1114 5.6V OPT

D1116 5.6V OPT

DSUB_B+ R1133 75 D1110 30V

DSUB_G+ R1135 75 D1111 30V +3.3V_Normal

R1146 10K DSUB_DET DSUB_R+ R1137 75 D1112 30V D1117 5.6V OPT R1147 1K

GREEN_GND

DDC_CLOCK

DDC_DATA

BLUE_GND

SYNC_GND

RED_GND

SPG09-DB-010

DDC_GND

H_SYNC

V_SYNC

GND_2

GREEN

GND_1

BLUE

RED

NC

JK1104

10

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R RGB/SPDIF/HP

16

SHILED

11

12

13

14

15

20101023 9

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

RS232C
10 5 9 4 R1123 100 8
JP1121

3 R1124 100 7
JP1122

+3.5V_ST

2 D1107 CDS3C30GTH 30V OPT C1101 0.33uF IC1101 MAX3232CDR C1106 0.1uF D1108 CDS3C30GTH 30V OPT 6 1

SPG09-DB-009 JK1101

C1+ C1102 0.1uF C1103 0.1uF

16

VCC

V+

15

GND

C1-

14

DOUT1

C2+ C1104 0.1uF

13

RIN1

C2-

12

ROUT1 S7_NEC_RXD DIN1

VC1105 0.1uF

11

DOUT2

10

DIN2 S7_NEC_TXD

RIN2

8 EAN41348201

ROUT2

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R RS232C_9PIN

20101023 10

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

[51Pin LVDS Connector] (For FHD 60/120Hz)


PANEL_VCC

L702 120-ohm WAFER_FHD P703 FI-RE51S-HF-J-R1500 WAFER_FHD C700 10uF 16V OPT C709 1000pF 50V OPT C710 0.1uF 16V WAFER_FHD

[41Pin LVDS Connector] (For FHD 120Hz)


P704 FI-RE41S-HF-J-R1500 WAFER_FHD_120HZ

[30Pin LVDS Connector] (For HD 60Hz_Normal)


P705 FF10001-30 HD

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

1 2 3 4 5 6 7 8 9 10 RXDCKRXD4-

1 OPT 2 3 4 RXD4+ 5 RXD36 RXD3+ 7 8 9 RXDCK+ 10 11 RXD212 RXD2+ 13 RXD114 RXD1+ 15 RXD016 RXD0+ 17 18 19 RXC420 RXC4+ 21 RXC322 RXC3+ 23 PANEL_VCC 24 RXCCK25 RXCCK+ 26 27 RXC228 RXC2+ 29 RXC130 RXC1+ RXC0RXC0+ 31 C701 10uF 16V OPT OPT C702 1000pF 50V HD C703 0.1uF 16V L701 120-ohm HD R711 10K OPT RXA0RXA0+ R712 3.3K OPT RXA1RXA1+ LVDS_SEL +3.3V_Normal RXA2RXA2+ RXACKRXACK+ RXA3RXA3+ 0 R713 TP721 TP722 PWM_DIM OPC_OUT

RXA4RXA4+ RXA3RXA3+

11 12 13 14 15

RXACKRXACK+

16 17 18

RXA2RXA2+ RXA1RXA1+ RXA0RXA0+ BIT_SEL

19 20 21 22 23 24 25 R709 10K BIT_SEL_LOW 26 27 28 29 30 31

RXB4RXB4+ RXB3RXB3+

RXBCKRXBCK+

32 33 34

RXB2RXB2+ RXB1RXB1+ RXB0RXB0+ LVDS_SEL SCAN_BLK2 +3.3V_Normal 42 SCAN_BLK1/OPC_OUT R703 0 LVDS_PWM_44 R705 PWM_DIM 3.3K OPT R710 10K OPT R701 0 3D_SG R702 0 3D_SG LED_DRIVER_D/L_SDA

35 36 37 38 39 40 41

LED_DRIVER_D/L_SCL 100 2D/3D_CTL LVDS_51PIN_GPIO R706 R707 0 LVDS_51PIN_GND

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R LVDS_LARGE

20101023 11

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

VCC_1.5V_DDR

VCC_1.5V_DDR

VCC_1.5V_DDR VCC_1.5V_DDR

VCC_1.5V_DDR

R1201

R1204

1K 1%

1K 1%

R1224

0.1uF

1000pF

A-MVREFDQ 0.1uF 1000pF 1% R1205

1000pF

1000pF

0.1uF

0.1uF

A-MVREFCA C1205 0.1uF C1216 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C1217 C1221 C1206 C1207 C1208 C1210 C1211 C1212 C1214 C1215 C1218 C1219 C1220 C1222 C1223 C1224 C1235 0.1uF C1213 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C1234 0.1uF C1227 C1228 C1229 C1230 C1231 C1232 C1233 C1236 C1237 C1238 C1239 C1241 C1242 C1243 C1244 0.1uF C1245 C1246 10uF 10uF

1K 1%

1%

B-MVREFCA

B-MVREFDQ 1% R1225

R1202

1% C1250 1K

1K 1%

DDR3 1.5V By CAP - Place these Caps near Memory

C1201

C1202

C1204

C1203

C1247

C1248

Close to DDR Power Pin CLose to DDR3 CLose to Saturn7M IC

Close to DDR Power Pin CLose to Saturn7M IC CLose to DDR3

IC1201-*1 K4B1G1646G-BCH9
DDR_1333_SS_NEW N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3 M7 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 NC_5 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 BA0 BA1 BA2 A1 VDDQ_1 CK CK CKE L2 CS ODT RAS CAS WE VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 NC_1 RESET NC_2 NC_3 F3 NC_4 DQSL DQSL NC_6 J9 L1 L9 T7 F3 G3 A9 DQSU DQSU E7 D3 E3 F7 F2 F8 H3 H8 G2 H7 D7 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 D7 C3 C8 C2 A7 A2 B8 A3 DML DMU VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 E3 F7 F2 F8 H3 H8 G2 H7 E7 D3 C7 B7 T2 A8 C1 C9 D2 E9 F1 H2 H9 L2 K1 J3 K3 L3 J7 K7 K9 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 M2 N8 M3 M7 ZQ L8 VREFDQ H1 VREFCA M8 N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

C1249

1K

1K

1K

R1228

R1227

DDR3 1.5V By CAP - Place these Caps near Memory

VCC_1.5V_DDR

IC1202-*1 K4B1G1646G-BCH9
DDR_1333_SS_NEW M8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 NC_5 BA0 BA1 BA2 VDDQ_1 CK CK CKE CS ODT RAS CAS WE NC_1 RESET NC_2 NC_3 NC_4 DQSL DQSL A9 DQSU DQSU DML DMU DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 NC_6 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 J9 L1 L9 T7 A1 A8 C1 C9 D2 E9 F1 H2 H9 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 ZQ L8 VREFDQ H1 VREFCA

VCC_1.5V_DDR +1.5V_DDR

L1201 B-TMA0 R1213 A-MA0 1% 56 R1214 1% 56 AR1208 A-TMA0 C1225 10uF 10V C1226 0.1uF 16V

R1215 56 R1216 B-TMA2 56 AR1211 1% 1% B-MA0

M2 N8 M3

B-MA2 EAN61828901 B-MA11 B-MA1 B-MA8 B-MA6 DDR_1333_HYNIX B-MA0 B-MA1 B-MBA0 B-MA3 B-MA5 B-MA7 B-MA2 B-MA3 B-MA4 B-MA5 B-MA6 B-MA4 B-MA12 B-MBA1 B-MA10 B-MA7 B-MA8 B-MA9 B-MA10 B-MA11 B-MA12 B-MA13 B-MRESETB B-MBA2 B-MA13 B-MA9 M7 NC_5 B-MBA0 56 R1237 B-MBA1 B-MBA2 1% M2 N8 M3 J7 56 R1238 1% K7 B-MCKE K9 L2 B-MODT B-MRASB B-MCASB R1232 10K B-MDQSL B-MWEB B-MRESETB B-MDQSLB K1 J3 K3 L3 T2 RESET CS ODT RAS CAS WE NC_1 NC_2 NC_3 B-MDQSL B-MDQSLB B-MDQSU B-MDQSUB B-MDQL1 B-MDQL3 B-MDML B-MDQU2 B-MDML B-MDMU B-MDQL0 B-MDQL1 B-MCKE B-MDQL7 B-MDQL5 B-MDQL2 B-MDQL3 B-MDQL4 B-MDQL5 B-MDQL6 B-MDQL7 B-MDQL0 B-MDQL2 B-MDQL6 B-MDQL4 B-MDQU0 B-MDQU1 B-MDQU2 B-MDQU3 B-MDQU4 B-MDQU7 B-MDQU3 B-MDQU5 B-MDMU B-MDQU5 B-MDQU6 B-MDQU7 F3 G3 C7 B7 E7 D3 E3 F7 F2 F8 H3 H8 G2 H7 D7 C3 C8 C2 A7 A2 B8 A3 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9
F3 G3 C7 B7 DQSU DQSU DQSL DQSL T2 RESET L2 K1 J3 K3 L3 CS ODT RAS CAS WE J7 K7 K9

A-MA2 EAN61828901

A-TMA2

B-TMA11 B-TMA1 B-TMA8

IC1202 H5TQ1G63DFR-H9C
N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 BA0 BA1 BA2 VDDQ_1 CK CK CKE VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 J9 L1 L9 T7 A1 A8 C1 C9 D2 E9 F1 H2 H9 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 VCC_1.5V_DDR ZQ 240 1% L8 R1226 VREFDQ H1 VREFCA M8

IC1201 H5TQ1G63DFR-H9C
DDR_1333_HYNIX A-MVREFCA M8 VREFCA A0 A1 A-MVREFDQ R1203 240 1% B2 D9 G7 K2 K8 N1 N9 R1 VCC_1.5V_DDR R9 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 BA0 BA1 A1 A8 C1 C9 D2 E9 F1 H2 H9 J1 J9 L1 L9 T7 NC_1 NC_2 NC_3 NC_4 NC_6 DQSL DQSL A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 B1 B9 D1 D8 E2 E8 F9 G1 G9 VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 DQL7 D7 C3 C8 C2 A7 A2 B8 A3 DML DMU E3 F7 F2 F8 H3 H8 G2 H7 DQSU DQSU E7 D3 C7 B7 F3 G3 A-MDQSL A-MDQSLB A-MDQSU A-MDQSUB A-MDML A-MDMU A-MDQL0 A-MDQL1 A-MDQL2 A-MDQL3 A-MDQL4 A-MDQL5 A-MDQL6 A-MDQL7 A-MDQU0 A-MDQU1 A-MDQU2 A-MDQU3 A-MDQU4 A-MDQU5 A-MDQU6 A-MDQU7 RESET VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 CS ODT RAS CAS WE T2 CK CK CKE L2 K1 J3 K3 L3 A-MODT A-MRASB A-MCASB A-MWEB R1231 10K VCC_1.5V_DDR BA2 J7 K7 K9 A-MCKE NC_5 M2 N8 M3 A-MBA0 R1235 56 1% A-MBA1 A-MBA2 H1 VREFDQ A2 A3 A4 L8 ZQ A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 M7 N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3 A-MA0 A-MA1 A-MA2 A-MA3 A-MA4 A-MA5 A-MA6 A-MA7 A-MA8 A-MA9 A-MA10 A-MA11 A-MA12 A-MA13

