Service Manual Service Manual: Digital Video Camera Recorder

DCR-TRV230/TRV330/TRV530
RMT-814
SERVICE MANUAL
US Model
Canadian Model
E Model
Hong Kong Model
Korea Model
Ver 1.2 2005. 06
Tourist Model
DCR-TRV330/TRV530
Argentina Model
DCR-TRV230/TRV530
Brazilian Model
Photo : DCR-TRV530
RMT-814
DCR-TRV330
M2000 MECHANISM
For MECHANISM ADJUSTMENT, refer to the 8mm

Video MECHANICAL ADJUSTMENT MANUAL IX
M2000 MECHANISM (9-929-861-11).
SPECIFICATIONS
Continued on next page
DIGITAL VIDEO CAMERA RECORDER
SUPPLIED ACCESSORIES
Make sure that the following accessories are supplied with your
camcorder.
Abbreviation
HK : Hong Kong model
JE : Tourist model
AR : Argentina model
SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT

LA SCURIT!
LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT
CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY
DONT LES NUMROS SONT DONNS DANS CE MANUEL OU
DANS LES SUPPMENTS PUBLIS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
Check the area of your repair for unsoldered or poorly-soldered

connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs

of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
Keep the temperature of the soldering iron around 270C
during repairing.
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
Be careful not to apply force on the conductor when soldering
or unsoldering.
Table for difference of function

Model
DCR-TRV230
DCR-TRV330
DCR-TRV530
US,CND,E,HK,KR, US,CND,E,HK,KR, US,CND,E,HK,KR,
Destination
AR
JE,BR
JE,AR
2.5 inch
size
3.5 inch
61K
LCD
pixel
123K
TYPE SH
type
TYPE SO
a
Memory stick
a (P)
Intelligent accessory shoe
a
a
DIGITAL IN/OUT (USB)
a
Self-timer recording
CD-
CD-292
CD-315
CF-
CF-079
CF-080
LB-
LB-068
LB-070
SI-
SI-028
SI-029
FU-
FU-150
FU-154
Board
PCPD-
PC-082
PD-138
PD-139
Abbreviation
CND : Canadian model
HK : Hong Kong model
KR : Korea model
JE : Tourist model
BR : Brazilian model
AR : Argentina model
Remark
a: with PC-082 board

a (P): Supports printer
a: with PC-082 board
a: Select of menu
CD-292: 2.5 inch LCD
CD-315: 3.5 inch LCD
CF-079: 2.5 inch LCD
CF-080: 3.5 inch LCD
LB-068: 2.5 inch LCD
LB-070: 3.5 inch LCD
SI-028: 2.5 inch LCD
SI-029: 3.5 inch LCD
FU-150: 2.5 inch LCD
FU-154: 3.5 inch LCD
With Memory stick slot & USB connector
PD-138: 2.5 inch LCD
PD-139: 3.5 inch LCD
TABLE OF CONTENTS
SERVICE NOTE
1.
2.
POWER SUPPLY DURING REPAIRS 8

TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) 8
SELF-DIAGNOSIS FUNCTION
1.
2.
3.
3-1.
3-2.
3-3.
4.
Self-diagnosis Function 9
Self-diagnosis Display 9
Service Mode Display 9
Display Method 9
Switching of Backup No. 9
End of Display 9
Self-diagnosis Code Table 10
1.
GENERAL
Quick Start Guide 1-1

Getting started
Using this manual 1-1
Checking supplied accessories 1-2
Step 1 Preparing the power supply 1-2
Installing the battery pack 1-2
Charging the battery pack 1-2
Connecting to a wall outlet 1-3
Step 2 Setting the date and time 1-3
Step 3 Inserting a cassette 1-4
Recording Basics
Recording a picture 1-4
Shooting backlit subjects BACK LIGHT 1-5
Shooting in the dark NightShot/Super NightShot 1-5
Self-timer recording (DCR-TRV330/TRV530 only) 1-5
Checking the recording END SEARCH/EDITSEARCH/
Rec Review 1-6
Playback Basics
Playing back a tape 1-6
Viewing the recording on TV 1-7
Advanced Recording Operations
Recording a still image on a tape Tape Photo recording 1-7
Using the wide mode 1-8
Using the fader function 1-8
Using special effects Picture effect 1-9
Using special effects Digital effect 1-9
Using the PROGRAM AE function 1-10
Adjusting the exposure manually 1-11
Focusing manually 1-11
Superimposing a title 1-11
Making your own titles 1-12
Inserting a scene 1-12
Advanced Playback Operations
Playing back a tape with picture effects 1-12
Playing back a tape with digital effects 1-13
Enlarging recorded images Tape PB ZOOM 1-13
Quickly locating a scene using the zero set memory function 1-13
Searching a recording by date Date search 1-13
Searching for a photo Photo search/Photo scan 1-14
Editing
Dubbing a tape 1-14
Dubbing only desired scenes Digital program editing 1-15
Using with analog video unit and your computer
Signal convert function 1-18
Recording video or TV programs 1-18
Inserting a scene from a VCR Insert Editing 1-18
Customizing Your Camcorder
Changing the menu settings 1-19
Memory Stick operations (DCR-TRV330/TRV530 only)
Using Memory Stick introduction 1-21
Recording still images on Memory Sticks
Memory Photo recording 1-22
Superimposing a still images in the Memory Stick on an

image MEMORY MIX 1-24
Recording an image from a tape as a still image 1-25
Copying still images from a tape Photo save 1-25
Viewing a still image Memory Photo playback 1-26
Viewing images using your computer 1-27
Copying the image recorded on Memory Stick to tapes 1-28
Enlarging still images recorded on Memory Sticks
Memory PB ZOOM 1-28
Playing back images in a continuous loop SLIDE SHOW 1-29
Preventing accidental erasure Image protection 1-29
Deleting images 1-29
Writing a print mark PRINT MARK 1-30
Using the printer (optional) 1-30
Troubleshooting
Types of trouble and their solutions 1-30
Self-diagnosis display 1-32
Warning indicators and messages 1-32
Additional Information
Digital8 system, recording and playback 1-32
About the InfoLITHIUM battery pack 1-33
About i.LINK 1-33
Using your camcorder abroad 1-34
Maintenance information and precautions 1-34
Quick Reference
Identifying the parts and controls 1-35
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
2-10.
2-12.
2-13.
2-14.
2-15.
2-16.
2-17.
LCD UNIT, PD-138 BOARD (TRV230/TRV330) 2-2

LCD UNIT, PD-139 BOARD (TRV530) 2-3
FRONT PANEL SECTION, SI-028/029 BOARD 2-4
CABINET (R) SECTION 2-5
CF-079 BOARD (TRV230/TRV330) 2-5
CF-080 BOARD (TRV530) 2-6
EVF SECTION, LB-068/070 BOARD 2-7
LENS SECTION, CD-292/315 BOARD 2-8
PC-082 BOARD (TRV330/TRV530) 2-9
BATTERY PANEL SECTION,
BATTERY TERMINAL BOARD 2-10
CONTROL SWITCH BLOCK (SS-1380),
FU-150/154 BOARD 2-10
CABINET (L) SECTION, MECHANISM DECK-1 2-11
VC-254 BOARD 2-12
MECHANISM DECK-2, MD FRAME 2-12
HINGE SECTION 2-14
CIRCUIT BOARDS LOCATION 2-15
FLEXIBLE BOARDS LOCATION 2-16
3.
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
OVERALL BLOCK DIAGRAM (1/5) 3-1

POWER BLOCK DIAGRAM (1/3) 3-11
4.
PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS
2-11.
4-1. FRAME SCHEMATIC DIAGRAM (1/3) 4-1

FRAME SCHEMATIC DIAGRAM (2/3) 4-3
FRAME SCHEMATIC DIAGRAM (3/3) 4-5
4-2. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS 4-8
CD-292 (CCD IMAGER)
PRINTED WIRING BOARD
(DCR-TRV230/TRV330) 4-9
CD-315 (CCD IMAGER)

PRINTED WIRING BOARD (DCR-TRV530) 4-9
CD-292/315 (CCD IMAGER)
SCHEMATIC DIAGRAM 4-10
VC-254 (CAMERA/STD8/Hi8/PB PROCESS,
DV SIGNAL, PB RF AMP, VIDEO IN/OUT,
AD CONVERTER, MODE/CAMERA/MECHA
CONTROL, LASER LINK, DRUM CAPSTAN DRIVE,
AUDIO PROCESS, MIC, DC/DC CONVERTER)
PRINTED WIRING BOARD 4-11
VC-254 (CAMERA PROCESS)(1/18)
VC-254 (CAMERA PROCESS, Hi8/STD8/PB
PROCESS)(2/18)
VC-254 (IRIS/FOCUS/ZOOM DRIVE)(3/18)
VC-254 (DV SIGNAL PROCESS-1)(4/18)
VC-254 (DV SIGNAL PROCESS-2)(5/18)
VC-254 (DIGITAL8 PB RF AMP)(6/18)
VC-254 (VIDEO IN/OUT)(7/18)
VC-254 (VIDEO A/D CONVERTER)(8/18)
VC-254 (Hi8/STD8/PB RF AMP)(9/18)
VC-254 (MODE CONTROL)(10/18)
VC-254 (CAMERA CONTROL, Hi8/STD8 MECHA
CONTROL, STEADY SHOT)(11/18)
VC-254 (EVR, LASER LINK)(12/18)
VC-254 (DIGITAL8 MECHA CONTROL)(13/18)
VC-254 (DRUM/CAPSTAN DRIVE)(14/18)
VC-254 (AUDIO PROCESS)(15/18)
VC-254 (MIC AMP)(16/18)
VC-254 (CONNECTOR)(17/18)
VC-254 (DC/DC CONVERTER)(18/18)
LS-057 (S/T REEL SENSOR), FP-228 (DEW SENSOR),
FP-229 (MODE SWITCH), FP-300 (TAPE TOP),
FP-302 (TAPE END), FP-301 (TAPE LED)
FLEXIBLE BOARDS AND
SCHEMATIC DIAGRAMS 4-51
FP-270 (S VIDEO, AUDIO/VIDEO),
FP-272 (LANC, DV IN/OUT)
FLEXIBLE BOARDS 4-53
PC-082 (DIGITAL STILL CONTROL,
DS STILL PROCESS)
PRINTED WIRING BOARD 4-55
PC-082 (DIGITAL STILL CONTROL 1)(1/3)
PC-082 (DIGITAL STILL CONTROL 2)(2/3)
PC-082 (DS STILL PROCESS)(3/3)
FP-271 (USB), FP-282 (FOCUS), FP-275 (SWITCH)
FLEXIBLE BOARDS 4-65
CF-079 (USER FUNCTION, EVF DRIVE)

(DCR-TRV230/TRV330) 4-67
CF-080 (USER FUNCTION, EVF DRIVE)
CF-079/080 (USER FUNCTION)(1/2)
CF-079/080 (EVF DRIVER)(2/2)
SI-028 (DCR-TRV230/TRV330), SI-029 (DCR-TRV530)
(STEADY SHOT, REMOTE COMMANDER
RECEIVER, LASER LINK)
PRINTED WIRING BOARDS 4-79
FP-273 (MIC, HEADPHONES)
FLEXIBLE BOARD (DCR-TRV530) 4-81
SI-028/029(STEADY SHOT, REMOTE
COMMANDER RECEIVER, LASER LINK)
LB-068 (EVF, BACK LIGHT)
(DCR-TRV230/TRV330) 4-84
LB-070 (EVF, BACK LIGHT)
LB-068/070 (EVF, BACK LIGHT)
FP-283 (PANEL REVERSE)
FLEXIBLE BOARD 4-86
PD-138 (RGB DRIVE, TIMING GENERATOR,
LCD DRIVE, BACK LIGHT DRIVE)
(DCR-TRV230/TRV330) 4-87
PD-138 (RGB DRIVE, TIMING GENERATOR)(1/2)
PD-138 (LCD DRIVE, BACK LIGHT DRIVE)(2/2)
PD-139 (RGB DRIVE, TIMING GENERATOR, LCD
DRIVE, BACK LIGHT DRIVE)
PD-139 (RGB DRIVE, TIMING GENERATOR)(1/2)
PD-139 (LCD DRIVE, BACK LIGHT DRIVE)(2/2)
FU-150 (POWER SUPPLY)
(DCR-TRV230/TRV330) 4-99
FU-154 (POWER SUPPLY)
FU-150/154 (POWER SUPPLY)
4-3. WAVEFORMS 4-103
4-4. MOUNTED PARTS LOCATION 4-107
5.
1.
1-1.
5-1.
1-1.
ADJUSTMENTS
Before starting adjustment 5-2

Adjusting items when replacing main parts and boards 5-2
CAMERA SECTION ADJUSTMENT 5-4
PREPARATIONS BEFORE ADJUSTMENT
(CAMERA SECTION) 5-4
1-1-1. List of Service Tools 5-4
1-1-2. Preparations 5-5
1-1-3. Precaution 5-7
1.
Setting the Switch 5-7
2.
Order of Adjustments 5-7
3.
Subjects 5-7
1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA 5-8
1-2-1. INITIALIZATION OF C, D, 8 PAGE DATA 5-8
1.
Initializing the C, D, 8 Page Data 5-8
2.
Modification of C, D, 8 Page Data 5-8
3.
C Page Table 5-8
4.
D Page Table 5-9
5.
8 Page Table 5-10
1-2-2. INITIALIZATION OF B PAGE DATA
(DCR-TRV330/ TRV530) 5-11
1.
Initializing the B Page Data 5-11
2.
Modification of B Page Data 5-11
3.
B Page Table 5-11
1-2-3. INITIALIZATION OF E, F, 7 PAGE DATA 5-12
1.
Initializing the E, F, 7 Page Data 5-12
2.
Modification of E, F, 7 Page Data 5-12
3.
F Page Table 5-12
4.
E Page Table 5-14
5.
7 Page Table 5-14
1-3. CAMERA SYSTEM ADJUSTMENTS 5-15
1.
HALL Adjustment 5-15
2.
Flange Back Adjustment 5-16
(Using Minipattern Box) 5-16
3.
Flange Back Adjustment
(Using Flange Back Adjustment Chart and Subject More
Than 500m Away) 5-17
3-1. Flange Back Adjustment (1) 5-17
3-2. Flange Back Adjustment (2) 5-17
4.
Flange Back Check 5-18
5.
Optical Axis Adjustment 5-19
6.
Picture Frame Setting 5-20
7.
Color Reproduction Adjustment 5-21
8.
Auto White Balance & LV Standard Data Input 5-22
9.
Auto White Balance Adjustment 5-23
10. White Balance Check 5-24
11. Angular Velocity Sensor Sensitivity Adjustment 5-25
1-4. ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT 5-26
1.
VCO Adjustment (CF-079/080 board) 5-26
2.
RGB AMP Adjustment (CF-079/080 board) 5-27
3.
Contrast Adjustment (CF-079/080 board) 5-27
4.
COM DC Adjustment
(CF-079 board (Part No. suffix: 12 or later))
(CF-080 board (Part No. suffix: 13 or later)) 5-28
1-5. LCD SYSTEM ADJUSTMENT 5-29
1.
VCO Adjustment (PD-138/139 board) 5-30
2.
PSIG Gray Adjustment (PD-139 board)(DCR-TRV530) 5-30
3.
RGB AMP Adjustment (PD-138 board)
(DCR-TRV230/TRV330) 5-31
4.
RGB AMP Adjustment (PD-139 board)(DCR-TRV530) 5-31
5.
Black Limit Adjustment (PD-139 board)(DCR-TRV530) 5-32
6.
Contrast Adjustment (PD-138 board)
(DCR-TRV230/TRV330) 5-32
7.
Contrast Adjustment (PD-139 board)(DCR-TRV530) 5-33
8.
Center Level Adjustment (PD-139 board)(DCR-TRV530) 5-33
9.
COM AMP Adjustment (PD-138 board)
(DCR-TRV230/TRV330) 5-34
10. V-COM Adjustment (PD-138/139 board) 5-34
11. White Balance Adjustment (PD-138/139 board) 5-35
5-2. MECHANISM SECTION ADJUSTMENT 5-36
2-1. Hi8/STANDARD8 MODE 5-36
2-1-1. OPERATING WITHOUT CASSETTE 5-36
2-1-2. TAPE PATH ADJUSTMENT 5-36
1.
Preparations for Adjustment 5-36
2-2. DIGITAL8 MODE 5-37
2-2-1. HOW TO ENTER RECORD MODE WITHOUT
CASSETTE 5-37
2-2-2. HOW TO ENTER PLAYBACK MODE WITHOUT
CASSETTE 5-37
2-2-3. OVERALL TAPE PATH CHECK 5-37
1.
Recording of the tape path check signal 5-37
2.
Tape path check 5-37
5-3. VIDEO SECTION ADJUSTMENT 5-38

3-1. PREPARATIONS BEFORE ADJUSTMENTS 5-38
3-1-1. Equipment to Required 5-38
3-1-2. Precautions on Adjusting 5-39
3-1-3. Adjusting Connectors 5-40
3-1-4. Connecting the Equipment 5-40
3-1-5. Alignment Tape 5-41
3-1-6. Input/output Level and Impedance 5-41
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 5-42
1.
Initialization of B, C, D, E, F, 7, 8 Page Data 5-42
2.
Serial No. Input 5-42
2-1. Company ID Input 5-42
2-2. Serial No. Input 5-42
3-3. SERVO AND RF SYSTEM ADJUSTMENT 5-44
1.
REEL FG Adjustment (VC-254 Board) 5-44
2.
PLL fo & LPF fo Pre-Adjustment (VC-254 Board) 5-44
3.
Switching Position Adjustment (VC-254 Board) 5-45
4.
AGC Center Level and APC & AEQ Adjustment 5-45
4-1. Preparations before adjustments 5-45
4-2. AGC Center Level Adjustment (VC-254 Board) 5-45
4-3. APC & AEQ Adjustment (VC-254 Board) 5-46
4-4. Processing after Completing Adjustments 5-46
5.
PLL fo & LPF fo Fine Adjustment (VC-254 Board) 5-47
6.
Hi8/Standard8 Switching Position Adjustment
(VC-254 Board) 5-47
7.
CAP FG Offset Adjustment (VC-254 board) 5-48
3-4. VIDEO SYSTEM ADJUSTMENTS 5-49
1.
27MHz Origin Oscillation Adjustment (VC-254 board) 5-49
2.
Chroma BPF fo Adjustment (VC-254 Board) 5-49
3.
S VIDEO OUT Y Level Adjustment (VC-254 Board) 5-50
4.
S VIDEO OUT Chroma Level Adjustment(VC-254 Board) 5-50
5.
VIDEO OUT Y, Chroma Level Check (VC-254 Board) 5-51
Hi8/Standard8 Y/C Output Level Setting (VC-254 Board) 5-51
6.
7.
Hi8/standard 8mm AFC fo Adjustment (VC-254 board) 5-52
3-5. IR TRANSMITTER ADJUSTMENTS 5-53
1.
IR Video Carrier Frequency Adjustment (VC-254 board) 5-53
2.
IR Video Deviation Adjustment (VC-254 board) 5-53
3.
IR Audio Deviation Adjustment (VC-254 board) 5-54
3-6. AUDIO SYSTEM ADJUSTMENTS 5-55
1.
Hi8/Standard8 AFM BPF fo Adjustment (VC-254 board) 5-55
2.
Hi8/Standard8 AFM 1.5 MHz Deviation Adjustment
(VC-254 board) 5-56
3.
Hi8/Standard8 AFM 1.7 MHz Deviation Adjustment
(VC-254 board) 5-56
4.
Digital8 Playback Level Check 5-56
5.
Overall Level Characteristics Check 5-56
6.
Overall Distortion Check 5-56
7.
Overall Noise Level Check 5-57
8.
Overall Separation Check 5-57
5-4. SERVICE MODE 5-58
4-1. ADJUSTMENT REMOTE COMMANDER 5-58
1.
Using the Adjustment Remote Commander 5-58
2.
Precautions Upon Using the Adjustment Remote
Commander 5-58
4-2. DATA PROCESS 5-59
4-3. SERVICE MODE 5-60
1.
Setting the Test Mode 5-60
2.
Emergence Memory Address 5-60
2-1. C Page Emergence Memory Address 5-60
2-2. F Page Emergence Memory Address 5-61
2-3. EMG Code (Emergency Code) 5-61
2-4. MSW Code 5-62
3.
Bit Value Discrimination 5-63
4.
Switch check (1) 5-63
5.
6.
7.
8.
9.
Record of Use check 5-64

Record of Self-diagnosis check 5-65
6.
REPAIR PARTS LIST
6-1. EXPLODED VIEWS 6-1

6-1-1. OVERALL SECTION 6-1
6-1-2. CABINET (L) SECTION-1 6-2
6-1-3. CABINET (L) SECTION-2 6-3
6-1-4. CABINET (R) SECTION (2.5 INCH LCD MODEL)
(TRV230/TRV330) 6-4
6-1-5. CABINET (R) SECTION (3.5 INCH LCD MODEL)
(TRV530) 6-5
6-1-6. LCD SECTION (2.5 INCH LCD MODEL)
(TRV230/TRV330) 6-6
6-1-7. LCD SECTION (3.5 INCH LCD MODEL)(TRV530) 6-7
6-1-8. LENS, EVF SECTION 6-8
6-1-9. CASSETTE COMPARTMENT ASSY, DRUM ASSY 6-9
6-1-10. LS CHASSIS BLOCK ASSEMBLY 6-10
6-1-11. MECHANICAL CHASSIS BLOCK ASSEMBLY-1 6-11
6-1-12. MECHANICAL CHASSIS BLOCK ASSEMBLY-2 6-12
6-2. ELECTRICAL PARTS LIST 6-13
* Optical axis frame and color reproduction frame are
shown on pages 294 and 295.
SERVICE NOTE
1.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power code (J-6082-223-A), the power
is shut off so that the unit cannot operate.
These following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the DC IN terminal. (Use the AC power adaptor.)
Method 2.
Connect the adjustment remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the HOLD switch to the ADJ side.
2.
1
2
3
4
5
6
7
8
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)

Refer to 2-3. to remove the front panel section.
Refer to 2-4. to remove the cabinet (Upper) assembly.
Refer to 2-4. to remove the cabinet (R) assembly.
Refer to 2-9. to remove the memory stick connector assembly. (DCR-TRV330/TRV530)
Refer to 2-10. to remove the battery panel section.
Refer to 2-11. and 2-12. to remove the cabinet (L) section. (Include the CS frame assembly and control switch block (SS-1380).)
Disconnect CN4401 (2P) of VC-254 board.
Add +5V from the DC POWER SUPPLY and unload with a pressing the cassette compertment.
9 Pull the timing belt in the direction of

arrow A with a pincette while pressing
the cassette compartment (take care
not to damage) to adjust the bending
of a tape.
Pincette
A
Timing belt
Press the cassette compartment not

to rise the cassette compartment
0 Let your hold the cassette

compartment and rise the cassette
compartment to take out a cassette.
Timing belt
DC power supply
(+5V)
Adjust the bending
of a tape
Loading
motor
Disconnect CN4401 of
VC-254 board
SELF-DIAGNOSIS FUNCTION
1.
Self-diagnosis Function
2.
When problems occur while the unit is operating, the self-diagnosis

function starts working, and displays on the viewfinder or Display
window what to do. This function consists of two display; selfdiagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
Viewfinder
Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
viewfinder or Display window shows a 4-digit display consisting
of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the repaired by:, block in which the problem
occurred, and detailed code of the problem.
Display window
C : 3 1 : 11
C:31:11
Blinks at 3.2Hz
31
11
Display window
Block
Repaired by:
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
3.
Detailed Code
Refer to page 10 and 11.

Indicates the appropriate
Self-diagnosis Code Table.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Service Mode Display
The service mode display shows up to six self-diagnosis codes shown in the past.
3-1.
Display Method
While pressing the STOP key, set the switch from OFF to VTR or PLAYER, and continue pressing the STOP key for 5 seconds
continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
Viewfinder
Display window
3 C : 3 1 : 11
[3] C : 3 1 : 1 1
Lights up
[3]
Backup No.
C:31:11
Self-diagnosis Codes
Control dial
Order of previous errors
3-2.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
[4] : Occurred fourth time
[2] : Occurred second time [5] : Occurred fifth time
[3] : Occurred third time
[6] : Occurred the last time
3-3.
End of Display
Turning OFF the power supply will end the service mode display.
Note: The self-diagnosis display data will be backed up by the coin-type lithium battery (CF-079/080 board BT101). When
the CF-079/080 board is disconnected, the self-diagnosis display data will be lost by initialization.
4.
Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Detailed
Function
Code
Symptom/State
C
C
C
0
2
2
4
1
2
0
0
0
0
0
0
C
C
C
C
C
C
C
C
C
C
C
3
3
3
3
3
3
3
3
3
3
3
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
3
3
4
4
4
4
4
0
1
2
3
0
1
0
1
2
3
4
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan

operations.
FG fault when starting drum.
PG fault when starting drum.
Correction
Non-standard battery is used.

Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
S reel side tape slacking when unloading.
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum operations.
PG fault during normal drum operations.
Phase fault during normal drum operations.
LOAD direction loading motor timeout.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
S reel side tape slacking when
unloading.
FG fault during normal drum

operations.
PG fault during normal drum
operations.
Phase fault during normal drum
operations.
Use the InfoLITHIUM battery.

Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
10
Repaired by:
Self-diagnosis Code
Block
Detailed
Function
Code
Symptom/State
Difficult to adjust focus

(Cannot initialize focus.)
Zoom operations fault

(Cannot initialize zoom lens.)
Correction
Inspect the lens block focus reset sensor (Pin qd of CN1551 of

VC-254 board) when focusing is performed when the control dial
is rotated in the focus manual mode and the focus motor drive circuit
(IC1553 of VC-254 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin qs of CN1551 of
VC-254 board) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC1553 of VC-254
board) when zooming is not performed.
Handshake correction function does not

work well. (With pitch angular velocity
sensor output stopped.)
Handshake correction function does not
work well. (With yaw angular velocity
sensor output stopped.)
Inspect pitch angular velocity sensor (SE301 of SE-028/029

board) peripheral circuits.
Inspect yaw angular velocity sensor (SE302 of SE-028/029
board) peripheral circuits.
11
SECTION 1
GENERAL
1-1
This section is extracted from
instruction manual.
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
1-21
1-22
1-23
1-24
1-25
1-26
1-27
1-28
1-29
1-30
1-31
1-32
1-33
1-34
1-35
1-36
1-37E
SECTION 2
DISASSEMBLY
The following flow chart shows the disassembly procedure.

2-1. LCD unit, PD-138 board (TRV230/TRV330)
PD-138 board service position
2-2. LCD unit, PD-139 board (TRV530)
PD-139 board service position
2-3. Front panel section, SI-028/029 board
SI-028/029 board service position
2-4. Cabinet (R) section
2-15. Hinge section
2-5. CF-079 board (TRV230/TRV330)
2-6. CF-080 board (TRV530)
CF-079/080 SI-028/029 boards service position
2-7. EVF section, LB-068/070 board
LB-068/070, CF-079/080, SI-028/029 boards

service position
2-8. Lens section, CD-292/315 board
CD-292/315, CF-079/080, SI-028/029 boards

service position
2-9. PC-082 board (TRV330/TRV530)
PC-082, CF-079/080, SI-028/029 boards

service position
2-10. Battery panel section, Battery terminal board
2-11. Control switch block (SS-1380), FU-150/154 board
Mechanism deck service position-1
2-12. Cabinet (L) section, Mechanism deck-1
2-13. VC-254 board
2-14. Mechanism deck-2, MD frame
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)]
(VC-254, FU-150/154, CD-292/315, SI-028/029, PC-082, CF-079/080 boards, Mechanism deck-2)
2-1
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD UNIT, PD-138 BOARD (TRV230/TRV330)

3 Two claws
REMOVING THE BACK LIGHT

2 Remove the indication LCD block assembly,
back light in the direction of the arrow B.
4 P cabinet C (2)
1 Two MI screws
(M2 4) (H)
5 Screw
(M1.7 2.5),
lock ace, p2
6 Claw
3 LCD holder (2)
1 Five claws
7
8
-13
PD oard
B
6 Indication LCD
block assembly
qa Remove the PD-138 board

in the direction of the arrow A.
A
4 Remove
the three
solderings
8 Two tapping screws

(B1.7 6)
0 Two claws
qs P frame (2)
5 Six claws
7 Back light
qf Back light
Cold cathode fluorescent tube,
BL shield sheet (N)
qd Liquid crystal
indicator module
9 P cabinet M (2) assembly

(M1.7 5)
[PD-138 BOARD SERVICE POSITION]

Liquid crystal indicator module
Back light
BL shield sheet (N)
CN5502
DC IN
8
-13
PD oard
B
AC POWER
ADAPTOR
LANC
jack
PD-138 board
Multi CPC jig
(J-6082-311-A)
Indication LCD block assembly
2-2
Adjustment remote
commander (RM-95)
AC IN
2-2. LCD UNIT, PD-139 BOARD (TRV530)

REMOVING THE BACK LIGHT
4 P cabinet C (3) assembly
2 Remove the indication LCD block assembly,

back light in the direction of the arrow B.
1 Two MI screws
(M2 4) (H)
7 Two screws
(M1.7 2.5), p
A
B
5 Screw
(M1.7 2.5), p
3 LCD holder (2)
1 Five claws
6
6 Indication LCD
block assembly
0 Screw (M1.7),
lock ace, p2
9
-13
PD oard
B
4 Remove
the three
solderings
qs Remove the PD-139 board in the

direction of the arrow B.
qa Two claws
5 Six claws
qd P frame (3)
7 Back light
qg Back light
BL shield sheet (N)
qf Liquid crystal
indicator module
3 Six claws
8 Two MI screws
(M2 4) (H)
A
9 P cabinet M (3) assembly

(M1.7 5)
[ PD-139 BOARD SERVICE POSITION]

Liquid crystal indicator module
Back light
BL shield sheet (N)
CN5502
9
-13
PD oard
B
Multi CPC jig

(J-6082-311-A)
PD-139 board
DC IN
AC POWER
ADAPTOR
LANC
jack
Indication LCD block assembly
2-3
Adjustment remote
commander (RM-95)
AC IN
2-3. FRONT PANEL SECTION, SI-028/029 BOARD

Push the eject knob in
the direction of the arrow A,
and open the cassette lid.
A
4 Two MI screws
(M2 4) (H)
REMOVING THE SI-028/029 BOARD

4 Remove the FP-273 board in the
direction of the arrow B.
6 SI-028 board
(TRV230/TRV330),
SI-029 board (TRV530)
3 MI screw
(M2 4) (H)
5 Claw
1 Cushion (SI)
2 Sensor
cushion
6 FP-266 flexible
board (26P)
3 Two tapping
screws
(B2 5)
qf Front panel
assembly
2 MI screw
(M2 4) (H)
7 Front panel section
qs Microphone
(Rch)
5 Tapping screw
(B2 5)
l8
ta
gi
Di
7 Cushion
(MI)
qd Microphone
(Lch)
8 Tapping screw
(B2 5)
9 Claw
qa Microphone retainer
0 Microphone
grille assembly
Microphone retainer (rear view)

Microphone (Lch)
Microphone (Rch)
When removing it, be careful not to damage
the harnesses, etc.
[SI-028/029 BOARD SERVICE POSITION]
Front panel
section
AC POWER
ADAPTOR
DC IN
FP-266 flexible
board (26P)
SI-028 board (TRV230/TRV330),
2-4
AC IN
2-4. CABINET (R) SECTION

1 MI screw
(M2 4) (H)
5 Two MI screws
(M2 4) (H)
2 Three claws
B
A
4 Two MI screws
(M2 4) (H)
3 Cabinet
(upper)
6 MI screw
(M2 4) (H)
A
B
Harness
(VP-076) (20P)

(M1.7 5)
Flexible flat cable

(FFC-001) (45P)
8 Two MI screws
(M2 4) (H)
0 Cabinet (R) block assembly
9 Three MI screws
(M2 4) (H)
2-5. CF-079 BOARD (TRV230/TRV330)
0 Cabinet (R) block

assembly
9 Tripod retainer,
Tripod screw (Y)
2 Control switch block
(SE-1380)
CF
-0
Bo 79
ar
d
REMOVING THE CF-079 BOARD
1 Tapping screw
(B2 5)
7 Cabinet (R) block assembly

3 Two tapping
screws (B2 5)
2 Claw
3 Remove the CF-079 board,
Flexible flat cable (FFC-001)
in the direction of the arrow.
4 Speaker
(2.0CM)
5 Speaker
spacer
6 Speaker
retainer
8 Tapping screw
(B2 5)
5 CF electrostatic
sheet (2)
7 MI screw
(M2 4) (H)
CF
Bo -07
ar 9
d
4 CF electrostatic
sheet
6 Muffle sheet
1 Three tapping screws
(B2 5)
2-5
2-6. CF-080 BOARD (TRV530)

REMOVING THE CF-080 BOARD
Tape (A)
Harness
(VP-076)
7 Cabinet (R) block

assembly
0 Tape (A)
5 CF electrostatic
sheet (4)
qa Cabinet (R) block

assembly
4 CF electrostatic
sheet (3)
CF
Bo -080
ar
d

(SE-1380)
1 Tapping screw
(B2 5)
CF
Bo -08
ar 0
d
3 Two tapping
screws
(B2 5)
3 CF electrostatic
sheet
6 Muffle sheet
7 MI screw
(M2 4) (H)
4 Speaker
(2.0CM)
5 Speaker
spacer
8 Tapping
screw
(B2 5)
9 Tripod retainer,
Tripod screw (Y)

(B2 5)
2 Remove the CF-080 board, Flexible flat cable (FFC-001) in the
direction of the arrow.
6 Speaker
retainer
[CF-079/080, SI-028/029, BOARDS SERVICE POSITION]

2 Claw
CPC-13 jig
(J-6082-443-A)
CN1108
CN1108
1
20
3 CPC lid (BT)

1 MI screw
(M2 4) (H)
AC POWER
ADAPTOR
DC IN
FP-266 flexible
board (26P)
AC IN
Adjustment remote
commander (RM-95)
LANC
jack
Control switch block

(SE-1380)
CF-079 board (TRV230/TRV330),
CF-080 board (TRV530)
- d
F r
C oa
B
Flexible flat cable

(FFC-001) (45P)
Speaker
(2.0CM)
Front panel
section
Cabinet (R) block

assembly
Harness
(VP-076) (20P)
2-6
2-7. EVF SECTION, LB-068/070 BOARD

PRECAUTION WHEN ATTACHING
FP-268 FLEXIBLE BOARD
3 B label
1 FP-268 flexible
board (20P)
4 EVF section
FP-268 flexible board

Flexible
guide
CF
Bo a
2 Three tapping
screws (B2 5)
rd
EVF section
Fix the FP-268 flexible board to both the EVF section,

and flexible guide with the both-sided adhesive tape.
REMOVING THE VF LENS (B) ASSEMBLY
2 Three claws
3 Remove the EVF cabinet (upper)

assembly in the direction of the
arrow B.
qa VF lens (B) assembly

1 Two claws
9 LCD (LCX032AP-J) (16P)
8 LCD cushion
8 FP-268 flexible
board (20P)
6 Prism sheet
(2)
4 Two
claws
5 Illuminator
(1)
qa Remove the EVF cabinet

(lower) assembly in the
direction of the arrow A.
0 LCD cushion
(1)
7 Remove the flexible

guide in the direction
of the arrow D.
7 Prism sheet
(1)
1 Four tapping
screws
(M1.7 5)
3 Two
claws
4 Lamp guide
6 Slide the lower plate of

VF hinge assembly in
the arrow C strongly.
2 LB-068 board (TRV230/TRV330),

LB-070 board (TRV530)
9 Two tapping
screws (M1.7 5)
0 VF hinge assembly
[LB-068/070, CF-079/080, SI-028/029 BOARDS SERVICE POSITION]

2 Claw
CN1108
CN1108
1
CPC-13 jig
(J-6082-443-A)
20
3 CPC lid (BT)

1 MI screw
(M2 4) (H)
AC POWER
ADAPTOR
DC IN
FP-266 flexible
board (26P)
Front panel
section
LANC
jack
AC IN
Adjustment remote
commander (RM-95)
Harness
(VP-076) (20P)
Flexible flat cable
(FFC-001) (45P)
C
Bo Far
d


FP-268 flexible
board (20P)
LB-068 board (TRV230/TRV330),
LB-070 board (TRV530)
VF lens
Cabinet (R) block
assembly
2-7
2-8. LENS SECTION, CD-292/315 BOARD

REMOVING THE IRIS FLEXIBLE ASSEMBLY
(B1.7 3.5), head
3 FP-265 flexible
board (16P)
2 Tape (A)
6 Tapping screw (M1.7 5)

3 Remove the eight
solderings
1 Electrostatic
sheet T
B
1 Two tapping
screws (M1.7 5)
(TRV530)
6 Lens section
9 Iris flexible
assembly
5 Two screws
(M1.7 2.5)
B
4 Stepping
motor Z700
(Zoom)
4 Iris flexible
assembly (24P)
qa
7 CD-292 board (TRV230/TRV330),

CD-315 board (TRV530)
6 CCD block
assembly
5 Stepping
motor F700
(Focus)
7 Tapping screw
(M1.7 5)
2 Two tapping
screws (B1.7 6)
2 Two tapping
screws (M1.7 5)
0 Lens
cushion
1 FP-265 flexible
board (16P)
5 Remove the
solderings
4 Seal rubber (W)
3 Optical filter block
8 Lens device (LSV-700A)
[CD-292/315, CF-079/080, SI-028/029 BOARDS SERVICE POSITION]

2 Claw
CN1108
CPC-13 jig
(J-6082-443-A)
CN1108
1
20
3 CPC lid (BT)

1 MI screw
(M2 4) (H)
AC POWER
ADAPTOR
CD-292 board (TRV230/TRV330),

FP-266 flexible
board (26P)
DC IN
LANC
jack
Front panel
section
AC IN
Adjustment remote
commander (RM-95)
Harness
(VP-076) (20P)
Flexible flat cable
(FFC-001) (45P)
C
Bo Far
d

2-8
Cabinet (R) block

assembly
2-9. PC-082 BOARD (TRV330/TRV530)

6 Three screws
(M1.7 2.5), p
1 FP-274 flexible
board (12P)
4
-25
VCard
Bo
2 Ferrite bead
REMOVING THE FP-274 FLEXIBLE BOARD

2
-08
PCard
o
B
2 MS holder
5 Memory
stick connector
5 FP-271
board (6P)
4 Remove
the two
solderings
7 PC-082 board
3 Two claws
6 FP-274 flexible
board
4 MS holder, Memory
stick connector,
FP-274 flexible board
1Two tapping
screws (B2 5)
3 Remove the eleven

solderings
[PC-082, CF-079/080, SI-028/029 BOARDS SERVICE POSITION]

PC-082 board
Ferrite
bead
Extension cable
(J-6082-352-A)
2
-08
PCard
o
B
MS holder, Memory
stick connector,
FP-274 flexible board (12P)
CN1901
CN1104
AC POWER
ADAPTOR
DC IN
4
-25
VCard
Bo
AC IN
Adjustment remote
commander (RM-95)
LANC
jack
FP-266 flexible
board (26P)
- d
F r
C oa
B
Front panel
section
Harness
(VP-076) (20P)

Flexible flat cable

(FFC-001) (45P)
Cabinet (R) block

assembly

2-9
2-10.BATTERY PANEL SECTION, BATTERY TERMINAL BOARD

3 MI screw
(M2 4) (H)
4 Claw
2 MI screw
(M2 4) (H)
5 Remove the battery panel section

1 Tapping screw
(M1.7 5)
4
-25
VCard
Bo
6 MI screw
(M2 4) (H)
Battery panel
section
7 Strap sheet
metal (lower)
CS frame
assembly
8 Battery terminal
board (6P)

(SS-1380)
2-11.CONTROL SWITCH BLOCK (SS-1380), FU-150/154 BOARD

8 Remove the control switch block
(SS-1380) (12P) in the direction
of the arrow B.
3 Tapping screw
(M1.7 5)
4 Screw (M1.7 2.5), p
7 Two dowels
5 Two dowels
5
-2
VCard
Bo
C
1 Two screws
(M1.7 2.5), p
Remove the control switch block (SS-1380) in the

direction of the arrow C.
2 FU-150 board (TRV230/TRV330),

FU-154 board (TRV530)
Push the eject knob in

the direction of the arrow A,
and open the cassette lid.
A
2-10
CS frame
assembly
2-12.CABINET (L) SECTION, MECHANISM DECK-1
REMOVING THE CS FRAME ASSEMBLY

2 Two MI screws
(M2 4) (H)
4 Four dowels
3 Screw
(M1.7 2.5), p
5 Cabinet (L) section,

CS frame assembly
5 Cabinet (L)
assembly
1 MI screw
(M2 4) (H)
4
-25
VCard
Bo
2 Screw
(M1.7 2.5), p
4 Grip
belt (ES)
3 Two MI screws
(M2 4) (H)
1 Two screws
(M1.7 2.5), p
6 CS frame
assembly
[MECHANISM DECK SERVICE POSITION-1]

Note: Use the parts only which can be removed easily from outside of the mechanism deck.
Operate the VTR using the adjustment remote commander. (with the HOLD switch set in the OFF position)
How to raise the cassette compartment manually

Remove the hook in the direction of the arrow A to raise the cassette compartment
in the direction of the arrow B.
A

Cabinet (R) block

assembly

(SS-1380) (12P)
Harness
(VP-076)
(20P)
FP-266 flexible
board (26P)
CF
Bo
ar
Flexible flat cable

(FFC-001) (45P)
Battery panel
section
Mechanism deck
Adjustment remote
commander (RM-95)
Front panel
section
AC IN
AC POWER
ADAPTOR
DC IN
CN1120
LANC jack
CN1117
Battery terminal
board (6P)
CN1104
(TRV330/TRV530)
P
Bo Car 082
d
PC-082 board
CN1108
FU-150 board (TRV230/TRV330),
2-11
CPC-13 jig
(J-6082-443-A)
2-13.VC-254 BOARD
qa Remove the VC-254 board
in the direction of the arrow H.
1 Remove the flexible boards
E
E
D
AB C
6 Screw
(M1.7 2.5), p
CD
3 VC sheet
B
A
4
-25 H
VCard
Bo
2 FP-264 flexible
board (15, 20P)
(TRV330/TRV530)
0 Two screws
(M1.7 2.5), p
4 Two screws
(M1.7 2.5), p
9 FU-271
board
7 FP-272 board
5 FP-270 board
8 Screw
(M1.7 2.5), p
2-14.MECHANISM DECK-2, MD FRAME

8 External connector (hot shoe)
(15P Terminal : TRV330/TRV530)
(8P Terminal : TRV230)
1Turn over VC-254 board

in the direction of the arrow.
V
B Co 25
a 4
rd
6 FP-264 flexible board

(15, 20P)
5 MD frame
4 Mechanism
deck
3 Three dowels
2 Three screws
(M1.7 2.5), p
7 Two screws
(M1.7 2.5), p
2-12
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)]
(VC-254, FU-150/154, CD-292/315, SI-028/029, PC-082, CF-079/080 BOARDS MECHANISM DECK-2)
Note: Operate the VTR using the adjustment remote commander (with the HOLD switch set in the OFF position)
Battery panel
section
FU-150 board (TRV230/TRV330),

(SS-1380) (12P)
AC POWER
ADAPTOR
AC IN
DC IN
Battery terminal
board (6P)
Mechanism deck
CPC-13 jig
(J-6082-443-A)
CN1108
CD-292 board (TRV230/TRV330),
FP-265 flexible
board (16P)
V
B Co 2
a 5
rd 4
FP-272 board
Lens section
(TRV330/TRV530)
Extension cable
(J-6082-352-A) PC-082 board
VC-254
board
Iris flexible
assembly (24P)
LANC
jack
2
-08
PCard
Bo
FP-266 flexible
board (26P)
FP-270 board
Adjustment remote
commander (RM-95)
Harness
(VP-076) (20P)
Front panel
section

C
Bo Far
d

Flexible flat cable
(FFC-001) (45P)
2-13
Cabinet (R) block

assembly
2-15.HINGE SECTION
[TRV230/TRV330 MODEL]
9 Four tapping screws
(B2 5)
0 For removing the LCD unit

(See page 2-2)
4 Two claws
8 Harness
(VP-076) (6P)
5 Hinge cover (140)

assembly
7 FP-282
board (6P)
REMOVING THE HINGE ASSEMBLY
CF
Bo -079
ar
d

(SE-1380)
6 Tapping screw
(B2 5)
1 Harness
(VP-076)
(6, 20P)
3 Three tapping
screws (B2 5)
1 Tapping screw
(B2 5)
Remove the Harness (VP-076) (6, 20P)

2 FP-283
board (6P)
Then bend the harness so that it is laid

along with the connector.
4 Two claws
7 Hinge
assembly
5 Hinge cover (C)
[TRV530 MODEL]
9 For removing the LCD unit
(See page 2-3)
8 Four tapping
screws (B2 5)
8 Harness (VP-076)
6 Hinge
cover (M)
1 Two screws
(M1.7 2.5), p
3 Remove the Hinge cover (148)

assembly in the direction
of the arrow B.
3 Four claws
2 FP-283 board
1 Two tapping
screws (B2 5)
B
7 Harness
(VP-076) (6P)
CF
Bo -080
ar
d
2 Claw
6 Tape (A)
5 FP-282
board (6P)
4 Tapping screw
(B2 5)
Tape (A)
Harness
(VP-076)
2-14
2 Hinge
assembly
1 Harness
(VP-076)
2-16.CIRCUIT BOARDS LOCATION

LB-068 (TRV230/TRV330)
LB-070 (TRV530)
(EVF BACK LIGHT)
CF-079 (TRV230/TRV330)
CF-080 (TRV530)
CD-292 (TRV230/TRV330)
(USER FUNCTION, EVF DRIVE)
CD-315 (TRV530)
(CCD IMAGER)
PD-138 (TRV230/TRV330)
PD-139 (TRV530)
RGB DRIVE, TIMING GENERATOR,
LCD DRIVE, BACK LIGHT DRIVE
PC-082 (TRV330/TRV530)
DIGITAL STILL CONTROL,
DS STILL PROCESS
FU-150 (TRV230/TRV330)
FU-154 (TRV530)
(POWER SUPPLY)
FP-273
(MIC, HEADPHONES)
FP-272
(LANC, DV IN/OUT)
FP-270
(S VIDEO, AUDIO/VIDEO)
FP-271 (TRV330/TRV530)
(USB)
SI-028 (TRV230/TRV330)
SI-029 (TRV530)
STEADY SHOT, REMOTE COMMANDER RECEIVER,
LASER LINK
FP-283
FP-275
(PANEL REVERSE)
(SWITCH)
VC-254
CAMERA/Hi8/STD8/PB PROCESS, DV SIGNAL,
PB RF AMP, VIDEO IN/OUT, AD CONVERTER,
MODE/CAMERA/MECHA CONTROL, LASER LINK,
DRUM CAPSTAN DRIVE, AUDIO PROCESS, MIC,
DC/DC CONVERTER
FP-282
(FOCUS)
2-15
2-17.FLEXIBLE BOARDS LOCATION

The flexible boards contained in the mechanism deck are not shown.
FP-268
FP-264
FP-274
(TRV330/TRV530)
FP-265
FP-266
CONTROL SWITCH BLOCK

(SS-1380)

(SE-1380)
IRIS FLEXIBLE
ASSEMBLY
FFC-001
2-16E
SECTION 3
BLOCK DIAGRAMS
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
3-1. OVERALL BLOCK DIAGRAM (1/5)
CN1108(1/4)
FOR ADJUSTMENTS
2
CD-292 BOARD(TRV230/TRV330)
CD-315 BOARD(TRV530)
VC-254 BOARD(1/4)
AFC F0
(4-17)
LENS ASSY
(4-16)
(4-10)
IRIS
IC501
ZOOM MOTOR
M904
ZOOM
RESET
SENSOR
NIGHT
SHOT
IRIS
METER
M905
FOCUS
RESET
SENSOR
CN1501
7
FOCUS MOTOR
CCD OUT
14
14
16
V1-V4,RG,H1,H2
18
30
(4-16)
CCD
IMAGER
1
2
15
16
IC1501
31
TIMING
GENERATOR
18
CN501
CN1551
12 13
10
ZOOM
A,B,XA,XB
ZM RST
FC RST
LENS FILTER ON SW
17 19
21
FOCUS
A,B,XA,XB
2
IC1553
IC1552
FOCUS
MOTOR
DRIVE
9 12
EN1
DIR1A
DIR1B
X1501
27MHz
21 23
(4-20)
ZOOM
MOTOR
DRIVE
13 16
IRIS DRIVE(-)
HALL
AMP
IRIS
DRIVE
(4-20)
7
EN0
DIR0A
DIR0B
XCS KINUTA
(IC4902)
10
HALL
AD
AD1-AD10
16
34 36
46 47 48
ADCK
FP-273
(HEADPHONES)
L,R
J302
MIC
(PLUG IN
POWER)
L,R
PB C RF
AFM FSC
SE302
YAW SENSOR
9
7
13
14
LIA2
25
24
97
38
37
39
VC SO,VC SI,XVC SCK
23
12
PITCH/YAW
SENSOR
AMP
(4-82)
18
REMOTE
COMMANDER
RECEIVER
19
20
8
9
13
12
EXT MIC L,R
SIRCS SIG
INT MIC L,R
10
CN1115
4
6
4
IC3901
IR
TRANSMITTER
46
48
42
18
7
IR L,R
IR V
SIRCS PWM
IR FSC
(IC3301)
51
ATF IN
TO
OVERALL
BLOCK(4/5)
49
Y
C
XCS AU
(IC4501)
23
146
HD,VD,OE
144
142
IC5701
4
5
L,R
3
2
7
8
L,R
15
16
XCS KINUTA
(IC4902)
77
DOP
(IC3201)
(ALIGN)
52
VIDEO
A/D
CONV.
49
Y0-Y7
C0-C7
C0-C7
AFCK
SPCK
(IC1501)
XCS ALIGN
(IC803)
DATA TO SFD
DATA FROM SFD
SFD BCK
8
9
12
TO
OVERALL
BLOCK(3/5)
(SEE PAGE
3-5)
RF AGC OUT (PB Y RF)
HI8/STD8
PB AUDIO
PROCESS
14
26
AFM FSC(IC2201)
PB C RF
PB RF
PB RF (PB AFM RF)

XCS TAKO
(IC4501)
11
39
48
18
14
10
36
(4-28)
IC3701
42
22
24
VIDEO
IN/OUT
AGC
ACC
34
46
7
44
5
Y
C
CAIN Y
CAIN C
SP+,-
KINUTA Y
KINUTA C
SIRCS PWM
SIRCS SIG
SIRCS SIG
(TRV530)
16
3-1
(TRV330/TRV530)
HD,VD,OE
HD,VD,OE
HI SO,HI SI,XHI SCK
13
15
RXD
TXD
(TRV230)
Y0-Y7
31
68
66 64 63
AUDIO
A/D CONV.
D/A CONV.
(SEE PAGE
3-3)
HD,VD,OE
90
CN1104
38
37
36
34
55
56
SP+,- 49
51
C0-C7
TO
OVERALL
BLOCK
(2/5)
(PC-082)
42
65
IC5702
AUDIO
IN/OUT
64
3
57
58
98
10
RXD,TXD
89
CK CONT1,2
(IC4902)
59
(4-44)
IR V
STB ON
(4-43)
(TAKO)
CN1101
SHOE MIC L
C0-C3
IC3603
(4-30)
V
V
10
40 42
44 46
48 50
52 54
39
37
35
119
Y0-Y7
(SEE PAGE 3-7)
Y
C
Y
C
8
6
63
2
13
22 MIC L,R
14
(4-38)
CN1116
INTELLIGENT
ACCESSORY
SHOE(1/2)
IC5801
36
48
17
J102
AUDIO/VIDEO
HP L,R 52
54
35
1
22
J101
S VIDEO
(4-45)
16
CN304
(FLEXIBLE)
(SEE PAGE 4-27)
YAW AD
MIC
AMP
SHOE MIC L
11
33
3
122
21
25
29
33
AFCK
MECHA HD
MECHA VD
93 MECHA FLD
94 TBC VD
89
158
Y
4
C
213
20 22
D307,308
(LASER LINK)
IC301
FP-270
153
161
162
VSP SO,XVSP SCK
7
8
19
18
14
15
R
CN303
FC RST,ZM RST
MECHA HD,VD,FLD
TBC VD
SI-029 BOARD
CN302
148
(TRV230/TRV330)
EN0,EN1
DIR0A,B
DIR1A,B
VSP SO,VSP SI,XVSP SCK
PITCH AD
Y0-Y7
SPCK
95
RF AGC OUT
MF A,B
PITCH AD,YAW AD
STB ON
(4-36)
IC2001
21
19
23
27
31
139
101
100
169
170
HD,VD
SI-028 BOARD
MIC902
MIC
R
2
3
45
Y
44
45
VC SO,VC SI,XVC SCK
(TRV530)
MIC901
MIC
L
SE301
LIA1
PITCH SENSOR
(FLEXIBLE)
(SEE PAGE
4-81)
J301
185
81
198
79
SPCK
VCK
IRIS PWM
MF A,B
HI8/STD8
PB Y/C
PROCESS
ATF
SPCK
CN301
FOCUS
RING
AFCK(IC3603)
112
23
XCS CH,CH SO,XCH SCK
1
5
FOCUS/
ZOOM
MOTOR
CONTROL
187
11
PB
IRIS PWM,HALL AD
FC RST,ZM RST
LENS FILTER SW ON
MF PHOTO
SENSOR
CAMERA
SIGNAL
PROCESS
196
A/D
CONV.
LINE
47
IC2201
66
67
CAM
S/H
AGC
5
46
47
CK CONT1,2
(IC4902)
CLPOB
PBLK
XSHP
20
XSHD
VCO
ADCK
9
SPCK
11
VCK
12
19
IRIS
HALL(-)
53
IC1502
SPCK(IC1501)
3-2
TO
OVERALL
BLOCK(5/5)
(SEE PAGE
3-10)
(TRV530)
PC-082 BOARD
(4-64)
CN1901
SPCK
AFCK
(SEE PAGE
3-2)
HD,VD,OE
RXD
TXD
3
7
11
15
32
36
42
(L-PLATZ)
35
DS STILL
PROCESS
25
33
30
18
29
28
27
10
3
4
8
12
16 18
20 22
24 26
28 30
56 58
60 62
100
15
14
13
92
91
89
90
5
9
13
17
34
38
86
6
10
14
85
84
83
Y0-Y7
C0-C3
HD,VD,OE
TO
OVERALL
BLOCK
(3/5)
(VC-254)
Y0-Y7
(TRV230/TRV330)
VR,VG,VB
(SEE PAGE
3-5)
C4-C7
HD OUT
PANEL COM
PD-138 BOARD(1/2)
PANEL R
PANEL G
PANEL B
HD,VD,OE
48
47
46
18
17
16
IC5501
RGB
DRIVE
41
165
164
163
114
102
140
121
157
158
DATA FROM SFD
85
86
73
XCS LCD
160
53
75
59
63

XCS HONEY
19
TO
OVERALL
BLOCK
(3/5)
(VC-254)
TO
OVERALL
BLOCK
(3/5)
(VC-254)
(SEE PAGE
3-5)
(SEE PAGE
3-5)
(4-61)
A1-A11,A13
HI SO,XHI SCK
PANEL XHD
PANEL XVD
12
12
49
1
16
48
8
25
A0-A19
7
A1-A19
IC1160
(4-59)
28 45
IC1159
40
39
(4-90)
44
IC5502
35
46
45
42
TIMING
GENERATOR
14
15
1
48
(4-90)
19
20
21
VCOM
COM
DA
VGLAC
24
175
181
79
53
(4-91)
BL CONT
161
X1152
25.8048MHz
HI SO,HI SI
68
66
64
X1151
48MHz
145
HI SO,HI SI,XHI SCK
XHI SCK
1
67
12
13
4
5
IC1157
USB
I/F
XCS DS
(SEE PAGE 4-62)
TO
OVERALL
BLOCK
(5/5)
(VC-254)
(SEE PAGE
3-10)
FP-271
(4-62)
148
IC5601
XTAL
OSC
(FLEXIBLE)
CN1152
11
10
2
3
194
193
192
134
(4-59)
HD OUT
PSIG
D+
D-
3
2
CN201
DIGITAL I/O
(USB)
48
47
46
18
17
16
IC5501
RGB
DRIVE
41
XCS LCD
TO
OVERALL
BLOCK
(3/5)
(VC-254)
(SEE PAGE
3-5)
HI SO,XHI SCK
PANEL XHD
PANEL XVD
27
40
39
12
20
VR,VG,VB
22
24
(4-95)
35
44
IC5502
13
11
46
45
42
TIMING
GENERATOR
14
15
1
48
(4-95)
PSIG
VP
DA
8
6
10
MS DIO
MS BS
MS SCLK
(4-97)
MEMORY
STICK
BL CONT
19
24
22
CN5501
CURRENT
DET
CN5502
FOR
ADJUSTMENTS
LCD901
3 INCH
LCD UNIT
T5601
Q5602
ND901
BACKLIGHT
BL HIGH
10
INVERTER
(4-97)
IC5602
BL LOW
CN5604
5
BL DET
IC5601
2
7
6
PANEL 2.8V
(SEE PAGE 4-61)
3-4
BL REG
BACK
LIGHT
DRIVE
1
CN5701
6
2
7
8
12
13
15
Q5601
8
6
5
3
1
4
5
3
(FLEXIBLE)
3-3
CN5604
PANEL 2.8V
FP-274
16
CN1153
4
IC5602
BL LOW
HD OUT
IC1151
(4-91)
(TRV530)
IC1152 (4-59)
160
4
5
PD-139 BOARD(1/2)
177
DIGITAL
STILL
CONTROL
BL REG
BACK
LIGHT
DRIVE
BL DET
4MBIT
FLASH
MEMORY
(4-59)
(KATHMANDU)
169
SYSCLK
10
11
(4-62)
178
171
4
BL HIGH
INVERTER
IC1154
PANEL R
PANEL G
PANEL B
172
T5601
Q5602
ND901
BACKLIGHT
CN5701
35
IC1155
2.5 INCH
LCD UNIT
VR,VG,VB
57
LCD901
18
CN5501
(4-59)
CN5502
FOR
ADJUSTMENTS
10
12
12
Q5601
8
4
5
3
1
HD OUT
16MBIT
SDRAM
2
39
20
VR,VG,VB
22
24
27
13
11
IC1153
32
ADAI2
ADAO2
SFD BCK
D0-D15
C0-C7
IC1901
TXD
Y0-Y7
19 21
23 25
27 29
31 33
40 42
44 46
48 50
52 54
39
37
35
RXD
TO
OVERALL
BLOCK
(1/5)
(VC-254)
CN1901
11
16
46
45
CURRENT
DET
CN202
VC-254 BOARD(2/4)
(4-21)
IC3301
Y0-Y7
(CAIN)
Y0-Y7
199
203
207
213
C0-C3
1
5
11 13
15 17
32 34
C0-C3
36 38
4
HD, VD, OE
12
16 18
TO
OVERALL
BLOCK(2/5)
(PC-082)
(SEE PAGE
3-3)
20 22
Y0-Y7
28 30
6
HD, VD, OE
10
14
ADAO2
SFD BCK
85
202
206
212
216
16
18
22
24
CHARACTER
GENERATOR
(4-23)
1
(LIP)
DV INTERFACE
29
18
17
16
14
HD
VD
FP-272(1/2)
MC BUS
37
(FLEXIBLE)
VREF
RF MON
(SEE PAGE 4-24)
REC CK
REC DT
40
42
AD DT
6
AD DT
6
(4-25)
15
20
PB CK
ATF ERR
PB CK
42
IC3101
PB Y OUT
(TRF)
COL3
DV PB RF
25
MC BUS
22 24
EVEN
FILTER
SW
29
Q3117
Q3111,3116
FLYING
ERASE
OSC
EVEN
11
(SEE PAGE 4-26)
35
4
31
IC3102
(4-25)
XFE ON
159
DRUM 8PB
XCS TRF
(IC4501)
VSP SO, SI, SCK

161
75
73
71
Y0-Y7
SFD BCK
FLYING
ERASE
5
4
7
8
ODD
Q3107
Q3109
Q3119,3120
27
179
105
106
135
134
127
VC RF SWP
DV RF SWP
XCS SFD (IC4501)

XCS VFD (IC4501)
163
162
ADAI2
ADAO2
6
7
2
1
REC/PB
AMP
EQ
A/D CONV.
PLL
13
170
195
194
191
190
DRUM
CN3101
(TRW)
COL0
CN1108(2/4)
FOR
ADJUSTMENTS
ODD
IC3103
REC CK
REC DT
88
184
183
16
5
PB RF (IC3201 14 )
(4-26)
81
79
20
19
1
4
(TRV230)
C0-C7
47
79
TPA+,TPB+,-
83
IC3302
42
TRCK
LCK
34
73
(TRV330/TRV530)
IC3303
99
97
196
48
AFCK (IC2603)
SPCK (IC1505)
86
45
L BUS
152
PRRV,TRRV,TRRT
153
156
DATA TO SFD
133
DATA FROM SFD
132
SFD BCK
127
182
IR FCS
ADAI2
CN1114
(4-23)
142
151
C4-C7
60 62
HD, VD, OE
139
51
141
56 58
C4-C7
X3301
24.576MHz
145
3
7
200
204
208
214
Y0-Y7
24 26
DV SIGNAL
PROCESS
17
21
23
HD,VD,OE
201
205
211
215
DV IN/OUT
138
ATF ERR
ERRV,TRRV,TRRT
PANEL G
PANEL R
DRP SO,XDRP SCK
PANEL B
TO
OVERALL BLOCK
(4/5)
PANEL XHD,XVD
MC BUS
(SEE PAGE 3-7)
HD,VD,OE
55
59
67
BW Y
DATA TO SFD
VC SO,VC SI,XVC SCK
DATA FROM SFD

SFD BCK
TO
OVERALL
BLOCK(1/5)
RF ENV DET
(4-31)
(SEE PAGE 3-2)
EVF VR
EVF VG
ECF VB
IC3201
RF AGC OUT(PB Y RF)
PB C RF
HI8/STD8
PB RF
AMP
18
DV PB RF
VCO
11
PB RF
PB RF(PB AFM RF)
14
XCS OSD
OSD SO
XOSD SCK
CAIN Y
CAIN C
(4-31)
SP+,-
HI SO, XHI SCK
IC3202
(TRV330/TRV530)
CN1104
TO
OVERALL
BLOCK(2/5)
(PC-082)
53
75
59
63
(SEE PAGE
3-3)
DOP
(IC2201)
RF ENV
DET
29
30
28
31
TO
OVERALL
BLOCK
(5/5)
(SEE PAGE 3-10)

4
BL CONT
9
12
10
11
BW Y
39
CN1108(3/4)
FOR
ADJUSTMENTS
17
16
18
15
LCD903
TO
OVERALL
BLOCK(2/5)
(PD-138/139)
IC201
48
47
46
RGB
DRIVE
XCS HONEY
(IC4501)
XCS EVF
(IC4803)
(4-37)
ADJUSTMENT
VOLTAGE
D/A CONV.
(EVR)
XCS LCD
(IC4803)
27
28
15
VC SO,VC SI,XVC SCK

DA STB(IC4902)
HI SO,XHI SCK
PANEL XHD
PANEL XVD
40
39
(4-77)
44
IC202
35
11
(SEE PAGE
3-4)
33
34
13
12
46
45
42
TIMING
GENERATOR
37
36
9
10
1
48
(4-77)
HD OUT
HI SO, XHI SCK
SP+,-
14
15
4
9
8
10
12
13
11
18
CN702
14
15
13
B/W
LCD UNIT
12
11
PANEL XHD,XVD
CN1117
35
LED DA
14
11
10
24
18
IC701
17
CN201
1
SP901
SPEAKER
2
CN101
BL CONT
CN1120
16
3-5
(4-85)
LED
DRIVE
34
35
CN102
3
12
13
11
CN701
20
VR,VG,VB
22
24
41
VSP SO, VSP SI, XVSP SCK
IC2291
18
17
16
12
LB-068 BOARD(TRV230/TRV330)
LB-070 BOARD(TRV530)
CF-079 BOARD(1/2)(TRV230/TRV330)
CF-080 BOARD(1/2)(TRV530)
3-6
D701
(BACK LIGHT)

VC-254 BOARD(3/4)
M2000 MECHA DECK
(4-42)
(SEE PAGE 4-52)
(4-39)
78
79
80
DRP SO,DRP SI,XDRP SCK
74
75
76
IC4501
DIGITAL8
MECHA
CONTROL
SIGNAL
PROCESS
CONTROL
(4-42)
68
69
DRUM PWM
DRUM PWM
CAP PWM
CAP PWM
IC4401
28
25
(3/3)
LPF
29
27
DRUM ERROR
CAP ERROR
IC1301
15
11
(1/2)
PWM
DRIVE
58
64
Q1306
SWITCHING
ATF ERR
DRUM FG
37
DRUM PG
TO
OVERALL
BLOCK(3/5)
(SEE PAGE
3-6)
115
110
109
96
95
XCS VFD (IC3301)

XCS SFD (IC3301)
XCS TAKO (IC3701)
XCS EEP
(4-40)
39
40
41
88
IC4502
EEPROM
17
38
18
XCS AU (IC5701)
XCS TRF (IC3101)
21
23
VREF (IC3301)
112
DV RF SWP
XFE ON
DRUM 8 PB
RF ENV DET
49
50
54
53
XCS MECHA (IC4803)
72
114
113
HI SO,HI SI,XHI SCX
81
82
83
1
44
VC RF SWP
55
FG AMP
17
DRUM FG
22
PG AMP
20
DRUM PG
IC4402
CAP VS
DEW AD
CAP FG
24
IC4902
CAMERA
CONTROL
HI8/STD8
MECHA
CONTROL
114
39
4
VC SO,VC SI,XVC SCX
IC4901
EEPROM
1
XCS KINUTA (IC2201)

DA STRB (IC2291)
(4-35)
XCS EEPROM
TO
OVERALL
BLOCK(1/5)
MECHA FLD
MECHA HD
MECHA VD
TBC VD
78
79
80
19
21
27
69
68
S REEL FG
47
83
82
81
XCS CH,CH SO,XCH SCK
IRIS PWM
STB ON
CK CONT 1,2 (IC2201)
104
110
HI SO,HI SI,XHI SCX
74
75
76
XCS VC (IC4803)
78
TO
OVERALL
BLOCK(5/5)
(SEE PAGE
3-9)
CAP PWM
70
106
87
HI SO,HI SI,XHI SCK
TAPE END
DETECT
46
44
TAPE TOP
DETECT
45
T REEL FG
41
T REEL AFG
40
T REEL
FG AMP
38
39
S REEL FG
33
S REEL AFG
34
S REEL
FG AMP
36
35
TAPE LED ON
MODE SW A-C
CAPSTAN FG
22
DEW SENSOR
21
S901
MODE SWITCH
LM(+),LM(-)
LOAD
UNLOAD
TAPE END(C)
TAPE TOP(C)
14
Q001
41
T REEL(+),(-)
7
6
T REEL
SENSOR
H001
S REEL(+),(-)
9
10
S REEL
SENSOR
H002
Q4401
LED DRIVE
13
96
95
38
23
24
43
88
89
84
97
98
VC RF SWP (IC4902 47 )
T REEL AFG
S REEL AFG
TAPE LED ON
ME SW
HI8 MP SW
ZM RST
FC RST
LENS FILTER SW ON
MF B
MF A
HALL AD
PITCH AD
YAW AD
ZOOM VR AD
16
3-8
TAPE END
SENSOR
TAPE TOP
SENSOR
DV RF SWP (IC4501 62 )
TAPE TOP
D001
TAPE
LED
15
CAP FG
TAPE END
M
Q002
S001
3
4
2
1
CN4404
42
M903
LOADING MOTOR
REC PROOF
ME SW
HI8 MP SW
XCC DOWN
XCC DOWN
3-7
LOADING
MOTOR
DRIVE
53
51
47
DRUM PWM
CAP FG
40
PWM
STB ON
18
16
CN4401
(2/3)
55
56
REC PROOF
115
109
31
HALL AD
FC RST
ZM RST
LENS FILTER SW ON
MF A,B
PITCH AD
YAW AD
FG1,2
IC4401
LOAD
UNLOAD
TAPE LED ON
116
117
32
33
HU,HV,HW
2
(4-42)
T REEL FG
DRUM FG
DRUM PG
35
36
37
19
TAPE TOP
111
112
113
118
(SEE PAGE
3-2)
22
23
M902
CAPSTAN MOTOR
9
7
HU1,2
HV1,2
HW1,2
MODE SW A-C
TAPE TOP
LINE OUT V (IC3301)
FG AMP
TAPE END
VC SO,VC SI,XVC SCX
16
CN4403
14
U,V,W
21
(4-35)
X4901
20MHz
CAPSTAN
MOTOR
DRIVE
5
7
9
MODE SW A-C
LOAD
UNLOAD
(4-42)
TAPE END
10
16
DRUM FG
DRUM PG
CAP FG
U, V, W
DEW AD
62
59
111
99
VC SO,VC SI,XVC SCX
61
59
57
DRUM
MOTOR
DRIVE
(4-49)
116
117
IC4401
(1/3)
26
106
107
108
SWITCHING
Q1305
MC BUS
FRRV,TRRT,TRRV
M901
DRUM MOTOR
CN4402
DRUM VS
15
13
8
REC PROOF
ME/MP
HI8 MP
C.C. LOCK
S002
CN1108(4/4)
FOR
ADJUSTMENTS

CF-079 BOARD(2/2)
VC-254 BOARD(4/4)
(4-34)
IC4803
LANC SIG
CF-080 BOARD(2/2)
HI CONTROL
SHOE/PRT UNREG
CN1113
(TRV530)
CONTROL
SWITCH
BLOCK
(SE-1380)
SEL/PUSH
EXEC
DIAL
3
4
MENU EXEC
25
23
26
27
28
EXPOSURE SW
CN107
FP-282
CN106
(FLEXIBLE)
(SEE PAGE 4-76)
15
14
(SEE PAGE 4-76)
FOCUS
SW
31
32
S102-108
67 DIAL A
68 DIAL B
FOCUS AUTO
FUNCTION
SW
21
23
20
19
18
93 KEY AD0
KEY AD0-KEY AD4
97 KEY AD4
KEY AD1
X4801
20MHz
(4-33)
CN105
PANEL
OPEN/CLOSE
SW
IC4801
RESET
FP-275
KEY AD0
KEY AD1
VTR
FUNCTION
SW
(FLEXIBLE)
(SEE PAGE 4-76)
SNIGHT SW
37
BT101
LITHIUM
BATTERY
3
7
VTR UNREG
VDD SWITCH
BATT UNREG
20
17
18
(TRV330/TRV530)
CN1104
XCS MECHA 80
XCS VC 3
XCS ALIGN 58
XCS LCD 27
XCS EVF ?
XCS MECHA (IC4501)

XCS VC (IC4902)
XCS ALIGN (IC3603)
XCS LCD (IC5501, 5502)
67
68
66
64
XCS DS
38 XRESET
42
51
77
87
VDD
TO
OVERALL BLOCK(2/5)
(PC-082)
HI SO, HI SI, XHI SCK
(SEE PAGE 3-3)
XCS EVF (IC201,202)

XCC DOWN
XCC DOWN 18
TO
OVERALL
BLOCK(4/5)
41 20MHz IN
52 32kHz IN
53 32kHz OUT
INTELLIGENT
ACCESSORY
SHOE(2/2)
(SEE PAGE
3-7)
ZOOM VR AD
SIRCS SIG
HI SO 33
HI SI 34
HI SCK 35
SIRCS SIG
TO
OVERALL
BLOCK(1/5)
(SEE PAGE
3-2)
SIRCS, PWM
XCS OSD
OSD SO
XOSD SCK
TO
OVERALL
BLOCK(3/5)
CN104
IC5701
CN5705
LCD902
1
11
20
30
30
INDICATOR
DRIVE
1
2
10
4
CN103
FP-283
(FLEXIBLE)
(SEE PAGE
PD-138 4-89,
PD-139 4-95)
16
XOSD SCK
OSD SO
LCD COM/XDATA
XCS LCD DRIVER
41
38
KEY AD5
CONTROL
SWITCH
BLOCK
(SS-1380)
(SEE PAGE 4-101)
7
8
START/STOP
SW
POWER
SW
1
4
3
KEY AD1
XPHOTO FREEZ
IC4802
11
LANC
I/O
(4-33)
46
45
XOSD SCK
OSD SO
10
12
1
2
LANC IN
LANC OUT
48
79
IB SI
IB SO
SIRCS ENV 59
MELODY 36
I/F
11
12
19 XPHOTO FREEZ
16 XS/S SW
8
7
10
8
7
10
14 XVTR MODE SW
15 XCAM MODE SW
20 XPHOTO STBY SW

BL CONT
BATT/EXT SW
FAST CHARGE
INIT CHARGE ON
SHOE ON
66
50
25
81
BL REG
PC 1.9V
D 1.9V
D 2.8V
AU 2.8V
A 2.8V
A 4.75V
AU 4.75V
RP 4.75V
MT 5V
EVF BL 4.75V
EP 2.8V
EP 13.3V
PANEL 4.75V
PANEL -15.3V
CAM -7.5V
(2/2)
IC1301
FU-150 BOARD(2/2)
DC/DC
CONV.
(TRV230/TRV330)
FU-154 BOARD(2/2)
(TRV530)
(SEE PAGE 4-101)
CAM 15V
D 1.5V
RP 6.0V
17
17
20
20
21
21
24
24
25
25
Q403
28
28
CHARGE
SW
15
16
15
16
3
5
2
14
3
5
2
14
4
30
32
34
4
30
32
34
36
38
40
36
38
40
(4-49)
EJECT SW
ZOOM VR
12
11
XEJECT SW
ZOOM VR AD
CN402
17 XEJECT SW
CN403
BATT UNREG
FAST CHARGE
BATT/EXT SW
BATT SIG
BATT SIG
CN1113
INIT CHARGE ON
FU-150 BOARD(1/2) FU-154 BOARD(1/2)

(TRV230/TRV330)
SHOE ON
(TRV530)
SHOE/PRT UNREG
INTELLIGENT
ACCESSORY
SHOE
(SEE PAGE 4-101)

LANC SIG
J201
LANC
8
CN1114
(SEE PAGE 4-24)
CN1113
3-9
CN401
Q402
3-10
4
3
2
6
5
1
Q407
(TRV230)
Q408
PRT HEAD UNREG
FP-272(FLEXIBLE)(2/2)
16
(SEE PAGE
3-8)
MOD
CAM DD ON 28
VTR DD ON 29
Q4804
11
12
XS/S SW
XVTR MODE SW
XCAM MODE SW
XPHOTO STBY SW
LCD COM/XDATA
XCS LCD DRIVER
98 KEY AD5
19
CN1120
PD-138 BOARD(2/2)(TRV230/TRV330)
PD-139 BOARD(2/2)(TRV530)
PHOTO
SW
24
60
44 XCS OSD
CN102
19
CN5701
CN5703
Q4802, 4813
CN5704
(PD-138 4-92,
PD-139 4-98)
S601
PANEL
REVERSE
SW
19
40 20MHz OUT
BATT LI 3V
5
3
6
S101
RESET
CHARACTER
DISPLAY
X4802
32.768kHz
16
PRT HEAD UNREG
XCS DS 79
CN1117
DIAL A
DIAL B
CN1101
(TRV230/TRV330)
(TRV330/TRV530)
DC IN
+
S
BT901
BATTERY
TERMINAL
3-6. POWER BLOCK DIAGRAM (1/3)

(SEE PAGE 4-101)
FU-150 BOARD(1/2)
(TRV330/TRV530)
Q405,408-412
F405
36
38
40
30
32
34
30
32
34
(TRV230)
15
16
15
16
F401
17
17
F403
20
20
21
21
24
24
25
25
28
28
(TRV230/TRV330)
FU-154 BOARD(1/2)
F406
(TRV530)
Q407,
409,410
BATTERY
TERMINAL
6
5
1
BATT UNREG
Q401,
402
BATT SIG
Q403,
404
CHARGE
SWITCH
BATT GND
F404
DC IN
L401
F402
19
SHOE/PRT UNREG
20
CN1101
VC-254 BOARD(1/2)
INTELLIGENT
ACCESSORY
SHOE
BL CONT
BL REG
PANEL 2.8V
PANEL 13.3V
PANEL 4.75V
PANEL -15.3V
BATT UNREG
4
3
8
6
7
5
TO
POWER
BLOCK(3/3)
(PD-138/139)
(SEE PAGE 3-15)
CN1120
BATT UNREG
Q1311,1312,1327
C/D VS D1.5V
MT 5V
5V REG
BL UNREG
VTR UNREG
VTR UNREG
CN403
BATT/XEXT SW
SHOE ON
CN401
INIT CHARGE ON
3
2
ACV UNREG
FAST CHARGE
SHOE ON
17
18
PRT HEAD UNREG
CN1113
3 4
14
5 2
3 4
14
BATT SIG
(449)
INIT CHARGE ON
Q1309
SWITCHING
IC1301
L1317
L1318
VTR DD ON
BL REG
DC/DC CONVERTER
CN403
5 2
BL CONT
BL CONT
NONINV
7 INPUT7
31 STANDBY7
CAM DD ON
FAST CHARGE
OUTPUT7 2
OUTPUT
MONITOR-7 6
BATT/XEXT SW
(MS MODEL)
L1319
OUTPUT VCC7
OUTPUT VCC4,5,6
Q1303
SWITCHING
L1305
PC 1.9V
L1310
D 1.9V
Q1331,1332
OUTPUT4
57
MOS GATE4
54
Q1308
SWITCHING
28 VCC
IC1304
D 1.5V
1.5V REG
OUTPUT
MONITOR4 18
COMP
(450)
41
(SEE PAGE 3-13)

