Scribd
Upload
365 views14 pages

Commodore 1902A Monitor

Uploaded by

dallos
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
365 views14 pages

Commodore 1902A Monitor

Uploaded by

dallos
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 14
RGB INTERFACE P.C. BOARD (viewed from the component side) CRT P.C. BOARD (viewed from the component side) “3438 5.03, 30605» gi, MAIN P.C. BOARD (viewed from the component side) 902A SERVICE MANUAL ADJUSTMENT PROCEDURES Adjustmant Notes: funtess otherwise spacitiga:! t. Anisolation transformer must ha used when servicing this unit, 2. Line voltage maintained at TZOVAC, 60Hz. 3. The unit should be allowed to warm up for at least 30 minutes prior to making ary adjustments. 4. Voltages measured with respect to ground. 3. Signal injection point is tha Video In Jack. Power Supply Adjuatmant 1. With the unit off, set the Volume Contral {R316}, Contrast Control (R585), and Brightness Control {R589} to minimum. Praset A114 to mechanical center. Connect a voltmeter across C494 and turn on the unit. 4. Adjust R114 for a reading of 125¥V on the meter. Ah Horizonta! Synchronization Adjustmant 1. Inject 4 cross-hatch pattern signal and short C434. 2. Adjust the horizontal syne with A437. 3. Remove tha short fram C434, Vertical Synchronization Adjustment 1. Inject a cross-hatch pattern signal and short C434, 2. Adjust the vartical sync with R331, 3. Remove the short from C434. Horizontal Amplitude and Centering Adjustment 1. Inject a cross-hatch Pattern signal and set the Brightness Controt (R589) and Contrast Con- trol (R585) to their mechanical centers, 2. Adjust R485 so that 14 blocks correspond to @ width of 28cm. 3. Adjust R453 te center the display horizontatty, Vertical Amplitude and Centering Adjustment 1. Inject a cross-hatech pattern signal and sat the Brightness Contro! (R589) and Contrast Con- tral (R585) to their mechanical centers. 2. Adjust R353 so that 10 blocks carrespond to a height of 18.5em. 3. Adjust R364 to center the display verticaily, Chrominanece Adjustment 1. Inject a color bar Pattern signal and adjust the secondary controls for normal viewing. Place SK3 inct used in CM8562} in the off position. #, Connect an oscilloscope to pin 15 of C502 and adjust $533 for minimum amplitude of the chrominance signal that is present on the various brightness steps of the luminance signal. 3. Short pins 9 and 17 of IC561. 4. Adjust C567 to minimize the chroma aS Visi- ble on the screen, 9. Remove the shorting clips from pins 9 and 17. Comb Fliter Adjustment 1. Inject a color bar pattern signal and place the Comb Filter Switch (SK3) in the on position, 2. Connect an oscilloscope to the emitter of T5531 and adjust R523 and $515 for minimum amplitude of the chrominance Signal. For optimum performance, repeat the adjustment. Focus Adjustmant t. Inject a cross-hatch Pattern signal and set the Brightness Control (R589) to minimum and the Contrast Contral { R585) to maximum. 2. Adjust R732 for optimum focus, X-Ray Protection Circuit Adjustment 1. Inject a color bar Pattern signal snd set the Brightness and Contrast Controls te minimum. 2. Connect a voltmeter between the wiper af R457 and ground. 3. Adjust R457 for a reading of 6.9V. NOTE: The following adjustments need only be Parformed if the CRT has been replaced. Minor corrections far purity and convergence may be accomplished through the use of the Purity and Convergence Assambly located on tha neck of the CRT.

You might also like