K1 J3 K3 L3 T2

A-MA11 A-MA1 A-MA8 A-MA6 56 AR1203 A-MBA0 A-MA3 A-MA5 A-MA7 56 AR1204 A-MA4 A-MA12 A-MBA1 A-MA10 56 AR1201 A-MRESETB A-MBA2 A-MA13 A-MCK A-MA9 56 R1206 C1209 0.01uF 25V 1% A-MCK 22 R1207 A-MCKB 22 AR1202 A-MCKB A-MRASB A-MCASB A-MODT A-MWEB 56 R1208 A-MDQSL A-MRESETB A-MDQSLB 22 R1211 A-MDQSU 22 R1212 A-MDQSUB 22 AR1209 A-MDQL1 A-MDQL3 A-MDML A-MDQU2 22 AR1210 A-MCKE A-MDQL7 A-MDQL5 22 AR1205 A-MDQL0 A-MDQL2 A-MDQL6 A-MDQL4 22 AR1206 A-MDQU7 A-MDQU3 A-MDQU5 A-MDMU 22 AR1207 A-MDQU6 A-MDQU0 A-MDQU4 22 R1210 A-MDQU1 22 A-MCKE R1233 10K 22 R1209

A-TMA11 A-TMA1 A-TMA8 A-TMA6

B-TMA6 56 AR1214 B-TMBA0

B-MVREFCA

A-TMBA0 A-TMA3 A-TMA5 A-TMA7 A-TMA0 A-TMA1 A-TMA4 A-TMA12 A-TMBA1 A-TMA10 A-TMA2 A-TMA3 A-TMA4 A-TMA5 A-TMA6 A-TMA7 A-TMRESETB A-TMBA2 A-TMA13 A-TMA9 A-TMA8 A-TMA9 A-TMA10 A-TMA11 A-TMA12 A-TMA13 A-TMCK B8 B9 A8 C21 B10 A22 A10 B22 C9 C23 B11 A9 C10 B23

S7M-PLUS_DivX_MS10 IC101 LGE107DC-RP [S7M+ DIVX/MS10]


A25 A_DDR3_A0/DDR2_A13 A_DDR3_A1/DDR2_A8 A_DDR3_A2/DDR2_A9 A_DDR3_A3/DDR2_A1 A_DDR3_A4/DDR2_A2 A_DDR3_A5/DDR2_A10 A_DDR3_A6/DDR2_A4 A_DDR3_A7/DDR2_A3 A_DDR3_A8/DDR2_A6 A_DDR3_A9/DDR2_A12 A_DDR3_A10/DDR2_RASZ A_DDR3_A11/DDR2_A11 A_DDR3_A12/DDR2_A0 A_DDR3_A13/DDR2_A7 B_DDR3_A0/DDR2_A13 B_DDR3_A1/DDR2_A8 B_DDR3_A2/DDR2_A9 B_DDR3_A3/DDR2_A1 B_DDR3_A4/DDR2_A2 B_DDR3_A5/DDR2_A10 B_DDR3_A6/DDR2_A4 B_DDR3_A7/DDR2_A3 B_DDR3_A8/DDR2_A6 B_DDR3_A9/DDR2_A12 B_DDR3_A10/DDR2_RASZ B_DDR3_A11/DDR2_A11 B_DDR3_A12/DDR2_A0 B_DDR3_A13/DDR2_A7 B24 A24 P25 C24 P26 B26 R24 B25 T26 D24 A26 C25 T25

B-TMA3 B-TMA5 B-TMA7 56 AR1215 B-TMA4 B-TMA0 B-TMA1 B-TMA2 B-TMA3 B-TMA4 B-TMA5 B-TMA6 B-TMA7 B-TMA8 B-TMA9 B-TMA10 B-TMA11 B-TMA12 B-TMA13 B-TMCKB 22 AR1220 B-TMRASB B-TMCK 22 R1223 B-TMRESETB B-TMBA2 B-TMA13 B-TMA9 56 R1222 B-TMA12 B-TMBA1 B-TMA10 56 AR1219

B-MVREFDQ

G3 C7 B7

B-MCK B-MCK

C1240 0.01uF 25V

C3 C8 C2 A7 A2 B8 A3

B-MCKB

R1236 56

A-TMCKB A-TMBA0 A-TMBA1 A-TMRASB A-TMCASB A-TMODT A-TMWEB A-TMCK A-TMCKB A-TMCKE A-TMDQSL A-TMDQSLB A-TMODT A-TMRASB A-TMCASB A-TMDQSU A-TMDQSUB A-TMWEB A-TMRESETB A-TMBA2

B21 A11 A23 A12 C11 B12 A_DDR3_MCLK/DDR2_MCLK A_DDR3_MCLKZ/DDR2_MCLKZ A_DDR3_CKE/DDR2_DQ5 B_DDR3_MCLK/DDR2_MCLK B_DDR3_MCLKZ/DDR2_MCLKZ B_DDR3_CKE/DDR2_DQ5 A_DDR3_BA0/DDR2_BA2 A_DDR3_BA1/DDR2_CASZ A_DDR3_BA2/DDR2_A5 B_DDR3_BA0/DDR2_BA2 B_DDR3_BA1/DDR2_CASZ B_DDR3_BA2/DDR2_A5

P24 C26 R26 D26 D25 E24

B-MCKB B-MRASB B-MCASB B-MODT B-MWEB VCC_1.5V_DDR

B-TMBA0 B-TMBA1 B-TMBA2 B-TMCK B-TMCKB B-TMCKE

B-TMCASB B-TMODT B-TMWEB 56 R1219 B-TMDQSL 22 R1220 B-TMDQSLB 22

IC1201-*2 NT5CB64M16DP-CF
DDR_1333_NANYA_NEW N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3 M7 NC_5 M2 N8 M3 J7 K7 K9 CK CK CKE BA0 BA1 BA2 A1 VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 NC_1 NC_2 NC_3 NC_4 NC_7 J9 L1 L9 T7 F3 G3 A9 VSS_1 VSS_2 VSS_3 DML DMU VSS_4 VSS_5 VSS_6 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 D7 C3 C8 C2 A7 A2 B8 A3 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 D7 C3 C8 C2 A7 A2 B8 A3 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 E3 F7 F2 F8 H3 H8 G2 H7 E7 D3 C7 B7 T2 A8 C1 C9 D2 E9 F1 H2 H9 L2 K1 J3 K3 L3 J7 K7 K9 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 NC_6 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 M2 N8 M3 M7 ZQ L8 VREFDQ H1 EAN61857201 VREFCA M8 N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

IC1202-*2 NT5CB64M16DP-CF
DDR_1333_NANYA_NEW M8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 NC_6 NC_5 BA0 BA1 BA2 VDDQ_1 CK CK CKE CS ODT RAS CAS WE NC_1 RESET NC_2 NC_3 NC_4 DQSL DQSL A9 DQSU DQSU DML DMU DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 NC_7 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 J9 L1 L9 T7 A1 A8 C1 C9 D2 E9 F1 H2 H9 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 ZQ L8 VREFDQ H1 EAN61857201 VREFCA

NC_4 DQSL DQSL NC_6

C20 A20 B20 A21 C22 A_DDR3_RESETB B_DDR3_RESETB A_DDR3_ODT/DDR2_ODT A_DDR3_RASZ/DDR2_WEZ A_DDR3_CASZ/DDR2_BA1 A_DDR3_WEZ/DDR2_BA0 B_DDR3_ODT/DDR2_ODT B_DDR3_RASZ/DDR2_WEZ B_DDR3_CASZ/DDR2_BA1 B_DDR3_WEZ/DDR2_BA0

N25 M26 N24 N26 R25

B-TMODT B-TMRASB B-TMCASB B-TMWEB B-TMRESETB

R1217 B-TMDQSU 22 R1218 B-TMDQSUB 22 AR1212 B-TMDQL1 B-TMDQL3 B-TMDML B-MDQSUB B-MDQSU

A9 DQSU DQSU DML DMU VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

A-TMDQL1 A-TMDQL3 A-TMDML A-TMDQU2

A-TMDQSL A-TMDQSLB A-TMDQSU A-TMDQSUB

C16 B16 A16 C15 A14 B18 C18 B13 A19 C13 C19 A13 B19 C12 A15 A17 B14 C17 B15 A18 C14 B17 A_DDR3_DQU0/DDR2_DQ15 A_DDR3_DQU1/DDR2_DQ9 A_DDR3_DQU2/DDR2_DQ8 A_DDR3_DQU3/DDR2_DQ11 A_DDR3_DQU4/DDR2_DQM1 A_DDR3_DQU5/DDR2_DQ12 A_DDR3_DQU6/DDR2_DQM0 A_DDR3_DQU7/DDR2_DQ14 B_DDR3_DQU0/DDR2_DQ15 B_DDR3_DQU1/DDR2_DQ9 B_DDR3_DQU2/DDR2_DQ8 B_DDR3_DQU3/DDR2_DQ11 B_DDR3_DQU4/DDR2_DQM1 B_DDR3_DQU5/DDR2_DQ12 B_DDR3_DQU6/DDR2_DQM0 B_DDR3_DQU7/DDR2_DQ14 A_DDR3_DQL0/DDR2_DQ3 A_DDR3_DQL1/DDR2_DQ7 A_DDR3_DQL2/DDR2_DQ1 A_DDR3_DQL3/DDR2_DQ10 A_DDR3_DQL4/DDR2_DQ4 A_DDR3_DQL5/DDR2_DQ0 A_DDR3_DQL6/DDR2_CKE A_DDR3_DQL7/DDR2_DQ2 B_DDR3_DQL0/DDR2_DQ3 B_DDR3_DQL1/DDR2_DQ7 B_DDR3_DQL2/DDR2_DQ1 B_DDR3_DQL3/DDR2_DQ10 B_DDR3_DQL4/DDR2_DQ4 B_DDR3_DQL5/DDR2_DQ0 B_DDR3_DQL6/DDR2_CKE B_DDR3_DQL7/DDR2_DQ2 A_DDR3_DML//DDR2_DQ13 A_DDR3_DMU/DDR2_DQ6 B_DDR3_DML/DDR2_DQ13 B_DDR3_DMU/DDR2_DQ6 A_DDR3_DQSU/DDR2_DQSB1 A_DDR3_DQSUB/DDR2_DQS1 B_DDR3_DQSU/DDR2_DQSB1 B_DDR3_DQSUB/DDR2_DQS1 A_DDR3_DQSL/DDR2_DQS0 A_DDR3_DQSLB/DDR2_DQSB0 B_DDR3_DQSL/DDR2_DQS0 B_DDR3_DQSLB/DDR2_DQSB0

J25 J24 H26 H25 F26 L24 L25 F24 L26 F25 M25 E26 M24 E25 G26 J26 G24 K25 H24 K26 G25 K24

B-TMDQSL B-TMDQSLB B-TMDQSU B-TMDQSUB B-TMDML B-TMDMU B-TMDQL0 B-TMDQL1 B-TMDQL2 B-TMDQL3 B-TMDQL4 B-TMDQL5 B-TMDQL6 B-TMDQL7 B-TMDQU0 B-TMDQU1 B-TMDQU2 B-TMDQU3 B-TMDQU4 B-TMDQU5 B-TMDQU6 B-TMDQU7