L302
L1306
Q1314
OUTPUT1
45
MOS GATE1
42
OUTPUT
MONITOR1
40
Q1307
SWITCHING
49
OUTPUT3
50
OUTPUT MONITOR3
34
Q1301
SWITCHING
5
4
VREF
27 VREF
1
7
8
3
Q1302
SWITCHING
22 CT
OUTPUT2
VTR DD ON
D1302 (1/2)
RECT
30 STANDBY
OUTPUT
MONITOR2
A 2.8V
L1308
AU 2.8V
L1309
EP 2.8V
L1320
13.3V REG
2
5
5.9V REG
RP 6.0V
(450)
Q1316,1329
D1302(2/2)
RECT
EP 13.3V
IC1303
D1306
RECT
-7.5V REG
L1313
L1301
D1301,1305
46
RECT
29 STANDBY3
Q1321,1323
Q1333
2
21 RT
EMERGENCY
DETECT
D 2.8V
L1307
15V REG
T1301
OUTPUT VCC1,2,3
Q1324,1330
AU 4.75V
L1314
A 4.75V
L1315
EVF BL 4.75V
L1316
RP 4.75V
-15.3V REG
Q1305
SWITCHING
OUTPUT MONITOR6
NONINV INPUT6
L1303
CAP VS
(TRV230/TRV330)
CAP VS
64
DRUM VS
10
11
L1304
DRUM VS
CD-315
BOARD
(TRV530)
D 2.8V
A 4.75V
OUTPUT MONITOR5 14
DRUM ERROR
IC501
CN1501
CAM 15V
CAM -7.5V
10
12
CCD
IMAGER
7
5
CN501
16
3-11
(TRV230/TRV330)
TIMING
GENERATOR
FB1501
OUTPUT5 58
NONINV INPUT5 15
IC1501
DRUM ERROR
CAP ERROR
Q1306
SWITCHING
CD-292
BOARD
(416)
37
CAP ERROR
OUTPUT6
TO
POWER
BLOCK(2/3)
VREF
Q1304
SWITCHING
CAM DD ON
BT901
CN1113
36
38
40
3-12
(4-10)

(SS-1380) (SEE PAGE 4-101)
FU-150 BOARD FU-154 BOARD

(2/2)(TRV230/TRV330) (2/2)(TRV530)
VC-254 BOARD(2/2)
BATT LI3V
(SEE PAGE 4-101)
IC4803 (4-34)
HI CONTROL
SHOE ON
BATT SIG
INIT CHARGE ON
VTR DD ON
CAM DD ON
FAST CHARGE
BATT XEXT SW
(4-33)
IC4801 (4-33)
IC4804
D4806
BATT UNREG
D4802
3
CHARGER
RESET
BATTER IN
DETECT
REG
IC4802 (4-33)
61 BATT IN
1 UNREG
LANC DC
14 LANC DC
20
5
4
30
37
BT101
LITHIUM
BATTERY
(4-40)
(4-45)
(4-44)
IC5701
IC5702
IC5801
AUDIO I/O
AUDIO
ADC&DAC
MIC AMP
(4-39)
24
IC4502
IC4501
EEPROM
DIGITAL8
MECHA
CONTROL
22
L5701
TO
POWER BLOCK
(1/3)
AU 2.8V
(SEE PAGE
3-12)
D 1.5V
42
FB4501
FB3701
LANC DC
D 2.8V
IC3603
IC3701
IC3301
IC3303
(ALIGN)
A/D CONV.
(TAXO)
VIDEO
LINE IN/OUT
AMP
(CAIN)
DV
SIGNAL
PROCESS
(LIP)
DV
INTERFACE
70
CAP ERROR
DRUM VS
L2209
(4-23)
(4-23)
IC2291
(EVR)
D/A CONV.
L2291
78
79
(4-37)
80
4
12
26
FB2202
FB2205
L2202
L2208
FB2204
L1501
FB1504
IC2201
IC1502
CAMERA PROCESS
HI8/STD8
PB Y/C
PROCESS
S/H,AGC,
A/D CONV.
(4-17)
IC2001
(4-16)
PITCH/
YAW
SENSOR
AMP
RP 4.75V
A 2.8V
RF 1.9V
L3102
L3201
L3104
L3103
IC3202
IC3103
IC3101
HI8/STD8
PB RF
AMP
RF ENV
DET
(TRW)
REC/PB
AMP
(TRF)
EQ.
A/D CONV.
PLL
(4-31)
(4-32)
(4-26)
(4-35)
(4-35)
IC4901
IC4902
EEPROM
CAMERA
CONTROL
HI8/STD8
MECHA
CONTROL
(4-36)
IC3201
RP 6.0V
CN104
2
R113
DISP LCD VDD

Q102
VTR UNREG
LED
TO
POWER
BLOCK
(3/3)
(PD-138/139)
DISP BL
D 1.5V
FP-275
(FLEXIBLE)
(SEE PAGE 4-76)
(SEE PAGE 3-15)
PC 1.9V
D 2.8V
A 4.75V
TO
POWER
BLOCK(3/3)
(PC-082)
IRIS DRIVE
(SEE PAGE
3-16)
L1553
L1551
24
IRIS
METER
16
ZOOM
RESET
SENSOR
14
FOCUS
RESET
SENSOR
18
TEMP
17
CAPSTAN
FG
T REEL,
S REEL
SENSOR
Q1555
IC1553
ZOOM/
FOCUS
MOTOR
DRIVE
(SEE PAGE 3-15)
A 4.75V
R1560
(4-20)
TO
POWER
BLOCK(3/3)
(SI-028/029)
MT 4.75V
LENS ASSY
(4-20)
(TRV330/TRV530)
A 4.75V
SE 2.8V
VTR UNREG
(FLEXIBLE)
IC1552
L1552
CAP VS
IR
TRANSMITTER
(TRV530)
(4-42)
CN1551
IC4402
IC3901
DRUM ERROR
RP 4.75V
CHARACTER
GENERATOR
71
72
CN1116
L2204
LED
D 2.8V
EVER 3.0V
LB-070 BOARD
(4-77)
10
L2001
(4-38)
CAP VS
(4-21)
IC3302
A 4.75V
A 2.8V
MT 5V
D 1.5V
D 2.8V
L3901
(4-77)
CN103
CN1104
FB2291
L3701,
3705
A 4.75V
TIMING
GENERATOR
(4-85)
FP-272
FB3370
(4-28)
LCD
DRIVE
EVF
BACKLIGHT
DRIVE
CN1114
EVER 3.0V
(4-30)
IC202
(4-42)
CAPSTAN MOTOR
DRIVE
2
1
IC4401
(RABI)
DRUM ERROR
29
CAP ERROR
27
DRUM VS
6
DRUM
MOTOR DRIVE
DRUM FG,PG AMP
LOADING
MOTOR DRIVE
REEL FG AMP
TAPE TOP,END DET
DRUM,CAP ERROR AMP
CN4403
SENSOR VCC
R4407
H001,002
FB4901
D 2.8V
VTR UNREG
MT 5V
TAPE LED(A)
R4411
(4-25)
12
CN4404
D001
TAPE LED
M2000 MECHA
DECK
(SEE PAGE 4-52)
16
3-13
LCD
UNIT
IC701
LCD LED ON
A 2.8V
AU 2.8V
D 2.8V
L3602
44
IC201
CN1117
FB3303
FB3601
FB201
S101
2
D 1.9V
A 2.8V
CN701
RESET
16
8
7
1
CN702
20
1
1
20
FB202
LCD903
(TRV230/TRV330)
CN201
L201
XPHOTO STBY SW 20
L5803
CAMERA
MEMORY (TRV330/TRV530)
LB-068 BOARD
(TRV530)
EVF 4.75V
EVF 13.3V
EVF 2.8V
VCC 8
(4-43)
AU 4.75V
26
41
42
12 XLANC ON
Q4806
VTR UNREG
MT 5V
AU 2.8V
EP 2.8V
EP 13.3V
EVF BL 4.75V
PC 1.9V
EVF BL 4.75V
EP 13.3V
EP 2.8V
(TRV230/TRV330)
XCAM MODE SW 15
POWER 4
OFF(CHG)
CF-079 BOARD CF-080 BOARD

CN102
XVTR MODE SW 14
1
4
3
CN402
CN403
FAST CHARGE 50
CAM DD ON 15
BATT/XEXT 66
LANC I/O
VTR UNREG
I/F
BATT SIG
INIT CHARGE ON 25
VTR DD ON 29
38 XRESET
42 51
VDD
86 87
5
6
MT 5V
Q4804
IB SO 49
IB SI 48
VCR
XVTR MODE SW
XCAM MODE SW
XPHOTO STBY SW
8
7
10
8
7
10
SHOE ON 81
90 BATT SENS
91 ACV SENS
POWER
CN1113
3-14
J201
LANC

PD-138/139
BOARD
PD-139 BOARD(TRV530)
Q5505,5506
PANEL 13.3V
FB5504
18
FB5502
PANEL 2.8V
(4-62)
LCD901
PC-082 BOARD
16
D5503
LCD
UNIT
CN1901
A 4.75V
80
IC5501
IC5502
RGB DRIVE
14
TIMING
GENERATOR
(4-95)
TO
POWER
BLOCK(2/3)
(VC-254)
(4-95)
(SEE PAGE
3-14)
PD-138 BOARD(TRV230/TRV330)
IC1158
PANEL 4.75V
PANEL -15.3V
PANEL 13.3V
PANEL 2.8V
FB5504
FB5503
FB5502
L5501
TO
POWER BLOCK
(1/3)
(VC-254)
(4-55)
IC5501
IC5502
RGB DRIVE
28
TIMING
GENERATOR
(4-89)
(SEE PAGE
3-12)
24
3
1
23
CN5501
PC 1.9V
FB1154
L1151
D 1.5V
FB1152
FB1153
LCD
UNIT
IC1901
IC1155
(L-PLATZ)
(KATHMANDU)
DS STILL
PROCESS
DIGITAL
STILL
CONTROL
(4-64)
(4-59)
IC1154
IC1153
4MBIT
FLASH
MEMORY
16MBIT
SDRAM
(4-62)
33
MS VCC ON
IC5601,5602
INVERTER
4
3
BL CONT
BL REG
BACKLIGHT
DRIVE
BL HIGH
IC1151
10
CN5604
XTAL
OSC
(PD-138 4-91)
(PD-139 4-97)
(4-59)
IC5701
TO
POWER
BLOCK(2/3)
(CF-079/080)
(SEE PAGE
3-14)
DISP LCD VDD
INDICATOR
DIRVE
D902
BL VDD
DISP BL
CN5704
CN5705
21
(TRV330/TRV530)
CHARACTER
DISPLAY
BACKLIGHT
SI-028 BOARD SI-029 BOARD

(TRV230/TRV330)
(TRV530)
D307,D308
26
L301
VTR UNREG
F301
LASER LINK
NIGHT SHOT
LED
SE301,302
TO
POWER BLOCK
(2/3)
(VC-254)
12
SE 2.8V
PITCH/YAW
SENSOR
IC301
(SEE PAGE
3-14)
4
REMOTE
COMMANDER
RECEIVER
A 4.75V
CN304
R301
(4-82)
16
CN301
MF PHOTO
SENSOR
3-15
IC1152
IC1159
IC1160
BUFFER
(4-59)
(PD-138 4-91)
(PD-139 4-97)
FB1151
LCD901
ND901
BACKLIGHT
(4-89)
FB1158
3
D 2.8V
FB1902 FB1903
7
5
6
8
FB1156
3.1V
REG
2
5
Q1155
7
11
CN1153
79
78
72
71
70
Q5502,5509-5511
CN5701
USB
I/F
(4-62)
CN5501
L5501
IC1157
FP-273
(FLEXIBLE)
(SEE PAGE 4-81)
3-16E
(4-61)
MEMORY
STICK
SLOT
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/3)
2
CD-292 BOARD
CD-315 BOARD
A
LENS UNIT
11
10
12
(DCR-TRV230/TRV330)
(DCR-TRV530)
FP-272
CCD
IMAGER
J201
16P
FLEXIBLE
LANC
A_4.75V
GND
1
1
V4
CCD_OUT
2
2
V3
GND
3
3
V2
CAM-7.5
4
4
V1
VSHT
5
5
GND
6
6
GND
RG
7
7
H1
H2
8
8
H2
H1
9
9
10
GND
RG
11
10
GND
12
CAM_15V
V1
13
11
V2
14
VSHT
V3
15
12
V4
16
TPA
NTPA
TPB
NTPB
REG_GND
NTPB
TPB
TPA
NTPA
CN1114
10P
REG_GND
REG_GND
LANC_SIG
10
LANC_DC
XLANC_JACK_IN
FLEXIBLE
CN1501
CN1551
DV IN/OUT
CAM-7.5
24
13
23
IRIS_DRIVE(+)
GND
22
IRIS_HALL(+)
14
21
IRIS_BIAS(+)
15
20
IRIS_HALL(-)
GND
19
IRIS_BIAS(-)
CCD_OUT
18
IRIS_DRIVE(-)
16
17
TEMP
A_4.75V
16
TEMP
16P
15
ZM_SENSE_VCC
ZOOM_A
14
10
ZOOM_B
GND
8
ZOOM_XB
13
7
ZOOM_XA
FC_SENSE_VCC
6
IR_SWITCH
12
5
IR_SWITCH
FC_SENSE_OUT
4
FOCUS_A
11
3
FOCUS_B
N.C.
2
FOCUS_XB
ZM_SENSE_OUT
1
FOCUS_XA
FP-265
24P
CAM_15V
CN501
CN202
14
13
VC-254 BOARD(1/3)
FP-270
C
Y
S
S
G
AUDIO/VIDEO
EXT_MIC_L
SE_GND
LIA1
VREF1
LIA2
VREF2
XF_TALLY_LED
VTR_UNREG
19
20
21
22
23
24
25
26
EXT_MIC_L
SE_GND
LIA1
VREF1
LIA2
VREF2
XF_TALLY_LED
VTR_UNREG
26P
EXT_MIC_R
9
18
EXT_MIC_R
SHOE_MT_GND
SHOE_UNREG_GND
SHOE_UNREG_GND
SHOE_UNREG_GND
CN1101
20P
CN1115
10P
S_Y_I/O
XS_JACK_IN
AUDIO_L_I/O
AV_JACK_IN
VIDEO_I/O
AV_GND
CN1116
AU_GND
10
17
EXT_MIC_GND
AU_GND
11
16
INT_MIC_GND
INT_MIC_R
12
15
INT_MIC_L
13
INT_MIC_R
REG_GND
14
14
SE_2.8V
15
INT_MIC_L
IR_DRV_EM
13
SIRCS_SIG
16
12
HP_GND
17
SE_2.8V
HP_L
18
REG_GND
HP_R
19
11
HP_JACK_IN
20
IR_DRV_EM
MF_LED
21
10
SHOE_MT_GND
FLEXIBLE
CN301
SI-028 BOARD
14P
MF_A
REG_GND
MF_4.75V
(DCR-TRV230/TRV330)
MF_LED
CN302
J102
SIRCS_SIG
SHOE_MIC_L
S_GND
HP_GND
15
SHOE_CONT_AD
GND
S_GND
HP_L
SHOE_MIC_GND
14
S_C_I/O
HP_R
13
MIC_L
MT_GND
FLEXIBLE
S VIDEO
HP_JACK_IN
FP-266
2
CTSHDS
MF_A
12
REG_GND
11
26P
MIC_GND
SHOE_CONT_AD
G
J101
10
A_4.75V
STB_ON
CTS
22
RTSSCK
10
CN304
STB_ON
SHOE_ID2
11
MF_LED
RXD
12
RTS
MF_B
SHOE_ID1
13
23
TXD
14
SHOE_ID2
24
LANC_SIG
15
RXD
PRT_HEAD_UNREG
16
SHOE_ID1
PRT_HEAD_UNREG
17
TXD
MF_B
18
A_4.75V
MF_A
SHOE/PRT_UNREG
LANC
TO VC-254 BOARD(2/3)
25
SHOE/PRT_UNREG
19
16/18 MIC AMP

17/18 CONNECTOR
18/18 DC/DC CONVERTER
REG_GND
20
10/18 MODE CONTROL

11/18 CAMERA CONTROL,
HI8/STD8 MECHA CONTROL,
STEADY SHOT
12/18 EVR,LASER LINK
13/18 DIGITAL8 MECHA CONTROL
14/18 DRUM/CAPSTAN DRIVE
15/18 AUDIO PROCESS
26
HEAD_UNREG
FLEXIBLE
SHOE_UNREG
FP-264
INTELLIGENT
ACCESSORY
SHOE
1/18 CAMERA PROCESS

2/18 CAMERA PROCESS,HI8/STD8
PB PROCESS
3/18 IRIS/FOCUS/ZOOM DRIVE
4/18 DV SIGNAL PROCESS-1
5/18 DV SIGNAL PROCESS-2
6/18 DIGITAL8 PB RF AMP
7/18 VIDEO IN/OUT
8/18 VIDEO AD CONVERTER
9/18 HI8/STD8 PB RF AMP
MIC901
L-CH
MIC
INT_MIC_L
GND
2P
SI-029 BOARD
(DCR-TRV530)
2P
MF_B
REG_GND
HP_R
HP_JACK_IN
CN303
FP-273
J302
MIC
(PLUG IN POWER)
FLEXIBLE
HP_L
HP_GND
10
J301
(HEADPHONES)
10
AUDIO_R_I/O
MIC902
R-CH
MIC
INT_MIC_R
SE302
SE301
MIC_GND
11
GND
YAW
SENSOR
PITCH
SENSOR
MIC_GND
12
IC301
(CIRCCS)
D306
(TALLY)
D307,D308
(LASER LINK)
EXT_MIC_L
13
EXT_MIC_R
14
16
4-1
4-2
FRAME SCHEMATIC DIAGRAM (1/3)

3
4
FP-275
FLEXIBLE
7
FP-282
S405/
D401
10
14
16
15
17
S103/S102
FLEXIBLE
S401-404,S406-409
13
12
11
CONTROL SWITCH
BLOCK(SE-1380)
SEL/PUSH EXEC
S101
FF,
REC,
PANEL OPEN/CLOSE
S501
STOP ,SUPER NIGHT SHOT,

PAUSE,
REW, PLAY
FOCUS
EXPOSURE
S910
AUIOMANUAL
SUPER LASER LINK
41
EVF_B
40
EVF_B
39
BW_Y
EVF_R
38
EVF_R
PANEL_XHD
37
PANEL_XHD
10
PANEL_XVD
35
11
XCS_EVF
34
12
XHI_SCK
30
16
VG
VR
29
17
VB
28
18
VB
XTALLY_LED
27
19
XTALLY_LED
26
20
EVF_4.75V
VG
13
VG
VR
12
VR
VB
10
11
VB
BLK
11
10
BLK
HCK1
12
HCK2
13
OPEN/CLOSE
REG_GND
HCK1
HCK2
MENU,MS+/-,END SEARCH,MS INDEX,DISPLAY

TITLE,MS DELETE,PB ZOOM,VOLUME+/MS PLAY,MS MIX,FADER,BACK-LIGHT
EDIT SEARCH+/-,RESET
SP_+
12
34
SP_+
SP_-
11
35
SP_-
REG_GND
10
36
REG_GND
12
13
14
15
16
17
18
19
20
21
22
23
24
CLS
RES
PSS1
PSS2
CTR
CLD
SPD
VR
VG
VB
GND
VSH3V
VSH5V
11
MO2
10
6
EX1
MO1
EX2
5
SPS
VCOM
4
VGLAC
PSG
16
14
VR
15
13
VB
COM
12
BLK
VG
11
13
SEG1
12
SWP
SEG10
11
SEG9
AFC_FO
10
SEG8
SEG7
SEG2
SEG6
SEG5
1/2 RGB DRIVE,TIMING GENERATOR
SEG4
2/2 LCD DRIVE,BACK LIGHT DRIVE
SEG3
COM2
COM1
VP-076
20P
XSYS_RST
20
AD5
19
PANEL_R
BPF_MONI
18
HARNESS
SE_GND
BL_GND
BL_REG
F0_ADJ_RF_IN
PANEL_G
17
BL_CONT
PB_RF
PANEL_B
16
PANEL_-15.3V
PANEL_XHD
REG_GND
PANEL_XVD
RF_AGC_OUT
HI_SO
VC_RF_SWP
EVF_VR
COM.DC
10
EVF_VB
N.C
Note
15
14
13
6
7
8
PD-138 BOARD
PD-139 BOARD
13
WIDE
15
14
CS
VVSSG
16
(DCR-TRV230/TRV330)
(DCR-TRV530)
PANEL_13.3V
PANEL_4.75V
PANEL_2.8V
XCS_LCD
12
REG_GND
XHI_SCK
11
10
REG_GND
CN5502
11
VCO
12
EVF_VG
13
DV_RF_SWP
14
RF_IN
15
16
17
REG_GND
10
11
XHI_SCK
D902
(BACKLIGHT)
LCD 902
CHARACTER
DISPLAY
10P
CN5705
22P
CN5703
6P
VB
XVD_OUT
VG
PANEL_COM/PSIG
PANEL_REV
REG_GND
12
XCS_LCD
PANEL_2.8V
13
HI_SO
PANEL_4.75V
14
PANEL_XVD
CAP_FG
PANEL_13.3V
15
PANEL_XHD
VR
PANEL_REV
FP-283
RF_MON
PANEL_-15.3V
16
PANEL_B
MAKER_CHECK
N.C.
FLEXIBLE
TMS
BL_CONT
17
PANEL_G
XHD
N.C.
18
TCK
BL_REG
18
PANEL_R
XHD_OUT
GND
19
TDO
BL_GND
19
AD5
GND
GND
SE_GND
20
XSYS_RST
10
GND
CPC
TDI
CN1120
20P
CN5701
20P
Note:
Suffix NO. -12 of CF-079 BOARD ONLY
Suffix NO. -13 of CF-080 BOARD ONLY
16
4-3
HCK1
14
SEG15
24P
1
20
10
HST
15
SEG16
(FOR CHECK)
HCK2
SEG11
(FOR CHECK)
RGT
16
CN5501
CN1108
CPC
17
SEG12
EN
18
SEG13
VDOG
DISP_BL
17
18
VSS
DISP_BL
19
SEG14
VDD
DISP_LCD_VDD
DWN 19
20
20
COM3
EN
DISP_LCD_VDD
VGL
21
COM4
21
XOSD_SCK
VCK
OSD_SO
22
CN5501
VGH
22
BL_VDD
24
OSD_SO
XOSD_SCK
GND
BL_GND
TEST1
6P
23
LCD_COM/XDATA
VST
XCS_LCD_DRIVER
COM
24P
CN5704
1
LCD_COM/XDATA
6P
XCS_LCD_DRIVER
CN103
10
REG_GND
N.C
45
N.C
BL_HIGH
VTR_UNREG
REG_GND
LCD_LED_ON
44
EVER_3.0V
43
N.C
42
N.C
EVER_3.0V
VTR_UNREG
N.C
XOSD_SCK
4
OSD_SO
41
LCD_COM/XDATA
40
N.C
39
BL_LOW
OSD_SO
XOSD_SCK
LCD_COM/XDATA
LED
XCS_LCD_DRIVER
BATT_LI_3V
38
10P
37
CN5604
LED_GND
LCD 901
2.5,3.5INCH
COLOR LCD UNIT
BATT_LI_3V
XCS_LCD_DRIVER
LCD_LED_ON
BACKLIGHT
FP-277
REG_GND
(DCR-TRV530)
33
FLEXIBLE
13
EVF_VDD
(DCR-TRV230/TRV330)
DIAL_B
REG_GND
EVF_GND
FLEXIBLE
DIAL_A
32
VST
20
FP-276
XHI_RESET
31
14
19
(PD-138 BOARD)
30
15
DIAL_B
18
EVF_VDD
(PD-139 BOARD)
16
DIAL_A
VST
EVF_GND
XHI_RESET
VCK
TEST2
MS_LED
29
(BACKLIGHT)
17
17
D701
STB
VCK
MS_LED
EN
KEY_AD4
16
28
15
STB
RGT
KEY_AD3
HST
EN
KEY_AD2
27
(DCR-TRV530)
26
(DCR-TRV230/TRV330)
14
KEY_AD0
18
LB-068 BOARD
LB-070 BOARD
HST
PSIG
25
DWN
SEIDEN_GND
N.C
SEIDEN_GND
REG_GND
2
REG_GND
1
REG_GND
FOCUS_AUTO
DIAL_A
EXPOSURE
D_2.8V
REG_GND
KEY_AD1
DIAL_B
XIR_LED_ON
REG_GND
MENU_EXE
KEY_ADO
8P
BT101
LITHIUM BATTERY
XIR_LED_ON
KEY_AD4
VC-254 BOARD(2/3)
16P
COM
<S101-118>
ND901
14
FLAT
CABLE
HCK1
KEY_AD1
19
EVF_GND
COM
23
20
15
23
KEY_AD3
HCK2
KEY_AD1
KEY_AD2
EVF_GND
EVF_GND
CRext
D_2.8V
21
LED_ON/OFF
16
10
22
KEY_AD0
LED_DA
17
LED_DA
EVF_DO_ON
24
24
REG_GND
VR
D_2.8V
FFC-001
18
EVF_GND
LED_ON/OFF
FP-268
VG
22
20P
(3.5 INCH LCD MODEL)
1/2 USER FUNCTION

2/2 EVF DRIVE
FLEXIBLE
VCO
21
XTALLY_LED
XSYS_RST
15
25
EVF_4.75V
19
HI_SO
31
EVF_4.75V
20
SOUT
14
11
32
CN701
EVF_4.75V
XTALLY_LED
(2.5 INCH LCD MODEL)
12
13
VCO
XIR_LED_ON
33
CF-079 BOARD
CF-080 BOARD
CN702
36
XHI_SCK
EVF_DO_ON
CN201 20P
XCS_EVF
XSYS_RST
EVF_13.3V
PANEL_XVD
HI_SO
EVF_13.3V
EVF_G/BW_Y
1
STB
EVF_2.8V
REG_GND
VST
42
SP(+)
VCK
43
EVF_2.8V
SP(-)
REG_GND
CN101 2P
VSS
REG_GND
VDD
2P
44
CN105
REG_GND
45P
6P
REG_GND
CN107
CN106 6P
45
REF
TO VC-254
BOARD(1/3)
REG_GND
LCD 903
B/W LCD UNIT
SP901
SPEAKER
HST
CN102
45P
CN104
CN1117
SEIDEN_GND
S_NIGHT_SW
4-4
S601
(PANEL REVERSE)

1
11
10
12
14
13
15
16
17
18
19
20
DCR-TRV330/TRV530
PC-082 BOARD
1/3 DIGITAL STILL CONTROL1

100
REG_GND
REG_GND
99
100
REG_GND
REG_GND
99
98
REG_GND
REG_GND
97
98
REG_GND
REG_GND
97
96
REG_GND
DS_MAD
95
96
REG_GND
DS_MAD
95
94
MS_LED
XDS_FLASH_RST
93
94
MS_LED
XDS_FLASH_RST
93
92
RTS/IR_L
90
TXD/IR_R
88
AUDIO_MUTE
86
ADAO2
84
SSS_FROM_L
2/3 DIGITAL STILL CONTROL2

3/3 DS STILL PROCESS
ADAI2
85
REG_GND
83
REG_GND
FLEXIBLE
5
XWEN_FROM_VC 81
A_4.75V
D_2.8V
79
80
A_4.75V
D_2.8V
79
D_2.8V
REG_GND
77
78
D_2.8V
REG_GND
77
76
REG_GND
VSP_SI
75
76
REG_GND
VSP_SI
75
74
SFD_LRCK
SFD_BCK
73
74
SFD_LRCK
SFD_BCK
73
72
PC_1.9V
PC_1.9V
71
72
PC_1.9V
PC_1.9V
71
70
D_1.5V
XSYS_RST
69
70
D_1.5V
XSYS_RST
69
XCS_DS
67
XDS_WAKE_UP
FU-154 BOARD
12P
CN1153
65
58
VFIO_C5
TCK
55
56
VFIO_C4
VSP_SO
53
54
IFI_C7
52
IFI_C6
TDI
51
50
IFI_C5
MS_IN
49
48
IFI_C4
SPCK0
47
MS_DIO
MS_INSERT
AFCK
MS_VCC
11
DS_XRESETM
GND
12
VFO_HD
VFI_Y1
VFO_HD
VFI_Y1
VFI_HD
VFI_Y0
VFI_HD
VFI_Y0
REG_GND
REG_GND
REG_GND
S004
PHOTO
(PHOTO FREEZE)
RV001
W
T
D_2.8V
10
S001
ZOOM_VR
11
POWER
XEJECT_SW
12
VCR
42
44
46
48
REG_GND
REG_GND
MEMORY
REG_GND
REG_GND
DC IN
6P
BATT_GND
BATT/XEXT
ACV_GND
ACV_UNREG
BATT_SIG
BATT_UNREG
BT901
BATTERY
TERMINAL
REG_GND
REG_GND
REG_GND
REG_GND
FAST_CHARGE
BATT/EXET_SW
XCAM_MODE_SW
XEJECT_SW
KEY_AD1
D_2.8V
BATT_UNREG
C/D_VS_D1.5V
C/D_VS_D1.5V
BL_REG_UNREG
BL_REG_UNREG
VTR_UNREG
VTR_UNREG
SHOE_GND
SHOE_GND
SHOE_GND
SHOE_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
CN1113
ZOOM_VR_AD
1
TAPE_TOP(C)
TAPE_END(C)
15
11
REG_GND
TAPE_TOP(C)
10
11
S_REEL(-)
SENSOR_VCC
10
T_REEL(+)
9
9
S_REEL(+)
T_REEL(-)
8
8
SENSOR_VCC
HALL_COM
7
7
T_REEL(+)
ME/MP
6
6
5
5
T_REEL(-)
REC_PROOF
HALL_COM
HI8_MP
DEW
22
M-SW(A)
21
M-SW(B)
20
M-SW(C)
19
FG1
18
FG VCC
17
ME/MP
FG2
16
HI8_MP
REG_GND
15
REC_PROOF
CAP_U
14
C_LOCK_SW
CAP_U
13
CN4404 15P
CAP_W
12
CAP_W
11
TAPE_LED(K)
CAP_V
10
15
CAP_V
9
TAPE_LED(A)
VH+
8
14
Hu1
7
14
Hu2
6
TAPE_END(C)
Hv1
5
REG_GND
Hv2
4
13
Hw1
3
13
Hw2
2
TAPE_LED(K)
VH1
S_REEL(-)
FE(X)
12
FE(Y)
12
GND
11
FP
TAPE_LED(A)
YEVEN(SP2Y)
10
0.5
XEVEN(SP2X)
FP
S_REEL(+)
NON.ZIF
22P
GND
YODD(SP1Y)
5
XODD(SP1X)
4
GND
3
FP
CN4403
11P
U
10
GND
U
9
GND
V
8
V
7
COM
W
6
FG
3
FG-PG_COM
PG
CN4402
LM(-)
LM(+)
CN3101
10P
CN4401
2P
48P
VC-254 BOARD(3/3)
PRT_HERD_UNREG
B TO B
PRT_HERD_UNREG
100P
PRT_HEAD_UNREG
CN1901
SHOE/PRT_UNREG
100P
REG_GND
REG_GND
SHOE/PRT_UNREG
CN1104
47
SHOE/PRT_UNREG
48
VFI_Y2
45
11
VFI_Y3
VFI_VD
46
VFI_Y4
VFO_VD
43
VFI_OE
10
41
12
44
11
VFI_Y3
VFI_VD
42
VFI_Y4
VFO_VD
39
VFI_OE
10
40
13
37
VFI_Y5
38
VFO_OE
35
14
36
13
33
VFI_Y5
31
VFO_OE
34
14
32
15
29
17
VFI_Y6
30
VFI_Y7
VFO_Y0
27
VFO_Y1
16
28
18
15
25
17
VFI_Y6
26
VFI_Y7
VFO_Y0
23
VFO_Y1
16
21
18
24
19
22
21
IFI_Y0
19
23
IFI_Y1
VFO_Y2
20
IFI_Y2
VFO_Y3
20
17
VFO_Y4
22
19
15
24
21
IFI_Y0
13
23
IFI_Y1
VFO_Y2
18
IFI_Y2
VFO_Y3
20
16
VFO_Y4
22
14
24
VFI_Y2
CAMERA
CN401
11
25
12
IFI_Y3
VFO_Y5
26
25
10
IFI_Y3
BATT_SIG
2
VFO_Y5
27
26
29
IFI_Y4
B TO B
IFI_Y5
VFO_Y6
48P
31
VFO_Y7
28
CN403
IFI_Y6
30
27
ZOOM_VR_AD
VFI_C0
29
IFI_Y4
32
IFI_Y5
VFO_Y6
31
VFO_Y7
28
VFI_C0
30
40
IFI_Y6
32
REG_GND
33
REG_GND
IFI_Y7
REG_GND
VFI_C1
REG_GND
34
38
33
36
IFI_Y7
PRT_HERD_UNREG
VFI_C1
REG_GND
34
34
35
PRT_HERD_UNREG
IFI_OE
REG_GND
VFI_C2
32
36
PRT_HEAD_UNREG
35
SHOE_GND
IFI_OE
30
VFI_C2
SHOE/PRT_UNREG
37
36
SHOE/PRT_UNREG
39
IFI_VD
SHOE_GND
41
IFI_HD
VFI_C3
SHOE_GND
KASYAON
IFI_C0
38
28
IFI_C1
40
37
26
42
39
IFI_VD
SHOE/PRT_UNREG
41
IFI_HD
SHOE_GND
KASYAON
IFI_C0
VFI_C3
24
IFI_C1
38
12
OFF(CHG)
KEY_AD1
XPHOTO_FREEZE
43
BATT_SIG
OPEN/EJECT
45
VTR_UNREG
IFI_C2
10
VTR_UNREG
44
IFI_C3
MS_SCLK
VTR_UNREG
46
40
42
MS_VCC
MEMORY
STICK
CONNECTOR
22
43
VTR_UNREG
DS_BUSY
VTR_UNREG
IFI_C2
45
GND
MS_BS
VTR_UNREG
AFCK
53
20
44
IFI_C3
55
BL_REG_UNREG
47
TCK
VSP_SO
BL_REG_UNREG
49
SPCK0
BL_REG_UNREG
MS_IN
IFI_C4
BL_REG_UNREG
IFI_C5
48
57
BL_REG_UNREG
50
TMS
BL_REG_UNREG
51
XS/S_SW
REG_GND
18
TDI
XCAM_MODE_SW
16
IFI_C6
S002
START/STOP
C/D_VS_D1.5V
52
N.C
C/D_VS_D1.5V
IFI_C7
S_GND
C/D_VS_D1.5V
VFIO_C4
54
S_GND
C/D_VS_D1.5V
56
59
57
VFIO_C5
REG_GND
XPHOTO_STBY_SW
61
TMS
58
46
TD_2-3
XVSP_SCK
C/D_VS_D1.5V
VFIO_C6
C/D_VS_D1.5V
VFIO_C7
60
14
62
59
S003
BATT_UNREG
61
XVSP_SCK
CONTROL SWITCH
BLOCK(SS-1380)
12P
XVTR_MODE_SW
(DCR-TRV530)
INIT_CHARGE_ON
TD_2-3
VFIO_C6
CN402
63
BATT_UNREG
VFIO_C7
60
BOARD TO BOARD
62
XCS_HONEY
D_2.8V
XHI_SCK
BATT_UNREG
HI_SI
64
INIT_CHARGE_ON
66
63
68
65
(DCR-TRV230/TRV330)
12
HI_SO
67
DIGITAL I/O
(USB)
CN201
FU-150 BOARD
S_GND
XCS_HONEY
VCC
XPHOTO_FREEZE
XDS_WAKE_UP
6P
KEY_AD1
XHI_SCK
2
1
D-
XPHOTO_FREEZE
HI_SI
64
USB_D+
USB_VCC
ID
D+
66
CN1152
10
XCS_DS
HI_SO
68
USB_D-
XVTR_MODE_SW
SSS_FROM_VC
GND
XPHOTO_MODE_SW
82
FLEXIBLE
XWEN_FROM_VC 81
78
80
SSS_FROM_VC
XWEN_FROM_L
FP-274
82
XWEN_FROM_L
XEJECT_SW
SSS_FROM_L
REG_GND
XCAM_MODE_SW
DATA_FROM_SFD
84
87
XVTR_MODE_SW
86
83
89
XPHOTO_STBY_SW
85
91
ADAI2
FP-271
HDS
RXD
USB_DET
XS/S_SW
AUDIO_MUTE
SHOE_ON
TXD
88
BATT/EXET_SW
90
87
XS/S_SW
92
89
FAST_CHARGE
91
SHOE_ON
SCK
CTS
RXD
USB_DET
FP
M903
LOADING
MOTOR
21
22
DEW
C_LOCK_SW
Vcc
20
17
Vo2
16
GND(COM)
19
15
14
Coil-U
18
13
Coil-U
Vo1
12
Coil-V
Hu1
11
Hu2
coil-V
Hv1
Coil-W
10
M902
CAPSTAN
MOTOR
MR
SENSOR
FP-300
Q001
TAPE TOP
FLEXIBLE
LS-057 BOARD
SP1
VIDEO
HEAD
FP-228
FLEXIBLE
FP-229
FLEXIBLE
SP2
S901
DEW
SENSOR
Hv2
Coil-W
Hw1
FE
FG
M901
DRUM
MOTOR
VH+
FE(X)
Hw2
11
VH-
10
FE(Y)
SP2(Y)
GND
SP2(X)
GND
GND
SP1(Y)
GND
SP1(X)
10
GND
FG/PG
FG
COM
PG
FG-PG_COM
1
LM(-)
LM(+)
HARNESS
MODE
SWITCH
S001
REC PROOF
S002
C.C.LOCK
H001,002
SREEL SENSOR
TREEL SENSOR
FP-301
FP-302
FLEXIBLE
FLEXIBLE
TAPE LED
Q002
TAPE END
M2000 MECHANISM DECK
N
16
4-5
4-6
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(Measuring conditions voltage and waveform)
(For printed wiring boards)

b: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Through hole is omitted.
Circled numbers refer to waveforms.
There are few cases that the part printed on diagram isnt
mounted in this model.
Chip parts.
Transistor
Diode
C
65 4
45 6
12 3
32 1
32 1
54 3
Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of
pattern box. They are reference values and reference waveforms. *
(VOM of DC 10 M input impedance is used.).
Voltage values change depending upon input impedance of VOM
used.) *
1. Connection
Pattern box
(For schematic diagrams)

All capacitors are in mF unless otherwise noted. pF : m mF. 50V
or less are not indicated except for electrolytics and tantalums.
Chip resistors are 1/10W unless otherwise noted.
kW=1000W, MW=1000kW.
Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat.
Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1.5 m
Front of the lens
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
2. Adjust the distance so that the output waveform of Fig. a and
the Fig. b can be obtain.
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
White
Magenta
Red
Blue
Yellow
A B
Cyan
Green
Constants of resistors, capacitors, ICs and etc with XX indicate

that they are not used.
In such cases, the unused circuits may be indicated.
All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
Signal name
XEDIT EDIT PB/XREC PB/REC
2 : non flammable resistor
1 : fusible resistor
C : panel designation
A : B+ Line *
B : B Line *
J
: IN/OUT direction of (+,) B LINE. *
C : adjustment for repair. *
Circled numbers refer to waveforms. *
* Indicated by the color red.
A=B
B A
Fig. a (Video output terminal output waveform)
Note :
Les composants identifis par
une marque 0 sont critiques
pour la scurit.
Ne les remplacer que par une
pice portant le numro spcifi.
Yellow
Cyan
Green
White
Magenta
Red
Blue
Electron beam
scanned frame
CRT picture frame
Fig.b (Picture on monitor TV)

When indicating parts by reference number, pleas include
the board name.
4-8
For Schematic Diagram

Refer to page 4-103 for waveforms.
1
CD-292 BOARD
CD-315 BOARD
(DCR-TRV230/TRV330)
(DCR-TRV530)
CCD IMAGER
-REF.NO.:10000 SERIESXX MARK:NO MOUNT
GND
C508
XX
CH
GND
A_4.75V
FB5501
0uH
12
11
10
L502
100uH
Y/CHROMA
C502
10u
20V
TA
B
REC
C503
XX
B
PB
G
16
GND
9
Q501
2SC4178-F13F14-T1
BUFFER
C510
XX
B
C509
0.1u
F
C507
33u 10V
TA B
C511
0.01u
B
2012
VIDEO SIGNAL
R9.5/P0
13
R503
0
SIGNAL PATH
R-0.3/P0
14
FB5502
0uH
CHROMA
4
VDD
NC
GND
CCD_OUT
NC
R506
100k
SUB
CAM-7.5
R7.6
/P0
R-0.3/P0
VSHT
V1
CAM_15V
VL
(SEE PAGE 4-15)
CCD IMAGER
R-7.8
/P0
R-7.1/P0
V2
GND
THROUGH THE
FP-265 FLEXIBLE
RG
R12.9
/P0
10
H2
V3
11
H1
V4
RG
TO
VC-254 BOARD(1/18)
CN1501
IC501
H1
12
R1.6
/P0
13
GND
R1.4
/P0
14
V1
ICX219AKA-43
15
V2
H2
16
V3
IC501
V4
R-7.1/P0
16P
D001
MA111-(K8).S0
NO MARK:REC/PB MODE
R :REC MODE
CN501
P :PB MODE
LND501
CCD_OUT
Ref. No. CD-292, CD-315 Boards; 10,000 Series
R14.9
/P0
CD-292 (CCD IMAGER) PRINTED WIRING BOARD (DCR-TRV230/TRV330)

CD-315 (CCD IMAGER) PRINTED WIRING BOARD (DCR-TRV530)
R505
1M
R14.9/0
R9.5/P0
R8.8/P0
R501
56
R504
3900
Precautions Upon Replacing CCD imager

The CD-292/315 board mounted as a repair part is not equipped
with a CCD imager.
When replacing this board, remove the CCD imager from the
old one and mount it onto the new one.
If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
H
For printed wiring boards
Refer to page 4-107 for parts location.
CD-292, CD-315 boards consists of multiple layers.
However, only the sides (layers) A and B are shown.
Chip parts
LB-068 (TRV230/TRV330)
LB-070 (TRV530)
(EVF BACK LIGHT)
CF-079 (TRV230/TRV330)
CF-080 (TRV530)
CD-292 (TRV230/TRV330)
CD-315 (TRV530)
(CCD IMAGER)
PD-138 (TRV230/TRV330)
PD-139 (TRV530)
Transistor
C
There are a few cases that the part printed on

this diagram isnt mounted in this model.
4-9
4-10
CCD IMAGER
CD-292/CD-315
VC-254 (CAMERA/STD8/Hi8/PB PROCESS, DV SIGNAL, PB RF AMP, VIDEO IN/OUT, AD CONVERTER, MODE/CAMERA/MECHA CONTROL,
LASER LINK, DRUM CAPSTAN DRIVE, AUDIO PROCESS, MIC, DC/DC CONVERTER) PRINTED WIRING BOARD
Ref. No. VC-254 Board; 10,000 Series
CAMERA/PB PROCESS, PB/REC AMP, ANALOG/DIGITAL PROCESS, VIDEO/AUDIO PROCESS, POWER SUPPLY
VC-254
4-12
For printed wiring board

Refer to pages 4-107 to 109 for parts location.
VC-254 board consists of multiple layers. However, only
the sides (layers) A and B are shown.
Chip parts
Transistor
C
Diode
65 4
12 3

SI-028 (TRV230/TRV330)
SI-029 (TRV530)
LASER LINK
FP-283
FP-275
(PANEL REVERSE)
(SWITCH)
VC-254
DC/DC CONVERTER
FP-282
(FOCUS)
4-13
CAMERA/PB PROCESS, PB/REC AMP, ANALOG/DIGITAL PROCESS, VIDEO/AUDIO PROCESS, POWER SUPPLY
VC-254

Refer to page 4-11 for printed wiring board.
10
11
13
CAM_15V
VC-254 BOARD(1/18)
A
12
REG_GND
CAMERA PROCESS(CAM BLOCK)
A_2.8V
-REF.NO.: 10000 SERIESXX MARK:NO MOUNT
TO(18/18)
TO(2/18)
SPCK
TO(2/18,5/18,8/18,
17/18(CN1104))
FRQ_TUNE
TO(12/18)
CAM_DD_ON
TO(10/18)
TO(2/18)
TO(2/18,11/18)
TO(2/18,11/18)
TO(11/18)
A_4.75V
CAM_-7.5V
D_2.8V
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
VCK
ADCK
R1508
XX
GND
13
CCD_OUT
14
GND
15
A_4.75V
16
R0.6/
P0
C1505
1u
F
R1501
0
R1.6/P0
R1.4/P0
R1502
0
C1501
22p
CH
R2.3/P0
OSCI
VSS1
PBLK
OSCO
CLPDM
VSS2
1.4
CK
1.4
FB1505
1.3
TEST
1.5
CHCK
XRS
AHD
TIMING GENERATOR
VDD6
IC1501
VDD3
DSGAT
CXD2444R-T4
XV1
VDD4
H1
RST
SEN
H2
SSI
VSS4
NC
SSK
CK_CONT1
R0/P0
CK_CONT2
R2.7/P0
SYS_V
R2.5/P2.8
2.8
R2.9/P0
0.1
2.8
XRST_KINUTA
2.1
XCS_KINUTA
R0.2/P0.7
XVC_SCK
VC_SO
VC_SO
2.5
XCS_KINUTA
XVC_SCK
XRST_KINUTA
VC_SI
CH_SO
XCH_SCK
XCS_CH
XVC_SCK
VC_SO
XCS_KINUTA
XRST_KINUTA
VC_SI
CH_SO
XCH_SCK
XCS_CH
25 26 27 28 29 30 31 32 33 34 35 36
R-7.6/P0
R-0.3/P0
AVD
IC1501
C1506
4.7u
20V
R1503
100k
CKCONT1
CKCONT2
RG
C1503
22p
CH
37 38 39 40 41 42 43 44 45 46 47 48
12
ID
R2.8/P0
VGAT
11
VSHT
VSS3
R1.8/P0
XSHP
R2.0/P0
XSHD
ID
SSO
XSHP
VDD2
1.4
C1504
1u
F
C1511
0.1u
B
2012
R1509
XX
VSHT
AVD
AHD
XSHD
C1502
0.001u
B
10
CAM-7.5
XSG1
R2.7/P0
2
2.6
CAM_15V
R1512
470k
2.8
R2.8/P0
NC
R-7.2/P0
XSHT
V4
H2
R-7.1/P0
(SEE PAGE
4-10)
V1
GND
VM
H1
R-7.1/P0
VL
RG
C1512
X1501 0.001u
B
27MHz
V3
2.8
GND
C1510
XX
C1509
0.001u
B
R1523
220
V2
VDD1
12 11 10
SYSCK
V1
V3
VICK(CL)
V2
V4
R-0.3/P0
V1
R14.9/P0
VH
TO
CD-292/315 BOARD
CN501
(THROUGH THE FP-265
FLEXIBLE)
V2
V3
1.5
16P
V4
R1505
100
R1506
100
24 23 22 21 20 19 18 17 16 15 14 13
CN1501
R1504
100
FB1501
1.5
C1507
10u
4V
FB1503
FB1502
D1501
1T379-01-T8A
V_STOP
VC_SI
XV1
VSHT
V4
V3
V1
V2
XSG1
CLP1
PBLK
SIGNAL PATH
AD1
AD3
AD2
R1.1/P2.8
AD4
R1.1/P0
R1.1/P2.8
AD5
AD6
R1.1/P0.1
AD7
R1.2/P0
R1.1/P2.8
AD8
R1.2/P2.8
TEST
D0
AVSS
CLPOB
AVSS
IC1502
VSP2200Y-1/2K
XSHP
AVDD
XSHD
REFN
REFP
CLPDM
AVSS
CHROMA
LINE
AVDD
AVDD
CMLEVEL
1.5
R1.9/P0.7
25 26 27 28 29 30 31 32 33 34 35 36
37 38 39 40 41 42 43 44 45 46 47 48
D1
D2
D3
D4
D5
D6
D7
D8
PBLK
2.8
C1525
1u
B
S/H,AGC,A/D CONVERTER
DVDD
AVSS
2.8
IC1502
HDRST
L-
R2.7/P0
DVDD
R2.0/P0
LatchSelect
2.8
R1.8/P0
XSHD
2.8
CAMERA PROCESS
VC-254 (1/18)
C1517
120p
C1516
0.1u
C1513
0.47u
C1514
56p
R1521
0
4-15
AD9
AD6
CH_SO
AD5
XCS_CH
AD4
2.8
2.4
AD3
AD2
2.8
XRST_KINUTA
AD1
10
TO(2/18)
PB_C_RF
11
TO(9/18)
TAKO_Y_OUT
12
TO(7/18)
AD10
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
AD1
2.8
1.3
1.8
1.5
C1523
0.1u
B
C1521
1u
B
C1522
1u
B
C1520
0.001u
C1518
1u
B
C1515
0.22u
B
16
AD10
XCH_SCK
C1519
0.22u
B
L1501
10UH
AD7
ADCLK
0.5
XSHP
SYSV
CCD IN
DVSS
L2+
2.8
SI
0.9
R2.3/P0
XCE
R1.5/P0
2.8
DRVSS
L1+
2.8
R1520
XX
XSCK
AVDD
R1.5/P1.4
DRVDD
R1.7/P0
C1526
XX
R0.9/P0.7
2.8
C1524
22u
4V
AD8
DVDD
C1508
1u
B
R1.0/P0
12 11 10
24 23 22 21 20 19 18 17 16 15 14 13
R1519
0
FB1504
PB
AD9
R0.2/P0
REC
R0.8/P0
Y/CHROMA
AVSS
D9
CHROMA
AD10
VIDEO SIGNAL
FB1506
4-16

2
3
1
10
12
11
13
14
15
16
17
18
19
20
VC-254 BOARD(2/18)
CAMERA PROCESS,HI8/STD8 PB PROCESS
L2209
10uH

D_2.8V
0uH
FB2202
0uH
D_1.5V
L2202
10uH
XV1
XSG1
AHD
V_STOP
AVD
ID
PBLK
CLP1
ADCK
AD9
AD8
AD10
ID
ID
R2.8/P0
AVD
1.5
R0.1/P0
R2.5/P2.8
R2.7/P0
1.4
R2.3/P0
2.8
R2.7/P2.8
R1.5/P1.4
1.5
2.8
1.5
1.5
2.8
2.8
2.8
1.5
R2245
470
KINUTA_C_OUT
2.8
AD7
C2250
10u
4V
0.1u
R2244
12k
R0.4/P0
C2236
C2244
0.01u
B
AD6
C2240
1u
B
REG_GND
AD5
C2238
1u
B
C2225
XX
C2228
XX
R1.7/P0
C2233
0.01u
B
R1.3/P2.8
10uH
R1.3/P0
L2204
AD4
C2232
10u
4V
L2208
10uH
A_4.75V
AD3
R2226
0
R1.1/P2.8
L2201
XX
R1.1/P0
R2227
0
AD2
13 TO(18/18)
FB2203
XX
AD1
R2228
0
L2203
XX
R1.1/P0.1
A_2.8V
0uH
FB2204
R1.1/P2.7
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
FB2205
R1.1/P2.2
AVD
AHD
AD1
AD1
216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163
XVC_SCK
VC_SO
VC_SI
XCS_KINUTA
XRST_KINUTA
VC_SI
C2204
0.1u
B
Q2207
UP0460100850
BUFFER
VDDAA3
YMO3
VDDAA2
YMI3
REXT2
CBU2
DVSS6
12
DAO2
YMO4
YMI4
VSSAA2
YMO5
VSSAA1
YMI5
DAO1
CBU1
IO_VDD3
YMO6
REXT1
YMI6
VDDAA1
YMO7
VDDAA0
YMI7
VRBAD
DVSS5
VRTAD
CMO3
VINNAD
CMI3
AD_IN
CMO2
OP_OUT
VSSAA0
C_IN
CMI2
DVDD2
11
CMO1
ATF_IN
CMI1
VREFOP
Y_RF_IN
CMO0
10
CMI0
AVDD
EOR_OUT
AMPO
TESTKP
FC_RST
AD4
AD5
AD5
AD6
2.8
AD6
AD7
AD7
AD8
R1.4/P2.8
2.8
10 TO(1/18)
AD8
AD9
IRIS_COM
AD9
AD10
AD10
0
V_STOP
V_STOP
PBLK
PBLK
XSG1
XSG1
XV1
0
XV1
EN1
R2.4/P2.8
DIR1B
R2.4/P2.8
DIR1A
R0/P2.8
DIR0A
R1.4/P2.8
DIR0B
CLP1
ADCK
IRIS_COM
R2.6/P2.8
IFI_HD
C2243
1u B
1608
IFI_OE
DIR1B
DIR1A
DIR1A
EN0
DIR0B
DIR0A
ZM_RST
IFI_Y0
23 TO(3/18)
DIR0B
DIR0A
R1.1/P0
17/18(CN1104))
EN1
DIR1B
IFI_VD
3 TO(1/18,5/18,8/18,
IRIS_COM
EN1
EN0
R1.3/P0.1
2 TO(1/18)
VCK
SPCK
EN0
2.8
2.8
CLP1
ADCK
ZM_RST
FC_RST
FC_RST
IFI_Y0
R1.1/P0
IFI_Y1
IFI_Y0
IFI_Y1
IFI_Y1
IFI_Y2
1.5
IFI_Y2
IFI_Y3
R1.1/P0
IFI_Y2
IFI_Y3
IFI_Y4
IFI_Y4
IFI_Y5
R1.0/P0
IFI_Y3
IFI_Y5
IFI_Y6
IFI_Y6
20 TO(8/18,
17/18(CN1104))
IFI_Y7
IFI_Y7
IFI_C0
R1.5/P0
IFI_Y4
R1.2/P0
IFI_Y5
IFI_C0
IFI_C1
IFI_C1
IFI_C2
IFI_C2
IFI_C3
IFI_C3
IFI_OE
R0.8/P0
R1.4/P0.1
IFI_Y6
IFI_HD
IFI_Y7
IFI_VD
R1.8/P0
IFI_C3
R1.3/P0
IFI_C2
IFI_OE
IFI_HD
IFI_VD
21 TO(8/18,
17/18(CN1104))
22 TO(8/18,13/18,
17/18(CN1104))
1.5
R1.5/P0
IFI_C1
R1.4/P0
IFI_C0
IO_VDD2
DVSS4
DVSS3
FECKOUT
RAMTEST
XFEON
FECKIN
MCKCONT
R2.8/P0
ADCKCONT
XRST
XCS
R0.2/P0.7
SI
SO
XSCK
IN_VSS2
R2.8/P0
CSYNC
R0/P2.8
MECHAVD
BCK
IN_VDD2
MECHAFLD
SYSV
ATSMPL
XSGRST
SWP
HSWP
JVDI
DVSS2
MCK
OUT_VDD1
OFSC
TRAPCONT
DOP
PANELSYNC
PANELHD
INN
ZM_RST
VCK
DVDD4
XSG1
DVSS9
VGAT
XV1
AHD
AVD
ID
PBLK
DVSS10
COLOR1
COLOR2
COLOR3
CGCK
COLOR4
YMI2
2.8
AD3
AD4
D2201
KV1870STL
D2202
KV1870STL
2.8
R2255
0
2.1
2.5
2.5
1.4
2.4
2.8
2.8
SIGNAL PATH
VIDEO SIGNAL
CK_CONT1
CK_CONT2
XCS_KINUTA
VC_SO
C2242
1u
CHROMA
Y/CHROMA
REC
C2251
XX
GND
N.C
VC_SI
IN
C2247
1u
B
1.5
1.4
2.7
3.0
OUT
XVC_SCK
R2243 C2234
15k
0.01u
B
R2230
XX
MECHA_VD
1.5
VCC
MECHA_HD
C2231
XX
L2207
3.3uH
R2248 R2256
0
10k
MECHA_FLD
C2230
1500p
B
3.0
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108
R2242
15k
R2222
3300
C2201
0.01u
B
IO_VDD5
YMO2
REXT3
2.8
R2241
XX
3.7
DVDD3
SYS_V
R2219
100
YMI1
IC2201
HG75C012SFL
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162
CBU3
XRST_KINUTA
C2202
10u
6.3V
VC_SO
XRST_KINUTA
DAO3
ATF_SAMPLE
3.1
XCS_KINUTA
VSSAA3
R2240
1M
C2212
1u B
3.1
8 TO(1/18,11/18)
YMO1
SWP_DIR
CK_CONT1
XVC_SCK
VSSAA4
R2216
6800
10k
10k
R2213
5600
3.7
YMO0
YMI0
4.7
SYS_V
CK_CONT2
DVSS7
X1/2_SWP
CK_CONT2
CK_CONT1
R2220
39k
IC2201
JOG_VD
7 TO(1/18,11/18)
SWP_DIR
C2211
4.7u
6.3V
2.8
MEMFLDI
CAMERA SIGNAL PROCESS
DAO4
R2231
0
SYS_V
X1/2_SWP
C2227
0.47u
B
CBU4
VIFLDO
13
R2229
0
SWP_DIR
C2208
390p
CH
R2210
1200
R2215
1k
R2218
470
X1/2_SWP
R2205
ATF_SAMPLE
MECHA_VD
MECHA_FLD
ATF_SAMPLE
R2209
JOG_VD
MECHA_VD
MECHA_FLD
JOG_VD
REXT4
PANELVD
R2221
820
MECHA_HD
VDDAA4
PDET3
3.1
XTBC_V_RST
MECHA_HD
2.8
VDDAA5
C2210
1u
B
VIVDO
MEMVDI
PDET2
C2226
0.01u B
AFC_F0
18 TO(11/18)
R0/P1.4
R0/P1.1
TBC_VD
R0/P1.1
R2223
8200
AFC_F0
MEMHDI
2.8
PB_C_RF
VIHDO
14
REXT5
INP
17 TO(17/18(CN1108))
CBU5
C2235
XX
11 TO(9/18)
C2213
0.01u
B
DAO5
IO_VDD4
15
8bit A/D
R0/P1.1
VSSAA5
DVDD1
R0/P1.1
VSSAA6
PDET1
R0/P1.4
C2229
0.01u
B
C2203
XX
EN0
AFCC
R0/P1.4
DAO6
IN_VDD1
R0/P1.9
DIR0B
OSCI
R0/P0.8
0.1u B
C2223
CBU6
DIR0A
2.8
C2222
0.1u
B
C2224
0.1u
B
REXT6
DIR1A
OSCO
2.8
DIR1B
VDDAA6
EVF_B
EN1
VDDAA7
EVF_G
C2215
1u
B
DVSS8
REXT7
EVF_R
VCKO
CBU7
IN_VSS1
DOP
DAO7
PDVSSA
RF_AGC_OUT
TESTBS
PAVSSA
8
9
16 TO(9/18)
XTECVRST
VSSAA7
PANEL_B
TBCVD
VSSAA8
PANEL_G
54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
AFC_F0_ADJ
IRIS
PANEL_R
15 TO(12/18)
16
RF
TEST
DAO8
PAVDDA
KINUTA_Y_OUT
17
PDVDDA
CBU8
DVSS1
470
R2225
REXT8
MUTE
SENS0
WRHLD
0.1u
SENS1
Y_OUT
C2214
AD2
AD3
C_OUT
VDDAA8
SCAN_PATH
AVSS
R2224
12k
OSD_P_ON
2.8
OSD_R_ON
CLP1
OSD_L_ON
DVSS11
ADCK
DVDD5
ADIN9
ADIN8
ADIN7
ADIN6
ADIN5
ADIN4
ADIN3
ADIN2
ADIN1
ADIN0
PLLENB
XTALIN
CCDCKL
IN_VDD3
PDVSCC
IN_VSS3
XTALOUT
PAVSCC
PAVDCC
PDVDCC
PAVDDB
PDVDDB
VSSA9
PAVSSB
PDVSSB
DAO9
CBU9
TESTDAC
REXT9
VDDAA9
AD2
14 TO(7/18)
6 TO(1/18)
AHD
PB
IC2202
XX
NM
R2247
1k
R2206
100k
AFM_FSC
19 TO(15/18)
N
16
4-17
4-18
CAMERA PROCESS, Hi8/STD8 PB PROCESS

VC-254 (2/18)

11
10
VC-254 BOARD(3/18)
A
IRIS/FOCUS/ZOOM DRIVE(LD BLOCK)

R1567 2200

NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
C1562
0.22u
B
R1568
15k
R1565
470k
R1570
470k
C1560
470p
B
R1560
10
HALL_REF
HALL_GAIN
R1572
1k
C1564
0.001u
B
R1571
1k
24 TO(12/18)
HALL_OFFSET
C1570
0.01u
B
L1553
10uH
IN1-
OUT1
1.2
IN1+
0.9
Vcc
0.9
IN2+
4.7
IN2-
C1554
4700p
B
C1571
10u
6.3V
C1567
XX
OUT2
C1552
0.01u B
C1556
10u
4V
D1551
MA111-(K8).S0
R1.1/
P0.2
0.9
0.9
A_4.75V
24
IRIS_HALL(+)
23
IRIS_BIAS(+)
22
IRIS_HALL(-)
21
IRIS_BIAS(-)
20
IRIS_DRIVE(-)
19
TEMP
18
TEMP
17
ZM_SENSE_VCC
16
GND
15
FC_SENSE_VCC
14
0.1
R1563
10k
C1565
0.47u
B
R1569
22k
OUT4
C1566
0.01u
B
1k
R1573
330
R1575
R1.0/P0.2
R1576
10k
0.1
R1562
2200
C1558
0.1u
B
IN4-
IN4+
GND
10 11 12 13 14
0.7
R1566
470k
R1564
220k
24P
IRIS_DRIVE(+)
C1559
0.1u
B
R1556
1k
25 TO(18/18)
IRIS DRIVE,
AMP
0.6
Q1554
2SC4738F-Y/GR(TPL3)
AMP
CN1551
R0.4/
P0
IRIS DRIVE
Q1551
2SC4738F-Y/GR(TPL3)
IN3+
R1.0/
IN3- P0.2
OUT3
8
R1.7/
P2.8
MT_5V (4.75)
REG_GND
IC1552
NJM12902V(TE2)
R1561
1M
D_2.8V
MT_GND
IC1552
C1572
0.1u
B
C1568
2200p R1577
B
47k
R1574
22k
HALL_AD
IRIS_PWM
2.8
L1552
-0.3
R1555
68k
2.8
R1557
68k
ZOOM_B
ZOOM_XB
ZOOM_XA
IR_SWITCH
IR_SWITCH
FOCUS_A
FOCUS_B
FOCUS_XB
FOCUS_XA
ZM_RST
LENS_TEMP_AD
ZM_RST
FC_RST
IRIS_COM
R1552 1k
DIR1B
IC1553
EN1
DIR1A
ZOOM/FOCUS DRIVE
2..8
DIR0B
R0.4/
P2.8
10
ZOOM_A
FC_RST
L1551
10uH
11
0.2
N.C.
FC_RST_LED
0.1
12
4.9
13
ZM_SENSE_OUT
0.1
FC_SENSE_OUT
0.1
ZOOM
LENS
BLOCK
26 TO(11/18)
LENS_FILTER_ON_SW
2.8
-0.3
10uH
ZM_RST_LED
C1569
1u
B
Q1555
UP04116008S0
FOCUS/ZOOM SENSE SW
EN0
DIR0A
IN3
EN2
VM4
R0.7/P2.8
IN1
8
C1563
47u
6.3V
10 11 12
0
OUT4A
7
C1561
0.01u
B
EN1
R2.6/P2.8
IN2
PGND
6
IN4
R0.4/P2.8
EN3
EN4
OUT3A
5
4.9
OUT2A
4
0.2
PGND
3
0.1
OUT 1A
2
0.1
1
0.1
4.9
ZOOM LENS BLOCK is replaced as a block

So that its SCHEMATIC DIAGRAM and
PRINTED WIRING BOARD are omitted.
VM1
IC1553
UPD16877MA-6A5-E2
PGND
OUT4B
OUT3B
VM23
OUT2B
D1553
XX
PGND
VDD
D1552
XX
OUT1B
24 23 22 21 20 19 18 17 16 15 14 13
16
R1551
47k
C1551
XX
IRIS/FOCUS/ZOOM DRIVE
VC-254 (3/18)
4-19
4-20
23 TO(2/18)

2
3
1
VC-254 BOARD(4/18)
DV SIGNAL PROCESS(JC BLOCK)
11
10
12
14
13
15
16
17
18

27 TO(6/18)
RF_1.9V
D_1.9V
FB3303
0uH
MCDA0
A_2.8V
FB3307
0uH
MCCE
C3319
0.001u
B
D3302
KV1870STL
2.8
1.3
2.8
1.3
1.3
2.8
C3321
0.01u
MCDA5
DRP
XDVCN
SWP
LIP_SLEEP
ALE
LIP_SLEEP
LPS
OFR
MCHA0
OFR
XRST_LINK
MCHA1
XRST_LINK
XRST_PHY
MCDA0
XRST_PHY
VREF
MCDA1
TRRV
MCDA2
TRRV
SCOD_WINDOW
MCDA3
XCS_SFD
MCDA4
XCS_SFD
XCS_VFD
MCDA5
XCS_VFD
31 TO(13/18)
MCDA6
MCDA7
VSP_SI
SCOD_WINDOW
VSP_SO
VSP_SO
XVSP_SCK
XRST_VSP
XVSP_SCK
R3375 10k
IR_FSC
LINE_OUT_V
R3376
1k
32 TO(12/18)
XRST_VSP
OSDHD
OSDL
OSDP
AFCK
(CN1104))
COL3
AFCK
XWEN_FROM_L
34 TO(17/18
(CN1104))
XWEN_FROM_L
SSS_FROM_L
C3306
0.01u
B
COL2
VFO_VD
VFO_OE
VFO_Y0
VFO_Y1
(CN1104))
VFO_Y2
VFO_Y3
VFO_Y4
VFO_Y5
VFO_Y6
VFO_Y7
1.4
R2.4/P2.3
R2.2/P2.1
R2.2/P2.1
R2.4/P1.6
R2.2/P1.5
R1.4/P1.0
R1.4/P0.9
1.5
R1.2/P1.7
R1.8/P1.3
R0.3/P0.1
0
2.8
0
2.8
2.6
0
0
0.1
0
0
2.8
COL1
35 TO(17/18
1.4
SSS_FROM_L
VFO_HD
2.8
1.5
OSDR
33 TO(8/18,17/18
2.8
MCCE
LPS
VSP_SI
COL0
VFO_HD
VFO_VD
0
0
2.8
AFCK
VFO_OE
1.5
VFO_Y0
VFO_Y1
R1.1/P1.0
VFI_Y0
VFO_Y0
VFO_Y2
VFO_Y3
VFO_Y1
VFO_Y2
VFI_Y0
VFI_Y0
R0/P1.0
R1.1/P1.0
VFI_Y3
VFO_Y3
R0/P1.1
VFO_Y4
R0/P1.8
1.8
VFI_Y4
VFI_Y1
R0/P1.0
R1.1/P1.0
VFI_Y2
VFO_Y6
VFO_Y7
R0/P1.0
R1.1/P1.0
VFI_Y1
VFO_Y4
VFO_Y5
VFI_Y1
VFI_Y2
1.5
VFI_Y2
VFI_Y3
VFI_Y3
VFI_Y4
VFI_Y4
R1.2/P1.1
VFI_Y5
VFO_Y5
VFI_Y5
R0/P1.1
VFI_Y5
VFI_Y6
VFI_Y6
R1.0/P0.9
VFI_Y6
VFO_Y6
VFI_Y7
R0/P0.9
VFI_Y7
36 TO(17/18
(CN1104))
VFI_C0
R1.1/P1.3
VFI_Y7
VFO_Y7
VFI_C0
VFI_C1
LIP_SLEEP
LPS
OFR
LBUS0
R0/P1.2
VFI_C1
LVUS0
LBUS1
XSWE
MSCSS
WRX
25
RDX
SSS
24
DPVD
DPHD
DRP
SWP
HVSS2
ALE
HVDD2
MCCE
LVSS2
MCHA0
LVDD2
MCHA1
MVDD2
RECCK
MCDA0
MCDA1
MVSS2
MCDA2
RECDT
MCDA3
RECA2
RECA1
MCDA4
MCDA5
SWPS
MCDA6
CTRL0
MCDA7
CTRL1
ALLPS
SCWIN
PLLMSK
XRST
IC3301
F358
OSDVD
PLLSW
ADDT5
DV SIGNAL PROCESS
OSDHD
ADDT4
RVDD4
ADDT3
RVSS4
ADDT2
OSDR
ADDT1
OSDL
ADDT0
OSDP
MVDD1
COL3
PBCK
IC3301
CAIN
COL2
MVSS1
HVDD4
ATF
HVSS4
AVDD3
COL1
IREFP
COL0
AVSS3
AFCKI
PYOUT
RVDD5
DVDD3
RVSS5
PCROUT
DVSS3
YI0
YO0
PCBOUT
AVDD2
YI1
YO1
IREFE
YI2
AVSS2
YO2
EYOUT
YI3
DVDD2
YO3
ECROUT
DVSS2
YI4
YO4
ECBOUT
AVDD1
RVDD6
RVSS6
IREFC
YI5
AVSS1
YO5
COUT
DVDD1
YI6
YO6
IREFY
23
YI7
DVSS1
YO7
YOUT
XWEN_FROM_L
2.8
LVUS1
LBUS2
SSS_FROM_L
LVUS2
LBUS3
LVUS3
DIR
2.8
XACC
XENA
XENA
FRL
2.8
FRL
FCLR
FCLR
ADAI2
1.5
R3313
1.9
R0.8/P0
ADAI2
ADAO2
RECCK
RECA2
R1.9/P0
RECA1
R1.9/P0
SFD_FCK
SFD_LRCK
RECDT
SFD_LRCK
SFD_BCK
DATA_TO_SFD
DATA_FROM_SFD
SW_PS
DATA_FROM_SFD
SFD_LRCK
SFD_LRCK
SFD_BCK
PLLMSK
PLLSW
TCK
TMS
42 TO(8/18,17/18(CN1104))
TMS
TD_3-4
TD_3-4
TDO
TDO
ADDT5
R0.1/P1.1
ADDT4
R0.1/P1.1
ADDT3
PANEL_XHD
R0.1/P1.1
ADDT2
ATF_ERR
R0.1/P1.1
ADDT1
R0.1/P1.1
ADDT0
PANEL_XVD
43 TO(8/18)
44 TO(17/18(CN1108))
45 TO(5/18,17/18(CN1117))
38 TO(13/18)
SW_PS
L3306
10uH
R0.1/P1.1
41 TO(17/18(CN1104))
SFD_BCK
TCK
ALL_PS
40 TO(15/18)
SFD_BCK
DATA_TO_SFD
R0/P0
39 TO(17/18(CN1104))
ADAO2
SFD_FCK
50 TO(5/18)
DIR
XACC
C3317
0.01u
B
2.6
SW_PS
ALL_PS
ALL_PS
1.9
RECA2
PBCK
RECA2
C3323
0.01u B
R0/P1.0
RECA1
RECA1
RECCK
1.4
R3315
3300
2.8
RECDT
RECDT
Q3310_VC
C3352
XX
1.6
RECCK
C3327 22u 4V
PLLSW
C3328
0.01u
B
PLLSW
PLLMSK
C3339 XX B
PYOUT
2.8
ADDT4
ADDT3
R3396
ADDT5
ADDT4
0.3
PCROUT
ADDT3
ADDT2
0.3
ADDT2
ADDT1
PCBOUT
0.3
ADDT1
ADDT0
R3316 3300
ADDT0
PBCK
2.8
46 TO(6/18)
PLLMSK
ADDT5
PBCK
0
51
C3340 XX B
TO(5/18)
EYOUT
0
2.8
R3397
ECROUT
R0/P0.1
ECBOUT
0
R3321 3300
2.8
C3341
1u B
R1.6/P1.5
R3398 0
R3338
1k
0.5%
MCHA1
XRST_VSP
XRST_PNY
OFR
R3327 XX
RDX
MCHA0
SCOD_WINDOW
XDVCN
LPS
R3332 XX
MCHA0
MCHA1
XRST_LINK
XRST_PNY
R3309
0
WRX
MCDA7
2.7
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108
XCS_SFD
MCDA7
216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163
MCDA6
MCDA6
VREF
ALE
XDVCX
MCDA5
XDVCN
WRX
XRST_LINK
PVDD2
PVSS2
PCOR
OVDD2
OSCIN
OVSS2
OSCOUT
TCK
PLLTES
TMS
TDI
TDO
TEST
SCAN
LVDD3
LVSS3
BCKO
LRCKI
LRCKO
BCKI
FCKO
OCKO
OCKI
ADAI1
ADAO1
ADAI2
ADAO2
ECKI
OVDD3
XOI
XOO
OVSS3
LCKO
LBUS0
LBUS1
FRL
LBUS2
LBUS3
FCLR
DIR
XENA
XACC
VREF
FRRV
TRRV
HVDD3
HVSS3
TRRT
LVDD4
LVSS4
MSI
MSO
MCDA4
MCDA4
MSSCK
MSCSV
MCDA3
MCDA3
RDX
ALE
48 TO(5/18)
MCCE
162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109
MCDA2
30 TO(13/18)
MCDA7
WRX
C3348
0.01u
B
C3346
0.01u
B
MCDA1
MCDA2
MCDA6
MCCE
C3320 10u 4V
2.8
0.5
1.5
0.9
1.1
0.7
0.7
0.7
2.8
1.3
1.3
0.8
2.8
2.8
2.8
2.8
2.7
2.8
2.8
0.6
1.4
2.8
1.4
1.5
2.5
MCDA1
0.3
MCDA0
MCDA5
MCDA7
C3318
0.01u
B
LIP_SLEEP
2.7
2.6
MCDA0
MCDA4
MCDA6
MCCE
MCDA3
MCDA5
RDX
C3314
0.001u
B
TCK
TDO
TMS
C3322
0.47u
B
L3305 10uH
R3310
10k
RB705D-T146
D3301
SFD_LRCK
R3320
2200
R3311
10k
TD_3-4
VREF
FRRV
TRRV
TRRT
R3307
XX
1.4
ALE
VSP_SI
ALE
C3301
0.1u
B
VSP_SO
DRP
XCS_VFD
DRP
XVSP_SCK
TRRT
R3322
100
R3312
270
L3303
0.56uH
1.4
FRRV
TRRT
SFD_FCK
RDX
FRRV
SFD_BCK
RDX
R3386
0
DATA_FROM_SFD
LBUS0
LBUS1
LBUS2
LBUS3
DIR
FRL
FCLR
WRX
WRX
XENA
SWP
C3312
0.01u
B
C3310
0.01u
B
C3313
0.001u
X3301 24.576MHz
17/18(CN1108))
SWP
XACC
REG_GND
29 TO(13/18,
C3308
10p
CH
C3307
10p
CH
C3305
0.1u
B
ADAI2
C3302
0.1u
B
MCDA4
ADAO2
D_1.5V
49 TO(5/18)
MCDA2
MCDA3
R3385
0
DATA_TO_SFD
C3303
0.1u
B
47 TO(5/18)
LCKO
MCDA1
MCDA2
28 TO(18/18)
RF_1.9V
MCDA0
MCDA1
D_2.8V
19
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
CONT
R3395 0
0.4
2.8
R3317
4700
R0/P1.6
C3342 1u B
YOUT
0.4
VFI_C2
SIGNAL PATH
PVSS1
PVDD1
TRCKI
TRCKO
TSCKO
SPCKI
HVSS5
OVSS1
POI
POO
PCO
OVDD1
LVSS1
TESTD0
LVDD1
TESTD1
TESTD2
TESTD3
TESTD4
TESTD5
TESTD6
RVSS3
RVSS2
RVSS1
RVDD3
RVDD2
RVDD1
TESTD7
TESTD8
OEO
OEI
VO
VI
HO
HI
CI4
CO7
CO3
CI7
CI3
CO6
CO2
CI6
CI2
CO5
CO1
CI5
CI1
CO4
CO0
VFIO_C5
CI0
VFIO_C4
HVSS1
HVDD1
VFI_C3
VFI_C3
VFIO_C4
TESTD9
VFI_C2
REC
VFIO_C5
VFIO_C6
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
VFI_HD
VFI_HD
1.5
2.8
1.2
1.2
1.5
1.3
1.2
2.8
R3325
47
C3315
0.001u
B
R3326
0
C3309
0.01u
B
C3343
0.01u
B
C3316
0.001u B
16
D3304
KV1870STL
ICLK
OSDL
C3324
0.047u
B
C3325
0.001u
B
TO(5/18)
PB
SIGNAL PATH
VIDEO SIGNAL
OSDR
COL3
CHROMA
COL3
COL2
COL2
COL1
COL1
COL0
OSDP
53
TO(5/18)
Y/CHROMA
AUDIO
SIGNAL
REC
PB
OSDP
LINE_OUT_V
OSDHD
52
OSDL
OSDR
COL0
RB705D-T146
D3303
C3345
0.01u B
C3326
2.2u
B
R3323
330
R3324
4700
L3304
1.8uH
VFI_OE
VFO_OE
VFI_VD
VFO_VD
VFO_HD
VFI_HD
R0/P1.4
R0/P1.3
VFIO_C7
R0/P1.2
VFIO_C6
R0/P1.3
VFI_C3
VFI_C2
C3311
0.01u
B
R3319 R3318
10k
10k
VFI_C1
VFI_OE
VFIO_C4
VFI_OE
VFI_C0
37
TO(13/18,17/18
(CN1104))
VFI_VD
VFIO_C5
VFI_VD
2.8
1.5
1.4
2.8
2.8
2.8
2.8
2.6
R1.4/
P1.5
VFIO_C7
R1.2/
P1.4
1.3
R1.3/
P1.2
VFIO_C7
REC/PB
Ref.signal
VFIO_C6
LINE_OUT_V
OSDHD
SPCK
4-21
4-22
DV SIGNAL PROCESS-1
VC-254 (4/18)

