Parts and Accessories. Installation Instructions.

Auxiliary connector retrofit for external audio sources

Retrofit kit No.

65 12 0 153 502

Installation time The installation time is 1.0 hours, but this may vary depending on the condition of the car and the equipment in it. Important information These installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies. In any event the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge. All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations. To avoid unnecessary extra work and/or costs, if any installation or function problems occur, after a brief troubleshooting session (approx. 0.5 hours), an inquiry is to be sent straight away to the technical parts support via the Aftersales Assistance Portal (ASAP), quoting the chassis number, the part number of the retrofit kit and a precise description of the problem. Before you install the retrofit system, test the control module status with the CIP (coding, customising, programming) test program. If the test detects incorrect statuses in one or more control modules, these must be updated first using the Load software function. After the installation work the retrofit kit must be programmed / coded using DISPlus or GT-1 via the Retrofit/CIP path. Do not archive the hard copy of these installation instructions since daily updates are made by ASAP. All the figures show LHD cars, proceed in exactly the same way on RHD cars. See ASAP for details of the pictograms. Pictograms denotes instructions that draw your attention to special features. denotes the end of the instruction or other text. Subject to technical modifications. Special tools required None

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

Contents
Section 1. 2. 3. 4. 5. 6. 7. Page 3 4 5 6 7 8 9

Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connection diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install and connect the AUX connector wiring harness in E60 and E61 cars . . . . . . . . . . . . To install and connect the AUX connector wiring harness in E63 and E64 cars . . . . . . . . . . . . Concluding work and coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

1.

Parts list

A B C D
Auxiliary Input

061 0115 Z

Legend A B C D AUX connector wiring harness Mounting plate Philips screw (2x) Cable tie (5x)

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

2.

Preparations
TIS No.

Conduct a brief test Disconnect the negative pole of the battery The following components must be removed first of all: Glove box on the right M-ASK/CCC

--12 00 ...

51 16 360 65 83 010

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

3.

Connection diagram

A A1 A2
061 0116 Z
Item A A1 A2 Description AUX connector wiring harness Pawl socket 3.5 mm SW 12-pin socket casing Signal ------Cable colour / Cross-section ------Connection location in the car --In glove compartment Disconnected cables in radio plug X13813 X13813 Abbreviation / Slot -----

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

4.

To install and connect the AUX connector wiring harness in E60 and E61 cars
All holes must be drilled precisely as shown in the illustration. Place the mounting plate B in the glove compartment (1) and mark the position of the holes. Drill the hole (2) with a 9 mm twist drill bit and holes (3) with a 2 mm twist drill bit in the glove compartment.

B 1
Auxiliary Input

060 0453 Z

A1
Auxiliary

B C
Input

Insert branch A1 in the glove compartment (1) and secure it to mounting plate B with a knurled nut (2). Secure mounting plate B to the glove compartment (1) using Philips screws C.

1
Auxiliary

Input

060 0454 Z

X13812

X13813

Disconnect the existing cables from branch A2 and connect them to plug X13813 : - WS/BL cable to PIN 7 - WS/RT cable to PIN 2 - WS/BR cable to PIN 8 Connect plug X13813 to plug X13812.

A2

0630209 Z

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

5.

To install and connect the AUX connector wiring harness in E63 and E64 cars
All holes must be drilled precisely as shown in the illustration.
a

B
Auxiliary Input

Place the mounting plate B in the glove compartment (1) and mark the position of the holes. Dimension a: 10 mm

Drill the hole (2) with a 9 mm twist drill bit and holes (3) with a 2 mm twist drill bit in the glove compartment.
063 0206 Z

Auxiliary Input

Insert branch A1 in the glove compartment (1) and secure it to mounting plate B with a knurled nut (2).

A1
Auxiliary Input

2 B

Secure mounting plate B to the glove compartment (1) using Philips screws C.

1 X13812

C
0630208 Z

X13813

Disconnect the existing cables from branch A2 and connect them to plug X13813 : - WS/BL cable to PIN 7 - WS/RT cable to PIN 2 - WS/BR cable to PIN 8 Connect plug X13813 to plug X13812.

A2

0630209 Z

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

6.

Concluding work and coding

This retrofit system requires coding. - Connect battery - Encode/program the retrofit using DISPlus or GT-1 via path CIP - Conduct a brief test - Conduct a function test: - Connect an external audio source to the pawl socket in the glove compartment - Switch on the ignition and the main menu will appear in the on-board monitor - Slide the controller downwards and select the Entertainment menu point - Turn the controller clockwise, select the AUX menu point and confirm it - Start the playback of the external audio source The volume and sound settings can be adjusted using the radio. If the traffic bulletin feature is active, the audio signals from the external audio source will be interrupted when a traffic bulletin is broadcast. - Re-assemble the car

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004

7.

Circuit diagram

WS/BL 0,35 WS/RT 0,35

C=0,22F R=300k C=0,22F

Audio-R+ Audio-L+

7 2 8
060 0455 Z

A1

1 3

X13813

WS/BR 0,35

Audio-GND

Legend A1 Pawl plug 3.5 mm X13813 SW 12-pin socket casing Cable colours BL BR GE GR SW WS Blue Brown Yellow Grey Black White

BMW AG, Mnchen

EBA-Nr.: 01 29 0 395 827

Stand: 08.2004