B-TMDQU2 22 AR1213 B-TMCKE B-TMDQL7 B-TMDQL5 22 AR1216 B-TMDQL0 B-TMDQL2 B-TMDQL6 B-TMDQL4 22 AR1217 B-TMDQU7 B-TMDQU3 B-TMDQU5 B-TMDMU 22 AR1218 B-TMDQU6 B-TMDQU0 B-TMDQU4 22

A-TMCKE A-TMDQL7 A-TMDQL5

A-TMDML A-TMDMU A-TMDQL0 A-TMDQL1 A-TMDQL2

A-TMDQL0 A-TMDQL2 A-TMDQL6 A-TMDQL4

A-TMDQL3 A-TMDQL4 A-TMDQL5 A-TMDQL6 A-TMDQL7

A-TMDQU7 A-TMDQU3 A-TMDQU5 A-TMDMU

A-TMDQU0 A-TMDQU1 A-TMDQU2 A-TMDQU3 A-TMDQU4 A-TMDQU5

B-MDQU6 B-MDQU0 B-MDQU4


DDR_DVB_T2_2G
IC1201-*3 K4B2G1646C
N3 M8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 M7 NC_5 M2 N8 M3 J7 K7 K9 L2 K1 J3 K3 L3 T2 RESET CS ODT RAS CAS WE NC_1 NC_2 NC_3 F3 G3 C7 B7 E7 D3 E3 F7 F2 F8 H3 H8 G2 H7 D7 C3 C8 C2 A7 A2 B8 A3 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 D7 C3 C8 C2 A7 A2 B8 A3 DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7 DML DMU DQSU DQSU VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 DQSL DQSL A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 E3 F7 F2 F8 H3 H8 G2 H7 DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7 VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9 B1 B9 D1 D8 E2 E8 F9 G1 G9 E7 D3 DML DMU C7 B7 DQSU DQSU VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 NC_4 NC_6 CK CK CKE BA0 BA1 BA2 VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 J9 L1 L9 T7 F3 G3 DQSL DQSL A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 T2 RESET A1 A8 C1 C9 D2 E9 F1 H2 H9 L2 K1 J3 K3 L3 CS ODT RAS CAS WE NC_1 NC_2 NC_3 NC_4 NC_6 J7 K7 K9 CK CK CKE VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 M2 N8 M3 BA0 BA1 BA2 VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9 J1 J9 L1 L9 T7 A1 A8 C1 C9 D2 E9 F1 H2 H9 M7 NC_5 ZQ L8 VREFDQ H1 VREFCA N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 B2 D9 G7 K2 K8 N1 N9 R1 R9 ZQ L8 VREFDQ H1 VREFCA

E7 D3

A-TMDQU6 A-TMDQU0 A-TMDQU4

A-TMDQU6 A-TMDQU7

DDR_DVB_T2_2G
IC1202-*3 K4B2G1646C
M8

E3 F7 F2 F8 H3 H8 G2 H7

R1221 B-TMDQU1 22 B-MDQU1

P7 P3 N2 P8 P2 R8 R2 T8

A-TMDQU1 10K R1234 B-MCKE

R3 L7 R7 N7 T3

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R DDR_256

20101023 12
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

+3.3V_Normal S_FLASH_MAIN_MACRONIX R1404 4.7K

+3.3V_Normal

+3.3V_Normal

IC1401 MX25L8006EM2I-12G
CS# VCC C1401 0.1uF SO/SIO1

R1403 10K

/SPI_CS

SPI_SDO WP# /FLASH_WP C R1401 OPT 0 E B Q1401 KRC103S OPT GND

HOLD#

SCLK SPI_SCK R1405 SI/SIO0 33 SPI_SDI

S_FLASH_MAIN_WINBOND

IC1401-*1 W25Q80BVSSIG
CS VCC

DO[IO1]

HOLD[IO3]

%WP[IO2]

CLK

GND

DI[IO0]

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R SFLASH_1MB

20101023 13
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

GP2R_LARGE_TUNER
+5V_TU
RF_SWITCH_CTL Pull-up cant be applied because of MODEL_OPT_2 L3701 BOOSTER_OPT BLM18PG121SN1D

BOOSTER : CHINA OPT

BOOSTER_OPT R3734

close to TUNER
OPT R3762 0 CONTROL_ATTEN E

0 Q3701 BOOSTER_OPT ISA1530AC1 R3737 2.2K B C C BOOSTER_OPT Q3702 2SC3052 E

BOOSTER_OPT R3743 10K

CN_2INPUT_H_LG3911

BOOSTER_OPT R3745 10K

TU3702 TDTJ-S001D
DVB_1INPUT_H_LGIT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 SHIELD ANT_PWR[OPT] BST_CNTL +B NC[RF_AGC] AS SCL SDA NC[IF_TP] SIF NC VIDEO GND 1.2V 3.3V RESET IF_AGC_CNTL DIF_1 DIF_2

TU3701 TDFR-C036D
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

C3709 0.01uF 25V BOOSTER_OPT

BOOSTER_OPT

FE_BOOSTER_CTL LNA2_CTL The pull-up/down of LNA2_CTL is depended on MODLE_OPT_1. GPIO must be added for FE_BOOSTER_CTL

close to TUNER RF_S/W_CNTL


R3705 0

+5V_TU

+5V_TU

OPTION : RF AGC
C3703 100pF 50V C3704 0.1uF 16V C3728 0.1uF 16V OPT Q3704 2SC3052 OPT E C3731 10uF 10V OPT C B GPIO must be added. R3754 10K OPT TU_IIC_NON_ATSC_SANYO FE_AGC_SPEED_CTL IF_AGC_SEL TU_IIC_NON_ATSC_SANYO R3753 4.7K

BST_CNTL +B1[+5V] NC[RF_AGC] NC_1 SCLT SDAT NC_2 SIF NC_3 VIDEO

C3701 0.1uF 16V

RF_SW_OPT

R3755 470 E

R3758 82 TU_SIF

B C Q3705

+3.3V_TU
R3740-*1 1K TU_IIC_ATSC_SANYO R3740 1.2K R3741-*1 1K TU_IIC_ATSC_SANYO R3741 1.2K TU_SCL

ISA1530AC1

R3707

0 OPT

C3706 0.1uF 16V

33 R3735 TU_I2C_NON_FILTER

+5V_TU

TU_I2C_NON_FILTER C3713 33 R3736 18pF TU_I2C_NON_FILTER 50V TU_I2C_NON_FILTER C3742 C3711 20pF 18pF 50V 50V C3702 0.1uF 16V

C3743 20pF 50V TU_I2C_FILTER

TU_SDA

R3751 220

R3752 220

close to TUNER

TU_I2C_FILTER E R3749 0 R3750 1K OPT B C Q3703 ISA1530AC1

TU_CVBS

+3.3V_TU +3.3V_TU +1.2V/+1.8V_TU


FULL_NIM C3705 100uF 16V C3713-*1 C3711-*1 20pF 20pF 50V 50V TU_I2C_FILTER TU_I2C_FILTER TU_I2C_FILTER R3735-*1 TUNER_RESET close to the tuner pin, add,09029 C3710 0.1uF 16V COIL TU_I2C_FILTER R3736-*1 COIL

GND +B2[1.2V] +B3[3.3V] RESET NC_4


C3737 100pF 50V C3738 0.1uF 16V

CN C3739 10uF 6.3V

C3707 100pF 50V

C3708 0.1uF 16V R3732 100

R3733 100K

DEMOD_RESET

+3.3V_TU

This was being applied to the only china demod, so this has to be deleted in both main and ISDB sheet.

R3704

0 HALF_NIM

IF_AGC_MAIN
should be guarded by ground

R3742 4.7K FULL_NIM

R3744 4.7K FULL_NIM DEMOD_SCL HALF_NIM_1.2V_BCD IC3703

SCL SDA ERR SYNC


R3701

FULL_NIM R3702 100

100

FULL_NIM

close to IF line
C3712 22pF 50V FULL_NIM C3714 22pF 50V FULL_NIM

DEMOD_SDA

+3.3V_TU

AZ1117BH-ADJTRE1 INPUT ADJ/GND

R2 HALF_NIM R3767 10

+1.2V/+1.8V_TU

3 2

HALF_NIM R3760 0

IC3703-*1 AP1117EG-13

OUTPUT

VALID MCL D0 D1 D2 D3 D4 D5 D6
Close to the tuner R3761 0 HALF_NIM

IF_N_MSTAR
IN OUT ADJ/GND

HALF_NIM R3768 1.2K R1 HALF_NIM R3766 1 1/10W R3703 150 OPT

IF_P_MSTAR
1. should be guarded by ground 2. No via on both of them 3. Signal Width >= 12mils Signal to Signal Width = 12mils Ground Width >= 24mils

HALF_NIM_1.2V_DIODES Please, check multi Item! 10/12 C3740 0.1uF 16V HALF_NIM FULL_NIM_BCD R3748-*1 10K FULL_NIM_SEMTEK 7 ADJ

IC3701 AP2132MP-2.5TRG1 [EP]


R3771 C3717 0.1uF 16V 10K PG GND

C3741 10uF 10V HALF_NIM

+1.2V/+1.8V_TU
380mA

FULL_NIM_BCD R3770 10K EN 2

THERMAL

TUNER MULTI-OPTION

1 FULL_NIM_BCD 9

GP3_ATSC_1INPUT_H_SANYO

26 27 28 29 31 30

TU3702-*3 UDA55AL TU3702-*1 TDVJ-H101F


ANT_PWR[OPT] 1 BST_CNTL 2 +B 3 NC[RF_AGC] 4 AS 5 SCL 6 SDA 7 NC(IF_TP) 8 SIF 9 NC 10 VIDEO 11 GND 12 1.2V 13 3.3V 14 RESET 15 IF_AGC_CNTL 16 DIF_1 17 DIF_2 18 19 SHIELD SHIELD NC_1 NC_2 +B[+5V] NC[RF_AGC] AS SCL SDA NC(IF_TP) SIF NC_3 VIDEO GND +1.2V +3.3V RESET IF_AGC_CNTL DIF_1 DIF_2

R3748 5.1K
R1

FULL_NIM_SEMTEK VIN R3769 10K 4 3

R3764 0 1/10W FULL_NIM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

VOUT

+5V_Normal

FULL_NIM_BCD

FULL_NIM

VCTRL

NC

D7
FULL_NIM_BCD L3704

R3747 9.1K
1005 R2

FULL_NIM C3729 0.1uF 16V

FULL_NIM C3730 10uF 10V

SHIELD

IC3701-*1 SC4215ISTRT
Vo=0.8*(1+R1/R2) NC_1 GND

FULL_NIM

R3724

1 8 FULL_NIM_SEMTEK 2 7

FE_TS_SYNC

FE_TS_DATA[0-7]

EN

ADJ

FULL_NIM

R3730

FE_TS_VAL_ERR

GP3_ATSC_1INPUT_H_LGIT

VIN

VO

FULL_NIM FULL_NIM_CHINA

R3731

FE_TS_CLK NC_2 4 5 NC_3 FE_TS_DATA[0]


CN_2INPUT_H_ALTO

R3725

NTSC_2INPUT_H_LGIT

GP2R_AU_1INPUT_H_LGIT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 18 SHIELD 19 RF_S/W_CTL BST_CTL +B1[5V] NC_1[RF_AGC] NC_2 SCLT SDAT NC_3 SIF NC_4 VIDEO GND +B2[1.2V] +B3[3.3V] RESET IF/AGC DIF_1[N] DIF_2[P] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ANT_PWR NC_1 +B1[5V] RF_AGC MOPLL_AS SCL SDA NC_2 SIF NC_3 VIDEO GND +B2[1.2V] +B3[3.3V] RESET IF_AGC DIF_1[N] DIF_2[P]