Refer to page 4-11 for VC-254 printed wiring board.
Refer to page 4-53 for printed wiring board of FP-272 flexible.
10
VC-254 BOARD(5/18)
FB3304
IC3303_VDD
14
15
16
C3331
10u
4V
60 TO(18/18)
XRST_LINK
1.9
R3359
XX
C3329
0.01u
B
ALE
R3352
0
RDX
WRX
2.8
MCCE
2.8
2.4
MCDA0
MCDA1
MCDA2
MCDA3
MCDA4
2.8
1.4
MCDA5
MCDA7
2.8
DIR
XACC
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
MCDA6
REG_GND
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
50 TO(4/18)
DIR
XACC
XENA
FRL
FCLR
52 TO(4/18)
LBUS2
LBUS3
DIR
XACC
XENA
VDD2
ALE
XINT
XRW
XCS
XRD
VSS
VDD
R1.4/P0.8
DA3
R1.3/P1.0
DA2
R2.2/P1.5
DA1
R2.4/P1.5
DA0
DA4
VSS
R0.3/P0.2
DA7
R1.8/P1.3
DA6
R1.3/P1.7
DA5
XDIR
XRESETL
10 11 12 13 14 15 16 17 18 19 20
9
R3366 XX
1.2
R3364
12k
R3361
0.1 12k 0.5% 0.5%
0
TPA
NTPA
TPB
TPB
NTPB
NTPB
REG_GND
REG_GND
REG_GND
LANC_SIG
XLANC_JACK_IN
10
LANC_DC
AVD3
TEST5
AVS
TEST6
R3367
56
R3365
0 5%
R3368
56
2.8
R3362 0
R3363
XX
C3337
1u
B
1608
R3370
56
R3369
5100
0.5%
R3371
XX
R3372
56
C3338
220p
CH
C3333
0.01u
B
R3339
XX
R3354
XX
R3355 R3357
XX
XX
R3331
4700
54 TO(10/18)
C3336
XX
R3343
4700
R3389
XX
0.8
PCBOUT
R3328
1200
0.5%
R3334
1200
0.5%
R3340
1200
0.5%
0.3
R3391
XX
Q3306
2SA1774HT2L
0.3
0.3
Q3310
UP04401008S0
BUFFER
EVF_G/BW_Y
R3387
XX
KEY_AD5
18
PANEL_R
17
PANEL_G
16
PANEL_B
PANEL_XHD
15
PANEL_XHD
PANEL_XVD
14
PANEL_XVD
13
HI_SO
XCS_LCD
12
XCS_LCD
XHI_SCK
11
XHI_SCK
HI_SO
10
REG_GND
REG_GND
REG_GND
TO
PD-139 BOARD(2/2) CN5701
(DCR-TRVTRV530)
(SEE PAGE 4-98)
55 TO(17/18(CN1117))
R3388
XX
62 TO(10/18)
EYOUT
EVF_R
NOT USE
63
EVF_B
R3341
XX
R3335
XX
R3356
2200
1.0
R3360
2200
ECBOUT
Q3311
XX
NM
64 TO(18/18)
EP_2.8V
PANEL_2.8V
PANEL_4.75V
PANEL_4.75V
EP_13.3V
PANEL_13.3V
PANEL_-15.3V
BL_CONT
BL_CONT
BL_REG
BL_REG
BL_GND
BL_GND
SE_GND
PANEL_-15.3V
0.4
R3351
270
Q3305
XX
NM
56 TO(7/18)
TO(8/18,10/18,
11/18,13/18,
17/18(CN1117))
Q3309
UP04401008S0
BUFFER
0.4
COUT
R3392
XX
CAIN_Y_OUT
1.0
CAIN_C_OUT
R3394
0
ECROUT
19
KEY_AD5
45 TO(4/18)
51 TO(4/18)
R3329
R3393 XX
XX
XSYS_RST
0.8
0.8
PCROUT
65 TO(18/18)
R3358
220
YOUT
LINE_OUT_V
57 TO(11/18)
SPCK
0
COL2
0
COL1
0
COL0
2.8
LINE_OUT_V
2.6
OSDHD
IC3302
16
10
7
CMDCT
VBLA
VC2
VDD
VC1
XPCL
VC0
DATA
XVSYNC
XCS
XHSYNC
XCLK
IC3302
MB90099PFV-G-108-BND-ER
17/18(CN1104))
OSC
OSC
1.5
BLKB
VC3
C3334
0.01u
B
XSYS_RST
3.0
5
R0.1/P0
OSDP
3 TO(1/18,2/18,8/18,
EVER_3.0V
58
TO(8/18,10/18,
11/18,13/18,
17/18(CN1117))
SIGNAL PATH
VIDEO SIGNAL
2.8
4
53 TO(4/18)
TEST
2.8
3
0
COL3
NC
GND
OSD_SO
CHROMA
59 TO(10/18,17/18(CN1117))
2.7
Y/CHROMA
REC
OSDR
BLKC
2.8
1
0
OSDL
20 19 18 17 16 15 14 13 12 11
SPCK
XOSD_SCK
XCS_OSD
66 TO(10/18)
PB
CHARACTER GENERATOR
DV SIGNAL PROCESS-2
VC-254 (5/18)
4-23
20P
20
61 TO(10/18)
R3390
XX
PYOUT
CN1120
R3336
4700
LANC
LANC_SIG
Q3310_VC
4-24
AUDIO
SIGNAL
LND202
J201
R3347
XX
R3348
XX
SHASSIS GND
SHASSIS GND
LANC_DC
XLANC_JACK_IN
R3353
XX
R3345
XX
R3333
0
C3335
0.1u
OFR
R3330
XX
R3349
0
R3350
0
R3346
0
LCKO
LPS
49 TO(4/18)
LND201
VDR201
R207
0
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
DV
IN/OUT
R204
470
R205
0
ICLK
R3337
0
4P
1.5
0
AVS
FRL
CN202
TPA
7
2.8
AVD3
TPBIAS
TEST4
10P
NTPA
TEST1
TEST3
CN1114
1
TPBTEST2
FLEXIBLE
LANC,DV IN/OUT
TPB+
TEST0
FCLR
2.8
D202
01BZA8.2(TE85L)
LBUS3
LBUS1
FP-272
2.8
0.1
TPAVDD3
1.9
LBUS2
IFCLEAR
2.8
LBUS1
LBUS0
OFR
TEST7
LBUS0
R1
IC3303
SN104266PN-TEB
LIP_SLEEP
2.8
XRST_PHY
XRST_PHY
XINEN
FR
2.8
2.8
XRST_LINK
TPA+
AVD3
XRST_PHY
2.7
FCLR
OFR
R0
AVD3
VSS
XDVCN
0.8
LPS
AVS
2.8
XI
0
XO
FRL
LIP_SLEEP
VDD2
DV INTERFACE
2.8
2.8
XENA
XDVCN
IC3303
ICLK
VDD3
VSS
XRST_LINK
MCDA7
VSS
VDD3
2.8
OFR
1.2
MCDA6
ID0
AVD3
0
PLLFLT
AVS
MCDA5
PWD
ID1
VSS
ENEC
LPS
2.8
1.9
XDVCN
LIP_SLEEP
2.8
LBUS0
VDD2
MCDA7
LBUS1
MCDA4
XRESETP
ID2
TM0
TM1
MCDA5
MCDA6
MCDA3
CNA
ID3
LPS
48 TO(4/18)
2.8
LBUS2
MCDA2
VSS
VDD2
TMP3
MCDA3
MCDA4
2.8
LBUS3
MCDA1
2.8
1.9
MCDA0
TMP1
TMP2
MCDA2
ALE
MCCE
2.8
MCDA0
MCDA1
RDX
VDD3
VSS
ALE
MCCE
XIACC
RDX
WRX
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
WRX
TMP0
13
L3307
10uH
D_2.8V
DV SIGNAL PROCESS(JC-2 BLOCK)

47 TO(4/18)
12
11
C3332
0.01u
B
TO
PD-138 BOARD(2/2) CN5701
(DCR-TRV 230/TRV330)
(SEE PAGE 4-92)

11
10
12
14
13
15
16
17
VC-254 BOARD(6/18)
DIGITAL8 PB RF AMP(RF(D) BLOCK)
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
RP_4.75V
L3105
220uH
L3103
10uH
L3104
10uH
R3123
22k
Q3111
2SA1774HT2L
R3132
270
L3106
12uH
R3126
22k
R3136
2200
R3.9/
P4.0
C3138
100p
CH
4.6
C3140 R3143
XX
56
C3134
0.1u
B
RP_6.0V
TO(18/18)
R3127
33k
A_2.8V
L3102
10uH
R3124
22k
C3135
100p
CH
R4.2/
P4.6
R4.0/
P4.6
Q3116
2SA1965-S-TL
R3.7/P4.6
R3137
4700
Q3117
UP04601008S0
R1.4/
P2.3
REG_GND
R3133
220
C3139
150p
CH
R3.4/P4.6
C3122
10u
6.3V
C3111
10u
6.3V
C3108
10u
4V
C3136
82p
CH
R2.0/P4.6
67
R4.5/
P4.6
R3138
100
R3144
560
R3115
10k
RECA2
C3107
0.01u
B
C3113
0.01u
B
C3114
47p
CH
RECCK
1.9
R3104
6800
C3104
0.01u
B
RECDT
Q3103
DTC144EHT2L
SWITCH
1.9
RECCK
C3129
XX
C3128
0.01u
B
C3119
47p
CH
XME/MP
R2.8/P2.6
R2.8/P2.6
0.1
R3120
22k
0.5%
R3103
10k
Q3102
2SA1774HT2L
VRB DET
FLYING
ERASE OSC
0.1
Q3118
UP04213008S0
SWITCH
R3121
12k
0.5%
RECA2
R0.4/
P2.6
RECDT
RECA1
RECA1
PLLMSK
ALL_PS
PLLSW
ALL_PS
Q3111,3116,
3117
R3118
13k
0.5%
R3119
27k
0.5%
SW_PS
Q3104
DTC144EHT2L
SWITCH
2.8
R3122
68k
0.5%
22k
REC_CRRT1
SW_PS
REC_CRRT0
RF_1.9V
R3117
TO(4/18)
DRUM_8PB
27
XFE_ON
R1.2/P2.8
R3114
4700
TO(11/18)
XME/MP
TO(11/18)
VC_RF_SWP
72
TO(9/18)
DV_PB_RF
73
TO(14/18)
1.9
1.2
R2.8/P2.6
R2.8/P2.6
2.8
D2L
PBSW_PS
CONT0
20
18
YODD(SP1Y)
XODD(SP1X)
R3130
220
0.5%
GND
GND
R3131
220
0.5%
GND
10 11 12
GND
XEVEN(SP2X)
YO
YEVEN(SP2Y)
XO
D2O
DIO
GND
D2E
CONT1
YE
RECA1
GND
XE
TRW
VCC3
FE(Y)
D1L
GND
GND
GND
FBDP_R
PEAKT_IR
PEAKI_IR
RECI_IR
RECA2
CHSP2
R4.8/
P1.7
R4.6/
P1.7
R4.6/
P1.7
R4.8/
P1.7
R3129
220
0.5%
R4.8/
P1.7
R4.6/
P1.7
R4.6/
P1.7
CHSP1
R3125
220
0.5%
37 38 39 40 41 42 43 44 45 46 47 48
R4.8/
P1.7
Q3107,3109,3119,3120
8mmPB CONT.
ALL_PS
XME/MP
RECCK
R3139
3900
RECDT
Q3109
UP04111008S0
2.8
4.7
2.8
R3140
3900
C3112
470p
B
1.4
C3131
0.01u
B
C3110
0.01u
B
DV_RF_SWP
C3109
0.01u
B
FLYING
ERASE
D1E
GND
GND
GND
R3108
1M
4.7
R0.7/P0
GND
10
11P
21 22
R3.4/P2.1
4.7
XFE_ON
R2.3/P1.3
2.8
R1.9/P0
25 26 27 28 29 30 31 32 33 34 35 36
DRUM_8PB
71
SW_PS
2.8
DV_RF_SWP
XCS_TRF
R1.9/P0
REC/PB HEAD
AMP
IC3103
CXA2072R-T4
PB X OUT
C3117
470p
B
C3133
0.1u
B
IC3102
RF_IN
4.7
R3141
3900
Q3107
2SC4738F-Y/GR(TPL3)
4.7
R3128
10k
0
IC3102
TC7S86FU(TE85R)
RF_MON
TO(17/18
(CN1108))
RECA1
1.4
1.4
70
R1.9/P0
2.8
C3127
0.01u
B
C3105
0.01u
B
RECA2
2.8
AGCTC1
AGC VCC
BUF OUT
BUF VCC
ATF OUT
JSWP
I/O VCC
ATF1
ATF2
ATF3
REC_CRRT0
REC_CRRT1
C3126
0.01u
B
R4.1/P2.4
FE(X)
GND
XL
IC3103
19
11
YL
NC
2.0
R3.4/
P2.3
XCS_TRF
R3110
10k
C3115
B
0.1u
VCC2
PB_IR
CP TC2
CL
PLL GND
FAST ACCESS
AGCTC2
4.7
RECCONT_E
PD HOLD
AGC GND
SI
C3121
0.01u
B
RECCONT_O
REC DATA
R0.9/P0
PLL VCC
2.8
4.7
VDD
R3113
12k
CO
R0/P2.0
CE
R4.1/P2.4
PBYOUT
VIDEO HEAD
CN3101
DRUM_8PB
69
TESTIN
DC_TC2
DC_TC1
1.4
XFE_ON
XSCK
2.8
DRUM_8PB
19
TRF
AD D GND
R2.6/P1.5
DV_RF_SWP
DATA5
1.5
REC_CRRT1
DATA4
S IO GND
TO(13/18)
F VCC
R0/P2.7
IN
IC3101
CXA2071R-T4
XCS
REC_CRRT0
68
DRP_SO
EQ.PLL
A/D CONV.
DATA3
1.5
XCS_TRF
DRP_SO
XDRP_SCK
DATA2
2.7
DRP_SO
XDRP_SCK
IC3101
DATA1
R3109
12k
R0/P2.0
C3124
6800p B
VCC1
1.9
F GND
R0.1/P1.3
R REF2
R0/P0.6
R REF3
R2.3/P1.9
DECUP
C3123
6800p
B
DATA
2.8
DATA0
C3120
0.01u
B
R2.3/
P2.1
GND
XDRP_SCK
CP TC1
M2000 MECHANISM
DECK
24 23 22 21 20 19 18 17 16 15 14 13
5.9
R0.1/P1.1
ADDT5
CLK
AD D VCC
R3111
470
R3107
150k
R0.9/P0
ADDT4
CLK
R0.1/P1.1
R0.9/P0
R0.1/P1.1
ADDT3
VDD
ADDT2
TEST
R0.1/P1.1
ALL_PS
ADDT1
1.9
R0.1/P1.1
36 35 34 33 32 31 30 29 28 27 26 25
4.7
R0.1/P1.1
ADDT0
37 38 39 40 41 42 43 44 45 46 47 48
PBCK
REC XP
R0.1/
P1.0
VRT
AD A GND
C3102
0.01u
B
VRB
12 11 10
TO(4/18)
24 23 22 21 20 19 18 17 16 15 14 13
46
C3116
0.033u
B
AD A VCC
PLLMSK
LOCK MON
R0.4/
P2.6
PLLMSK
2.8
PLLSW
PLLSW
R2.4/P2.1
RECDT
EX-OR GATE
C3137
0.01u
B
0
0
C3142
220p CH
C3143
220p
CH
Q3119
UP04501008S0
0
C3144 CH
220p
0
4.7
0
0
R3142
3900
T_REEL_EVR
C3141
220p
CH
Q3120
UP04501008S0
S_REEL_EVR
SIGNAL PATH
VIDEO SIGNAL
CHROMA
Y/CHROMA
AUDIO
SIGNAL
SIGNAL PATH
REC
16
PB
4-25
REC
REC/PB
PB
Ref.signal
4-26
DIGITAL8 PB RF AMP
VC-254 (6/18)

VC-254 BOARD(7/18)
74 TO(8/18)
4.7
0.1
2.4
DRV_Y_OUT
1.4
Y_INV
4.7
Y_VCC
4.7
C_VCC
0.1
DRV_C_OUT
0
SDC
10 11 12
XVSP_SCK
R3724
1k
A Q3705
2SC4738F-Y/GR(TPL3)
DR_V_OUT
DR_Y_OUT
DR_C_OUT
IR_VIDEO
C3714
10u
6.3V
C3715
0.33u
B
C3716
0.01u
B
G
16
VIDEO IN/OUT
VC-254 (7/18)
4-27
4-28
IR_VIDEO
R3727
1k
1.3
C3728
2.2u
B
R3730
1k
C3733
220u
4V
1.5
C3729
2.2u
B
C3730
0.01u
B
C3731
0.01u
B
C_GND
XCS
XSCK
2.8
SI
2.7
D_VCC
0.7
C_IN4
0.01u
DR_V_OUT
C3732
220u
4V
R3726
10k
C3734
10u
6.3V
C3735
13 14 15 16 17 18 19 20 21 22 23 24
MM_TC2
MM_TC3
4FSC_OUT
XTAL
EXTAL
PLL_VCC
APC_FIL
BGT_OUT
41
2.8
R3722
1k
R3708
1200
CAIN_Y_OUT
CAIN_C_OUT
PLL_GND
49
C_IN1
Q3704
XX
56 TO(5/18)
42
Y_GCA_CONT
D_GND
C3706
0.01u
B
Y_IN4
C_IN3
40
CLAMP_TC2
XCS_TAKO
VSP_SO
0.1
Y_IN3
XVSP_SCK
VSP_SO
XVSP_SCK
1.3
Y_GND
43
IC3701
AN2225FHQ-EB
C3724
0.1u B
80 TO(13/18)
R3707
XX
0.2
V_GND
VSP_SO
PB
AGC_CONT
AUDIO
SIGNAL
REC
R3706
1200 0
1.3
CLAMP_TC1
0
IR_V_OUT
4.7
V_VCC
1.3
DRV_V_OUT
V_INV
LINE IN/OUT,
AGC,ACC
50
Y_IN2
44
C3723
B
Y/CHROMA
AGC_CONT
ACC_CONT
C3702
0.01u
B
79 TO(8/18)
Q3703
2SC4738F-Y/GR(TPL3)
0
0
ACC_CONT
R3715
33
2.3
SYNC_SEP_TC
R3701
4700
Q3702
RN2104F(TPL3)
1.3
45
IC3701
MAIN_GND2
0.01u
XCS_TAKO
2.8
48
Y_IN1
0.1
XCS_TAKO
C3701
0.01u
B
XVIDEO_IN
CHROMA
S_Y_I/O
IR_VIDEO
SDC_IN
VIDEO SIGNAL
C3709
0.033u
B
C3708
B
2.2u
C3704
0.22u
B
C3712
2.2u B
C3707
1u B 1608
C3710
2.2u B
C3705
0.33u
B
Q3702-3705
SWITCH
AUDIO_L_I/O
1.3
AUDIO_R_I/O
C3711
2.2u B
46
MAIN_GND1
MAIN_VCC
R3705
220k
IR
C_IN2
R3702
4700
4.7
9
10
76 TO(15/18)
Q3701
2SC4738F-Y/GR(TPL3)
BUFFER
AV_GND
AUDIO_R_I/O
77 TO(12/18)
SIGNAL PATH
R3712
39
VIDEO_I/O
C3719
0.01u
B
VREF
VIDEO_I/O
47
R3721
22k
0.5%
AGC_VOUT
AV_JACK_IN
78 TO(13/18)
INPUT_Y_OUT
C_GCA_CONT
AUDIO_L_I/O
R3704
100
4.7
R3716
39
ACC_CONT
VDR105
VIDEO_I/O
S_Y_I/O
4
48 47 46 45 44 43 42 41 40 39 38 37
VDR103
L3705
10uH
36 35 34 33 32 31 30 29 28 27 26 25
AGC_CONT
D102
UDZS-TE17-8.2B
(Note)
Note:
CAPACITOR is mounted to the
Location where R110.111 are printed.
R107
0
VDR104
S_GND
S_Y_I/O
R105
0
R110
0.1u
XS_JACK_IN
R104
0
LND102
SHASSIS GND
S_GND
R3717
33
VDR101
S_C_I/O
S_C_I/O
R3714
39
SHASSIS GND
J102
10P
VDR102
D101
UDZS-TE17-8.2B
1
2
3
4
5
7
6
CN1115
R3713
33
R101
0
R108
0
R109
0
S_C_I/O
R102
0
R111
0.1u
(Note)
C3717
1u
B
1608
XS_JACK_IN
S
S
G
AV_JACK_IN
75 TO(10/18)
L3701
10uH
KINUTA_C_OUT
2.8
AUDIO/VIDEO
15
REG_GND
INPUT_C_OUT
LND101
14
TAKO_Y_OUT
KINUTA_Y_OUT
14 TO(2/18)
13
FB3701
0uH
TAKO_C_OUT
12 TO(1/18,
8/18)
S VIDEO
12
11
D_2.8V
FLEXIBLE
J101
10
A_4.75V
FP-270
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
VIDEO IN/OUT
DR_Y_OUT
R3728
1k
R3729
1k
DR_C_OUT
81 TO(18/18)

VC-254 BOARD(8/18)
10

TD_2-3
TD_3-4
2.8
2.5
2.1
2.9
2.4
2.8
TS1
DVDD3
XSCK
SI
SO
XCS
ZCKI
MZSEL
TS2
DVSS3
VERIFY
TMS
TCK
TRST
PSCNTO
RCKSEL
ADATB
CLPVO
ACCVO
DATOP
DABOT
DAVDD
2.8
XPLRST
C3620
0.01u
B
AGCVO
DVSS1
APCVO
DVDD1
DAREF
XACLKE
R1.4/P0.2
AOE
R2.8/P2.7
AVD
R2.6/P2.8
AHD
C3619
0.01u B
DAVSS
OSCSEL
2.8
ACLKO
ACC_CONT
MB87L1241PFV-G-BND-ER
AD8TB
MCSEL
0.1
DVSS2
2.8
DVDD2
R1.0/P0
DCOUT0
R1.0/P0
DCOUT1
R1.0/P0
DCOUT2
R1.0/P0
DCOUT3
R1.0/P0
DCOUT4
0
DCOUT5
0
DCOUT6
0
DCOUT7
2.8
XRST
IC3603
DVSS0
1.5
EXCKI
0.1
0.1
TO(7/18)
AD8TOP
VIDEO A/D CONVERTER
DVDD0
C3618
0.01u
B
AD8VSS
IC3603
VCXOI
C3617
0.01u B
0
AGC_CONT
AD8VDD
OSVSS
0
0
R3622
470
AD8BOT
BCKI
ADAVSS
R0.5/P0.3
AD8IN
OSVDD
C3615
0.1u B
C3616
0.01u B
C3608
0.1u
C3614
0.01u B
ADAVDD
5
TAKO_C_OUT
C3603
0.01u
B
79
ADATOP
TS0
R1.1/P0
DYOUT0
R1.1/P0
DYOUT1
R1.1/P0
DYOUT2
R1.1/P0
DYOUT3
R1.6/P0
DYOUT4
R1.2/P0
DYOUT5
R1.0/P0
DYOUT6
R1.3/P0.1
DYOUT7
R3617
680
TO(7/18)
ADAIN
R3659
3900
C3612
1u
74
ADABOT
Q3602
UP04601008S0
BUFFER
TD_3-4
0
0.2
C3636
22p
CH
TMS
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
0.2
TAKO_Y_OUT
C3611
0.01u
B
0.7
0.7
DVSS4
2.8
0.1
Q3601
2SA1774HT2L
AMP
0
TO(7/18)
0.7
20 19 18 17 16 15 14 13 12 11 10
12
C3601
10u
4V
TCK
TD_2-3
R3658
1k
12
83
84
TO(10/18,11/18
13/18,17/18(CN1104))
TO(10/18)
63
TO(5/18,10/18,11/18
13/18,17/18(CN1117))
58
TO(5/18,10/18,11/18
13/18,17/18(CN1117))
42
TO(4/18,17/18(cn1104))
86
TO(17/18(CN1104))
43
TO(4/18)
20
TO(2/18,17/18(CN1104))
85
TO(17/18(CN1104))
C3631
0.1u
B
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
R3611
10k
R3608
XX
R3660
2200
R3607
10k
2.8
D_2.8V
PLLVSS
2.8
PLLVDD
2.8
A_4.75V
TDI
L3601
10uH
XHI_SCK
1.5
C3604
6.3V
10u
TDO
REG_GND
HI_SO
XSYS_RST
VCXOO
TO(18/18)
XCS_ALIGN
R3657
100k
R2.8/P2.6
C3610
10u
4V
C3633
10u
4V
C3622
0.01u
B
1608
R0.1/P0.3
FB3601
0uH
TCK
L3602
10uH
TMS
HI_SI
A_2.8V
82
11
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
VIDEO A/D CONV.
TCK
TMS
TD_2-3
TD_3-4
IFI_Y0
IFI_Y1
IFI_Y2
IFI_Y3
IFI_Y4
IFI_Y5
IFI_Y6
IFI_Y7
C3634
0.1u
B
IFI_C0
IFI_C1
IFI_C2
IFI_C3
IFI_C4
IFI_C5
IFI_C6
IFI_C7
IFI_VD
22
TO(2/18,13/18
17/18(CN1104))
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
TO(1/18,2/18
5/18,17/18
(CN1104))
IFI_HD
SPCK
SIGNAL PATH
CHROMA
AFCK
2.8
C3626
0.1u
B
VIDEO SIGNAL
Y
21
TO(2/18,17/18(CN1104))
33
TO(4/18,17/18(CN1104))
IFI_OE
R3656
0
C3629
0.1u
B
Y/CHROMA
REC
PB
16
4-29
4-30
VIDEO AD CONVERTER
VC-254 (8/18)

10
VC-254 BOARD(9/18)
HI8/STD8 PB RF AMP(RF(8)BLOCK)
REG_GND
RP_4.75V

NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
87 TO(18/18)
A_2.8V
DV_PB_RF
72 TO(6/18)
PB_RF
L3201
22uH
F0_ADJ_RF_IN
88 TO(17/18(CN1108))
RF_ENV
C3203
10u
6.3V
C3204
XX
PB_RF
XX
C3207
C3213
0.047u
B
RP_PB_MODE
2.8
0
0
AGC_SLOW
RP_PB
R3205
470k
DOC_DET
GND
IC3201
RF_ENV_DET
0.8
C3214
XX
REC_L_CONT
R3212
560k
2.8
IC3202
0.9
RF ENV DET
IC3202
TA75S393F-TE85R
MT_CONT
R1.4/P2.5
MT_F0
MT_CONT
MT_F0
R3214
220k
2.9
C3217
0.01u
B
MT_Q
MT_Q
C3216
0.1u
B
RP_IR
DOC_DET
RP_IR
DOC_DET
RF_ENV_LEVEL
VIDEO SIGNAL
C3218
XX
CHROMA
16
Y/CHROMA
AUDIO
SIGNAL
REC
PB
Hi8/STD8 PB RF AMP
VC-254 (9/18)
4-31
91 TO(11/18,13/18)
37 38 39 40 41 42 43 44 45 46 47 48
0
4.7
MT_CONT
4.7
1
VCC3
AFM IN
SWP
AFREC
PCM REC
RAMP
REC DUMP2
BOTH_REC/DV PBPS
GND
R3210
10k
R3213
470k
REC_Y/MT_CONT
REC2 OUT
RAMP CONT
8
6
5
Y MIX
R1.5/P2.6
YLPFOUT/CARDETOUT
PB2 IN
PCM IN
16 TO(2/18)
DOP
C3212
0.01u B
Y/C/ATF IN
BIASADJ
DOP
11 TO(1/18,2/18)
RF_AGC_OUT
RP_IR
PB DUMP2
GND
C3211
XX
C3210
4700p B
0
RP_IR
CXA3265R-T4
VSSW2 OUT
RF AGCOUT
IC3201
PB DUMP1
PB_C_RF
4.4
0
HI8/STD8 PB RF AMP
VCC AMP
DOC_DET
PB1 IN
AGC TC
2.4
90 TO(11/18)
RP_POWER_SAVE
C3215
0.01u B
R3206
470k
REC1 OUT
10 11 12
MT_F0
R0.1/P0
PBRFOUT
PCMOUT/MTSW
MT_Q
R0.9/P0.7
MTIN
R2.0/P2.7
CARDET
VCC
0
RAMP IR
REC1 IN
RAMP V1
Q3201
DTC144EHT2L
B
SWITCH
CLPFOUT
RAMP V2
REC DUMP1
REC2 IN
36 35 34 33 32 31 30 29 28 27 26 25
4.7
VPSW1 OUT
24 23 22 21 20 19 18 17 16 15 14 13
89 TO(15/18)
C3208
XX
2.1
4.7
0.5
4.7
R3215 150k
0.5%
C3205
0.01u B
C3206
0.01u B
C3202
0.01u
B
MT_F0
MT_Q
4-32
92 TO(12/18)

2
3
1
97 TO(10/18)
EXT_MIC_DET
66 TO(5/18)
58 TO(5/18,8/18,11/18,
13/18,17/18(CN1117))
0.1
MELODY
XCS_MECHA
XCS_OSD
XSYS_RST
XOSD_SCK
XCS_DS
LCD_LED_ON
SHOE_ON
XCS_MECHA
V_JACK_IN
EXT_MIC_DET
XS_JACK_IN
KEY_AD0
XIR_LED_ON
BATT_LI_3V
Q4813
UP04213008S0
R4896
XX
XLANC_PWR_ON
XSYS_RST
R4817
8.3
KEY_AD2
106 TO(17/18(CN1117))
R4867
470k
R4868
470k
KEY_AD3
KEY_AD4
KEY_AD0
KEY_AD1
KEY_AD2
KEY_AD3
KEY_AD4
R4869 470k
1k
RB4817
10k
61 TO(5/18)
XVTR_MODE_SW
XCAM_MODE_SW
R4816
1k
B
B
0.01u
R4813
0.01u
0.01u
C4808
XIR_LED_ON
BATT_LI_3V
EVF_DD_ON
KEY_AD5
1k
TL1596CPWR
UNREG
LANC_DC
NC
R4818
3.0
C
DATA
LANC_SIG
C4810
C4811
DIAL_B
R4862
1k
R4861
1k
XPHOTO_STBY_SW
XS/S_SW
C4812
0.01u
XPHOTO_FREEZE
C4813
0.01u
XEJECT_SW
C4814
0.01u
XVTR_MODE_SW
XCAM_MODE_SW
XPHOTO_STBY_SW
D4804
MA111-(K8).S0
XPHOTO_FREEZE
XEJECT_SW
C4817
0.1u
R4833
470k
0.5%
C4816
0.1u
B
108 TO(17/18(Q1104))
TALLY_LED
B
XCS_LCD_DRIVER
LCD_LED_ON
LCD_COM/XDATA
XCS_LCD_DRIVER
109 TO(17/18(CN1117))
LCD_LED_ON
LCD_COM/XDATA
R4834
LANC_DC
XCS_DS
C4805
10u
10V
470k
0.5%
OSD_SO
R4835 1M
XOSD_SCK
R4836 1M
XCS_DS
110 TO(17/18(CN1104))
BEEP
111 TO(15/18)
BEEP
0.5%
0.5%
DS_RESETM
DS_RESETM
MS_IN
112 TO(17/18(CN1104))
MS_IN
INIT_CHARGE_ON
XCS_EVF
BATT/XEXT_SW
BATT_SIG
BATT_SIG
VDD
100k
100k
10k
R4885
1k
R4888
R4887
R4898 1M
XCS_ALIGN
XCS_ALIGN
84 TO(8/18)
HOTSHOE_ID2
HOTSHOE_ID1
B
R4886
2.8
1k
USB_DET
SHOE_CONT_AD
RB4812
1k
R4897
1k
MS_IN
DIAL_B
2.7
DIAL_A
2.7
BATT/XEXT_SW
0
0
2.4
C4820
6800p
B
2.9
SYS_V
R4882
470
3.0
XCS_LCD_DRIVER
2.9
C4823
0.1u B
SIRCS_ENV
XCS_ALIGN
2.9
DS_RESETM
2.9
0
R4884
MELODY_ENV
TALLY_LED
1.5
1.1
2.9
C4821
22p
CH
X4802
32.768kHz
100k
R4873
100k
XOSD_SCK
OSD_SO
IR_ON
FAST_CHARGE
20MHz
X4801
0.022u
0.1u
2.8
54 TO(5/18)
R4864
560k
C4819
HI_TEST_A
MELODY
XHI_SCK
HI_SO
0.1u
LANC_DC
XLANC_JACK_IN
LANC_SIG
C4825
2.8
LANC_SIG
0.3
0.3
2.8
2.8
2.7
R4863 47k
2.9
1.4
1.4
2.9
0.1
2.5
2.1
2.4
HI_SI
DS_MAD
XLANC_JACK_IN
VTR_DD_ON
CAM_DD_ON
1k
R4855
100k
XCS_LCD
R4840
XCS_EVF
R4872
XCS_OSD
RB4814
100kx4
1M
2.9
2.9
2.9
2.9
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
R4832
C4824
XLANC_JACK_IN
C4822
15p
CH
SHOE_ON
SHOE_ON
LANC_DC
R4899
100k
32KHZ_IN
R4878
EXT_MIC_DET
2.7
SHOE_ON
R0/P2.7
XCS_MECHA
2.7
XCS_DS
2.9
LCD_LED_ON
2.9
AVDD
2.9
AVREF_1
2.9
33
GND
32KHZ_OUT
C4827
0.01u
B
R4883
470k
2.8
1608
GND
VDD
2.9
VDD(PWE)
2.9
XS_JACK_IN
2.7
V_JACK_IN
2.7
RCH_DET
N.C
2.8
KEY_AD0
KEY_AD1
2.8
2.8
KEY_AD2
ACV_SENSE
2.5
BATT_SENSE
2.5
N.C
34
2.9
R4876 10M
LCD_COM/XDATA
FAST_CHARGE
BATT/XEXT_SW
KEY_AD3
TXD
R0.1/P0.4
RXD
FAST_CHARGE
105 TO(17/18(CN1113))
2.8
TALLY_LED
XLANC_POWER_ON
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
0
2.9
MELODY_ENV
XPHOTO_STBY_SW
FAST_CHARGE
INIT_CHARGE_ON
DS_RESETM
XPHOTO_FREEZE
IB_SI
LCD_COM/XDATA
R4811
100k
XCC_DOWN
IB_SO
XCS_ALIGN
CHARGE_INH
2.8
HI_RXD
LANC_SIG
INIT_CHARGE_ON
R4830 1k
SIRCS_ENV
XEJECT_SW
XOSD_SCK
HI_TXD
XS/S_SW
XCS_OSD
XLANC_PWR_ON
2.9
BATT_IN
OSD_SO
6
2.6
2.9
TEST_PORT
XCS_LCD_DRIVER
IR_ON
XPHOTO_STBY_SW
LCH_DET
GND
R2.9/P0
XVTR_MODE_SW
R0/P2.9
XCAM_MODE_SW
20MHZ_IN
INIT_CHARGE_ON
XPHOTO_FREEZE
R4829 1k
SYS_V
CXP921064A-032R-T6
XLANC_ON
VDD
LANC_SIG
0.3
IC4803
XDS_FLASH_RST
XRESET
SHOE_CONT_AD
SHOE_CONT_AD
DS_BUSY
20MHZ_OUT
DIAL A
BATT/XEXT
EVF_DD_ON
GND
2.9
XCC_DOWN
DIAL B
XSYS_RST
MELODY/SIRCS_CARRIER
XEJECT_SW
HI CONTROL
TEST_PORT
2.9
MS_IN
XDS_WAKE_UP
xHI_SCK
XS/S_SW
XIR_LED_ON
HI_SO
104 TO(17/18(CN1101))
KEY_AD4
2.8
XCAM_MODE_SW
SHOE_CONT_AD
IC4803
XF_TALLY_LED
HI_SI
HOTSHOE_ID2
HOTSHOE_ID2
Q4804
HOTSHOE_ID1
HOTSHOE_ID1
3.0
4
BATT SIGNAL
I/O
0.3
D4803
MA111-(K8).S0
XF_TALY_LED
XF_TALY_LED
BATT_SIG
103 TO(17/18(CN1116))
SIRCS_SIG
R4803
100k
2.8 5
2.8
N.C
0
RB4801
1kX4
SIRCS_PWM
SIRCS_SIG
KEY_AD5
1
2
3
4
0
2.8
USB_DET
XCHARGE_LED
XLI_PRE_END
SIRCS_PWM
2.8
EVF_DD_ON
XLANC_ON
Q4804
HN1L02FU(TE85R)
IR_ON
XSYS_RST
XDS_FLASH_RST
IC4801
S-84239FS-T2
IR_ON
102 TO(12/18)
R4821
2.9
HOTSHOE_ID1
XSIRCS_IN
DS_MAD
RESET
CS
XVTR_MODE_SW
XDS_WAKE_UP
HOTSHOE_ID2
XCS_VC
XLANC_JACK_IN
D4806
MA132WK-(K8).SO
XCC_DOWN
XCC_DOWN
3.0
1.6
BATT_UNREG
101 TO(14/18)
VBAT
3.0
4
C4802
0.1u
B
VTR_UNREG
BATT_LI_3V
100 TO(17/18(CN1113))
VOUT
XIR_LED_ON
AVREF_0
LANC_OUT
VTR_DD_ON
PREEND
3.1
7.6
RB4818
100k
GND
XCS_LCD
R2.9/P0
CAM_DD_ON
VIN
R0/
P0.5
0.1
SYS_V
2.8
SIRCS_SIG
3.0
XF_TALLY_LED
2.9
VRO
VSS
LANC_IN
0.3
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
XX
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
0.3
XCS_VC
RESET
1k
SYS_V
R4808
0
R4804
C4815
0.1u
B
R4805
99 TO(11/18)
HI_SI
HI_SI
IC4801
D4802
MA728-(K8).S0
HI_SO
3.3
17/18(CN1104))
VOUT
VIN
13/18,17/18(CN1117))
83 TO(8/18,11/18,13/18,
HI_SO
NC
GND
63 TO(5/18,8/18,11/18,
7.6
XHI_SCK
XHI_SCK
XDS_WAKE_UP
XDS_WAKE_UP
XDS_FLASH_RST
98 TO(17/18(CN1104))
XDS_FLASH_RST
1
470k
IC4804
S-817A33ANB-CUW-T2
47k
RB4803 RB4804
470kX4 470kX4
VOLTAGE DETECT
DS_MAD
DS_MAD
R4822
V_JACK_IN
USB_DET
KEY_AD6
IC4804
V_JACK_IN
C4806
33u 4V
C4807
0.1u B
XS_JACK_IN
FB4801
0uH
USB_DET
XS_JACK_IN
107 TO(17/18(CN1113))
XS/S_SW
TALLY_LED
R4823
10k
B
SIRCS I/F
R4814
10k
EVER_3.0V
75 TO(7/15)
20
DIAL_A
KEY_AD5
LANC I/O
10 11 12 13 14
LANC_SIG
XCS_OSD
DIAL_B
1200
1200
DATA
WAKE
VCC
EXT_MIC_DET
OSD_SO
59 TO(5/18,17/18(CN1117))
19
DIAL_A
IC4802
R4820 100k
18
KEY_AD1
5.6
17
KEY_AD0
R4815
10k
SIRCS_PWM
XCS_EVF
XCS_LCD
R4819
1200
IC4802
R4810
1k
0.3
XCS_MECHA
NC
GND
NC
3.0
96 TO(13/18)
2.5
XCS_VC
R4807
2200
XCS_LCD
POWER
2.8
0.3
XCS_EVF
C4804
0.1u B
R4802
4700
62 TO(5/18)
XCS_VC
BUFFER
0
SIRCS_ENV
0.1
95 TO(17/18(CN1117))
CAM_DD_ON
R4824
2700
C4803
0.1u
B
VTR_DD_ON
CAM_DD_ON
NC
D_2.8V
VTR_DD_ON
94 TO(11/18)
16
15
EVF_DD_ON
HI_RXD
Q4802
2SC4738F-Y/GR(TPL3)
KEY_AD1
HI_TXD
REG_GND
CAM_DD_ON
KEY_AD2
3.0
HI_TEST_A
KEY_AD3
BEEP
R4806
1k
14
HI_XRESET
R4812
C4801
1u
Q4806
RN2102F(TPL3)
LANC SW
KEY_AD4
XLANC_ON
R4809
1k
KEY_AD5
3.0
R4801
47k
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
5 TO(1/18)
13
HI_RXD
2.8
BUFFER
MELODY_ENV
HI_TXD
Q4801
2SC4738F-Y/GR(TPL3)
HI_TEST_A
MODE CONTROL (HI BLOCK)
93 TO(18/18)
12
11
NOT
USE
VC-254 BOARD(10/18)
A
10
16
4-33
4-34
MODE CONTROL
VC-254 (10/18)
99 TO(10/18)
17
18
19
121 TO(17/18
MF_LED
MF_A
LD,KINUTA
(CN1116))
MF_B
ZM_RST_LED
(CN1113))
LENS_FILTER_ON_SW
FC_RST
HALL_AD
IRIS_PWM
ZM_RST
FC_RST_LED
16
15
120 TO(17/18
26 TO(3/18)
XCS_CH
CH_SO
XCH_SCK
XRST_KINUTA
XVC_SCK
VC_SO
XCS_KINUTA
AFC_F0
TBC_VD
XTBC_V_RST
MECHA_HD
MECHA_FLD
MECHA_VD
X1/2_SWP
ATF_SAMPLE
SWP_DIR
14
9 TO(1/18)
2/18)
ZOOM_VR_AD
13
8 TO(1/18,
18 TO(2/18)
LENS_TEMP_AD
12
11
LINE_OUT_V
AGC_SLOW
RP_PB_MODE
RP_POWER_SAVE
SIGNAL PATH
ZOOM_VR_AD
Drum phase servo
MF_B
MF_LED
Drum servo (speed and phase)

MF_A
ZM_RST_LED
LENS_FILTER_ON_SW
LENS_TEMP_AD
FC_RST
HALL_AD
IRIS_PWM
ZM_RST
FC_RST_LED
XCS_CH
CH_SO
XCH_SCK
XRST_KINUTA
XVC_SCK
VC_SO
VC_SI
XCS_KINUTA
TBC_VD
XTBC_V_RST
MECHA_HD
MECHA_FLD
MECHA_VD
JOG_VD
ATF_SAMPLE
REC/PB
Drum speed servo
X1/2_SWP
LINE_OUT_V
XME/MP
10
REC
RP_POWER_SAVE
XME/MP
VC_RF_SWP
VC_RF_SWP
DA_STB
VC_RF_SWP
VC_SO
DA_STB
VC_RF_SWP
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
VC_SO
XVC_SCK
CAMERA CONTROL,HI8/STD8
MECHA CONTROL,
STEADY SHOT(VC,SE BLOCK)
XVC_SCK
VC-254 BOARD(11/18)
A
57 TO(5/18)
VC_SI
8
90 TO(9/18)
JOG_VD
69 TO(6/18)
17/18(CN1108))
SWP_DIR
5
71 TO(6/18,15/18,
RP_PB_MODE
4
119 TO(12/18)
AGC_SLOW

Refer to page 4-104 for waveform.
2
3
1
Capstan speed servo

Capstan servo (speed and phase)
SYS_V
SYS_V
SYS_V
7 TO(1/18,2/18)
CK_CONT1
CK_CONT1
CK_CONT2
58 TO(5/18,8/18,10/18,
XSYS_RST
13/18,17/18(CN1117))
X0
113 TO(13/18)
XTAL20M
GENERAL_AD
SYSTEM_AD
1.2
VC_SO
17/18(CN1104))
NOT USE
MF_B
R4924
47k
R4925
470k
R4926
470k
ZOOM_VR_AD
LENS_TEMP_AD
R4918
2200
HALL_AD
XCS_CH
C4910
0.1u
B
CH_SO
XCH_SCK
R4927 47k
VC_SI
R2004
22k
XCS_VC
HI_SI
XHI_SCK
R2010
15k
C2010
22u
6.3V
R2008
1M
1.5
YAW_AD
C2006
0.056u
B
R2003
22k
2.8
1.3
IC2001
UPC6756GR-8JG-E2
IC2001
VCC
PASS
1.3
OUT1
1.3
AM2
CRST
OUT2
1.3
HO1
Vref2
Vref1
HI1
11 12 13 14 15 16 17 18 19 20
VST_C_RESET
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1.3
100k
1.3
R4929
1.3
100k
1.3
R4928
1.3
1.3
C2005
0.056u
B
CAP_ON
VC_F_BUSY
1.3
HO2
7
LO1
0.8
8
LIA1
GND
0.1u B
HI2
10
CAP_PWM
R4921
10k
0.8
DRUM_PWM
LO2
IRIS_PWM
R4920
10k
C4911
C2012
0.33u
B
R2007
10k
PITCH_AD
0.6
CL4901
R4922
47k
C2009
0.056u
B
C2016
XX
C2003
0.1u
B
R4930
100k
XCS_VC_STAR
CL4903
R4932
47k
R4931
47k
C2007
0.056u
B
HI_SO
0.6
LIB2
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
94 TO(10/18)
VC_F_BUSY
YAW/PITCH
SENSOR AMP
R2005
1M
C2008
22u
6.3V
C2017
XX
R2006
10k
REG_GND
1k
XCS_VC
XCS_VC_STAR
VC_F_BUSY
LCD_HOLD
EEPROM
R4944
83 TO(8/18,10/18,13/18,
MF_A
CAP_FWD
JOG_VD
Not Used/XLM_LIM_ON
IC4901
SSS/Not Used
Not Used/LM_LIM_CONT
XVC_SCK
SYSTEM_AD
LENS_DETE
2.8
DRUM_BRAKE
0
Not Used/DRUM_TEMP_AD
YAW_AD
PITCH_AD
R0.9~1.5
T_REEL_FG_AD
R0.9~1.5
S_REEL_FG_AD
XFF_REW_UP
AVDD
AVRH
AVSS
VSS
STB_ON
INT_VD
CK_CONT1
TBC_V_RST
SYS_V
CFG_HMS
CK_CONT2
TBC_VD
MECHA_HD
MECHA_FLD
Not Used/XREEL_HALL_ON
1k
13/18,17/18(CN1117))
HI_SI
XCS_VC_STAR
R4923
47k
R4943
LIB1
CL4904
XDRUM_BRAKE
C4909
0.01u B
1.3
1.3
C4908
0.01u
B
2.8
STB_ON
R4935
100k
R2.8/
P0
2.4
1.4
R0/P0
R1.4/P0
R2.8/P0
2.8
2.8
R1.1/P1.4
CAP_FG
DRUM_FG
LINE_OUT_V
DRUM_PG
MECHA_VD
RESERVED
VDD
1
2
3
4
XCS_EEPROM
TAPE_LED_ON
(OSCO) NC
2.8
VDD
0
VC_F_BUSY
2.8
CAP_ON
2.8
CAP_FWD
XWEN/Not Used
C4906
0.1u
B
2.8
XDRUM_BRAKE
(OSCI) GND
XWE_EEPROM
RP_PS
2.8
CSE2P
HI8_MP_SW
HI8_MP_SW
XDRUM_BRAKE
VDD
FC_RST_LED
117 TO(14/18)
RB4903
100k
VSS
AGC_SLOW
2.8
ME_SW
ME_SW
FC_RST_SENS
Not Used/XFE_ON
WEE2P
TREEL_AFG
ZM_RST_SENS
AUDIO_OUT
R2.8/P0
MF_LED
2.8
D_START
FC_RST
TREEL_AFG
ZM_RST_LED
X1/2_SWP(HSWP)
2.8
SREEL_AFG
DA_STRB
Not Used/XSG_V_RST
ZM_RST
SREEL_AFG
Not Used/XCS_AU
RP_PB_MODE
2.8
SWP
MODE_SW_C
ZM_RST_LED
ATF_SAMPLE
DA_STB
MODE_SW_C
XCS_KINUTA
TAPE_TOP
MODE_SW_B
MODE_SW_B
XRST_KINUTA
TAPE_END
MODE_SW_A
MODE_SW_A
Not Used/XCS_IO
XNS_ON_SW
2.1
IC4902
MB91192PFF-G-134-BND-ER
Not Used/DOP
R2.7/P0
RF_ENV_DET
XCS_KINUTA
XME/MP
HI8_MP_SW
XRST_KINUTA
2.8
CAMERA CONTROL,
HI8/STD8 MECHA CONTROL
DRUM_ON
ME_SW
DRUM_PWM
IC4902
Not Used
MSW_B
2.8
Not Used
MSW_C
XME/MP
Not Used
VSS
2.8
Not Used
UNLOAD
DRUM_ON
CAP_PWM
CAP_PWM
XRST_VC
MSW_A
R2.8/P0
TAPE_TOP
DRUM_PWM
MD0
TAPE_END
TAPE_TOP
MD1
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
LED
DRIVE
Q4901
RN1102F(TPL3)
UNLOAD
TAPE_END
MD2
R0.1/P3.7
LOAD
LOAD
UNLOAD
VSS
R4901
1k
MF_LED
TAPE_LED_ON
TAPE_LED_ON
X1
2.8
DRUM_PG
XCS_VC
1.2
GENERAL_AD
2.8
MF_A
R0.1/P2.8
MF_B
1.4
ZOOM_SW_AD
1.6
LENS_TEMP_AD
3.0
AFC_F0_IN
R1.4/P0.2
HALL_AD
2.8
CS_CH/GCAM_PB
0
CH_SI/CAM/XLINE
2.8
SCK_CH/AGC_DIRECT
2.5
(TANUKIVC) VC_SI
R0.2/P0.7
(VCTANUKI) VC_SO
2.5
SCK_VC
2.9
XCS_VC
2.1
(HIVC) HI_SO
2.4
(VCHI) HI_SI
2.5
HI_SCK
2.8
XCS_VC_STAR
0
PITCH_PWM
0
(V_LIGHT_PWM)YAW_PWM
R1.4/P0
IRIS_PWM
1.2
DRUM_PWM
0.5
CAP_PWM
VST_C_CHARGE
C4905
0.01u B
DRUM_FG
DRUM_FG
DRUM_PG
35
X0
DRUM_ON
DRUM_ON
14/18)
CH
CAP_FWD
CAP_FWD
116 TO(13/18,
10p
C4904
CAP_ON
CAP_ON
1.1
R4906
0
1.0
X4901
20MHz
CAP_FG
CAP_FG
R4902
560k
DRUM_START
DRUM_START
63 TO(5/18,8/18,10/18,
HI_SO
HI_SI
120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91
R4903
0
HI_SO
LIA2
R4905
XX
C4912
0.01u
B
C4903
10p
CH
1.4
RF_ENV_DET
RF_ENV_DET
0.1
R0/P2.8
2.8
C4907
0.1u
B
91 TO(9/18)
XHI_SCK
STB_ON
STB_ON
(CN1101))
AM1
SREEL_AFG
YAW_AD
R4915
4700
PITCH_AD
R4916
4700 TREEL_AFG
CK_CONT1
SYS_V
CAP_FG
XTBC_V_RST
MECHA_HD
MECHA_FLD
CAP_FG
TBC_VD
LINE_OUT_V
R4936
100k
XHI_SCK
115 TO(17/18
LOAD
SSS_FROM_VC
SSS_FROM_VC
DRUM_FG
(CN1104))
DRUM_PG
XWEN_FROM_VC
XWEN_FROM_VC
114 TO(17/18
MECHA_VD
R2009
XX
C2011
XX
VREF1
SE_2.8V
4700
2.8
2.8
2.8
2200
R4917
1k
R4913
R4912
R4911
R4910
2.8
2.7
0.1
100k
2.8
100k
R4908
LIA2
C2002
0.1u
B
JOG_VD
XWEN_FROM_VC
SSS_FROM_VC
RP_POWER_SAVE
AGC_SLOW
DRUM_START
X1/2_SWP
VC_RF_SWP
RP_PB_MODE
ATF_SAMPLE
TAPE_END
LENS_FILTER_ON_SW
TAPE_TOP
HI8_MP_SW
RF_ENV_DET
16
VC-254 (11/18)
R2001
22k
L2001
10uH
CAMERA CONTROL, Hi8/STD8 MECHA CONTROL, STEADY SHOT
LIA1
R2002
22k
FC_RST_LED
WEE2P
ME_SW
56k
RST
GND
MODE_SW_C
100k
2.8
OI
OO
2.5
MODE_SW_B
68k
XSCK xBUSY
MODE_SW_A
47k
VC_SI
R0.2/
P0.7
UNLOAD
R1132
56k
VC_SO
R1132
*
LOAD
R1131
68k
R1128
*
2.8
VST_C_RESET
R4904
100k
TAPE_LED_ON
R1128
68k
Vcc
SWP_DIR
56k
XCS
SYSTEM_AD
R1127
2.8
2.5
XVC_SCK
CSE2P
GENERAL_AD
R1131
*
TRV530
R1127
*
TRV330
*MARKED:MOUNT TABLE
TRV230
IC4901
AK6480AM-E2
A_2.8V
REF.NO.
100k
D_2.8V
C4902
1u
B
1608
FB4901
0uH
118 TO(18/18)
VREF2
4-36
C2014
10u
4V
C2015
0.01u
B
122 TO(17/18(CN1116))
PB

10
12
11
13
14
VC-254 BOARD(12/18)
A
EVR, LASER LINK(ER,IR BLOCK)
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
NO MARK:IR ON/IR OFF MODE

( ):IR ON MODE
[ ]:IR OFF MODE
AU_2.8V
R3940 0
L2291
10uH
C3914
10u
6.3V
1.2
HALL_GAIN
0.8
HALL_OFFSET
2.8
0
HALL_OFFSET
24
HALL_OFFSET
HALL_REF
TO(3/18)
HALL_REF
VC_RF_SWP
C3905
0.3
0.47u
B
(2.3)/[3.6]
IR_L
DA_STB
128
(0.9)/[0]
TO(15/18)
IR_R
ZOOM_MIC_CONT
1.5M_DEV
FRQ_TUNE
ZOOM_MIC_CONT
125
TO(1/18)
C3906
0.47u
B
TO(16/18)
1.5M_DEV
1.7M_DEV
126
1.7M_DEV
AU_BPF
TO(15/18)
AU_BPF
IR_CARR
IR_V_DEV
AFC_F0_ADJ
15
AFC_F0_ADJ
TO(2/18)
C3934
1u
B
4.7
470
IR DRIVE
39
IC3901
LA9511WL-TBM
NC
(1.3)/[0]
MIX IN
NC
(2.3)/[3.6]
REF
NC
(2.3)/[2.7]
VRF OUT
(2.3)/[2.6]
ARF OUT
(3.0)/[0]
STBY
(2.9)/[0]
CHUP C
A DEV ADJ
Lch IN
37
ALC C
(2.3)/[3.6]
Rch IN
9
3.3
R3911
22k
0.5%
C3915
0.01u
B
32
TO(4/18)
IR_FSC
IR_ON
TO(10/18)
R3921
470
R3919
560
(1.3)/
[0]
C3936
0.01u
B
3.4
C3919 C3916 C3920

0.47u
0.47u
1u
B
B
B
145
IR_DRV_EM
TO(17/18(CN1116))
R3939
0
Q3902
2SA1226-T1E4
BUFFER
R3924
470
C3926
0.01u
B
R3920
6800
SIGNAL PATH
C3927
0.01u
B
VIDEO SIGNAL
CHROMA
R3922
39k
Y/CHROMA
AUDIO
SIGNAL
REC
10 11 12
R3909
1M
102
R3923
470
R3948
XX
(0.6)/
[0]
NC
V IN
(1.3)/[0]
REG
NC
(0.6)/[0]
DRV EM OUT
(2.0)/[0.5]
DRV SW
(1.3)/[0]
MIX OUT
IC3901
V DEV ADJ
(3.9)/[4.7]
R3916
V GND
HPF OUT
(2.3)/[3.3]
V REF
(2.3)/[3.3]
VRF IN
(2.3)/[3.3]
V GND
NC
NC
IR_A_DEV
C3903
10u
6.3V
VCC
PRE EM OUT
(2.1)/[2.2]
VCC
CAR ADJ
PRE EM IN
CLAMP C2
(2.2)/[0.1]
C3908
1u B
DRV CL OUT
(3.9)/
[4.7]
C3935
0.01u B
C3902
10u
4V
HALL_GAIN
0.8
(2.4)/
[0.2]
XX
R3943 12k
(2.3)/
[3.3]
IR_VIDEO
TO(7/18)
FRQ_TUNE
C3901
XX
VC_RF_SWP
HALL_GAIN
1.0
4.7
Q3903
2SA1774HT2L
SWITCH
(4.6)/[0]
38
13 14 15 16 17 18 19 20 21 22 23 24
STB(LD)
HALL_REF
IR_A_DEV
R3936
1500
OSC VCC
SWP(SEL)
MT_Q
0.9
77
TO(11/18)
CLAMP C1
LPF R
GND
0.5
DA_STB
VC_RF_SWP
R3905
33k
LPF L
D_3.2V(VDD1)
HALL_GAIN
HALL_OFFSET
IR_V_DEV
DA_STB
119
L3903
33uH
C3917
0.1u
B
R3917 150k
2.8
A_FADE
FRQ_TUNE
1.0
XVC_SCK
A GND
C2291
1u
B
1.7M_DEV
MT_Q
HALL_REF
1.6
R3904
4700
A GND
2.8
AGC_CONT2
RP_IR
AFC_F0_ADJ
IR_V_DEV
Xtal IN
ZOOM_MIC_CONT
FRQ_TUNE
2.0
TO(14/18)
VC_SO
XVC_SCK
0
124
CFG_DUTY
VC_SO
[OSC OUT]
1.6
AU_BPF
AFC_F0_ADJ
CFG_DUTY
4.7
1.7M_DEV
1.5M_DEV
RP_IR
VC_SO
[ALC OUT Rch]
1.9
RF_AGC_CONT
DOC_DET
Xtal SEL
1.8
AU_BPF
CFG_DUTY
DOC_DET
0.9
RF_ENV_LEVEL
R3913
1k
REG_GND
C3923
39p
CH
36 35 34 33 32 31 30 29 28 27 26 25
MT_Q
RF_ENV_LEVEL
C3921
33p
CH
TO(18/18)
L3904
33uH
[ALC OUT Lch]
ACC/RF_CONT
1.5M_DEV
FB2291 0uH
6
1.6
MT_F0
0.9
REC_L_CONT
REC_BIAS
IR_A_DEV
CFG_DUTY
REC_Y/MT_CONT
XVC_SCK
R3912
330
(1.3)/[0]
2.9
DI
2.5
R0.3
P0.7
TO(9/18)
48 47 46 45 44 43 42 41 40 39 38 37
4
2.1
IR_CARR
MT_F0
CLK
92
DOC_DET
MT_Q
15 16 17 18 19 20 21 22 23 24 25 26 27 28
2.9
1
RF_ENV_LEVEL
A_4.9V(VDD2)
0.8
14 13 12 11 10
MT_CONT
A_4.9V(VCC)
MT_F0
DOC_DET
EVR
BH2222FV-E2
IC2291
4.7
MT_CONT
MT_F0
R3942
IC2291
C3910
4.7u
6.3V
RP_IR
MT_CONT
C3909
0.01u
B
(2.1)/[2.3]
R3903
33k
RP_IR
XX
IR_CARR
C3918
4p
CH
L3902
5.6uH
144
A_2.8V
R3941
XX
C3913
510p
CH
C3911
0.01u
B
R3908
12k
A_4.75V
L3901
10uH
C3912
0.01u
B
R3949
C3904
0.01u
B
C2293
22u
6.3V
REF R
C2292
0.01u
B
BAND SEL
PB
4.7
R3918
150k
C3922
1u
B
C3924
1u
B
C3925
0.1u
B
C3928
22u
4V
SIRCS_PWM
16
4-37
4-38
EVR, LASER LINK

VC-254 (12/18)

2
1
VC-254 BOARD(13/18)
10
11
12
13
14
15
16
REG_GND
DIGITAL8 MECHA CONTROL(MC BLOCK)
DRP_SO
DRUM_8PB
XCS_TRF
91
TO(9/18)
132
TO(17/18
(CN1108))
RF_ENV_DET
SDC_IN
VFI_OE
XRST_VSP
MCCE
SWP_75Hz
/REEL_ON
DRP
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
TAPE_END
0.1
TAPE_LED_ON /ME_F_BUSY
2.8
REC_CRRT0 /DEBUG_OUT1
2.8
REC_CRRT1 /DEBUG_OUT2
0
SCOD_WINDOW
R1.2/P2.8
XFE_ON/REEL_FWD
1.4
SWP
TAPE_TOP
LM_LIM_DET /CM_LIM_DET
LM_LIM_ON /CM_LIM_ON
LM-
LM+
RSAT
RST
DO
GND
XFE_ON
DV_RF_SWP
XDRP_SCK
VC-254 (13/18)
8
7
R4527
100k
2.8
2.8
0
DEM1
2.8
DEM0
2.7
R4520
1k
0
R4511 1k
116
TO(11/18,14/18)
134
TO(14/18)
DRUM_PWM
DRUM_FG
DRUM_PG
LOAD
UNLOAD
UNLOAD
TAPE_LED_ON
TAPE_LED_ON
TAPE_TOP
TAPE_TOP
TAPE_END
TAPE_END
R4523
470k
HP_JACK_IN
2.8
LIP_SLEEP
2.1
HI_SO
SREEL_FG
2.4
HI_SI
TREEL_FG
2.5
XHI_SCK
2.8
DEW_AD
R4524
100k
DRP_SI
CL4503
2.8
CL4504
DRP_SO
RB4502
100k
VSP_SI
0.3
CL4505
2.7
CL4506 XVSP_SCK
XREEL_HALL_ON
REC_PROOF_SW
REC_PROOF_SW
RSAT
LM_LIM_ON
LM_LIM_DET
LM_LIM_DET
DRUM_8PB
VSP_SO
XCS_MC_FLASH
0
2.7
XCS_MECHA
R0/P2.8
XCS_HONEY
R4521
TREEL_FG
LM_LIM_ON
LPS
2.5
SREEL_FG
RSAT
XDRP_SCK
DEW_AD
XREEL_HALL_ON
R4526
470k
XHI_SCK
63
TO(5/18,8/18,10/18,11/18,17/18(CN1117))
HI_SI
83
TO(8/18,10/18,11/18,17/18(CN1104))
XCS_MECHA
96
TO(10/18)
XSYS_RST
58
TO(5/18,8/18,10/18,11/18,17/18(CN1117))
HI_SO
10k
CAP_PWM
DRUM_PWM
R4522
2.8
0
10k
C4510
0.01u
DRUM_START
1.4
DV_RF_SWP
1.4
DRP
SIGNAL PATH
REC
Drum speed servo
Drum phase servo
Capstan speed servo
DRP_SO
DRUM_8PB
XCS_TRF
RF_ENV_DET
DV_RF_SWP
4-39
DRUM_START
DRUM_PWM
DRUM_PG
2.8
MC_F_BUSY
SWP
REC_CRRT1
2.8
ATF_ERR
REC_CRRT0
R4508
470k
DRUM_ON
DRUM_START
DRUM_FG
16
DIGITAL8 MECHA CONTROL
C4507
0.01u
B
2.8
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
SCOD_WINDOW
CAP_PWM
CAP_FG
DRUM_ON
2.8
1
2
1.4
OOE
XRST_VTR
XCASETTE_IN
SDC_IN /ATF_DEBUG_IN
DEW_DET
ATF_ERR
PLUG_DC_LEVEL /L_CASETTE
/S_ELTN_ERR
NC
RF_ENV_DET /T_ENLTN_ERR
VSS
AVSS
2.8
AVRH
2.8
AVDD
/CM+
BBI_LINE_X8
FRRV
TRRT
TRRV
CFG_COUNT
CFG_COUNT
XREEL_HALL_ON /CM-
DRUM_ON
MCHA1
DI
CAP_FWD
CAP_FG
2.8
0
R4502
2.8
1.4
0.1
0.6
AUDIO_MUTE
ATF_ERR
R4512 4700
CL4502
CL4501
1.4
1.4
1.4
1.4
DEW_AD
RF_ENV_DET
FRRV
XREEL_HALL_ON
TRRT
TRRV
VREF
DRUM_8PB
SREEL_FG
TREEL_FG
CAP_FG
1.4
0.1
1.4
CAP_FG
0~2.8
TREEL_FG
0~2.8
SREEL_FG
VREF /FP
DRUM_8PB/PLUG_DC_SW /FP_SEL
3
R4507
1k
MCHA0
XFE_ON
XDRP_SCK
MCDA7
SCOD_WINDOW
TO(6/18)
MCDA6
REC_CRRT1
68
MCDA4
REC_CRRT0
XFE_ON
DV_RF_SWP
MCDA5
VDD
DRUM_START
/DRUM_MASTER_CLOCK
TAPE_END
REC_CRRT1
MCDA3
TAPE_LED_ON
MCDA2
MCDA4
TAPE_TOP
ATF_ERR
REC_CRRT0
MCDA1
MCDA3
VSS
N.C.(XTAL)
LM_LIM_DET
TO(4/18)
MCDA2
XCS_HONEY /ATF_DEBUG
REEL_PWM
0.6
CAP_PWM
1.1
DRUM_PWM
GND(EXTAL)
VDD
R2.4/P1.6
MCDA0
R2.2/P1.6
MCDA1
R1.4/P1.0
MCDA2
R1.4/P0.8
MCDA3
R1.4/P1.5
MCDA4
LM_LIM_ON
38
MCDA0
31
XCS_XYZ2
UNLOAD
SCOD_WINDOW
MCDA1
XCS_TRF
MCCE
MCDA0
C4509
0.01u
XFF_REW_UP
2.8
MCHA1
XCS_VFD
XCS_XYZ1
LOAD
MCHA0
2.8
32
2.8
MCDA7
XCS_TRF
OFR
XRST_VSP
AUDIO_IN
RSAT
MCDA6
2.8
XCS_MC_FLASH /CAP_HICUE
XHI_CS_MC
XCS_DAC
DRUM_ON
XCS_AU
XCS_TAKO
CAP_FWD
MCDA5
LPS
XVSP_SCK
2.8
MCDA4
LIP_SLEEP
XCS_VFD
CAP_FWD
MCDA3
XRST_PHY
VSP_SO
RDX
CAP_ON
MCDA2
XCS_TAKO
2.6
LPS
WR01
2.8
MCDA0
MCDA1
2.8
DRP_SI
VSP_SI
CAP_ON
XCS_VFD
2.8
XCS_VFD
XHI_SCK
IC4501
XRST_VSP
XRST_LINK
RDX
XCS_EEP
DEM1 /XCS_DSP
DEM0
XDRP_SCK
ALE
R0/P2.8
XDVCN
REC_PROOF_SW
OFR
ALE
XDVCN
EEP_RST
DRP_SO
XVIDEO_IN
LPS
2.8
WRX
EEP_RDY/BSY
ANALOG_MUTE /PLUG_CONT/DEBUG_OUT0
LIP_SLEEP
DRP
CAP_ON
CAP_PWM
LOAD
MECHANISM CONTROL
REC_PROOF
ALE
XRST_PHY
VIDEO_IN /PB_XREC
XRST_PHY
2.8
TO(4/18)
XSCK XBUSY
2.5
IC4501
MODE_SW_C
30
XRST_LINK
MODE_SW_C
RB4501
100k
TRRT
Vcc
XCS
0.3
HP_JACK_IN
MODE_SW_D
RDX
FRRV
XRST_LINK
MODE_SW_B
WRX
XRST_PHY
2.8
HI_SI(MCHI)
MODE_SW_B
XRST_LINK
C4506
0.01u
B
MODE_SW_C
CAP_FWD
IC4502
AK6417AM-E2
EEPROM
LIP_SLEEP
XCS_SFD
ALE
XDVCN
XPWDA
2.8
MODE_SW_B
CAP_ON
IC4502
R4503 100k
HI_SO(HIMC)
MCDA5
DRP
XSYS_RST
R2.8/P0
XPWAD
MODE_SW_A
XPWDA
XDVCN
4
5
XCS_SFD
XPWAD
TRRT
C4501
0.001u
B
2.7
FRRV
MD0
2.8
VREF
TRRV
MD1
MODE_SW_A
RDX
MD0
XCS_SFD
WRX
VFI_OE
MCCE
XCS_SFD
MD2
2.3
TRRV
MD1
R1.2/P1.7
MCDA5
R1.8/P1.2
MCDA6
VREF
VSS
MD2
2.8
VFI_OE
SWP
IFI_VD
IFI_VD
HP_JACK_IN
37
SWP
22
HP_JACK_IN
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
TO(17/18
(CN1116))
TO(4/18,17/18
(CN1108))
TO(2/18,8/18,
17/18(CN1104))
TO(4/18,17/18
(CN1104))
131
X1
0.9
TO(11/18)
X0
29
XTAL20M
X0
1.0
113
DRUM_FG
OFR
XPWDA
MCCE
XPWDA
XPWAD
MCHA1
DEM1
XPWAD
DEM1
MCHA1
TO(15/18)
C4505
0.01u
B
R4514
100k
2.7
DRUM_FG
130
C4504
1u
B
TO(18/18)
MODE_SW_A
MODE_SW_C
120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91
DEM0
DRUM_PG
DEM0
SDC_IN
XVIDEO_IN
VSS
SDC_IN
XVIDEO_IN
MCHA0
TO(7/18)
2.2
78
XCS_TAKO
2.2
XCS_TAKO
MODE_SW_A
MODE_SW_B
R4530
470
MCHA0
AUDIO_MUTE
AUDIO_MUTE
2.8
XCS_HONEY
XCS_HONEY
TO(17/18
(CN1104))
XCS_AU
EXVSYNC
129
TO(15/18)
C4508
0.01u
B
XCS_AU
MCDA7
143
VSP_SI
0.2
VSP_SO
MCDA7
VSP_SI
XVSP_SCK
2.8
VSP_SO
VDD
TO(4/18,15/18,
17/18(CN1104))
IFI_VD
VSP_SO
XVSP_SCK
31
DRUM_PG
XVSP_SCK
TO(7/18)
FP /REELM_FG
80
133
D_2.8V
FB4501
0uH
MCDA6

NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
17
4-40
REC/PB
PB

11
10
12
14
13
15
16
VC-254 BOARD(14/18)
CAP_VS
DRUM/CAPSTAN DRIVE(MD BLOCK)
VTR_UNREG
DRUM_VS
MT_5V
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
MT_GND
DRUM_FG
DRUM_PG_SENS
FG
COM
10
M
F
FG_PG_COM
RSAT
DRUM_FG_SENS
DRUM_COM
DRUM_FG
DRUM_W
C4408
6.3V 3.3u
GND
1.4
FGOUT
26
DRUM_PG
DRUM_V
HW1
HV2
HW1
HV2
C4423
XX
B
R4423
0
C4420
1u
B
1608
FG_PG_COM
HV1
HV1
DRUM_PG_SENS
VH+
C4416
0.1u
B
HU1
CAP_V
CAP_V
10
CAP_W
11
CAP_W
12
CAP_U
13
CAP_U
14
REG_GND
15
FG2
16
FG VCC
17
R4435
R4434
10k
0.047u
C4430
2.2u
C4431
0.1u
TAPE_TOP
2012 F
TREEL_FG
116(2/2)
T_REEL_TO(11/18,13/18)
T_REEL_+
S_REEL_+
S_REEL_-
SREEL_FG
TAPE_LED_ON
TAPE_LED_ON
C4435
470p
R4436
4700
C4436
470p
CAP_PWM
DRUM_PWM
R4427
10k
C4422
XX
B
C4418
470p
B
C4426
0.01u
R4424
33k
1.2
C4432
0.01u
B
R4430
HU1
LOAD
TAPE_TOP_C
C4429
R4432
47k
HU2
HU2
UNLOAD
TAPE_END
TAPE_END_C
C4425
0.022u
B
R4417
10k
0.5%
C4415
470p
DRUM_FG_SENS B
HW2
LOAD
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
HW2
(SEE PAGE 4-52)
R4428
28
CAP_ON
VH-
GND
1.2
RLP1
1.2
RLM1
0.9~1.5
RLO1
0~2.8
RLDO1
C4434
0.001u
B
DRUM_U
CN4403 22P
R4429
LM_+
LOAD
W OUT
0
DEC2
0
DEC1
0.1
RS
0.1
OUT1
0
RFL
0.1
OUT2
0
LIMEN
2.8
LIM OUT
27
470k
FRC
3.4
FILTER
2.1
FC
2.8
RSAT
R4431
15k
PG
FG-PG_COM
29
C4428
0.047u
B
XX
GF/PG
10P
IC4401
CXA8096R-TBM
R4419
CN4402
IC4401
DRUM MOTOR DRIVE
1.3
FG IN2
1.3
FG IN
1.3
VREF
1.3
PG IN
1.1
PGC
0.1
PG OUT1
M901
DRUM MOTOR
C4433
0.001u
B
UNLOAD
NC
0.1
END OUT
1.3
END IN
1.3
TOP IN
2.8
TOP OUT
4.9
VM
8.3
VCC2
0~2.8
RLDO2
0.9~1.5
RLO2
1.2
RLM2
1.2
RLP2
NC
0.3
RSB
2
5
6
C4407
0.047u
B
30
PG OUT2
2.8
CBEN
0.4
CBIN
0.4
CBOUT
0.5
CBLOUT
1.2
DBIN
1.2
DBOUT
0.1
ISNF
XDRUM_BRAKE
C4401
0.1u B
2.8
STBY D
0.1
RF
0.4
OSC
0
SELSLP1
0
SELSLP2
3.6
VS
0.3
CSLP1
0.3
CSLP2
2.8
VCC1
2.8
XBRAKE
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
1.8
1
LM_+
LM(+)
C4424
0.1u
B
C4406 B C4405
0.022u B
0.022u
LM_LM(-)
C4404
0.1u
B
DRUM_START
CN4401 2P
C4403
0.1u B
16 15 14 13 12 11 10
MECHANISM BLOCK
(M2000)
M903
LOADING MOTOR
R4410
MODE_SW_A
MODE_SW_A
DRUM_ON
MODE_SW_B
MODE_SW_B
REG_GND
1.8
R4408
R4409
MODE_SW_C
V IN
1.8
V OUT
1.8
W IN
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
DRUM_START
MODE_SW_C
TO(18/18)
D_2.8V
DRUM_START
R4425
3300
C4413
0.1u
B
DRUM_ON
DRUM_ON
TO(11/18,13/18)
0.1u
DRUM_PG
DRUM_PG
116(1/2)
C4411
136
D4401
MA3XD21001S0
10k
RB4402
100k
CAP_FG
DRUM_FG
CAP_FG
LM_LIM_DET
CAP_FWD
CAP_FWD
C4412
0.1u
B
LM_LIM_ON
CAP_ON
CAP_ERROR
R4426 100k
CAP_ON
UNLOAD
DRUM_COM
CAP_FG
R4420 XX
CFG_DUTY
C4417
0.001u
B
TO(12/18)
TO(17/18(CN1108))
1.3
AGC
1.8
COM
1.8
U IN
1.8
U OUT
135
C4409
0.1u
B
124
R4421 XX
DRUM_U
CFG_DUTY
R4422 XX
C4419
0.001u B
C4421 0.001u B
DRUM_V
LM_-
DRUM_ERROR
DRUM_W
C4427
0.01u
B
XCC_DOWN
T_REEL_- R4447
33k
R4402
330k
XCC_DOWN
T_REEL_EVR
S_REEL_-
101
73
TO(10/18)
TO(6/18)
S_REEL_EVR
R4448
33k
TREEL_AFG
CAP_FG
Q4402
DTC144EHT2L
SWITCH
CAP_FWD
SREEL_AFG
HI8_MP_SW
R4401
47k
HI8_MP_SW
117
TO(11/18)
134
TO(13/18)
ME_SW
ME_SW
XDRUM_BRAKE
XDRUM_BRAKE
LM_LIM_ON
HU1
SREEL_FG
2.8
2.8
1.7
1.7
HV1
HU2
1.4
HV2
HW1
1.4
1.0
1.0
DRUM_8PB
RSAT
XREEL_HALL_ON
REC_PROOF_SW
Rf
0.7
Wout
1.9
VH+
0.8
VH0.7
ANGLE
Rf
0.7
Vout
RSAT
XREEL_HALL_ON
REC_PROOF_SW
NC
0.7
Uout
2.8
Vcc1
8.3
Vcc2
1.4
Vs
1
TREEL_FG
SREEL_FG
LB1991V-TLM
IC4402
LM_LIM_DET
DEW_AD
GND
FRC
Uin1
Uin2
Vin1
STBY
CAPSTAN MOTOR
DRIVE
Vin2
22
Win1
DEW
LM_LIM_DET
24 23 22 21 20 19 18 17 16 15 14 13
IC4402
MODE_SW_A
Win2
21
MODE_SW_B
1.4
20
M-SW(A)
MODE_SW_C
FGin+
M-SW(B)
R4405 100k
1.4
19
FGin-
18
FGout
FG1
M-SW(C)
R4453
1M
1.4
HW2
LM_LIM_ON
CFG_DUTY
TREEL_FG
10 11 12
R4449
39k
C4442
0.1u
B
C4437
0.1u
B
C4438
0.1u B
CN4404 15P
(SEE PAGE 4-52)
C_LOCK_SW
HI8_MP
REC_PROOF
ME/MP
HALL_COM
T_REEL(-)
T_REEL(+)
SENSOR_VCC
S_REEL(+)
S_REEL(-)
10
REG_GND
11
TAPE_LED(A)
12
TAPE_LED(K)
13
TAPE_END(C)
14
TAPE_TOP(C)
15
XCC_DOWN
HI8_MP_SW
REC_PROOF_SW
R4411
82
2012
ME_SW
R4414
270
T_REEL_+
R4407
470
S_REEL_+
C4402
0.1u
B
C4410
0.1u
B
R4416
0 4700
C4414
220p
B
Q4401
2SC4738F-Y/GR(TPL3)
LED DRIVE
S_REEL_-
C4441
0.1u B
C4440
0.1u
B
R4452
2.2
R4451
2.2
R4450
2.2
SIGNAL PATH
REC
4.1
T_REEL_-
0.47u F
TAPE_LED_ON
XREEL_HALL_ON
C4439
REC/PB
PB
Drum speed servo

