EIGRP

Routing Protocols and Concepts Chapter 9

Version 4.0

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

Objectives
     Describe the background and history of Enhanced Interior Gateway Routing Protocol (EIGRP). Examine the basic EIGRP configuration commands and identify their purposes. Calculate the composite metric used by EIGRP. Describe the concepts and operation of DUAL. Describe the uses of additional configuration commands in EIGRP.

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

Introduction

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

EIGRP
 Roots of EIGRP: IGRP
Developed in 1985 to overcome RIPv1s limited hop count Distance vector routing protocol Metrics used by IGRP Bandwidth (used by default) Delay (used by default) Reliability Load Discontinued support starting with IOS 12.2(13)T & 12.2(R1s4)S

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

EIGRP
 EIGRP Message Format  EIGRP Header
Data link frame header - contains source and destination MAC address IP packet header - contains source & destination IP address EIGRP packet header - contains AS number Type/Length/Field - data portion of EIGRP message

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

EIGRP

 EIGRP packet header contains:

Opcode field Autonomous System number

 EIGRP Parameters contain:

Weights Hold time

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

EIGRP

 TLV: IP internal contains

Metric field Subnet mask field Destination field

 TLV: IP external contains

Fields used when external routes are imported into EIGRP routing process

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

EIGRP
 Protocol Dependent Modules (PDM)
EIGRP uses PDM to route several different protocols i.e. IP, IPX & AppleTalk PDMs are responsible for the specific routing task for each network layer protocol

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

EIGRP
 Reliable Transport Protocol (RTP)  Purpose of RTP
Used by EIGRP to transmit and receive EIGRP packets

 Characteristics of RTP
Involves both reliable & unreliable delivery of EIGRP packet
Reliable delivery requires acknowledgment from destination Unreliable delivery does not require an acknowledgement from destination

Packets can be sent

Unicast Multicast Using address 224.0.0.10
2007 Cisco Systems, Inc. All rights reserved. Cisco Public

EIGRP
 EIGRPs 5 Packet Types  Hello packets
Used to discover & form adjacencies with neighbors

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

10

EIGRP
 Update packets
Used to propagate routing information

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

11

EIGRP
 Query packets Used by DUAL for searching for networks Can use Unicast or Multicast  Reply packets Reply packet Can use Unicast only  Acknowledgement packets Used to acknowledge receipt of update, query & reply packets
2007 Cisco Systems, Inc. All rights reserved. Cisco Public

12

EIGRP
 Purpose of Hello Protocol
To discover & establish adjacencies with neighbor routers

 Characteristics of hello protocol

Time interval for sending hello packet Most networks it is every 5 seconds Multipoint non broadcast multiaccess networks Unicast every 60 seconds Holdtime This is the maximum time router should wait before declaring a neighbor down Default holdtime 3 times hello interval
2007 Cisco Systems, Inc. All rights reserved. Cisco Public

13

EIGRP
 EIGRP Bounded Updates
EIGRP only sends update when there is a change in route status Partial update A partial update includes only the route information that has changed the whole routing table is NOT sent Bounded update When a route changes, only those devices that are impacted will be notified of the change EIGRPs use of partial bounded updates minimizes use of bandwidth

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

14

EIGRP
 Diffusing Update Algorithm (DUAL)
Purpose EIGRPs primary method for preventing routing loops Advantage of using DUAL Provides for fast convergence time by keeping a list of loop-free backup routes

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

15

EIGRP
 Administrative Distance (AD)
Defined as the trustworthiness of the source route

 EIGRP default administrative distances

Summary routes = 5 Internal routes = 90 Imported routes = 170

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

16

EIGRP
 Authentication EIGRP can
Encrypt routing information Authenticate routing information

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

17

EIGRP
 Network Topology Topology used is the same as previous chapters with the addition of an ISP router

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

18

EIGRP
 EIGRP will automatically summarize routes at classful boundaries

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

19

Basic EIGRP Configuration

 Autonomous System (AS) & Process IDs
This is a collection of networks under the control of a single authority (reference RFC 1930) AS Numbers are assigned by IANA Entities needing AS numbers ISP Internet Backbone prodiers Institutions connecting to other institutions using AS numbers

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

20

Basic EIGRP Configuration

 EIGRP autonomous system number actually functions as a process ID  Process ID represents an instance of the routing protocol running on a router  Example
Router(config)#router eigrp autonomoussystem

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

21

Basic EIGRP Configuration

 The router eigrp command  The global command that enables eigrp is router eigrp autonomous-system All routers in the EIGRP routing domain must use the same process ID number (autonomous-system
number)