FULL_NIM

R3727

TU3702-*4 TDTJ-S101D

FE_TS_DATA[1]
FULL_NIM_BR

TU3701-*4 TDFR-C236D
1 2 RF_S/W_CNTL BST_CNTL +B1[+5V] NC[RF_AGC] NC_1 SCLT SDAT NC_2 SIF NC_3 VIDEO GND +B2[1.2V] +B3[3.3V] RESET NC_4 SCL SDA ERR SYNC VALID MCL D0 D1 D2 D3 D4 D5 D6 D7

FULL_NIM

R3728

FE_TS_DATA[2]
TU3701-*2 TDFR-B036F

3 4

FULL_NIM

R3729

FE_TS_DATA[3] FE_TS_DATA[4]

1 2

RF_S/W_CNTL BST_CNTL

5 6

FULL_NIM

+B1[5V] NC_1[RF_AGC] NC_2 SCLT SDAT

R3726

7 8 9 10

4 5 6

FULL_NIM

R3721

FE_TS_DATA[5]

8 9 10

NC_3 SIF NC_4 VIDEO GND

11 12 13 14

FULL_NIM

R3722

11

FE_TS_DATA[6]

12 13 14

+B2[1.2V] +B3[3.3V] RESET NC_5 SCL

15 16 17 18

FULL_NIM_CHINA

R3723

15

FE_TS_DATA[7]

16 17 18 19

SDA ERR SYNC VALID MCL

+5V_TUNER

19 20 21 22

+3.3V_Normal +5V_TU
200mA Size change L3702 MLB-201209-0120P-N2 C3719 22uF 10V C3724 0.1uF 16V C3722 22uF 16V C3726 0.1uF 16V 60mA

TU3702-*2 TDTR-T036F

Close to the CI Slot


SHIELD

20 21 22 23

+3.3V_TU

D0 D1 D2 D3 D4

23 24 25 26

R3706

24

25 26 27 28 29 31 30

Size change L3703 MLB-201209-0120P-N2 C3715 C3727 22uF 0.1uF 10V 16V

FULL_NIM_BR

D5 D6 D7

27 28 29

SHIELD

C3723 22uF 10V

C3725 0.1uF 16V

31

30

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SHIELD

location movement,0929

Add,0929

GP2R TUNER_L

20101023 14
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

+1.8V_AMP +3.3V_Normal IC404 AP1117E18G-13 IN 3 Vd=1.4V 1 2 C434 0.1uF 16V OUT C421 10uF 10V C446 0.1uF 16V +24V ADJ/GND R474 1

120 mA

SPK_L+ OPT R535 3.3 C521 10uF 35V OPT C547 0.01uF 50V D502 1N4148W 100V OPT D501 1N4148W 100V OPT R519 12 C529 390pF 50V C530 390pF 50V R520 12 R524 12 R526 12

L506 10.0uH NRS6045T100MMGK 10.0uH L507 NRS6045T100MMGK C534 0.47uF 50V

C536 0.1uF 50V

R527 4.7K

SPEAKER_L
C537 0.1uF 50V R528 4.7K SPK_L-

+3.3V_Normal BLM18PG121SN1D C514 22000pF 50V L504 PGND1A_2 PGND1A_1 PVDD1A_2 PVDD1A_1 PVDD1B_2 PVDD1B_1

C515 0.1uF 50V

C519 0.1uF 50V

C518 22000pF 50V PGND1B_2 PGND1B_1 C520 1uF 25V

OUT1A_2

OUT1A_1

OUT1B_2

EP_PAD

OUT1B_1

BST1B 44

C506 1000pF 50V AUD_MASTER_CLK +1.8V_AMP +1.8V_AMP BLM18PG121SN1D

TP502

AMP_RESET

56

55

54

53

52

51 50

49

48

47

46

45

43

VDR1B

C512 1uF C509 0.1uF

BST1A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 NTP-7100 EAN60969603 IC501 THERMAL 57

42 41 40 39 38 37 36 35 34 33 32 31 30 29

NC VDR2A BST2A

VDR1A 25V /RESET AD DGND_1 GND_IO CLK_I

C522 25V1uF

SPK_R+ C525 22000pF 50V

PGND2A_2 PGND2A_1 OUT2A_2 OUT2A_1 PVDD2A_2 PVDD2A_1 PVDD2B_2 PVDD2B_1 OUT2B_2 OUT2B_1 PGND2B_2

D503 1N4148W 100V OPT

R521 12 C531 390pF 50V C532 390pF 50V R522 12

R525 12

NRS6045T100MMGK L508 10.0uH C535 0.47uF 50V

C538 0.1uF 50V

R529 4.7K

BLM18PG121SN1D

L502 C504 100pF 50V C508 1000pF 50V R508 3.3K C433 10uF 10V OPT

VDD_IO DGND_PLL AGND_PLL LF AVDD_PLL DVDD_PLL GND

L509 10.0uH NRS6045T100MMGK R523 12

SPEAKER_R

L501

D504 1N4148W 100V OPT +24V

C539 0.1uF 50V

R530 4.7K SPK_R-

OPT C501 10uF 10V

C502 0.1uF 16V

OPT C503 10uF 10V

C505 0.1uF 16V +1.8V_AMP

SDATA

VDR2B

MONITOR0

MONITOR1

MONITOR2

BST2B

WCK

BCK

SDA

SCL

PGND2B_1

DGND_2

/FAULT

DVDD

C526 0.1uF 50V C524 22000pF 50V

C527 0.1uF 50V

C528 10uF 35V

OPT C511 10uF 10V

C513 0.1uF 16V

C517 1uF 25V

AUD_LRCH AUD_LRCK AUD_SCK AMP_SDA AMP_SCL

R503 R504 R505 R506 R507

100 100 100 33 33 C507 18pF 50V C510 18pF 50V C546 22pF 50V OPT C544 22pF 50V OPT C545 22pF 50V OPT R514 100 R515 10K C Q501 2SC3052 E B R517 AMP_MUTE 10K SPK_L3 SPK_L+ 4 C516 1000pF 50V OPT R513 0 POWER_DET

+3.5V_ST

WAFER-ANGLE

SPK_R+

SPK_R-

1 P501

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R AMP_NTP

20101023 16
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Rear AV
AV_CVBS_IN REAR_AV D1619 R1654 30V 75 REAR_AV C1643 47pF 50V REAR_AV C1648 220pF 50V +3.3V_Normal OPT

COMPONENT2

+3.3V_Normal

R1612 10K

R1615 1K COMP2_DET

JK1604 PPJ233-01 5C 4C 3C 4B 3A 4A 5A [RD]E-LUG [RD]O-SPRING [RD]CONTACT L-MONO [WH]C-LUG [YL]CONTACT [YL]O-SPRING [YL]E-LUG D1625 5.6V REAR_AV R1671 470K REAR_AV D1624 5.6V OPT

R1660 10K REAR_AV R1666 1K REAR_AV AV_CVBS_DET

D1613 5.6V OPT

ETHERNET FOR DVB_T2

C1646 0.1uF 16V REAR_AV

[GN]E-LUG 6A [GN]O-SPRING REAR_AV R1685 10K REAR_AV AV_R_IN C1663 330pF 50V REAR_AV R1689 12K 5A [GN]CONTACT 4A [BL]E-LUG-S 7B [BL]O-SPRING 5B [RD]E-LUG-S 7C [RD]O-SPRING_1 AV_L_IN 5C [WH]O-SPRING 5D [RD]CONTACT 4E [RD]O-SPRING_2 5E [RD]E-LUG 6E PPJ234-01 JK1603 REAR_COMP2 D1617 5.6V R1632 10K COMP2_R_IN R1626 470K C1617 1000pF 50V OPT R1634 12K TP1618 TP1619 TP1620 D1616 5.6V R1625 470K C1616 1000pF 50V OPT R1636 12K D1615 30V R1633 10K COMP2_L_IN TP1616 TP1617 R1621 75 COMP2_Pr+ TP1614 TP1615 D1614 30V R1620 75 COMP2_Pb+ TP1612 TP1613 TP1611 D1612 30V R1619 75 COMP2_Y+

L1609 120-ohm REAR_AV

TP1610

ET_RXD0 ET_TXD0 ET_RXD1 ET_TXD1 ET_REF_CLK ET_TX_EN ET_MDC ET_MDIO ET_CRS ET_RXER /RST-PHY

L1610 120-ohm REAR_AV REAR_AV D1626 5.6V R1672 470K REAR_AV REAR_AV

REAR_AV R1684 10K

C1662 330pF 50V REAR_AV

R1688 12K REAR_AV

IC1601-*1 SN324

OUT1

14 EU_OPT_AUK

OUT4

INV_IN1

13

INV_IN4

+3.3V_Normal

NON_INV_IN1

12

NON_INV_IN4

R1613 10K SC1/COMP1_DET R4223 0 D1611 5.6V OPT C1607 0.1uF 16V R1614 1K IN CASE OF SMALL= 15V EU_OPT L1606 SC1_SOG_IN EU_OPT E ISA1530AC1 Q1601 SC1_CVBS_IN EU_OPT R1609 75 D1602 30V OPT EU_OPT C1604 47pF 50V C1608 220pF 50V OPT C EU_OPT R4211 390 C B EU_OPT Q1602 2SC3052 B EU_OPT R1641 47K EU_OPT C1621 47uF 16V DTV/MNT_VOUT EU_OPT R1640 470 EU_OPT C1623 0.1uF 50V +12V/+15V

VCC

11

GND

NON_INV_IN2

10

NON_INV_IN3

INV_IN2

INV_IN3

COMPONENT1

EU_OPT R4210 0

EU_OPT C1625 0.1uF 50V

OUT2

OUT3

EU_OPT AV_DET FIX-TER 11 10 [GN]G 9 [GN]C_DET 8 [BL]B 7 [RD]R 6 [WH]L_IN 5 [RD]R_IN 4 [RD]MONO 13 PPJ-230-01 JK1601 COMPONENT1 10 G_GND 9 ID 8 B_OUT 7 AUDIO_L_IN 6 B_GND 5 AUDIO_GND 4 AUDIO_L_OUT 3 AUDIO_R_IN 2 AUDIO_R_OUT 1 D1607 5.6V NON_EU R1606 470K D1606 30V R1605 75 13 D2B_OUT 12 G_OUT 11 D2B_IN 17 RGB_IO 16 R_OUT 15 RGB_GND 14 R_GND R4221 0 EU_OPT D1604 30V [GN]GND 21 SYNC_IN 20 SYNC_OUT 19 SYNC_GND2 18 SYNC_GND1 D1603 30V OPT D1610 30V OPT 22 COM_GND