Drum phase servo
Capstan speed servo
TAPE_END_C
TAPE_TOP_C
16
4-41
4-42
DRUM/CAPSTAN DRIVE
VC-254 (14/18)

VC-254 BOARD(15/18)
AUDIO PROCESS(AU BLOCK)
10
11
12
13
14
15
16
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
AU_4.75V
4.7
AU_2.8V
R5745
10k
2.3
BPF_MONI
R5746
10k
2.3
PB_RF
AUDIO_R_I/O
0
C5704
10u
6.3V
MUTE
0
0
Q5708
RN2111F(TPL3)
SWITCH
C5705 22u
4V
C5706 10u 4V
C5703
0.22u B
R5709
47k
R5710
10k
MIC_L
R5714
47k
TO(16/18)
C5713
0.47u
B
MIC_R
R5715
10k
R5730
820
C5750
10u
4V
C5715
3.3u
4V
SCLK
MCLK
LRCK
SDTI
VDD
DEM0
DEM1
SDTO
C5743
0.001u B
C5744
0.01u
B
C5745
B
0.01u
XCS_AU
C5749
68p
CH
0.7
2.8
2.8
DATA_TO_SFD
C5751
10u
4V
L5701
10uH
2520
C5752
0.01u
B
C5754
0.22u
B
1608
R5731
470
XPWDA
XPWAD
C5756
0.22u
B
TO(13/18)
XVSP_SCK
VSP_SO
VSP_SI
R5733
470k
R5732
470
C5755
6800p
B
C5757
6800p
B
VSP_SI
VSP_SO
XVSP_SCK
VSP_SI
VSP_SO
31
TO(13/18)
XVSP_SCK
XCS_AU
143
TO(13/18)
126
TO(12/18)
AU_BPF
1.5M_DEV
10 11 12 13 14 15 16
C5724
0.22u
B
130
DEM1
DEM0
1.7M_DEV
SIGNAL PATH
PB
16
4-43
TO(4/18)
SFD_FCK
SFD_LRCK
DATA_FROM_SFD
REC
VC-254 (15/18)
40
SFD_BCK
C5753
0.01u
B
AUDIO
SIGNAL
AUDIO PROCESS
TO(9/18)
0.7
XPWAD
VSS
XMIC_MONO
1.4
0.9
1.4
2.8
2.8
1.2
XPWDA
C5748
B
0.01u
R5728
XX
C5740
0.22u
B
AINL
1u B
1.2
0.22u B
C5736
C5738
1
1.2
1.2
R5725
470k
C5747
0.47u B
C5742
B
0.001u
IC5702
AOUTR
AK4550VT-E2
AOUTL
1u B
0.1u B
C5735
1u B
C5733
0.22u B
R5720
150k
141
C5746
0.47u
B
XCS_AU
C5709
0.22u
B
Q5718
UP04216008S0
36
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
TO(7/18)
IC5701
CXA3284R-T6
1u B
76
R5707
1k
R5708
1k
C5701
10u 4V
C5702
10u 4V
AUDIO_L_I/O
C5739
IR_R
AUDIO IN/OUT,
AUDIO PROCESS
1u B
1u B
IR_L
TO(12/18)
HP_GND
2.3
HP_R
2.3
IR_OUT_L
2.3
IR_OUT_R
2.3
LINE_OUT_L
1.3
LINE_OUT_R
0
MUTE_OUT
4.7
VCCH
2.3
VREFH
1.1
VREF
1.3
MIC_IN_L
1.4
LINE_IN_L
C5734
C5737
C5712
47u 4V
C5741
0.22u
B
R5724
470k
16 15 14 13 12 11 10
RF_GND
0.1
IFDC_L
0.1
IFDC_R
0.1
FSC
0.1
RFDC_L
0.1
RFDC_R
R5712
100
HP_R_OUT
IC5701
47k
TO(17/18
CN1116))
R5743
10k
1u B
HP_L_OUT
R5721
R5711
100
SP_GND
2.8
SP2.3
HP_L
C5732
C5711
47u 4V
FADER
1.2
IREF
0.1
PLL_LOOP_L
0.1
PLL_LOOP_R
R0.1/P0.2
MUTE_TC
R0.5/P0.7
RECFM_OUT/BPF_MONI
1.9
BPF_ADJ
0.1
ST/MONO_TC
0.1
PB_RF_IN
1.5
RF_AGC_TC
2.8
RF_SWP
2.8
CS_IN
2.7
CK_IN
0.3
SI_IN
2.5
MONO_OUT(SO)
1.7
MIC_MONO
1.8
DEV_L
1.6
DEV_R
AU_GND
1.4
PB_IN_L
1.4
PB_IN_R
2.9
SP+
C5722
0.22u B
R5742
10k
0
AGCTC
1.4
MIC_IN_R
1.4
LINE_IN_R
1.4
REC_OUT_L
1.4
REC_OUT_R
4.9
SP_VCC
2.4
SP_VREF
2.4
BEEP_IN
1.2
SP_IN
0.1
SP_SIG
2.3
SP_OUT
0.1
CTLPF
2.8
VCC
0.8
TC_R
0.3
TCH_R
0.1
NRDC_R
0.1
WEIGHT_R
0.7
TC_L
0.2
TCH_L
0.1
NRDC_L
0.1
WEIGHT_L
C5710
0.01u
B
C5708
XX
Q5717
UP04216008S0
MUTE
128
C5730
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
SPC5707
XX
140
C5731
SP+
C5717
0.22u
C5719
0.22u
TO(17/18
CN1117))
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
139
1u B
0.1u B
C5716
10u
6.3V
C5718
C5714
10u
6.3V
C5728
C5758
0.22u
B
C5725
R5717
1k
TRV330/
TRV530
0.22u B
A/D,D/A
CONVERTER
2200p B
KASYAON
0.22u B
TO(17/18
CN1104))
89
IC5702
R5719
*
C5720
138
R5719
82k: TRV230
68k; TRV330/TRV530
C5759
C5721
TO(10/18)
BEEP
0.22u B
111
AINR
R5718
*
REG_GND
VCOM
R5718
15k: TRV230
47k; TRV330/TRV530
TO(17/18
(CN1108))
C5723
22u
4V
1.8
1.2
Q5716
UP04501008S0
BUFFER
R5744
47k
MT_5V
1.8
TO(18/18)
R5747
47k
137
142
4-44
VC_RF_SWP
71
TO(11/18)
AFM_FSC
19
TO(2/18)

11
10
12
VC-254 BOARD(16/18)
A
MIC AMP(MA BLOCK)

REG_GND
AU_2.8V
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
TO(18/18)
TO(12/18)
SHOE_MIC_L
R5801
33k
C5826
0.047u
B
EXT_MIC_R
EXT_MIC_L
147
R5807
6800
R5802
18k
C5822
0.1u
B
R5809
2200
R5823
1200
C5832
0.022u
B
R5824
0
C5833
1500p
B
R5819
9100
R5827
6800
R5817
2200
C5821
XX
C5806 C5813
0.01u 100p
CH
B
C5830
0.047u
B
R5820
7500
R5815
1k
C5820
100p
CH
ZOOM_MIC_CONT
ZOOM_MIC_CONT
125
EXT_MIC_DET
EXT_MIC_DET
97
MIC_R
MIC_R
XMIC_MONO
XMIC_MONO
MIC_L
MIC_L
SHOE_MIC_L
SHOE_MIC_L
TO(10/18)
141
TO(15/18)
148
TO(17/18(CN1101))
C5824
0.1u
B
C5817
0.001u
B
1.4
1.4
1.4
1.4
1.4
1.3
1.4
2.1
IC5801
ZOOM_AMP_IN
NC/GND
R0/P0.1
NC/L_BIAS
R0/P0.1
NC/R_BIAS
ZOOM_BAL
ZOOM_POSI
MIC AMP
VCC
C/NC
IC5801
MIX_OUT
EXT_MIC
AN2901FHQ-EB
GND
HPF_ON/OFF
R_OUT
MTX_AMP_IN_R
1.4
1.4
1.4
HPF_AMP_IN_R
SUB_SIG_OUT_R
HPF_OUT_R
INVT_OUT_R
MTX_AMP_OUT_R
SG_IN_R
1.4
C5809
0.01u
B
NC/VCC
C5841
1u
1608
B
R5846
XX
1.4
MIC_L
1.7
XMIC_MONO
R5834
10k
2.6
2.3
2.8
2.5
2.7
C5839
C5838
0.1u B
C5840
0.22u
22u
4V
R5831
0
ZOOM_MIC_CONT
R5830
XX
1.8
EXT_MIC_DET
1.4
0
R5829
33k
MIC_R
SIGNAL PATH
10 11 12
AUDIO
SIGNAL
1.4
AMP_OUT_R
SUB_IN_R
1.4
MODE_CTL_1
C_1/2VCC
13 14 15 16 17 18 19 20 21 22 23 24
HPF_OUT_L
MTX_AMP_OUT_L
SUB_SIG_OUT_L
MTX_AMP_IN_L
SG_IN_L
INVT_OUT_L
AMP_OUT_L
MODE_CTL_2
MIC_MONO
1.4
R5803
2200
EXT_IN_L
ZOOM_AMP_OUT
C5808
0.022u
B
REG_2.5V
L_OUT
EXT_IN_R
1.4
NC/SUB_BIAS
2.1
1.4
HPF_AMP_IN_L
NC/VCC
1.4
1.4
1.4
C5815
10u 4V
INT_IN_L
SUB_IN_L
1.4
L5803
68uH
2016
GND
REG_2.5V
C_REG
INT_IN_R
1.2
2.3
C5842
XX
R5805
4700
C5810
0.01u
B
R5847
XX
C5843
XX
C5844
XX
36 35 34 33 32 31 30 29 28 27 26 25
48 47 46 45 44 43 42 41 40 39 38 37
R5806
10k
C5812
10u
4V
TO(17/18(CN1116))
2.3
1.4
C5807
0.022u
B
146
1.4
INT_MIC_L
INT_MIC_R
C5814
0.001u
B
C5816
100p
CH
C5818
XX
R5818
2200
C5823
C5819
100p CH 0.1u
R5816
1k
R5814
6800
C5827
0.047u
B
16
REC
C5825
0.1u
B
PB
R5822
7500
C5829
0.047u
B
R5828
6800
R5821
9100
R5825
0
C5835
1500p B
R5826
1200
C5836
0.022u
B
4-45
4-46
MIC AMP
VC-254 (16/18)

3
10
VC-254 BOARD(17/18)
TO PC-082 BOARD(3/3) CN1901

(DCR-TRV330/TRV530)
CONNECTOR(CN BLOCK)
SHOE_MIC_L
SHOE_CONT_AD
SHOE_MIC_GND
SHOE_ID2
12
RXD
13
STB_ON
115
PC_1.9V
PC_1.9V
VFI_C3
VFIO_C4
37
TO(4/18,
13/18)
26
MF_A
25
MF_A
MF_B
VFIO_C5
VFIO_C6
VFIO_C6
VFIO_C7
VFIO_C7
VFI_HD
VFI_HD
VFI_VD
VFI_OE
VFI_VD
VFI_VD
VFI_OE
VFI_OE
IFI_Y6
IFI_Y7
IFI_C0
IFI_C1
IFI_C2
IFI_C3
IFI_C4
IFI_C5
IFI_C6
IFI_C7
IFI_HD
IFI_Y4
IFI_Y6
IFI_Y5
IFI_Y7
IFI_Y6
IFI_C0
IFI_Y7
IFI_C1
IFI_C0
IFI_C2
IFI_C1
IFI_C3
IFI_C2
IFI_C4
IFI_C3
IFI_C5
IFI_C4
IFI_C6
IFI_C5
IFI_C7
IFI_C6
IFI_HD
IFI_C7
R1146
*
IFI_C7
IFI_C6
IFI_C5
IFI_C4
IFI_C3
IFI_C2
IFI_C1
112
TO(10/18)
REG_GND
REG_GND
99
100
REG_GND
REG_GND
98
REG_GND
97
MS_LED
96
XDS_FLASH_RST
DS_MAD
TO(2/18)
142
TO(15/18)
TO(11/18)
31
TO(1/18,
2/18,5/18,
8/18)
42
TO(13/18)
110
86
41
TO(10/18)
TO(8/18)
TO(4/18,
8/18)
TO(4/18)
85
IFI_VD
21
TO(2/18,8/18)
22
TO(2/18,8/18)
EXT_MIC_R
EXT_MIC_L
EXT_MIC_L
TO(4/18)
TO(10/18)
SE_GND
SE_2.8V
45
95
LIA1
LIA1
TO(5/18)
132
114
70
TO(13/18)
TO(4/18)
135
TO(14/18)
120
TO(11/18)
100
CN1117
45P
REG_GND
VTR_UNREG
LCD_LED_ON
EVER_3.0V
XOSD_SCK
OSD_SO
LCD_COM/XDATA
BATT_LI_3V
REG_GND
SP_-
SP_+
REG_GND
DIAL_B
DIAL_A
MS_LED
XHI_RESET
KEY_AD4
KEY_AD3
KEY_AD2
KEY_AD0
KEY_AD1
XIR_LED_ON
D_2.8V
EVF_DD_ON
EVF_4.75V
XTALLY_LED
VB
VR
VG
VCO
XSYS_RST
HI_SO
XHI_SCK
XCS_EVF
PANEL_XVD
PANEL_XHD
EVF_R
BW_Y
EVF_B
EVF_13.3V
EVF_2.8V
REG_GND
REG_GND
AUDIO
SIGNAL
XCS_LCD_DRIVER
Y/CHROMA
REC
PB
TO CF-079/080 BOARD(1/2) CN102
(THROUGH THE FFC-001 FLAT CABLE)
(SEE PAGE 4-75)
16
4-47
EVF_VB
11
VCO
12
EVF_VG
13
DV_RF_SWP
14
RF_IN
15
CAP_FG
16
RF_MON
17
TMS
18
TCK
19
TDO
20
TDI
INIT_CHARGE_ON
ZOOM_VR_AD
BATT_SIG
BATT_SIG
DV_RF_SWP
TDO
CPC
(FOR CHECK)
TO(10/18)
TO(10/18)
ZOOM_VR_AD
FAST_CHARGE
CN1113
FAST_CHARGE
SHOE_ON
SHOE_ON
BATT/XEXT_SW
BATT/XEXT_SW
XS/S_SW
XS/S_SW
XCAM_MODE_SW
XCAM_MODE_SW
XVTR_MODE_SW
XVTR_MODE_SW
XEJECT_SW
XEJECT_SW
XPHOTO_STBY_SW
10
XPHOTO_STBY_SW
11
KEY_AD1
12
XPHOTO_FREEZE
13
D_2.8V
14
INIT_CHARGE_ON
15
BATT_UNREG
VTR_UNREG
16
BATT_UNREG
C/D_VS_D1.5V
17
C/D_VS_D1.5V
18
C/D_VS_D1.5V
19
C/D_VS_D1.5V
BATT_UNREG
TO(10/18)
R1144
4700
CAP_FG
BL_REG_UNREG
20
C/D_VS_D1.5V
21
BL_REG_UNREG
22
BL_REG_UNREG
23
BL_REG_UNREG
24
BL_REG_UNREG
25
VTR_UNREG
26
VTR_UNREG
27
VTR_UNREG
28
VTR_UNREG
29
SHOE_GND
30
SHOE/PRT_UNREG
31
SHOE_GND
32
SHOE/PRT_UNREG
33
SHOE_GND
34
SHOE/PRT_UNREG
35
SHOE_GND
TO(18/18)
REG_GND
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
REG_GND
VIDEO SIGNAL
EVF_VR
10
VTR_UNREG
PRT_HEAD_UNREG
VC_RF_SWP
EVF_G/BW_Y
SIGNAL PATH
CHROMA
TO(6/18)
105
SHOE/PRT-SIG/MT_UNREG
RF_AGC_OUT
VC_RF_SWP
RF_IN
TO(11/18)
EVER_3.0V
XOSD_SCK
OSD_SO
TO(10/18)
LCD_COM/XDATA
103
XCS_LCD_DRIVER
VTR_UNREG
SIRCS_SIG
XF_TALLY_LED
LCD_LED_ON
VREF2
XCS_EVF
LIA2
TO(11/18)
PANEL_XVD
VG
149
PANEL_XHD
LIA2
VREF2
XF_TALLY_LED
122
REG_GND
RF_ENV
59
TO(10/18)
EXT_MIC_R
109
10
VREF1
PB_RF
VCO
TO(5/18,10/18)
TALLY_LED
TO(10/18)
TO(16/18)
TO(15/18)
108
146
139
11
SP-
AU_GND
F0_ADJ_RF_IN
0.3
SP+
INT_MIC_R
Q1104
DTC144EHT2L
LED DRIVE
BATT_LI_3V
12
XHI_SCK
DIAL_B
INT_MIC_R
TO(5/18,8/18,
10/18,11/18,13/18)
BPF_MONI
XPHOTO_FREEZE
DIAL_A
INT_MIC_L
63
PB_RF
VB
HI_SO
HI_XRESET
13
TO(12/18)
TO(11/18)
R1124
1k
TO(10/18)
INT_MIC_L
XSYS_RST
106
14
TO(5/18,8/18,
10/18,11/18,13/18)
KEY_AD4
REG_GND
58
KEY_AD3
15
145
KEY_AD2
SE_2.8V
IR_DRV_EM
KEY_AD1
16
KEY_AD0
IR_DRV_EM
XIR_LED_ON
17
EVF_DD_ON
SIRCS_SIG
BPF_MONI
F0_ADJ_RF_IN
20P
TO(9/18)
107
TO(18/18)
REG_GND
TO(15/18)
AFC_FO
RF_MON
123
18
140
SWP
TO(8/18)
EVF_BL_4.75V
HP_GND
TO(13/18)
VB
HP_L_OUT
131
SFD_LRCK
SFD_BCK
XCS_DS
TD_2-3
TCK
TMS
VSP_SI
VSP_SO
XVSP_SCK
SPCK
33
TO(4/18,
8/18)
SWP
AFC_F0
VR
44
VR
HP_R_OUT
19
IFI_C0
138
VG
HP_JACK_IN
HP_L
VREF1
TO(4/18,13/18)
71
IFI_OE
IFI_VD
IFI_OE
TO(2/18,8/18)
TO(15/18)
IFI_HD
IFI_OE
IFI_VD
20
SSS_FROM_VC
IFI_Y5
AFCK
IFI_Y4
IFI_Y3
MS_IN
IFI_Y2
USB_DET
IFI_Y3
XWEN_FROM_VC
IFI_Y5
IFI_Y1
DS_RESETM
IFI_Y4
IFI_Y2
MF_LED
55
VC-254 (17/18)
95
RTS/IR_L
ADAO2
VFIO_C7
VFIO_C6
VFIO_C5
VFIO_C4
VFI_C3
VFI_C2
VFI_C1
VFI_C0
VFO_Y7
VFO_Y6
VFO_Y5
VFO_Y4
VFO_Y3
VFO_Y2
VFO_Y1
VFO_Y0
VFI_Y7
VFO_OE
VFI_Y6
IFI_Y3
IFI_Y0
R1105-R1123
XX
(DCR-TRV330/TRV530)
R1105-R1123
0
(DCR-TRV230)
CONNECTOR
94
ADAI2
CTS
SSS_FROM_L
86
93
XWEN_FROM_L
85
TXD/IR_R
SSS_FROM_VC
84
91
XWEN_FROM_VC
83
90
A_4.75V
82
92
D_2.8V
81
USB_DET
D_2.8V
80
RXD
REG_GND
79
AUDIO_MUTE
REG_GND
78
89
VSP_SI
77
88
SFD_LRCK
76
87
SFD_BCK
75
XSYS_RST
74
HI_SO
73
XCS_DS
69
D_1.5V
HI_SI
68
PC_1.9V
XDS_WAKE_UP
67
PC_1.9V
XHI_SCK
66
72
XCS_HONEY
65
71
VFIO_C7
64
70
TD_2-3
IFI_C1
63
KASYAON
42
VFIO_C6
IFI_C0
41
62
IFI_HD
40
XVSP_SCK
VFI_C3
39
61
IFI_VD
38
VFIO_C5
VFI_C2
37
60
IFI_OE
36
TMS
VFI_C1
35
59
IFI_Y7
34
VFIO_C4
VFI_C0
33
58
IFI_Y6
32
TCK
VFO_Y7
31
57
IFI_Y5
30
IFI_C7
VFO_Y6
29
56
IFI_Y4
28
VSP_SO
VFO_Y5
27
55
IFI_Y3
26
IFI_C6
VFO_Y4
25
54
IFI_Y2
24
53
VFO_Y3
23
52
IFI_Y1
22
MS_IN
VFO_Y2
21
TDI
IFI_Y0
20
IFI_C5
VFO_Y1
19
51
VFI_Y7
18
IFI_C4
VFO_Y0
17
50
VFI_Y6
16
SPCK0
VFO_OE
15
49
VFI_Y5
14
IFI_C3
VFI_OE
13
48
VFI_Y4
12
47
VFO_VD
11
46
VFI_Y3
10
DS_RESETM
VFI_VD
AFCK
VFI_Y2
IFI_C2
VFO_HD
45
VFI_Y1
44
VFI_HD
43
VFI_Y0
VFIO_C5
IFI_Y2
IFI_Y1
VCO
20
121
VFIO_C4
VFIO_C4
VFI_HD
REG_GND
VFI_C3
VFI_C3
VFIO_C7
26P
VFI_C2
VFI_C2
VFIO_C6
VFI_C1
VFI_C1
VFIO_C5
REG_GND
VFI_C0
VFI_C0
VFI_C1
EP_2.8V
VFI_Y7
VFI_Y7
VFI_Y7
EP_13.3V
VFI_Y6
VFI_Y6
VFI_C2
TO(18/18)
VFI_Y5
VFI_Y5
VFI_C0
TO(4/18)
VFI_Y4
VFI_Y4
IFI_Y0
IFI_Y1
D_1.5V
D_1.5v
HP_R
29
17
88
IFI_Y0
PC_1.9V
D_1.5V
VFI_Y3
VFI_Y3
VFI_Y6
36
D_2.8V
VFI_Y2
VFI_Y2
VFI_Y4
A_4.75V
VFI_Y1
VFI_Y1
VFI_Y3
R1105
*
R1106
*
R1107
*
R1108
*
R1109
*
R1110
*
R1111
*
R1112
*
R1113
*
R1114
*
R1115
*
R1116
*
R1117
*
R1118
*
R1119
*
R1120
*
R1121
*
R1122
*
R1123
*
KASYAON
C1102
0.1u
B
VFI_Y0
VFI_Y0
VFI_Y5
21
CN1108
R1134,1145,1146
0
(DCR-TRV230)
XX
(DCR-TRV330/TRV530)
HOTSHOE_ID2
20
HP_JACK_IN
TO(4/18)
R1149
XX
R1145
*
SHOE/PRT-SIG/MT_UNREG
VFI_Y2
TO(10/18)
IFI_HD
104
IFI_VD
SHOE_CONT_AD
IFI_OE
PRT_HEAD_UNREG
IFI_Y7
19
IFI_Y6
18
SHOE/PRT_UNREG
IFI_Y5
PRT_HEAD_UNREG
IFI_Y4
HOTSHOE_ID1
22
R1134
*
IFI_Y3
17
R1155
100
IFI_Y2
PRT_HEAD_UNREG
23
34
XWEN_FROM_L
IFI_Y1
LANC_SIG
24
TO(13/18)
AUDIO_MUTE
TO(4/18)
R1147
0
16
MF_B
TO(4/18)
129
IR_L
15
MF_LED
TO(8/18,10/18,
11/18,13/18)
39
IR_R
14
A_4.75V
TO(10/18)
83
ADAI2
R1148
0
TO(11/18)
98
R1150
XX
TXD
AU_GND
ADAO2
R1154
100
SHOE_ID1
CN1116
HI_SI
SSS_FROM_L
LANC_SIG
REG_GND
35
C1101
0.1u
B
(SEE PAGE 4-82)
22
21
XDS_WAKE_UP
VFI_Y1
(THROUGH THE
FP-266 FLEXIBLE)
20
(SEE PAGE 4-63)
TO(16/18)
VFI_Y0
19
XCS_HONEY
RTSSCK
SHOE/PRT_UNREG
148
IFI_Y0
SHOE_MIC_L
R1151
100
R1152
100
10 R1153
100
11
STB_ON
TO
SI-028/029 BOARD
CN304
(DCR-TRV230/
TRV330)
(DCR-TRV530)
18
DS_MAD
VFI_Y5
CTSHDS
17
XDS_FLASH_RST
VFI_OE
SHOE_MT_GND
FP-264
FLEXIBLE
151
16
(DCR-TRV230)
(DCR-TRV330/TRV530)
VFO_VD
VFI_Y4
SHOE_MT_GND
D1106
XX
OUDZS.TE17-8.2B
VFI_Y3
D1106
*
VFI_VD
SHOE_UNREG_GND
D1105
*
VFO_HD
VFI_Y2
D1102
*
VFI_HD
SHOE_UNREG_GND
15
(DCR-TRV230)
(DCR-TRV330/TRV530)
VFI_Y1
REG_GND
CN1104
20P
SHOE_UNREG_GND
D1102,1105
XX
O1ZA8.2(TPL3)
VFI_Y0
CN1101
D1101
01ZA8.2(TPL3)
C1104
0.1u
B
D1103
01ZA8.2(TPL3)
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
INTELLIGENT
ACCESARY
SHOE
14
100P
13
12
11
4-48
36
PRT_HEAD_UNREG
37
REG_GND
38
PRT_HEAD_UNREG
39
REG_GND
40
PRT_HEAD_UNREG
41
REG_GND
42
REG_GND
43
REG_GND
44
REG_GND
45
REG_GND
46
REG_GND
47
REG_GND
48
REG_GND
48P
TO FU-150/154 BOARD
CN403
(DCR-TRV230/TRV330)
(DCR-TRV530)
(SEE PAGE 4-102)

2
3
1
10
12
11
13
14
16
15
17
18
19
20
VC-254 BOARD(18/18)
A
DC/DC CONV.(DD BLOCK)

CAM_15V
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
CAM_-7.5V
A_4.75V
A_4.75V
A_2.8V
BL_GND
A_2.8V
BL_REG
D_2.8V
BL_CONT
CAM_DD_ON
BL_REG_UNREG
(CN1113))
7.9 2
4.2
L1317
22uH
C/D_VS_D1.5V
VTR_UNREG
REG_GND
L1318
4.7uH
A_4.75V
Q1309
CPH6702-TL
SWITCHING
REG_GND
C1347
10u
10V
C1344
4.7u
10V
B
C1332
4.7u
10V
B
R1350
0
D_1.9V
149 TO(17/18
8.3 1
PC_1.9V
1 TO(1/18)
D_2.8V
65 TO(5/18)
A_2.8V
13 TO(2/18)
D_2.8V
D_1.5V
REG_GND
MT_GND
REG_GND
A_4.75V
VTR_UNREG
D_2.8V
MT_5V
D_2.8V
136 TO(14/18)
25 TO(3/18)
MT_5V
DRUM_VS
MT_GND
CAP_VS
REG_GND
MT_5V
A_2.8V
CAP_ERROR
D_2.8V
D_1.9V
DRUM_ERROR
28 TO(4/18)
D_1.9V
D_1.5V
BOOT_CAP_H-4
VREF
MOS_GATE-4
OUTPUT_GND-1,2,3
STANDBY-3
BOOT_CAP_H-3
STANDBY
BOOT_CAP_L-3
BOOT_CAP_H-2
C1306
0.01u
B
R1306
15k
OUTPUT-3
BOOT_CAP_L-2
FEED_BACK-3
OUTPUT_
VCC-1,2,3
C1313
0.001u
B
8.3
6.6
7.9
8.0
6.9
8.5
2.2
1.4
2.8
1.5
0.9
4.7
R1311
22k
C1311
1500p B
R1313
8200
1.5
1.1
1.5
13.4
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
C1309
680p
B
R1346
XX
R1347
22k
0.5%
C1361
XX
C1350
10u
16V
R0.5/P0
R1332
220k 0.5%
R1327
22k
4.7
Q1321
2SC4738F-Y/GR(TPL3)
SWITCHNG
R1333
47k
EP_2.8V
R1339
39k
0.5%
PANEL_4.75V
REG_GND
A_2.8V
RP_6.0V
67 TO(6/18)
RP_4.75V
C1352
0.1u
B
64 TO(5/18)
PANEL_4.75V
C1354
10u 20V
R1322
10k
0.5%
1.0
R1318
4700
EP_2.8V
PANEL_-15.3V
PANEL_-15.3V
4.2
1.5
EP_13.3V
R1338
100k
0.5%
15.4
4.7
R0/P-0.3
4.9
R1323
Q1329 100k
UP04401008S0
60 TO(5/18)
REG_GND
EP_13.3V
R1334
100k
Q1328
UP04501008S0
R1330
100k
0.5%
R-9.9/
P-10.3
1.5
Q1327
UP04501008S0
L1304
22uH
C1348
10u
6.3V
R1321
22k
0.5%
7.4
Q1312
2SA1774HT2L
C1330
4.7u
10V
Q1303
CPH6702-TL
2.0
L1305
22uH
L1310
4.7uH
R1340
7500
RP_4.75V
REG_GND
81 TO(7/18)
D_2.8V
L1319
4.7uH
TRV330/TRV530
C1318
0.001u
B
L1302
22uH
6.8
Q1304,1307
SWITCHING
EP_2.8V
C1340
10u
6.3V
C1336
22u
6.3V
C1333
22u
6.3V
1.3
4.7
0.6
0.6
R1366
150
C1363
2200p
B
R1365
1k
R1364
22k
D1302
1SS383(T5RSONY1)
0.1
5
T1301
CONVERTER
TRANSFORMER
4
8.0
C1337
4.7u
F
R1319
47k
-2.2
R1369
100k
R1345
0
C1338
4.7u
F
8.3 1
7.9 2
3
C1323
4.7u
10V
B
4.7
L1301
33uH
C1326
4.7u
10V
B
RP_4.75V
87 TO(9/18)
A_2.8V
REG_GND
R1342
*
Q1330
*
C1355
*
D_2.8V
R1343
*
REG_GND
A_2.8V
EP_13.3V
118 TO(11/18)
D_2.8V
REG_GND
144 TO(12/18)
AU_2.8V
C1356
2.2u
F
IC1303
R1320
22k
A_2.8V
AU_2.8V
REG_GND
D_2.8V
133 TO(13/18)
REG_GND
+6V REG
AU_4.75V
5.9
R7.5/
P8.1
C1358
XX
AU_4.75V
AU_2.8V
C1357
10u
10V
137 TO(15/18)
MT_5V
REG_GND
EVF_BL_4.75V
EVF_BL_4.75V
123 TO(17/18(CN1117))
PC_1.9V
150 TO(17/18(CN1104))
PC_1.9V
SIGNAL PATH
L1312
XX
L1313
4.7uH
L1314
4.7uH
L1315
4.7uH
PANEL_4.75V
L1316
22uH
RP_4.75V
A_4.75V
REC
EVF_BL_4.75V
AU_4.75V
R1349
0
93 TO(10/18)
VTR_DD_ON
R1337
*
C1342
*
A_4.75V
REC/PB
PB
D_2.8V
D_1.5V
PC_1.9V
151 TO(17/18)
EP_13.3V
EP_2.8V
REG_GND
C1335
10u
6.3V
C1339
10u
6.3V
C1341
10u
6.3V
C1345
10u
6.3V
Q1302
CPH6702-TL
SWITCHING
R1310
27k
0.5%
RP_4.75V
R1341
*
A_4.75V
C1360
0.1u
B
C1328
*
D1301
*
Q1324
*
R1335
*
IC1303
RN5RZ59BA-TL
1.4
C1362
2.2u
F
D1305
*
PANEL_-15.3V
1.5V REG
A_4.75V
REG_GND
L1320
4.7uH
Q1314
DTC144EHT2L
EMERGENCY
DETECT
C1359
4.7u
F
82 TO(8/18)
D_2.8V
R1362 C1322
100k
10u
0.5%
4V
Q1333
2SC4738F-Y/GR(TPL3)
EP 13.3V REG
R1370
*
A_2.8V
PANEL_-15.3V_REG
13.5
D1306
1SS383(T5RSONY1)
Q1301
CPH6102-TL
SWITCHING
IC1304
R1356
47
R1361
0
8.3
A_4.75V
Q1324,1330
PANEL-15.3V REG
CAM_DD_ON
C1343
10u
6.3V
8.0
C1315
0.001u
B
R1355
47k
1
AU_2.8V
L1309
22uH
C1327
4.7u
10V
B
Q1307
SI2304DS-T1
C1319
0.001u
B
A_2.8V
L1308
22uH
2.2
8.4
D_2.8V
L1307
4.7uH
Q1332
2SC4738F-Y/GR(TPL3)
8.0 2
7.1
2.9
L1306
4.7uH
Q1331,1332
D1.5V REG
1.56V
R1363
3900 0.5%
8.1
2.7
R1367
XX
1.5
6
Q1331
FMMT717TA
1.9
1.55
R1368
XX
Q1304
CPH6702-TL
C1320
10u
4V
8.3 1
C1334
10u
4V
A
Q1308
SI2304DS-T1
8.0
8.6
C1331
4.7u
10V
B
3216
2.7
6.9
Q1303,1308
SWITCHING
1.5
8.5
B
0.001u
C1316
8.7
B
0.001u
C1317
7.2
A_4.75V
1
R1360
0
R1317
47k
D_2.8V
Q1323,1328
CAM 15V REG
Q1323
2SA1774HT2L
16.0
14.9
Q1316
2SC4738F-Y/GR(TPL3)
R-7.6/P0.4
-10.5
7.8
3.5
2.9
BOOT_CAP_L-4
SOFT_START
STANDBY-7
C1329
4.7u
10V
B
8.2
8.3
OUTPUT-4
VCC
L1303
22uH
REG_GND
OUTPUT-5
CXA3057R-T6
GND
8.0 2
8.1 2
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
51
IC1301
MOS_DUTY
8.3 1
Q1306
CPH6702-TL
SWITCHING
6
A_4.75V
IC1304
TA75S01F(TE85R)
7.9
6.6
8.3
8.3
OUTPUT_VCC
-4,5,6
OUTPUT-7
BOOT_CAP_L-7
8.3
OUTPUT_VCC-7
NONINV_INPUT-7
OUTPUT_MONITOR-7
BOOT_CAP_H-7
4.2
1.0
R1314
22k
R1358
0
INV_INPUT-7
FEED_BACK-7
OUTPUT_MONITOR-6
INV_INPUT-6
NONINV_INPUT-6
FEED_BACK-6
SCP
Q1316,1329
CAM-7.5V REG
R1316
0
A_4.75V
8.3 1
BOOT_CAP_L-5
OUTPUT-2
0.9
52
BOOT_CAP_H-5
DC/DC CONVERTER
OUTPUT-1
1.4
CT
1.4
OUTPUT-6
BOOT_CAP_L-1
2.9
BOOT_CAP_L-6
BOOT_CAP_H-1
2.9
IC1301
RT
MOS_GATE-1
8.3
8.1 2
OUTPUT_GND-4,5,6,7
COMP
1.5
FEED_BACK-4
OUTPUT_MONITOR-1
1.5
C1314
470p
B
BOOT_CAP_H-6
INV_INPUT-1
C1321
4.7u
10V
B
INV_INPUT-4
FEED_BACK-1
1.2
OUTPUT_MONITOR-4
OUTPUT_MONITOR-2
0.8
2.1
C1303
0.1u B
NONINV_INPUT-5
INV_INPUT-5
0.8
FEED_BACK-5
INV_INPUT-2
C1305
0.047u
B
C1302
0.1u
B
1.4
FEED_BACK-2
2.0
OUTPUT_MONITOR-3
R1307
6800
C1307
4700p
B
R1301
22k
C1301
220p
B
C1304
0.1u
B
R1302
33k
0.9
INV_INPUT-3
R1303
56k
0.5%
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
OUTPUT_MONITOR-5
16 15 14 13 12 11 10
1.1
R1312
4700
R1357
0
C1312
2200p
B
1.0
1.3
0.4
0.5
0.8
1.2
R1309
10k
3.5
C1308
2200p
B
R1305
0
1.2
R1359
0
C1310
4700p
B
ET133
8.3 1
R1348
10k
0.5%
C1324
XX
B
14.3
ET132
Q1305
CPH6702-TL
SWITCHING
6
12.8
R1304
33k
R1326
10k
ET131
R1331
10k
REG_GND
R1336
22k
Q1311,1312,13127
MT 5V REG
Q1311
2SB798-T1-DLDK
8.3
4.9
AU_2.8V
147 TO(16/18)
REG_GND
C1346
XX
6.3V
*MARKED:MOUNT TABLE
REF.NO.
DCR-TRV230/
TRV330
DCR-TRV530
C1328
C1342
C1355
D1301
D1305
Q1324
Q1330
R1335
R1337
R1341
R1342
R1343
R1370
0.01u
0.1u
2.2u
1SS357
(T3SONY1)
1SS357
(T3SONY1)
2SC4738F-Y
UPO44O1OO8SO
100k
100k
4.7k
220k
68k
12k
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
8.2k
L
16
4-49
4-50
DC/DC CONVERTER
VC-254 (18/18)
LS-057 (S/T REEL SENSOR), FP-228 (DEW SENSOR), FP-229 (MODE SWITCH), FP-300 (TAPE TOP), FP-302 (TAPE END), FP-301 (TAPE LED) FLEXIBLE BOARDS
FP-302
FLEXIBLE
FP-300 FLEXIBLE (COMPONENT SIDE)
LS-057 BOARD
FP-300
FLEXIBLE
Q002
TAPE END
Q001
TAPE TOP
FP-301
FLEXIBLE
D001
TAPE LED
Q001
TAPE TOP
SENSOR
1-680-436-
H002
3
S REEL
SENSOR
4
1
2
15
ME/MP
REC PROOF
H001
3
2
T REEL
SENSOR
4
1
11
LS-057 BOARD
(CONDUCTOR SIDE)
15
S001
REC PROOF
15
Hi8 MP
S002
C.C. LOCK
S901
MODE SWITCH
o'
FP-299
FLEXIBLE
DEW SENSOR
1-680-437-
MR SENSOR
FP-228
FLEXIBLE
T REEL (+)
10
T REEL (-)
TO
MECHA
CONTROL
BLOCK
11 HALL COM
12 ME/MP
13 REC PROOF
14 Hi8 MP
DEW
FG1 (Vo2)
VCC
FG2 (Vo1)
7
8
GND (C0M)
9 COIL-U
10 COIL-U
11 COIL-W
12 COIL-W
13 COIL-V
3
4
2
HE
FP-302 FLEXIBLE
(CONDUCTOR SIDE)
o'
Q002
TAPE END
SENSOR
11

22
4-52
2
HE
11
1-680-438-
2
HE
1-680-434-
SENSOR (Vcc)
LS-057, FP-228, FP-229, FP-300, FP-302, FP-301
14 COIL-V
1-677-049- 11
S/T REEL SENSOR, DEW SENSOR, MODE SWITCH, TAPE TOP, TAPE END, TAPE LED
S REEL (+)
MR
2
SENSOR
3
S REEL (-)
M902
CAPSTAN
MOTOR
FP-301 FLEXIBLE
(CONDUCTOR SIDE)
DEW SENSOR
S901
MODE
SWITCH
1-680-473-
GND
11
11
TAPE LED (A)
C
B
A
COM
TAPE LED (K)
S002
C.C. LOCK
D001
TAPE LED
H002
S REEL
SENSOR
TAPE END (C)
15 C LOCK SW
S001
H001
T REEL
SENSOR
FP-228
FLEXIBLE
TAPE TOP (C)
FP-299
FLEXIBLE
M902
CAPSTAN
MOTOR
15
VH+
16
HU 1
17
HU 2
18
HV 1
19
HV 2
20
21
HW 1
HW 2
22
VH-
TO
MECHA
CONTROL
BLOCK
FP-270 (S VIDEO, AUDIO/VIDEO), FP-272 (LANC, DV IN/OUT) FLEXIBLE BOARDS

Ref. No. FP-270, FP-272 Flexible Boards; 30,000 Series
Refer to page 4-27 for schematic diagram.

Chip parts
PC-082 (TRV330/TRV530)
DS STILL PROCESS
FU-150 (TRV230/TRV330)
FU-154 (TRV530)
(POWER SUPPLY)
Diode
FP-273
(MIC, HEADPHONES)

4-53
FP-272
(LANC, DV IN/OUT)
FP-270
FP-271 (TRV330/TRV530)
(USB)
4-54
S VIDEO, AUDIO/VIDEO
FP-270
/ LANC, DV IN/OUT
FP-272
PC-082 (DIGITAL STILL CONTROL, DS STILL PROCESS) PRINTED WIRING BOARD

Ref. No. PC-082 Board; 20,000 Series

PC-082 board consists of multiple layers. However, only
Chip parts
Transistor
C

PC-082 (TRV330/TRV530)
DS STILL PROCESS
FU-150 (TRV230/TRV330)
FU-154 (TRV530)
(POWER SUPPLY)
FP-273
(MIC, HEADPHONES)
FP-272
(LANC, DV IN/OUT)
FP-270
FP-271 (TRV330/TRV530)
(USB)
DIGITAL STILL CONTROL, DS STILL PROCESS

PC-082
4-56
4-57
DIGITAL STILL CONTROL, DS STILL PROCESS

PC-082

Refer to page 4-55 for PC-082 printed wiring board.
2
PC-082 BOARD(1/3)
12
11
10
14
13
15
16
17
18
19
20
21
22
(DCR-TRV330/TRV530)
R1151
0
2
XTAL
OSC
1.4
DS_MAD
XRAS
XCAS
SDRAM_CKE
DS_MAD
RXD
TXD
2.8
TXD
SCK
SCK
HDS
C1162
XX
B
C1151
0.1u
B
IC1151
TC7SHU04FU-TE85R
L1151
100uH
DS_MAD
RXD
C1152
XX
C1197
10u
4V
TA A
C1190
0.1u
B
BUFFER
USB_D+PULLUP
1.4
IC1152
XBACK
R1152
1M
IC1151
XBREQ
X1151
48MHz
C1153
XX
VFI_OE
USB_D-IN
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
USB_D+IN
USB_D-OUT
USB_D+OUT
DIGITAL STILL CONTROL1
HDS
XSYS_RST
SYSCLK
XSYS_RST
XHI_SCK
XHI_SCK
HI_SO
HI_SO
TO(3/3)
TO(2/3,3/3)
HI_SI
HI_SI
R1207
470k
VDR112
R1188
0
47k
RB1156
100k
R1177
C1967
B
XX
100k
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.9
1.4
XX
R1175
2.8
2.8
1.4
2.8
1.9
2.8
2.8
2.8
2.8
2.8
3.1
1.2
2.8
1.9
R1176
C1199
XX B
C1160
470p
C1158
470p
1.9
2.8
1.9
NC
CKE
A20
MS_SCLK
A21
A19
A18
MS_BS
MS_DIO
A17
NC(XMS_DIR/PCT0)
A16
NC(S_RAQ)
A15
NC(S_RAK)
VCCQ
A14
NC(J_XDREQ)
S_REQ
VSSQ
A13
XRESET
VCCQ
A12
MD3
A11
MD4
A10
VSS
A9
AVSS
A8
NC(P_STAT0)
A7
NC(P_STAT1)
A6
NC(P_STAT2)
A5
VCCQ
NC(P_STAT3)
NC(P_CACK)
A4
NC(P_DACK)
VSSQ
AVCC
A3
NC(P_IEND)
A2
NC(P_BW/XCOL)
A1
AVSS
NC
RXD
IC1159
BUFFER
A0
NC
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108
XCAS
XRAS
NC(XRAS2L/PTJ1)
VCCQ
VSSQ
NC(XCASLH/CASU/PTJ3)
J_XDACK
USB_D+PULLUP
NC(XCASHL/PTJ4)
NC(XCAS2H/PTE3)
NC(XCAS2L/PTE6)
NC(XDACK1/PTD7)
NC(XRAS3U/PTE2)
NC(XRAS2U/PTE1)
XBACK
KAT_TDO
XBREQ
XWAIT
VFI_OE
XRESETM
XASEMD0
NC(232C_ON)
UCLK
AUDATA3
ASEBRKAK
AUDATA2
VSS
VCC
AUDATA1
AUDATA0
KAT_TDI
KAT_TMS
KAT_XTRST
KAT_TCK
USB_D-IN
USB_D+IN
MD0
USB_D-OUT
USB_D+OUT
VCC(PLL1)
CAP1
VSS(PLL1)
VSS(PLL2)
CAP2
VSS
AUDCK
VSS
VCC
XTAL
USB_SUSPND
TO(2/3)
USB_D+IN
USB_D-IN
USB_D-IN
USB_SUSPND
USB_SUSPND
0
A19
2.8
SHIORI_XCS
A18
2.8
SDRAM_XCS
R1168
100k
A17
2.8
R1167
2.8
A18
A16
A15
100k
2.8
A15
A14
A14
A12
A12
SYSCK
SYSCLK
XWE
A1
UA1
A2
R1189
100k
UA2
A3
XRD
XWRH
XWRH
XWR
2.8
XRD
XWRH
A5
UA3
UA4
D0
TO(3/3)
XBACK
D1
S_IRQREQ
D2
UAD0
UAD1
S_IRQREQ
UAD2
D3
SHIORI_XCS
C1166
0.1u
B
A4
XBREQ
XBACK
2.8
XURD
UA5
XBREQ
R1170
3300
SHIORI_XCS
IRQSOU
UAD3
D4
IRQSOU
S_XINT
UAD4
D5
S_XINT
UAD5
D6
C1167
0.1u
B
1.9
A17
A16
FLASH_XCS
C1182
0.1u B
R1186
4700
2.8
A19
UAD6
D7
UAD7
D8
RB1154
100k
D8
RB1155
100k
D9
D9
D10
D10
D11
A19
2.8
A18
D13
2.8
A17
D14
2.8
A16
D15
2.8
A15
A6
A13
VFI_OE
A12
XDS_FLASH_RST
2.8
A9
2.8
A8
2.8
A7
2.8
A6
2.8
A5
MS_XINSERT
A8
A9
A10
VFI_OE
TO(3/3)
A10
A11
XDS_FLASH_RST
A11
A13
MS_IN
A13
SDRAM_CKE
SDRAM_CKE
XWE
XWE
XCAS
2.8
2.8
A7
A9
VFI_VD
2.8
A10
A3
2.8
A2
XCAS
XRAS
A4
C1180
0.1u
B
2.8
XRAS
SDRAM_XCS
SDRAM_XCS
XWRH
XWRH
SYSCLK
SYSCLK
XWR
2.8
TO(3/3)
A6
A8
VFI_VD
2.8
A11
D14
A7
2.8
TO(2/3)
D15
A14
C1181
0.1u B
2.8
D12
D13
2.8
2.8
D11
D12
2.8
XWR
A1
XDS_FLASH_RST
XDS_FLASH_RST
ARD
ARD
FLASH_XCS
FLASH_XCS
S_GND
11
FP-274
TO(3/3)
FB1153
Q1153
RN1104F(TPL3)
INV
16
DO
R1182
4700
R1180
1k
R1169
100k
3.1
R1185
1k
0
D1151
MA111-(K8).S0
MS_BS
MS_DIO
3.1
MS_XINSERT
MS VCC
SWITCH
MS_SCLK
C1196 C1195
0.1u 0.1u
B
B
Q1154
RN1107F(TPL3)
FB1155 R1163
47
LM751
1608
D1152
UDZS-TE17-8.2B
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
MS_VCC_ON
AUDIO_MUTE
S_IRQREQ
6
DI
C1168
10u
4V
TA A
PC_1.9V
FB1154
RST
GND
1
2
4
N.C
XSCK
R1206
XX
3.1
MS_VCC_ON
TO(2/3)
Q1155
2SA1832F-Y/GR(TPL3)
B+
SWITCH
FB1158
0uH
C1188
XX
4V
TA A
R1204
XX
R1208
100k
VCC
XCS
VFI_VD
MS_XINSERT
XEEP_SCK
EEP_DI
ACCESS_LED
C1177
0.1u
B
C1157
XX
B
19
3.1V
0uH
2.8
2.8
2.8
2.8
2.8
2.8
C1179
0.1u B
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
C1178
0.1u
B
2.8
1.9
2.8
C1169
10u
4V
TA A
2.8
EEP_DO
C1163
0.1u
B
C1161
0.1u
B
XDS_WAKE_UP
R1153
0
2.8
2.8
0
R1160 R1159
100k
100k
R1155
47k
PC_2.8V
10
TO(3/3)
12
TO(2/3,3/3)
REG_GND
C1968
XX
B
IC1162
XX
DIGITAL STILL CONTROL 1

PC-082 (1/3)
4-59
FLEXIBLE
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
CN1153
R1157
0
AUDIO
SIGNAL
USB_XVDATA
NC
IC1159
TC7W08FU(TE12R)
IC1155
HD6417197FL77
VCCQ
D0
VSS
D1
GND
2Y
1B
DIGITAL
STILL
CONTROL
USB_VBUS
A22
D2
VCC
D3
C1184
XX
B
1A
R1203
470k
VSSQ
IC1155
D4
USB_TXENL
VCCQ
2A
C1185
0.1u
B
A23
USB_XVDATA
D5
2B
1Y
VCC
VSSQ
LMODE_VIDEO
VSSQ
HDS
0
8
A24
S_XINT
D6
2.8
Q1158
XX
VCCQ
D7
C1194
0.01u
B
LMODE_AUDIO
D8
R1196
XX
2.8
A25
D9
R1211
1k
VCC
D10
R1195
XX
XBS
D11
R1158
0
UART_RXD
D12
DS_XRESETM
XRD
VSS
D13
2.8
XWRL
EEP_DO
D14
0.2
MS_BS
MS_DIO
XWRH
VCCQ
Q1157
XX
C1159
XX
R1197
XX
SI_FROM_HI
D15
XSYS_RST
R1162
XX
NC
VSSQ
MS_SCLK
NC
XCS_HI
MS_VCC_ON
USB_SUSPND
UART_RTS
NC
2.8
USB_DET
XWE
NC
R1205
100
UART_TX
VCC
2.8
USB_TXENL
SCK
AUDSYNC
NC
C1154
0.1u
B
EEP_SCK
VSS
C1156
0.1u
USB_XVDATA B
VSSQ
NC
0
0
S_XINT
C1970
XX
CH
R1202
XX
1.9
R1165
100k
EEP_DI
EEP_XRST
R1166
100k
IRQSOU
FLASH_XCS
MECH_MUTE_REQ
HI_SCK
LM_IRQREQ
EEP_DO
DS_MAD
VCCQ
NC
2.8
NC
VO_XPI
SO_TO_HI
VCCQ
2.1
Y/CHROMA
PB
USB_TXENL
NC(SDRAM2_XCS)
XCS_EEP
2.7
USB_D+PULLUP
USB_TXENL
REC
USB_D-OUT
USB_D+IN
VCCQ
VSSQ
HI_SO
R1172
100
R1173
100
VIDEO SIGNAL
CHROMA
USB_D+OUT
USB_D-OUT
SDRAM_XCS
UART_CTS
2.8
2.8
2.8
USB_D+OUT
USB_XVDATA
CLK
NC
2.8
2.8
XCS_DS
LPLATZ_XCS
NC
0
2.8
XEEP_SCK
R1201
XX
2.8
CALLION_XCS
NC
2.5
SIGNAL PATH
ACCESS_LED
USB_DET
VSSQ
NC
2.4
C1155
XX
B
EEP_DI
AUDIO_MUTE
ACCESS_LED
USB_DET
NC(XIRQOUT)
LED_ON
2.8
UART_CTS
R1200
XX
AUDIO_MUTE
JPEG_XCS
NC(IRQ3/XIRL3/PTH3)
C1187
XX
B
DS_XRESETM
C1186
XX
B
AUCLK
XCSHI_IRQ
GND
2Y
1B
1A
C1183
0.1u
B
NC(STATUS1)
VSS(RTC)
0.8
NMI
2.8
MS_XINSERT
0
VD
R1171
100
HI_SI
XDS_WAKE_UP
DS_XRESETM
R1154
4700
NC(STATUS0)
NC
1.9
VCC(RTC)
2.8
R1192
47k
R1191
0
C1971
XX
CH
XDS_WAKE_UP
RB1152
4700
RB1151
4700
NC
VSS
2.0
VCC(RTC)
R1199
XX
5
2A
1Y
NC
2.8
MD1
2.8
TXD
2.8
7
VCC
2B
2.8
XCS_DS
USB_D+PULLUP
VCC(PLL2)
R1198
100
NC
BUFFER
XCS_DS
162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109
216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163
2.5
IC1152
TC7S08F(TE85R)
IC1160
IC1160
R1156
1M
2.8
TC7W08FU(TE12R)
C1198
XX
B
EXTAL
R1187
0
X1152
25.8048MHz
2.8
2.5
R1161
4700
C1175
8p
CH
VDR111
C1176
8p
CH
XHI_SCK
4-60
R1164
XX
12P
S_GND
S_GND
S_GND
MS_VSS
N.C
MS_BS
GND
MS_VCC
MS_BS
MS_DIO
MS_VCC
N.C
MS_DIO
MS_INSERT
S_GND
CN001
MS_INSERT
N.C
10
MS_SCLK
MS_SCLK
11
MS_VCC
MS_VCC
12
GND
10
MS_VSS
10P
MEMORY
STICK
CONNECTOR

Refer to page 4-55 for PC-082 printed wiring board.
PC-082 BOARD(2/3)
10
12
11
13
14
15
16
(DCR-TRV330/TRV530)
DIGITAL STILL CONTROL2

NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
A19
2 TO(1/3)
D10
D11
D12
D13
D14
D15
A6
A7
A8
A9
A10
A11
D4
DQ3
DQ12
DQ4
DQ11
Vccq
Vssq
DQ5
D1
D2
D5
D3
D6
D4
D5
D7
D6
D7
D8
C1973
XX
B
D9
D12
XWE
XCAS
D10
D11
XWR
XRAS
SDRAM_XCS
R1210
XX
D13
A13
D14
A11
D15
A1
A6
A2
A7
A3
A8
A4
A9
A10
A11
C1974
XX
B
DQ10
DQ6
DQ9
Vssq
Vccq
DQ7
DQ8
Vcc
Vss
DQML
NC
XWE
DQMU
XCAS
CLK
XRAS
CKE
XCS
NC
A13
A11
A12
A9
A10
A8
A0
A7
A1
A6
A2
A5
A3
A4
Vcc
Vss
USB_D-OUT
USB_D+OUT
USB_TXENL
USB_D+PULLUP
USB_XVDATA
USB_D-IN
D13
D12
D11
C1200
XX
7 TO(1/3,2/3)
USB_DET
D10
D9
3.1
IC1157
D8
FP-271
Q1156
RN2104F(TPL3)
SWITCH
2.8
USB I/F
FLEXIBLE
LND201
XX MARK:NO MOUNT
R1193
150K
SHASSIS GND
0.5
XWRH
R1184
XX
SYSCLK
IC1157
PDIUSBP11APW,118
R1183
XX
2.7
MODE
OE#
VMO/FSEO
RCV
VPO
VP
VCC
2.8
SDRAM_CKE
R1209
XX
3.1
A10
3.1
A9
2.8
A8
USB_D+
VM
USB_D-
SUSPND
GND
3.1
D0
USB_D+IN
Vccq
USB_SUSPND
Vssq
SPEED
(NC)
D207
XX
R1181
1500
R1194
100K
D206
XX
D205
XX
C201
2200p B
D9
D3
10 11 12 13 14
D8
A5
D14
UAD7
DQ13
UAD6
DQ14
DQ2
UAD5
DQ1
A4
D15
UAD3
UAD4
Vssq
UAD2
Vccq
Vss
UAD1
D2
DQ15
UA5
UAD0
A3
DQ0
A2
D1
Vcc
UA4
D0
C1972
XX
B
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
UA3
A1
UA2
A12
XX
UA1
A14
A12
3 TO(1/3)
IC1161
A15
A14
A16
A15
A17
A16
A18
A17
A18
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
A19
D201
MA111-(K8).S0
LF201
0
CN1152
2.8
0.4
R1178
24
6P
USB_VCC
USB_D+
USB_D-
REG_GND
REG_GND
CN201
0.4
A7
R1179
24
C1193
C1189
XX
0.1u
4V
B
A TA
FB1156
0uH
LF202
REG_GND
A6
VCC
D-
D+
ID
GND
5P
DIGITAL I/O
(USB)
A5
C1969
XX
B
A13
A13
IC1153
IC1154
16Mbit SDRAM
2.8
VccQ
DQ4
DQ11
ARD
FLASH_XCS
DQ5
DQ10
VssQ
VssQ
D6
2.8
D7
2.8
XWR
XWE
2.8
XCAS
2.8
XRAS
2.8
A13
2.8
A11
2.8
A1
2.8
A2
2.8
A3
2.8
A4
2.8
DQ6
DQ9
DQ7
DQ8
VccQ
VccQ
DQML
XWE
DU
DQMU
XCAS
CLK
XRAS
CKE
XCS
DU
A11(BA)
A9
A10/AP
A8
A0
A7
A1
A6
A2
A5
A3
A4
Vcc
Vss
2.8
2.8
2.8
D11
D9
2.8
D8
A10
2.8
A9
2.8
XWRH
XDS_FLASH_RST
R1190
100k
XWRH
2.8
SYSCLK
SDRAM_CKE
A10
A19
2.8
A18
2.8
A8
2.8
A7
2.8
2.8
A9
A6
2.8
2.8
A8
A5
2.8
2.8
A7
A4
2.8
2.8
A6
A3
2.8
A5
A2
2.8
2.8
DQ15/A1
2.8
2.8
2.8
A12
2.8
A11
A10
A9
A8
NC
DQ5
NC
DQ12
DQ7
DQ14
DQ6
DQ13
D10
2.8
A11
D12
Vss
D13
2.8
A13
BYTE
C1171
0.1u
B
FB1151
0uH
XWE
2.8
XRESET
NC
NC
RY/XBY
A18
DQ4
Vcc
DQ11
DQ3
DQ10
DQ2
A17
DQ9
A7
DQ1
A6
DQ8
A5
DQ0
A4
OE
A3
A2
Vss
2.8
CE
A1
A0
A17
CHROMA
2.8
Y/CHROMA
AUDIO
SIGNAL
REC
2.8
D15
2.8
D7
2.8
D14
2.8
D6
2.8
D13
2.8
D5
2.8
D12
2.8
D4
PB
IC1158
RN5RZ31BA-TL
4.7
D5
VccQ
2.8
A12
A14
VIDEO SIGNAL
2.8
IC1158
2.8
2.8
D11
2.8
D3
2.8
D10
2.8
D2
2.8
D9
2.8
D1
2.8
D8
2.8
D0
2.8
XRD
3.1V REG
4.7
2.8
SIGNAL PATH
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
D4
SDRAM_XCS 2.8
DQ12
DQ3
XWR
XDS_FLASH_RST
FLASH_XCS
DQ13
DQ2
A13
A16
2.8
D14
A14
A15
2.8
2.8
D2
D3
2.8
A15
XWRH
SYSCLK
2.8
A16
D15
ARD
VssQ
2.8
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
DQ14
VssQ
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
XWR
XDS_FLASH_RST
XWRH
DQ1
2.8
SDRAM_XCS
SYSCLK
DQ15
D1
DQ0
XRAS
XRAS
Vss
XCAS
SDRAM_XCS
Vcc
2.8
D0
XCAS
MB81F161622C-80FN
XWE
XWE
IC1153
C1170
0.1u
B
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
SDRAM_CKE
SDRAM_CKE
4Mbit FLASH MEMORY

IC1154
MBM29LV400BC-90PFTN-S112-ER
3.1
C1192
0.1u
B
C1191
0.1u
B
REG_GND
PC_2.8V
IC1156
XX
5
4
12 TO(1/3,3/3)
FLASH_XCS
2.8
A1
1
C1172
0.1u
B
FB1152
0uH
3
A_4.75V
C1165
XX
B
C1173
10u
4V
TA A
C1174
10u
4V
TA A
C1164
XX
B
8 TO(3/3)
R1174 0
D_2.8V
3.1V
9 TO(1/3)
L
16
4-61
4-62
DIGITAL STILL CONTROL 2

PC-082 (2/3)

2
3
1
11
10
12
14
13
15
16
17
VFO_HD
A13
A11
A10
A9
A6
A8
A7
UA4
UA5
UA3
UA1
UA2
XWE
VFI_VD
VFO_HD
SDRAM_XCS
VFI_OE
VFI_VD
XCAS
VFI_OE
VFI_Y1
VFI_Y1
SDRAM_CKE
VFI_Y0
VFI_HD
D15
D14
D13
VFI_Y0
VFI_HD
D11
REG_GND
D12
XRAS
1 TO(1/3)
B_TO_B
REG_GND
D9
CN1901 100P
D10
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
D8
UAD6
DS STILL PROCESS
(DCR-TRV330/TRV530)
UAD7
PC-082 BOARD(3/3)
5 TO(1/3)
12
VFI_Y5
13
VFO_OE
14
VFI_Y6
15
VFO_Y0
16
VFIO_C5
VFI_OE
C1912
0.1u
B
VFO_Y7
11
MS_IN
VFO_Y6
VFI_Y4
MS_IN
VFIO_C4
9
10
VFO_VD
VFO_Y5
VFI_Y3
VFI_Y3
VFO_VD
XDS_FLASH_RST
VFO_Y4
XDS_FLASH_RST
VFI_VD
VFO_Y3
VFO_Y2
VFO_Y0
VFI_Y2
VFI_VD
VFO_Y1
VFI_Y2
VFI_Y4
C1911
0.1u
B
VFI_OE
VFI_Y5
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
UAD5
2.8
VFO_Y4
2.8
UAD3
IFI_Y3
VFO_Y5
1 TO(1/3)
26
UAD0
IFI_Y5
0
XURD
IFI_Y7
XBREQ
2.8
33
4 TO(1/3)
VFI_C1
2.8
34
VFI_C2
S_XINT
0
0
IFI_VD
IRQSOU
VFI_C3
SYSCLK
37
SSS_FROM_VC
IFI_HD
IFI_C0
SSS_FROM_L
KASYAON
XWEN_FROM_L
2.8
IFI_C1
DS_XRESETM
IFI_C2
AFCK
XCS_HONEY
C1915
XX
B
2.8
IFI_C3
XVSP_SCK
SPCK
IFI_C4
2.7
VSP_SO
0.7
VSP_SI
2.5
MS_IN
2.8
SFD_LRCK
1.4
SFD_BCK
1.4
DATA_FROM_SFD
0.7
TDI
TCK
VFIO_C4
TMS
57
VFIO_C5
XVSP_SCK
VFIO_C6
TDI
60
TD_2-3
TCK
VFIO_C7
TD_2-3
XCS_HONEY
PC_1.9V
72
SFD_BCK
73
SFD_LRCK
74
VSP_SI
75
REG_GND
76
REG_GND
78
D_2.8V
79
A_4.75V
82
VSP_SI
83
SSS_FROM_L
84
IC1902
XX
1
D_2.8V
85
86
VFO_OE
R0/P1.4
1.5
C1910
0.1u
B
C1909
0.1u
B
1.5
N.C.
LDRA11
YO0
YO1
YO2
YO3
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
0
C1908
0.1u
B
C1907
0.1u
B
A_4.75V
C1916 XX CH
C1906
470p
R1906
47k
Q1902
RN2104F(TPL3)
RESET SW
R1908
XX
ADAI2
ADAI2
SSS_FROM_VC
SSS_FROM_L
DATA_FROM_SFD
VFO_VD
2.8
8 TO(2/3)
XWEN_FROM_L
XWEN_FROM_L
SFD_BCK
XWEN_FROM_VC
81
SSS_FROM_VC
VFO_HD
R2.8/P2.6
SFD_LRCK
80
XWEN_FROM_VC
1.0
R1902
XX
1.1
Q1901
XX
1.1
10 TO(1/3)
77
D_2.8V
C1904
10u
4V
TA A
NM
PC_1.9V
YO4
71
1.1
PC_1.9V
KASYAON
1.7
70
YO5
D_1.5V
HI_SO
XSYS_RST
YO6
69
1.2
68
N.C.
C1905
10u
4V
TA A
R1904
XX
R1903
0
1.4
HI_SO
XSYS_RST
XCS_DS
YO7
67
LDRA10
N.C.
DVDD1
66
R1905 0
FB1902
VFIO_C7
R0/P0.8
HI_SI
CO0
HI_SI
XCS_DS
TMS
XHI_SCK
XDS_WAKE_UP
VSS3
LDRA9
N.C.
64
65
LDRA8
63
XHI_SCK
LDRA7
TCK
2.8
TDO
2.7
TMS
LDRA6
VFIO_C6
R0/P0.9
R1915
XX
XCS_HONEY
XDS_WAKE_UP
N.C.
2.8
TDI
0.9
62
LDRA5
1.5
61
LDRA4
AOUT
2.8
AVSS
CO1
TD_2-3
VFIO_C7
LDRA3
AVDD
1.0
VFIO_C6
LDRA2
N.C.
CO2
59
LDRA1
VPDX
0.9
58
ASO
CO3
VFIO_C5
XVSP_SCK
LDRA0
0.9
IOVDD2
ASI
0.8
TMS
2.8
C1902
0.1u
B
XRAS2
SCLK
HDO
56
IFI_C7
LRCK
VDO
VFIO_C4
OEO
55
ADAI2
2.6
54
TCK
VSP_SO
XCAS2
2.8
IFI_C7
IFI_C6
VSS8
1.4
53
XWE2
VSS2
52
MCSO
CAMYI0
51
XCSO2
CAMYI1
TDI
IFI_C6
VSP_SO
CKE2
MCSI
R1.1/P0
50
CLK2
MCXSCK
R1.1/P0
49
IFI_C5
MCXCS
CAMYI2
MS_IN
IFI_C5
LDRD15
CAMYI3
48
LDRD14
XRST
CAMYI4
47
LDRD13
SYSCK
R1.1/P0
46
IFI_C4
R1912
0
SDCK
R1.2/P0
IFI_C3
SPCK0
2.8
CAMYI5
45
LDRD12
CAMYI6
44
AFCK
LDRA11
XSWEO
R1.7/P0
43
IFI_C2
LDRD10
IC1901
MB87J4421PFF-G-BND
SSSO
R1.2/P0
DS_XRESETM
R1914
0
XSWE
CAMYI7
R1.4/P0
42
R0.9/P0.1
IFI_C1
LDRD9
IOVDD1
41
VSS4
LDRD8
SSS
AFCCK
40
2.8
LDRD7
DS STILL PROCESS
IOVDD4
2.8
IFI_C0
KASYAON
XWEN_FROM_VC
IRQSOU
CAMHDI
39
LDRD6
IC1901
XINT
2.8
38
IFI_HD
LDRD5
IRQREQ
CAMVDI
VFI_C3
2.8
LDRD4
XBACK
R2.6/P2.8
36
S_IRQREQ
LDRD3
XBREQ
CAMOEI
35
IFI_OE
LDRD2
XURD
2.8
IFI_OE
VFI_C2
IFI_VD
2.8
XBACK
XUWR
R1.4/P0.1
VFI_C1
2.8
VSS1
IFI_Y7
XUWRH
VFI_C0
LDRD1
MCK
(SEE PAGE 4-48)
32
LDRD0
XCSI
CAMCI0
31
DRD0
1.5
TO
VC-254 BOARD(17/18)
CN1104
IFI_Y6
VFI_C0
2.8
SHIORI_XCS
VFO_Y7
IFI_Y6
DVDD2
CAMCI1
30
DRD1
CAMCI2
29
2.8
NROE
R1.0/P0
IFI_Y5
VFO_Y7
2.8
UAD1
VFO_Y6
NRVD
DRD2
R1.0/P0
28
VSS7
CAMCI3
27
NRHD
R1.0/P0
IFI_Y4
VFO_Y6
2.8
UAD2
IFI_Y4
DRD3
CAMCI4
VFO_Y5
NRCI3
CAMCI5
NRCI2
DRD4
R0.9/P0
25
N.C.
DRD5
CAMCI6
24
IFI_Y3
N.C.
VFO_Y4
UAD4
45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
VFO_Y3
IFI_Y2
23
CAMCI7
22
21
IFI_Y2
TEST
IFI_Y1
176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133
IFI_Y1
VFO_Y3
NRYI5
R0/P1.3
NRYI6
R0/P1.4
NRYI7
R0/P0.7
NRCI0
R0/P1.0
NRCI1
R0/P1.0
N.C.
NRYI0
R0/P0.9
NRYI1
R0/P1.2
NRYI2
R0/P1.2
NRYI3
R0.1/P1.2
NRYI4
R0/P1.8
VSS5
DRA12
DRA11
DRA10
DRA9
DRA8
IOVDD3
DRA7
DRA6
DRA5
DRA4
DRA3
DRA2
DRA1
VSS6
DRA0
XRAS
XCAS
XWE
XCSO
CKE
DRD15
DRD14
DRD13
C1914
0.1u
B
VFO_Y2
DRD12
IFI_Y0
DRD11
20
DRD9
19
N.C.
DRD8
IFI_Y0
VFO_Y2
VFO_Y1
DRD10
18
DRD7
17
DVDD3
VFI_Y7
DRD6
132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89
VFI_Y7
VFO_Y1
1.5
2.8
D_1.5V
VFO_Y0
2.8
VFO_OE
VFI_Y6
DATA_FROM_SFD
87
USB_DET
88
AUDIO_MUTE
RXD
89
RXD
TXD
90
TXD
HDS
91
SCK
92
XDS_FLASH_RST
93
DS STILL PROCESS
PC-082 (3/3)
4-63
XCS_DS
4-64
VFI_Y0
VFI_Y1
VFI_Y2
VFI_Y3
VFI_Y4
VFI_Y5
VFI_Y6
VFI_Y7
VFI_C0
VFI_C1
VFI_C2
VFI_C3
VFI_HD
VFI_VD
VFI_OE
IFI_Y0
IFI_Y1
IFI_Y2
REC
IFI_Y3
D1902
XX
IFI_Y4
XSYS_RST
IFI_Y5
HI_SO
IFI_Y6
XSYS_RST
CHROMA
IFI_Y7
HI_SO
VIDEO SIGNAL
CHASSIS_GND
AFCK
100
SIGNAL PATH
11 TO(1/3)
IFI_HD
REG_GND
HI_SI
S_GND
LND192
IFI_VD
16
D1901
XX
C1903
0.1u
B
IFI_OE
XCS_DS
6 TO(1/3)
SPCK
99
XDS_WAKE_UP
IFI_C0
REG_GND
XHI_SCK
IFI_C1
HI_SI
IFI_C2
XDS_WAKE_UP
IFI_C3
98
LND191
CHASSIS_GND
IFI_C4
97
REG_GND
R1911
XX
ACCESS_LED
DS_XRESETM
IFI_C5
REG_GND
12 TO(1/3,2/3)
1uH
REG_GND
DS_MAD
DS_XRESETM
XHI_SCK
FB1903
SCK
IFI_C6
95
PC_2.8V
HDS
XDS_FLASH_RST
94
96
Q1903
RN1104F(TPL3)
RESET SW
IFI_C7
MS_LED
DS_MAD
REG_GND
7 TO(1/3,2/3)
XSYS_RST
USB_DET
AUDIO_MUTE
R1907
0
PB
Y/CHROMA
AUDIO
SIGNAL
FP-271 (USB), FP-282 (FOCUS), FP-275 (SWITCH) FLEXIBLE BOARDS

Ref. No. FP-271, FP-282, FP-275 Flexible Boards; 30,000 Series

FP-271 flexible board consists of multiple layers.
FP-282, FP-275 flexible boards consists of multiple
layers. However, only the sides (layers) A is shown.