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

22

Basic EIGRP Configuration

 The Network Command  Functions of the network command
Enables interfaces to transmit & receive EIGRP updates Includes network or subnet in EIGRP updates

 Example
Router(config-router)#network network-address

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

23

Basic EIGRP Configuration

 The network Command with a Wildcard Mask This option is used when you want to configure EIGRP to advertise specific subnets Example
Router(config-router)#network network-address [wildcard-mask]

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

24

Basic EIGRP Configuration

 Verifying EIGRP
EIGRP routers must establish adjacencies with their neighbors before any updates can be sent or received Command used to view neighbor table and verify that EIGRP has established adjacencies with neighbors is show ip eigrp neighbors

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

25

EIGRP
 The show ip protocols command is also used to verify that EIGRP is enabled

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

26

Basic EIGRP Configuration

 Examining the Routing Table
The show ip route command is also used to verify EIGRP EIGRP routes are denoted in a routing table by the letter D By default , EIGRP automatically summarizes routes at major network boundary

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

27

Basic EIGRP Configuration

 Introducing the Null0 Summary Route
Null0 is not a physical interface In the routing table summary routes are sourced from Null0 Reason: routes are used for advertisement purposes EIGRP will automatically include a null0 summary route as child route when 2 conditions are met At least one subnet is learned via EIGRP Automatic summarization is enabled

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

28

Basic EIGRP Configuration

 R3s routing table shows that the 172.16.0.0/16 network is automatically summarized by R1 & R3

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

29

EIGRP Metric Calculation

 EIGRP Composite Metric & the K Values
EIGRP uses the following values in its composite metric Bandwidth, delay, reliability, and load The composite metric used by EIGRP Formula used has values K1 K5 K1 & K3 =1 all other K values= 0

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

30

EIGRP Metric Calculation

 Use the sh ip protocols command to verify the K values

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

31

EIGRP Metric Calculation

 EIGRP Metrics
Use the show interfaces command to view metrics EIGRP Metrics Bandwidth EIGRP uses a static bandwidth to calculate metric Most serial interfaces use a default bandwidth value of 1.544Mbos (T1)

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

32

EIGRP Metric Calculation

 EIGRP Metrics Delay is the defined as the measure of time it takes for a packet to traverse a route
It is a static value based on link type to which interface is connected

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

33

EIGRP Metric Calculation

 Reliability (not a default EIGRP metric)
A measure of the likelihood that a link will fail Measure dynamically & expressed as a fraction of 255 the higher the fraction the better the reliability

 Load (not a default EIGRP metric)

A number that reflects how much traffic is using a link Number is determined dynamically and is expressed as a fraction of 255 The lower the fraction the less the load on the link

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

34

EIGRP Metric Calculation

 Using the Bandwidth Command
Modifying the interface bandwidth Use the bandwidth command Example Router(config-if)#bandwidth kilobits Verifying bandwidth Use the show interface command Note bandwidth command does not change the links physical bandwidth

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

35

EIGRP Metric Calculation

 The EIGRP metric can be determined by examining the bandwidth delay

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

36

EIGRP Metric Calculation

 EIGRP uses the lowest bandwidth (BW)in its metric calculation Calculated BW = reference BW / lowest BW(kbps)  Delay EIGRP uses the cumulative sum of all outgoing interfaces Calculated Delay = the sum of outgoing interface delays  EIGRP Metric = calculated BW + calculated delay

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

37

EIGRP Metric Calculation

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

38

DUAL Concepts
 The Diffusing Update Algorithm (DUAL) is used to prevent looping

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

39

DUAL Concepts
 Successor
The best least cost route to a destination found in the routing table

 Feasible distance
The lowest calculated metric along a path to a destination network

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

40

DUAL Concepts
 Feasible Successors, Feasibility Condition & Reported Distance  Feasible Successor
This is a loop free backup route to same destination as successor route

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

41

DUAL Concepts
 Feasible Successors, Feasibility Condition & Reported Distance  Reported distance (RD)
The metric that a router reports to a neighbor about its own cost to that network

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

42

DUAL Concepts
 Feasibility Condition (FC) Met when a neighbors RD is less than the local routers FD to the same destination network

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

43

DUAL Concepts
 Topology Table: Successor & Feasible Successor  EIGRP Topology table
Viewed using the show ip eigrp topology command Contents of table include: all successor routes all feasible successor routes

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

44

DUAL Concepts
 EIGRP Topology Table dissected

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

45

DUAL Concepts
 Topology Table: No Feasible Successor
 A feasible successor may not be present because the feasibility condition may not be met In other words, the reported distance of the neighbor is greater than or equal to the current feasible distance