EU_OPT_BCD

IC1601 AS324MTR-E1 CLOSE TO MSTAR


DTV/MNT_L_OUT EU_OPT C1644 10uF 16V R4218 22K EU_OPT R1656 2.2K EU_OPT R1664 33K OUT1 1 14 OUT4

EU_OPT R1635 390 EU_OPT R1628 75 EU_OPT C1620 100uF 16V Rf

Rg

Gain=1+Rf/Rg

EU_OPT R1639 180

EU_OPT R1642 15K +12V/+15V

C1664 0.01uF R4219 100

OPT R1662 470K EU_OPT R1657 5.6K

IN1EU_OPT R1667 10K IN1+

13

IN4-

SC1_R+/COMP1_Pr+ R1608 75

EU_OPT R1616 75

EU_OPT R1627 22

SC1_FB

EU_OPT C1654 33pF

12

IN4+

SCART1_Lout

VCC C1642 0.1uF SCART1_Rout 50V EU_OPT R1658 5.6K EU_OPT R1665 33K

11

GND

R4216

100 C1665 0.01uF

IN2+

10

IN3+

SC1_G+/COMP1_Y+ D1605 30V R1604 75

OPT 30V REC_8 D1716

EU_OPT

R4217 22K EU_OPT R1655 2.2K DTV/MNT_R_OUT OPT R1661 470K

IN2R1668 10K OUT2

IN3-

C1655 33pF EU_OPT EU_OPT

OUT3

SC1_B+/COMP1_Pb+

OPT EU_OPT D1618 R1623 30V 15K

SC1_ID EU_OPT R1629 3.9K

C1645 10uF 16V EU_OPT

R1617 10K SC1/COMP1_L_IN L1604 120-ohm C1611 330pF 50V R1630 12K

[SCART PIN 8]

+12V/+15V IN CASE OF SMALL= 15V

PSC008-01 JK1602
D1609 5.6V NON_EU L1603 120-ohm R1607 470K C1612 330pF 50V

R1618 10K SC1/COMP1_R_IN R1631 12K OPT R1675 2K

OPT R1687 10K OPT R1677 10K OPT R1680 1K OPT R1676 560 C SC_RE2 SCART1_MUTE DTV/MNT_R_OUT EU_OPT Q1608 2SC3052 3 2 EU_OPT R1650 2K 1 EU_OPT C1636 0.1uF OPT R1678 680 OPT R1681 1K B OPT Q1611 2SC3052 E B OPT R1695 12K C B OPT Q1613 E 2SC3052

C OPT Q1615 2SC3052 E

Full Scart/ Comp1


DTV/MNT_L_OUT D1608 5.6V OPT EU_OPT L1601 BLM18PG121SN1D EU_OPT C1609 1000pF 50V EU_OPT C1618 4700pF

[SCART AUDIO MUTE]


+3.5V_ST SC_RE1 DTV/MNT_L_OUT EU_OPT Q1607 2SC3052

R4207 51K OPT

REC_8

EU_OPT R1648 2K

EU_OPT RT1P141C-T112 Q1610

EU_OPT R1652 10K

DTV/MNT_R_OUT D1601 5.6V OPT EU_OPT L1602 BLM18PG121SN1D EU_OPT C1610 1000pF 50V EU_OPT C1619 4700pF

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R REAR_JACK

20101023 17
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

SIDE CVBS PHONE JACK (New Item Development)


JK9901 KJA-PH-1-0177 5 5A 4A 3A 4B 3C 4C 5C PPJ235-01 JK9903 SIDE_AV_3HOLE SIDE_CVBS D9904 5.6V ADMC5M03200L_AMODIODE SIDE_CVBS R9905 470K [YL]E-LUG 4 [YL]O-SPRING 3 [YL]CONTACT 1 [WH]O-SPRING 6 [RD]CONTACT SIDE_AV_GENDER [RD]O-SPRING [RD]E-LUG SIDE_CVBS D9903 5.6V ADMC5M03200L_AMODIODE SIDE_CVBS R9906 470K M6 M1 OPT D9902 5.6V ADMC5M03200L_AMODIODE M3_DETECT C9901 100pF SIDE_CVBS M4 M5_GND SIDE_CVBS D9901 30V ADUC30S03010L_AMODIODE SIDE_CVBS R9907 75 SIDE_CVBS L9903 BLM18PG121SN1D SIDEAV_CVBS_IN

+3.3V_Normal
SIDE_CVBS 10K R9911 SIDE_CVBS R9915 1K

C9907 100pF OPT

SIDEAV_DET

SIDE_CVBS L9902 BLM18PG121SN1D

SIDE_CVBS R9914 SIDEAV_L_IN SIDE_CVBS 10K C9906 100pF 50V SIDE_CVBS R9913 SIDE_CVBS C9905 100pF 50V 10K SIDE_CVBS R9917 12K

SIDE_CVBS L9901 BLM18PG121SN1D

SIDEAV_R_IN SIDE_CVBS R9916 12K

SIDE COMPONENT PHONE JACK (New Item Developmen)


+3.3V_Normal R9904 10K SIDE_COMP D9908 5.6V OPT JK9902 KJA-PH-1-0177 5 4 3 1 6 M5_GND M4 M3_DETECT M1 M6 SIDE_COMP SIDE_COMP 75 R9908 D9906 30V SIDE_COMP COMP2_Pr+ SIDE_COMP D9907 30V SIDE_COMP D9905 30V 75 R9909 SIDE_COMP COMP2_Pb+ SIDE_COMP R9910 75 COMP2_Y+ R9912 1K COMP2_DET SIDE_COMP

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R SIDE_JACK

20101023 18
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

* Option name of this page : CI_SLOT (because of Hong Kong) CI Region


CI SLOT
+5V_CI_ON CI_DATA[0-7]

CI TS INPUT

CI_DATA[0-7]

+5V_Normal C1906 10uF 10V 10K EAG41860102 CI_SLOT_JACK_LV3400 P1901 P1902 10067972-050LF 10067972-000LF 35 R1908 AR1901 CI_TS_DATA[4] CI_TS_DATA[5] CI_TS_DATA[6] CI_TS_DATA[7] R1905 CI_IORD CI_IOWR CI_MDI[0] CI_MDI[1] CI_MDI[2] CI_MDI[3] C1905 GND CI_MDI[4] CI_MDI[5] CI_MDI[6] CI_MDI[7] R1906 PCM_RST /PCM_WAIT REG CI_TS_CLK CI_TS_VAL CI_TS_SYNC R1901 R1902 47 AR1902 33 47 10K 0.1uF R1910 OPT 0 10K 33 100 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 CI_TS_DATA[0] CI_TS_DATA[1] CI_TS_DATA[2] CI_TS_DATA[3] AR1903 /CI_CD2 +5V_Normal R1907 100 33 66 67 68 0 OPT G2 2 69 G1 1 CI_SLOT_JACK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 CI_DATA[0] CI_DATA[1] CI_DATA[2] R1916 OPT 0 C1909 0.1uF GND R1920 100 R1919 47 CI_DATA[3] CI_DATA[4] CI_DATA[5] CI_DATA[6] CI_DATA[7]

CI_MDI[7] CI_MDI[6] CI_MDI[5] CI_MDI[4] CI_MDI[3] CI_MDI[2] CI_MDI[1] CI_MDI[0]

33

AR1905

FE_TS_DATA[7] FE_TS_DATA[6] FE_TS_DATA[5] FE_TS_DATA[4] @netLa FE_TS_DATA[0-7]

R1903

33

AR1906

FE_TS_DATA[3] FE_TS_DATA[2] FE_TS_DATA[1] FE_TS_DATA[0]

/CI_CD1 C1903 0.1uF 16V

CI_DATA[0-7]

R1921 10K

AR1904 CI_MISTRT CI_ADDR[10] CI_ADDR[11] CI_ADDR[9] CI_ADDR[8] CI_ADDR[13] CI_ADDR[14] CI_WE /PCM_IRQA /PCM_CE CI_OE CI_MIVAL_ERR CI_MCLKI

33 FE_TS_SYNC FE_TS_VAL_ERR

FE_TS_CLK

CI_ADDR[12] CI_ADDR[7] CI_ADDR[6] CI_ADDR[5] CI_ADDR[4] CI_ADDR[3] CI_ADDR[2] CI_ADDR[1] CI_ADDR[0]

CI HOST I/F

CI_ADDR[0-14]

R1909

CI_DET GND 1OE

IC1902

GND 1A1 R1904 10K C1904 0.1uF 16V GND PCM_A[0] 2Y4 CI_ADDR[7] 1A2 CI_MISTRT CI_MIVAL_ERR CI_MCLKI 1A3 PCM_A[2] 2Y2 CI_ADDR[5] 1A4 PCM_A[3] 2Y1 CI_ADDR[4] GND PCM_A[1] 2Y3 CI_ADDR[6]

1 TOSHIBA 2 0ITO742440D 3

20

+3.3V_CI C1913 0.1uF VCC 16V

19

2OE

18

1Y1 CI_ADDR[0] 2A4 PCM_A[7] 1Y2 CI_ADDR[1] 2A3 PCM_A[6] 1Y3 CI_ADDR[2] 2A2 PCM_A[5] 1Y4 CI_ADDR[3] 2A1 PCM_A[4]

4 TC74LCX244FT

17

16

15

14

13

CI DETECT

12

10

11

+3.3V_Normal

+3.3V_CI
CI_SLOT_OR_GATE_NXP IC1901 74LVC1G32GW

+3.3V_CI

+3.3V_CI

C1908

0.1uF 16V

R1917

/CI_CD1

GND

OPT

10K

L1901 BLM18PG121SN1D

VCC

/CI_CD2

C1901 0.1uF
OPT

C1902 0.1uF

CI_DATA[0] GND R1915 CI_DATA[0-7] CI_DET 47 R1918 /PCM_CD 47 CI_DATA[1] CI_DATA[2] CI_DATA[3]

33

AR1907

PCM_D[0] PCM_D[1] PCM_D[2] PCM_D[3] PCM_D[0-7]

CI_DATA[4] CI_DATA[5] CI_DATA[6] CI_DATA[7]

33

AR1908

PCM_D[4] PCM_D[5] PCM_D[6] PCM_D[7]

CI POWER ENABLE CONTROL


PCM_D[0-7] CI_DATA[0-7]

+5V_CI_ON +5V_Normal S C1907 Q1902 RSR025P03 D C1910 0.1uF R1923 10K OPT L1902 BLM18PG121SN1D 33 AR1912 PCM_A[8] PCM_A[9] PCM_A[10] PCM_A[11]

CI_ADDR[8] CI_ADDR[9] CI_ADDR[10] C1912 0.1uF 16V OPT CI_ADDR[11]

0.1uF 16V R1912 10K OPT R1914 22K

G C1911 4.7uF 16V

16V

CI_ADDR[12] CI_ADDR[13] CI_ADDR[14] R1922 2.2K REG

33

AR1913 PCM_A[12] PCM_A[13] PCM_A[14] /PCM_REG

R1913 10K PCM_5V_CTL

C B R1924 10K Q1901 2SC3052 E CI_OE CI_WE CI_IORD CI_IOWR AR1909 33 /PCM_OE /PCM_WE /PCM_IORD /PCM_IOWR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R PCMCI