PC-082 (TRV330/TRV530)
DS STILL PROCESS
FU-150 (TRV230/TRV330)
FU-154 (TRV530)
(POWER SUPPLY)
FP-273
(MIC, HEADPHONES)
FP-272
(LANC, DV IN/OUT)
FP-270
FP-271 (TRV330/TRV530)
(USB)
SI-028 (TRV230/TRV330)
SI-029 (TRV530)
LASER LINK
FP-283
FP-275
(PANEL REVERSE)
(SWITCH)
VC-254
DC/DC CONVERTER
FP-282
(FOCUS)
4-65
4-66
USB
FP-271
FOCUS
FP-282
/ SWITCH
FP-275
CF-079 (USER FUNCTION, EVF DRIVE) PRINTED WIRING BOARD (DCR-TRV230/TRV330)

Ref. No. CF-079 Board; 1,000 Series

CF-079 board consists of multiple layers. However, only
Chip parts
Transistor
Diode

LB-068 (TRV230/TRV330)
LB-070 (TRV530)
(EVF BACK LIGHT)
CF-079 (TRV230/TRV330)
CF-080 (TRV530)
CD-292 (TRV230/TRV330)
CD-315 (TRV530)
(CCD IMAGER)
PD-138 (TRV230/TRV330)
PD-139 (TRV530)
USER FUNCTION, EVF DRIVE

CF-079
4-67
4-68
4-69
4-70

CF-079
CF-080 (USER FUNCTION, EVF DRIVE) PRINTED WIRING BOARD (DCR-TRV530)

Ref. No. CF-080 Board; 1,000 Series

CF-080 board consists of multiple layers. However, only
Chip parts
Transistor
Diode

LB-068 (TRV230/TRV330)
LB-070 (TRV530)
(EVF BACK LIGHT)
CF-079 (TRV230/TRV330)
CF-080 (TRV530)
CD-292 (TRV230/TRV330)
CD-315 (TRV530)
(CCD IMAGER)
PD-138 (TRV230/TRV330)
PD-139 (TRV530)

CF-080
4-71
4-72
4-73
4-74

CF-080

Refer to page 4-67 (CF-079), 4-71 (CF-080) for printed wiring board.
Refer to page 4-65 for printed wiring boards of FP-282, FP-275 flexible.
10
11
(DCR-TRV230/TRV330)
CF-079 BOARD(1/2)
CF-080 BOARD(1/2)
S117
S116
TO
VC-254 BOARD(17/18)
CN1117
EDITSEARCH+
EDITSEARCH-
D402
01BZA8.2(TE85L)
REG_GND
REG_GND
REG_GND
EVF_2.8V
EVF_13.3V
REG_GND
CN104
R112
0
2012
D109
UDZS-TE17-8.2B
REG_GND
EVF_2.8V
D_2.8V
EVF_13.3V
KEY_AD1
EVF_B
EVF_B
XIR_LED_ON
BW_Y
BW_Y
EVF_R
EVF_R
PANEL_XHD
EVF_XHD
PANEL_XVD
10
EVF_XVD
XCS_EVF
11
XCS_EVF
XHI_SCK
12
XHI_SCK
HI_SO
13
HI_SO
XSYS_RST
14
XSYS_RST
VCO
15
VCO
VG
16
EVF_VG
VR
17
EVF_VR
R129 1200
1 TO(2/2)
S402
8P
01ZA8.2(TPL3)
D107
SUPER LASER LINK
KEY_AD0
S_NIGHT_SW
REG_GND
SEIDEN_GND
R410
1500
S401
S403
2 TO(2/2)
EVF_VB
19
XTALLY_LED
EVF_4.75V
20
EVF_4.75V
EVF_DD_ON
21
D_2.8V
22
KEY_AD1
23
XIR_LED_ON
24
R405
1500
R406
8200
S407
S409
REW
PLAY
R408
3900
R407
2200
KEY_AD0
25
KEY_AD2
26
KEY_AD3
27
KEY_AD4
28
MS_LED
29
MENU
DIAL_A
1.6
R102
D103
120
CL-270HR-C-TS
(MEMORY STICK)
33
SP_+
SP_+
34
SP_-
35
REG_GND
36
BATT_LI_3V
37
XCS_LCD_DRIVER
38
LCD_COM/XDATA
39
OSD_SO
40
SP_-
41
EVER_3.0V
42
LCD_LED_ON
43
VTR_UNREG
44
REG_GND
45
R123
8200
VOLUME+
VOLUME-
BACKLIGHT
DIAL_B
DIAL_A
BT101
D111
XX
D110
XX
R128
47k
(TRV330/TRV530)
R131
33
XCS_LCD_DRIVER
D112
XX
D104
MA111-(K8).S0
(TRV230)
S104
R110
1200
S106
R115
1500
INDEX
S109
R118
2200
DELETE
S112
R121
3900
PLAY
R124
8200
S114
REG_GND
DIAL_B
DIAL_A
EXPOSURE
REG_GND
CONTROL SWITCH BLOCK(SE-1380)is replaced as a block.
So that this PRINTED WIRING BOARD is omitted.
MEMORY MIX
S910
(PANEL OPEN/CLOSE)
CN105
1
OPEN/CLOSE
REG_GND
LCD_LED_ON
D115
XX
D114
XX
D116
XX
S105
R111
1500
END SEARCH
D117
XX
R116
2200
DISPLAY
D118
XX
S110
S107
R119
3900
PB ZOOM
S118
R122
8200
FADER
FP-282
R127
27k
RESET
CN106
D105
UDZS-TE17-8.2B
D119
XX
D102
01ZA8.2(TPL3)
H
1
SP(-)
D101
01ZA8.2(TPL3)
TO
PD-138 BOARD(2/2)
CN5704
THROUGH THE
CP-076 HARNESS
(SEE PAGE 4-91)
R130
1k
CN103 6P
XCS_LCD_DRIVER
LCD_COM/XDATA
OSD_SO
XOSD_SCK
DISP_LCD_VDD
DISP_BL
N.C
SEIDEN_GND
SEIDEN_GND
Q101
2SC4116YG-TE85L
LCD B+ ON/OFF
6.8
XCS_LCD_DRIVER
7.5
3.4
Q102
2SA1362-YG-EL
SWITCHING
SIGNAL PATH
VIDEO SIGNAL
COM/XDATA
CHROMA
OSD_SO
XOSD_SCK
R113
FOCUS_AUTO
2.3
2.9
R106
68
CH GND
DCR-TRV230/TRV330
REG_GND
R108
330
R105
100k
SP_-
R103
220
LND101
REG_GND
CH GND
LCD_LED_ON
D122
XX
SP_+
2P
SP(+)
D121
XX
D120
XX
LND102
C101
0.01u
270
Y/CHROMA
AUDIO
SIGNAL
REC
PB
TO
PD-139 BOARD(2/2)
CN5704
THROUGH THE
CP-076 HARNESS
(SEE PAGE 4-97)

DCR-TRV530
16
CF-079/CF-080 (1/2)
4-75
2P
D106
01ZA8.2(TPL3)
S101
SP901
SPEAKER
6P
D108
R126
27k
OSD_SO
XOSD_SCK
MENU_EXE
EXPOSURE
D113
XX
COM/XDATA
1k
01ZA8.2(TPL3)
S103
R101
XOSD_SCK
R120
3900
TITLE
R125
27k
DIAL_A
DIAL_B
(TRV330/TRV530)
REG_GND
R117
2200
S115
S113
CN107
31
32
R109
1200
S111
MENU_EXE
30
DIAL_B
S108
R114
1500
Q103
RN1104F(TPL3)
LED DRIVE
0
XHI_RESET
S101
EXPOSURE
S102
S102
MENU_EXE
(SEE PAGE 4-48)
USER FUNCTION

(SE-1380)
SEL/PUSH EXEC
EXPOSURE
THROUGH THE
FFC-001 FLAT CABLE
S408
REC
R404
3900
PAUSE
18
S406
FF
S404
VB
R409
1k
S405
R403
2200
XTALLY_LED
D401
(1R)
SUPER NIGHT SHOT
S103/S102
CN101
16
CL001
STOP
15
14
45P
13
FLEXIBLE
VCR SWITCH
USER FUNCTION
CN102
12
FP-275
(DCR-TRV530)

NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
4-76
6P
FLEXIBLE
FOCUS
FOCUS
AUTOMANUAL

Refer to page 4-67 (CF-079), 4-71 (CF-080) for printed wiring board.
CF-079 BOARD(2/2)
CF-080 BOARD(2/2)
EVF DRIVE
1.8
FRP
12.8
1.4
BLACK_IN
PRG
FRP
PFRP
XVP.SAVE
VP
VP_DC_DET
Vcc2
GND1
B_IN
23
22
21
20
19
VREF
15
XP.SAVE
Vcc3
G_IN
COM_OUT
R_IN
COM_IN
EVF_R
TO(1/2)
EVF_VG
C219
1u
B 2012
2.9
R218
390
6.5
R222
33k
XTALLY_LED
EVF_4.75V
CN201
C221
2.2u
B
R219
180k
12.8
TG23
6.3
D202
1T369-01-T8A
TG21
C213
0.1u R214
1M
B
TG17
C215
0.001u
B
L202
C217
120p
6.8uH
2520
CH
SHR
SHG
SHB
SHA
2.8
0.9
0.9
LED_DA
LED_ON/OFF
EVF_GND
EVF_GND
COM
VG
VR
10
VB
11
BLK
12
HCK1
13
HCK2
14
HST
15
EN
16
STB
17
VCK
18
VST
19
EVF_GND
20
EVF_VDD
TO
TG16
TG15
TG14
THROUGH THE
FP-268 FLEXIBLE
(SEE PAGE 4-85)
XP_SAVE
R213
68k
R212
22k
TG22
R215
100k
XC_SAVE
R210
47k
12
2.5
1.1
1.4
1.4
1.4
0.9
SHA
0.9
2.8
SHB
SHR
SHG
11
XTALLY_LED
30
29
28
27
TST2
RPD
XCSAVE
OSCI
2.8
26
25
XPSAVE
31
SHA
1.4
32
OSCO
33
GND
1.4
34
SHB
2.8
35
SHG
1.4
36
SO
STB
SI
VCK
VDO
VST
XVD
TSTEN
HD
1
0.3
10
11
24
23
22
1.4
R229
0
R230
0
0.1
TG23
TG22
TG21
19
20
21
R228
0
2.8
18
EN
17
DWN
XCS
16
VDD
2.6
XHD
VDD
IC202
CXD3501AR-T4
15
XSCK
14
42
43
RGT
R227
0
2.7
TG17
2.8
TG16
1.4
TG15
TG14
VIDEO SIGNAL
CHROMA
Y/CHROMA
REC
PB
13
2.8
XVD
48
47
HST
TIMING GENERATOR
TST4
TG24
1.4
TST1
2.1
FRP
+IN
HI_SO
2.7
HCK2
IC202
-IN
XTG_SO
2.9
44
XCS_EVF
45
2.5
2.8
46
XHI_SCK
SBLK
12
2.8
1.4
HCK1
PWM
FRP
BLK
TST3
LED
TST0
BLK
2.8
HI_SO
GND
38
XHI_SCK
XCLP
DETIN
2.7
XCS_EVF
XWRT
BGP
XVD
37
XHD
41
HI_SO
10
R211 C212
68k 560p
CH
HDO
XHI_SCK
HDO
39
XCS_EVF
R209
2700
C211
XX
B
40
EVF_XVD
2.8
R206
XX
VCO
20P
R207
XX
XSYS_RST
EVF_XHD
0.9
C206
XX
B
SHR
R226
0
EVF_4.75V
CN701
XCLR
C210
0.1u
B
0.9
2.8
FB201
0uH
LB-068/070 BOARD
TG24
2
TO(1/2)
EVF_VR
C220
1u
B 2012
3.6
R221
33k
17
GND2
LPF_ADJ
R217
390
6.5
16
TRAP_ADJ
R220
33k
18
VR_DC_DET
IC201
CXA3579R-T4
VR
DRIVER
Vcc1
R232
0
24
2.7
N.C
EXT_DA
BGP
1.7
R_INJECT
XCS
VG_DC_DET
3.5
14
38
39
SI
C209
0.01u
B
BW_Y
IC201
VG
EVF_VB
C218
1u
B 2012
13
R231
0
VB_DC_DET
R216
390
6.6
COM_DC
EVF_B
VCO
C208
0.01u
B
1.8
25
OP_OUT
C207
0.01u
B
26
OP_IN-
1.8
27
OP_IN+
REG_GND
28
BIAS
2.8
XP_SAVE
29
N.C
1.2
30
SH_A
R205
27k
C202
0.1u
16V
B
31
SH_B
C201
10u
4V
TA A
32
SH_G
2.8
33
SH_R
2.8
EVF_2.8V
37
0
2.9
34
VB
XSH.SAVE
XCS_EVF
40
2.7
35
XSCK
41
XTG_SO
36
XC.SAVE
42
2.5
43
XHI_SCK
44
L201
10uH
2520
2.8
45
EVF_13.3V
XC_SAVE
46
R203
470k
14
C216
0.1u
B
C_BG
47
48
C205
XX
13
C214
3.3u
20V
TA A
R208
XX
BLK
BGP
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
12
11
FB202
0uH
10
(DCR-TRV230/TRV330)
(DCR-TRV530)
CMPO
HDO
16
4-77
4-78
EVF DRIVER
CF-079/CF-080 (2/2)
SI-028 (DCR-TRV230/TRV330), SI-029 (DCR-TRV530) (STEADY SHOT, REMOTE COMMANDER RECEIVER, LASER LINK) PRINTED WIRING BOARDS
Ref. No. SI-028, SI-029 Boards; 1,000 Series
Suffix No.-12
Suffix No.-12, -13

SI-028, SI-029 boards consists of multiple layers.
SI-028 (TRV230/TRV330)
SI-029 (TRV530)
LASER LINK
FP-283
FP-275
(PANEL REVERSE)
(SWITCH)

VC-254
DC/DC CONVERTER
FP-282
(FOCUS)
STEADY SHOT, REMOTE COMMANDER RECEIVER, LASER LINK

SI-028, SI-029
4-80
FP-273 (MIC, HEADPHONES) FLEXIBLE BOARD (DCR-TRV530)

2
3
1
Ref. No. FP-273 Flexible Board; 30,000 Series
SI-028 BOARD
SI-029 BOARD
(DCR-TRV230/TRV330)
(DCR-TRV530)
STEADY SHOT,REMOTE COMMANDER RECEIVER, LASER LINK
10
11
12
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
NO MARK:IR ON/IR OFF MODE
( ):IR ON MODE
[ ]:IR OFF MODE
FP-273
FLEXIBLE
MIC,HEADPHONES
J302
MIC
(PLUG IN POWER)
CN301
14P
EXT_MIC_R
EXT_MIC_R
14
EXT_MIC_L
13
MIC_GND
12
MIC_GND
11
HP_GND
10
HP_L
HP_JACK_IN
EXT_MIC_L
J301
HP_GND
(HEADPHONES)
HP_L
HP_JACK_IN
HP_R
HP_R
REG_GND
MF_B
MF_LED
MF_B
MF_LED
MF_4.75V
REG_GND
MF_A
R301 330
D306
SML-310LTT86
(FRONT TALLY)
CN304
C301
XX
PH301
CNA1312K01S0
CH_GND
VDR302
D302
XX
VDR301
D301
XX
D303
01ZA8.2(TPL3)
LND301
D304
UDZS-TE17-8.2B
MF_A
PH302
CNA1312K01S0
R307
0
2.8V
LIA1
Vref1
FP-273
(MIC, HEADPHONES)
CHROMA
F301
200mA
Y/CHROMA
AUDIO
SIGNAL
4.6
C312
22u
4V
TA A
R313
0
EXT_MIC_L
18
EXT_MIC_R
17
EXT_MIC_GND
16
INT_MIC_GND
15
INT_MIC_R
14
INT_MIC_L
13
REG_GND
12
SE_2.8V
11
IR_DRV_EM
10
SIRCS_SIG
HP_GND
HP_L
HP_R
HP_JACK_IN
MF_LED
A_4.75V
MF_B
MF_A
REG_GND
TO
VC-254 BOARD(17/18)
CN1116
THROUGH THE
FP-226 FLEXIBLE
(SEE PAGE 4-47)
R311
0
D308
CL-310IRS-X-TU
(LASER LINK)
4.7
(5.1)/
[6.4]
CN302
MIC901
L-CH
FP-271 (TRV330/TRV530)
(USB)
SE_GND
19
MF_A
IC301
PNA4S13M02S0
PB
FP-270
LIA1
20
MF_LED
D305
1SS352-TPH3
REC
FP-272
(LANC, DV IN/OUT)
VREF1
21
MF_B
LIA2
LIA2
22
HP_L
2.8V
VIDEO SIGNAL
VREF2
23
HP_JACK_IN
Vref2
SIGNAL PATH
24
26P
HP_R
R315
C304
0
XX
6.3V
TA A
C305
0.1u
B
XF_TALLY_LED
HP_GND
D307
DCW2810
(LASER LINK)

R312
0
L301
10uH
FU-150 (TRV230/TRV330)
FU-154 (TRV530)
(POWER SUPPLY)
Suffix NO.-12 ONLY
C310
0.1u
B
SE302
(YAW SENSOR)
PC-082 (TRV330/TRV530)
DS STILL PROCESS
FB001
0uH
R314
0
C311
22u
3
4V
TA A

FP-273 flexible board consists of multiple layers. However, only the sides (layers) A and B are shown.
VTR_UNREG
25
EXT_MIC_L
FB002
0uH
26
EXT_MIC_R
SE301
(PITCH SENSOR)
R310
1500
Q301
2SD999-T1-CLCK
DRIVER
(1.3)/[0]
INT_MIC_L
GND
INT_MIC_R
GND
MIC
CN303
MIC902
R-CH
IC301
2P
2P
REMOTE COMMANDER
RECIEVER
C306
10u
6.3V
TA A
(0.65)/
[0]
C307
0.1u
B
R308
18
1/16W
1608
MIC
C308
0.1u
B
C309
4.7u
16V
TA A
R309
10
1/10W
2012
16
I
Note :
specified.
4-81
Note :
pour la scurit.
STEADY SHOT, REMOTE COMMANDER RECEIVER, LASER LINK

SI-028, SI-029
/ MIC, HEADPHONES
FP-273
LB-068 (EVF, BACK LIGHT) PRINTED WIRING BOARD (DCR-TRV230/TRV330)
LB-070 (EVF, BACK LIGHT) PRINTED WIRING BOARD (DCR-TRV530)
Ref. No. LB-068, LB-070 Boards; 1,000 Series

LB-068, LB-070 boards consists of multiple layers.
Chip parts
Transistor
65 4
12 3

LB-068 (TRV230/TRV330)
LB-070 (TRV530)
(EVF BACK LIGHT)
CF-079 (TRV230/TRV330)
CF-080 (TRV530)
CD-292 (TRV230/TRV330)
CD-315 (TRV530)
(CCD IMAGER)
PD-138 (TRV230/TRV330)
PD-139 (TRV530)
EVF, BACK LIGHT

LB-068, LB-070
4-83
4-84
FP-283 (PANEL REVERSE) FLEXIBLE BOARD

R705
1k
4.6
Q702
UP04312008S0
BACKLIGHT
ON/OFF SW
D702
SML-310LTT
(TALLY)
4.7
EVF BACKLIGHT DRIVER

IC701
NJM2125F(TE2)
VCC
0.9
(BACKLIGHT)
0.9
4
3
R701
33k
0.5%
0.3
R704
47
0.5%
20P
EVF_4.75V
20
XTALLY_LED
19
LED_DA
18
LED_ON/OFF
17
EVF_GND
16
Q701
UP04601008S0
TH701
6.8k
CN702
SIGNAL PATH
16P
13.1
16
COM
15
VG
14
VR
13
VB
12
BLK
11
HCK1
10
HCK2
VIDEO SIGNAL
0
EVF_GND
15
COM
14
VG
13
VR
12
VB
11
BLK
10
CHROMA
1.4
2.6
LCD903
4.7
HCK1
HCK2
HST
EN
HST
RGT
DWN
EN
Y/CHROMA
REC
2.8
4.7
(SEE PAGE 4-78)
Note :
pour la scurit.
BACKLIGHT DRIVE
0.3
THROUGH THE
FP-268 FLEXIBLE
1.6
0.3
10
4.7
2
0.3
TO
FC-079/080 BOARD(2/2)
CN201
Note :
specified.
D701
NSCW100-T38
R703
3300
R702
180k
0.5%
R706
33k
IC701
2.8
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
(DCR-TRV530)
EVF BACKLIGHT
CN701
(DCR-TRV230/TRV330)
LB-068 BOARD
LB-070 BOARD
Ref. No. FP-283 Flexible Board; 30,000 Series
PB
B/W
LCD UNIT
1.4
1.4
0
STB
STB
VCK
6.5
VCK
VST
EVF_GND
6.5
E
16
EVF_VDD
C702
2.2u
F
2012
VST
VSS
VDD
6.3

FP-283 flexible board consists of multiple layers. However, only the sides (layers) A is shown.

SI-028 (TRV230/TRV330)
SI-029 (TRV530)
LASER LINK
FP-283
FP-275
(PANEL REVERSE)
(SWITCH)
VC-254
DC/DC CONVERTER
FP-282
(FOCUS)
4-85
4-86
EVF, BACK LIGHT

LB-068/LB-070
/ PANEL REVERSE
FP-283
PD-138 (RGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHT DRIVE) PRINTED WIRING BOARD (DCR-TRV230/TRV330)
Ref. No. PD-138 Board; 20,000 Series

PD-138 board consists of multiple layers. However, only
Chip parts
Transistor
C
65 4
12 3

LB-068 (TRV230/TRV330)
LB-070 (TRV530)
(EVF BACK LIGHT)
CF-079 (TRV230/TRV330)
CF-080 (TRV530)
CD-292 (TRV230/TRV330)
CD-315 (TRV530)
(CCD IMAGER)
PD-138 (TRV230/TRV330)
PD-139 (TRV530)
RGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHT DRIVE

PD-138
4-88
Refer to page 4-87 for PD-138 printed wiring board.
(DCR-TRV230/TRV330)
PANEL_B
16
PANEL_G
17
PANEL_R
18
AD5
19
XSYS_RST
20
1.9
C5507
0.01u
TRAP_ADJ
XP.SAVE
N.C
N.C
7
1.4
10
R5506
2700
6P
S601
PANEL_REV
FB5502
0uH
1608
N.C.
N.C.
GND
GND
1.7
C5519
0.1u
B
4.7
R5516
10k
13.6
C5520
6.8u
16V
TA A
CN5501
11
C5523
XX
B
C5521
1u
B
2012
12
R5559
XX
R5512
100k
L5505
27uH
R5510
68k
R5509
22k
D5502
1T369-01-T8A
TG24
C5515
1000p
SL
R5511
1M
C5504
0.1u
B
C5518
0.1u
B
C5522
XX
B
C5512
0.1u
B
C5511
560p
CH
R5508
68k
R5507
47k
1
2
24
Vcc4
FLEXIBLE
PANEL REVERSE
(PANEL REVERSE SW)
23
VSH
N.C
R_IN
22
GND1
B_IN
G_IN
21
GND2
LPF_ADJ
2.3
20
R_DC_DET
IC5501
RB5P003AM1
FP-283
PANEL_REV
VR
DRIVER
Vcc1
C5517
0.1u
B
1.7
R5525 100
Vcc2
G_DC_DET
IC5501
XCS
CN5703
TG23
TG22
C5516
100p
R5513
1M
TG21
TG20
TG19
TG12
R5575
0
TG18
TG17
C5529
XX
B
TG16
XP.SAVE
XC.SAVE
R5572
1k
TG15
TG14
TG13
C5528
1u
R5504
XX
2.8
2.8
SI
GPCK/MODE1
VSYB
STBYB/PSG
GRES/EX1
XVD
10
11
12
CP/SPS
1.2
R5574
0
1.4
C5532
XX
R5570
100k
TG23
TG22
2.8
2.8
TG21
2.3
R5571
1M
R5561
XX
TG20
R5515
0
1.4
Q5509
UN9213J-(K8).SO
SWITCH
TG19
0
R5522
XX
TG16
2.8
TG15
2.8
TG14
2.8
R5565
1M
2.5
2.8
2.8
XHD_OUT 2.7
0.2
XHD
XVD_OUT
GND
21
VB
20
VG
19
VR
18
SPD
17
CLD
16
CTR
15
PSS2
14
PSS1
13
RES
12
CLS
11
VCOM
10
EX2
PSG
MO2
MO1
EX1
SPS
VGLAC
VGL
GND
VGH
VB
XVD_OUT
VG
C5531
0.01u
CN5502 10P
XVD_OUT
TG13
4
R5553
1k
R5518
XX
TG12
PANEL_COM
VR
CPC
MAKER_CHECK
XHD
R5521
0
LCD 901
2.5 INCH
COLOR
LCD UNIT
R5567
XX
(FOR CHECK)
XHD_OUT
7
XHD
22
24P
-15.6
-15.6
TG17
2.8
VSH3V
C5530
0.01u
13.6
R5564
1M
R5563
47k
R5562
10k
TG18
2.8
VSH5V
23
-15.0
R5573
0
R5566
XX
4.0
TG24
Q5511
UP04601008S0
SWITCH
0.1
13.6
24
4.7
2.8
24
23
22
21
20
19
18
17
GSRT/MODE2
16
1.3
OSCO
DR.P.SAVE
1.4
OSCI
2.8
PD
PS/VDD
XC.SAVE
1.4
2.8
GND
-IN/TESTO
SO
CPMODE/CLS
XVD
XCS
TESTI
2.8
RESET/EX2
TESTI
0.2
VDD/TESTI
PWM
XHI_SO
IC5502
LZ9FF474
LED
2.7
VDD/RES
TESTI/GND
XTG_SO
SRT/PSS1
TIMING GENERATOR
GND/TESTI
2.8
OE/PSS2
IC5502
C5524
1u
B
2012
Q5502
MGSF1P02LT1
B+ SWITCH 4.7
R5514
XX
CLR/CTR
BL-DET
XCS_LCD
XSCK
R5568
XX
HCNT/SPD
BL-ON
2.8
COM_FRP
25
MCLK/CLD
HDB
2.5
26
HDI
XHI_SCK
27
15
FRP
41
1.4
42
1.4
COM_FRP
43
FRP
28
44
PB
29
14
SW
30
45
0.1
BLK
31
46
REC
32
13
SWCOM
Y/CHROMA
33
+IN/TESTO
POCB
37
BGP
34
Q5510
UP04601008S0
SWITCH
47
2.7
48
CHROMA
BGP
38
VIDEO SIGNAL
39
SIGNAL PATH
C5508
0.1u
B
40
R5560
XX
Q5501
XX
35
SYF
36
OUT/TESTO
2.8
2.8
XSYS_RST
18
4.7
13.6
Vcc3
6.8
N.C
COM_OUT
COM_FRP
SI
VG
19
FRP
FRP
1.4
GND3
1.4
BLACK_IN
2.7
N.C
BGP
EXT_DA1
XSCK
18
37
COM_FRP
BGP
1.8
C5506
0.01u
XSYS_RST
17
1.7
R5524 100
PANEL_XHD
2.8
XP.SAVE
C5505
0.01u
1.8
16
2.3
R5523 100
PANEL_XVD
B_DC_DET
D5503
MA111-(K8).S0
15
1.1
R5503
100k
0.5%
XC.SAVE
17
PANEL_XHD
15
2.3
16
14
XHI_SO
VB
15
PANEL_XVD
XS_LCD
EXT_DA2
14
13
25
13
12
XHI_SO
R5502
XX
26
N.C
XCS_LCD
C5501
22u
4V
TA A
2.8
27
VCO
11
R5557
0
28
OP_OUT
XHI_SCK
2.8
REG_GND
XHI_SCK
29
3.1
9
10
2.8
30
OP_IN-
(SEE PAGE 4-24)
REG_GND
REG_GND
14
C5513
0.1u
B
C5510
0.1u
B
1.5
THROUGH THE
VP-076 HARNESS
XCS_LCD
31
1.4
PANEL_2.8V
32
OP_IN+
C5503
0.1u
B
33
BIAS
PANEL_2.8V
TO
VC-254 BOARD(5/18)
CN1120
L5501
10uH
2520
34
1.4
PANEL_4.75V
R_INJECT
1.1
2.7
35
N.C
XTG_SO
36
N.C
R5501
470k
PANEL_13.3V
PANEL_4.75V
2.5
38
XHI_SCK
39
PANEL_-15.3V
1 TO(2/2)
40
BL_CONT
41
42
BL_CONT
43
BL_REG
44
2.8
45
BL_REG
1.6
XC.SAVE
46
BL_GND
47
SE_GND
48
DAC
1
BL_GND
13
C5514
10u
6.3V
TA A
*
C5509
1u
C5527
0.01u
B
0.7
1.7
R5505
15k
R5569
180k
SE_GND
12
1608
L5504
XX
2520
N.C
FB5504 0uH
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
BLK
20P
11
FB5503
0uH
1608
RGB DRIVE,TIMING GENERATOR
CN5701
10
0.2
PD-138 BOARD(1/2)
A
N.C
N.C
XHD
XHD_OUT
GND
10
GND
R5517
XX
16
BL_ON
R5551
47k
LED
2 TO(2/2)
DETIN
4-89
4-90
RGB DRIVE, TIMING GENERATOR

PD-138 (1/2)

SEG11
SEG12
1.5
SEG14
SEG13
1.5
COM1
22P
COM2
SEG3
SEG4
SEG5
SEG6
SEG2
SEG7
SEG8
10
SEG9
11
SEG10
12
SEG1
13
SEG15
14
SEG16
15
SEG11
16
SEG12
17
SEG13
18
SEG14
19
COM3
20
COM4
21
BL_VDD
22
BL_GND
FP-276
FLEXIBLE
COM2
OSD_SO
SO
THROUGH THE
CP-076 HARNESS
DISP_BL
5
SCK
SO
2.8
DISP_LCD_VDD
3.0
2.8
XOSD_SCK
SCK
SEG11
SEG12
SEG13
SEG14
SEG10
OSC1
IC5701
OSC2
VSS
LCD DRIVER
VC
IC5701
BU9735K-E2
17 18 19 20 21 22 23 24
SEG15
SEG18
LCD_COM/XDATA
1.6
SEG6
10
1.6
XCS_LCD_DRIVER
XCS C5704
0.1u
B
C/XD
SEG5
LCD902
CHARACTER
DISPLAY
UNIT
SEG2
6P
SEG16
SEG4
CN5704
(SEE PAGE 4-75)
CN5705
COM1
10
SEG3
R5712
680k
32 31 30 29 28 27 26 25
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
TO
CF-079/080 BOARD(1/2)
CN103
1.5
1.5
SEG17
SEG15
SEG16
(DCR-TRV230/TRV330)
LCD DRIVE,BACKLIGHT DRIVE
1.5
PD-138 BOARD(2/2)
1.5
SEG9
SEG8
SEG7
SEG6
VLCD
SEG5
VDD
SEG4
SCK
SEG3
SD
1.5 SEG10
SEG7
1.5
SEG9
SEG8
1.5
SEG8
SEG9
1.5
SEG7
SEG10
1.5
SEG6
SEG1
1.5
SEG5
SEG15
1.5
1.5
SEG4
SEG16
SEG3
SEG11
SEG12
SEG2
SEG1
COM4
COM3
COM2
COM1
XCS
C/XD
SEG13
SEG14
COM3
COM4
1.5
1.5
SEG2
1.5
SEG1
1.5
COM4
1.5
COM3
COM1
C/XD
COM2
1.5
2.9
XCS
10 11 12 13 14 15 16
D902
BACKLIGHT
BL_REG
R5610
1800
1/10W
2012
L5601
100uH
R5613
1800
1/10W
2012
5
1
6
C5603
XX
B
2012 3
16V
-0.5
C5602
4.7u
B
3216
C5607
12p
3kV
10
T5601
-0.5
INVERTER
TRANSFORMER
Q5602
FP216-TL
SWITCHING
TO(1/2)
BL_HIGH
N.C
N.C
N.C
N.C
N.C
4
Q5603
UP04312008S0
LED DRIVE
PANEL_4.75V
PANEL_2.8V
IC5602
TA75S393F-TE85R
ND901
BACKLIGHT
2.8
VCC
2.8
LED
LED_GND
D901
(STARTER)
4.7
D5601
MA111-(K8).S0
R5611
180k
2.2
R5619
XX
BL_LOW
0.33
CURRENT DETECT
N.C
IC5602
R5616
100
4.6
CN5604 10P
10
BL_GND
4.6
4.6
2
C5604
0.015u
B
2012
C5605
0.1u
B
R5617
22k
C5606
0.1u
B
R5618
470
LND705
R5612 22k
D5603 XX
DAC
REG_GND
3
DETIN
4
Q5601
UN9213J-(K8).SO
INV
TO(1/2)
CH0
INH
CH1
VEE
2.8
BL_ON
COM
VCC
A
GND
2.8
SELECT SWITCH
1.6
R5614
10k
BL_CONT
1.6
IC5601
TC7W53FU(TE12R)
R5609
10k
D5604
XX
2.8
SE_GND
CH_GND
IC5601
XX
R5620
Note :
specified.
LED

PD-138 (2/2)
4-91
16
4-92
Note :
pour la scurit.
PD-139 (RGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHT DRIVE) PRINTED WIRING BOARD (DCR-TRV530)
Ref. No. PD-139 Board; 20,000 Series

PD-139 board consists of multiple layers. However, only
Chip parts
Transistor
C
65 4
12 3

LB-068 (TRV230/TRV330)
LB-070 (TRV530)
(EVF BACK LIGHT)
CF-079 (TRV230/TRV330)
CF-080 (TRV530)
CD-292 (TRV230/TRV330)
CD-315 (TRV530)
(CCD IMAGER)
PD-138 (TRV230/TRV330)
PD-139 (TRV530)
4-93
RGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHT DRIVE

PD-139
Refer to page 4-93 for PD-139 printed wiring board.
2
1
PD-139 BOARD(1/2)
(DCR-TRV530)
RGB DRIVE,TIMING GENERATOR
10
12
11
13
14
16
15
L5504
XX
2520
FB5504
1608
FRP
C5509
3.3u
20V
TA A
C5510
0.1u
B
PFRP
PRG
BGP
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
BLK
REG_GND
10
XHI_SCK
XHI_SCK
11
XCS_LCD
12
XCS_LCD
XHI_SO
XHI_SO
13
XVD
PANEL_XVD
14
PANEL_XHD
15
PANEL_B
16
PANEL_G
17
PANEL_R
18
AD5
19
XSYS_RST
20
L5501
10uH
2520
C5501
22u
4V
TA A
R5557
0
C5503
0.1u
R5502
B
XX
2.8
R5558
XX
R5503
82k
XHD
1.2
XP.SAVE
C5505
0.01u
2.8
1.8
C5506
0.01u
1.8
C5507
0.01u
1.8
24
2.8
PRG
1.4
FRP
1.4
PFRP
2.8
XVP.SAVE
7.1
VP
12.8
Vcc2
0
BLACK_IN
2.8
P_DC_DET
N.C
2.7
BGP
VG
IC5501
G_DC_DET
VR
DRIVER
R_DC_DET
TRAP_ADJ
LPF_ADJ
XP.SAVE
B_IN
G_IN
R_IN
IC5501
CXA3579R-T4
GND2/N.C.
GND1
VREF
Vcc3
COM_OUT
COM_IN
7.2
C5517
1u B 2012
SH_G
SH_B
SH_A
GND/N.C.
BIAS
OP_IN+
OP_IN-
OP_OUT
VCO
COM_DC
FLEXIBLE
SH_R
FP-283
XSH.SAVE
10
11
12
R5577
470k
7.2
3.1
C5518
1u B 2012
7.2
2.9
C5519
1u B 2012
12.8
C5538
0.01u
B
Q5506
UN9213J-(K8).SO
TG14
2.8
C5539
XX
20V
TA
A
C5537
XX
B
R5587
33k
12.8
R5588
180k
R5586
33k
R5585
33k
C5533
4.7u
B
3216
XSYS_RST
Q5505
NDS356AP
12.8
2.8
23
Vcc1
VB
B_DC_DET
22
XCS
R5571 100
2.8
C5532
1u
B
2012
R5523 100
2.9
25
21
XCS_LCD
26
R5524 100
PANEL_2.8V
SI
27
R5525 100
2.5
28
20
REG_GND
R5501
470k
29
19
PANEL_2.8V
XTG_SO
PANEL_4.75V
30
18
XSCK
31
17
PANEL_4.75V
2.5
XC.SAVE
32
16
(SEE PAGE 4-24)
PANEL_13.3V
XHI_SCK
N.C./C_BG
33
15
TO
VC-254 BOARD(5/18)
CN1120
THROUGH THE
VP-076 HARNESS
2.8
34
14
REG-GND
XC.SAVE
35
13
(2/2)
37
PANEL_-15.3V
38
BL_CONT
39
BL_REG
40
41
BL_REG
BL_CONT
C5527
XX
B
42
BL_GND
43
44
SE_GND
BL_GND
45
46
SE_GND
47
DAC
20P
48
CN5701
36
1.4
EXT_DA
0
N.C./R_INJECT
R5505
XX
CN5501
24P
24
TEST1
23
COM
22
VST
21
VCK
20
EN
19
DWN
18
VDD
17
VSS
16
VDOG
15
VVSSG
14
CS
13
WIDE
12
HST
11
REF
10
SOUT
CRext
HCK2
HCK1
PSIG
RGT
TEST2
TG24
CN5703 6P
GND
2.7
1.3
1.4
1.4
R5507
47k
R5509
22k
C5504
0.1u
B
R5512
100k
C5512
0.1u
B
6
FB5502
0uH
1608
TG22
R5508
68k
SH4
GND
SH3
SH2
6.9
C5511
560p
CH
N.C.
SH1
(PANEL REVERSE SW)

N.C.
1.4
0.9
R5506
2700
PANEL_REV
0.9
S601
2.8
2.8
0.9
TG23
PANEL REV
TG21
D5502
1T369-01-T8A
C5515
1000p
SL
R5511
1M
R5510
68k
D5503
RD3.3UM-T1B
C5516
100p
50V
CH
L5505
6.8uH
TG20
R5579
C5534
1u
B
2012
C5540
0.1u
B
150k
LCD901
3.5 INCH
COLOR
LCD UNIT
VIDEO SIGNAL
Y/CHROMA
XP.SAVE
XC.SAVE
SH4
2.8
1.4
25
XSTBY
1.4
26
OSCO
2.8
27
OSCI
PFRP
TG15
VCK
EN
IC5502
DWN
TIMING GENERATOR
WIDE
XSCK
VDD
R5573
10k
TG24
1.4
TG23
2.6
TG22
2.8
TG21
0.1
TG20
Q5503
UP04601008S0
SWITCH
7.1
R5576
1M
7.7
7.7
HST
R5589
XX
7.1
2.8
CN5502 10P
XVD-OUT
TG18
GND
TST0
LED
PWM
TEST
TEST
TEST
10
11
12
17
16
14
TSTEN
13
15
POFF
1.4
R5591
0 TG16
1.4
2.8
R5592
0 TG15
2.8
TG14
XVD_OUT
R5551
47k
VB
XVD_OUT
VG
PSIG
VR
MAKER_CHECK
7.1
TG17
12.8
Q5508
UP04601008S0
SWITCH
XHD
XHD-OUT
R5553
47k
XHD
XHD_OUT
GND
10 GND
LED
BL_ON
DETIN
L
16
4-95
R5575
68k
6.5
XHD
PD-139 (1/2)
1.5
Q5504
2SB1462J-QR(K8).SO
SWITCH
R5572
10k
DETIN
2.8
7
BL_ON
XVD
2.8
VDO
RGT
XWRT
2.8
XVD
SI
HDO
0.3
2.1
HCK1
XHD_OUT
XHI_SO
PB
SO
HD
2.6
HCK2
2.6
XTG_SO
XCS
XHD
2.9
XCS_LCD
R5574
820k
0.9
C5536
0.1u
B
6.5
IC5502
CXD3516R-T4
VDD
23
VST
24
12.8
22
1.4
XC.SAVE
2.8
TEST
VSS
RPD
0.9
SH3
2.8
0.9
SHA
28
21
37
29
7.1
REC
FRP
44
SBLK
45
CHROMA
2.8
30
20
2.5
31
19
XHI_SCK
32
18
1.4
38
PFRP
39
1.4
40
FRP
33
PRG
41
46
2.8
34
TG17
TG16
XCLP
47
SIGNAL PATH
PRG
BLK
42
BGP
43
2.7
48
XCLR
C5508
0.1u
B
35
SHB
36
SHG
R5560
XX
SHR
Q5501
XX
0.9
SH1
XSYS_RST
R5504
XX
2.8
R5590
1k
C5529
XX
B
SH2
TG18
4-96
(2/2)
CPC
(FOR CHECK)

SEG15
SEG14
SEG13
SEG12
SEG11
1.5
1.5
1.5
1.5
(DCR-TRV530)
LCD DRIVE,BACKLIGHT DRIVE
FP-277
CN5705
COM1
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
11
10
32 31 30 29 28 27 26 25
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
COM1
COM2
SEG3
SEG4
SEG5
SEG6
SEG2
SEG7
SEG8
10
SEG9
11
SEG10
12
SEG1
13
SEG15
14
SEG16
15
SEG11
16
SEG12
17
SEG13
18
SEG14
19
COM3
20
COM4
21
BL_VDD
22
BL_GND
22P
FLEXIBLE
COM2
10
1.6
XCS
XCS_LCD_DRIVER
OSC2
C/XD
2
SO
3
4
DISP_LCD_VDD
SCK
SO
2.8
SEG6
SEG5
VDD
SEG4
DISP_BL
2.8
SEG7
SEG8
VLCD
3.0
SCK
LCD DRIVER
IC5701
BU9735K-E2
VC
SCK
SEG3
(SEE PAGE 4-75)
IC5701
SEG9
VSS
OSD_SO
XOSD_SCK
C5704
0.1u
B
LCD_COM/XDATA
SEG10
OSC1
2.0
2
TO
CF-079/080 BOARD(1/2)
CN103
THROUGH THE
VP-076 HARNESS
6P
SD
17 18 19 20 21 22 23 24
SEG3
R5712
680k
CN5704
6
SEG16
1.5
PD-139 BOARD(2/2)
A
1.5
1.5 SEG10
1.5
SEG9
1.5
SEG8
1.5
SEG7
1.5
SEG6
1.5
SEG5
1.5
SEG4
1.5
SEG3
SEG4
SEG5
SEG6
SEG2
SEG7
SEG8
SEG9
LCD902
CHARACTER
DISPLAY
SEG10
SEG1
SEG16
SEG2
SEG1
COM4
COM3
COM2
XCS
C/XD
COM1
SEG15
SEG11
SEG12
10 11 12 13 14 15 16
BL_REG
R5610
1800
1/10W
2012
L5601
100uH
10
TO(1/2)
Q5602
FP216-TL
SWITCHING
R5616
100
0.2
4.7
PANEL_2.8V
R5611
180k
IC5602
TA75S393F-TE85R
5
2.8
3
1.4
4
R5619
XX
D902
BACKLIGHT
C5606
0.1u
B
R5612
22k
D5603
XX
1.5
1.5
SEG2
1.5
SEG1
1.5
COM4
9
N.C
N.C
N.C
N.C
N.C
10P
BL_HIGH
ND901
BACKLIGHT
Note :
specified.
Note :
pour la scurit.
N.C
BL_LOW
LED
LED_GND
D901
(STARTER)
4.7
D5601
MA111-(K8).S0
CURRENT
DETECT
0.4
VCC
Q5603
UP04312008S0
LED DRIVE
0.2
C5605
0.1u
B
IC5602
C5607
12p
3kV
T5601
INVERTER
TRANSFORMER
0.2
PANEL_4.75V
2.8
10
BL_GND
1.5
CN5604
4
2
C5603
XX
B
COM4
3.9
3.9
C5604
0.015u
B
2012
3
C5602
4.7u
B
3216
COM3
1
2
0.2
SEG14
5
R5613
1800
1/10W
2012
COM3
COM1
C/XD
COM2
1.5
2.9
XCS
SEG13
R5618
470
LND705
H
16
3
4
TO(1/2)
LED
Q5601
UN9213J-(K8).SO
INV.
4-97
CH0
INH
2.8
BL_ON
REG_GND
DETIN
VCC
COM
CH1
VEE
A
GND
2.8
IC5601
SELECT SWITCH
1.4
1.4
R5614
15k
2.8
6
BL_CONT
IC5601
TC7W53FU(TE12R)
R5609
10k
D5604
XX
CH_GND
0
5
SE_GND
R5620
XX
DAC
R5617
22k
4-98

PD-139 (2/2)
FU-150 (POWER SUPPLY) PRINTED WIRING BOARD (DCR-TRV230/TRV330)
FU-154 (POWER SUPPLY) PRINTED WIRING BOARD (DCR-TRV530)
Ref. No. FU-150, FU-154 Boards; 1,000 Series

FU-150, FU-154 boards consists of multiple layers.
Chip parts
Transistor
C
Diode
65 4
12 3

PC-082 (TRV330/TRV530)
DS STILL PROCESS
FU-150 (TRV230/TRV330)
FU-154 (TRV530)
(POWER SUPPLY)
FP-273
(MIC, HEADPHONES)
FP-272
(LANC, DV IN/OUT)
FP-270
POWER SUPPLY
FU-150/FU-154
FP-271 (TRV330/TRV530)
(USB)
4-99
4-100

FU-150 BOARD
FU-154 BOARD
12
11
10
(DCR-TRV230/TRV330)
(DCR-TRV530)
CN403
ZOOM_VR_AD
POWER SUPPLY
L401
4.7uH
3225
F404
1.4A
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
XS/S_SW
XCZM_MODE_SW
F403
1.4A
6P
BATT/XEXT
BATTERY
TERMINAL
ACV_GND
ACV_UNREG
BATT_SIG
BATT_UNREG
XPHOTO_MODE_SW
F405
*
LF401
XX
DC IN
XPJECT_SW
F402
1.4A
R408
10
1/8W
3216
2
8.1
1
8.3
7.7
R409
1k
KETY_AD1
XPHOTO_FREEZE
F406
1.4A
8
C401
0.1u
B
8.3
R430 R406
0
470k
C402
0.1u
B
5
6
3
4
7.8
8.1
R410
6800
0.1
F401
1.4A
2.9
8.3
C403
0.022u
B
Q404
RN1104F(TPL3)
SWITCH
C404
22u
16V
TA B
Q411,412
SWITCH
C407
XX
F
Q412
*
0
Q411
*
R425
Q401
SSM3K03FE(TPL3)
SWITCH
C405
22u
16V
TA B
C406
22u
16V
TA B
R426
*
D402
01ZA8.2(TPL3)
8.3
D401
1SS357-TPH3
R407
1M
C410
*
B
R420
*
BATT_GND
Q403
2SB1122-ST-TD
SWITCH
Q402
HAT1054R-EL
8.3
SWITCH
R429
0
R401
1k
D408
1SS357-TPH3
CN401
BT901
XVTR_MODE_SW
8.3
13
14
48P
ZOOM_VR_AD
BATT_SIG
FAST_CHARGE
SHOE_ON
BATT/XEXT_SW
XS/S_SW
XCAM_MODE_SW
XVTR_MODE_SW
XEJECT_SW
10
XPHOTO_MODE_SW
11
KEY_AD1
12
XPHOTO_FREEZE
13
D_2.8V
14
INIT_CHARGE_ON
15
BATT_UNREG
16
BATT_UNREG
17
C/D_VS_D1.5V
18
C/D_VS_D1.5V
19
C/D_VS_D1.5V
20
C/D_VS_D1.5V
21
BL_REG_UNREG
22
BL_REG_UNREG
23
BL_REG_UNREG
24
BL_REG_UNREG
25
VTR_UNREG
26
VTR_UNREG
27
VTR_UNREG
TO
VC-254 BOARD(17/18)
CN1113
(SEE PAGE 4-48)
0
R427
*
Q405
RN1104F(TPL3)
SHOE ON
SW
8.3
8.3
Q408
*
SWITCHING
0
D405
01ZA8.2(TPL3)
D404
UDZS-TE17-8.2B
Q409
2SJ305(TE85L)
8.3
Q409,410
SWITCH
8.3
8.3
C409
1u
B
2012
R428
XX
Q410
RN2104F(TPL3)
8.3
R424
47k
R421
*
R423
100
R422
1M
Q407
*
SWITCHING
D407
01ZA8.2(TPL3)
D406
01ZA8.2(TPL3)

(SS-1380)
VTR_UNREG
29
SHOE_GND
30
SHOE/PRT_UNREG
31
SHOE_GND
32
SHOE/PRT_UNREG
33
SHOE_GND
34
SHOE/PRT_UNREG
35
SHOE_GND
36
PRT_HEAD_UNREG
37
REG_GND
38
PRT_HEAD_UNREG
8.3
28
39
REG_GND
40
PRT_HEAD_UNREG
41
REG_GND
42
REG_GND
43
REG_GND
44
REG_GND
45
REG_GND
46
REG_GND
47
REG_GND
48
REG_GND
*MARKED:MOUNT TABLE
MEMORY
TRV330/TRV530
TRV230
C410
1U
XX
F405
1.4A
XX
Q407
XX
MGSF3455VT
Q408
HAT1054R-EL
XX
Q411
RN2104F(TPL3)
XX
Q412
2SJ305(TE85L)
XX
R420
1k
XX
R421
1k
XX
R425
100
XX
R426
1M
XX
R427
47k
XX
CN402 12P
S001
CAMERA
POWER
OFF
MEMORY
REG_GND
XPHOTO_STBY_SW
XCAM_MODE_SW
VTR
CAMERA
XVTR_MODE_SW
XVIR_MODE_SW
XPHOTO_MODE_SW
XCAM_MODE_SW
XS/S_SW
REG_GND
KEY_AD1
XPHOTO_FREEZE
REG_GND
D_2.8V
10
XS/S_SW
START/STOP
OFF(CHG)
KEY_AD1
VCR
ZOOM_VR
(PHOTO FREEZE)
XEJECT_SW
S003
S004
PHOTO
ZOOM_VR
11
R403
1k
12
Note :
pour la scurit.
XEJECT_SW
LND401
GND
OPEN/EJECT
R001
1k
XPHOTO_FREEZE
R402
0
2012
Note :
specified.
LND402
GND
LND001
RV001
20k
SEIDEN GND
W
CONTROL SWITCH BLOCK(SS-1380)is replaced as a block.

So its PRINTED WIRING BOARD is omitted.
J
16
4-101
4-102
POWER SUPPLY
FU-150/FU-154
4-3. WAVEFORMS
CD-292/315 BOARD
VC-254 BOARD
CAMERA REC
1 IC1502 2 qa
1 IC501 1,2
qj IC2201 <z.,
9 IC2201 yj
REC
ra IC3701 7
ed IC4803 r;
wg IC3301 <zc.
CAMERA REC/PB
CAMERA REC/PB
rl IC3701 rk
CAMERA REC/PB
S JACK IN
CAMERA REC/PB
CAMERA REC/PB
LINE REC (S-C IN)
0.46Vp-p
H
6.8Vp-p
2.8Vp-p
3.2Vp-p
56 nsec
80 nsec
2.8Vp-p
74 nsec
q; IC2201 ul
2 IC1502 qh
2 IC501 3,4
wh IC4401 qh
0.3Vp-p
LINE REC (VIDEO IN)
CAMERA REC/PB
S JACK IN
CAMERA REC/PB
t; IC3701 rs
rs IC3701 qf
ef IC4803 td
CAMERA REC/PB
CAMERA REC
3.6Vp-p
50 nsec
40.6 nsec
qk IC3103 1,2,6,7
CAMERA REC/PB
3.6Vp-p
4.5Vp-p
6.8Vp-p
H
3 IC501 7
300 nsec
qa IC2201 <zzx ,<zzv ,<zzm ,<zz.
REC
CAMERA REC
80 nsec
0.6Vp-p
4 IC1501 5
4 IC501 qs
qs IC2201 <zxx ,<zxv ,<zxm ,<zx. ,<zcx ,
CAMERA REC/PB
<zcv ,<zcm ,<zc. CAMERA REC
3.3 msec
50 nsec
wk IC4401 ed
eh IC5701 qf
CAMERA REC/PB
56 nsec
36 MHz
80 nsec
5 IC1501 qa
5 IC501 qd,qf
2.8Vp-p
13.3msec
rf IC3701 wf
ts IC1301 yf
CAMERA REC/PB
3.6Vp-p
14.3181 MHz
56 nsec
6 IC1501 wa
6 Q501 E
0.6Vp-p
2.8Vp-p
56 nsec
rj IC3701 eh
el IC3901 ra
CAMERA REC/PB
3.4Vp-p
34 nsec
wf IC3301 <zzc
qh IC2201 <z,b
LINE REC
CAMERA REC/PB
IR ON
12.5 sec
0.6Vp-p
2.8Vp-p
es IC4501 yl
CAMERA REC/PB
CAMERA REC/PB
CAMERA REC
rk IC3701 el
r; IC3701 rh
CAMERA REC/PB
CAMERA REC/PB
AV JACK or S JACK IN
LINE REC (S-Y IN)
6.8Vp-p
74 nsec
WAVEFORMS
0.5 sec/div
1.4Vp-p
2.8Vp-p
8 IC1501 wk
CD-292, CD-315, VC-254
0.47Vp-p
H
0.9Vp-p
6.8Vp-p
H
LINE REC
3.4Vp-p
ea IC4501 yk
CAMERA REC/PB
CAMERA REC
CAMERA REC
rh IC3701 ef
CAMERA REC/PB
IR ON
2.2 msec
30 nsec
2.2Vp-p
H
ek IC3901 ws
CAMERA REC/PB
wd IC3301 rg
qg IC2201 <zvn
7 IC1501 wh
e; IC4401 tj,tl,ya
2.0Vp-p
6.0Vp-p
2.2 sec
0.2Vp-p
3.5795 MHz
4-103
2.8Vp-p
0.52Vp-p
2.8Vp-p
23.8 nsec
12.5 sec
2.8Vp-p
0.75Vp-p
0.52Vp-p
CAMERA REC/PB
AV JACK IN
0.96 sec
CAMERA REC
CAMERA REC
rg IC3701 ws
CAMERA REC/PB
2.8Vp-p
24 nsec
ws IC3103 rs
qf IC2201 <zvv
CAMERA REC
ej IC3901 7
2.4Vp-p
3.2Vp-p
33.3 msec
6.8Vp-p
250mVp-p
300 nsec
CAMERA REC/PB
CAMERA REC
CAMERA REC
0.96 sec
2.8Vp-p
0.75Vp-p
2.2 sec
IR ON
CAMERA REC/PB
wl IC4401 ra
wa IC3103 r;
qd IC2201 <zvx
CAMERA REC/PB
2.8Vp-p
CAMERA REC/PB
3.6Vp-p
3.6Vp-p
4.6Vp-p
ta IC1301 tk
CAMERA REC/PB
S JACK IN
2.8Vp-p
13.3 msec
CAMERA REC/PB
rd IC3701 qk
CAMERA REC/PB
2Vp-p
400mVp-p
w; IC3103 eg
1.1Vp-p
eg IC4902 1
CAMERA REC/PB
CAMERA PB
0.5Vp-p
3.0Vp-p
30.5 sec
2.2 msec
ql IC3101 rs, IC3103 wj,wl wj IC4401 ws
2.8Vp-p
1.3Vp-p
2.8Vp-p
5.7Vp-p
3 IC1502 ef
H
H
13.3 msec
3.2Vp-p
56 nsec
0.46Vp-p
H
4-104
PC-082 BOARD
CF-079/080 BOARD
PD-138 BOARD (1/2)
REC/PB
1 IC1155 <zcv
3.6Vp-p
20.8 nsec
1 IC5501 rk
1 IC201 w;
2H
7.2Vp-p
9 IC5502 wh
0.5Vp-p
H
6 MHz
3.0Vp-p
2 IC5501 rj
2 IC201 ws
7.2Vp-p
2H
0.5Vp-p
H
3 IC5501 rh
3 IC201 wf
7.2Vp-p
0.5Vp-p
H
2H
4 IC5501 w;
4 IC201 rk
3.0Vp-p
2H
0.50Vp-p
2H
5 IC5501 ws
5 IC201 rj
3.0Vp-p
0.43Vp-p
2H
2H
6 IC5501 wf
6 IC201 rh
3.0Vp-p
0.5Vp-p
2H
2H
7 IC5502 1
7 IC202 wh
2.8Vp-p
2.2Vp-p
10.86 MHz
8 IC5502 rk
2.8Vp-p
V
4-105
WAVEFORMS
PC-082, CF-079, CF-080, PD-138
PD-139 BOARD (1/2)
PD-138/139 BOARD (2/2)
REC/PB
1 IC5501 w;
8.0Vp-p
0 IC5701 2
9 IC5502 wh
25.346 kHz
4.7Vp-p
85 nsec
2 IC5501 ws
8.0Vp-p
3 IC5501 wf
8.0Vp-p
4 IC5501 rk
600mVp-p
H
5 IC5501 rj
600mVp-p
H
6 IC5501 rh
600mVp-p
H
7 IC5502 1
2.8Vp-p
H
8 IC5502 rk
2.8Vp-p
V
WAVEFORMS
PD-138, PD-139
4-106
3.0Vp-p
4-4. MOUNTED PARTS LOCATION

CD-292/315 BOARD (SIDE A)
VC-254 BOARD (SIDE A)
C502
C503
C507
C508
C509
C510
C511
B-1
A-1
B-2
A-1
B-1
A-1
A-1
D001
A-1
C1320
C1328
C1333
C1334
C1336
C1337
C1338
C1340
C1342
C1343
C1347
C1356
C1357
C1358
C1359
C1362
C1508
C1513
C1514
C1515
C1516
C1517
C1518
C1519
C1520
C1521
C1522
C1523
C1524
C1525
C1526
C1551
C1554
C1556
C1561
C1563
C1569
C2002
C2003
C2005
C2006
C2007
C2008
C2009
C2010
C2011
C2012
C2014
C2015
C2016
C2017
C2201
C2202
C2203
C2204
C2208
C2210
C2211
C2212
C2213
C2214
C2215
C2222
C2223
C2224
C2225
C2226
C2227
C2228
C2229
C2230
C2231
C2232
C2233
C2234
C2235
C2236
C2238
C2240
C2242
C2243
C2244
C2247
C2250
C2251
FB5501 B-2
FB5502 B-1
L502
B-1
Q501
A-1
R501
R503
R504
R505
R506
A-1
B-2
A-1
B-1
A-1
CD-292/315 BOARD (SIDE B)

CN501 A-4
IC501
B-4
B-6
B-8
B-6
C-6
A-6
A-8
B-8
B-6
B-8
A-6
A-6
A-6
B-9
A-9
A-8
A-8
F-4
F-3
E-3
F-3
E-3
E-3
E-3
E-3
E-3
E-4
E-4
E-3
F-4
F-3
F-4
C-2
C-2
C-2
D-4
D-3
D-2
A-2
A-1
A-2
A-2
A-1
B-2
A-1
B-2
A-2
A-1
B-1
B-2
A-1
A-1
C-3
C-3
D-4
D-4
D-3
D-4
D-4
C-4
D-4
E-4
D-4
D-4
D-4
D-4
E-4
D-4
D-4
E-4
D-4
C-4
C-4
F-4
F-4
C-4
C-4
F-5
F-6
F-6
D-7
E-7
F-5
C-5
F-5
C-6
C3121
C3122
C3123
C3124
C3126
C3127
C3128
C3129
C3131
C3133
C3134
C3135
C3136
C3138
C3139
C3140
C3601
C3603
C3604
C3608
C3610
C3611
C3612
C3614
C3615
C3616
C3617
C3618
C3619
C3620
C3622
C3626
C3629
C3631
C3633
C3634
C3636
C3701
C3702
C3704
C3705
C3706
C3707
C3708
C3709
C3710
C3711
C3712
C3714
C3715
C3716
C3717
C3719
C3723
C3724
C3728
C3729
C3730
C3731
C3732
C3733
C3734
C3735
C4401
C4402
C4403
C4404
C4405
C4406
C4407
C4408
C4409
C4410
C4411
C4412
C4413
C4414
C4415
C4416
C4417
C4418
C4419
C4420
C4421
C4422
F-5
F-5
F-4
F-4
F-5
F-5
G-4
G-4
F-5
F-5
F-6
F-6
F-6
F-5
G-6
F-5
B-4
B-4
B-3
B-4
A-6
B-5
B-5
B-5
B-5
B-5
B-5
B-5
B-5
B-5
B-4
B-6
B-6
C-4
C-4
C-5
B-4
C-4
B-3
B-4
C-4
C-4
C-4
B-4
B-4
C-4
B-4
C-4
C-4
C-4
C-4
B-4
C-3
C-3
C-3
B-3
C-3
C-3
C-3
B-2
C-2
B-3
B-3
F-7
G-3
F-7
F-7
F-7
F-7
F-7
E-7
F-7
G-4
F-7
F-7
F-7
G-3
E-7
E-7
F-7
E-7
F-7
E-7
F-7
E-7
4-107
C4423
C4424
C4425
C4426
C4427
C4428
C4429
C4430
C4431
C4432
C4433
C4434
C4435
C4436
C4437
C4438
C4439
C4902
C4905
C4906
C4907
C4908
C4909
C4910
C4911
C5711
C5712
E-7
F-7
E-7
E-7
E-8
F-8
F-8
F-8
F-8
E-8
F-8
F-8
F-8
E-8
G-6
G-6
F-6
C-8
D-7
D-7
E-7
E-8
E-8
D-8
D-8
A-2
A-3
CN1104
CN1106
CN1113
CN1114
CN1115
CN1116
CN1117
CN1120
CN1501
CN1551
CN3101
CN4401
CN4402
CN4403
CN4404
C-6
E-9
C-8
A-8
A-2
B-1
A-4
C-2
F-4
D-2
G-5
F-8
G-7
G-6
G-3
D1301
D1302
D1305
D1306
D1551
D1552
D1553
D2201
D2202
D4401
B-8
A-8
C-8
A-8
C-2
D-3
D-3
C-4
C-4
F-6
FB1504
FB1506
FB2202
FB2203
FB2204
FB2205
FB3601
FB3701
FB4901
F-4
F-3
F-6
D-4
C-4
F-6
C-4
C-3
C-8
IC1303
IC1502
IC1553
IC2001
IC2201
IC2202
IC3103
IC3603
IC3701
IC4401
IC4402
IC4901
IC4902
B-9
E-4
D-3
A-1
E-5
C-5
F-5
B-5
B-3
F-7
F-6
C-8
D-8
L1301
L1302
L1303
L1304
L1305
L1306
B-7
A-7
B-7
B-7
A-7
A-6
L1307
L1308
L1309
L1310
L1317
L1318
L1319
L1320
L1501
L1551
L1552
L2001
L2201
L2202
L2203
L2204
L2207
L2208
L2209
L3104
L3105
L3106
L3601
L3602
L3701
L3705
B-6
B-6
B-6
C-6
B-7
A-6
B-6
A-6
F-4
D-3
D-2
A-2
D-4
F-4
E-4
C-3
C-4
C-5
F-6
F-5
F-6
F-6
B-3
B-5
C-3
B-3
Q1104
Q1301
Q1314
Q1333
Q1551
Q1555
Q2207
Q3103
Q3104
Q3111
Q3116
Q3117
Q3118
Q3601
Q3602
Q3701
Q3702
Q3703
Q3704
Q3705
Q4401
Q4402
Q4901
Q5717
B-4
B-8
A-8
A-8
C-2
D-2
C-3
G-4
F-5
F-5
G-5
F-6
F-4
B-4
B-4
C-4
B-3
B-3
C-3
B-3
G-3
E-8
D-7
A-2
R1105
R1106
R1107
R1108
R1109
R1110
R1111
R1112
R1113
R1114
R1115
R1116
R1117
R1118
R1119
R1120
R1121
R1122
R1123
R1127
R1128
R1131
R1132
R1134
R1145
R1146
R1147
R1148
R1316
R1319
R1320
R1350
R1369
E-7
E-7
E-7
D-7
D-7
D-7
D-7
D-7
D-7
D-7
D-7
D-7
C-5
C-5
C-5
C-5
C-6
C-6
C-6
E-8
E-8
E-8
E-8
C-7
C-7
C-7
C-7
C-8
A-9
A-8
A-8
A-6
A-8
R1370
R1519
R1520
R1521
R1551
R1552
R1555
R1556
R1557
R1560
R2001
R2002
R2003
R2004
R2005
R2006
R2007
R2008
R2009
R2010
R2205
R2206
R2209
R2210
R2213
R2215
R2216
R2218
R2219
R2220
R2221
R2222
R2223
R2224
R2226
R2227
R2228
R2229
R2230
R2231
R2240
R2241
R2242
R2243
R2244
R2245
R2247
R2248
R2255
R2256
R3114
R3115
R3117
R3118
R3119
R3120
R3121
R3122
R3123
R3124
R3125
R3126
R3127
R3129
R3130
R3131
R3132
R3133
R3136
R3137
R3138
R3143
R3144
R3607
R3608
R3611
R3617
R3622
R3656
R3657
R3658
R3659
R3660
R3701
R3702
A-8
F-4
F-4
F-3
C-2
C-3
D-2
C-2
D-2
D-2
A-2
A-1
A-2
A-1
A-2
A-2
A-1
A-1
A-2
A-1
C-3
C-4
D-4
D-4
C-3
D-4
D-4
D-4
D-4
D-4
D-4
C-4
D-4
E-4
E-4
E-4
F-4
C-5
C-5
C-5
D-4
C-4
C-4
C-4
F-4
F-5
C-5
C-5
C-6
C-5
G-4
F-4
F-4
F-4
F-4
F-4
F-4
F-4
F-6
G-6
G-5
F-6
F-6
G-5
G-5
G-5
F-5
G-5
F-5
F-5
F-5
F-5
G-5
B-4
B-4
B-4
B-4
B-4
C-6
B-4
B-4
B-4
B-4
C-4
C-4
R3704
R3705
R3706
R3707
R3708
R3712
R3713
R3714
R3715
R3716
R3717
R3721
R3722
R3724
R3726
R3727
R3728
R3729
R3730
R4401
R4402
R4405
R4407
R4411
R4414
R4416
R4417
R4419
R4420
R4421
R4422
R4423
R4424
R4425
R4426
R4427
R4430
R4431
R4432
R4434
R4435
R4436
R4447
R4448
R4449
R4453
R4901
R4903
R4904
R4906
R4908
R4910
R4911
R4912
R4913
R4915
R4916
R4917
R4918
R4922
R4923
R4924
R4925
R4926
R4927
R4928
R4929
R4930
R4931
R4932
R4935
R4936
R4943
R4944
R5711
R5712
R5742
R5743
C-4
C-4
B-3
C-3
B-3
C-4
C-3
B-4
B-3
B-4
B-3
B-4
C-4
C-4
C-3
B-3
B-3
C-3
B-3
G-6
G-6
G-6
G-3
G-3
G-3
G-3
E-7
E-7
F-7
F-7
F-7
E-7
E-7
F-7
F-7
E-7
E-8
E-7
E-8
F-8
F-8
E-8
G-3
G-3
F-6
G-7
D-7
E-7
C-8
E-7
C-7
C-7
C-8
C-8
C-8
E-8
E-8
C-8
D-8
D-8
E-8
E-8
D-8
D-9
D-8
D-8
D-8
D-9
D-9
D-8
E-8
E-7
E-8
E-8
A-2
A-2
A-3
A-2
RB4402 G-5
RB4903 D-8
T1301
B-8
PARTS LOCATION
CD-292, CD-315, VC-254
VC-254 BOARD (SIDE B)

C1101
C1102
C1104
C1301
C1302
C1303
C1304
C1305
C1306
C1307
C1308
C1309
C1310
C1311
C1312
C1313
C1314
C1315
C1316
C1317
C1318
C1319
C1321
C1322
C1323
C1324
C1326
C1327
C1329
C1330
C1331
C1332
C1335
C1339
C1341
C1344
C1345
C1346
C1348
C1350
C1352
C1354
C1355
C1360
C1363
C1501
C1502
C1503
C1504
C1505
C1506
C1507
C1509
C1510
C1511
C1512
C1552
C1558
C1559
C1560
C1562
C1564
C1565
C1566
C1567
C1568
C1570
C1571
C1572
C2291
C2292
C2293
C3102
C3104
C3105
C3107
C3108
C3109
C3110
C3111
C3112
C3113
C3114
C3115
C3116
E-16
F-16
E-16
B-10
B-10
B-10
B-10
B-10
B-10
B-10
C-10
A-10
C-10
A-10
C-11
A-11
C-11
A-11
B-11
B-11
B-11
B-11
B-12
B-13
B-12
C-11
B-12
A-12
B-12
B-12
A-12
B-12
B-13
A-13
B-13
B-12
B-13
A-13
A-13
A-11
A-11
A-11
C-12
C-13
C-12
F-15
F-15
F-15
F-15
F-15
F-15
G-15
G-15
G-15
F-15
G-16
D-17
D-16
D-16
D-17
D-17
D-17
D-16
D-16
D-17
D-16
D-17
D-17
D-16
C-15
D-15
D-15
F-14
F-13
F-14
F-14
G-13
F-15
F-15
G-14
F-15
F-14
F-14
G-14
G-14
C3117
C3119
C3120
C3137
C3141
C3142
C3143
C3144
C3202
C3203
C3204
C3205
C3206
C3207
C3208
C3210
C3211
C3212
C3213
C3214
C3215
C3216
C3217
C3218
C3301
C3302
C3303
C3305
C3306
C3307
C3308
C3309
C3310
C3311
C3312
C3313
C3314
C3315
C3316
C3317
C3318
C3319
C3320
C3321
C3322
C3323
C3324
C3325
C3326
C3327
C3328
C3329
C3331
C3332
C3333
C3334
C3335
C3336
C3337
C3338
C3339
C3340
C3341
C3342
C3343
C3345
C3346
C3348
C3352
C3901
C3902
C3903
C3904
C3905
C3906
C3908
C3909
C3910
C3911
C3912
C3913
C3914
C3915
C3916
C3917
PARTS LOCATION
VC-254
G-14
G-14
G-14
G-14
G-14
G-14
G-14
G-14
F-13
F-12
F-13
F-13
F-13
F-13
F-13
F-13
F-13
F-13
F-13
F-13
F-13
F-12
F-13
F-12
C-15
C-12
D-15
E-13
C-14
D-13
D-13
D-15
D-13
E-15
E-13
E-13
E-12
E-15
E-15
E-13
E-13
E-13
F-13
E-13
E-13
E-14
E-15
D-15
D-15
E-15
F-14
D-10
C-10
C-11
C-11
C-12
C-10
C-10
C-11
C-11
E-14
E-14
E-15
E-15
E-15
E-15
E-13
E-13
E-15
A-17
A-17
A-17
A-17
A-17
A-17
A-17
A-17
B-17
B-17
B-18
B-17
B-18
A-18
A-18
B-18
C3918
C3919
C3920
C3921
C3922
C3923
C3924
C3925
C3926
C3927
C3928
C3934
C3935
C3936
C4440
C4441
C4442
C4501
C4504
C4505
C4506
C4507
C4508
C4509
C4510
C4801
C4802
C4803
C4804
C4805
C4806
C4807
C4808
C4810
C4811
C4812
C4813
C4814
C4815
C4816
C4817
C4819
C4820
C4821
C4822
C4823
C4824
C4825
C4827
C4903
C4904
C5701
C5702
C5703
C5704
C5705
C5706
C5707
C5708
C5709
C5710
C5713
C5714
C5715
C5716
C5717
C5718
C5719
C5720
C5721
C5722
C5723
C5724
C5725
C5728
C5730
C5731
C5732
C5733
C5734
C5735
C5736
C5737
C5738
C5739
B-18
A-18
A-18
B-18
A-18
B-18
A-18
A-18
A-18
A-18
A-18
A-17
B-18
B-18
G-13
G-13
G-13
F-11
E-12
E-12
E-12
E-12
E-12
F-11
E-11
C-15
A-14
B-15
A-15
A-15
A-14
A-14
A-15
A-15
A-15
A-15
A-14
A-14
A-14
A-14
A-14
C-14
B-13
B-13
C-13
B-13
B-13
B-13
B-13
F-12
F-12
A-16
A-16
B-17
A-16
A-16
A-17
A-16
A-16
B-17
B-16
B-17
A-16
B-17
A-16
B-17
B-16
A-17
B-15
B-16
B-17
B-15
B-17
B-16
B-15
B-16
B-15
B-17
B-16
B-17
B-16
C-16
B-17
C-16
C-17
C5740
C5741
C5742
C5743
C5744
C5745
C5746
C5747
C5748
C5749
C5750
C5751
C5752
C5753
C5754
C5755
C5756
C5757
C5758
C5759
C5806
C5807
C5808
C5809
C5810
C5812
C5813
C5814
C5815
C5816
C5817
C5818
C5819
C5820
C5821
C5822
C5823
C5824
C5825
C5826
C5827
C5829
C5830
C5832
C5833
C5835
C5836
C5838
C5839
C5840
C5841
C5842
C5843
C5844
C-16
C-16
C-16
C-16
C-16
C-16
C-16
C-16
C-16
C-16
C-17
C-17
C-17
C-17
C-17
C-17
C-17
C-17
B-15
B-16
C-18
C-18
C-17
C-17
C-18
C-18
C-18
C-17
C-17
C-17
C-18
C-18
C-17
C-18
C-18
C-18
C-17
C-18
C-17
C-18
C-17
C-17
C-18
B-18
B-18
B-17
B-17
B-18
B-18
B-18
B-18
C-18
C-18
C-17
CN1101 E-16
CN1108 E-10
D1101
D1102
D1103
D1105
D1106
D1501
D3301
D3302
D3303
D3304
D4802
D4803
D4804
D4806
E-16
E-16
E-16
F-16
E-16
G-16
E-12
E-12
E-15
E-15
A-14
C-13
B-15
A-14
FB1501
FB1502
FB1503
FB1505
FB2291
FB3303
FB3304
FB3307
FB4501
FB4801
FB4818
G-15
G-15
G-15
G-15
C-16
C-12
D-10
D-15
D-11
A-14
B-13
IC1301
IC1304
IC1501
IC1552
IC2291
IC3101
IC3102
IC3201
IC3202
IC3301
IC3302
IC3901
IC4501
IC4502
IC4801
IC4802
IC4803
IC4804
IC5701
IC5702
IC5801
B-11
B-13
F-15
D-17
D-16
F-14
F-15
F-13
F-12
D-14
C-12
A-18
E-11
D-12
A-13
A-15
B-14
A-14
B-16
C-17
C-18
L1312
L1313
L1314
L1315
L1316
L1553
L2291
L3102
L3103
L3201
L3303
L3304
L3305
L3306
L3307
L3901
L3902
L3903
L3904
L5701
L5803
A-13
B-13
B-13
A-13
B-13
D-17
D-15
G-13
G-14
F-12
E-13
E-15
E-13
E-15
C-10
B-17
B-18
B-18
B-18
C-16
B-18
Q1302
Q1303
Q1304
Q1305
Q1306
Q1307
Q1308
Q1309
Q1311
Q1312
Q1316
Q1321
Q1323
Q1324
Q1327
Q1328
Q1329
Q1330
Q1331
Q1332
Q1554
Q3102
Q3107
Q3109
Q3119
Q3120
Q3201
Q3305
Q3306
Q3309
Q3310
Q3311
Q3902
Q3903
Q4801
Q4802
Q4804
Q4806
Q4813
Q5708
Q5716
B-12
A-12
A-11
B-12
B-12
A-12
A-12
B-12
A-12
A-12
A-11
A-11
A-11
B-12
A-12
A-11
A-12
B-12
B-13
B-12
D-16
F-14
G-14
G-14
G-14
G-14
F-13
F-14
F-14
E-15
E-14
F-15
B-18
B-18
C-15
C-15
C-14
B-15
C-15
A-16
B-15
4-108
Q5718
A-16
R1144
R1149
R1150
R1151
R1152
R1153
R1154
R1155
R1301
R1302
R1303
R1304
R1305
R1306
R1307
R1309
R1310
R1311
R1312
R1313
R1314
R1317
R1318
R1321
R1322
R1323
R1326
R1327
R1330
R1331
R1332
R1333
R1334
R1335
R1336
R1337
R1338
R1339
R1340
R1341
R1342
R1343
R1345
R1346
R1347
R1348
R1349
R1355
R1356
R1357
R1358
R1359
R1360
R1361
R1362
R1363
R1364
R1365
R1366
R1367
R1368
R1501
R1502
R1503
R1504
R1505
R1506
R1508
R1509
R1512
R1523
R1561
R1562
R1563
R1564
R1565
R1566
R1567
R1568
R1570
R1571
R1572
R1573
D-10
A-16
A-16
E-16
E-16
E-16
E-16
E-16
B-10
B-10
B-10
C-11
C-10
A-10
B-10
C-10
A-10
A-10
C-11
A-11
C-11
A-12
A-12
A-12
A-12
A-11
C-11
A-12
A-11
A-11
A-11
A-11
A-11
C-12
A-11
C-12
A-11
A-11
A-11
B-12
B-12
C-12
A-11
A-11
A-12
A-12
A-13
B-12
B-12
C-11
C-11
C-10
A-10
B-13
C-13
C-13
C-12
C-12
B-12
C-13
C-13
F-15
F-15
F-15
G-15
G-15
G-15
G-15
F-15
G-16
G-15
D-16
D-16
D-16
D-16
D-17
D-16
D-16
D-17
D-17
D-17
D-17
D-16
R1574
R1575
R1576
R1577
R1596
R3103
R3104
R3107
R3108
R3109
R3110
R3111
R3113
R3128
R3139
R3140
R3141
R3142
R3205
R3206
R3210
R3212
R3213
R3214
R3215
R3307
R3309
R3310
R3311
R3312
R3313
R3315
R3316
R3317
R3318
R3319
R3320
R3321
R3322
R3323
R3324
R3325
R3326
R3327
R3328
R3329
R3330
R3331
R3332
R3333
R3334
R3335
R3335
R3336
R3337
R3338
R3339
R3340
R3341
R3343
R3345
R3346
R3347
R3348
R3349
R3350
R3351
R3352
R3353
R3354
R3356
R3357
R3358
R3359
R3360
R3361
R3362
R3363
R3364
R3365
R3366
R3367
R3368
R3369
R3370
D-16
D-16
D-16
D-16
D-16
F-13
F-13
G-14
G-14
G-14
G-14
G-14
G-14
G-15
G-14
G-14
G-14
G-14
F-13
F-13
F-12
F-13
F-12
F-13
F-13
D-13
E-13
E-12
E-12
E-13
E-13
E-14
E-14
E-15
E-15
E-15
E-13
E-14
E-13
E-15
E-15
D-15
E-15
E-15
F-14
F-15
D-11
E-14
F-15
D-10
F-14
C-10
F-15
F-14
C-11
F-15
D-10
E-14
F-14
F-14
D-10
C-10
C-10
C-10
C-10
C-10
E-15
C-12
C-10
C-10
E-15
C-10
E-15
C-12
E-15
C-11
C-11
C-11
C-11
C-11
C-11
C-11
C-11
C-11
C-11
R3371
R3372
R3375
R3376
R3385
R3386
R3387
R3388
R3389
R3390
R3391
R3392
R3393
R3394
R3395
R3396
R3397
R3398
R3903
R3904
R3905
R3908
R3909
R3911
R3912
R3913
R3916
R3917
R3918
R3919
R3920
R3921
R3922
R3923
R3924
R3936
R3939
R3940
R3941
R3942
R3943
R3948
R3949
R4408
R4409
R4410
R4428
R4429
R4450
R4451
R4452
R4502
R4503
R4507
R4508
R4511
R4512
R4515
R4520
R4521
R4522
R4523
R4524
R4526
R4527
R4530
R4801
R4802
R4803
R4804
R4805
R4806
R4807
R4808
R4809
R4810
R4811
R4812
R4813
R4814
R4815
R4816
R4817
R4818
R4819
C-11
C-11
C-13
C-14
E-13
C-14
F-15
F-15
F-14
F-14
F-14
E-15
F-15
F-15
E-15
E-14
E-14
E-14
B-17
A-17
A-17
B-17
A-17
A-18
B-17
B-18
B-18
A-18
A-18
A-18
A-18
A-18
A-18
B-18
A-18
B-18
B-18
B-17
B-17
A-17
A-17
B-18
B-18
G-12
G-12
G-12
G-12
G-12
G-13
G-13
G-13
E-12
E-12
F-12
E-10
E-10
E-12
E-12
D-12
D-11
D-11
D-11
D-11
D-11
D-12
E-12
C-15
C-15
C-14
A-14
A-14
C-15
C-15
A-14
C-15
C-15
C-14
A-15
A-15
A-15
A-15
A-14
A-14
A-15
A-15
R4820
R4821
R4822
R4823
R4824
R4829
R4830
R4832
R4833
R4834
R4835
R4836
R4840
R4855
R4861
R4862
R4863
R4864
R4867
R4868
R4869
R4872
R4873
R4876
R4878
R4882
R4883
R4884
R4885
R4886
R4887
R4888
R4896
R4897
R4898
R4899
R4902
R4905
R4920
R4921
R5707
R5708
R5709
R5710
R5714
R5715
R5717
R5718
R5719
R5720
R5721
R5724
R5725
R5728
R5730
R5731
R5732
R5733
R5744
R5745
R5746
R5747
R5801
R5802
R5803
R5805
R5806
R5807
R5809
R5814
R5815
R5816
R5817
R5818
R5819
R5820
R5821
R5822
R5823
R5824
R5825
R5826
R5827
R5828
R5829
B-15
B-15
B-15
B-15
A-15
B-15
B-15
C-15
A-14
A-14
A-14
A-14
C-14
C-15
A-14
A-14
C-14
C-14
A-14
A-14
A-14
C-14
C-14
C-13
B-13
B-13
B-13
B-13
B-13
B-13
B-13
B-13
B-15
B-13
B-13
B-13
F-12
F-12
D-11
D-11
A-16
A-16
A-17
A-17
A-17
A-17
B-15
B-15
B-15
B-17
B-17
C-16
C-16
C-16
C-16
C-17
C-17
C-17
B-15
B-15
B-15
B-15
C-17
C-18
C-18
C-18
C-17
C-18
C-18
C-17
C-18
C-17
C-18
C-17
C-18
C-18
C-17
C-17
C-18
C-18
C-17
B-17
B-18
C-17
B-18
VC-254 BOARD (SIDE B)
PC-082 BOARD (SIDE A)
PC-082 BOARD (SIDE B)
CF-079 BOARD (SIDE A)
R5830
R5831
R5834
R5846
R5847
B-17
B-17
B-18
B-18
C-18
E-2
D-11
B-15
B-15
B-15
B-13
C-14
A-14
X1501
X3301
X4801
X4802
X4901
G-16
D-12
C-14
C-13
F-12
C1164
C1165
C1167
C1168
C1169
C1180
C1181
C1186
C1187
C1188
C1189
C1191
C1192
C1193
C1195
C1200
C1902
C1903
C1907
C1909
C1910
C1911
C1912
C1914
C1915
C1967
C1969
C1972
C1973
C1974
BT101
RB4502
RB4801
RB4803
RB4804
RB4812
RB4814
RB4817
C1151
C1152
C1153
C1154
C1155
C1156
C1157
C1158
C1159
C1160
C1161
C1162
C1163
C1166
C1170
C1171
C1172
C1173
C1174
C1175
C1176
C1177
C1178
C1179
C1182
C1183
C1184
C1185
C1190
C1194
C1196
C1198
C1199
C1904
C1905
C1906
C1908
C1916
C1968
C1970
C1971
C101
C201
C202
C205
C206
C207
C208
C209
C210
C211
C212
C213
C214
C215
C216
C217
C218
C219
C220
C221
C223
C224
C226
C227
E-4
F-7
F-7
F-7
F-6
F-7
F-7
F-7
F-6
F-6
F-7
E-7
F-8
E-7
F-8
E-6
E-7
E-7
E-7
E-7
B-4
B-4
B-5
B-3
CN101
CN102
CN103
CN104
CN105
CN106
CN107
CN201
CN202
E-4
F-3
D-1
A-4
E-3
E-1
E-8
A-5
A-5
D101
D104
D108
D202
E-4
E-8
E-8
E-6
FB201
FB202
F-6
F-8
B-6
C-6
B-6
D-5
D-5
D-4
C-3
C-6
D-4
C-6
C-3
C-6
B-4
A-5
C-2
D-2
B-1
C-2
B-1
C-6
D-6
C-3
B-4
B-4
A-5
B-6
D-4
D-4
C-6
D-4
C-1
C-6
C-6
C-1
B-3
D-3
B-3
D-2
D-6
D-6
D-5
CN1152 B-6
CN1153 C-1
FB1151
FB1152
FB1155
FB1902
FB1903
C-2
C-1
D-4
B-3
C-1
IC1151
IC1152
IC1153
IC1154
IC1155
IC1160
IC1162
IC1902
B-6
D-6
C-2
B-2
B-5
D-5
D-6
D-3
L1151
C-6
Q1153
Q1156
Q1157
Q1158
Q1901
Q1902
Q1903
C-3
B-6
D-4
D-4
D-3
D-3
D-3
R1151
R1152
R1153
R1154
R1155
R1156
R1157
R1158
R1158
R1159
R1160
R1162
R1163
R1164
R1165
R1166
R1171
R1172
R1173
R1178
R1179
R1181
R1187
R1188
R1190
R1191
R1192
R1193
R1194
R1195
R1196
R1197
R1198
R1199
R1202
R1204
R1205
R1206
R1208
R1211
R1902
R1903
R1904
R1905
R1906
R1907
R1908
R1915
C-6
B-6
C-3
B-6
C-3
C-6
C-3
D-4
D-4
C-3
C-3
D-4
D-5
D-5
D-5
D-5
D-5
D-5
D-5
B-6
B-6
B-6
C-6
C-6
A-2
D-5
D-5
B-6
B-6
D-4
D-4
D-4
D-5
D-5
D-6
D-6
D-6
D-6
D-6
D-4
D-3
D-3
D-4
B-3
D-3
D-3
D-3
D-2
VDR111 C-6
VDR112 C-6
X1151
X1152
C-6
D-6
A-7
A-7
A-8
A-8
C-9
A-9
A-9
B-8
B-8
D-12
B-7
B-7
B-7
B-7
C-12
B-7
D-10
D-12
C-10
B-11
B-12
D-12
C-12
D-11
D-11
B-8
A-11
B-12
B-10
B-11
CN1901 C-9
D1151
D1152
D1901
D1902
C-12
C-12
E-7
D-12
FB1151
FB1153
FB1154
FB1156
FB1158
C-8
C-9
A-7
B-7
D-12
IC1156
IC1157
IC1158
IC1159
IC1161
IC1901
A-7
B-7
B-7
D-9
A-11
C-11
Q1154
Q1155
C-12
D-12
R1161
R1167
R1168
R1169
R1170
R1174
R1175
R1176
C-8
A-8
A-8
D-12
A-8
A-7
B-8
B-8
4-109
R1177
R1180
R1182
R1183
R1184
R1185
R1186
R1189
R1200
R1201
R1203
R1207
R1209
R1210
R1911
R1912
R1914
B-8
C-12
D-12
B-7
B-8
C-12
A-8
A-8
D-8
D-8
D-10
D-9
A-11
B-11
E-7
C-9
D-11
RB1151
RB1152
RB1154
RB1155
RB1156
C-8
C-8
A-9
A-9
B-8
IC201
IC202
IC203
F-7
F-6
B-4
L201
L202
F-6
E-6
Q101
Q102
Q201
F-1
F-1
F-6
R101
R103
R105
R106
R108
R112
R113
R130
R131
R203
R205
R206
R207
R208
R209
R210
R211
R212
R213
R214
R215
R216
R217
R218
R219
R220
R221
R222
R226
R227
R228
R229
R230
F-2
F-1
F-1
F-1
F-1
B-4
D-1
D-1
E-3
F-7
F-7
F-6
F-6
F-8
F-7
F-6
F-7
F-6
F-7
F-6
E-7
E-8
E-7
E-7
E-7
E-8
E-7
E-7
F-6
E-6
E-6
E-6
E-6
CF-079 BOARD (SIDE B)