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

46

DUAL Concepts
 Finite Sate Machine (FSM) An abstract machine that defines a set of possible states something can go through, what event causes those states and what events result form those states FSMs are used to describe how a device, computer program, or routing algorithm will react to a set of input events

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

47

DUAL Concepts
 DUAL FSM Selects a best loopfree path to a destination Selects alternate routes by using information in EIGRP tables

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

48

DUAL Concepts
 Finite State Machines (FSM) To examine output from EIGRPs finite state machine us the debug eigrp fsm command

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

49

More EIGRP Configurations

 The Null0 Summary Route By default, EIGRP uses the Null0 interface to discard any packets that match the parent route but do not match any of the child routes EIGRP automatically includes a null0 summary route as a child route whenever both of the following conditions exist
One or subnets exists that was learned via EIGRP Automatic summarization is enabled

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

50

More EIGRP Configurations

 The Null0 Summary Route

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

51

More EIGRP Configurations

 Disabling Automatic Summarization The auto-summary command permits EIGRP to automatically summarize at major network boundaries The no auto-summary command is used to disable automatic summarization
This causes all EIGRP neighbors to send updates that will not be automatically summarized This will cause changes to appear in both routing tables topology tables

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

52

More EIGRP Configurations

 Manual Summarization Manual summarization can include supernets
Reason: EIGRP is a classless routing protocol & include subnet mask in update

Command used to configure manual summarization

Router(config-if)#ip summary-address eigrp as-number network-address subnet-mask

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

53

More EIGRP Configurations

 Configuring a summary route in EIGRP

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

54

More EIGRP Configurations

 EIGRP Default Routes Quad zero static default route Can be used with any currently supported routing protocol Is usually configured on a router that is connected a network outside the EIGRP domain EIGRP & the Quad zero static default route Requires the use of the redistribute static command to disseminate default route in EIGRP updates

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

55

More EIGRP Configurations

 Fine-Tuning EIGRP EIGRP bandwidth utilization
By default, EIGRP uses only up to 50% of interface bandwidth for EIGRP information The command to change the percentage of bandwidth used by EIGRP is Router(config-if)#ip bandwidth-percent eigrp asnumber percent

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

56

More EIGRP Configurations

 Configuring Hello Intervals and Hold Times
Hello intervals and hold times are configurable on a per-interface basis The command to configure hello interval is Router(config-if)#ip hello-interval eigrp as-number seconds

 Changing the hello interval also requires changing the hold time to a value greater than or equal to the hello interval
The command to configure hold time value is Router(config-if)#ip hold-time eigrp as-number seconds

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

57

Summary
 Background & History
EIGRP is a derivative of IGRP EIGRP is a Cisco proprietary distance vector routing protocol released in 1994

 EIGRP terms and characteristics

EIGPR uses RTP to transmit & receive EIGRP packets EIGRP has 5 packet type: Hello packets Update packets Acknowledgement packets Query packets Reply packets Supports VLSM & CIDR
2007 Cisco Systems, Inc. All rights reserved. Cisco Public

58

Summary
 EIGRP terms and characteristics
EIGRP uses a hello protocol Purpose of hello protocol is to discover & establish adjacencies EIGRP routing updates Aperiodic Partial and bounded Fast convergence

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

59

Summary
 EIGRP commands
The following commands are used for EIGRP configuration RtrA(config)#router eigrp [autonomous-system #] RtrA(config-router)#network network-number The following commands can be used to verify EIGRP Show ip protocols Show ip eigrp neighbors Show ip route

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

60

Summary
 EIGRP metrics include Bandwidth (default) Delay (default) Reliability Load

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

61

Summary
 DUAL
Purpose of DUAL
To prevent routing loops

Successor
Primary route to a destination

Feasible successor
Backup route to a destination

Feasible distance
Lowest calculated metric to a destination

Reported distance
The distance towards a destination as advertised by an upstream neighbor
2007 Cisco Systems, Inc. All rights reserved. Cisco Public

62

Summary
 Choosing the best route After router has received all updates from directly connected neighbors, it can calculate its DUAL 1st metric is calculated for each route 2nd route with lowest metric is designated successor & is placed in routing table 3rd feasible successor is found Criteria for feasible successor: it must have lower reported distance to the destination than the installed routes feasible distance Feasible routes are maintained in topology table
2007 Cisco Systems, Inc. All rights reserved. Cisco Public

63

Summary
 Automatic summarization On by default Summarizes routes on classful boundary Summarization can be disabled using the following command RtrA(config-if)#no auto-summary

2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

64

 2007 Cisco Systems, Inc. All rights reserved.

Cisco Public

65