20101023 20
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
6.5T_GAS 8.5T_GAS MDS62110209 GAS1-*5 8.5T_GAS MDS62110209 GAS2-*5 8.5T_GAS MDS62110209 GAS3-*5 12.5T_GAS MDS61887708 GAS1-*4 12.5T_GAS MDS61887708 GAS2-*4 12.5T_GAS MDS61887708 GAS3-*4 8.5T_GAS MDS62110209 GAS4-*5 12.5T_GAS MDS61887708 GAS4-*4 9.5T_GAS MDS61887710 GAS1-*3 9.5T_GAS MDS61887710 GAS2-*3 9.5T_GAS MDS61887710 GAS3-*3 9.5T_GAS MDS61887710 GAS4-*3 7.5T_GAS MDS62110205 GAS1-*2 7.5T_GAS MDS62110205 GAS2-*2 7.5T_GAS MDS62110205 GAS3-*2 7.5T_GAS MDS62110205 GAS4-*2 5.5T_GAS MDS62110204 GAS1-*1 5.5T_GAS MDS62110204 GAS2-*1 MDS62110206 GAS1 6.5T_GAS MDS62110206 GAS2 5.5T_GAS MDS62110204 GAS3-*1 5.5T_GAS MDS62110204 GAS4-*1 6.5T_GAS MDS62110206 8.5T_GAS MDS62110209 GAS5-*5 12.5T_GAS MDS61887708 GAS5-*4 9.5T_GAS MDS61887710 GAS5-*3 7.5T_GAS MDS62110205 GAS5-*2 5.5T_GAS MDS62110204 GAS5-*1 6.5T_GAS MDS62110206 GAS5 8.5T_GAS MDS62110209 GAS6-*5 12.5T_GAS MDS61887708 GAS6-*4 9.5T_GAS MDS61887710 GAS6-*3 7.5T_GAS MDS62110205 GAS6-*2 5.5T_GAS MDS62110204 GAS6-*1 6.5T_GAS MDS62110206 GAS6 8.5T_GAS MDS62110209 GAS7-*5 12.5T_GAS MDS61887708 GAS7-*4 9.5T_GAS MDS61887710 GAS7-*3 7.5T_GAS MDS62110205 GAS7-*2 5.5T_GAS MDS62110204 GAS7-*1 6.5T_GAS MDS62110206 GAS7 GAS4 6.5T_GAS MDS62110206 GAS3

SMD GASKET

GP2R SMD_GAS 20101023 20


LGE Internal Use Only

L/DIM_LED/DRIVER P2100 12507WR-08L

+3.3V_Normal +3.3V_Normal

R2102 10K LED_DRIVER_D/L OPT 1 R2103 10K FRC_L/DIM_REVERSE_SEL LED_DRIVER_D/L

R2101 2.2K

R2100 2.2K

L/DIM_SCLK

LED_DRIVER_D/L R4029 22 LED_DRIVER_D/L_SCL R4028 22 LED_DRIVER_D/L_SDA LED_DRIVER_D/L

L/DIM_MOSI

8 9

V_SYNC C2100 18pF 50V OPT C2101 18pF 50V OPT C2102 18pF 50V OPT C2103 18pF 50V OPT C2104 18pF 50V OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP2R L/DIM_LED

20101023 21
LGE Internal Use Only

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

TI solution RF-3D OPTION


+3.3V_Normal P3401 12507WR-12L 3D_SG 1 3.3V L3401 120-ohm 3D_SG +3.3V_Normal

GND 3D_SG R3402 100 3D_SG R3408 100 M_REMOTE_TX RESET 3D_SG R3409 100 M_RFModule_RESET DC 3D_SG R3401 100 DD_MREMOTE 3D_SG R3407 100 DC_MREMOTE R3410 M_REMOTE_RX 2.7K 3D_SG R3411 2.7K 3D_SG R3412 2.7K 3D_SG

RX

TX

FREQ. GPOIO_0
3D Off 60Hz

GPOIO_1

GPOIO_2

0 0 0 0 1 1 1 1

0 0 1 1 0 0 1 1

0 1 0 1 0 1 0 1

DD

GND 3D_SG R3406 22 3D_SG R3404 22 3D_SG R3405 22 3D_GPIO_2 3D_SYNC 3D_SG R3403 22 3D_SYNC_RF 3D_GPIO_0

59.94Hz 50Hz RESERVED RESERVED RESERVED

GPIO_0

10

GPIO_1

3D_GPIO_1 GPIO_2

11

12 13 .

RESERVED

ALL 3D-SG OPTION

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright 2010 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

LCD TV Repair Guide `11 years New Basic Models

Contents
1. Product Roadmap 2. Main PCB layout 3. Block Diagram 4. Interconnection 5. Standard Repair Process

LCD TV EU Group LCD TV Research Department JAN. 28th, 2011

Overview for 11 Year Model

LCD TV Repair Guide


`11 years New Models

< Applicable Basic Model > xxLK330, xxLK430, xxLK450, xxLK530, xxLK550 xxLV2300, xxLV2500, xxLV2540, xxLV3400 xxLV3500, xxLV3550, xxLV5500, xxLV4500 xxLW4500 (3D)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

2/22

LGE Internal Use Only

Product Roadmap
2011 2011

Lamp Edge LED

3D

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

3/22

LGE Internal Use Only

Main PCB 19/22/26LV2500 (50HZ)


To LCD Module
1 Main processor, DDR Memory Flash Memory Micom for Key/IR sensing Audio AMP (5W+5W)

2 3

Adapter

* 19/22/26LV2500_S7 Reused (11) Main IC : LGE101_Mstar Tuner Type : TDTJ-S001D (DVB-T/C) Display Type (Resolution) : LED TV (1366 x 768) Interface : HDMI 2EA , Component 1EA, AV 1EA, USB 1EA Difference : Without FRC, HDMI Position , Resolution , Interface, Wafer Position (Sub)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

4/22

LGE Internal Use Only

Main PCB 22/26LK330 (50HZ)


To LCD Module
1 2 Main processor, DDR Memory Flash Memory Micom for Key/IR sensing Audio AMP (5W+5W)

1 2

Adapter

* 22/26LK330_S7 Reused (11) Main IC : LGE101_Mstar Tuner Type : TDTJ-S001D (DVB-T/C) Display Type (Resolution) : LCD TV (1366 x 768) Interface : HDMI 2EA , Component 1EA, AV 1EA, USB 1EA Difference : Without FRC, HDMI Position , Resolution , Interface, Wafer Position (Sub)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

5/22

LGE Internal Use Only

Main PCB 32/37/42/47LK450 (50HZ)


Power

To LCD Module
LVDS

1 2

Main processor, DDR Memory Flash Memory Micom for Key/IR sensing Audio AMP (10W+10W)

1 2

IR
3

* 32/37/42/47LK450_S7 Reused (11) Main IC : LGE101_Mstar Tuner Type : TDTJ-S001D (DVB-T/C) Display Type (Resolution) : LCD TV (1920 x 1080) Interface : HDMI 3EA , Component 1EA, AV 1EA, USB 1EA Difference : Without FRC, HDMI Position , Resolution , Interface, Wafer Position (Sub)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

6/22

LGE Internal Use Only

Main PCB 32/37/42/47/55LW4500 (100HZ)


LVDS
Led Driver Power 4 1
1 2 3 Main processor, DDR Memory Flash Memory Micom for Key/IR sensing Audio AMP (10W+10W) LED Driver connection (with local dimming)

4 2

IR
3

* 37LW4500_S7 Reused (11) Main IC : LGE107_Mstar Tuner Type : TDTJ-S001D (DVB-T/C) Display Type (Resolution) : 3D, LED TV (1920 x 1080) Interface : HDMI 3EA , Component 1EA, AV 1EA, USB 1EA Difference : HDMI Position , Interface, Wafer Position (LVDS, Power, Sub)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

7/22

LGE Internal Use Only

Block diagram
Tuner_SIF 41P 51P 30P FRC DDR3 X 16 X 1 (1Gb X 1) SPI Flash(2Mb) Only for FRC or 3D Model SYSTEM DDR3 X 16 X2 (1Gb) DATA Video Audio

TUNER (T/C)

Tuner_CVBS SCL/SDA
FE_TS_DATA[0]/CLK/Valid/Sync

CI_TS_DATA[7:0]/CLK/Valid/Sync

PCMCIA

CI_DATA[7:0] CI_ADDR[14:0] USB_DM/DP HP_OUT HDMI_TMDS/HPD/CEC

USB H/P

Side

HDMI3

HDMI1 HDMI2 COMP1 A/V1 PC-RGB PC-AUDIO SPDIF

HDMI_TMDS/HPD/CEC HDMI_TMDS/HPD/CEC COMP_ YPbPr/ LR_IN AV_CVBS/LR_IN DSUB_RGB/ HVsync DDC_SDA/UART_TX PC_ Audio IN SPDIF_OUT SC_CVBS/RGB/LR_IN

LGE101 (S7) LGE107 (S7+FRC)

SPI Flash(8Mb) NAND Flash(1Gb)


SCL/SDA

SYSTEM EEPROM X 1 (1Mb) HDCP EEPROM X 1 (8Kb) Sub Micom (NEC)

SCL/SDA

SCART

SC_VIDEO/LR_OUT Debug _TX/RX

I2S_I/F SCL/SDA

Rear

RS-232C

Audio AMP

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

8/22

LGE Internal Use Only

Interconnection - 1
19/22LV2500
1

[PCBs]
Main PCB Soft Touch Key/IR PCB

2 1 LED driver

3 1

[Cables]
4
1 2

Soft Touch key/IR cable Main / Module LVDS cable LED driver / Module cable SPK cable

2
3 4

LCD Module

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

9/22

LGE Internal Use Only

Interconnection - 2
19/22LV5500
1

[PCBs]
Main PCB Soft Touch Key/IR PCB

2 1 LED driver

3 1

[Cables]
4
1 2

Soft Touch key/IR cable Main / Module LVDS cable LED driver / Module cable SPK cable

2 LCD Module

3 4

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

10/22

LGE Internal Use Only

Interconnection - 3
26LV2500
1 2

[PCBs]
Main PCB Soft Touch Key/IR PCB

LED driver 3

2 1

[Cables]
4
1 2

Soft Touch key/IR cable Main / Module LVDS cable LED driver / Module cable SPK cable

2 LCD Module

3 4

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

11/22

LGE Internal Use Only

Interconnection - 4
26LV5500
1 2

[PCBs]
Main PCB Soft Touch Key/IR PCB

LED driver 2 3 1

[Cables]
4
1 2

Soft Touch key/IR cable Main / Module LVDS cable LED driver / Module cable SPK cable

2 LCD Module

3 4

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

12/22

LGE Internal Use Only

Interconnection - 5
32LV2500
1

[PCBs]
Main PCB PSU Soft Touch Key/IR PCB Timing controller LED Driver

3 1 1 5 6 2

2 3

4 5

4 5

[Cables]
1 2

Main / PSU cable Main / Module LVDS cable LED driver / Module cable SPK cable Soft Touch key/IR cable LED driver / PSU cable 14P

3 LCD Module
3 4 5 6

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

13/22

LGE Internal Use Only

Interconnection - 6
37LV3400
1

[PCBs]
Main PCB PSU Soft Touch Key/IR PCB Timing controller LED Driver

3 1 5 2 6 1

2 3

4 5

4 5

[Cables]
1 2

Main / PSU cable Main / Module LVDS cable LED driver / Module cable SPK cable Soft Touch key/IR cable LED driver / PSU cable 14P

3 LCD Module
3 4 5 6

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

14/22

LGE Internal Use Only

Interconnection - 7
37LV3550
1

[PCBs]
Main PCB PSU Soft Touch Key/IR PCB Timing controller LED Driver

3 2 6 5 1 1

2 3

4 5

2 4 4 5
1 2

[Cables]
Main / PSU cable Main / Module LVDS cable LED driver / Module cable SPK cable Soft Touch key/IR cable LED driver / PSU cable 14P