D102
D103
D105
D106
D107
D109
D110
D111
D112
D113
D114
D115
D116
D117
D118
D119
D120
D121
D122
F-16
E-10
F-16
F-15
B-15
B-13
D-12
G-15
G-16
F-17
C-13
B-11
B-11
B-12
C-11
D-12
D-13
D-11
F-18
Q103
G-15
R102
R109
R110
R111
R114
R115
R116
R117
R118
R119
E-10
E-11
C-12
D-11
E-11
C-12
D-11
E-11
B-11
D-11
R120
R121
R122
R123
R124
R125
R126
R127
R128
R129
R231
R232
G-15
B-11
F-18
G-16
C-11
F-17
C-11
E-18
C-11
B-13
F-12
F-12
S101
S102
S103
S104
S105
S106
S107
S108
S109
S110
S111
S112
S113
S114
S115
S116
S117
S118
D-13
D-11
C-12
C-13
D-12
B-12
D-13
E-12
B-11
D-11
G-15
B-13
G-16
C-11
F-17
B-13
B-14
F-18
PARTS LOCATION
VC-254, PC-082, CF-079
CF-080 BOARD (SIDE A)

BT101
E-3
C101
C201
C202
C205
C206
C207
C208
C209
C210
C211
C212
C213
C214
C215
C216
C217
C218
C219
C220
C221
C223
C224
C226
C227
E-4
F-7
F-7
F-8
F-6
F-7
F-7
F-7
F-5
F-6
E-7
E-6
F-8
F-6
E-7
E-6
E-8
E-7
E-7
E-6
A-3
B-3
B-5
B-3
CN101
CN102
CN103
CN104
CN105
CN106
CN107
CN201
CN202
E-4
F-3
D-1
A-4
E-2
E-1
E-8
A-5
A-5
D104
D108
D202
E-8
E-8
E-6
FB201
FB202
F-5
F-7
IC201
IC202
IC203
F-7
F-6
B-3
L201
L202
F-6
F-6
Q101
Q102
Q201
F-1
F-1
F-6
R101
R103
R105
R106
R108
R112
R130
R203
R205
R206
R207
R208
R209
R210
R211
R212
R213
R214
R215
R216
R217
R218
R219
R220
R221
R222
R226
R227
R228
R229
R230
F-3
F-2
F-2
F-2
F-1
B-3
D-1
F-7
F-7
F-6
F-6
F-8
F-7
F-7
F-7
F-6
F-6
E-7
E-6
E-7
E-7
E-7
E-7
E-7
E-7
E-7
F-6
E-6
E-6
E-6
E-6
SI-028/029 BOARD
(SIDE A)
C301
C304
C305
C307
C308
C309
C310
C311
C312
B-2
B-3
B-3
A-2
A-3
A-3
A-3
B-3
B-3
D301
D302
D303
D304
D306
D307
D308
B-2
B-2
B-2
B-3
A-2
B-1
B-2
F301
B-3
C702
IC301
B-1
CN701 A-1
CN702 A-1
Q301
A-2
R307
R308
R309
R310
R312
R313
R314
R315
B-3
A-3
A-3
A-2
B-3
B-3
A-3
B-3
VDR301 B-2
VDR302 B-2
SI-028/029 BOARD
(SIDE B)
C306
B-7
CN301
CN302
CN303
CN304
B-6
B-6
B-6
B-7
D305
B-7
L301
B-6
R301
R311
A-6
B-6
SE301
SE302
A-5
B-5
LB-068/070 BOARD
(SIDE A)
LB-068/070 BOARD
(SIDE B)
D701
D702
A-4
B-4
IC701
A-4
Q701
Q702
A-4
A-4
R701
R702
R703
R704
R705
R706
A-4
A-4
A-4
A-4
B-4
B-4
TH701
A-4
CF-080 BOARD (SIDE B)

D101
D102
D103
D105
D106
D107
D109
D110
D111
D112
D113
D114
D115
D116
D117
D118
D119
D120
D121
D122
D-15
F-17
E-10
D-16
D-16
B-14
B-12
E-12
G-15
G-15
F-17
C-13
B-11
B-11
B-12
C-10
D-11
D-14
D-11
F-17
Q103
F-16
R102
R109
R110
R111
R113
R114
R115
R116
R117
R118
E-10
E-11
C-11
D-13
D-17
E-11
C-11
D-13
E-11
C-11
R119
R120
R121
R122
R123
R124
R125
R126
R127
R128
R129
R131
R231
R232
D-13
G-15
C-11
D-11
G-15
C-11
G-15
C-11
D-17
F-16
B-13
F-16
F-12
F-12
S101
S102
S103
S104
S105
S106
S107
S108
S109
S110
S111
S112
S113
S114
S115
S116
S117
S118
D-14
D-11
C-12
C-13
D-12
B-12
D-14
D-12
B-11
D-11
G-15
B-13
G-16
C-11
F-17
B-13
B-14
F-18
PARTS LOCATION
CF-080, SI-028, SI-029,LB-068, LB-070, PD-138
B-1
PD-138 BOARD (SIDE A)

C5501
C5503
C5504
C5505
C5506
C5507
C5508
C5509
C5510
C5511
C5512
C5513
C5514
C5515
C5516
C5517
C5518
C5519
C5520
C5521
C5522
C5523
C5524
C5527
C5528
C5529
C5530
C5531
C5532
C5602
C5603
C5604
C5605
C5606
C5607
C5704
A-6
A-5
C-5
B-5
B-5
B-5
C-5
A-4
A-5
B-4
B-4
A-4
A-4
B-5
B-5
A-4
A-4
A-4
B-5
A-3
A-3
D-4
B-3
A-5
A-5
C-6
D-5
C-6
A-3
D-4
D-4
D-3
B-2
B-2
D-1
B-1
CN5501
CN5502
CN5604
CN5701
CN5703
CN5704
CN5705
D-5
B-5
D-2
B-6
C-6
A-5
A-3
D5502
D5503
D5601
D5603
D5604
B-5
A-5
D-3
B-1
B-1
FB5502 B-6
FB5503 A-4
FB5504 A-4
4-110
IC5501
IC5502
IC5601
IC5602
IC5701
B-5
C-5
B-2
B-2
A-1
L5501
L5504
L5505
L5601
A-6
A-4
C-5
D-4
Q5501
Q5502
Q5509
Q5510
Q5511
Q5601
Q5602
Q5603
C-5
A-3
A-3
B-3
B-3
B-3
D-3
B-2
R5501
R5502
R5503
R5504
R5505
R5506
R5507
R5508
R5509
R5510
R5511
R5512
R5513
R5514
R5515
R5516
R5517
R5518
R5521
R5522
R5523
R5524
R5525
R5551
R5553
R5557
R5559
R5560
R5561
R5562
R5563
R5564
R5565
R5566
R5567
R5568
R5569
R5570
R5571
R5572
R5573
R5574
R5575
R5609
R5610
R5611
R5612
R5613
R5614
R5616
R5617
R5618
R5619
R5620
R5712
A-5
A-5
B-5
C-6
A-5
B-4
B-4
B-4
B-4
B-4
B-4
B-5
B-5
B-4
B-4
B-5
D-5
D-4
D-5
B-4
A-4
A-4
A-4
C-5
B-5
A-5
B-6
C-6
A-3
B-3
B-3
B-3
B-3
B-3
B-3
A-3
A-5
A-3
A-3
C-6
D-4
D-4
C-5
A-2
D-3
B-2
B-2
D-4
B-2
B-2
B-2
D-3
B-1
B-1
B-2
T5601
D-3
PD-139 BOARD (SIDE A)
FU-150/154 BOARD (SIDE A)
C5501
C5503
C5504
C5505
C5506
C5507
C5508
C5509
C5510
C5511
C5512
C5515
C5516
C5517
C5518
C5519
C5527
C5529
C5532
C5533
C5534
C5536
C5537
C5538
C5539
C5540
C5602
C5603
C5604
C5605
C5606
C5607
C5704
A-5
A-5
C-5
B-5
B-5
B-5
C-5
A-4
A-4
B-4
B-4
B-5
B-5
A-4
A-3
B-4
A-5
C-6
A-5
D-4
C-5
B-3
B-3
B-3
A-3
D-6
D-4
D-4
D-3
B-2
B-2
D-1
B-1
C401
C402
C403
C404
C405
C406
C407
CN5501
CN5502
CN5604
CN5701
CN5703
CN5704
CN5705
D-5
B-5
D-2
B-6
C-6
A-5
A-3
D5502
D5503
D5601
D5603
D5604
B-5
D-5
D-3
B-1
B-1
FB5502 B-6
FB5503 A-4
FB5504 A-4
IC5501
IC5502
IC5601
IC5602
IC5701
B-5
C-5
B-2
B-2
A-1
L5501
L5504
L5505
L5601
A-6
A-4
C-5
D-4
Q5501
Q5503
Q5504
C-5
B-3
A-3
Q5505
Q5506
Q5508
Q5602
Q5603
A-3
B-3
B-3
D-3
B-2
R5501
R5502
R5503
R5504
R5505
R5506
R5507
R5508
R5509
R5510
R5511
R5512
R5523
R5524
R5525
R5551
R5553
R5557
R5558
R5560
R5571
R5572
R5573
R5574
R5575
R5576
R5577
R5579
R5585
R5586
R5587
R5588
R5589
R5590
R5591
R5592
R5609
R5610
R5611
R5612
R5613
R5614
R5616
R5617
R5618
R5619
R5620
R5712
A-5
A-6
A-6
C-6
A-5
B-4
B-4
B-4
B-4
B-4
B-4
B-5
A-4
A-4
A-4
C-5
B-5
A-5
A-6
C-6
B-4
B-3
B-3
A-3
A-3
A-3
B-3
D-6
A-4
A-4
A-4
B-4
B-4
C-6
D-4
D-4
A-2
D-3
B-2
B-2
D-4
B-2
B-2
B-2
D-3
B-1
B-1
B-2
T5601
D-3
A-2
A-1
A-1
B-1
B-1
B-1
A-1
CN401 A-1
CN402 B-3
D401
D402
D408
B-1
B-1
A-3
F401
F402
F403
F404
A-1
B-1
B-1
B-1
L401
B-1
LF401
A-2
Q401
Q402
Q403
Q404
A-2
A-4
A-3
B-2
R401
R406
R407
R408
R409
R410
R429
R430
B-1
A-1
A-1
A-2
B-2
B-2
A-1
A-1
FU-150/154 BOARD (SIDE B)

C409
C410
A-5
B-5
CN403 B-6
D404
D405
D406
D407
A-4
B-4
A-4
A-4
F405
F406
B-5
B-5
Q405
Q407
Q408
Q409
Q410
Q411
Q412
B-5
A-5
A-5
B-5
B-5
B-5
B-5
R402
R403
R420
R421
R422
R423
R424
R425
R426
R427
R428
A-4
B-4
B-5
B-5
A-5
A-5
B-5
B-5
B-5
B-5
B-5
4-111E
PARTS LOCATION
PD-139, FU-150, FU-154
SECTION 5
ADJUSTMENTS
5-1
1.
Before starting adjustment
1-1.
Adjusting items when replacing main parts and boards.
When replacing main parts, adjust the items indicated by z in the following table.
Initialization of
B,C,D,E,F,7,8
page data
Camera
EVF
LCD
System control
Servo & RF
Video
IR
Audio
Mechanism
Initialization of C, D, 8 page data

Initialization of B page data *2
Initialization of E, F, 7 page data
HALL adj.
Flange back adj.
Optical axis adj.
Color reproduction adj.
AWB & LV standard data input
Auto white balance adj.
Angular velocity sensor sens. adj.
VCO adj.
RGB AMP adj.
Contrast adj.
COM DC adj. *5
VCO adj.
RGB AMP adj.
Black limit adj. *4
Contrast adj.
Center level adj. *4
COM-AMP adj. *3, PSIG gray adj. *4
V-COM adj.
White balance adj.
Serial No. input
REEL FG adj.
Switching position adj.
AGC center level adj.
APC & AEQ adj.
PLL fo & LPF fo adj.
Hi8/Std8 switching position adj.
CAP FG offset adj.
27MHz origin oscillation adj.
Chroma BPF fo adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Hi8/Std8 Y/C level setting
Hi8/Std8 AFC fo adj.
IR video carrier frequency adj.
IR video deviation adj.
IR audio deviation adj.
Hi8/Std8 AFM BPF fo adj.
Hi8/Std8 AFM 1.5MHz deviation adj.
Tape path adj.
IC2291 (EVR)
IC3901 (IR transmitter)
IC5701 (AUDIO IN/OUT, AFM)
VC-254 board
VC-254 board
VC-254 board
IC3701 (LINE IN/OUT)

VC-254 board
IC3301 (DV signal process)
IC3101 (EQ, A/D conv. PLL)

VC-254 board
VC-254 board
IC2201 (Camera, Hi8/Std8 process)
IC3103 (REC/PB AMP)

VC-254 board
IC1502 (S/H, AGC)
VC-254 board
VC-254 board
z
z
z
z
z
VC-254 board
SE301,302 (PITCH,YAW sensor)
IC1501, X1501 (Timing generator)
SI-028/029 board
PD-138/139 board IC5502 (Timing generator (LCD))
(Timing generator (EVF))

CF-079/080 board IC202
PD-138/139 board Q5602, T5601 (Inverter)
(LCD driver (EVF))

CF-079/080 board IC201
LS chassis assy
(CCD imager)
Mechanism deck
z
z
z
CD-292/315 board IC501
M901
M902
Mechanism deck
Mechanism deck
*1
Mechanism deck
(Drum assy.) *1
LCD901 (LCD panel)
(Capstan motor)
ND901 (Fluorescent tube)
LCD block
Lens device
Adjustment
LCD block
Adjustment
Section
PD-138/139 board IC5501 (RGB driver (LCD))
Replaced parts
Parts replacement
Block replacement
z
z
z
z
z z
z
z
z
z
z z
z
z
z
z
z
z
z
z
z
z z
z
z z
z
z z
z z
z z
z z
z
z
z
z
z
z
z z
z z
z
z
z
z z z z
Table. 5-1-1(1).
5-2
z
z z
z z
z z z
z
z
z
z
z
z
Initialization of
B,C,D,E,F,7,8
page data
Camera
EVF
LCD
System control
Servo & RF
Video
IR
Audio
Mechanism
Initialization of C, D, 8 page data

Initialization of B page data *2
Initialization of E, F, 7 page data
HALL adj.
Flange back adj.
Optical axis adj.
AWB & LV standard data input
Angular velocity sensor sens. adj.
VCO adj.
RGB AMP adj.
Contrast adj.
COM DC adj. *5
VCO adj.
RGB AMP adj.
Black limit adj. *4
Contrast adj.
Center level adj. *4
COM-AMP adj. *3, PSIG gray adj. *4
V-COM adj.
White balance adj.
Serial No. input
REEL FG adj.
APC & AEQ adj.
PLL fo & LPF fo adj.
CAP FG offset adj.
27MHz origin oscillation adj.
Chroma BPF fo adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Hi8/Std8 Y/C level setting
IR video carrier frequency adj.
Hi8/Std8 AFM BPF fo adj.
Tape path adj.
IC4901 (EEPROM)
VC-254 board
IC1154 (FLASH MEMORY) *2
IC4502 (EEPROM)
(COMPLETE)
z
z
VC-254 board
PC-082 board
VC-254 board
(COMPLETE) *2
(COMPLETE)
PD-138/139 board (COMPLETE)
PC-082 board
Adjustment
SI-028/029 board
Adjustment
Section
CF-079/080 board (COMPLETE)
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
*1: When replacing the drum assy or mechanism
Board
EEPROM
deck, reset the data of page: 2, address: A2 to A4
replacement replacement
to 00. (Refer to Record of Use check of 54. SERVICE MODE)
*2: DCR-TRV330/TRV530
*4: DCR-TRV530
*5: CF-079 board (Part No. suffix: 12 or later)
CF-080 board (Part No. suffix: 13 or later)
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
Table. 5-1-1(2).
5-3
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
Note: CD-292 board: DCR-TRV230/TRV330

CD-315 board: DCR-TRV530
CF-079 board: DCR-TRV230/TRV330
CF-080 board: DCR-TRV530
PD-138 board: DCR-TRV230/TRV330
PD-139 board: DCR-TRV530
SI-028 board: DCR-TRV230/TRV330
SI-029 board: DCR-TRV530
5-1. CAMERA SECTION ADJUSTMENT

1-1.
PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)
1-1-1. List of Service Tools

Oscilloscope
Color monitor
Regulated power supply
Digital voltmeter
Ref. No.
Vectorscope
Name
Parts Code
Usage
ND filter 1.0
J-6080-808-A
Auto white balance adjustment/check

White balance adjustment/check
White balance check
J-2
ND filter 0.4
ND filter 0.1
J-6080-806-A
J-6080-807-A
White balance check

White balance check
J-3
J-4
Pattern box PTB-450

Color chart for pattern box
J-6082-200-A
J-6020-250-A
J-1
Filter for color temperature correction (C14)
J-6080-058-A
J-6
Adjustment remote commander

(RM-95 upgraded) (Note1)
Siemens star chart
J-6080-875-A
For checking the flange back
J-7
J-8
Clear chart for pattern box

Multi CPC jig
J-6080-621-A
J-6082-311-A
For adjusting the LCD block
J-9
CPC-13 jig
J-6082-443-A
J-10
Power code (Note2)
J-6082-223-A
J-11
Extension cable (100P 0.5mm)
J-6082-352-A
J-12
IR receiver jig
J-6082-383-A
For extension between the PC-082 board (CN1901) and

the VC-254 board (CN1104)
For adjusting the IR transmitter
J-13
J-14
Minipattern box
Camera base
J-6082-353-B
J-6082-384-A
For adjusting the flange back

For adjusting the flange back
J-5
J-6082-053-B
Note1: If the micro processor IC in the adjustment remote commander is

not the new micro processor (UPD7503G-C56-12), the pages
cannot be switched. In this case, replace with the new micro
processor (8-759-148-35).
For adjusting the video section

For adjusting the color viewfinder
For connecting the battery terminal and DC power supply
Note2: Connect the adjustment remote commander to the LANC jack,

and set to HOLD switch to the ADJ side.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
J-12
J-13
J-14
Fig. 5-1-1.
5-4
1-1-2.
Preparations
Note1: For details of how remove the cabinet and boards, refer to 2.
DISASSEMBLY.
Note2: When performing only the adjustments, the lens block and boards
need not be disassembled.
1)
2)
Pattern box
Connect the equipment for adjustments according to Fig. 5-1-3.

The front panel block (SI-028/029 board, focus ring, microphone
unit) must be assembled because the focus ring is used for
adjustments.
1.5 m
Note3: As removing the cabinet (R) (removing the VC-254 board CN1117)
means removing the lithium 3V power supply (CF-079/080 board
BT101), data such as date, time, user-set menus will be lost. After
completing adjustments, reset these data. If the cabinet (R) has
been removed, the self-diagnosis data, data on history of use (total
drum rotation time etc. ) will be lost. Before removing, note down
the self-diagnosis data (data of page: 2, address: B0 to C6) and
data on history use (data of page: 2, address: A2 to AA). (Refer to
5-4. Service Mode for the self-diagnosis data and data on the
history use.)
Front of the lens
Note4: Setting the Forced Camera Power ON Mode

1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button.
The above procedure will enable the camera power to be turned
on with the SS-1380 block removed. After completing adjustments,
be sure to exit the Forced Camera Power ON Mode.
Fig. 5-1-2.
Note5: Exiting the Forced Camera Power ON Mode

button.
5-5
Cabinet (R)
CN5704
Multi CPC jig

(J-6082-311-A)
Must be connected when

performing the LCD
system adjustments.
CN5705
CN5502
LCD
window
CN5703
PD-138/139
board
CN5501
CPC-13 jig
(J-6082-433-A)
CN5604
To CF-079/080 board
CN102
To PD-138/139
board CN5701
Must be connected.
CN4404
Front panel block
CN4403
CN3101
CN1501
Lens block
CN4402
CN4401
VC-254
board
CN1108
CN1113
Must be connected when

performing the video
system or EVF system
adjustments.
CN1551
Must be connected.
CN1104
CN1120
CN1116
FU-150/154 board
CN401
DC IN jack
CN1117
SI-028/029 board
CN304
LANC jack
AUDIO/VIDEO Extension cable

jack
(J-6082-352-A)
CN1152
Vector scope
AC power adaptor
(8.4Vdc)
AC-L10,
AC-VQ800 etc.
CN1901
Color monitor
VIDEO
(Yellow)
PC-082
board
CN1153
Terminated
at 75
DCR-TRV330/TRV530
AUDIO L
(White)
AUDIO R
(Red)
Fig. 5-1-3.
5-6
Adjustment remote
commander (RM-95)
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
1.
2.
3.
4.
5.
6.
7.
POWER switch (SS-1380 block) ........................... CAMERA

NIGHT SHOT switch (Lens block) ................................. OFF
DEMO MODE (Menu display) ....................................... OFF
DIGITAL ZOOM (Menu display) ................................... OFF
STEADY SHOT (Menu display) ..................................... OFF
DISPLAY (Menu display) ................................. V-OUT/LCD
DISPLAY (CF-079/080 board) ......................................... ON
8.
9.
10.
11.
12.
13.
14.
FOCUS switch (FP-282 flexible) .......................... MANUAL

BACK LIGHT (CF-079/080 board) ................................. OFF
PROGRAM AE (Menu display) ...................................... OFF
PICTURE EFFECT (Menu display) ................................ OFF
DIGITAL EFFECT (Menu display) ................................. OFF
AUTO SHUTTER (Menu display) .................................. OFF
16 : 9 WIDE (MENU display) ......................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Color bar chart (Color reproduction adjustment frame)
Electronic beam scanning frame
A B
A=B
C=D
Yellow
Cyan
Green
White
Magenta
Red
Blue
Blue
Yellow
Cyan
Green
White
Magenta
Red
CRT picture frame
B A
Fig. b (monitor TV picture)
Enlargement
Fig. a
(VIDEO terminal
output waveform)
Difference in level
Adjust the camera zoom and direction to

obtain the output waveform shown in Fig. a
and the monitor TV display shown in Fig. b.
Fig.5-1-4.
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
2) Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3) Flange back adjustment chart
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
841mm) black and white vellum paper.
White
841mm
Black
1189mm
Fig. 5-1-5.
Note: Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
5-7
1-2.
INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE
DATA
1-2-1.
Processing after Completing Modification of C, D, 8 Page data

Order Page Address Data
Procedure
1
2
INITIALIZATION OF C, D, 8 PAGE DATA
2
2
00
01
1. Initializing the C, D, 8 Page Data
Adjusting Address
Adjusting page
10 to FF
D
Adjusting Address
Adjusting page
10 to FF
8
Adjusting Address
00 to FF
Initializing Method:
01
81
01
10
Set the data

Set the data
80
0A
Set the data, and press the

PAUSE button.
80
Note: Fixed data-1: Initialized data. (Refer to 1. Initializing the C, D, 8

Page Data.)
Fixed data-2: Modified data. (Refer to 2. Modification of C, D, 8
Page Data.)
00 to 0F
10
11
12
13
14 to 16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23 to 24
25
26
27
28
29
2A to 2B
2C
2D to 2F
30
31 to 42
43
44 to 48
49
4A to 9A
9B
9C
9D
9E
9F to A4
Procedure
0
3
3. C Page Table
Address
1
2
Check that the data changes to

1A
Perform Modification of C, D,
8 Page Data.
2. Modification of C, D, 8 Page Data

If the C, D, 8 page data has been initialized, change the data of the
Fixed data-2 address shown in the following tables by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3)
4)
Set the data

Set the data, and press the
PAUSE button.
Note: If the following symptoms occur after completing of the

Modification of C, D, 8 page data, check that the data of the Fixed
data-2 addresses of D page are same as those of the same model of
the same destination.
1) The battery end mark on the LCD screen is flashing.
2) The power is shut off so that unit cannot operate.
Note1: If Initializing the C, D, 8 Page Data is performed, all data of the

C page, D page and 8 page will be initialized. (It is impossible to
initialize a single page.)
Note2: If the C, D, 8 page data has been initialized, the following
adjustments need to be performed again.
1) Modification of C, D, 8 page data
2) Serial No. input
3) Viewfinder system adjustments
4) LCD system adjustments
5) Servo and RF system adjustments
6) Video system adjustments
Adjusting page
29
29
When changing the data, press the PAUSE button of the

adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
5-8
Initial value
EE
00
00
00
E0
25
25
25
25
25
3E
3E
CA
99
88
E3
A1
04
20
03
E0
Remark
Fixed data-1
REEL FG adj.
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
PLL fo adj.
APC adj.
LPF fo adj.
Fixed data-1
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Chroma BPF fo adj.
PLL fo fine adj.
Fixed data-1
APC adj.
Fixed data-1
REEL FG adj.
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
C page
Address
A5
A6
A7
A8
A9 to AE
AF
B0
B1 to B6
B7
B8 to D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0 to E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0 to F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Initial value
4. D Page Table
Remark

Page Data.)
Page Data.)
Fixed data-2
Fixed data-1
Fixed data-2
Address
Fixed data-1
Fixed data-2
00 to 0F
10
11 to 12
13
14 to 1D
1E
1F
20 to 26
27
28
29
2A to 2C
2D
2E to 2F
30
31
32
33
34 to 47
48
49
4A to 4D
4E
4F
50
51
52
53
54
55 to 57
58
59
5A
5B
5C
5D to 64
65
66
67
68
69 to 6A
6B
6C to 8F
90
91
92
93
94
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
08
00
46
01
02
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
Fixed data-1
Fixed data-2
Fixed data-1
Serial No. input
Fixed data-1
Emergency memory address
Table. 5-1-2.
95
96 to 98
5-9
Initial value
00
Remark
Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
87
6F
27
97
VCO adj. (EVF)

Fixed data (*1)
COM DC adj. (*2)
RGB AMP adj.(EVF)
Fixed data-1
D page
Address
99
9A to 9F
A0
A1
A2
A3
A4
A5
A6
Initial value
37
Contrast adj. (EVF)
Fixed data-1
Fixed data-2

Page Data.)
Page Data.)
Address
80
70
80/26
2B/B3
00/09
A7
B5/41
A8
A9
AA
AB
80
80
3E/1A
00/4A
AC
AD
AE
AF
B0 to FF
5. 8 Page Table
Remark
Remark
VCO adj. (LCD)

00 to 3F
40
41 to 78
79
7A to FF
V-COM adj. (LCD)

RGB AMP adj.(LCD)
Fixed data (TRV230,TRV330)
Black limit adj. (LCD) (TRV530)
COM AMP adj. (LCD)
(TRV230,TRV330)
PSIG gray adj. (LCD) (TRV530)
White balance adj. (LCD)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Table. 5-1-4.
Contrast adj. (LCD)

Center levei adj. (LCD) (TRV530)
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Note: XX / YY
XX : DCR-TRV230/TRV330
YY : DCR-TRV530
*1 : CF-079 board (Part No. suffix: 11)

CF-080 board (Part No. suffix: 11 or 12)
*2 : CF-079 board (Part No. suffix: 12 or later)
Table. 5-1-3.
5-10
1-2-2.
2. Modification of B Page Data

If the B page data has been initialized, change the data of the Fixed
data-2 address shown in the following tables by manual input.
INITIALIZATION OF B PAGE DATA

(DCR-TRV330/ TRV530)
Note: When reading the B page data, insert a Memory Stick into the
Memory Stick slot.
Preparations:
Switch setting:
POWER ................................................................. MEMORY
1. Initializing the B Page Data
Note: If the B page data has been initialized, the following adjustments
need to be performed again.
1) Modification of B page data
Adjusting page
Adjusting Address
00 to FF
0
2
01
8F
01
03
Set the data.

Set the data, and press PAUSE
button.
8F
00

button.
button.
0E
00
01
F3
00
01
0E
8F
03
8F
00

button.
button.
Modifying Method:
data: 01.
not operate.
Procedure
1
2
Procedure
3)
When changing the data, dont press the PAUSE

button.
Processing after Completing Modification of B Page data:

Procedure
1
5
0E
00 Set the data, and press PAUSE
button.

button.
button.
01.
Perform Modification of B
Page Data.
01
FB
00
01
0E
5
6
2
2
00
01
29
29

button.
button.
Check that the data changes to 01.
(The change data are written in the
flash memory.)
Set the data.
button.
3. B Page Table
Note: Fixed data-1: Initialized data. (Refer to 1. Initializing the B Page
Data.)
Fixed data-2: Modified data. (Refer to 2. Modification of B Page
Data.)
Address
00 to FF
Remark
Fixed data-1
(Initialized data)
Table. 5-1-5.
5-11
1-2-3.
3. F Page Table
INITIALIZATION OF E, F, 7 PAGE DATA
Note: Fixed data-1: Initialized data. (Refer to 1. Initializing the E, F, 7

Page Data.)
Fixed data-2: Modified data. (Refer to 2. Modification of E, F, 7
Page Data.)
1. Initializing the E, F, 7 Page Data

Note1: If Initializing the E, F, 7 Page Data is performed, all data of the
E page, F page and 7 page will be initialized. (It is impossible to
initialize a single page.)
Note2: If the E, F, 7 page data has been initialized, following adjustments
need to be performed again.
1) Modification of E, F, 7 page data
2) Camera system adjustments
3) Servo and RF system adjustments
4) Video system adjustments
5) IR transmitter adjustments
6) Audio system adjustments
Adjusting page
Adjusting Address
Adjusting page
10 to FF
E
Adjusting Address
Adjusting page
00 to FF
7
Adjusting Address
00 to FF
00 to 0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D to 22
23
24
25
26
27 to 2D
2E
2F to 32
33
34 to 37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44 to 46
47
48
49
4A to 4C
4D
4E
4F
50
51
52
53
54
55
56
Procedure
1
2
0
6
01
00
01
55
Set the data.

Set the data.
01
55
02

button.
01.
Perform Modification of E, F, 7
Page Data.
Address
2. Modification of E, F, 7 Page Data

If the E, F, 7 page data has been initialized, change the data of the
Fixed data-2 address shown in the following table by manual input.
Modifying Method:
data: 01.
not operate.
3)
When changing the data, press the PAUSE button of the

adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
4)
Processing after Completing Modification of E, F, 7 Page data

Procedure
1
2
00
29 Set the data
2
01
29
Set the data, and press the PAUSE

button.
5-12
Initial value
00
00
00
00
00
00
00
00
00
00
00
00
Remark
Emergency memory address
Fixed data-2
Fixed data-1
Fixed data-2
the same model.)
4A
70
8A
80
7A
2B
80
65
80
8D
87
33
34
8C
2A
18
37
0D
13
08
6E
00
19
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
HALL adj.
Fixed data-2
Auto white balance & LV standard
data Input

Fixed data-1
Fixed data-1
Fixed data-1
27MHz origin osc. adj.
Flange back Adj.
F page
Address
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69 to 7A
7B
7C
7D
7E
7F
80
81 to 8D
8E
8F
90 to 98
99
9A to 9F
A0
A1 to AB
AC
AD
AE
AF
B0
B1
B2
B3 to CC
CD
CE to D6
D7
D8
D9 to DC
DD
DE
DF
E0 to EA
EB
EC
ED to F2
F3
F4 to F5
F6
Initial value
00
19
00
00
04
00
00
6D
67
00
00
0A
00
83
50
69
64
A6
94
80
41
33
C7
Address
Remark
Flange back Adj.
F7 to FF
Remark
Fixed data-1
Table. 5-1-6.
Angular velocity sensor sensitivity

adj.
Optical axis adj.
Flange back Adj.
CAP FG offset adj.
Fixed data-1
Hi8/Std8 Y output level setting
Hi8/Std8 chroma output level setting
Fixed data-1
Hi8/Std8 1.5MHz deviation adj.
Hi8/Std8 1.7MHz deviation adj.
Hi8/Std8 AFM BPF adj.
IR video carrier freq. adj.
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
the same model.)
FD
F4
Initial value
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
5-13
4. E Page Table
5. 7 Page Table

Page Data.)
Page Data.)

Page Data.)
Page Data.)
Address
Address
00 to 04
05
06
07 to 0E
0F
10
11
12
13
14 to 17
18
19 to 1B
1C
1D
1E to 2F
30
31 to 33
34
35
36
37
38
39
3A to 42
43
44
45
46 to 50
51
52
53
54
55
56 to 58
59
5A to 5C
5D
5E
5F
60 to 6B
6C
6D to 71
72
73 to 7D
7E
7F to 8B
8C
8D
8E
8F to FF
Remark
Fixed data-1
Fixed data-2
00 to A7
A8
A9
AA
AB
AC to AE
AF
B0 to CF
D0
D1
D2 to FF
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Remark
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Table. 5-1-8.
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
the same model.)
Fixed data-1
Table. 5-1-7.
5-14
1-3.
CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the

specified values of VIDEO SYSTEM ADJUSTMENTS are
satisfied.
1. HALL Adjustment
For detecting the position of the lens iris, adjust AMP gain and
offset.
Subject
Not required
Measurement Point
Measuring Instrument
Display data of page 1 (Note1)

Adjustment Page
Adjustment Address
F
38, 39, 3A
Specified Value 1
Specified Value 2
86 to 8A
14 to 18
Note1: Displayed data of page 1 of the adjustment remote commander.

1 : 00 : XX
IRIS display data
Switch setting:
POWER .................................................................. CAMERA
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
3
4
6
6
6
94
95
01
02
01
88
16
6D
00
Set the data.

Set the data.
button.
01. (Note2)
button.
Note2: The adjustment data will be automatically input to page: F, address:

38, 39, 3A.
Checking method:
Procedure
1
0
03
03 Set the data.
2
01
01

button.
Check that the IRIS display data
(Note1) satisfies the specified
value 1.
01
03

button.
Check that the IRIS display data
(Note1) satisfies the specified
value.2.
Processing after Completing Adjustments:

Procedure
1
6
94
00 Set the data.
2
3
6
6
95
01
00
00
Set the data.

button.
4
5
0
0
03
01
00
00
Set the data.

Set the data.
5-15
2. Flange Back Adjustment

(Using Minipattern Box)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
Subject
Siemens star chart with ND filter for
the minipattern box (Note1)
Adjustment Page

F
Adjustment Address
4E to 5D, 61
Note1: Dark Siemens star chart.

Note2: Check that the data of page: 6, address: 02 is 00. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Preparations:
1) The minipattern box is installed as shown in the following
figure.
Adjusting method:
Procedure
1
0
01
01 Set the data.
Note: The attachment lenses are not used.
2)
3)
4)
5)
Install the minipattern box so that the distance between it and

the front of the lens of the camcorder is less than 3cm.
Make the height of the minipattern box and the camcorder equal.
Check that the output voltage of the regulated power supply is
the specified voltage.
Check that at both the zoom lens TELE end and WIDE end,
the center of the Siemens star chart and center of the exposure
screen coincide.
6
6
82
01
01
13
Set the data.

button.
01
27
02

button.
01. (Note3)

4E to 5D, 61.
Specified voltage: The specified voltage varies according to the

minipattern box, so adjust the power supply
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.

Procedure
1
6
82
00 Set the data.
Below 3 cm
2
3
Minipattern box
Camcorder
Camera
table
Regulated power supply
Output voltage : Specified voltage 0.01Vdc
Output current : more than 3.5A
Red (+)
Black ()
Yellow (SENS +)
White (SENS )
2
3
Need not connected
Black (GND)
Fig. 5-1-6.
5-16
01
00
Set the data.

Turn off the power and turn on
again.
Perform Flange Back Check.
3. Flange Back Adjustment

(Using Flange Back Adjustment Chart and Subject
More Than 500m Away)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
3-2. Flange Back Adjustment (2)
Perform this adjustment after performing Flange Back Adjustment
(1).
Subject
Subject more than 500m away
(Subjects with clear contrast such as
buildings, etc.)
3-1. Flange Back Adjustment (1)

Subject
Flange back adjustment chart
(2.0 m from the front of the protection
glass)(Luminance: 350 50 lux)
Adjustment Page

F
Adjustment Address
4E to 5D, 61
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Adjusting method:
0
6
01
82
01
01
Set the data.

Set the data.
01
13
01
15
02

button.
button.
01. (Note2)
Check operation on TV monitor
Adjustment Page
Adjustment Address
F
4E to 5D, 61
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Procedure
1
2
Measurement Point
Preparations:
1) Set the zoom lens to the TELE end and expose a subject that is
more than 500m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500m away should
not be in the screen.)
Adjusting method:
Procedure
1
0
01
01 Set the data.

4E to 5D, 61.
2
3
6
6
82
01
01
13

4

Procedure
1
again.
2
Perform Flange Back

Adjustment (2)
01
02
29
Set the data.

button.
Place a ND filter on the lens so
that the optimum image is obtain.
button.
01.(Note2)

4E to 5D, 61.

Procedure
1
2
3
4
5-17
6
0
82
01
00
00
Set the data.

Set the data.
again.
Perform Flange Back Check.
4. Flange Back Check

Subject
Siemens star
(2.0m from the front of the lens)
(Luminance : approx. 200 lux)
Measurement Point
Check operation on TV monitor
Specified Value
Focused at the TELE end and WIDE end.
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Note: When the auto focus is ON, the lens can be checked if it is focused
or not by observing the data on the page 1 of the adjustment remote
commander.
1) Select page: 0, address: 03, and set data: 0F.
2) Page 1 shows the state of the focus.
1 : 00 : XX
Odd: Focused
Even: Unfocused
Checking method:
3) Place the Siemens star 2.0m from the front of the lens.
4) To open the IRIS, decrease the luminous intensity to the
Siemens star up to a point before noise appear on the image.
5) Shoot the Siemens star with the zoom TELE end.
6) Turn on the auto focus.
7) Check that the lens is focused (Note).
9) Shoot the Siemens star with the zoom WIDE end.
10) Observe the TV monitor and check that the lens is focused.
5-18
5. Optical Axis Adjustment

Align the lens Optical Axis with that of the CCD imager. If deviated,
center of picture can lose focus when zoom is operated from the
WIDE end to the TELE end.
Subject
Siemens star
Measurement Point
Check on the monitor TV
Adjustment Page
Adjustment Address
F
60
Note: This adjustment should be carried out upon completion of Flange

back adjustment.
Switch setting:
1) POWER .................................................................. CAMERA
2) DIGITAL ZOOM (Menu display) ................................... OFF
3) STEADY SHOT (Menu display) ..................................... OFF
Area
Display phase
1
2
3
4
5
6
7
8
22.6 to 67.5
67.6 to 112.5
112.6 to 157.5
157.6 to 202.5
202.6 to 247.5
247.6 to 292.5
292.6 to 337.5
337.6 to 22.5
Correction data
(Page: F, address: 60)
01
02
03
04
05
06
07
08
Table 5-1-9.
Preparations before adjustments:

1) Playback the monoscope segment of the system check tape
(WR5-5ND).
2) Attach the optical axis frame chart (transparent) on the monitor
TV screen. Center of monoscope image and that that of optical
axis frame must be agree.
3) Set to the camera mode.
Adjusting method:
2) Select page: F, address: 60, set data: 00, and press the PAUSE
button.
3) Place the Siemens star 2.0 m away from the front of the lens.
5) Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.
7) Measure on the monitor TV screen in which area of the optical
axis frame the center of the Siemens star is located. Measure
the amount of displacement (distance between the center of
the Siemens star and the center of the optical axis frame.) The
measurement value is named L1.
8) Read the correction data corresponding to the area from Table
5-1-9.
9) Input the correction data to page: F, address: 60, and press the
PAUSE button
11) Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.
13) Measure the amount of displacement (distance between the
center of the Siemens star and the center of the optical axis
frame.) The measurement value is named L2.
14) Compare the values L1 and L2, and confirm that L2 is smaller
than L1. If L2 is lager than L1, select page: F, address: 60, set
data: 00, and press the PAUSE button.
Fig. 5-1-7.
5-19
6. Picture Frame Setting

Subject
Color bar chart
(Color reproduction adjustment frame)
(1.5m from the front of the lens)
Measurement Point
Video output terminal

Oscilloscope and TV monitor
Specified Value
A=B, C=D, E=F
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Setting method:
2) Adjust the zoom and the camera direction, and set to the
specified position.
3) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in following
adjustments using Color reproduction adjustment frame.
Check on the oscilloscope

1. Horizontal period
A=B
C=D
Processing after Completing Camera System Adjustments:

After completing the camera system adjustments, release the data
settings.
Fig. 5-1-8.
2. Vertical period
E=F
Fig. 5-1-9.
Check on the monitor TV (Underscanned mode)
Color bar chart picture frame
Fig. 5-1-10.
5-20
Monitor TV picture frame
7. Color Reproduction Adjustment

Adjust the color Separation matrix coefficient so that proper color
reproduction is produced.
Subject
Color bar chart
Measurement Point

Vectorscope
Adjustment Page
Adjustment Address
F
47, 49, D7, D8
Specified Value
All color luminance points should settle

within each color reproduction frame.
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Adjusting method:
3) Select page: F, address: 8B, and write down the data.
4) Select page: F, address: 8B, set data: 2E, and press the PAUSE
button.
5) Select page: F, address: 2B, set data: 17, and press the PAUSE
button.
6) Select page: 6, address: 01, set data: 3D, and press the PAUSE
button.
7) Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
8) Change the data of page: F, address: 47, 49, D7 and D8, settle
each color luminance point in each color reproduction frame.
Note: Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data
will not be written to the memory.
Burst position
Fig. 5-1-11.

1) Select page: F, address: 8B, set the data written down at step
3), and press the PAUSE button.
2) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
5-21
8. Auto White Balance & LV Standard Data Input

Adjust the white balance reference at 3200K, and adjust the normal
coefficient of the light value.
Subject
Clear chart
Adjustment Page

F
Adjustment Address
3C to 41
Note1: This adjustment should be carried out upon completion of Color

reproduction adjustments.
Note2: After the power is turned on, this adjustment can be done only
once.
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Adjusting method:
Procedure
1
2
0
6
01
82
01
01
Set the data.

Set the data.
3
4
16
02
Set the data.

Wait for 2 sec.
01
11
01
0D
02

button.
button.
01. (Note4)

3C to 41.
Processing after Completing Adjustments

Procedure
1
6
01
00 Set the data, and press PAUSE
button.
2
16
00
82
00
4
5
01
00

button.
Set the data.
Set the data.
Perform Auto White Balance
Adjustment.
5-22
9. Auto White Balance Adjustment

Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility will
be poor.
Subject
Clear chart
Filter
Measurement Point
Filter C14 for color temperature

correction
Adjustment Page

F
Adjustment Address
Specified Value
Adjusting method:
1
42, 43
R ratio: 2B40 to 2BC0
B ratio: 5E20 to 5EE0
Note1: After the power is turned on, this adjustment can be done only
once.
Note2: Perform Auto White Balance & LV Standard Data Input before
this adjustment.
Note3: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX
Display data
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Procedure
Place the C14 filter for color
temperature correction on the lens.
Set the data.
01
01
3
4
6
F
82
B8
01
Set the data.

Write down the data.
B8
2B
B9

button.
B9
80
BA

button.
BA
5E

button.
button.
button.
10
BB
11
BB
80
12
01
A7
13
14
01
15
02
16
01
3F
17
18
0
1
03
04
19
03
05
20
A5
Wait for 2 sec.

button.
01. (Note4)
button.
Set the data.
Check that the display data (Note3)
satisfies the R ratio specified value.
Set the data.
satisfies the B ratio specified value.

42, 43.

Procedure
5-23
01
00
82
00
B8
B9
BA
BB
7
8
0
0
03
01

button.
Set the data.
Set the data that is written down
at step 4, and press PAUSE button.
Set the data that is written down at
step 6, and press PAUSE button.
00
00
Set the data.

Set the data.
10. White Balance Check

Subject
Clear chart
Filter
Measurement Point
Filter C14 for color temperature

correction
ND filter 1.0 and 0.4 and 0.1
Specified Value
Vectorscope
Fig. 5-1-12. A to B
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Checking method:
1
2
82
01
01
0F
01
00
6
7
01
3F
12
13
03
06
14
Fig. 5-1-12. (A)

R-Y
B-Y
1.5mm
3mm

button.
Check that the center of the white
luminance point is within the circle
shown Fig. 5-1-12. B.
Place the ND filter 1.5

(1.0+0.1+0.4) on the lens.
button.
0F
2mm

button.
Outdoor white balance check
Place the C14 filter on the lens.
10
01
B-Y

button.
Check that the center of the white
luminance point is within the circle
shown Fig. 5-1-12. A.
Remove the C14 filter.

LV data check
2mm
Check that the lens is not covered

with either filter.
Set the data.
11
R-Y
Procedure
Indoor white balance check
3mm
Fig. 5-1-12. (B)
Wait for 2 sec.

Set the data.
Check that the display data (Note)
satisfies the specified value.
Specified value: 0000 to 0BC0
Note: Displayed data of the adjustment remote commander.

1 : XX : XX
Display data

Procedure
1
01
00
82
00

button.
Set the data.
03
00
Set the data.
5-24
11. Angular Velocity Sensor Sensitivity Adjustment

Precautions on the Parts Replacement
There are two types of repair parts.
Type A: ENC03JA
Type B: ENC03JB
Replace the broken sensor with a same type sensor. If replace with
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations. After replacing, readjust according to the adjusting method after replacement.
Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.
Subject
Arbitrary
Measurement Point

Adjustment Page
Adjustment Address
F
5E, 5F
Specified Value
2900 to 4D00
Note1: Displayed data of the adjustment remote commander.

1 : XX : XX
Display data
Note2: SI-028 board: DCR-TRV230/TRV330
Switch setting:
1) STEADY SHOT (Menu display) ...................................... ON
2) ZOOM .......................................................................... Center
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
5E
6D
5F
67
6
7
0
1
03
11

button.
button.
Pitch sensor check
(SI-028/029 board SE301)
Set the data.
Yaw sensor check
(SI-028/029 board SE302)
03
12
Set the data.


Procedure
1
0
01
00 Set the data.
2
3
03
00
Set the data.

Move the camcorder, and check
that the steady shot operations
have been performed normally
5-25
1-4.
1. VCO Adjustment (CF-079/080 board)

Set the VCO free-run frequency. If deviated, the EVF screen will be
blurred.
Mode
Camera
ELECTRONIC VIEWFINDER SYSTEM

ADJUSTMENT
Note1: When replacing the LCD unit, be careful to prevent damages

caused by static electricity.
Note2: Switch setting:
LCD panel ........................................................................... Close
Note3: CF-079 board: DCR-TRV230/TRV330
[Adjusting connector]
Most of the measuring points for adjusting the viewfinder system
are concentrated in CN1108 of VC-254 board.
Connect the Measuring Instruments via the CPC-13 jig (J-6082443-A).
The following table shows the Pin No. and signal name of CN1108.
Subject
Measurement Point
Arbitrary
Pin qa of CN1108 of VC-254 board
(VCO)
Adjustment Page
Frequency counter
D
Adjustment Address
Specified Value
92, 93
f = 15734 30Hz
Adjusting method:
Procedure
1
0
01
01 Set the data.
Pin No.
Signal Name
Pin No.
Signal Name
1
SWP
11
VCO
2
AFC F0
12
EVF VG
3
BPF MONI
13
DV RF SWP
4
FO ADJ RF IN
14
RF IN
5
PB RF
15
CAP FG
6
REG GND
16
RF MON
7
RF AGC OUT
17
TMS
8
VC RF SWP
18
TCK
9
EVF VR (*1), COM DC (*2)
19
TDO
10
EVF VB (*1), N.C. (*2)
20
TDI
Table 5-1-10.
92
92
92
Change the data and set the VCO

frequency (f) to the specified value.
Press PAUSE button.
Read the data, and this data is
named D92.
Convert D92 to decimal notation,
and obtain D92. (Note)
5
6
CN1108
1
93
D93
01
00
Calculate D93 using following

equations (Decimal calculation)
When D92 231
D93=D92+24
When D92>231
D93=255
Convert D93 to a hexadecimal
number, and obtain D93. (Note)
button.
Set the data.
Note: Refer to Table 5-4-1. Hexadecimal-decimal Conversion Table.
20
Remove the
CPC lid (BT)
MI screw (M2 4) (H)
Fig. 5-1-13.
5-26
3. Contrast Adjustment (CF-079/080 board)

Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated
(whitish).
Mode
Camera
2. RGB AMP Adjustment (CF-079/080 board)

Set the D range of the RGB driver used to drive the LCD to the
specified value. If deviated, the LCD screen will become blackish
or saturated (whitish).
Mode
Camera
Subject
Measurement Point
Arbitrary
Pin qs of CN1108 OF VC-254 board
(EVF VG)
Subject
Measurement Point
Arbitrary
Pin qs of CN1108 of VC-254 board
(EVF VG)
Adjustment Page
Oscilloscope
D
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
95
A = 7.44 0.10V
Adjustment Address
Specified Value
99
A = 2.46 0.10V
Adjusting method:
Adjusting method:

Procedure
1
0
01
01 Set the data.
2
95
95
01
00

Procedure
1
0
01
01 Set the data.
Change the data and set the voltage

(A) between the reversed waveform
pedestal and non-reversed waveform
pedestal to the specified value.
Press PAUSE button.
99
99
Set the data.
01

(A) between the 100 IRE and 0 IRE
(pedestal) to the specified value.
(The data should be 00 to 7F.)
Press PAUSE button.
00
Set the data.
Pedestal
100 IRE
2H
2H
Pedestal
Pedestal
Fig. 5-1-14.
Fig. 5-1-15.
5-27
4. COM DC Adjustment
Set the reference level of the video signal for driving the LCD to an
appropriate level. If deviated, the screen image will be whitish.
Mode
Camera
Subject
Measurement Point
Arbitrary
+ probe: Pin qs of CN1108 of VC-254
board (EVF VG)
probe: Pin 9 of CN1108 of VC-254
board (COM DC)
Adjustment Page
Digital volt meter

D
Adjustment Address
Specified Value
94
A= +0.3 0.1Vdc
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
94
94
01
Change the data and set the DC

voltage (A) to the specified value.
Press PAUSE button.
00
Set the data.
5-28
1-5.
[LCD Type Check]

By measuring the resistor value between Pin 6 of CN5502 and
GND, the type of LCD can be discriminated.
LCD SYSTEM ADJUSTMENT
Note 1: The back light (fluorescent tube) is driven by a high voltage AC

power supply. Therefore, do not touch the back light holder to
avoid electrical shock.
Note 2: When replacing the LCD unit, be careful to prevent damages
Note 3: Set the LCD BRIGHT (Menu display) to the center.
Set the LCD COLOR (Menu display) to the center.
Note 4: PD-138 board: DCR-TRV230/TRV330
Resistor value 1.0k

LCD type
2.5 LCD TYPE SH
(61k)
PD board
PD-138
DCRTRV230/TRV330
Table 5-1-12.
[Adjusting connector]
Most of the measuring points for adjusting the LCD system are
concentrated in CN5502 of the PD-138/139 board. Connect the
measuring instruments via the multi CPC jig (J-6082-311-A). The
following table shows the Pin No. and signal name of CN5502.
Pin No.
1
3
5
7
9
Signal Name
VB
VG
VR
XHD
GND
Pin No.
2
4
6
8
10
[Adjusting Procedure]
DCR-TRV230/TRV330:
1. VCO adjustment
2. RGB AMP adjustment
3. Contrast adjustment
4. COM AMP adjustment
5. V-COM adjustment
6. White balance adjustment
Signal Name
XVD OUT
PANEL COM/PSIG
MAKER CHECK
XHD OUT
GND
DCR-TRV530:
1. VCO adjustment
3. Black limit adjustment
5. Center level adjustment
6. V-COM adjustment
Table 5-1-11.
10
PD-138/139 board
CN5502
Fig. 5-1-16.
5-29
47k
3.5 LCD TYPE SO
(123k)
PD-139
TRV530
1. VCO Adjustment (PD-138/139 board)

Set the VCO free-run frequency. If deviated, the LCD screen will
be blurred.
Mode
VTR stop
2. PSIG Gray Adjustment (PD-139 board)

(DCR-TRV530)
Set the uniformity improvement signal to an appropriate level.
Mode
VTR stop
Signal
Measurement Point
No signal
Pin 8 of CN5502 (XHD OUT)
Signal
Measurement Point
No signal
Pin 4 of CN5502 (PSIG)
Adjustment Page
Frequency counter
D
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
A2, A3
f = 15734 30Hz
Adjustment Address
Specified Value
A7
A = 5.00 0.1V
Adjusting method:
Adjusting method:

Procedure
1
0
01
01 Set the data.
2
A2
A2
A2

Procedure
1
0
01
01 Set the data.

Press PAUSE button.
named DA2.
Convert DA2 to decimal notation,
and obtain DA2. (Note)
5
6
A7
A7
01
Change the data and set the PSIG

signal level (A) to the specified
value. (The data should be 00
to 7F)
Press PAUSE button.
00
Set the data.
Calculate DA3 using following

[DCR-TRV230/TRV330]
When DA2 232
DA3=DA2+23
When DA2>232
DA3=255
[DCR-TRV530]
When DA2 246
DA3= DA2+9
When DA2>246
DA3=255
7
8
A3
DA3
01
00
Convert DA3 to a hexadecimal

number, and obtain DA3. (Note2)
button.
2H
Set the data.
Fig. 5-1-17.
5-30
3. RGB AMP Adjustment (PD-138 board)

(DCR-TRV230/TRV330)
Set the D range of the RGB decoder used to drive the LCD to the
Mode
VTR stop

(DCR-TRV530)
Set the D range of the RGB decoder used to drive the LCD to the
Mode
VTR stop
Signal
Measurement Point
No signal
Pin 3 of CN5502 (VG)
External trigger: Pin 4 of CN5502
(PANEL COM)
Signal
Measurement Point
No signal
(PSIG)
Adjustment Page
Oscilloscope
D
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
A5
A = 3.72 0.05V
Adjustment Address
Specified Value
A5
A = 7.58 0.05V
Adjusting method:
Adjusting method:

Procedure
1
0
01
01 Set the data.
2
A5
A5
01
00

Procedure
1
0
01
01 Set the data.

(The data should be 00 to 3F)
Press PAUSE button.
A5
A5
Set the data.
4
5
01

(The data should be 00 to FF)
Press PAUSE button.
00
Set the data.

Perform Black Limit Adjustment.
Pedestal
Pedestal
2H
Pedestal
Fig. 5-1-18.
2H
Pedestal
Fig. 5-1-19.
5-31
5. Black Limit Adjustment (PD-139 board)

(DCR-TRV530)
Set the dynamic range of the LCD driver to an appropriate level. If
deviated, the LCD screen will become blackish or saturated
(whitish).
Mode
VTR stop
Signal
Measurement Point
No signal
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
A6
A = 8.10 0.08V
6. Contrast Adjustment (PD-138 board)

(DCR-TRV230/TRV330)
(whitish).
Mode
VTR stop
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
3
2
2
0E
0F
A6
A6
61
5B
0E
0F
00
00
Set the data.

Set the data.
8
9
01
00
Set the data.

Check that the specified value of
RGB AMP Adjustment is
satisfied. If not, perform RGB
AMP Adjustment.
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
AA
A = 3.50 0.07V

Procedure
1
0
01
01 Set the data.
Change the data and set the PSIG

signal amplitude (A) to the specified
value.
Press PAUSE button.
2
2
No signal
(PANEL COM)
Adjusting method:
Set the data.

Set the data.
6
7
Signal
Measurement Point
AA
AA
01

Press PAUSE button.
00
Set the data.
100 IRE
2H
A
0 IRE
Fig. 5-1-21.
Fig. 5-1-20.
5-32

(DCR-TRV530)
(whitish).
Mode
VTR stop
Signal
Measurement Point
No signal
(PSIG)
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
AA
A = 2.76 0.07V
8. Center Level Adjustment (PD-139 board)

(DCR-TRV530)
Set the video signal center level of LCD panel to an appropriate
level.
Mode
VTR stop
AA
AA
01

Press PAUSE button.
00
Adjustment Page
Digital voltmeter
D
Adjustment Address
Specified Value
AB
A = 7.00 0.03Vdc

Procedure
1
0
01
01 Set the data.

Procedure
1
0
01
01 Set the data.
D
No signal
Adjusting method:
Adjusting method:
Signal
Measurement Point
Set the data.
100 IRE
2H
Pedestal
Fig. 5-1-22.
5-33
AB
AB
01
Change the data and set the DC

voltage (A) to the specified value.
Press PAUSE button.
00
Set the data.
9. COM AMP Adjustment (PD-138 board)

(DCR-TRV230/TRV330)
Set the common electrode drive signal level of LCD to the specified
value.
Mode
VTR stop
Signal
Measurement Point
No signal
Pin 4 of CN5502 (PANEL COM)
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
A7
A = 6.36 0.05V
10. V-COM Adjustment (PD-138/139 board)

Set the DC bias of the common electrode drive signal of LCD to the
specified value.
If deviated, the LCD display will move, producing flicker and
conspicuous vertical lines.
Mode
VTR stop
Signal
Measurement Point
Adjustment Page
Adjustment Address
Specified Value
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
A7
A7
01
D
A4
The brightness difference between the
section A and section B is minimum.
Note: This adjustment should be carried out upon completion of the

following adjustments.
[DCR-TRV230/TRV330]
RGB AMP Adjustment
Contrast Adjustment
COM AMP Adjustment
[DCR-TRV530]
RGB AMP Adjustment
Black Limit Adjustment
Contrast Adjustment
Center Level Adjustment
Change the data and set the

PANEL COM signal level (A) to
the specified value.
Press PAUSE button.
00
No signal
Check on LCD display
Set the data.
Adjusting method:
Procedure
1
0
01
01 Set the data.
A4
Change the data so that the

brightness of the section A and
that of the section B is equal.
[DCR-TRV230/TRV330]
The data should be 00 to FF.
[DCR-TRV530]
The data should be 00 to 3F
A4
A4
[DCR-TRV230/TRV330]
Subtract 8 from the data.
[DCR-TRV530]
Press PAUSE button.
01
2H
Fig. 5-1-23.
00
Set the data.
Fig. 5-1-24.
5-34
11. White Balance Adjustment (PD-138/139 board)

Correct the white balance.
If deviated, the reproduction of the LCD screen may degenerate.
Mode
VTR stop
Signal
Measurement Point
No signal
Check on LCD screen
Adjustment Page
Adjustment Address
Specified Value
A8, A9
The LCD screen should not be colored.
Note1: Check the white balance only when replacing the following parts.
If necessary, adjust them.
1. LCD panel
2. Light induction plate
3. IC5501
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
A8
80
A9
80
A9
A8
A8
A9
A9
A9
10
01

button.
button.
Check that the LCD screen is not
colored. If not colored, proceed to
step 10.
Change the data so that the LCD
screen is not colored.
Press PAUSE button.
Change the data so that the LCD
screen is not colored.
Press PAUSE button.
00
If the LCD screen is colored,

repeat steps 5 to 9.
Set the data.
5-35
2-1-2.
5-2. MECHANISM SECTION

ADJUSTMENT
1. Preparations for Adjustment

1) Clean the tape path face (tape guide, capstan shaft, pinch roller).
2) Connect the adjustment remote commander to the LANC jack.
3) Turn on the HOLD switch of the adjustment remote
commander.
5) Select page: 2, address: 2E, and set data: 02.
button of the adjustment remote commander.
(Be sure to perform Processing after operation after
completing adjustments.)
7) Connect the oscilloscope to VC-254 board CN1108 via CPC13 jig (J-6082-443-A).
Channel 1: VC-254 board, CN1108 Pin 5
External trigger: VC-254 board, CN1108 Pin 8
8) Playback Hi8/standard8 alignment tape for tracking.
(WR5-1NP)
9) Check that the oscilloscope RF waveform is normal at the
entrance and exit.
If not normal, adjust according to the separate volume
8mm Video Mechanical Adjustment Manual IX M2000
Mechanism .
10) Perform Processing after operations, after completing
adjustment.
Mechanism Section adjustments, checks, and replacement of

mechanism parts, refer to the separate volume 8mm Video
Mechanism Adjustment Manual IX M2000 Mechanism .
2-1.
TAPE PATH ADJUSTMENT
Hi8/STANDARD8 MODE
2-1-1. OPERATING WITHOUT CASSETTE

1) Refer to Section 2. DISASSEMBLY and supply the power
with the cabinet assembly removed. (So that the mechanical
deck can be operated.)
3) Turn on the HOLD switch of the adjustment remote
commander.
4) Close the cassette compartment without loading a cassette and
complete loading.
8) Disconnect the power supply of the unit, and connect it again.
By carrying out the above procedure, the unit can be operated
without loading a cassette. (Note2)
Be sure to carry out Processing after Operations after
checking the operations.
Set the data of page: D, address: 10 to 12, if the sensor
ineffective mode, forced VTR power supply ON mode is to be
used together.
CN1108 of VC-254 board

Pin No.
Signal Name
Pin No.
1
SWP
11
2
AFC F0
12
3
BPF MONI
13
4
F0 ADJ RF IN
14
5
PB RF
15
6
REG GND
16
7
RF AGC OUT
17
8
VC RF SWP
18
9
EVF VR/COM DC
19
10
EVF VB/N.C.
20
Table 5-2-1.
Note 2: Except for the camera recording mode.
[Procedure after checking operations]

6) Disconnect the power supply of the unit.
Signal Name
VCO
EVF VG
DV RF SWP
RF IN
CAP FG
RF MON
TMS
TCK
TDO
TDI
[Procedure after operations]

1) Connect the adjustment remote commander, and turn on the
HOLD switch.
6) Remove the power supply from the unit.
Check this section
(Normal waveform)
Entrance side
CH1
Fig. 5-2-1.
CH2
(Trigger)
V
Fig. 5-2-1.
5-36
Exit side
2-2.
1)
2)
3)
4)
2-2-3.
DIGITAL8 MODE
2-2-1.
HOW TO ENTER RECORD MODE WITHOUT

CASSETTE
1. Recording of the tape path check signal

1) Clean the tape running side (tape guide, capstan shaft, pinch
roller).
3) Turn the HOLD switch of the adjustment remote commander
to the ON position.
4) Set to the camera recording mode.
5) Select page: 3, address: 1C, set data: 5D, and press the PAUSE
6) Record for several minutes.
7) Release the recording mode.
8) Select page: 3, address: 1C, set data: 00, and press the PAUSE
button.
Connect the adjustment remote commander to the LANC jack.

Turn the HOLD switch of the adjustment remote commander
to the ON position.
Close the cassette compartment without the cassette.
Select page: 3, address: 01, and set data: 0C, and press the
PAUSE button of the adjustment remote commander.
(The mechanism enters the record mode automatically.)
Note: The function buttons becomes inoperable.
5)
To quit the record mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the record mode, be
sure to quit following this procedure.)
2. Tape path check

1) Clean the tape running side (tape guide, capstan shaft, pinch
roller).
3) Turn the HOLD switch of the adjustment remote commander
to the ON position.
4) Connect an oscilloscope to VC-254 board CN1108 via the CPC13 jig (J-6082-443-A).
Channel 1: VC-254 board, CN1108 Pin qh (Note)
External trigger: VC-254 board, CN1108 Pin qd
2-2-2.
1)
2)
3)
4)
HOW TO ENTER PLAYBACK MODE WITHOUT

CASSETTE
Connect the adjustment remote commander to the LANC jack.
Turn the HOLD switch of the adjustment remote commander
to the ON position.
Close the cassette compartment without the cassette.
Select page: 3, address: 01, and set data: 0B, and press the
PAUSE button of the adjustment remote commander.
(The mechanism enters the playback mode automatically.)
Note: The function buttons becomes inoperable.
5)
OVERALL TAPE PATH CHECK
Note: Connect a 75 resistor between Pins qh of CN1108 and 6

(GND).
To quit the playback mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the playback mode,
be sure to quit following this procedure.)
5)
6)
7)
8)
9)
Select page: 2, address: 2E, and set data: 01.

Playback the tape path check signal.
Select page: 3, address: 33, and set data: 08.
Check that the oscilloscope RF waveform is flat at the entrance
and exit.
If not flat, perform 2-1-2. TAPE PATH ADJUSTMENT of
2-1. Hi8/STANDARD 8 MODE.
Must be flat
Pin qh
Pin qd
Fig. 5-2-2.
5-37
5-3. VIDEO SECTION ADJUSTMENT

3-1.
PREPARATIONS BEFORE ADJUSTMENTS
Use the following measuring instruments for video section

adjustments.
3-1-1.
Equipment to Required
1)
2)
TV monitor
Oscilloscope (dual-phenomenon, band width above 30 MHz
with delay mode) (Unless specified otherwise, use a 10 : 1
probe.)
3) Frequency counter
4) Pattern generator with video output terminal
5) Digital voltmeter
6) Audio generator
7) Audio level meter
8) Audio distortion meter
9) Audio attenuator
10) Regulated power supply
11) Digital8 alignment tapes
SW/OL standard (WR5-2D)
Parts code: 8-967-993-22
Audio operation check for NTSC (WR5-3ND)
Parts code: 8-967-993-32
System operation check for NTSC (WR5-5ND)
Parts code: 8-967-993-42
12) Hi8/standard8 alignment tapes
For tracking adjustment (WR5-1NP)
Parts code : 8-967-995-02
For video frequency characteristics adjustment (WR5-7NE)
Parts code : 8-967-995-13
For checking Standard 8 mode operations
For LP (WR5-4NL)
Parts code : 8-967-995-51
For SP (WR5-5NSP)
Parts code : 8-967-995-42
Note : The following alignment tapes can also be used.
WR5-4NSP (8-967-995-41)
For checking Hi8 mode operations

For LP (WR5-8NLE)
Parts code : 8-967-995-52
For SP (WR5-8NSE)
Parts code : 8-967-995-43
For Checking AFM stereo operations (WR5-9NS)
Parts code : 8-967-995-23
For BPF adjustment (WR5-11NS)
Parts code : 8-967-995-71
13) Adjustment remote commander (J-6082-053-B)
14) CPC-13 jig (J-6082-443-A)
15) Power code (J-6082-223-A)
Note : Connect the adjustment remote commander to the LANC jack,
and set the HOLD switch to the ADJ side.
16) IR receiver jig (J-6082-383-A)

17) Extension cable (100P, 0.5mm)(J-6082-352-A)
For extension between the PC-082 board (CN1901) and the
VC-254 board (CN1104).
5-38
3-1-2.
Note4: Setting the Forced VTR Power ON mode (VTR mode)

button.
The above procedure will enable the VTR power to be turned on
with the cabinet (L) assembly (SS-1380 block) removed.
After completing adjustments, be sure to exit the Forced VTR
Power ON mode.
Note5: Setting the Forced Camera Power ON mode (Camera mode)
button.
The above procedure will enable the camera power to be turned
on with the cabinet (L) assembly (SS-1380 block) removed.
After completing adjustments, be sure to exit the Forced Camera
Power ON mode.
Note6: Exiting the Forced Power ON mode
button.
Precautions on Adjusting
Note1: SI-028 board: DCR-TRV230/TRV330

Note2: CF-079 board: DCR-TRV230/TRV330
Note3: CD-292 board: DCR-TRV230/TRV330
1)
2)
3)
4)
5)
6)
7)
8)
The adjustments of this unit are performed in the VTR mode

or camera mode.
To set to the VTR mode, set the power switch to VCR or
PLAYER or set the Forced VTR Power ON mode using the
adjustment remote commander (Note4).
To set to the Camera mode, set the power switch to CAMERA
or set the Forced Camera Power ON mode using the
adjustment remote commander (Note5).
After completing adjustments, be sure to exit the Forced VTR
Power ON Mode or Forced Camera Power ON Mode.
(Note6)
The front panel block (SI-028/029 board, focus ring, microphone
unit) need not be connected except during IR transmitter
adjustment and Audio adjustment. To remove, disconnect
the following connector.
VC-254 board CN1116 (26P 0.5mm)
As removing the cabinet (R) assembly (removing CN1117 of
the VC-254 board) means removing the lithium 3V power
supply (BT101 on the CF-079/080 board), data such as date,
time, user-set menus will be lost. After completing adjustments,
reset these data. If the cabinet (R) assembly has been removed,
the self-diagnosis data, data on history of use (total drum
rotation time etc.) will be lost. Before removing, note down
the self-diagnosis data (data of page: 2, address: B0 to C6) and
the data on history use (data of page: 2, address: A2 to AA).
(Refer to 5-4.Service Mode.)
The cabinet (R) assembly (CF-079/080 board, LCD block,
viewfinder block) need not be connected to operate the VTR
block. (Use the adjustment remote commander, to operate the
VTR block.) When removing the cabinet (R) assembly,
disconnect the following connector.
1. VC-254 board CN1117 (45P, 0.5mm)
2. VC-254 board CN1120 (20P, 0.8mm)
The Memory stick connector need not be connected. To remove,
disconnect the following connector.
(DCR-TRV330/TRV530)
PC-082 board CN1153 (12P 0.5mm)
To open the PC-082 board, disconnect the following connectors.
(DCR-TRV330/TRV530)
1. PC-082 board CN1152 (6P 0.5mm)
2. PC-082 board CN1901 (100P 0.5mm)
And use the following extension cable between the PC-082
board CN1901 and VC-254 board CN1104.
J-6082-352-A (100P, 0.5mm)
The lens block (CD-292/315 board) need not be connected. To
remove, disconnect the following connectors.
1. VC-254 board CN1501 (16P, 0.5mm)
2. VC-254 board CN1551 (24P, 0.5mm)
By setting the Forced VTR Power ON mode or Forced
Camera Power ON mode, the video section can be operate
even if the cabinet (L) assembly (SS-1380 block) has been
removed. When removing the cabinet (L) assembly, disconnect
the following connector.
FU-150/154 board CN402 (12P 0.8mm)
5-39
3-1-3. Adjusting Connectors

Some of the adjusting points of the video section are concentrated
at VC-254 board CN1108. Connect the measuring instruments via
the CPC-13 jig (J-6082-443-A). The following table lists the pin
numbers and signal names of CN1108.
Pin No.
Signal Name
Pin No.
Signal Name
1
SWP
11
VCO
2
AFC F0
12
EVF VG
3
BPF MONI
13
DV RF SWP
4
FO ADJ RF IN
14
RF IN
5
PB RF
15
CAP FG
6
REG GND
16
RF MON
7
RF AGC OUT
17
TMS
8
VC RF SWP
18
TCK
9
EVF VR (*1), COM DC (*2)
19
TDO
10
EVF VB (*1), N.C. (*2)
20
TDI
CN1108
1
20
Remove the
CPC lid (BT)
MI screw (M2 4) (H)
Fig. 5-3-1.
Table 5-3-1.
3-1-4. Connecting the Equipment
Connect the measuring instruments as shown in Fig. 5-3-2 and
perform the adjustments.
VTR recording mode

Pattern generator
Video output
(75 )
VIDEO
(Yellow)
Adjustment
remote
commander
AUDIO L
(White)
Main unit
AUDIO R
(Red)
LANC jack
AUDIO/VIDEO jack
Playback mode
TV monitor
VIDEO
(Yellow)
Main unit
AUDIO L (White)
Adjustment
remote
commander
AUDIO R (Red)
LANC jack
AUDIO/VIDEO jack
Fig. 5-3-2.
5-40
3-1-5. Alignment Tape

The following table lists alignment tapes which are available.
Use the tape specified in the signal column for each adjustment. If
the type of tape to be used for checking operations is not specified,
use whichever type.
Fig.5-3-3. shows the 75% color bar signals recorded on the alignment
tape.
Note: Measure using the VIDEO terminal (Terminated at 75).
White (100%)
Cyan
White (75%)
Green
Yellow
Digital8 alignment tape

Name
Usage
SW/OL standard
Switching position adjustment
(WR5-2D)
Audio operation check Audio system adjustment
(WR5-3ND),
Video frequency
characteristics
WR5-7NE
Operation check
(SP mode)
WR5-5NSP
Operation check
(SP mode)
WR5-8NSE
Operation check
(LP mode)
WR5-4NL
Operation check
(LP mode)
WR5-8NLE
AFM stereo
Operation check
WR5-9NS
BPF adjustment
WR5-11NS
0.286V
Operation check
0.286V
Standard 8 MP
Hi8
SP
ME
SP
Standard 8 MP
SP
Hi8
ME
SP
Standard 8 MP
LP
Hi8
ME
LP
Standard 8 MP
SP
Standard 8 MP
SP
Horizontal sync signal

Color bar signal waveform
White
(100%)
Blue
Red
White
(75%)
Magenta
Tape path
adjustment
Switching
position
adjustment
Frequency
characteristics
adjustment
Green
Usage
Cyan
Hi8/standard 8 alignment tape

Record
Tape Tape
Name
-ing
type speed
mode
Tracking
WR5-1NP
0.714V
1V
Yellow
System operation check

(WR5-5ND)
Magenta
Burst signal
Red
Blue
Black
Fig. 5-3-3. Color Bar Signal of the Alignment Tape
3-1-6. Input/output Level and Impedance

Video input/output
Special stereo minijack, 1Vp-p, 75, unbalanced, sync negative
S video input/output
4-pin mini DIN
Luminance signal: 1Vp-p, 75, unbalanced, sync negative
Chrominance signal: 0.286Vp-p, 75, unbalanced
Audio input/output
Special stereo minijack:
Input: 7.5dBs, input impedance more than 47k
Output:7.5dBs, (at load impedance 47k), impedance less
than 2.2k
Checking
operations
AFM stereo
Checking
operations
BPF
adjustment
Tape type
ME ......... Particle type metal tape
MP .......... Evaporated type metal tape
5-41
3-2.
2-2. Serial No. Input

Write the serial No. and model code in the EEPROM (nonvolatile
memory). Convert the serial No. on the name plate from decimal to
hexadecimal, and write in the EEPROM.
Page
C
SYSTEM CONTROL SYSTEM ADJUSTMENT
1. Initialization of B, C, D, E, F, 7, 8 Page Data

If the B, C, D, E, F, 7, 8 page data is erased due to some reason,
perform 1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE
DATA, of 5-1. CAMERA SECTION ADJUSTMENT.
Address
2. Serial No. Input

2-1. Company ID Input
Write the company ID in the EEPROM (nonvolatile memory).
Page
C
Address
Input method:
2) Read the serial No. on the name plate, and take it as D1.
Example: If the serial No. is 77881.
D1=77881
E8, E9, EA, EB, EC
Note: Use six digits of the low rank when a serial No. is more than
seven digits.
Input method:
2) Input the following data to page: C, addresses: E8 to EC.
3)
Obtain D2 and H1 corresponding to D1 from Table 5-3-2.

