Scribd Logo
Upload

Welcome to Scribd!

  • 2K views

    Aisi 4140 En8 En19

    Uploaded by

    Jose Kurian
    AISI 4140 is a chromium molybdenum alloy steel that is supplied in the hardened and tempered condition between 18-22HRc. It offers good ductility, shock resistance, and wear resistance. AISI 4140 is suitable for applications in the oil and gas sector. EN8 is an unalloyed medium carbon steel with good tensile strength that is normally supplied in cold drawn or as rolled form between 500-800 N/mm2. It can be hardened through heating to 830/860°C and quenching, then tempered between 550-660°C.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd

    Aisi 4140 En8 En19

    Uploaded by

    Jose Kurian
    2K views1 page
    AISI 4140 is a chromium molybdenum alloy steel that is supplied in the hardened and tempered condition between 18-22HRc. It offers good ductility, shock resistance, and wear resistance. AISI 4140 is suitable for applications in the oil and gas sector. EN8 is an unalloyed medium carbon steel with good tensile strength that is normally supplied in cold drawn or as rolled form between 500-800 N/mm2. It can be hardened through heating to 830/860°C and quenching, then tempered between 550-660°C.

    Original Title

    AISI 4140 EN8 EN19

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    AISI 4140 is a chromium molybdenum alloy steel that is supplied in the hardened and tempered condition between 18-22HRc. It offers good ductility, shock resistance, and wear resistance. AISI 4140 is suitable for applications in the oil and gas sector. EN8 is an unalloyed medium carbon steel with good tensile strength that is normally supplied in cold drawn or as rolled form between 500-800 N/mm2. It can be hardened through heating to 830/860°C and quenching, then tempered between 550-660°C.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    2K views1 page

    Aisi 4140 En8 En19

    Uploaded by

    Jose Kurian
    AISI 4140 is a chromium molybdenum alloy steel that is supplied in the hardened and tempered condition between 18-22HRc. It offers good ductility, shock resistance, and wear resistance. AISI 4140 is suitable for applications in the oil and gas sector. EN8 is an unalloyed medium carbon steel with good tensile strength that is normally supplied in cold drawn or as rolled form between 500-800 N/mm2. It can be hardened through heating to 830/860°C and quenching, then tempered between 550-660°C.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 1

    AISI 4140

    Technical Data

    AISI 4140 is a chromium molybdenum quality alloy steel. AISI 4140 is primarily supplied in the hardened and tempered condition to 18-22HRc range. AISI 4140 offers good ductility, shock resisting characteristics combined with resistancee to wear. AISI 4140 is suitable for a variety of applications in the oil and gas sector. This material can be supplied to AISI stee standards TYPICAL ANALYSIS C. Si. Mn. Cr. Mo. 0.40% 0.25% 0.85% 1.00% 0.25%

    AISI 4140 18-22HRc Typical Mechanical Properties


    Yield (psi) min 80k max 110k UTS (psi) min 100k % Elongation min 20% % Reduction of Area min 40% Hardness HRC 18-22 Charpy room temperature (average of 3) 50J

    EN8

    Technical Data

    EN8 is an unalloyed medium carbon steel with good tensile strength. It is normally supplied in cold drawn or as rolled. Tensile properties can vary but are usually between 500-800 N/mm2. EN8 is available from stock in bar and can be cut to your requirements. We also offer EN8 plate flame cut to your required sizes and normalised. TYPICAL ANALYSIS C. Si. Mn. 0.40% 0.25% 0.80%

    S. 0.015%

    P. 0.015%

    Hardening:
    Heat uniformly to 830/860C until heated through. Quench in oil or water. Can also be induction or flame hardened. Tempering: Heat uniformly and thoroughly at the selected tempering temperatures, between 550C to 660C and hold at heat for one hour per inch of total thickness. Normalising: Normalise at 830-860C, and cool in air.

    You might also like