3 LCD Module
3 4 5 6

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

15/22

LGE Internal Use Only

Interconnection - 8
42LV4500
1

[PCBs]
Main PCB PSU + LED driver Soft Touch Key/IR PCB Timing controller

3 1 1 2

2 3

2 4 5 4

[Cables]
1 2

Main / PSU cable Main / Module LVDS cable LED driver / Module cable SPK cable Soft Touch key/IR cable

3 LCD Module
3 4 5

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

16/22

LGE Internal Use Only

Interconnection - 9
42LW4500
1

[PCBs]
Main PCB PSU + LED driver Soft Touch Key/IR PCB Timing controller

3 1 6 2 1

2 3

2 4 4 5

[Cables]
1 2

Main / PSU cable Main / Module LVDS cable LED driver / Module cable SPK cable Soft Touch key/IR cable Local dimming signal cable (Main / LED driver 8pin)
LGE Internal Use Only

3 LCD Module
3 4 5

6
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

17/22

Interconnection - 10
32LK530
1

[PCBs]
Main PCB PSU (without inverter) IR & Indicator PCB Local Key PCB Inverter Timing controller

6 5 2 1 1

2 3 4 5

2 5

4 3 3 LCD Module

[Cables]
1 2 3 4 5

Main / PSU cable Main / Module LVDS cable SPK cable IR/Local key cable Inverter/PSU cable (14pin)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

18/22

LGE Internal Use Only

Interconnection - 11
37LK430
1

[PCBs]
Main PCB PSU (without inverter) IR & Indicator PCB Local Key PCB Timing controller

5 2 1 1

2 3 4 5

4 4 3 3 LCD Module

[Cables]
1 2 3 4

Main / PSU cable Main / Module LVDS cable SPK cable IR/Local key cable

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

19/22

LGE Internal Use Only

Interconnection - 12
42LK450
1

[PCBs]
Main PCB PSU (without inverter) Soft Touch Key/IR PCB Inverter Timing controller

2 3

2 2 5

1 1

4 5

4 3

[Cables]
1 2

Main / PSU cable Main / Module LVDS cable SPK cable Soft Touch key/IR cable Inverter/PSU cable (14pin)

3 LCD Module
3 4 5

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

20/22

LGE Internal Use Only

Interconnection sub PCB( LV**/LK450 Series )

SPK unit

Soft Touch Key/IR PCB 15pin Cable

To Main

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

21/22

LGE Internal Use Only

Interconnection sub PCB( LK430/LK530 Series )

SPK unit

SPK unit Tact key IR/Sensor To Main

12pin Cable

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

22/22

LGE Internal Use Only

Contents of LCD TV Standard Repair Process


No. 1 2 3 4 5 6 B. Power error 7 8 C. Audio error 9 10 D. Function error 11 12 13 E. Noise F. Exterior error Wrecked audio/discontinuation/noise No response in remote controller, key error, recording error, memory error External device recognition error Circuit noise, mechanical noise Exterior defect 9 10 11 12 13 A. Video error Error symptom (High category) Error symptom (Mid category) No video/Normal audio No video/No audio Video error, video lag/stop Color error Vertical/Horizontal bar, residual image, light spot, external device color error No power Off when on, off while viewing, power auto on/off No audio/Normal video Page 1 2 3 4 5 6 7 8 Remarks

First of all, Check whether there is SVC Bulletin in GCSC System for these model.
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

A. Video error
No video/ Normal audio

Established date Revised date

2010. 2 .19 1/13

First of all, Check whether all of cables between board is inserted properly or not.
(Main B/D Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)
A1
No video Normal audio Normal audio N Move to No video/No audio Y Check Back Light On with naked eye On Y

A4
Check Power Board 12v,3.5v etc. Normal voltage N Repair Power Board or parts Y Replace T-con Board or module

A2

Check Power Board 20V /12V or 24v output

Normal voltage N Repair Power Board or parts

Replace Inverter or module End

Precaution

A7 & A3
Replace Main Board Re-enter White Balance value

Always check & record S/W Version and White Balance value before replacing the Main Board

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

A. Video error
No video/ No audio

Established date Revised date

2010. 2 .19 2/13

A4
No Video/ No audio Check various voltages of Power Board ( 3.5V,12V,20V or 24V) Normal voltage? N Replace Power Board and repair parts Y Check and replace MAIN B/D End

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

A. Picture Problem
Picture broken/ Freezing

Established date Revised date

2010. 2 .19 3/13

A6
Check RF Signal level

. By using Digital signal level meter . By using Diagnostics menu on OSD ( MenuRed keySignal test) - Signal strength (Normal : over 50%) - Signal Quality (Normal: over 50%)

Normal Signal? N

Check whether other equipments have problem or not. (By connecting RF Cable at other equipment) DVD Player ,Set-Top-Box, Different maker TV etc`

Check RF Cable Connection 1. Reconnection 2. Install Booster

A7
Normal Picture? N Y Check S/W Version SVC Bulletin? Y S/W Upgrade Contact with signal distributor or broadcaster (Cable or Air) Normal Picture? Y N N Check Tuner soldering Normal Picture? N Replace Main B/D Y Close

Normal Picture? Y

Close Close

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

A. Video error
Color error

Established date Revised date

2010. 2 .19 4/13

A8
Check color by input -External Input -COMPONENT -RGB -HDMI/DVI

A10/ A11
Color error? N Check error color input mode Y Check and replace Link Cable (LVDS) and contact condition Y Color error? N End Y Replace Main B/D Color error? N Replace module

A12
Check Test pattern

External Input/ Component error

Check external device and cable

External device Y /Cable normal N Request repair for external device/cable N

Replace Main B/D

RGB/ HDMI/DVI error

Check external device and cable

External device Y /Cable normal

Replace Main B/D

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

A. Video error
Vertical / Horizontal bar, residual image, light spot, external device color error

Established date Revised date

2010. 2 .19 5/13

Vertical/Horizontal bar, residual image, light spot


A8
Check color condition by input -External Input -Component -RGB -HDMI/DVI Screen Y normal? N Replace module Check external device connection condition Y Normal? N Request repair for external device

Replace Module

A10/ A11
Check and replace Link Cable Screen N normal? Replace Main B/D

N Screen normal? Y End

Y End

A12
Check Test pattern

External device screen error-Color error


Check S/W Version Check N version Y S/W Upgrade Check screen condition by input -External Input -Component -RGB -HDMI/DVI External Input error Component error

Connect other external device and cable


(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

N Screen normal? Y Request repair for external device Y Screen normal? N Replace Main B/D Replace Main B/D

Normal screen? Y

RGB error

Connect other external device and cable


(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

End
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

HDMI/ DVI

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

B. Power error
No power

Established date Revised date

2010. 2 .19 6/13

A17
Check Power LED Power LED On? N Check Power cord was inserted properly Y DC Power on by pressing Power Key On Remote control Normal N operation? Y

A19
Check Power On High OK?
N

Replace Power B/D

. Stand-By: Red . Operating: white

Replace Main B/D

A4
N Normal? Measure voltage of each output of Power B/D

Close

Check ST-BY 5V

Y Normal Y voltage?

Normal voltage? N

Replace Main B/D

A18
N

Replace Power B/D

Replace Power B/D

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

B. Power error
Off when on, off while viewing, power auto on/off

Established date Revised date

2010. 2 .19 7/13

Check outlet

A22
Check A/C cord Error? N Check Power Off Mode CPU Abnormal Replace Main B/D Normal? N Check for all 3- phase power out Y Abnormal 1 Replace Power B/D Y End

Fix A/C cord & Outlet and check each 3 phase out

A19
(If Power Off mode is not displayed) Check Power B/D voltage
Caution Check and fix exterior of Power B/D Part

Normal voltage? N

Replace Main B/D

Replace Power B/D

* Please refer to the all cases which can be displayed on power off mode.

Power off List "POWEROFF_REMOTEKEY" "POWEROFF_OFFTIMER" "POWEROFF_SLEEPTIMER" "POWEROFF_INSTOP" "POWEROFF_AUTOOFF" Normal "POWEROFF_ONTIMER" "POWEROFF_RS232C" "POWEROFF_RESREC" "POWEROFF_RECEND" "POWEROFF_SWDOWN" "POWEROFF_UNKNOWN" "POWEROFF_ABNORMAL1" Abnormal "POWEROFF_CPUABNORMAL"

Status

Explanation Power off by REMOTE CONTROL Power off by OFF TIMER Power off by SLEEP TIMER Power off by INSTOP KEY Power off by AUTO OFF Power off by ON TIMER Power off by RS232C Power off by Reservated Record Power off by End of Recording Power off by S/W Download Power off by unknown status except listed case Power off by abnormal status except CPU trouble Power off by CPU Abnormal
LGE Internal Use Only

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Standard Repair Process

LCD TV

Error symptom

C. Audio error
No audio/ Normal video

Established date Revised date

2010. 2 .19 8/13

A24
No audio Screen normal Check user menu > Speaker off N Off Y Cancel OFF

A25
Check audio B+ 20V or 24V of Power Board Normal voltage N Replace Power Board and repair parts Y

Check Speaker disconnection

N Disconnection Replace MAIN Board End

Y Replace Speaker

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

C. Audio error
Wrecked audio/ discontinuation/noise

Established date Revised date

2010. 2 .19 9/13

abnormal audio/discontinuation/noise is same after Check input signal compared to No audio A25
Wrecked audio/ Discontinuation/ Noise for all audio Signal normal? N Y Wrecked audio/ Discontinuation/ Noise only for D-TV Wrecked audio/ Discontinuation/ Noise only for Analog (When RF signal is not received) Request repair to external cable/ANT provider (In case of External Input signal error) Check and fix external device Normal voltage? N Check and replace speaker and connector Check audio B+ Voltage (20V or 24V) Y

Check input signal -RF -External Input signal

Replace Main B/D

Replace Power B/D

Wrecked audio/ Discontinuation/ Noise only for External Input Connect and check other external device Normal audio? Y

Replace Main B/D

End

Check and fix external device

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

D. General Function Problem


Remote control & Local switch checking

Established date Revised date

2010. 2 .19 10/13 Replace Main B/D

1. Remote control(R/C) operating error


A27
Check R/C itself Operation Normal Y operating? N Check R/C Operating When turn off light in room If R/C operate, Explain the customer cause is interference from light in room. Check & Replace Baterry of R/C Check & Repair Cable connection Connector solder Normal operating? Y Close N

A27
Check voltage On Main B/D Normal Voltage? N Y

A27
Check IR Output signal Normal Signal? N Repair/Replace IR B/D Y

A4

Check 5v on Power B/D Replace Power B/D or Replace Main B/D (Power B/D dont have problem)

Normal operating? N Replace R/C

Close

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

10

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

D. Function error
External device recognition error

Established date Revised date

2010. 2 .19 11/13

Check input signal

Y Signal input? N

Check technical information - Fix information - S/W Version

Technical information? Y

External Input and Component Recognition error

Replace Main B/D

Check and fix external device/cable

Fix in accordance with technical information

RGB,HDMI/ DVI, Optical Recognition error

Replace Main B/D

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

11

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

E. Noise
Circuit noise, mechanical noise

Established date Revised date

2010. 2 .19 12/13

Identify nose type

Circuit noise

Check location of noise

Replace PSU(with LED driver) OR Replace LED driver

Mechanical noise

Check location of noise When the nose is severe, replace the module (For models with fix information, upgrade the S/W or provide the description)
OR

Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage. Describe the basis of the description in Part related to nose in the Owners Manual.