Example: If D1 is 77881.
D2=D165536=12345
H1=FE
H1 (Hexadecimal)
D1 (Decimal)
D2 (Decimal)
(Service model code)
000001 to 065535 D1
FE
065536 to 131071 D165536
FE
131072 to 196607 D1131072
FE
Note: Press the PAUSE button of the adjustment remote commander

each time to set the data.
Address
E8
E9
EA
EB
EC
3)
ED, EE, EF
Data
08
00
46
01
02
Table 5-3-2.
4)
Input H1 to page: C, address: ED. (Model code input)

Example: If H1 is FE.
Select page: C, address: ED, set data: FE, and
press the PAUSE button.
5) Obtain the maximum decimal not exceeding D2 from Table 53-3, and take this as D3.
D3=12288
6) Obtain the hexadecimal corresponding to D3 from Table 5-3-3,
and take this as H3.
H3=3000
7) Obtain the difference D4 between D 2 and D 3. (Decimal
calculation, 0 D4 255)
D4= D2D3
Example: If D2 is 12345 and D3 is 12288.
D4=1234512288=57
8) Convert D4 to hexadecimal, and take this as H4.
(Refer to Hexadecimal-decimal conversion table in 5-4.
Service Mode.)
H4=39
9) Input the upper 2 digits of H3 to page: C, address: EE.
Example: If H3 is 3000.
Select page: C, address: EE, set data: 30, and
10) Input H4 to page: C, address: EF.
Example: If H4 is 39.
Select page: C, address: EF, set data: 39, and
5-42
HexaHexaHexaHexaHexaHexaHexaHexaDecimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal
(D3)
(D3)
(D3)
(D3)
(D3)
(D3)
(D3)
(D3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
0
256
512
768
1024
1280
1536
1792
2048
2304
2560
2816
3072
3328
3584
3840
4096
4352
4608
4864
5120
5376
5632
5888
6144
6400
6656
6912
7168
7424
7680
7936
0000
0100
0200
0300
0400
0500
0600
0700
0800
0900
0A00
0B00
0C00
0D00
0E00
0F00
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
1A00
1B00
1C00
1D00
1E00
1F00
8192
8448
8704
8960
9216
9472
9728
9984
10240
10496
10752
11008
11264
11520
11776
12032
12288
12544
12800
13056
13312
13568
13824
14080
14336
14592
14848
15104
15360
15616
15872
16128
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
2A00
2B00
2C00
2D00
2E00
2F00
3000
3100
3200
3300
3400
3500
3600
3700
3800
3900
3A00
3B00
3C00
3D00
3E00
3F00
16384
16640
16896
17152
17408
17664
17920
18176
18432
18688
18944
19200
19456
19712
19968
20224
20480
20736
20992
21248
21504
21760
22016
22272
22528
22784
23040
23296
23552
23808
24064
24320
4000
4100
4200
4300
4400
4500
4600
4700
4800
4900
4A00
4B00
4C00
4D00
4E00
4F00
5000
5100
5200
5300
5400
5500
5600
5700
5800
5900
5A00
5B00
5C00
5D00
5E00
5F00
24576
24832
25088
25344
25600
25856
26112
26368
26624
26880
27136
27392
27648
27904
28160
28416
28672
28928
29184
29440
29696
29952
30208
30464
30720
30976
31232
31488
31744
32000
32256
32512
6000
6100
6200
6300
6400
6500
6600
6700
6800
6900
6A00
6B00
6C00
6D00
6E00
6F00
7000
7100
7200
7300
7400
7500
7600
7700
7800
7900
7A00
7B00
7C00
7D00
7E00
7F00
32768
33024
33280
33536
33792
34048
34304
34560
34816
35072
35328
35584
35840
36096
36352
36608
36864
37120
37376
37632
37888
38144
38400
38656
38912
39168
39424
39680
39936
40192
40448
40704
Table 5-3-3.
5-43
8000
8100
8200
8300
8400
8500
8600
8700
8800
8900
8A00
8B00
8C00
8D00
8E00
8F00
9000
9100
9200
9300
9400
9500
9600
9700
9800
9900
9A00
9B00
9C00
9D00
9E00
9F00
40960 A000 49152

41216 A100 49408
41472 A200 49664
41728 A300 49920
41984 A400 50176
42240 A500 50432
42496 A600 50688
42752 A700 50944
43008 A800 51200
43264 A900 51456
43520 AA00 51712
43776 AB00 51968
44032 AC00 52224
44288 AD00 52480
44544 AE00 52736
44800 AF00 52992
45056 B000 53248
45312 B100 53504
45568 B200 53760
45824 B300 54016
46080 B400 54272
46336 B500 54528
46592 B600 54784
46848 B700 55040
47104 B800 55296
47360 B900 55552
47616 BA00 55808
47872 BB00 56064
48128 BC00 56320
48384 BD00 56576
48640 BE00 56832
48896 BF00 57088
C000
C100
C200
C300
C400
C500
C600
C700
C800
C900
CA00
CB00
CC00
CD00
CE00
CF00
D000
D100
D200
D300
D400
D500
D600
D700
D800
D900
DA00
DB00
DC00
DD00
DE00
DF00
57344
57600
57856
58112
58368
58624
58880
59136
59392
59648
59904
60160
60416
60672
60928
61184
61440
61696
61952
62208
62464
62720
62976
63232
63488
63744
64000
64256
64512
64768
65024
65280
E000
E100
E200
E300
E400
E500
E600
E700
E800
E900
EA00
EB00
EC00
ED00
EE00
EF00
F000
F100
F200
F300
F400
F500
F600
F700
F800
F900
FA00
FB00
FC00
FD00
FE00
FF00
3-3.
2. PLL fo & LPF fo Pre-Adjustment (VC-254 board)
SERVO AND RF SYSTEM ADJUSTMENT
Before perform the servo and RF system adjustments, check that

the specified value of 27MHz Origin Oscillation Adjustment of
VIDEO SYSTEM ADJUSTMENT is satisfied.
Adjusting Procedure:
1. REEL FG adjustment
2. PLL fo & LPF fo pre-adjustment
3. Switching position adjustment
4. AGC center level and APC & AEQ adjustment
5. PLL fo & LPF fo fine adjustment
6. Hi8/Standrd8 switching position adjustment
7. CAP FG offset adjustment
Mode
VTR stop
Measurement Point
Display data of page: 3, address: 03

Adjustment Page
Adjustment Address
C
1F, 20, 22, 29
Specified Value
The data of page: 3, address: 02 is 00.

Adjusting method:
1. REEL FG Adjustment (VC-254 board)

Compensates the dispersion of the hall elements.
Measurement Point
1
2
0
3
01
01
Adjustment Page

C
02
Adjustment Address
Specified Value
17, 30
00 or 01 or 04 or 05
03
01
01
30
Procedure
Set the data.
button.
00 within 10 sec. (Note)
Check that the data is 00. (Note)
00
Set the data.
Note: If it isnt satisfied, select page: C, address: 21, set the following
data, and press the PAUSE button, and repeat steps 2 to 4.
Adjusting method:
Procedure
1
Close the cassette compartment
without inserting a cassette.
2
3
0
3
01
01
01
1C
02

00,
03
01
Check that the data is 00 or

01 or 04 or 05. (Note)
Set the data.
00
Setting data
When the data of page: C, address: 21 is CA. CE
When the data of page: C, address: 21 is CE. C6
Set the data.

button.
When the data of page: C, address: 21 is C6.

When the data of page: C, address: 21 is D2
If bit2, bit3, bit4, bit5 or bit6 of page: 3, address: 03 data is 1,

there are errors.
For the error contents, see the following table. (For the bit values,
refer to 5-4. SERVICE MODE, 4-3. 3. Bit value discrimination.)
Note: If the data is other value, adjustment has errors. (Take an appropriate
remedial measures according to the errors referring to the following
table.)
Data
02, 03, 06, 07
Contents of defect
T reel is defective
08, 09, 0C, 0D

0A, 0B, 0E, 0F
S reel is defective
S reel and T reel are defective
D2
C2
5-44
Bit value of page: 3,
Error contents
address: 03 data
bit 2 = 1 or bit 3 = 1
PLL fo fine adjustment is defective
bit 4 = 1 or bit 5 = 1
bit 6 = 1
PLL fo adjustment is defective

LPF fo is defective
3. Switching Position Adjustment (VC-254 board)

To obtain normal playback waveform output during the Digital8
playback mode, adjust the switching position.
Mode
VTR playback
Signal
Measurement Point
SW/OL reference tape (WR5-2D)

Adjustment Page

C
Adjustment Address
Specified Value
10, 11, 12, 13

00
4. AGC Center Level and APC & AEQ Adjustment

4-1. Preparations before adjustments
Mode
Camera recording
Subject
Note: Use a Hi8 MP tape.
Adjusting method:
1
2
Adjusting method:
0
3
01
21
01
01
0D
02
03
10
01
00
01
C8
Procedure
Set the data.
Set the data.
Record the camera signal for three
minutes.
Signal
Recorded signal at Preparations

before adjustments
Pin qh of CN1108 (RF MON) (Note 1)
Ext. trigger: Pin qd of CN1108 (DV RFSWP)

button.
00.
Measurement Point
Adjustment Page
Oscilloscope
C
Check that the data is 00.

(Note2)
Check that the data is other than
EE. (Note3)
Adjustment Address
Specified Value
1E
The data of page: 3, address: 03 is 00
Note 1: Connect a 75 resistor between Pin qh and Pin 6 (GND) of CN1108.

75 resistor (Parts code: 1-247-804-11)
Set the data.
Adjusting method:
1
Data of page:C,
address:10
Contents of defect
EE
Writing into EEPROM (IC4502) is

defective
Adjustment data is out of range
01
01
3
4
2
3
2E
33
01
08
Set the data.

Set the data.
23
Confirm that the playback RF

signal is stable. (Fig. 5-3-4.)
Set the data, and press PAUSE button.
01
7
8
3
3
02
03
No data is returned from IC3301

(CAIN)
Procedure
Playback the recorded signal at
Preparations before adjustments
Set the data.
When the A channel is defective
E7
01
2A
4-2. AGC Center Level Adjustment (VC-254 board)

Mode
Playback
Set the data.

(Note1)
Note 1: If the data of page: 3, address: 21 is 72, the tape top being played.
After playing the tape for 1 to 2 seconds, stop it, perform step 4
and higher.
Note 2: If bit 0 of the data is 1, the A channel is defective. If bit 1 is 1,
the B channel is defective. Contents of the defect is written into
page: C, addresses: 10 and 12. See the following table. (For the bit
values, refer to 5-4. SERVICE MODE, 4-3. 3. Bit value
discrimination. ) If bit3 of the data is 1, the tape end being
played, and adjustment has errors.
Note 3: If the data is EE rewind the tape and repeat steps 1 to 7.
E8
0
8

Procedure
1
Insert the SW/OL reference tape
and enter the VTR STOP mode.
2
3
Arbitrary

(Note2)
Perform APC & AEQ Adjustment.
Note 2: If the data of page: 3, address: 03 is other than 00, adjustment

has errors.
PB RF signal is stable
When the B channel is defective

Data of page:C,
Contents of defect
address:12
E8
E7
Adjustment data is out of range
Pin qh
No data is returned from IC3301

(CAIN)
Pin qd
13.3 msec
Fig. 5-3-4.
5-45
4-3. APC & AEQ Adjustment (VC-254 board)

Mode
Playback
Signal
Measurement Point
Recorded signal at Preparations

before adjustments
Pin qh of CN1108 (RF MON) (Note 1)
Ext. trigger: Pin qd of CN1108 (DV RF
SWP)
Adjustment Page
Oscilloscope
C
Adjustment Address
Specified Value
18, 19, 1B, 1C, 21, 2C

The data of page: 3, address: 03 is 00
4-4. Processing after Completing Adjustments

Note 1: Connect a 75 resistor between Pin qh and Pin 6 (GND) of

CN1108.
75 resistor (Parts code: 1-247-804-11)
Note 2: The AGC Center Level Adjustment must have already been
completed before starting this adjustment.
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
3
C
C
18
19
25
25

4
5
C
C
1B
1C
25
25

6
7
C
C
21
2C
CA
03

8
9
10
Playback the recorded signal at

Preparations before adjustments
2
3
2E
33
01
08
Set the data.
07
Confirm that the playback RF

signal is stable. (Fig. 5-3-5.)
11
12
01
13
02
14
03
15
Check that the data changes from

07 to 00 in about 20 seconds
after pressing PAUSE button.
(Note3)
Perform Processing after
Completing Adjustments.
Note 3: If the data is other than 00, adjustment has errors.
PB RF signal is stable
Pin qh
Pin qd
13.3 msec
Fig. 5-3-5.
5-46
Procedure
1
2
0
2
01
2E
01
00
Set the data.

Set the data.
3
4
3
8
33
2A
00
00
Set the data.

button.
01
00
Set the data.
6. Hi8/Standard8 Switching Position Adjustment

(VC-254 board)
If deviated in this case causes switching noise or jitter on the Hi8/
Standard8 mode played back screen.
Mode
Playback
5. PLL fo & LPF fo Fine Adjustment (VC-254 board)

Mode
VTR stop
Signal
Measurement Point
Arbitrary
Display data of page: 3
Adjustment Page

C
Adjustment Address
Specified Value
1F, 20, 22, 29

Signal
Measurement Point
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
01
02
03
01
30
00

button.
00 within 10 sec.
bit 2 = 1 or bit 3 = 1
bit 4 = 1 or bit 5 = 1
bit 6 = 1
PLL fo fine adjustment is defective

PLL fo adjustment is defective
LPF fo is defective
Oscilloscope
F
Adjustment Address
Specified Value
62, 63
t1=0 10 sec

Procedure
1
Set to the stop mode.
Note: If bit2, bit3, bit4, bit5 or bit 6 of the data is 1, there are errors.
For the error contents, see the following table. (For the bit values, refer
to 5-4. SERVICE MODE, 4-3. 3. Bit value discrimination. )
Error contents
Adjustment Page
Adjusting Method:

(Note)
Set the data.
Bit value of page: 3,

address: 03
Hi8/Standard8 alignment tape:

For tracking adjustment
(WR5-1NP)
CH1: Pin 8 of CN1108 (VC RF SWP)
CH2: Pin 5 of CN1108 (PB RF)
2
3
0
F
01
22
01
C0
Set the data.

button.
4
5
2E
02
Set the data.

Set to the playback mode.
62
62
63
9
10
F
F
63
22
80
Press PAUSE button

button.
11
12
2
0
2E
01
00
00
Set the data.

Set the data.
Change the data and minimize

t1. (Coarse adjustment)
Press PAUSE button
Change the data and adjust so
that the switching position (t1)
becomes the specified value.
(Fine adjustment)
CH1
CH2
Enlargement
CH1
t1=0 10 sec
CH2
Fig. 5-3-6.
5-47
7. CAP FG Offset Adjustment (VC-254 board)

Set the Cap FG signal duty cycle to 50% to establish an appropriate
capstan servo. If deviated, the uneven rotation of capstan and noise
can occur in the Hi8/Standard8 LP mode.
Mode
Playback
Signal
Measurement Point
Hi8/standard 8 alignment tape :

For checking operation
(WR5-5NSP)
Pin qg of CN1108 (CAP FG)
Adjustment Page
Oscilloscope
F
Adjustment Address
Specified value
64
Duty = 50 1 %
Adjusting method:
Procedure
1
Set to the stop mode.
2
3
0
2
01
2E
4
5
01
02
01
01
02
Set the data.

Set the data.
81
Set to the playback mode.

button.
00
9
10

01.
button.
Check that Duty of CAP FG
signal satisfies the specified
value. If not, repeat steps 5 to 8.
2
0
2E
01
00
00
Set the data.

Set the data.
Center of movement
A
B
Duty = A/B 100 [%]
Fig. 5-3-7.
5-48
3-4.
2. Chroma BPF fo Adjustment (VC-254 board)

Set the center frequency of IC3701 chroma band-pass filter.
Mode
VTR stop
VIDEO SYSTEM ADJUSTMENTS
1. 27MHz Origin Oscillation Adjustment

(VC-254 board)
Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color will
become inconsistent.
Mode
Camera
Signal
Measurement Point
No signal
CH1: Chroma signal terminal of S
VIDEO OUT jack (75 terminated)
CH2: Y signal terminal of S VIDEO
OUT jack (75 terminated)
Subject
Measurement Point
Not required
Pin qh of IC1502
Adjustment Page
Oscilloscope
C
Adjustment Page
Frequency counter
F
Adjustment Address
Specified Value
Adjustment Address
Specified Value
4D
f=13500000 68Hz
28
A = 100mVp-p or less
B = 200mVp-p or more
Adjusting method:
Adjusting method:

Procedure
1
0
01
01 Set the data.

Procedure
1
0
01
01 Set the data.
2
4D
4D
01

frequency (f) to the specified
value.
Press PAUSE button.
00
11
10

button.
Check that the burst signal (B) is
output to the chroma signal
terminal of S VIDEO OUT jack.
0C
04
28

button.
Change the data for minimum
amplitude of the burst signal
level (A).
(The data should be 00 to 07.)
6
7
C
3
28
0C
00
11
00
10
01
00
Set the data.
24 13
25
12
36
IC1502
37 48
VC-254 board
Press PAUSE button.

button.
Check that the burst signal level
(B) satisfies the specified value.
button.
Set the data.
When the data of page: 3, address: 0C, is 04:

A
CH1
Fig. 5-3-8.
CH2
When the data of page: 3, address: 0C, is 00:
CH1
Fig. 5-3-9.
5-49
4. S VIDEO OUT Chroma Level Adjustment

(VC-254 board)
Mode
VTR stop
3. S VIDEO OUT Y Level Adjustment (VC-254 board)

Mode
VTR stop
Signal
Measurement Point
No signal
Y signal terminal of S VIDEO OUT
jack (75 terminated)
Adjustment Page
Oscilloscope
C
Adjustment Address
Specified Value
25
A = 1000 20mV
Adjusting method:
Signal
Measurement Point
No signal
Chroma signal terminal of S VIDEO
OUT jack (75 terminated)
External trigger: Y signal terminal of
S VIDEO OUT jack
Adjustment Page
Oscilloscope
C
Adjustment Address
Specified Value
26, 27
Cr level: A = 714 14mV
Cb level: B = 714 14mV
Burst level: C = 286 6mV

Procedure
1
0
01
01 Set the data.
2
11
10
0C
02
25

button.
button.
Adjusting method:
Procedure
1
0
01
01 Set the data.
Change the data and set the Y

value.
Press PAUSE button.
25
0C
00
11
00
01
00

button.
button.
Set the data.
Center of luminance line
11
10
0C
02
26
26
27
7
8
27
0C
00
10
11
00
11
01
00

button.
button.
Change the data and set the Cr
value.
Press PAUSE button.
Change the data and set the Cb
signal level (B) to the specified
value.
Press PAUSE button.
(C) is satisfied the specified
value.
Fig. 5-3-10.

button.
button.
Set the data.
0.28 sec
0.28 sec
Fig. 5-3-11.
5-50
6. Hi8/Standard8 Y/C Output Level Setting

(VC-254 board)
5. VIDEO OUT Y, Chroma Level Check (VC-254 board)

Mode
VTR stop
Signal
Measurement Point
No signal
Video terminal of AUDIO/VIDEO jack
(75 terminated)
Specified Value
Oscilloscope
Sync level: A = 293 18mV
Burst level: B = 286 18mV
Set the Y/C signal output level during the Hi8/Standard8 playback
mode.
Mode
VTR stop
Signal
Adjustment Page
No signal
F
Adjustment Address
67, 68
Note: Perform this adjustment when IC2201 or IC4901 is replaced.
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
11
10
0C
02
Adjusting method:

button.
button.
Check that the sync signal level
(A) satisfies the specified value.
(B) satisfies the specified value.
5
6
0C
00
11
00
01
00

button.
button.
1
2
0
D
01
10
01
02
Set the data.

button.
3
4
6
6
6F
7F
01
Set the data.

Check that the data.
When the data is 00, proceed
to step 8.
When the data is 03, proceed
to step 5.
67
69
68
64

button.
button.
7
8
67
A0
68
AA
10
11
6
D
6F
10
00
00
Set the data.

button.
12
01
00
Set the data.
Set the data.
B
A
H
Fig. 5-3-12.
5-51
Procedure
Proceed to step 10.

button.
button.
7. Hi8/standard 8mm AFC fo Adjustment

(VC-254 board)
Adjust the pull-in range of the clock generator (IC2201) for A/D
conversion during Hi8/standard 8mm playback.
Mode
VTR stop
Signal
Measurement Point
No signal
Pin 2 of CN1108 (AFC f0)
Adjustment Page
Digital voltmeter
F
Adjustment Address
Specified Value
65
A=1.40 0.05Vdc
Or the data of page: 6, address: 6E is
7C to 84
Adjusting method:
Procedure
1
0
01
01 Set the data.
2
10
02

button.
button.
0D
04
4
5
6
6
63
6F
04
01
Set the data.

Set the data.
65
50
01
C5

button.
button.
8
9
6
6
02
01
00
10
6E
11
0D
00
12
63
00
13
14
6
D
6F
10
00
00
Set the data.

button.
15
01
00
Set the data.

button.
Check that the data satisfies the
specifies value.
Or check that the DC voltage
(A) satisfies the specified value.
If outside, repeat steps 6 to 10.
button.
Set the data.
5-52
3-5.
IR TRANSMITTER ADJUSTMENTS
Adjust using the IR receiver jig (J-6082-383-A).

Note: If the distance between the IR receiver jig and the camcorder is
below 1m, cover the LASER LINK emitter with a ND filter. (For
example, when the distance is 30cm to 50cm, cover the LASER
LINK emitter with a ND filter 1.0.)
Switch setting:
SUPER LASER LINK ........................... ON (Red LED is lit)
2. IR Video Deviation Adjustment (VC-254 board)
1. IR Video Carrier Frequency Adjustment

(VC-254 board)
Mode
Signal
VTR stop
Arbitrary
Arbitrary
Pin 5 of CN003 of IR receiver jig (RF)
(Or Pin qh of IC3901 of VC-254 board)
Measurement Point
VIDEO OUT terminal of IR receiver

jig (Terminated at 75)
Oscilloscope
Adjustment Page
Frequency counter
F
Adjustment Page
Adjustment Address
F
7E
Adjustment Address
Specified Value
80
f = 11.85 0.05 MHz
Specified Value
A = 0.82 0.05 V
Mode
VTR stop
Signal
Measurement Point
Connection of Equipment:
Connect the measuring device as shown in the following figure,
and adjust.
and adjust.
IR receiver jig
Pin 5 of
CN003
Main unit
IR receiver jig
Main unit
Frequency counter
75
Oscilloscope
VIDEO
OUT
75 (1-247-804-11)
Fig. 5-3-14.
Fig. 5-3-13.
Adjusting method:
1
2
0
3
01
0C
01
08
80
80
0C
00
01
00
Adjusting method:
Procedure
Set the data.
button.
Change the data, and set the
video carrier frequency (f) to the
specified value.
Press PAUSE button.
button.
Set the data.
1
2
0
3
01
0C
01
01
7E
7E
0C
00
01
00
Procedure
Set the data.
button.
Change the data, set the video
signal amplitude (A) to the
specified value.
Press PAUSE button.
button.
Set the data.
White
Fig. 5-3-15.
5-53
3. IR Audio Deviation Adjustment (VC-254 board)

Mode
VTR stop
Signal
Video : No signal
Audio : 400Hz, 7.5dBs, Audio left
and right terminal of AUDIO/VIDEO
jack
AUDIO L terminal and AUDIO R
terminal of IR receiver jig
(Terminated at 47k)
Measurement Point
Adjustment Page
Audio level meter

F
Adjustment Address
Specified Value
7F
Signal level: 7.5 1.0 dBs
Level difference of L and R: Below
2dB
and adjust.
Main unit
IR receiver jig
Video
(Yellow)
AUDIO/VIDEO
AUDIO OUT
L
R
Audio oscillator
Audio Left
(White)
Attenuator
Audio level meter

Audio Right
(Red)
600
600 : 270 (1-249-410-11) + 330 (1-249-411-11)

47k
47k (1-249-437-11)
Fig. 5-3-16.
Adjusting method:
1
2
01
7F
7F
01

400Hz audio signal level to the
specified value.
Press PAUSE button.
7F
01
Procedure
Set the data.
Connect the audio level meter to
the AUDIO L terminal of the IR
receiver jig.
Connect the audio level meter to

the AUDIO R terminal of the IR
receiver jig.
Check that the 400Hz audio
signal level is within the
specified value. If outside, repeat
from step 2.
00
Set the data.
5-54
3-6.
1. Hi8/Standard8 AFM BPF fo Adjustment

(VC-254 board)
Sets the BPF passing frequency of IC760 so that the AFM signal
can separate from the playback RF signal properly. If deviated. the
mono/stereo mode will be differentiated incorrectly, and noises and
distortions will increase during high volume playback.
Mode
Playback
AUDIO SYSTEM ADJUSTMENTS
[Connecting the measuring instruments for the audio]

Connect the audio system measuring instruments in addition to the
video system measuring instruments as shown in Fig. 5-3-17.
[Adjustment Procedure]
1) Hi8/Standard8 AFM BPF fo adjustment
2) Hi8/Standard8 AFM 1.5MHz deviation adjustment
3) Hi8/Standard8 AFM 1.7MHz deviation adjustment
4) Digital8 playback level check
5) Overall level characteristics check
6) Overall distortion check
7) Overall noise level check
8) Overall separation check
Main unit
Recording (Camera mode)
Audio oscillator
600
Signal
Right
Attenuator
600 : 270 (1-249-410-11) + 330 (1-249-411-11)
Playback
Main unit
TV monitor
Video (Yellow)
Left (White)
AUDIO/
VIDEO
47k
Audio level meter

or Distortion meter
Right
(Red)
Adjustment Page
Distortion meter
F
Adjustment Address
Specified Value
7D
The Main and Sub channel distortion
rate should be almost the same (within
1%) and minimum.
Adjusting method:
2) Set the Hi-Fi SOUND switch (menu display) to 2.
3) Select page: F, address: 7D, change the data and minimize the
distortion rate.
4) Press the PAUSE button.
6) Select page: F, address: 7D, change the data and minimize the
distortion rate.
8) Repeat steps 2) to 7) and set the data of address: 7D so that the
distortions rates when the Hi-Fi SOUND switch is set to 2
and set to 1 respectively are almost the same and minimum.
11) Set the Hi-Fi SOUND switch to STEREO.
MIC
Left
Measurement Point

For BPF adjustment (WR5-11NS)
AUDIO/VIDEO jack left or right
47k
47k (1-249-437-11)
Fig. 5-3-17.
5-55
4. Digital8 Playback Level Check

Mode
Playback
2. Hi8/Standard8 AFM 1.5 MHz Deviation Adjustment

(VC-254 board)
Adjust to the optimum 1.5MHz audio FM signal deviation.
If the adjustment is not correct, its playback level will differ from
that of other units.
Mode
Playback
Signal
Measurement Point

For checking AFM stereo operation
Monoscope section (WR5-9NS)
Adjustment Page
Audio level meter

F
Adjustment Address
Specified Value
7B
7.5 2.0dBs
Signal
Measurement Point
Specified Value
Adjusting method:
3) Select page: F, address: 7B, change the data and set the 400Hz
signal level to the specified value.
5) Set the Hi-Fi SOUND switch (menu display) to STEREO.
Audio level meter and frequency

counter
32 kHz mode: 1 kHz, +3.0 2.0dBs
48 kHz mode: 1 kHz, +3.0 2.0dBs
44.1 kHz mode:
The 7.35kHz signal level during EMP
OFF is +2.0 2.0dBs.
The 7.35kHz signal level during EMP
ON is 6 2 dB from the signal level
during EMP OFF.
Checking Method:
1) Check that the playback signal level is the specified value.
5. Overall Level Characteristics Check
3. Hi8/Standard8 AFM 1.7 MHz Deviation Adjustment

(VC-254 board)
Adjust to the optimum 1.7MHz audio FM signal deviation.
If improper, this causes deteriorated separation (with stereo signal).
Mode
Signal
Digital8 alignment tape:

For audio operation check
(WR5-3ND)
Mode
Signal
Recording and playback

400Hz, 66dBs signal: MIC jack left
and right
Measurement Point

Audio level meter
Specified Value
7.5 3.0dBs
Measurement Point
Playback
For checking AFM stereo operation
Monoscope section (WR5-9NS)
Checking Method:
1) Input the 400Hz, 66dBs signal in the MIC jack left and right.
2) Record the signal.
3) Playback the recorded section.
4) Check that the 400Hz signal level is the specified value.
Adjustment Page
Oscilloscope
F
6. Overall Distortion Check
Adjustment Address
Specified Value
7C
7.5 2.0dBs
Adjusting method:
3) Select page: F, address: 7C, change the data and set the 1kHz
signal level to the specified value.
5) Set the Hi-Fi SOUND switch (menu display) to STEREO.
Mode
Signal

400Hz, 66dBs signal: MIC jack left
and right
Measurement Point

Audio distortion meter
Specified Value
Below 0.4%(200Hz to 6kHz BPF ON)
Checking Method:
1) Input the 400Hz, 66dBs signal in the MIC jack left and right.
4) Check that the distortion is the specified value.
5-56
7. Overall Noise Level Check

Mode
Signal
Measurement Point
No signal: MIC jack left and right

Specified Value
Audio level meter

Below 45dBs
(IHF-A filter ON, 20kHz LPF ON)
8. Overall Separation Check

Mode
Signal
Checking Method:
1) Connect the left terminal of MIC jack and its ground terminal
with a jumper wire.
2) Connect the right terminal of MIC jack and its ground terminal
with a jumper wire.
5) Check that the noise level is the specified value.
6) Remove the jumper wires.
Measurement Point
No signal: MIC jack <left> [right]

400Hz, 66dBs signal: MIC jack
<right> [left]
AUDIO/VIDEO jack <left> [right]
Specified Value
Audio level meter

Below 40dBs
< >: Left channel check

[ ] : Right channel check
Checking Method:
1) Connect the <left> [right] terminal of MIC jack and its ground
terminal with a jumper wire.
2) Input the 400Hz, 66dBs signal in the MIC jack <right> [left].
5) Check that the signal level of the AUDIO/VIDEO jack <left>
[right] is the specified value.
6) Remove the jumper wire.
5-57
5-4. SERVICE MODE

4-1.
ADJUSTMENT REMOTE COMMANDER
2. Precautions Upon Using

the Adjustment Remote Commander
Mishandling of the adjustment remote commander may erase the
correct adjustment data at times. To prevent this, it is recommended
that all adjustment data be noted down before beginning adjustments
and new adjustment data after each adjustment.
The adjustment remote commander is used for changing the

calculation coefficient in signal processing, EVR data, etc. The
adjustment remote commander performs bi-directional
communication with the unit using the remote commander signal
line (LANC). The resultant data of this bi-directional communication
is written in the non-volatile memory.
1. Using the Adjustment Remote Commander
1) Connect the adjustment remote commander to the LANC
terminal.
2) Set the HOLD switch of the adjustment remote commander to
HOLD (SERVICE position). If it has been properly
connected, the LCD on the adjustment remote commander will
display as shown in Fig. 5-4-1.
Page
Data
Address
Fig. 5-4-1.
3)
Operate the adjustment remote commander as follows.

Changing the page
The page increases when the EDIT SEARCH+ button is
pressed, and decreases when the EDIT SEARCH button is
pressed. There are altogether 16 pages, from 0 to F.
Hexadecimal
0 1 2 3 4 5 6 7 8 9 A B CD E F
notation
LCD Display
0 1 2 3 4 5 6 7 8 9 A b c d E F
Decimal notation
conversion value 0 1 2 3 4 5 6 7 8 9 10 1112 1314 15
4)
Changing the address

The address increases when the FF (M) button is pressed,
and decreases when the REW (m) button is pressed. There
are altogether 256 addresses, from 00 to FF.
Changing the data (Data setting)
The data increases when the PLAY (N) button is pressed,
and decreases when the STOP (x) button is pressed. There
are altogether 256 data, from 00 to FF.
Writing the adjustment data
The PAUSE button must be pressed to write the adjustment
data (B, C, D, E, F, 7, 8 page) in the nonvolatile memory.
(The new adjusting data will not be recorded in the
nonvolatile memory if this step is not performed.)
After completing all adjustments, turn off the main power
supply (8.4 V) once.
5-58
4-2.
DATA PROCESS
The calculation of the DDS display and the adjustment remote

commander display data (hexadecimal notation) are required for
obtaining the adjustment data of some adjustment items. In this case,
after converting the hexadecimal notation to decimal notation,
calculate and convert the result to hexadecimal notation, and use it
as the adjustment data. Indicates the hexadecimal-decimal
conversion table.
Hexadecimal-decimal Conversion Table
Lower digit of
hexadecimal
2
4
Upper digit
of hexadecimal
A
(A)
B
(b)
C
(c)
D
(d)
E
(E)
F
( F)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
77
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
A ( A)
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
B (b)
176
179
180
181
182
183
184
185
186
187
188
189
190
191
C (c)
177
193
178
192
194
195
196
197
198
199
200
201
202
203
204
205
206
207
D (d)
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
E (E)
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
F ( F)
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
Note: The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander.
(Example) If the DDS display or the adjustment remote commander shows BD (bd);
Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point
189 of 1 and 2 in the above table is the corresponding decimal number.
Table. 5-4-1.
5-59
4-3.
2. Emergence Memory Address
SERVICE MODE
2-1. C Page Emergence Memory Address

Page C
Address F4 to FF
Additional note on adjustment

Note: After the completion of the all adjustments, cancel the service mode
by either of the following ways.
1) After data on page: D and F is restored, unplug the main power
supply and remove the coin lithium battery. ( In this case, date
and time and menu setting have been set by users are canceled.
Perform resetting.)
2) After data on page: D and F is restored, select page: 0, address:
01, and return the data to 00. And when data on page:2 and 3 are
changed, return data to the original condition.
Address
Contents
F4
EMG code when first error occurs
F6
F7
1. Setting the Test Mode
Page F
Data
80
81
Address 22
F8
FA
EMG code when second error occurs

Upper: MSW code when shift starts when second
error occurs
Lower: MSW code when second error occurs
FB
Lower: MSW code to be moved when second error

occurs
EMG code when last error occurs
Function
Normal
Test mode
Various emergency prohibitions and releases
Drum emergency, capstan emergency, loading motor
emergency, reel emergency, tape top and end, DEW
detection
FC
FE
FF
Page D
Data
00
01
02
Address 10
Upper: MSW code when shift starts when first error

occurs
Lower: MSW code when first error occurs
Lower: MSW code to be moved when first error
occurs
Upper: MSW code when shift starts when last error

occurs
Lower: MSW code when last error occurs
Lower: MSW code to be moved when last error
occurs
When no error occurs in this unit, data 00 is written in the above

addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency address
(F4 to F7). In the same way, when the second error occurs, the data
corresponding to the error is written in the second emergency address
(F8 to FB).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (FC to FF).
Function
Normal
Forced camera power ON
Forced VTR power ON
Before setting the data , select page: 0, address: 01, and set data:
01.
For page D and F, the data set will be recorded in the non-volatile
memory by pressing the PAUSE button of the adjustment remote
commander. In this case, take note that the test mode will not be
exited even when the main power is turned off (8.4Vdc).
After completing adjustments/repairs, be sure to return the data
of page: D address: 10 to 00, and the data of page: F address: 22
to 80, and press the PAUSE button of the adjustment remote
commander. And select page: 0, address: 01, and set data: 00.
Note : After completing adjustments, be sure to initialize the data of

addresses F4 to FF to 00.
Initializing method:
2) Select page: 3, address: 01, set data: 37, and press the PAUSE
button.
5-60
2-2. F Page Emergence Memory Address
2-3. EMG Code (Emergency Code)

Codes corresponding to the errors which occur are written in C
page, addresses F4, F8 and FC (or F page, addresses 10, 14 and 18).
The type of error indicated by the code are shown in the following
table.
Code
Emergency Type
Note 1: Emergence of PB mode only.
Page F
Address 10 to 1B
Address
Contents
10
EMG code when first error occurs
12
13
Upper: MSW code when shift starts when first error

occurs
Lower: MSW code when first error occurs
Lower: MSW code to be moved when first error
occurs
14
16
EMG code when second error occurs

Upper: MSW code when shift starts when second
error occurs
Lower: MSW code when second error occurs
17
Lower: MSW code to be moved when second error

occurs
EMG code when last error occurs
18
1A
1B
00
10
No error
Loading motor emergency during loading
11
22
Loading motor emergency during unloading

T reel emergency during normal rotation
23
S reel emergency during normal rotation

T reel emergency (Short circuit between S reel
24
Upper: MSW code when shift starts when last error

occurs
Lower: MSW code when last error occurs
Lower: MSW code to be moved when last error
occurs
When no error occurs in this unit, data 00 is written in the above

addresses (10 to 1B). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency address
(10 to 13). In the same way, when the second error occurs, the data
corresponding to the error is written in the second emergency address
(14 to 17).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (18 to 1B).
Note 2: After completing adjustments, be sure to initialize the data of
addresses 10 to 1B to 00.
button.
3) Select address: 11 to 1B and set data 00 into them in the
same way as in address: 10.
5-61
30
terminal and T reel terminal)

FG emergency at the start up of the capstan
40
42
FG emergency at the start up of the drum

FG emergency during normal rotation of the drum
2-4. MSW Code

The lower parts of the data of C page, addresses F6, FA and FE
(or F page, addresses 12, 16 and 1A) represent the MSW codes
(mode switch mechanism position) when errors occurs.
The upper parts of the data of C page, addresses F6, FA and FE
(or F page, addresses 12, 16 and 1A) represent, when the
mechanism position is to be moved, the MSW codes at the start
movement (when moving the loading motor).
The lower parts of the data of C page, addresses F7, FB and FF
(or F page, addresses 13, 17 and 1B) represent the MSW codes
of the desired movement when the mechanism position is to be
moved.
Unloading
Mechanism position
BL STOP BL
TURN
BL
REC/PB
BL
REW
0 1 0 1 = 5
0 1 1 1 = 7
0 0 0 0 = 0
0 1 1 1 = 7
0 1 0 0 = 4
0 1 1 1 = 7
0 1 1 0 = 6
MODE SW A
Loading
LOAD
0 1 1 1 = 7
0 0 1 0 = 2
MODE SW B
BL
0 1 1 1 = 7
0 0 1 1 = 3
MODE SW C
USE
BL
0 1 1 1 = 7
0 0 0 1 = 1
MSB
EJECT
LS chassis movement range

Pinch roller is detached
Pinch roller is pressed
Releasing lock of
cassette campartment
Mechanism Position MSW Code

EJECT
BL
USE
LOAD
STOP
TURN
REC/PB
REW
Contents
Position at which the cassette compartment lock is released. The mechanism will not move any
further in the unloading direction.
BLANC code. Between two codes. The mechanism will not be stopped by this code while it is
operating.
EJECT completion position. When the cassette is ejected, the mechanism will stop at this
position.
Code during loading/unloading. Code that is used while the LS chassis is moving.
Normal stop position. The pinch roller separates, the tension regulator returns, and the brakes of
both reels turn on.
Position at which is used when the pendulum gear swings from S to T or from T to S.
PB, REC, CUE, REV, PAUSE, FF positions.
The pinch roller is pressed and tension regulator is on.
REW position. REW are carried at this position.
The mechanism will not move any further in the loading direction.
5-62
3. Bit Value Discrimination

Bit values must be discriminated using the display data of the
adjustment remote commander for the following items. Us the table
below to discriminate if the bit value is 1 or 0.
Display on the
adjustment
remote
commander
0
1
2
3
4
5
6
7
A
8
9
A (A)
B (b)
C (C)
D (d)
E (E)
B
F (F )
Display on the adjustment remote commander
Address
Page
bit3 to bit0 discrimination

bit7 to bit4 discrimination
(Example)
If the remote commander display is 8E, bit value from bit

7 to bit 4 can be discriminated from the column A, and
those from bit 3 to bit 0 from column B.
4. Switch check (1)

Page 2
Bit
0
1
2
3
4
5
6
7
bit3
or
bit7
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Bit values
bit2
bit1
or
or
bit6
bit5
0
0
0
0
0
1
0
1
1
0
1
0
1
1
1
1
0
0
0
0
0
1
0
1
1
0
1
0
1
1
1
1
Address 43
Function
POWER SW (VTR MODE SW) (SS-1380 block)
POWER SW (CAM MODE SW) (SS-1380 block)
START/STOP SW (SS-1380 block)
EJECT SW (SS-1380 block)
CC DOWN SW (Mechanism chassis)
PHOTO FREEZE SW (SS-1380 block)
POWER SW (PHOTO STBY SW) (SS-1380 block) *1
When bit value = 1

OFF
OFF
OFF
OFF
OFF (UP)
OFF
OFF
When bit value = 0

ON (VCR/PLAYER)
ON (CANERA)
ON
ON
ON (DOWN)
ON
ON (MEMORY)
Using method:
1) Select page: 2, address: 43.
2) By discriminating the bit value of display data, the state of the switch can be discriminated.
5. Switch check (2)
Page 2
Bit
4
5
6
7
Address 49
Function
MIC jack (FP-273 flexible)
When bit value = 1

Used
When bit value = 0

Not used
AUDIO/VIDEO jack (FP-270 flexible J102)

S VIDEO jack (FP-270 flexible J101)
Used
Not used
Not used
Used
Using method:
1) Select page: 2, address: 49.
6. Switch check (3)
Page 3
Bit
6
Address 5A
Function
HEADPHONES jack (FP-273 flexible)
When bit value = 1

Used
When bit value = 0

Not used
Using method:
1) Select page: 3, address: 5A.
5-63
bit0
or
bit4
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
7. Switch check (4)

Page 2
Address 60 to 65
Using method:
1) Select page: 2, address: 60 to 65.
2) By discriminating the display data, the pressed key can be discriminated.
Data
00 to 0C
0D to 24
25 to 3F
40 to 5D
5E to 81
82 to AA
AB to D7
D8 to FF
60
EDIT SEARCH + EDIT SEARCH
SUPER
STOP
FF
REC
(KEY AD0) (CF-079/080) (CF-079/080) LASER LINK
No key input
(FP-275)
(FP-275)
(FP-275)
(IC4803 od)
(S117)
(S116)
(FP-275)
61
PHOTO
PAUSE
REW
PLAY
(KEY AD1)
(PHOTO START)
No key input
(FP-275)
(FP-275)
(FP-275)
(SS-1380)
(IC4803 of)
62
MENU
MENU
TITLE
VOLUME + VOLUME BACKLIGHT
EXPOSURE
(KEY AD2) (CF-079/080)
EXECUTE (CF-079/080) (CF-079/080) (CF-079/080) (CF-079/080) No key input
(SE-1380)
(IC4803 og)
(S102)
(SE-1380)
(S108)
(S111)
(S113)
(S115)
63
MEMORY + MEMORY MEMORY INDEX MEMORY DELETE MEMORY PLAY MEMORY MIX
(KEY AD3) (CF-079/080) (CF-079/080) (CF-079/080) (CF-079/080) (CF-079/080) (CF-079/080) PANEL CLOSE PANEL OPEN
(S106)*1
(S109)*1
(S112)*1
(S114)*1
(IC4803 oh) (S103)*1
(S104)*1
64
SUPER
END SEARCH DISPLAY
PB ZOOM
FADER
FOCUS
FOCUS AUTO
(KEY AD4)
NIGHT SHOT (CF-079/080) (CF-079/080) (CF-079/080) (CF-079/080)
MANUAL
(FP-282)
(IC4803 oj)
(FP-275)
(S105)
(S107)
(S110)
(S118)
(FP-282)
65
PANEL
PANEL
(KEY AD5)
REVERSE
NORMAL
(IC4803 ok)
(FP-283)
(FP-283)
Address
8. Record of Use check
Note: When replacing the drum assembly, initialize the data of address: A2 to A4.
Page 2
Bit
A2
A3
A4
A5
A6
A7
A8
A9
AA
Address A2 to AA
Function
Drum rotation
counted time
(BCD code)
User initial power
on date
(BCD code)
Final condensation
occurrence date
(BCD code)
Remarks
Minute
Hour (L)
Hour (H)
Year
Month
Day
Year
Month
Day
10th place digit and 1st place digit of counted time (decimal digit)
1000th place digit and 100th place digit of counted time (decimal digit)
After setting the clock, set the date of power on next
Using method:
1) The record of use data is displayed at page: 2, addresses: A2 to AA.
Note: This data will be erased (reset) when the CF-079/080 board (VC-254 board CN1117 (45P)) is removed.
1) Using the adjustment remote commander, select the object address and set data: 00.
5-64
9. Record of Self-diagnosis check

Page 2
Address B0 to C6
Address
B0
B1
B2
B4
B5
B6
B8
B9
BA
BC
BD
BE
C0
C1
C2
C4
C5
C6
Self-diagnosis code
Repaired by code (Occurred 1st time) *1
Block function code (Occurred 1st time)
Detailed code (Occurred 1st time)
Repaired by code (Occurred 2nd time) *1
Block function code (Occurred 2nd time)
Detailed code (Occurred 2nd time)
Repaired by code (Occurred 3rd time) *1
Block function code (Occurred 3rd time)
Detailed code (Occurred 3rd time)
Repaired by code (Occurred 4th time) *1
Block function code (Occurred 4th time)
Detailed code (Occurred 4th time)
Repaired by code (Occurred 5th time) *1
Block function code (Occurred 5th time)
Detailed code (Occurred 5th time)
Repaired by code (Occurred the last time) *1
Block function code (Occurred the last time)
Detailed code (Occurred the last time)
*1 : 01 t C, 03 t E
Using method:
1) The past self-diagnosis codes are displayed at page: 2, addresses: BC to C6. Refer to SELF-DIAGNOSIS FUNCTION for detail of the
self-diagnosis code.
Note: This data will be erased (reset) when the CF-079/080 board (VC-254 board CN1117 (45P)) is removed.
5-65E
SECTION 6
REPAIR PARTS LIST
6-1. EXPLODED VIEWS

NOTE:
-XX, -X mean standardized parts, so they may
have some differences from the original one.
Items marked * are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
The mechanical parts with no reference number
in the exploded views are not supplied.
Abbreviation
HK
: Hong Kong model
KR
: Korea model
JE
: Tourist model
BR
: Brazilian model
AR
: Argentina model
The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifis par une marque
0 sont critiques pour la scurit.
Ne les remplacer que par une pice portant
le numro spcifi.
6-1-1. OVERALL SECTION

3
12
3
13
Cabinet (R) section

(See page 6-4 (TRV230/TRV330),
6-5 (TRV530))
3
14
11
SO
NY
15
C
6
3
17
5
4
not
supplied
7
3
B
A
l8
ita
Dig
18
18
16
10
not supplied
(TRV230/TRV330)
(TRV530)
MIC901
Ref. No.
MIC902
Part No.
Description
Remarks
1
2
3
4
5
X-3951-161-1
3-065-310-01
3-067-347-01
X-3949-376-1
X-3951-160-1
GRILLE ASSY, MICROPHONE

RING, RUBBER
MI SCREW M2 (H)
CAP (N) ASSY, LENS
PANEL ASSY, FRONT
6
7
8
8
9
3-066-722-01 CUSHION, SENSOR

3-948-339-61 TAPPING
A-7074-645-A SI-028 (T) BOARD, COMPLETE
(TRV230/TRV330)
A-7074-673-A SI-029 (T) BOARD, COMPLETE (TRV530)
A-7074-651-A FP-273 BOARD, COMPLETE
10
3-065-327-01 CUSHION (MI)
Ref. No.
Part No.
Description
11
12
13
14
15
3-742-854-01
1-475-141-61
3-065-326-01
3-065-325-01
3-065-567-01
LID, BATTERY (FOR RMT-814)

REMOTE COMMANDER (RMT-814)
CABINET (UPPER)
LID (BT), CPC
TAPPING (M1.7)
16
17
18
18
18
3-065-366-01
3-066-720-01
X-3951-258-1
X-3951-260-1
X-3951-264-1
WINDOW (2), LCD

CUSHION (SI)
COVER (138) ASSY, CPC (TRV230)
MIC901 1-542-312-11 MICROPHONE (Rch)

MIC902 1-542-312-11 MICROPHONE (Lch)
6-1
Remarks
6-1-2. CABINET (L) SECTION-1

74
Cabinet (L) section-2

(See page 6-3)
65
65
65
57
55
54
C
56
F
E G
D
Mechanism deck
(See page 6-9 to 6-12)
G
H
4
-25
VCard
o
BB
65
F
E
D
65
69
(TRV330/TRV530)
71
58
CN910
65
65
53
68
65
67
62
73
65
B
65
61
65
63
72
65
64
Lens section
(See page 6-8)
51
52
53
54
54
55
56
Part No.
Description
65
Remarks
Part No.
Description
60
61
62
63
64
3-948-339-61
A-7074-650-A
1-680-121-11
A-7074-648-A
A-7074-649-A
TAPPING
FP-272 BOARD, COMPLETE
FP-271 BOARD, COMPLETE (TRV330/TRV530)
65
66
67
68
* 69
4-974-725-01
A-7074-647-A
1-500-226-11
3-066-169-01
X-3951-170-1
SCREW (M1.7X2.5), P
PC-082 BOARD, COMPLETE (TRV330/TRV530)
BEAD, FERRITE (TRV330/TRV530)
SHEET, MD
SHIELD ASSY, DD
70
71
72
73
74
3-941-343-21
3-066-759-01
3-066-707-01
3-065-662-01
3-065-567-01
TAPE (A)
SHEET, VC
SHEET (T), ELECTROSTATIC (TRV530)
LABEL, LS CAUTION
TAPPING (M1.7), P
CN910
1-815-123-11 CONNECTOR, MEMORY STICK

(TRV330/TRV530)
CUSHION, LENS
FRAME, MD
CONNECTOR, EXTERNAL (HOT SHOE)
(TRV330/TRV530)
1-815-124-21 CONNECTOR, EXTERNAL (HOT SHOE)(TRV230)
57
57
57
58
59
A-7074-672-A
A-7074-687-A
3-065-397-01
1-680-134-11
56
Ref. No.
3-066-721-01
1-680-119-11
3-065-372-01
1-815-124-11
1-680-118-11 FP-264 FLEXIBLE BOARD

A-7096-436-A VC-254 (BNA) BOARD, COMPLETE (SERVICE)
(TRV230)
A-7096-438-A VC-254 (BFNA) BOARD, COMPLETE (SERVICE)
(TRV330)
A-7096-439-A VC-254 (BFNS) BOARD, COMPLETE (SERVICE)
(TRV530)
A-7074-644-A FU-150 (NF) BOARD, COMPLETE (TRV330)
56
2
-08
PCard
o
B
(TRV530)
65
Ref. No.
60
66
C
52 70
51
59
FU-154 (NF) BOARD, COMPLETE (TRV530)

FU-150 (N) BOARD, COMPLETE (TRV230)
HOLDER, MS
FP-274 FLEXIBLE BOARD (TRV330/TRV530)
6-2
Remarks

110
107
103
112
BT901
103
104
103
109
108
A
102
106
not
not
supplied
105 supplied
111
101
103
A
Ref. No.
Part No.
Description
101
102
103
104
105
X-3951-159-1
3-052-815-01
3-067-347-01
3-065-308-01
3-978-765-01
CABINET (L) ASSY

BELT (ES), GRIP
MI SCREW M2 (H)
LABEL (L)
SLIDER, G LOCK
106
107
3-713-791-01 SCREW (M1.7X4), TAPPING, P2

1-476-415-11 SWITCH BLOCK, CONTROL (SS-1380)
(TRV330/TRV530)
1-476-415-21 SWITCH BLOCK, CONTROL (SS-1380)(TRV230)
107
Remarks
Ref. No.
Part No.
108
* 109
110
110
111
X-3951-158-1 FRAME ASSY, CS

3-065-324-01 SHEET METAL (LOWER), STRAP
X-3951-157-1 PANEL ASSY, BATTERY
(TRV230/TRV330:US,CND,E,HK,KR,JE/TRV530)
X-3951-472-1 PANEL (B) ASSY, BATTERY (TRV330:BR)
3-065-567-01 TAPPING (M1.7)
112
BT901
4-974-725-01 SCREW (M1.7X2.5), P

1-694-772-11 TERMINAL BOARD, BATTERY
6-3
Description
Remarks
6-1-4. CABINET (R) SECTION (2.5 INCH LCD MODEL)(TRV230/TRV330)

158
159
161
EVF section
(See page 6-8)
153
SP901
E
F
153
160
153
157
164
153
156
155
E
152
not
supplied
163
LCD section
(See page 6-6
(2.5 inch LCD model))
165
171 170
153
169
CF
Bo -079
ard
154
F
A
166
153
153
162
151
172
167
168
153
S910
153
: BT101 (Lithium battary) CF-079 board on the mount position. (See page 4-67)
Ref. No.
Part No.
Description
151
152
152
153
154
1-791-948-11
A-7074-675-A
A-7074-686-A
3-948-339-61
1-476-416-11
CABLE, FLEXIBLE FLAT (FFC-001)

CF-079 (SBF) BOARD, COMPLETE (TRV330)
CF-079 (SB) BOARD, COMPLETE (TRV230)
TAPPING
SWITCH BLOCK, CONTROL (SE-1380)
Remarks
* 155
* 156
* 157
158
159
3-065-398-01
3-058-658-01
3-065-385-01
X-3951-173-1
A-7074-652-A
RETAINER, SPEAKER
SPACER (101), SPEAKER
HOLDER, VTR
BUTTON ASSY, VTR
160
161
162
163
A-7074-653-A
X-3951-174-1
3-067-347-01
3-969-387-01

COVER (140) ASSY, HINGE
MI SCREW M2 (H)
FOOT, RUBBER
Ref. No.
Part No.
Description
164
164
165
165
166
X-3951-171-1
X-3951-172-1
3-065-353-01
3-065-353-11
3-065-352-01
CABINET R (140) ASSY(TRV330)

CABINET R (138) ASSY(TRV230)
COVER (B), JACK (TRV330)
COVER (B), JACK (TRV230)
COVER (F), JACK
167
168
* 169
170
171
3-065-386-01
3-065-373-01
3-065-521-01
3-066-939-01
3-066-940-01
RETAINER, TRIPOD
SCREW (Y), TRIPOD
SHEET, MUFFLE
SHEET, CF ELECTROSTATIC
SHEET (2), CF ELECTROSTATIC
172
SP901
S910
6-4
3-066-943-01 SHEET (R), B

1-529-590-11 SPEAKER (2.0CM)
1-771-848-11 SWITCH, PUSH
Remarks
6-1-5. CABINET (R) SECTION (3.5 INCH LCD MODEL)(TRV530)

LCD section
(See page 6-7
(3.5 inch LCD model))
208
209
EVF section
(See page 6-8)
203
203
SP901
F
203
207
203
206
205
223
not
supplied
203
213
211
215
221
220
202
B
CF
Bo -080
ard
219
204
216
203
214
203
222
210
224
203
212
201
217
203
218
S910
203
: BT101 (Lithium battary) CF-080 board on the mount position. (See page 4-71)
Ref. No.
Part No.
Description
Part No.
Description
201
202
203
204
205
1-791-948-11
A-7074-677-A
3-948-339-61
1-476-416-11
3-065-398-01
CABLE, FLEXIBLE FLAT (FFC-001)

CF-080 (SBF) BOARD, COMPLETE
TAPPING
SWITCH BLOCK, CONTROL (SE-1380)
RETAINER, SPEAKER
Remarks
Ref. No.
214
215
216
217
218
X-3951-175-1
3-065-353-01
3-065-352-01
3-065-386-01
3-065-373-01
CABINET R (148) ASSY

COVER (B), JACK
COVER (F), JACK
RETAINER, TRIPOD
SCREW (Y), TRIPOD
206
207
208
209
210
3-058-658-01
3-065-385-01
X-3951-173-1
A-7074-652-A
A-7074-653-A
SPACER (101), SPEAKER

HOLDER, VTR
BUTTON ASSY, VTR
219
220
221
222
223
3-065-521-01
3-066-939-01
3-066-941-01
3-066-943-01
3-067-601-01
SHEET, MUFFLE
SHEET, CF ELECTROSTATIC
SHEET (3), CF ELECTROSTATIC
SHEET (R), B
CF ELECTROSTATIC SHEET (4)
211
212
213
X-3951-176-1 COVER (148) ASSY, HINGE

3-067-347-01 MI SCREW M2 (H)
3-969-387-01 FOOT, RUBBER
224
SP901
S910
3-941-343-21 TAPE (A)

1-529-590-11 SPEAKER (2.0CM)
1-771-848-11 SWITCH, PUSH
6-5
Remarks
6-1-6. LCD SECTION (2.5 INCH LCD MODEL)(TRV230/TRV330)
259
260
261
262
257
266
263
A
ND901
258
265
LCD901
264
PD
Bo -13
ard 8
256
254
A
253
B
D902
252
251
Ref. No.
255
Part No.
Description
251
252
253
254
255
3-065-364-01
3-067-347-01
3-989-735-51
A-7096-434-A
3-065-368-01
CABINET C (2), P
MI SCREW M2 (H)
SCREW (M1.7), LOCK ACE, P2
INDICATION LCD BLOCK ASSY (SERVICE)
HOLDER (2), LCD
Remarks
256
257
258
259
260
A-7074-646-A
3-065-567-01
3-065-395-01
4-974-725-01
A-7074-654-A
PD-138 (XS6) BOARD, COMPLETE

TAPPING (M1.7)
COVER C (2.5), HINGE
SCREW (M1.7X2.5), P
Ref. No.
261
262
263
264
265
266
0 ND901
0 D902
LCD901
6-6
Part No.
Description
X-3951-181-1
3-065-394-01
1-960-973-21
3-318-203-11
3-065-367-01
HINGE ASSY
COVER (M), HINGE
HARNESS (VP-076)
SCREW (B1.7X6), TAPPING
FRAME (2), P
X-3951-177-1
1-518-725-21
1-518-721-11
1-803-852-21
CABINET M (2) ASSY, P

TUBE, FLUORESCENT,COLD CATHODE
LIGHT, BACK
INDICATOR MODULE LIQUID CRYST
Note :
specified.
Remarks
Note :
pour la scurit.
6-1-7. LCD SECTION (3.5 INCH LCD MODEL)(TRV530)

309
306
310
303
311
315
312
C
A
313
ND901
B
314
308 306
LCD901
307
PD
Bo -13
ard 9
304
302
A
301
306 305
D902
B
303
Ref. No.
Part No.
Description
301
302
303
304
* 305
X-3951-180-1
A-7096-435-A
3-067-347-01
3-989-735-61
3-065-392-01
CABINET C (3) ASSY, P

INDICATION LCD BLOCK ASSY (SERVICE)
MI SCREW M2 (H)
SCREW (M1.7), LOCK ACE, P2
HOLDER (3), LCD
Remarks
306
307
308
309
4-974-725-01
A-7074-674-A
3-065-396-01
3-065-567-01
SCREW (M1.7X2.5), P
PD-139 (Z12) BOARD, COMPLETE
COVER C (3), HINGE
TAPPING (M1.7)
Ref. No.
310
311
312
313
314
315
0 ND901
0 D902
LCD901
6-7
Part No.
Description
A-7074-654-A
X-3951-181-1
3-065-394-01
1-960-973-21
3-065-391-01

HINGE ASSY
COVER (M), HINGE
HARNESS (VP-076)
FRAME (3), P
X-3951-179-1
1-517-855-31
1-518-721-11
8-753-051-00
CABINET M (3) ASSY, P

TUBE, FLUORESCENT, COLD CATHODE
LIGHT, BACK
ACX310AK-J (SERVICE)
Note :
specified.
Remarks
Note :
pour la scurit.
6-1-8. LENS, EVF SECTION

373
371
353
354
370
354
369
352
LCD903
367
358
IC501
365
363
355
354
357
M904
368
362
372
366
356
364
not
supplied
360
351
M905
361
354
359
360
Be sure to read Precautions upon replacing CCD imager

on page 4-10 when changing the CCD imager.
Ref. No.
Part No.
Description
351
352
353
354
355
8-848-740-01
X-3951-248-1
3-065-022-01
3-713-791-41
1-758-554-11
DEVICE, LENS LSV-700A

IRIS FLEXIBLE, ASSY
TAPPING (B1.7X3.5), HEAD
SCREW, TAPPING (M1.7X5), P2
FILTER BLOCK, OPTICAL
356
357
357
358
359
3-053-973-01
A-7074-642-A
A-7074-670-A
3-318-203-11
3-065-057-01
360
361
362
363
3-065-567-01
X-3951-165-1
1-680-123-11
A-7074-676-A
Remarks
Ref. No.
Part No.
Description
363
364
365
366
367
A-7074-678-A
3-065-058-01
3-065-059-01
3-065-061-01
3-065-060-01
LB-070 (SB) BOARD, COMPLETE (TRV530)

GUIDE, LAMP
ILLUMINATOR (1)
SHEET (2) (138), PRISM
SHEET (1) (138), PRISM
RUBBER (W), SEAL

CD-292 BOARD, COMPLETE (TRV230/TRV330)
CD-315 BOARD, COMPLETE (TRV530)
SCREW (B1.7X6), TAPPING
GUIDE (2), FLEXIBLE
368
* 369
370
371
372
3-065-062-01
3-058-232-01
X-3951-168-1
X-3951-163-1
X-3951-167-1
CUSHION (138), LCD

CUSHION (1) (97), LCD
LENS (B) ASSY, VF
CABINET (UPPER) ASSY, EVF
CABINET (LOWER) ASSY, EVF
TAPPING (M1.7)
HINGE ASSY, VF
LB-068 (SB) BOARD, COMPLETE
(TRV230/TRV330)
* 373
LCD903
IC501
M904
M905
3-065-376-01
8-753-028-49
A-7031-213-A
1-763-634-11
1-763-635-11
LABEL (138), B
LCX032AP-J (SERVICE)
CCD BLOCK ASSY (CCD IMAGER)
MOTOR STEPPING Z700 (ZOOM)
MOTOR STEPPING F700 (FOCUS)
6-8
Remarks
6-1-9. CASSETTE COMPARTMENT ASSY, DRUM ASSY

701
702
701
703
705
706
708
LS chassis block
assembly
(See page 6-10)
M901
704
707
709
Mechanical chassis block

assembly
(See page 6-11 to 6-12)
710
Ref. No.
Part No.
Description
701
702
703
704
705
3-065-932-01
3-065-895-01
3-065-896-01
X-3951-298-1
X-3951-302-1
PAN (2 MAIN M1.4X1.6), CAMERA

LEVER, REEL RELEASE
PLATE, BLIND
CASSETTE COMPARTMENT ASSY
DAMPER ASSY
706
X-3951-297-1 GEAR ASSY, R DRIVE
Remarks
Ref. No.
707
708
709
710
M901
6-9
Part No.
Description
3-065-840-01
3-065-935-01
3-947-503-01
X-3951-299-1
A-7048-951-A
CUT (0.98X3X0.13), LUMILER (W)

HLC CUT 1.8X4X0.5
SCREW (M1.4)
SCREW ASSY, DRUM FITTING
DRUM (DKH-04A-R)(SERVICE)
Remarks
6-1-10. LS CHASSIS BLOCK ASSEMBLY

759
757
760
767
S001
764
766
758
768
763
769
765
770
761
762
756
771
755
772
781
752
S002
not supplied
Q001
775
778
780
776
H001
779
774
D001
LS-057
not supplied
H002
FP-301
not supplied
FP-300
not supplied
777
Q002
773
FP-302
not supplied
not
supplied
754
753
752
783
751
782
Ref. No.
Part No.
Description
Part No.
Description
751
752
753
754
755
3-065-822-01
3-947-503-01
A-7096-416-A
A-7096-415-A
A-7096-426-A
RAIL (S), GUIDE

SCREW (M1.4)
BASE (S) BLOCK ASSY, GUIDE
BASE (T) BLOCK ASSY, GUIDE
CHASSIS ASSY, LS
Remarks
Ref. No.
771
772
773
774
775
3-065-830-01
X-3951-288-1
3-065-819-01
3-065-821-01
X-3951-289-1
SPRING, S RATCHET
TABLE (T) ASSY, REEL
SPRING, TG1 ARM
RAIL (T), GUIDE
TABLE (S) ASSY, REEL
756
757
758
759
760
3-065-802-01
A-7096-414-A
3-065-801-01
3-065-932-01
X-3951-303-1
SPRING, TG7 ARM

ARM BLOCK ASSY, TRG7
RETAINER, TG7
ARM ASSY, PINCH
776
777
778
779
780
3-065-833-01
3-065-831-01
X-3951-304-1
3-065-835-01
3-065-820-01
GUIDE, LOCK
PLATE (SPR), RE RETURN
ARM ASSY, TG1
GUIDE (S), CASSETTE
SPRING, RVS ARM
761
762
763
764
765
3-065-823-01
3-065-794-01
3-065-792-01
3-065-834-01
3-065-824-01
ARM, T RATCHET
ROAD (SPR), PINCH ARM
ROLLER, P LIM ARM
GUIDE (T), CASSETTE
SPRING, T RATCHET
781
782
783
S001
H001
X-3951-296-1
3-065-836-01
3-067-167-01
1-692-614-11
8-719-033-37
BAND ASSY, BT
COVER, LS GREASE
SCREW (M1.4X2), CAMERA TAPPING
SWITCH, PUSH (3KEY) (REC PROOF)
ELEMENT, HALL HW-105C (T REEL)
766
767
768
769
770
A-7096-417-A
7-627-852-38
3-065-832-01
3-065-828-01
3-065-829-01
SOFT ASSY, T
SCREW, PRECISION +P1.7X1.8 TYPE3
PLATE, LS CAM
ARM, S RATCHET
PLATE, S RATCHET (RE)
H002
D001
Q001
Q002
8-719-033-37
8-719-988-42
8-729-907-25
8-729-907-25
ELEMENT, HALL HW-105C (S REEL)

DIODE GL453 (TAPE LED)
PHOTO TRANSISTOR PT4850F (TAPE TOP)
PHOTO TRANSISTOR PT4850F (TAPE END)
6-10
Remarks
6-1-11. MECHANICAL CHASSIS BLOCK ASSEMBLY-1

816
811
805
815
819
824
809
817
805
815
810
not
supplied
814
802
807
813
M902
812
815
802
821
820
M903
822
806
823
802
808
818
804
803
Mechanical chassis
block assembly-2
(See page 6-12)
801
Ref. No.
Part No.
Description
Part No.
Description
801
802
803
804
805
A-7096-422-A
3-947-503-01
3-065-928-01
3-065-927-01
3-065-932-01
BASE ASSY, DRUM

SCREW (M1.4)
SPACER, GROUND
GROUND, DRUM
Remarks
Ref. No.
814
815
816
817
818
3-065-881-01
3-065-934-01
1-786-096-11
3-065-898-01
3-065-870-01
SPRING, P PRESSURE PLATE

HLW CUT 0.98X3X0.25
SWITCH, ROTALY
SPRING, EJECT ARM
ROLLER, LS GUIDE
806
807
808
809
810
3-067-154-01
3-065-931-01
X-3947-398-1
3-065-933-01
1-677-049-11
SPRING, CAPSTAN
RAIL (T2), GUIDE
SCREW ASSY, M1.7 PW
PAN (2 MAIN 1.4X4.5), CAMERA
FP-228 FLEXIBLE BOARD (DEW SENSOR)
819
820
821
822
823
A-7096-421-A
3-065-918-01
A-7096-419-A
3-065-902-01
3-065-905-01
ARM ASSY, HCL

GEAR (2), CAM RELAY
GEAR ASSY, CHANGE
BELT, TIMING
GEAR, RELAY
811
812
813
1-680-434-11 FP-299 FLEXIBLE BOARD

3-065-877-01 PLATE (T), GUIDE LOCK
X-3951-301-1 PLATE ASSY, PINCH PRESSURE
824
M902
M903
3-065-882-01 ARM, EJECT

8-835-701-01 MOTOR, DC SCE13A/C-NP (CAPSTAN)
A-7096-420-A MOTOR ASSY, LD (LOADING)
6-11
Remarks
6-1-12. MECHANICAL CHASSIS BLOCK ASSEMBLY-2

860
863
861
859
857
862
864
858
865
856
855
853
866
854
852
851
867
868
Ref. No.
Part No.
Description
Part No.
Description
851
852
853
854
855
3-065-920-01
3-065-913-01
3-065-914-01
3-065-917-01
3-065-934-01
ARM, HC DRIVE
GEAR (4), LD
SHEET, COVER
GEAR (1), CAM RELAY
HLW CUT 0.98X3X0.25
Remarks
Ref. No.
860
861
862
863
864
7-624-101-04
A-7096-412-A
X-3951-307-1
X-3951-305-1
3-065-901-01
STOP RING 1.2 (E TYPE)

GEAR (T) ASSY, GUIDE
PLATE ASSY, M SLIDE
ARM ASSY, LS
ROLLER, LS ARM
856
857
858
859
3-065-915-01
3-065-878-01
3-065-932-01
A-7096-413-A
GEAR (1), CAM

PLATE (S), GUIDE LOCK
GEAR (S) ASSY, GUIDE
865
866
867
868
3-065-916-01
3-065-919-01
X-3951-308-1
X-3951-300-1
GEAR (2), CAM

ARM, T1 LIMITTER
ARM ASSY, GL
CHASSIS ASSY, MECHANICAL
6-12
Remarks
CD-292
CD-315
CF-079
CF-080
6-2. ELECTRICAL PARTS LIST

NOTE:
Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
-XX, -X mean standardized parts, so they may
have some difference from the original one.
Items marked * are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
CAPACITORS:
uF: F
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
Ref. No.
Part No.
COILS
uH: H
SEMICONDUCTORS
In each case, u: , for example:
uA...: A... , uPA... , PA... ,
uPB... , PB... , uPC... , PC... ,
uPD..., PD...
Abbreviation
HK
: Hong Kong model
KR
: Korea model
JE
: Tourist model
BR
: Brazilian model
AR
: Argentina model
Description
Remarks
Ref. No.
When indicating parts by reference number,

please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifis par une marque
0 sont critiques pour la scurit.
Ne les remplacer que par une pice portant
le numro spcifi.
Part No.
Description
Remarks
A-7074-675-A CF-079 (SBF) BOARD, COMPLETE (TRV330)

***********************************
A-7074-677-A CF-080 (SBF) BOARD, COMPLETE (TRV530)
***********************************
A-7074-686-A CF-079 (SB) BOARD, COMPLETE (TRV230)
**********************************
(Ref.No.;1000Series)
A-7074-642-A CD-292 BOARD, COMPLETE (TRV230/TRV330)

*************************************
A-7074-670-A CD-315 BOARD, COMPLETE (TRV530)
******************************
(IC501 is not included in this COMPLETE board.)
< CAPACITOR >
< BATTERY >

C502
C507
C509
C511
1-113-985-11
1-113-682-11
1-164-360-11
1-163-021-91
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
33uF
0.1uF
0.01uF
20%
20%
10%
20V
10V
16V
50V
BT101
< CAPACITOR >
< CONNECTOR >

CN501
CN501
CN501
1-766-346-21 CONNECTOR, FFC/FPC 16P

< DIODE >
D001
D001
1-756-141-11 BATTERY, MANGANESE LITHIUM
8-719-073-01 DIODE MA111-(K8).S0

8-719-988-61 DIODE 1SS355TE-17
C101
C201
C202
C207
C208
1-162-970-11
1-135-201-11
1-107-826-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
0.1uF
0.01uF
0.01uF
10%
20%
10%
10%
10%
25V
4V
16V
25V
25V
C209
C210
C212
C213
C214
1-162-970-11
1-107-826-11
1-164-739-11
1-107-826-11
1-107-687-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.01uF
0.1uF
560PF
0.1uF
3.3uF
10%
10%
5%
10%
20%
25V
16V
50V
16V
20V
C215
C216
C217
C218
C219
1-162-964-11
1-107-826-11
1-162-928-11
1-109-982-11
1-109-982-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
120PF
1uF
1uF
10%
10%
5%
10%
10%
50V
16V
50V
10V
10V
C220
C221
1-109-982-11 CERAMIC CHIP

1uF
2.2uF
10%
10%
10V
10V
< FERRITE BEAD >

* FB5501 1-500-282-11 FERRITE
FB5502 1-414-445-11 FERRITE
0UH
0UH
< IC >
IC501
A-7031-213-A CCD BLOCK ASSY (CCD IMAGER)

< COIL >
< CONNECTOR >

L502
1-469-528-91 INDUCTOR
100uH
CN101
CN102
CN103
CN104
* CN105
< TRANSISTOR >

Q501
8-729-117-73 TRANSISTOR
2SC4178-F13F14-T1
1-794-057-21
1-785-760-11
1-794-058-21
1-779-328-21
1-695-320-21
PIN, CONNECTOR (PC BOARD) 2P

CONNECTOR, FFC/FPC (ZIF) 45P
PIN, CONNECTOR (PC BOARD) 6P
CONNECTOR, FFC/FPC 8P
PIN, CONNECTOR (1.5MM)(SMD) 2P
< RESISTOR >

R501
1-216-806-11 RES-CHIP
56
5%
1/16W
R503
1-216-864-91 SHORT
0
R504
1-216-828-11 METAL CHIP
3.9K
5%
1/16W
R505
1-216-857-11 METAL CHIP
1M
5%
1/16W
R506
1-216-845-11 METAL CHIP
100K
5%
1/16W
************************************************************
Be sure to read Precautions upon replacing CCD imager

on page 4-10 when changing the CCD imager.
6-13
CN106
CN107
CN201

CF-079
Ref. No.
CF-080
Part No.
Description
Remarks
Ref. No.
< DIODE >

D101
D102
D103
D104
D105
8-719-062-16
8-719-062-16
8-719-066-44
8-719-073-01
8-719-056-85
DIODE
DIODE
DIODE
DIODE
DIODE
01ZA8.2(TPL3)
01ZA8.2(TPL3)
CL-270HR-C-TS (TRV330/TRV530)
MA111-(K8).S0
UDZS-TE17-8.2B
D106
D107
D108
D109
D202
8-719-062-16
8-719-062-16
8-719-062-16
8-719-056-85
8-713-102-80
DIODE
DIODE
DIODE
DIODE
DIODE
01ZA8.2(TPL3)
01ZA8.2(TPL3)
01ZA8.2(TPL3)
UDZS-TE17-8.2B
1T369-01-T8A
Part No.
Description
Remarks
R123
R124
1-216-832-11 METAL CHIP

1-216-832-11 METAL CHIP
8.2K
8.2K
R125
R126
1-216-838-11 METAL CHIP

1-216-838-11 METAL CHIP
27K
27K
R127
1-216-838-11 METAL CHIP
27K
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
R128
1-216-841-11 METAL CHIP
47K
5%
R129
R130
R131
R203
1-216-822-11
1-216-821-11
1-216-803-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.2K
1K
33
470K
5%
5%
5%
5%
1/16W
(TRV230)
1/16W
1/16W
1/16W
1/16W
R205
R209
R210
R211
R212
1-218-881-11
1-216-826-11
1-216-841-11
1-216-843-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
27K
2.7K
47K
68K
22K
0.5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R213
R214
R215
R216
R217
1-216-843-11
1-216-857-11
1-216-845-11
1-216-816-11
1-216-816-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68K
1M
100K
390
390
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R218
R219
R220
R221
R222
1-216-816-11
1-216-848-11
1-216-839-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
390
180K
33K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R226
R227
R228
R229
R230
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R231
R232
1-216-864-91 SHORT
1-216-864-91 SHORT
0
0
< FERRITE BEAD >

FB201
FB201
FB201
FB202
FB202
1-414-760-21
1-414-760-21
1-500-329-21
1-414-760-21
1-414-760-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0UH
0UH
0UH
0UH
0UH
FB202
1-500-329-21 FERRITE
0UH
< IC >
IC201
IC202
8-752-100-84 IC CXA3579R-T4
8-752-405-57 IC CXD3501AR-T4
< COIL >
L201
L202
1-469-525-91 INDUCTOR
1-412-949-21 INDUCTOR
10uH
6.8uH
< TRANSISTOR >

Q101
Q102
Q103
2SC4116YG-TE85L
2SA1362-YG-EL
RN1104F(TPL3)
(TRV330/TRV530)
< RESISTOR >

< SWITCH >
R101
R102
1-216-821-11 METAL CHIP

1-216-810-11 METAL CHIP
1K
120
R103
R105
R106
1-216-813-11 METAL CHIP

1-216-845-11 METAL CHIP
1-216-807-11 METAL CHIP
220
100K
68
R108
R109
R110
1-216-815-11 METAL CHIP

1-216-822-11 METAL CHIP
1-216-822-11 METAL CHIP
330
1.2K
1.2K
R111
R112
1-216-823-11 METAL CHIP

1-216-295-11 SHORT
1.5K
0
R113
R114
R115
1-216-814-11 METAL CHIP

1-216-823-11 METAL CHIP
1-216-823-11 METAL CHIP
270
1.5K
1.5K
R116
R117
1-216-825-11 METAL CHIP

1-216-825-11 METAL CHIP
2.2K
2.2K
R118
1-216-825-11 METAL CHIP
2.2K
R119
R120
R121
1-216-828-11 METAL CHIP

1-216-828-11 METAL CHIP
1-216-828-11 METAL CHIP
3.9K
3.9K
3.9K
R122
1-216-832-11 METAL CHIP
8.2K
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
5%
1/16W
5%
1/16W
5%
1/16W
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
S101
S102
S103
S104
S105
1-771-138-82
1-771-138-82
1-771-138-82
1-771-138-82
1-771-138-82
S106
1-771-138-82 SWITCH, KEY BOARD (MS INDEX)

(TRV330/TRV530)
1-771-138-82 SWITCH, KEY BOARD (DISPLAY)
1-771-138-82 SWITCH, KEY BOARD (TITLE)
1-771-138-82 SWITCH, KEY BOARD (MS DELETE)
(TRV330/TRV530)
1-771-138-82 SWITCH, KEY BOARD (PB ZOOM)
S107
S108
S109
S110
5%
1/16W
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
S111
S112
S113
S114
S115
SWITCH, KEY BOARD (RESET)

SWITCH, KEY BOARD (MENU)
SWITCH, KEY BOARD (MS +)(TRV330/TRV530)
SWITCH, KEY BOARD (MS -)(TRV330/TRV530)
SWITCH, KEY BOARD (END SEARCH)
1-771-138-82 SWITCH, KEY BOARD (VOLUME +)

1-771-138-82 SWITCH, KEY BOARD (MS PLAY)
(TRV330/TRV530)
1-771-138-82 SWITCH, KEY BOARD (VOLUME -)
1-771-138-82 SWITCH, KEY BOARD (MEMORY MIX)
(TRV330/TRV530)
1-771-138-82 SWITCH, KEY BOARD (BACK LIGHT)
S116
1-771-138-82 SWITCH, KEY BOARD (EDIT SEARCH -)
S117
1-771-138-82 SWITCH, KEY BOARD (EDIT SEARCH +)
S118
1-771-138-82 SWITCH, KEY BOARD (FADER)
************************************************************
6-14
FP-270
Ref. No.
Part No.
FP-271
Description
Remarks
FP-272
Ref. No.