OR

If there is a Tak Tak noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual (For models without any fix information, provide the description)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

12

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

F. Exterior defect
Exterior defect

Established date Revised date

2010. 2 .19 13/13

Zoom part with exterior damage

Module damage

Replace module

Cabinet damage Remote controller damage

Replace cabinet

Replace remote controller

Stand dent

Replace stand

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

13

LGE Internal Use Only

Contents of LCD TV Standard Repair Process Detail Technical Manual


No. 1 2 A. Video error_ No video/Normal audio 3 4 6 A. Video error_ No video/Video lag/stop 7 9 10 A. Video error_Color error 11 12 13 14 15 16 17 18 19 20 <Appendix> Defected Type caused by T-Con/ Inverter/ Module A. Video error_Vertical/Horizontal bar, residual image, light spot LCD-TV Version checking method LCD TV connection diagram Tuner Checking Part Check Link Cable (LVDS) reconnection condition Adjustment Test pattern - ADJ Key LCD TV connection diagram Check Link Cable (LVDS) reconnection condition Adjustment Test pattern - ADJ Key Exchange T-Con Board (1) Exchange T-Con Board (2) Exchange LED driver Board (PSU) Exchange Module itself (1) Exchange Module itself (2) A7 A8 A9 A10 A11 A12 A8 A10 A11 A12 A-1/5 A-2/5 A-3/5 A-4/5 A-5/5 A10 : Edge LED A11 : Lamp A10 : Edge LED A11 : Lamp Check White Balance value Power Board voltage measuring method TUNER input signal strength checking method A3 A4 A6 Error symptom Content Check LCD back light with naked eye LED driver B+ 24V measuring method Page A1 A2 Remarks

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Continue to the next page


LGE Internal Use Only

Contents of LCD TV Standard Repair Process Detail Technical Manual


Continued from previous page
No. 21 22 23 24 25 26 27 28 C. Audio error_No audio/Normal video 29 30 31 C. Audio error_Wrecked audio/discontinuation D. Function error_ No response in remote controller, key error Voltage and speaker checking method when there is no audio Voltage and speaker checking method in case of audio error Remote controller operation checking method A25 A25 A27 B. Power error_Off when on, off while viewing B. Power error_Off when on, off while viewing POWER OFF MODE checking method POWER BOARD PIN voltage checking method Checking method in menu when there is no audio A22 A19 A24 B. Power error_No power Error symptom Content Check front display LED Check power input Voltage & ST-BY 5V Checking method when power is ON POWER BOARD voltage measuring method Page A17 A18 A19 A4 Remarks

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

A. Video error_No video/Normal audio


Check LCD back light with naked eye

Established date Revised date

2011. 2 .07 A1

After turning on the power and disassembling the case, check with the naked eye, whether you can see light from 4 locations.
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A1

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

A. Video error_No video/Normal audio

Established date Revised LED driver/lamp inverter B+ 24V measuring method date

2011. 2 .07 A2

Check the DC 24V, 12V, 3.5V and Inverter on

Edge LED PSU without LED Driver

* 26 ~ 47 : `11 Pin map Lamp (Power Board Inverter) - PSU


14 Pin 1~5 6 ~ 10 11 12 24V GND Detect Inverter On/Off Int. PWM Ext. PWM (PDIM)
LGE Internal Use Only

Lamp PSU without inverter


Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

13 14

A2

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

A. Video error_No video/Normal audio


Check White Balance value

Established date Revised date

2011. 2 .07 A3

Entry method Entry method 1. Press the ADJ button on the remote controller for adjustment. 1. Press the ADJ button on the remote controller for adjustment. 2. Enter into White Balance of item 6. 2. Enter into White Balance of item 7. 3. After recording the R, G, B (GAIN, Cut) value of Color Temp 3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re-enter the value after replacing the MAIN BOARD. (Cool/Medium/Warm), re-enter the value after replacing the MAIN BOARD.
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A3

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

A. Video error_No video/ Audio


Power Board voltage measuring method

Established date Revised date

2011. 2 .07 A4

Check the DC 20Vor24V, 12V, 3.5V.


24 Pin (Power Board Main Board) FW20020-24SB (FOOSUNG) 1 3 5 7 Power on 20V (24V) GND GND 3.5V 3.5V GND GND 12V 12V 12V N.C 2 4 6 8 10 12 14 16 18 20 22 24 20V (24V) 20V (24V) GND GND 3.5V 3.5V GND GND Inverter On/off Lamp : A-Dim PWM Dim #1 Error-out

Edge LED PSU without LED Driver

9 11 13 15 17 19 21 23

Lamp PSU without inverter


Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A4

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

A. Video error_Video error, video lag/stop


TUNER input signal strength checking method

Established date Revised date

2011. 2 .07 A6

MENU - red key(customer support - select channel

signal test

When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.)

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A6

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

A. Video error_Video error, video lag/stop


LCD-TV Version checking method

Established date Revised date

2011. 2 .07 A7

1. Checking method for remote controller for adjustment

Version

Press the IN-START with the remote controller for adjustment


Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A7

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

A. Video error _Vertical/Horizontal bar, residual image, light spot


LCD TV connection diagram (1)

Established date Revised date

2011. 2 .07 A8

As the part connecting to the external input, check the screen condition by signal

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A8

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

A. Video error_Video error, video lag/stop


TUNER checking part

Established date Revised date

2011. 2 .07 A9

Checking method: 1. Check the signal strength or check whether the screen is normal when the external device is connected. 2. After measuring each voltage from power supply, finally replace the MAIN BOARD.

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A9

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

A. Video error_Color error


Check Link Cable (LVDS) reconnection condition

Established date Revised date

2011. 2 .07 A10

<LV** : Edge LED Series Models>

Check the contact condition of the Link Cable, especially dust or mis insertion.
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A10

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

A. Video error_Color error


Check Link Cable (LVDS) reconnection condition

Established date Revised date

2011. 2 .07 A11

<LK** : Lamp series Models>

Check the contact condition of the Link Cable


Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A11

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

A. Video error_Color error


Adjustment Test pattern - ADJ Key

Established date Revised date

2011. 2 .07 A12

You can view 6 types of patterns using the ADJ Key Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..) 4.Video error (Classification of MODULE or Main-B/D!)
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A12

LGE Internal Use Only

Appendix : Exchange T-Con Board (1)

Solder defect, CNT Broken

Solder defect, CNT Broken

Solder defect, CNT Broken

Solder defect, CNT Broken

T-Con Defect, CNT Broken T-Con Defect, CNT Broken Solder defect, CNT Broken T-Con Defect, CNT Broken

Abnormal Power Section

Solder defect, Short/Crack


Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Abnormal Power Section A - 1/5

Solder defect, Short/Crack


LGE Internal Use Only

Appendix : Exchange T-Con Board (2)

Abnormal Power Section

Abnormal Power Section

Solder defect, Short/Crack

Solder defect, Short/Crack

Fuse Open, Abnormal power section

Abnormal Display

GRADATION
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Noise A - 2/5

GRADATION
LGE Internal Use Only

Appendix : Exchange PSU(LED driver)

No Light

Dim Light

Dim Light

Dim Light

No picture/Sound Ok
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A 3/5

LGE Internal Use Only

Appendix : Exchange the Module (1)

Panel Mura, Light leakage

Panel Mura, Light leakage

Press damage

Crosstalk

Press damage

Crosstalk

Un-repairable Cases In this case please exchange the module.

Press damage
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A 4/5

LGE Internal Use Only

Appendix : Exchange the Module (2)

Vertical Block Source TAB IC Defect

Vertical Line Source TAB IC Defect

Vertical Block Source TAB IC Defect

Horizontal Block Gate TAB IC Defect

Horizontal Block Gate TAB IC Defect Gate TAB IC Defect

Horizontal line Gate TAB IC Defect Gate TAB IC Defect

Un-repairable Cases In this case please exchange the module.


Horizontal Block Gate TAB IC Defect Gate TAB IC Defect
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A 5/5

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

B. Power error _No power


Check front display LED

Established date Revised date

2010. 2 .19 A17

Front LED control : Menu Option Power Indicator Standby light ON

ST-BY condition: Red Power ON condition: white

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A17

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

B. Power error _No power


Check power input voltage and ST-BY 3.5V

Established date Revised date

2011. 2 .07 A18

For 11 models, there is no voltage out for st-by purpose. When st-by, only 3.5V is normally on.
Check the 3.5V when st-by
24 Pin (Power Board Main Board) FW20020-24SB (FOOSUNG) 1 3 5 7 Power on 20V (24V) GND GND 3.5V 3.5V GND GND 12V 12V 12V N.C 2 4 6 8 10 12 14 16 18 20 22 24 20V (24V) 20V (24V) GND GND 3.5V 3.5V GND GND Inverter On/off Lamp : A-Dim PWM Dim #1 Error-out

Edge LED PSU without LED Driver

9 11 13 15 17 19 21 23

Lamp PSU without inverter


Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A18

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
Error symptom Content

B. Power error _No power


Checking method when power is ON

Established date Revised date

2011. 2 .07 A19

Check power on pin is high


24 Pin (Power Board Main Board) FW20020-24SB (FOOSUNG) 1 3 5 7 Power on 20V (24V) GND GND 3.5V 3.5V GND GND 12V 12V 12V N.C 2 4 6 8 10 12 14 16 18 20 22 24 20V (24V) 20V (24V) GND GND 3.5V 3.5V GND GND Inverter On/off Lamp : A-Dim PWM Dim #1 Error-out

Edge LED PSU without LED Driver

9 11 13 15 17 19 21 23

Lamp PSU without inverter


Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A19

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

B. Power error _Off when on, off whiling viewing Established


POWER OFF MODE checking method date Revised date

2011. 2 .07 A22

Entry method 1. Press the IN-START button of the remote controller for adjustment 2. Check the entry into adjustment item 3

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A22

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

C. Audio error_No audio/Normal video


Checking method in menu when there is no audio

Established date Revised date

2011. 2 .07 A24

Checking method
1. Press the MENU button on the remote controller 2. Select the AUDIO function of the Menu 3. Select TV Speaker from Off to On

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A24

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
Error symptom Content

C. Audio error_No audio/Normal video


Voltage and speaker checking method when there is no audio

Established date Revised date

2011. 2 .07 A25

Edge LED PSU without LED Driver

Checking order when there is no audio Check the contact condition of 20V or 24V connector of Main Board Measure the 24V input voltage supplied from Power Board (If there is no input voltage, remove and check the connector) Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the GND and output terminal, the speaker is normal.

Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A25

LGE Internal Use Only

Standard Repair Process Detail Technical Manual


LCD TV
<ALL MODELS>
P2401, P2402 EYEQ_SCL EYEQ_SDA GND KEY1 KEY2 St 3.3V GND LED_B IR GND Normal 3.3V LED_R GND Soft Touch_SCL Soft Touch_SDA Error D. Function error_ No response in remote controller, symptom key error Content Remote controller operation checking method Established date Revised date 2011. 2 .07 A27

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2

Checking order 1, 2. Check IR cable condition between IR & Main board. 3. Check the st-by 3.3V on the terminal 6. 4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog Tester needle moves slowly, and defective when it does not move at all.
Copyright 2011 LG Electronics. Inc. All rights reserved. Only for training and service purposes

A27

LGE Internal Use Only

You might also like