**********************
FP-273
Part No.
Description
Remarks
< CONNECTOR >
8-719-056-85 DIODE UDZS-TE17-8.2B

8-719-056-85 DIODE UDZS-TE17-8.2B
CN202
1-779-369-11 CONNECTOR, SQUARE TYPE(INDI)4P

(DV IN/OUT)
< JACK >

J101
J102
FP-275

**********************
< DIODE >

D101
D102
FP-274
< DIODE >
1-770-860-11 CONNECTOR, S TERMINAL (S VIDEO)

1-778-040-11 JACK, SMALL TYPE (AUDIO/VIDEO)
D202
8-719-064-61 DIODE 01BZA8.2(TE85L)

< JACK >
< RESISTOR >

J201
R101
R102
R104
R105
R107
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R108
R109
R110
1-216-864-91 SHORT
1-216-864-91 SHORT
0
0
0.1UF
10%
R111
0.1UF
10%
1-793-995-11 JACK, SUPER SMALL TYPE (LANC)

< RESISTOR >
R204
R205
R207
1-216-817-11 METAL CHIP

1-216-864-91 SHORT
1-216-864-91 SHORT
470
0
0
5%
1/16W
< VARISTOR >

16V
(Note)
16V
(Note)
VDR201 1-801-923-11 VARISTOR, CHIP

************************************************************
**********************
< VARISTOR >

************************************************************
< JACK >

J301
J302
1-695-514-21 JACK (SMALL TYPE) 1P (HEADPHONES)

1-691-737-11 JACK (SMALL TYPE) (MIC (PLUG IN POWER))
< PHOTO INTERRUPTER >
A-7074-649-A FP-271 BOARD, COMPLETE (TRV330/TRV530)

*************************************
< CAPACITOR >
C201
PH301 8-749-014-54 DIODE RPI-222N1

PH301 8-759-014-54 HIC CNA1312K01S0
PH302 8-749-014-54 DIODE RPI-222N1
PH302 8-759-014-54 HIC CNA1312K01S0
************************************************************
0.0022uF 10%
50V
(TRV330/TRV530)
1-680-134-11 FP-274 FLEXIBLE BOARD (TRV330/TRV530)

***********************************
< CONNECTOR >

CN201
1-794-962-11 CONNECTOR, SQUARE TYPE(USB 5P)

(DIGITAL I/O (USB))(TRV330/TRV530)
************************************************************
**********************
< DIODE >

D201
8-719-073-01 DIODE MA111-(K8).S0 (TRV330/TRV530)

< DIODE >
< LINE FILTER >
LF201
1-419-100-21 COIL, COMMON-MODE CHOKE

(TRV330/TRV530)
LF202 1-419-100-21 COIL, COMMON-MODE CHOKE
(TRV330/TRV530)
************************************************************
Note : Capacitor is mounted to the location where R110,R111 are

printed.
6-15
D401
D402
8-719-074-30 DIODE SML-310LTT86

8-719-064-61 DIODE 01BZA8.2(TE85L)
< RESISTOR >
R403
R404
R405
R406
R407
1-216-825-11
1-216-828-11
1-216-823-11
1-216-832-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
3.9K
1.5K
8.2K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
FP-275
Ref. No.
R408
R409
R410
FP-282
Part No.
FP-283
FU-150
Description
1-216-828-11 METAL CHIP

1-216-821-11 METAL CHIP
1-216-823-11 METAL CHIP
FU-154
Remarks
3.9K
1K
1.5K
5%
5%
5%
Ref. No.
1/16W
1/16W
1/16W
D407
D408
Part No.
Description
Remarks
8-719-062-16 DIODE 01ZA8.2(TPL3)

8-719-027-76 DIODE 1SS357-TPH3
< FUSE >
< SWITCH >

S401
S402
S403
S404
S405
1-771-138-82
1-771-138-82
1-771-138-82
1-771-138-82
1-771-138-82
SWITCH, KEY BOARD (STOP)

SWITCH, KEY BOARD (SUPER NIGHT SHOT)
SWITCH, KEY BOARD (FF)
SWITCH, KEY BOARD (PAUSE)
SWITCH, KEY BOARD (SUPER LASER LINK)
0 F401
0 F402
0 F403
0 F404
0 F405
1-576-406-21
1-576-406-21
1-576-406-21
1-576-406-21
1-576-406-21
0 F406
1-576-406-21 FUSE, MICRO (1608) (1.4A)
S406
1-771-138-82 SWITCH, KEY BOARD (REC)
S407
1-771-138-82 SWITCH, KEY BOARD (REW)
S408
1-771-138-82 SWITCH, KEY BOARD (REC)
S409
1-771-138-82 SWITCH, KEY BOARD (PLAY)
************************************************************
FUSE, MICRO (1608) (1.4A)

FUSE, MICRO (1608) (1.4A) (TRV330/TRV530)
< COIL >

L401
1-412-056-11 INDUCTOR
4.7uH
< TRANSISTOR >

**********************
< SWITCH >
S501
1-762-650-21 SWITCH, SLIDE (FOCUS AUTO/MANUAL)
************************************************************
**********************
Q401
Q402
Q403
Q404
Q405
8-729-047-68
8-729-051-49
8-729-804-41
8-729-042-29
8-729-042-29
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q407
Q408
Q409
Q410
Q411
Q412
< SWITCH >

S601
1-771-483-81 SWITCH, PUSH (1 KEY)(PANEL REV)
************************************************************
< CAPACITOR >

1-107-826-11
1-107-826-11
1-164-227-11
1-119-751-11
1-119-751-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
C406
C409
C410
1-119-751-11 TANTAL. CHIP

0.1uF
0.1uF
0.022uF
22uF
22uF
10%
10%
10%
20%
20%
22uF
1uF
1uF
20%
16V
10%
10V
10%
10V
(TRV330/TRV530)
16V
16V
25V
16V
16V
< CONNECTOR >

* CN401
CN402
CN403
1-580-789-21 PIN, CONNECTOR (SMD) 6P

1-691-520-11 CONNECTOR, BOARD TO BOARD 48P
< DIODE >
D401
D402
D404
D405
D406
8-719-027-76
8-719-062-16
8-719-056-85
8-719-062-16
8-719-062-16
DIODE
DIODE
DIODE
DIODE
DIODE
MGSF3455VT1 (TRV230)
HAT1054R-EL
(TRV330/TRV530)
2SJ305(TE85L)
RN2104F(TPL3)
RN2104F(TPL3)
(TRV330/TRV530)
2SJ305(TE85L)
(TRV330/TRV530)
< RESISTOR >

**********************************
**********************************
A-7074-687-A FU-150 (N) BOARD, COMPLETE (TRV230)
*********************************
C401
C402
C403
C404
C405
SSM3K03FE(TPL3)
HAT1054R-EL
2SB1122-ST-TD
RN1104F(TPL3)
RN1104F(TPL3)
R401
R402
R403
R406
R407
1-216-821-11
1-216-295-11
1-216-821-11
1-216-853-11
1-216-857-11
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
1K
0
1K
470K
1M
R408
R409
R410
R420
1-216-150-91
1-216-821-11
1-216-831-11
1-216-821-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
1K
6.8K
1K
R421
1-216-821-11 METAL CHIP
1K
R422
R423
R424
R425
1-216-857-11
1-216-809-11
1-216-841-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
100
47K
100
R426
1-216-857-11 METAL CHIP
1M
R427
1-216-841-11 METAL CHIP
47K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/8W
5%
1/16W
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
(TRV330/TRV530)
5%
1/16W
5%
1/16W
5%
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
(TRV330/TRV530)
5%
1/16W
(TRV330/TRV530)
R429
1-216-296-91 SHORT
0
R430
1-216-296-91 SHORT
0
************************************************************
1SS357-TPH3
01ZA8.2(TPL3)
UDZS-TE17-8.2B
01ZA8.2(TPL3)
01ZA8.2(TPL3)
6-16
Note :
specified.
Note :
pour la scurit.
LB-068
Ref. No.
Part No.
Description
Remarks
Ref. No.
A-7074-676-A LB-068 (SB) BOARD, COMPLETE

(TRV230/TRV330)
**************************************
A-7074-678-A LB-070 (SB) BOARD, COMPLETE (TRV530)
***********************************
< CAPACITOR >
C702
2.2uF
16V
LB-070
PC-082
Part No.
Description
C1174
C1175
C1176
C1177
C1178
1-135-201-11
1-162-913-11
1-162-913-11
1-107-826-11
1-107-826-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
8PF
8PF
0.1uF
0.1uF
20%
0.50PF
0.50PF
10%
10%
4V
50V
50V
16V
16V
Remarks
C1179
C1180
C1181
C1182
C1183
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C1185
C1189
C1190
C1191
C1192
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C1194
C1195
C1196
C1197
C1902
1-162-970-11
1-107-826-11
1-107-826-11
1-135-201-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
10uF
0.1uF
10%
10%
10%
20%
10%
25V
16V
16V
4V
16V
C1903
C1904
C1905
C1906
C1907
1-107-826-11
1-135-201-11
1-135-201-11
1-164-315-11
1-107-826-11
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
470PF
0.1uF
10%
20%
20%
2%
10%
16V
4V
4V
50V
16V
C1908
C1909
C1910
C1911
C1912
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C1914
0.1uF
10%
16V
< CONNECTOR >

CN701
CN702
CN702
CN702
1-779-334-11
1-573-356-21
1-691-354-21
1-750-340-21

CONNECTOR, FFC/EPC (ZIF) 16P
< DIODE >
D701
D702
8-719-082-33 DIODE NSCW100-T38

8-719-074-30 DIODE SML-310LTT86
< IC >
IC701
8-759-581-11 IC NJM2125F(TE2)
< TRANSISTOR >
Q701
Q702
UP04601008S0
UP04312008S0
< RESISTOR >

R701
R702
R703
R704
R705
1-218-883-11
1-218-901-11
1-216-827-11
1-211-985-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
180K
3.3K
47
1K
0.5%
0.5%
5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< CONNECTOR >
R706
1-216-839-11 METAL CHIP
33K
5%
1/16W
************************************************************
CN1152 1-779-327-11 CONNECTOR, FFC/FPC 6P

CN1901 1-774-603-21 CONNECTOR, BOARD TO BOARD 100P
A-7074-647-A PC-082 BOARD, COMPLETE (TRV330/TRV530)

*************************************
< DIODE >

D1151
D1152
< CAPACITOR >

C1151
C1154
C1156
C1158
C1160
1-107-826-11
1-107-826-11
1-107-826-11
1-164-315-11
1-164-315-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
470PF
470PF
10%
10%
10%
2%
2%
16V
16V
16V
50V
50V
C1161
C1163
C1166
C1167
C1168
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-135-201-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.1uF
0.1uF
0.1uF
0.1uF
10uF
10%
10%
10%
10%
20%
16V
16V
16V
16V
4V
C1169
C1170
C1171
C1172
C1173
1-135-201-11
1-107-826-11
1-107-826-11
1-107-826-11
1-135-201-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
10uF
0.1uF
0.1uF
0.1uF
10uF
20%
10%
10%
10%
20%
4V
16V
16V
16V
4V
8-719-073-01 DIODE MA111-(K8).S0

8-719-056-85 DIODE UDZS-TE17-8.2B
< FERRITE BEAD >
FB1151
FB1152
FB1153
FB1154
FB1155
1-414-760-21
1-414-760-21
1-414-813-11
1-414-760-21
1-500-282-11
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0UH
0UH
0UH
0UH
0UH
FB1156
FB1158
FB1902
FB1903
1-414-760-21
1-414-760-21
1-414-760-21
1-414-760-21
FERRITE
FERRITE
FERRITE
FERRITE
0UH
0UH
0UH
0UH
< IC >
IC1151
IC1152
IC1153
IC1154
IC1155
6-17
8-759-271-88
8-759-234-20
8-759-665-38
8-759-714-41
8-759-668-50
IC
IC
IC
IC
IC
TC7SHU04FU-TE85R
TC7S08F(TE85R)
MB81F161622C-80FN
MBM29LV400BC-90PFTN-S112-ER
HD6417197FL77
PC-082
Ref. No.
IC1157
IC1158
IC1159
IC1160
IC1901
PD-138
Part No.
Description
8-759-657-69
8-759-525-53
8-759-082-58
8-759-082-58
8-759-699-91
IC
IC
IC
IC
IC
Remarks
Ref. No.
PDIUSBP11APW,118
RN5RZ31BA-TL
TC7W08FU(TE12R)
TC7W08FU(TE12R)
MB87J4421PFF-G-BND
< COIL >

L1151
1-469-528-91 INDUCTOR
100uH
< TRANSISTOR >

Q1153
Q1154
Q1155
Q1156
Q1902
8-729-042-29
8-729-042-72
8-729-037-53
8-729-037-61
8-729-037-61
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q1903
RN1104F(TPL3)
RN1107F(TPL3)
2SA1832F-Y/GR(TPL3)
RN2104F(TPL3)
RN2104F(TPL3)
SHORT
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
0
1M
0
4.7K
47K
R1156
R1157
R1158
R1159
R1160
1-216-857-11
1-216-864-91
1-216-864-91
1-216-845-11
1-216-845-11
METAL CHIP
SHORT
SHORT
METAL CHIP
METAL CHIP
R1161
R1163
R1165
R1166
R1167
1-216-829-11
1-216-805-11
1-216-845-11
1-216-845-11
1-216-845-11
R1168
R1169
R1170
R1171
R1172
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
100
470K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1903
R1905
R1906
R1907
R1912
1-216-864-91
1-216-864-91
1-216-841-11
1-216-864-91
1-216-864-91
SHORT
SHORT
METAL CHIP
SHORT
SHORT
0
0
47K
0
0
5%
1/16W
R1914
1-216-864-91 SHORT
RB1151
RB1152
RB1154
RB1155
RB1156
< RESISTOR >

1-216-864-91
1-216-857-11
1-216-864-91
1-216-829-11
1-216-841-11
Description
1-216-853-11
1-216-809-11
1-216-853-11
1-216-845-11
1-216-821-11
Remarks
< COMPOSITION CIRCUIT BLOCK >
RN1104F(TPL3)
R1151
R1152
R1153
R1154
R1155
Part No.
R1203
R1205
R1207
R1208
R1211
1-234-377-21
1-234-377-21
1-234-381-21
1-234-381-21
1-234-381-21
RES, NETWORK 4.7KX4

RES, NETWORK 4.7KX4
RES, NETWORK 100KX4
RES, NETWORK 100KX4
RES, NETWORK 100KX4
(1005)
(1005)
(1005)
(1005)
(1005)
< VARISTOR >

5%
1/16W
5%
5%
1/16W
1/16W
1M
0
0
100K
100K
5%
1/16W
5%
5%
1/16W
1/16W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47
100K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1-216-845-11
1-216-845-11
1-216-827-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
3.3K
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
C5501
C5503
C5504
C5505
C5506
1-104-847-11
1-107-826-11
1-107-826-11
1-162-970-11
1-162-970-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.1uF
0.1uF
0.01uF
0.01uF
20%
10%
10%
10%
10%
4V
16V
16V
25V
25V
R1173
R1174
R1176
R1177
R1178
1-216-809-11
1-216-864-91
1-216-845-11
1-216-841-11
1-211-978-11
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
100
0
100K
47K
24
5%
1/16W
5%
5%
0.5%
1/16W
1/16W
1/16W
C5507
C5508
C5509
C5510
C5511
1-162-970-11
1-107-826-11
1-135-177-21
1-107-826-11
1-164-739-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
1uF
0.1uF
560PF
10%
10%
20%
10%
5%
25V
16V
20V
16V
50V
R1179
R1180
R1181
R1182
R1185
1-211-978-11
1-216-821-11
1-216-823-11
1-216-829-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
24
1K
1.5K
4.7K
1K
0.5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
C5512
C5513
C5514
C5515
C5516
1-107-826-11
1-107-826-11
1-135-259-11
1-164-357-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
10uF
0.001uF
100PF
10%
10%
20%
5%
5%
16V
16V
6.3V
50V
50V
R1186
R1187
R1188
R1189
R1190
1-216-829-11
1-216-864-91
1-216-864-91
1-216-845-11
1-216-845-11
METAL CHIP
SHORT
SHORT
METAL CHIP
METAL CHIP
4.7K
0
0
100K
100K
5%
1/16W
5%
5%
1/16W
1/16W
C5517
C5518
C5519
C5520
C5521
1-107-826-11
1-107-826-11
1-107-826-11
1-113-994-11
1-127-573-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
6.8uF
1uF
10%
10%
10%
20%
10%
16V
16V
16V
16V
16V
R1191
R1192
R1193
R1194
R1198
1-216-864-91
1-216-841-11
1-216-847-11
1-216-845-11
1-216-809-11
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
47K
150K
100K
100
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
C5524
C5527
C5528
C5530
C5531
1-127-573-11
1-162-970-11
1-135-177-21
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.01uF
1uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
16V
25V
20V
25V
25V

< VIBRATOR >
X1151 1-781-620-21 VIBRATOR, CERAMIC (48MHz)
X1152 1-781-762-21 VIBRATOR, CRYSTAL (25.8048MHz)
************************************************************
A-7074-646-A PD-138 (XS6) BOARD, COMPLETE
(TRV230/TRV330)
**************************************
< CAPACITOR >
6-18
PD-138
Ref. No.
Part No.
Description
C5602
C5604
C5605
C5606
0 C5607
1-115-566-11
1-164-657-11
1-107-826-11
1-107-826-11
1-131-959-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C5704
Remarks
Ref. No.
Part No.
Description
4.7uF
0.015uF
0.1uF
0.1uF
12PF
10%
10%
10%
10%
10%
10V
50V
16V
16V
3KV
R5513
R5515
R5516
R5521
R5523
1-216-857-11
1-216-864-91
1-216-833-11
1-216-864-91
1-216-809-11
METAL CHIP
SHORT
METAL CHIP
SHORT
METAL CHIP
1M
0
10K
0
100
5%
1/16W
5%
1/16W
5%
1/16W
0.1uF
10%
16V
R5524
R5525
R5551
R5553
R5557
1-216-809-11
1-216-809-11
1-216-841-11
1-216-821-11
1-216-864-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
100
100
47K
1K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R5562
R5563
R5564
R5565
R5569
1-216-833-11
1-216-841-11
1-216-857-11
1-216-857-11
1-216-848-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
47K
1M
1M
180K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5570
R5571
R5572
R5573
R5574
1-216-845-11
1-216-857-11
1-216-821-11
1-216-864-91
1-216-864-91
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
SHORT
100K
1M
1K
0
0
5%
5%
5%
1/16W
1/16W
1/16W
R5575
R5609
R5610
R5611
R5612
1-216-864-91
1-216-833-11
1-216-055-00
1-216-848-11
1-216-837-11
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
10K
1.8K
180K
22K
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
R5613
R5614
R5616
R5617
R5618
1-216-055-00
1-216-833-11
1-216-809-11
1-216-837-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.8K
10K
100
22K
470
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/16W
R5712
1-216-855-11 METAL CHIP
680K
5%
1/16W
< CONNECTOR >

CN5501
* CN5502
CN5604
CN5701
CN5703
1-691-362-11
1-573-984-11
1-764-709-11
1-794-998-21
1-766-336-21

CONNECTOR, BOARD TO BOARD 10P
CONNECTOR, FFC/FPC (LIF) 10P
PIN, CONNECTOR 20P
CN5704 1-778-508-21 PIN, CONNECTOR (PC BOARD) 6P

< DIODE >
D5502
D5503
D5601
8-713-102-80 DIODE 1T369-01-T8A

8-719-073-01 DIODE MA111-(K8).S0
8-719-073-01 DIODE MA111-(K8).S0
< FERRITE BEAD >
FB5502 1-414-760-21 FERRITE

FB5503 1-414-760-21 FERRITE
FB5504 1-414-760-21 FERRITE
0UH
0UH
0UH
< IC >
IC5501
IC5502
IC5601
IC5602
IC5701
8-759-660-92
8-759-714-77
8-759-564-49
8-759-075-70
8-759-573-02
IC
IC
IC
IC
IC
PD-139
RB5P003AM1
LZ9FF474
TC7W53FU(TE12R)
TA75S393F-TE85R
BU9735K-E2
Remarks
< TRANSFORMER >

< COIL >
L5501
L5505
L5601
1-469-525-91 INDUCTOR
1-412-956-21 INDUCTOR
1-419-387-21 INDUCTOR
0 T5601 1-435-227-11 TRANSFORMER, INVERTER

************************************************************
10uH
27uH
100uH
A-7074-674-A PD-139 (Z12) BOARD, COMPLETE (TRV530)

************************************
< TRANSISTOR >

Q5502
Q5509
Q5510
Q5511
Q5601
8-729-041-23
8-729-037-74
8-759-054-48
8-759-054-48
8-729-037-74
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q5602
Q5603
MGSF1P02LT1
UN9213J-(K8).SO
UP04601008S0
UP04601008S0
UN9213J-(K8).SO
< CAPACITOR >
FP216-TL
UP04312008S0
< RESISTOR >

R5501
R5503
R5505
R5506
R5507
1-216-853-11
1-218-895-11
1-216-835-11
1-216-826-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
100K
15K
2.7K
47K
5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5508
R5509
R5510
R5511
R5512
1-216-843-11
1-216-837-11
1-216-843-11
1-216-857-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68K
22K
68K
1M
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
6-19
C5501
C5503
C5504
C5505
C5506
1-104-847-11
1-107-826-11
1-107-826-11
1-162-970-11
1-162-970-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.1uF
0.1uF
0.01uF
0.01uF
20%
10%
10%
10%
10%
4V
16V
16V
25V
25V
C5507
C5508
C5509
C5510
C5511
1-162-970-11
1-107-826-11
1-107-687-11
1-107-826-11
1-164-739-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
3.3uF
0.1uF
560PF
10%
10%
20%
10%
5%
25V
16V
20V
16V
50V
C5512
C5515
C5516
C5517
C5518
1-107-826-11
1-164-357-11
1-162-927-11
1-109-982-11
1-109-982-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.001uF
100PF
1uF
1uF
10%
5%
5%
10%
10%
16V
50V
50V
10V
10V
Note :
specified.
Note :
pour la scurit.
PD-139
Ref. No.
SI-028
SI-029
Part No.
Description
Part No.
Description
C5519
C5532
C5533
C5534
C5536
1-109-982-11
1-109-982-11
1-115-566-11
1-109-982-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
4.7uF
1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
16V
R5509
R5510
R5511
R5512
R5523
1-216-837-11
1-216-843-11
1-216-857-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
68K
1M
100K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
C5538
C5540
C5602
C5604
C5605
1-162-970-11
1-107-826-11
1-115-566-11
1-164-657-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
4.7uF
0.015uF
0.1uF
10%
10%
10%
10%
10%
25V
16V
10V
50V
16V
R5524
R5525
R5551
R5553
R5557
1-216-809-11
1-216-809-11
1-216-841-11
1-216-841-11
1-216-864-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
100
100
47K
47K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
0.1uF
12PF
0.1uF
10%
10%
10%
16V
3KV
16V
< CONNECTOR >
R5571
R5572
R5573
R5574
R5575
1-216-809-11
1-216-833-11
1-216-833-11
1-218-917-11
1-216-843-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
100
10K
10K
820K
68K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W

CONNECTOR, BOARD TO BOARD 10P
CONNECTOR, FFC/FPC (LIF) 10P
PIN, CONNECTOR 20P
R5576
R5577
R5579
R5585
R5586
1-216-857-11
1-216-853-11
1-216-847-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
470K
150K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5587
R5588
R5590
R5591
R5592
1-216-839-11
1-216-848-11
1-216-821-11
1-216-864-91
1-216-864-91
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
SHORT
33K
180K
1K
0
0
5%
5%
5%
1/16W
1/16W
1/16W
R5609
R5610
R5611
R5612
R5613
1-216-833-11
1-216-055-00
1-216-848-11
1-216-837-11
1-216-055-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1.8K
180K
22K
1.8K
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/10W
R5614
R5616
R5617
R5618
R5712
1-216-835-11
1-216-809-11
1-216-837-11
1-216-817-11
1-216-855-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
100
22K
470
680K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
C5606
0 C5607
C5704
CN5501
* CN5502
CN5604
CN5701
CN5703

1-691-362-11
1-573-984-11
1-764-709-11
1-794-998-21
1-766-336-21
Remarks
Ref. No.
CN5704 1-778-508-21 PIN, CONNECTOR (PC BOARD) 6P

< DIODE >
D5502
D5503
D5601
8-713-102-80 DIODE 1T369-01-T8A

8-719-050-42 DIODE RD3.3UM-T1B
8-719-073-01 DIODE MA111-(K8).S0
< FERRITE BEAD >
FB5502 1-414-760-21 FERRITE

FB5504 1-414-760-21 FERRITE
0UH
0UH
< IC >
IC5501
IC5502
IC5601
IC5602
IC5701
8-752-100-84
8-752-409-15
8-759-564-49
8-759-075-70
8-759-573-02
IC
IC
IC
IC
IC
CXA3579R-T4
CXD3516R-T4
TC7W53FU(TE12R)
TA75S393F-TE85R
BU9735K-E2
Remarks
< TRANSFORMER >

0 T5601 1-435-785-21 TRANSFORMER, INVERTER
************************************************************
< COIL >

L5501
L5505
L5601
1-469-525-91 INDUCTOR
1-412-949-21 INDUCTOR
1-419-387-21 INDUCTOR
A-7074-645-A SI-028 (T) BOARD, COMPLETE

(TRV230/TRV330)
**************************************
A-7074-673-A SI-029 (T) BOARD, COMPLETE (TRV530)
*********************************
10uH
6.8uH
100uH
< TRANSISTOR >

Q5503
Q5504
Q5505
Q5506
Q5508
8-759-054-48
8-729-042-26
8-729-041-23
8-729-037-74
8-759-054-48
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q5601
Q5602
Q5603
UP04601008S0
2SB1462J-QR(K8).SO
NDS356AP
UN9213J-(K8).SO
UP04601008S0
< CAPACITOR >
UN9213J-(K8).SO
FP216-TL
UP04312008S0
< RESISTOR >

R5501
R5503
R5506
R5507
R5508
1-216-853-11
1-218-893-11
1-216-826-11
1-216-841-11
1-216-843-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
82K
2.7K
47K
68K
5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
6-20
C305
C306
C307
C308
C309
1-107-826-11
1-135-259-11
1-107-826-11
1-107-826-11
1-107-686-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.1uF
10uF
0.1uF
0.1uF
4.7uF
10%
20%
10%
10%
20%
16V
6.3V
16V
16V
16V
C310
C311
C312

0.1uF
22uF
22uF
10%
20%
20%
16V
4V
4V
Note :
specified.
Note :
pour la scurit.
SI-028
Ref. No.
Part No.
Description
Remarks
Ref. No.
< CONNECTOR >

CN301
* CN302
* CN303
CN304
1-779-331-11
1-695-320-21
1-695-320-21
1-779-337-11
< DIODE >

8-719-062-16
8-719-056-85
8-719-016-74
8-719-074-30
8-719-066-29
DIODE
DIODE
DIODE
DIODE
DIODE
D308
8-719-067-44 DIODE CL-310IRS-X-TU
Description
Remarks
01ZA8.2(TPL3)
UDZS-TE17-8.2B
1SS352-TPH3
SML-310LTT86
DCW2810
< CAPACITOR >

C1101
C1102
C1104
C1320
1-125-777-11
1-125-777-11
1-125-777-11
1-135-201-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.1uF
0.1uF
0.1uF
10uF
C1301
220PF
10%
10V
10%
10V
10%
10V
20%
4V
(TRV330/TRV530)
10%
16V
C1302
C1303
C1304
C1305
C1306
1-107-826-11
1-107-826-11
1-107-826-11
1-119-923-81
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.047uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
10V
16V
C1307
C1308
C1309
C1310
C1311
1-164-941-11
1-164-939-11
1-164-936-11
1-164-941-11
1-164-938-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.0022uF
680PF
0.0047uF
0.0015uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C1312
C1313
C1314
C1315
C1316
1-164-939-11
1-164-937-11
1-164-935-11
1-164-937-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.001uF
470PF
0.001uF
0.001uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C1317
C1318
C1319
C1321
C1322
1-164-937-11
1-164-937-11
1-164-937-11
1-115-566-11
1-135-201-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.001uF
0.001uF
0.001uF
4.7uF
10uF
10%
10%
10%
10%
20%
16V
16V
16V
10V
4V
C1323
C1326
C1327
C1328
1-115-566-11
1-115-566-11
1-115-566-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
4.7uF
4.7uF
0.01uF
10%
10%
10%
C1329
4.7uF
10V
10V
10V
50V
(TRV230/TRV330)
10%
10V
C1330
C1331
C1332
C1333
C1334
1-115-566-11
1-115-566-11
1-115-566-11
1-119-750-11
1-135-201-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
TANTALUM CHIP
4.7uF
4.7uF
4.7uF
22uF
10uF
10%
10%
10%
20%
20%
10V
10V
10V
6.3V
4V
C1335
C1336
C1337
C1338
C1339
1-135-259-11
1-119-750-11
1-164-506-11
1-164-506-11
1-135-259-11
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
10uF
22uF
4.7uF
4.7uF
10uF
20%
20%
6.3V
6.3V
16V
16V
6.3V
< FUSE >

0 F301
1-533-874-11 FUSE, MICRO (200mA)

< FERRITE BEAD >
FB001
FB002
1-414-760-21 FERRITE
1-414-760-21 FERRITE
0UH (Note)
0UH (Note)
< IC >
IC301
8-749-012-83 IC PNA4S13M02S0
< COIL >
L301
1-469-525-91 INDUCTOR
10uH
< TRANSISTOR >

Q301
2SD999-T1-CLCK
< RESISTOR >

R301
R307
R308
R309
R310
1-216-815-11
1-216-864-91
1-216-800-11
1-216-001-00
1-216-823-11
METAL CHIP
SHORT
RES-CHIP
METAL CHIP
METAL CHIP
330
0
18
10
1.5K
R311
R312
R313
R314
R315
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
5%
1/16W
5%
5%
5%
1/16W
1/10W
1/16W
< SENSOR >

SE301
SE302
VC-254
A-7096-436-A VC-254 (BNA) BOARD, COMPLETE (SERVICE)

(TRV230)
**************************************
A-7096-438-A VC-254 (BFNA) BOARD, COMPLETE (SERVICE)
(TRV330)
**************************************
A-7096-439-A VC-254 (BFNS) BOARD, COMPLETE (SERVICE)
(TRV530)
**************************************

D303
D304
D305
D306
D307
Part No.
SI-029
1-418-252-11 SENSOR, ANGULAR VELOCITY (PITCH)

1-418-252-21 SENSOR, ANGULAR VELOCITY (YAW)
< VARISTOR >

************************************************************
Note : This part is newly added to the part with suffix No. -12
only.
6-21
Note :
specified.
20%
Note :
pour la scurit.
VC-254
Ref. No.
Part No.
Description
Remarks
C1340
C1341
C1342

10uF
10uF
0.1uF
C1343
C1344

10uF
4.7uF
6.3V
6.3V
50V
(TRV230/TRV330)
20%
6.3V
10%
10V
C1345
C1347
C1348
C1350
C1352
1-135-259-11
1-104-851-11
1-135-259-11
1-104-913-11
1-125-777-11
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
10uF
10uF
10uF
10uF
0.1uF
20%
20%
20%
20%
10%
C1354
C1355

10uF
2.2uF
20%
C1356
C1357
C1359

2.2uF
10uF
4.7uF
C1360
C1362
C1363
C1501
C1502
1-125-777-11
1-164-505-11
1-164-939-11
1-164-858-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
2.2uF
0.0022uF
22PF
0.001uF
C1503
C1504
C1505
C1506
C1507
1-164-858-11
1-115-156-11
1-115-156-11
1-131-861-91
1-135-201-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
TANTALUM CHIP
22PF
1uF
1uF
4.7uF
10uF
5%
20%
20%
16V
10V
10V
20V
4V
C1508
C1509
C1511
C1512
C1513
1-125-837-91
1-164-937-11
1-115-339-11
1-164-937-11
1-117-863-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.001uF
0.1uF
0.001uF
0.47uF
10%
10%
10%
10%
10%
6.3V
16V
50V
16V
6.3V
C1514
C1515
C1516
C1517
C1518
1-162-924-11
1-115-467-11
1-107-725-11
1-162-928-11
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
56PF
0.22uF
0.1uF
120PF
1uF
5%
10%
10%
5%
10%
50V
10V
16V
50V
6.3V
C1519
C1520
C1521
C1522
C1523
1-115-467-11
1-164-937-11
1-125-837-91
1-125-837-91
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.001uF
1uF
1uF
0.1uF
10%
10%
10%
10%
10%
10V
16V
6.3V
6.3V
16V
C1524
C1525
C1552
C1554
C1556
1-104-847-11
1-125-837-91
1-164-943-11
1-164-941-11
1-135-201-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
22uF
1uF
0.01uF
0.0047uF
10uF
20%
10%
10%
10%
20%
4V
6.3V
16V
16V
4V
C1558
C1559
C1560
C1561
C1562
1-125-777-11
1-107-826-11
1-164-935-11
1-164-943-11
1-115-467-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
470PF
0.01uF
0.22uF
10%
10%
10%
10%
10%
10V
16V
16V
16V
10V
C1563
C1564
C1565
C1566
C1568
1-125-839-91
1-164-937-11
1-117-863-11
1-164-943-11
1-164-939-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.001uF
0.47uF
0.01uF
0.0022uF
20%
10%
10%
10%
10%
6.3V
16V
6.3V
16V
16V
Ref. No.
20%
20%
6.3V
10V
6.3V
16V
10V
20V
16V
(TRV230/TRV330)
16V
20%
10V
16V
10%
10%
5%
10%
10V
16V
16V
16V
16V
6-22
Part No.
Description
C1569
C1570
C1571
C1572
C2002
1-125-837-91
1-164-943-11
1-135-259-11
1-125-777-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.01uF
10uF
0.1uF
0.1uF
10%
10%
20%
10%
10%
6.3V
16V
6.3V
10V
16V
Remarks
C2003
C2005
C2006
C2007
C2008
1-107-826-11
1-164-343-11
1-164-343-11
1-164-343-11
1-110-666-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.056uF
0.056uF
0.056uF
22uF
10%
10%
10%
10%
20%
16V
25V
25V
25V
6.3V
C2009
C2010
C2012
C2014
C2015
1-164-343-11
1-110-666-11
1-110-501-11
1-135-201-11
1-164-943-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
0.056uF
22uF
0.33uF
10uF
0.01uF
10%
20%
10%
20%
10%
25V
6.3V
16V
4V
16V
C2201
C2202
C2204
C2208
C2210
1-164-943-11
1-135-259-11
1-125-777-11
1-164-392-11
1-125-837-91
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
0.1uF
390PF
1uF
10%
20%
10%
5%
10%
16V
6.3V
10V
50V
6.3V
C2211
C2212
C2213
C2214
C2215
1-135-210-11
1-125-837-91
1-164-943-11
1-107-826-11
1-125-837-91
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
1uF
0.01uF
0.1uF
1uF
20%
10%
10%
10%
10%
10V
6.3V
16V
16V
6.3V
C2222
C2223
C2224
C2226
C2227
1-107-826-11
1-107-826-11
1-107-826-11
1-164-943-11
1-117-863-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.01uF
0.47uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
6.3V
C2229
C2230
C2232
C2233
C2234
1-164-943-11
1-164-938-11
1-135-201-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.0015uF
10uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
16V
16V
4V
16V
16V
C2236
C2238
C2240
C2242
C2243
1-107-826-11
1-125-837-91
1-125-837-91
1-115-156-11
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
1uF
1uF
1uF
10%
10%
10%
10%
16V
6.3V
6.3V
10V
6.3V
C2244
C2247
C2250
C2291
C2292
1-164-943-11
1-125-837-91
1-135-201-11
1-125-837-91
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
1uF
10uF
1uF
0.01uF
10%
10%
20%
10%
10%
16V
6.3V
4V
6.3V
16V
C2293
C3102
C3104
C3105
C3107
1-119-750-11
1-164-943-11
1-164-943-11
1-164-943-11
1-164-943-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.01uF
0.01uF
0.01uF
0.01uF
20%
10%
10%
10%
10%
6.3V
16V
16V
16V
16V
C3108
C3109
C3110
C3111
C3112
1-135-201-11
1-164-943-11
1-164-943-11
1-135-259-11
1-164-935-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
10uF
0.01uF
0.01uF
10uF
470PF
20%
10%
10%
20%
10%
4V
16V
16V
6.3V
16V
C3113
C3114
C3115
C3116
C3117
1-164-943-11
1-164-866-11
1-125-777-11
1-164-677-11
1-164-935-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
47PF
0.1uF
0.033uF
470PF
10%
5%
10%
10%
10%
16V
16V
10V
16V
16V
VC-254
Ref. No.
Part No.
Description
Part No.
Description
C3119
C3120
C3121
C3122
C3123
1-164-866-11
1-164-943-11
1-164-943-11
1-135-259-11
1-164-942-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
47PF
0.01uF
0.01uF
10uF
0.0068uF
5%
10%
10%
20%
10%
16V
16V
16V
6.3V
16V
Remarks
Ref. No.
C3332
C3333
C3334
C3335
C3337
1-164-943-11
1-164-943-11
1-164-943-11
1-125-777-11
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.1uF
1uF
10%
10%
10%
10%
10%
16V
16V
16V
10V
6.3V
C3124
C3126
C3127
C3128
C3131
1-164-942-11
1-164-943-11
1-164-943-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0068uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C3338
C3341
C3342
C3343
C3345
1-164-882-11
1-125-837-91
1-125-837-91
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
1uF
1uF
0.01uF
0.01uF
5%
10%
10%
10%
10%
16V
6.3V
6.3V
16V
16V
C3133
C3134
C3135
C3136
C3137
1-125-777-11
1-125-777-11
1-164-874-11
1-164-872-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
100PF
82PF
0.01uF
10%
10%
5%
5%
10%
10V
10V
16V
16V
16V
C3346
C3348
C3601
C3603
C3604
1-164-943-11
1-164-943-11
1-135-201-11
1-164-943-11
1-135-259-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTAL. CHIP
0.01uF
0.01uF
10uF
0.01uF
10uF
10%
10%
20%
10%
20%
16V
16V
4V
16V
6.3V
C3138
C3139
C3141
C3142
C3143
1-164-874-11
1-164-878-11
1-164-882-11
1-164-882-11
1-164-882-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
150PF
220PF
220PF
220PF
5%
5%
5%
5%
5%
16V
16V
16V
16V
16V
C3608
C3610
C3611
C3612
C3614
1-125-777-11
1-135-201-11
1-162-970-11
1-125-837-91
1-162-970-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.01uF
1uF
0.01uF
10%
20%
10%
10%
10%
10V
4V
25V
6.3V
25V
C3144
C3202
C3203
C3205
C3206
1-164-882-11
1-164-943-11
1-135-259-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.01uF
10uF
0.01uF
0.01uF
5%
10%
20%
10%
10%
16V
16V
6.3V
16V
16V
C3615
C3616
C3617
C3618
C3619
1-125-777-11
1-162-970-11
1-162-970-11
1-162-970-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
10V
25V
25V
25V
16V
C3210
C3212
C3213
C3215
C3216
1-164-941-11
1-164-943-11
1-119-923-81
1-164-943-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.01uF
0.047uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
10V
16V
10V
C3620
C3622
C3626
C3629
C3631
1-164-943-11
1-162-970-11
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
25V
10V
10V
10V
C3217
C3301
C3302
C3303
C3305
1-164-943-11
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
10V
10V
10V
10V
C3633
C3634
C3636
C3701
C3702
1-135-201-11
1-125-777-11
1-164-858-11
1-164-943-11
1-164-943-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
22PF
0.01uF
0.01uF
20%
10%
5%
10%
10%
4V
10V
16V
16V
16V
C3306
C3307
C3308
C3309
C3310
1-164-943-11
1-164-850-11
1-164-850-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10PF
10PF
0.01uF
0.01uF
10%
0.50PF
0.50PF
10%
10%
16V
16V
16V
16V
16V
C3704
C3705
C3706
C3707
C3708
1-115-467-11
1-110-501-11
1-164-943-11
1-125-837-91
1-125-838-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.33uF
0.01uF
1uF
2.2uF
10%
10%
10%
10%
10%
10V
16V
16V
6.3V
6.3V
C3311
C3312
C3313
C3314
C3315
1-164-943-11
1-164-943-11
1-164-937-11
1-164-937-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C3709
C3710
C3711
C3712
C3714
1-164-677-11
1-125-838-11
1-125-838-11
1-125-838-11
1-135-259-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.033uF
2.2uF
2.2uF
2.2uF
10uF
10%
10%
10%
10%
20%
16V
6.3V
6.3V
6.3V
6.3V
C3316
C3317
C3318
C3319
C3320
1-164-937-11
1-164-943-11
1-164-943-11
1-164-937-11
1-135-201-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.001uF
0.01uF
0.01uF
0.001uF
10uF
10%
10%
10%
10%
20%
16V
16V
16V
16V
4V
C3715
C3716
C3717
C3719
C3723
1-110-501-11
1-164-943-11
1-125-837-91
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.33uF
0.01uF
1uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
6.3V
16V
16V
C3321
C3322
C3323
C3324
C3325
1-164-943-11
1-117-863-11
1-164-943-11
1-119-923-81
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.47uF
0.01uF
0.047uF
0.001uF
10%
10%
10%
10%
10%
16V
6.3V
16V
10V
16V
C3724
C3728
C3729
C3730
C3731
1-125-777-11
1-125-838-11
1-125-838-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
2.2uF
2.2uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
10V
6.3V
6.3V
16V
16V
C3326
C3327
C3328
C3329
C3331
1-125-838-11
1-104-847-11
1-164-943-11
1-164-943-11
1-135-201-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
2.2uF
22uF
0.01uF
0.01uF
10uF
10%
20%
10%
10%
20%
6.3V
4V
16V
16V
4V
C3732
C3733
C3734
C3735
C3902
1-126-246-11
1-126-246-11
1-135-259-11
1-164-943-11
1-135-201-11
ELECT CHIP
ELECT CHIP
TANTAL. CHIP
CERAMIC CHIP
TANTALUM CHIP
220uF
220uF
10uF
0.01uF
10uF
20%
20%
20%
10%
20%
4V
4V
6.3V
16V
4V
6-23
Remarks
VC-254
Ref. No.
Part No.
Description
Part No.
Description
C3903
C3904
C3905
C3906
C3908
1-135-259-11
1-164-943-11
1-117-863-11
1-117-863-11
1-125-837-91
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.01uF
0.47uF
0.47uF
1uF
20%
10%
10%
10%
10%
6.3V
16V
6.3V
6.3V
6.3V
Remarks
Ref. No.
C4435
C4436
C4437
C4438
C4439
1-164-935-11
1-164-935-11
1-125-777-11
1-125-777-11
1-113-619-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
0.1uF
0.1uF
0.47uF
10%
10%
10%
10%
16V
16V
10V
10V
10V
C3909
C3910
C3911
C3912
C3913
1-164-943-11
1-135-210-11
1-164-943-11
1-164-943-11
1-164-668-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
4.7uF
0.01uF
0.01uF
510PF
10%
20%
10%
10%
5%
16V
10V
16V
16V
50V
C4440
C4441
C4442
C4501
C4504
1-107-826-11
1-107-826-11
1-107-826-11
1-164-937-11
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.001uF
1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
6.3V
C3914
C3915
C3916
C3917
C3918
1-135-259-11
1-164-943-11
1-125-837-91
1-107-826-11
1-164-844-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.01uF
1uF
0.1uF
4PF
20%
10%
10%
10%
0.25PF
6.3V
16V
6.3V
16V
16V
C4505
C4506
C4507
C4508
C4509
1-164-943-11
1-164-943-11
1-164-943-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C3919
C3920
C3921
C3922
C3923
1-117-863-11
1-117-863-11
1-164-862-11
1-125-837-91
1-164-864-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.47uF
33PF
1uF
39PF
10%
10%
5%
10%
5%
6.3V
6.3V
16V
6.3V
16V
C4510
C4801
C4802
C4803
C4804
1-164-943-11
1-115-156-11
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
16V
10V
10V
10V
10V
C3924
C3925
C3926
C3927
C3928
1-125-837-91
1-107-826-11
1-164-943-11
1-164-943-11
1-104-847-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
1uF
0.1uF
0.01uF
0.01uF
22uF
10%
10%
10%
10%
20%
6.3V
16V
16V
16V
4V
C4805
C4806
C4807
C4808
C4810
1-104-851-11
1-119-749-11
1-125-777-11
1-164-943-11
1-164-943-11
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
33uF
0.1uF
0.01uF
0.01uF
20%
20%
10%
10%
10%
10V
4V
10V
16V
16V
C3934
C3935
C3936
C4401
C4402
1-125-837-91
1-164-943-11
1-164-943-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.01uF
0.01uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
6.3V
16V
16V
10V
10V
C4811
C4812
C4813
C4814
C4815
1-164-943-11
1-164-943-11
1-164-943-11
1-164-943-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
10V
C4403
C4404
C4405
C4406
C4407
1-125-777-11
1-125-777-11
1-107-819-11
1-107-819-11
1-119-923-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.022uF
0.022uF
0.047uF
10%
10%
10%
10%
10%
10V
10V
16V
16V
10V
C4816
C4817
C4819
C4820
C4821
1-125-777-11
1-125-777-11
1-107-819-11
1-164-942-11
1-164-858-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.022uF
0.0068uF
22PF
10%
10%
10%
10%
5%
10V
10V
16V
16V
16V
C4408
C4409
C4410
C4411
C4412
1-104-912-11
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
3.3uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
6.3V
10V
10V
10V
10V
C4822
C4823
C4824
C4825
C4827
1-164-854-11
1-125-777-11
1-125-777-11
1-125-777-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
15PF
0.1uF
0.1uF
0.1uF
0.01uF
5%
10%
10%
10%
10%
16V
10V
10V
10V
16V
C4413
C4414
C4415
C4416
C4417
1-125-777-11
1-164-933-11
1-164-935-11
1-125-777-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
220PF
470PF
0.1uF
0.001uF
10%
10%
10%
10%
10%
10V
16V
16V
10V
16V
C4902
C4903
C4904
C4905
C4906
1-125-837-91
1-164-850-11
1-164-850-11
1-164-943-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
10PF
10PF
0.01uF
0.1uF
10%
0.50PF
0.50PF
10%
10%
6.3V
16V
16V
16V
10V
C4418
C4419
C4420
C4421
C4424
1-164-935-11
1-164-937-11
1-125-837-91
1-164-937-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
0.001uF
1uF
0.001uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
6.3V
16V
10V
C4907
C4908
C4909
C4910
C4911
1-125-777-11
1-164-943-11
1-164-943-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.01uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
16V
16V
10V
10V
C4425
C4426
C4427
C4428
C4429
1-107-819-11
1-164-943-11
1-164-943-11
1-119-923-81
1-119-923-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.01uF
0.01uF
0.047uF
0.047uF
10%
10%
10%
10%
10%
16V
16V
16V
10V
10V
C4912
C5701
C5702
C5703
C5704
1-164-943-11
1-135-201-11
1-135-201-11
1-115-467-11
1-135-259-11
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTAL. CHIP
0.01uF
10uF
10uF
0.22uF
10uF
10%
20%
20%
10%
20%
16V
4V
4V
10V
6.3V
C4430
C4431
C4432
C4433
C4434
1-164-505-11
1-125-777-11
1-164-943-11
1-164-937-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
0.1uF
0.01uF
0.001uF
0.001uF
10%
10%
10%
10%
16V
10V
16V
16V
16V
C5705
C5706
C5709
C5710
C5711
1-104-847-11
1-135-201-11
1-115-467-11
1-164-943-11
1-110-569-11
TANTAL. CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
22uF
10uF
0.22uF
0.01uF
47uF
20%
20%
10%
10%
20%
4V
4V
10V
16V
4V
6-24
Remarks
VC-254
Ref. No.
Part No.
Description
Part No.
Description
C5712
C5713
C5714
C5715
C5716
1-110-569-11
1-117-863-11
1-135-259-11
1-104-912-11
1-135-259-11
TANTAL. CHIP
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
47uF
0.47uF
10uF
3.3uF
10uF
20%
10%
20%
20%
20%
4V
6.3V
6.3V
4V
6.3V
Remarks
Ref. No.
C5824
C5825
C5826
C5827
C5829
1-125-777-11
1-125-777-11
1-165-176-11
1-165-176-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.047uF
0.047uF
0.047uF
10%
10%
10%
10%
10%
10V
10V
16V
16V
16V
Remarks
C5717
C5718
C5719
C5720
C5721
1-115-467-11
1-115-467-11
1-115-467-11
1-115-467-11
1-164-939-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.22uF
0.22uF
0.22uF
0.0022uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
16V
C5830
C5832
C5833
C5835
C5836
1-165-176-11
1-164-227-11
1-164-938-11
1-164-938-11
1-164-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.022uF
0.0015uF
0.0015uF
0.022uF
10%
10%
10%
10%
10%
16V
25V
16V
16V
25V
C5722
C5723
C5724
C5725
C5728
1-115-467-11
1-104-847-11
1-115-467-11
1-125-837-91
1-125-777-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
22uF
0.22uF
1uF
0.1uF
10%
20%
10%
10%
10%
10V
4V
10V
6.3V
10V
C5838
C5839
C5840
C5841
1-125-777-11
1-104-847-11
1-115-467-11
1-125-837-91
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22uF
0.22uF
1uF
10%
20%
10%
10%
10V
4V
10V
6.3V
C5730
C5731
C5732
C5733
C5734
1-115-467-11
1-125-837-91
1-125-837-91
1-125-837-91
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
1uF
1uF
1uF
1uF
10%
10%
10%
10%
10%
10V
6.3V
6.3V
6.3V
6.3V
C5735
C5736
C5737
C5738
C5739
1-125-777-11
1-115-467-11
1-125-837-91
1-125-837-91
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.22uF
1uF
1uF
1uF
10%
10%
10%
10%
10%
10V
10V
6.3V
6.3V
6.3V
C5740
C5741
C5742
C5743
C5744
1-115-467-11
1-115-467-11
1-164-937-11
1-164-937-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.22uF
0.001uF
0.001uF
0.01uF
10%
10%
10%
10%
10%
10V
10V
16V
16V
16V
C5745
C5746
C5747
C5748
C5749
1-164-943-11
1-117-863-11
1-117-863-11
1-164-943-11
1-164-870-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.47uF
0.47uF
0.01uF
68PF
10%
10%
10%
10%
5%
16V
6.3V
6.3V
16V
16V
C5750
C5751
C5752
C5753
C5754
1-135-201-11
1-135-201-11
1-164-943-11
1-164-943-11
1-115-467-11
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.01uF
0.01uF
0.22uF
20%
20%
10%
10%
10%
4V
4V
16V
16V
10V
D1101
D1102
D1103
D1105
D1106
8-719-062-16
8-719-062-16
8-719-062-16
8-719-062-16
8-719-056-85
DIODE
DIODE
DIODE
DIODE
DIODE
01ZA8.2(TPL3)
01ZA8.2(TPL3) (TRV330/TRV530)
01ZA8.2(TPL3)
01ZA8.2(TPL3) (TRV330/TRV530)
UDZS-TE17-8.2B (TRV330/TRV530)
C5755
C5756
C5757
C5758
C5759
1-164-942-11
1-115-467-11
1-164-942-11
1-115-467-11
1-115-467-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0068uF
0.22uF
0.0068uF
0.22uF
0.22uF
10%
10%
10%
10%
10%
16V
10V
16V
10V
10V
D1301
D1302
D1305
D1306
D1501
8-719-078-02
8-719-081-19
8-719-078-02
8-719-081-19
8-713-103-84
DIODE
DIODE
DIODE
DIODE
DIODE
1SS357(T3SONY1) (TRV230/TRV330)
1SS383(T5RSONY1)
1SS357(T3SONY1) (TRV230/TRV330)
1SS383(T5RSONY1)
1T379-01-T8A
C5806
C5807
C5808
C5809
C5810
1-164-943-11
1-107-819-11
1-107-819-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.022uF
0.022uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
D1551
D2201
D2202
D3301
D3302
8-719-073-01
8-719-081-96
8-719-081-96
8-719-992-02
8-719-081-96
DIODE
DIODE
DIODE
DIODE
DIODE
MA111-(K8).S0
KV1870STL
KV1870STL
RB705D-T146
KV1870STL
C5812
C5813
C5814
C5815
C5816
1-135-201-11
1-164-874-11
1-164-937-11
1-135-201-11
1-164-874-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
10uF
100PF
0.001uF
10uF
100PF
20%
5%
10%
20%
5%
4V
16V
16V
4V
16V
D3303
D3304
D4401
D4802
D4803
8-719-992-02
8-719-081-96
8-719-075-12
8-719-421-27
8-719-073-01
DIODE
DIODE
DIODE
DIODE
DIODE
RB705D-T146
KV1870STL
MA3XD21001S0
MA728-(K8).S0
MA111-(K8).S0
C5817
C5819
C5820
C5822
C5823
1-164-937-11
1-164-874-11
1-164-874-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
100PF
100PF
0.1uF
0.1uF
10%
5%
5%
10%
10%
16V
16V
16V
10V
10V
D4804
D4806
8-719-073-01 DIODE MA111-(K8).S0

8-719-421-67 DIODE MA132WK-(K8).SO
< CONNECTOR >

(TRV330/TRV530)
CN1115
CN1116
CN1117
CN1120
CN1501
1-766-340-21
1-779-337-11
1-785-760-21
1-794-998-21
1-779-332-11

PIN, CONNECTOR 20P
CN1551
CN3101
* CN4401
CN4402
CN4403
1-750-360-21
1-774-636-21
1-580-055-21
1-766-340-21
1-766-352-21

PIN, CONNECTOR (SMD) 2P

< DIODE >
6-25
VC-254
Ref. No.
Part No.
Description
Remarks
Ref. No.
< PIN CONNECTOR >

ET131
ET132
ET133
IC4902
IC5701
IC5702
IC5801
1-815-032-21 PIN, CONNECTOR (CASE, SHIELD)

Part No.
Description
8-759-836-62
8-752-093-72
8-759-647-71
8-759-638-50
IC
IC
IC
IC
Remarks
CXA3284R-T6
AK4550VT-E2
AN2901FHQ-EB
< COIL >

< FERRITE BEAD >
FB1501
FB1502
FB1503
FB1504
FB1505
1-414-760-21
1-500-284-21
1-500-284-21
1-414-760-21
1-500-284-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0UH
0UH
0UH
0UH
0UH
FB1506
FB2202
FB2204
FB2205
FB2291
1-500-283-11
1-414-760-21
1-414-760-21
1-414-760-21
1-414-760-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0UH
0UH
0UH
0UH
0UH
FB3303
FB3304
FB3307
FB3601
FB3701
1-414-760-21
1-414-760-21
1-414-760-21
1-414-760-21
1-414-760-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0UH
0UH
0UH
0UH
0UH
FB4501 1-414-760-21 FERRITE

FB4801 1-414-760-21 FERRITE
FB4901 1-414-760-21 FERRITE
0UH
0UH
0UH
L1301
L1302
L1303
L1304
L1305
1-416-670-11
1-416-669-11
1-416-669-11
1-416-669-11
1-416-669-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
33uH
22uH
22uH
22uH
22uH
L1306
L1307
L1308
L1309
L1310
1-412-056-11
1-412-056-11
1-469-557-21
1-469-557-21
1-412-056-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
4.7uH
4.7uH
22uH
22uH
4.7uH
L1313
L1314
L1315
L1316
L1317
1-469-553-21
1-469-553-21
1-469-553-21
1-414-400-41
1-416-669-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
4.7uH
4.7uH
4.7uH
22uH
22uH
L1318
L1319
L1320
L1501
L1551
1-412-056-11
1-412-056-11
1-469-524-91
1-469-555-21
1-469-525-91
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
4.7uH
4.7uH (TRV330/TRV530)
4.7uH
10uH
10uH
L1552
L1553
L2001
L2202
L2204
1-469-555-21
1-469-525-91
1-469-555-21
1-469-555-21
1-469-525-91
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
L2207
L2208
L2209
L2291
L3102
1-412-945-11
1-469-555-21
1-469-525-91
1-469-555-21
1-469-525-91
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
3.3uH
10uH
10uH
10uH
10uH
L3103
L3104
L3105
L3106
L3201
1-469-525-91
1-469-555-21
1-414-406-41
1-412-952-11
1-469-526-91
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
220uH
12uH
22uH
L3303
L3304
L3305
L3306
L3307
1-412-936-11
1-414-246-11
1-469-525-91
1-469-525-91
1-469-525-91
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
0.56uH
1.8uH
10uH
10uH
10uH
L3601
L3602
L3701
L3705
L3901
1-469-525-91
1-469-525-91
1-469-525-91
1-469-525-91
1-469-555-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
L3902
L3903
L3904
L5701
L5803
1-412-948-11
1-412-957-11
1-412-957-11
1-469-525-91
1-469-560-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
5.6uH
33uH
33uH
10uH
68uH
< IC >
IC1301
IC1303
IC1304
IC1501
IC1502
8-752-090-20
8-759-650-28
8-759-075-66
8-752-386-72
8-759-684-90
IC
IC
IC
IC
IC
CXA3057R-T6
RN5RZ59BA-TL
TA75S01F(TE85R)
CXD2444R-T4
VSP2200Y-1/2K
IC1552
IC1553
IC2001
IC2201
IC2291
8-759-681-42
8-759-637-96
8-759-489-19
8-759-670-78
8-759-713-19
IC
IC
IC
IC
IC
NJM12902V(TE2)
MPC17A135DTAEL
uPC6756GR-8JG-E2
HG75C012SFL
BH2222FV-E2
IC3101
IC3102
IC3103
IC3201
IC3202
8-752-086-52
8-759-195-81
8-752-086-53
8-752-093-69
8-759-075-70
IC
IC
IC
IC
IC
CXA2071R-T4
TC7S86FU(TE85R)
CXA2072R-T4
CXA3265R-T4
TA75S393F-TE85R
IC3301
IC3302
IC3303
IC3603
IC3701
8-759-650-74
8-759-714-10
8-759-566-52
8-759-653-60
8-759-599-37
IC
IC
IC
IC
IC
CAIN
MB90099PFV-G-108-BND-ER
SN104266PN-TEB
MB87L1241PFV-G-BND-ER
AN2225FHQ-EB
IC3901
IC4401
IC4402
IC4501
IC4502
8-759-498-52
8-759-640-85
8-759-431-41
8-759-835-68
8-759-593-47
IC
IC
IC
IC
IC
LA9511WL-TBM
CXA8096R-TBM
LB1991V-TLM
AK6417AM-E2
IC4801
IC4802
IC4803
IC4804
IC4901
8-759-680-14
8-759-642-45
8-752-921-67
8-759-679-91
8-759-445-94
IC
IC
IC
IC
IC
S-84239FS-T2
TL1596CPWR
CXP921064A-032R-T6
S-817A33ANB-CUW-T2
AK6480AM-E2
6-26
VC-254
Ref. No.
Part No.
Description
Remarks
Ref. No.
< TRANSISTOR >

Q1104
Q1301
Q1302
Q1303
Q1304
8-729-052-64
8-729-043-60
8-729-046-98
8-729-046-98
8-729-046-98
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC144EHT2L
CPH6102-TL
CPH6702-TL
CPH6702-TL
CPH6702-TL
Q1305
Q1306
Q1307
Q1308
Q1309
8-729-046-98
8-729-046-98
8-729-044-58
8-729-044-58
8-729-046-98
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
CPH6702-TL
CPH6702-TL
SI2304DS-T1
SI2304DS-T1
CPH6702-TL
Q1311
Q1312
Q1314
Q1316
Q1321
8-729-101-07
8-729-052-65
8-729-052-64
8-729-037-52
8-729-037-52
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB798-T1-DLDK
2SA1774HT2L
DTC144EHT2L
2SC4738F-Y/GR(TPL3)
2SC4738F-Y/GR(TPL3)
Q1323
Q1324
Q1327
Q1328
Q1329
Q1330
Q1331
Q1332
Q1333
Q1551
8-729-039-86
8-729-037-52
8-729-037-52
8-729-037-52
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UP04401008S0
(TRV230/TRV330)
FMMT717TA
2SC4738F-Y/GR(TPL3)
2SC4738F-Y/GR(TPL3)
2SC4738F-Y/GR(TPL3)
Q1554
Q1555
Q2207
Q3102
Q3103
8-729-037-52
8-729-054-51
8-759-054-48
8-729-052-65
8-729-052-64
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC4738F-Y/GR(TPL3)
UP04116008S0
UP04601008S0
2SA1774HT2L
DTC144EHT2L
Q3104
Q3107
Q3109
Q3111
Q3116
8-729-052-64
8-729-037-52
8-729-054-44
8-729-052-65
8-729-047-19
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC144EHT2L
2SC4738F-Y/GR(TPL3)
UP04111008S0
2SA1774HT2L
2SA1965-S-TL
Q3117
Q3118
Q3119
Q3120
Q3201
8-759-054-48
8-729-054-47
8-759-054-50
8-759-054-50
8-729-052-64
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UP04601008S0
UP04213008S0
UP04501008S0
UP04501008S0
DTC144EHT2L
Q3306
Q3309
Q3310
Q3601
Q3602
8-729-052-65
8-729-054-49
8-729-054-49
8-729-052-65
8-759-054-48
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1774HT2L
UP04401008S0
UP04401008S0
2SA1774HT2L
UP04601008S0
Q3701
Q3702
Q3703
Q3705
Q3902
8-729-037-52
8-729-037-61
8-729-037-52
8-729-037-52
8-729-122-63
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC4738F-Y/GR(TPL3)
RN2104F(TPL3)
2SC4738F-Y/GR(TPL3)
2SC4738F-Y/GR(TPL3)
2SA1226-T1E4
Q3903
Q4401
Q4402
Q4801
Q4802
8-729-052-65
8-729-037-52
8-729-052-64
8-729-037-52
8-729-037-52
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1774HT2L
2SC4738F-Y/GR(TPL3)
DTC144EHT2L
2SC4738F-Y/GR(TPL3)
2SC4738F-Y/GR(TPL3)
Part No.
Description
Q4804
Q4806
Q4813
Q4901
Q5708
8-729-041-43
8-729-042-58
8-729-054-47
8-729-045-71
8-729-037-63
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q5716
Q5717
Q5718
Remarks
HN1L02FU(TE85R)
RN2102F(TPL3)
UP04213008S0
RN1102F(TPL3)
RN2111F(TPL3)
UP04501008S0
UP04216008S0
UP04216008S0
< RESISTOR >
2SA1774HT2L
2SC4738F-Y/GR(TPL3)
(TRV230/TRV330)
UP04501008S0
UP04501008S0
UP04401008S0
6-27
R1105
R1106
R1107
R1108
R1109
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT
SHORT
SHORT
SHORT
SHORT
O (TRV230)
O (TRV230)
O (TRV230)
O (TRV230)
O (TRV230)
R1110
R1111
R1112
R1113
R1114
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT
SHORT
SHORT
SHORT
SHORT
O (TRV230)
O (TRV230)
O (TRV230)
O (TRV230)
O (TRV230)
R1115
R1116
R1117
R1118
R1119
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT
SHORT
SHORT
SHORT
SHORT
O (TRV230)
O (TRV230)
O (TRV230)
O (TRV230)
O (TRV230)
R1120
R1121
R1122
R1123
R1124
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-953-11
SHORT
SHORT
SHORT
SHORT
RES-CHIP
O (TRV230)
O (TRV230)
O (TRV230)
O (TRV230)
1K
5%
R1127
1-218-974-11 RES-CHIP
56K
R1127
1-218-975-11 RES-CHIP
68K
R1128
1-218-974-11 RES-CHIP
56K
R1128
1-218-975-11 RES-CHIP
68K
R1131
1-218-973-11 RES-CHIP
47K
R1131
1-218-975-11 RES-CHIP
68K
R1132
1-218-974-11 RES-CHIP
R1132
1-218-977-11 RES-CHIP
R1134
R1144
1-218-990-11 SHORT
1-218-961-11 RES-CHIP
5%
1/16W
(TRV330/TRV530)
56K
5%
1/16W
(TRV330/TRV530)
100K
5%
1/16W
(TRV230)
O (TRV230)
4.7K
5%
1/16W
R1145
R1146
R1147
R1148
R1151
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-941-11
SHORT
SHORT
SHORT
SHORT
RES-CHIP
O (TRV230)
O (TRV230)
0
0
100
5%
1/16W
R1152
R1153
R1154
R1155
R1301
1-218-941-11
1-218-941-11
1-218-941-11
1-218-941-11
1-218-969-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
100
100
22K
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
5%
1/16W
(TRV230/TRV330)
5%
1/16W
(TRV530)
5%
1/16W
(TRV530)
5%
1/16W
(TRV230/TRV330)
5%
1/16W
(TRV230)
5%
5%
5%
5%
5%
VC-254
Ref. No.
Part No.
Description
R1302
R1303
R1304
R1305
R1306
1-218-971-11
1-218-974-11
1-218-971-11
1-218-990-11
1-218-967-11
RES-CHIP
METAL CHIP
RES-CHIP
SHORT
RES-CHIP
33K
56K
33K
0
15K
5%
0.5%
5%
Remarks
1/16W
1/16W
1/16W
5%
1/16W
R1307
R1309
R1310
R1311
R1312
1-218-963-11
1-218-965-11
1-218-970-11
1-218-969-11
1-218-961-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
6.8K
10K
27K
22K
4.7K
5%
5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1313
R1314
R1316
R1317
R1318
1-218-964-11
1-218-969-11
1-216-864-91
1-218-973-11
1-218-961-11
RES-CHIP
RES-CHIP
SHORT
RES-CHIP
RES-CHIP
8.2K
22K
0
47K
4.7K
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/16W
R1319
R1320
R1321
R1322
R1323
1-218-973-11
1-218-969-11
1-208-715-11
1-208-707-11
1-218-977-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
47K
22K
22K
10K
100K
5%
5%
0.5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1326
R1327
R1330
R1331
R1332
1-218-965-11
1-218-969-11
1-208-935-11
1-218-965-11
1-208-943-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
10K
22K
100K
10K
220K
5%
5%
0.5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1333
R1334
R1335
1-218-973-11 RES-CHIP
1-218-977-11 RES-CHIP
1-218-977-11 RES-CHIP
47K
100K
100K
R1336
R1337
1-218-969-11 RES-CHIP
1-218-977-11 RES-CHIP
22K
100K
5%
1/16W
5%
1/16W
5%
1/16W
(TRV230/TRV330)
5%
1/16W
5%
1/16W
(TRV230/TRV330)
R1338
R1339
R1340
R1341
1-208-935-11
1-208-721-11
1-208-908-81
1-218-961-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
100K
39K
7.5K
4.7K
R1342
1-208-943-11 METAL CHIP
220K
R1343
1-208-931-11 METAL CHIP
68K
R1345
R1347
R1348
R1349
1-218-990-11
1-208-715-11
1-208-707-11
1-218-990-11
SHORT
METAL CHIP
METAL CHIP
SHORT
0
22K
10K
0
R1350
R1355
R1356
R1357
R1358
1-216-864-91
1-218-973-11
1-218-937-11
1-218-990-11
1-218-990-11
SHORT
RES-CHIP
RES-CHIP
SHORT
SHORT
0
47K
47
0
0
R1359
R1360
R1361
R1362
R1363
1-218-990-11
1-218-990-11
1-218-990-11
1-208-935-11
1-208-697-11
SHORT
SHORT
SHORT
METAL CHIP
METAL CHIP
0
0
0
100K
3.9K
R1364
R1365
R1366
R1369
R1370
1-218-969-11
1-218-953-11
1-218-943-11
1-208-935-11
1-208-709-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
22K
1K
150
100K
12K
Ref. No.
0.5% 1/16W
0.5% 1/16W
0.5% 1/16W
5%
1/16W
(TRV230/TRV330)
0.5% 1/16W
(TRV230/TRV330)
0.5% 1/16W
(TRV230/TRV330)
0.5%
0.5%
1/16W
1/16W
5%
5%
1/16W
1/16W
0.5%
0.5%
1/16W
1/16W
5%
1/16W
5%
1/16W
5%
1/16W
0.5% 1/16W
0.5% 1/16W
(TRV230/TRV330)
6-28
Part No.
Description
Remarks
R1370
1-208-909-11 METAL CHIP
8.2K
0.5%
1/16W
(TRV530)
R1501
R1502
R1503
R1504
1-216-864-91
1-216-864-91
1-218-977-11
1-218-941-11
SHORT
SHORT
RES-CHIP
RES-CHIP
0
0
100K
100
5%
5%
1/16W
1/16W
R1505
R1506
R1512
R1519
R1521
1-218-941-11
1-218-941-11
1-218-985-11
1-218-990-11
1-216-864-91
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
SHORT
100
100
470K
0
0
5%
5%
5%
1/16W
1/16W
1/16W
R1523
R1551
R1552
R1555
R1556
1-218-945-11
1-218-973-11
1-218-953-11
1-218-975-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
220
47K
1K
68K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1557
R1560
R1561
R1562
R1563
1-218-975-11
1-218-929-11
1-218-989-11
1-218-957-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
68K
10
1M
2.2K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1564
R1565
R1566
R1567
R1568
1-218-981-11
1-218-985-11
1-218-985-11
1-218-957-11
1-218-967-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
220K
470K
470K
2.2K
15K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1569
R1570
R1571
R1572
R1573
1-218-969-11
1-218-985-11
1-218-953-11
1-218-953-11
1-218-947-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
22K
470K
1K
1K
330
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1574
R1575
R1576
R1577
R2001
1-218-969-11
1-218-953-11
1-218-965-11
1-218-973-11
1-218-969-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
22K
1K
10K
47K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R2002
R2003
R2004
R2005
R2006
1-218-969-11
1-218-969-11
1-218-969-11
1-218-989-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
22K
22K
22K
1M
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R2007
R2008
R2010
R2205
R2206
1-218-965-11
1-218-989-11
1-218-967-11
1-218-965-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
1M
15K
10K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R2209
R2210
R2213
R2215
R2216
1-218-965-11
1-218-954-11
1-218-962-11
1-218-953-11
1-218-963-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
1.2K
5.6K
1K
6.8K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R2218
R2219
R2220
R2221
R2222
1-218-949-11
1-218-941-11
1-218-972-11
1-218-952-11
1-218-959-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470
100
39K
820
3.3K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R2223
R2224
R2225
R2226
R2227
1-218-964-11
1-218-966-11
1-218-949-11
1-218-990-11
1-218-990-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
SHORT
8.2K
12K
470
0
0
5%
5%
5%
1/16W
1/16W
1/16W
VC-254
Ref. No.
Part No.
Description
R2228
R2229
R2231
R2240
R2242
1-218-990-11
1-218-990-11
1-218-990-11
1-218-989-11
1-218-967-11
SHORT
SHORT
SHORT
RES-CHIP
RES-CHIP
0
0
0
1M
15K
Remarks
5%
5%
R2243
R2244
R2245
R2247
R2248
1-218-967-11
1-218-966-11
1-218-949-11
1-218-953-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
15K
12K
470
1K
10K
5%
5%
5%
5%
5%
R2255
R2256
R3103
R3104
R3107
1-218-990-11
1-218-990-11
1-218-965-11
1-218-963-11
1-218-979-11
SHORT
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
0
0
10K
6.8K
150K
R3108
R3109
R3110
R3111
R3113
1-218-989-11
1-218-966-11
1-218-965-11
1-218-949-11
1-218-966-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
R3114
R3115
R3117
R3118
R3119
1-218-961-11
1-218-965-11
1-218-969-11
1-220-196-11
1-218-970-11
R3120
R3121
R3122
R3123
R3124
Ref. No.
Part No.
Description
1/16W
1/16W
R3315
R3316
R3317
R3318
R3319
1-218-959-11
1-218-959-11
1-218-961-11
1-218-965-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
3.3K
3.3K
4.7K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
R3320
R3321
R3322
R3323
R3324
1-218-957-11
1-218-959-11
1-218-941-11
1-218-947-11
1-218-961-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
3.3K
100
330
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
RES-CHIP
SHORT
METAL CHIP
RES-CHIP
SHORT
47
0
1.2K
4.7K
0
1/16W
1/16W
1/16W
1/16W
1-218-937-11
1-218-990-11
1-218-849-11
1-218-961-11
1-218-990-11
5%
5%
5%
5%
R3325
R3326
R3328
R3331
R3333
0.5%
5%
1/16W
1/16W
1M
12K
10K
470
12K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3334
R3336
R3337
R3338
R3340
1-218-849-11
1-218-961-11
1-218-990-11
1-208-683-11
1-218-849-11
METAL CHIP
RES-CHIP
SHORT
METAL CHIP
METAL CHIP
1.2K
4.7K
0
1K
1.2K
0.5%
5%
1/16W
1/16W
0.5%
0.5%
1/16W
1/16W
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
4.7K
10K
22K
13K
27K
5%
5%
5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3343
R3346
R3349
R3350
R3351
1-218-961-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-946-11
RES-CHIP
SHORT
SHORT
SHORT
RES-CHIP
4.7K
0
0
0
270
5%
1/16W
5%
1/16W
1-208-715-11
1-208-709-11
1-208-931-11
1-218-969-11
1-218-969-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
22K
12K
68K
22K
22K
0.5%
0.5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3352
R3356
R3358
R3360
R3361
1-218-990-11
1-218-957-11
1-218-945-11
1-218-957-11
1-208-709-11
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
0
2.2K
220
2.2K
12K
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
R3125
R3126
R3127
R3128
R3129
1-218-945-11
1-218-969-11
1-218-971-11
1-218-965-11
1-218-945-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
220
22K
33K
10K
220
0.5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3362
R3364
R3365
R3367
R3368
1-218-990-11
1-208-709-11
1-218-990-11
1-218-938-11
1-218-938-11
SHORT
METAL CHIP
SHORT
RES-CHIP
RES-CHIP
0
12K
0
56
56
0.5%
1/16W
5%
5%
1/16W
1/16W
R3130
R3131
R3132
R3133
R3136
1-218-945-11
1-218-945-11
1-218-946-11
1-218-945-11
1-218-957-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
220
220
270
220
2.2K
0.5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3369
R3370
R3372
R3375
R3376
1-218-864-11
1-218-938-11
1-218-938-11
1-218-965-11
1-218-953-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
5.1K
56
56
10K
1K
0.5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3137
R3138
R3139
R3140
R3141
1-218-961-11
1-218-941-11
1-218-960-11
1-218-960-11
1-218-960-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
100
3.9K
3.9K
3.9K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3385
R3386
R3394
R3395
R3396
1-216-864-91
1-216-864-91
1-218-990-11
1-218-990-11
1-218-990-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R3142
R3143
R3144
R3205
R3206
1-218-960-11
1-218-938-11
1-218-950-11
1-218-985-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
3.9K
56
560
470K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3397
R3398
R3607
R3611
R3617
1-218-990-11
1-218-990-11
1-218-965-11
1-218-965-11
1-218-951-11
SHORT
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
0
0
10K
10K
680
5%
5%
5%
1/16W
1/16W
1/16W
R3210
R3212
R3213
R3214
R3215
1-218-965-11
1-218-986-11
1-218-985-11
1-218-981-11
1-208-939-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
10K
560K
470K
220K
150K
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3622
R3656
R3657
R3658
R3659
1-218-949-11
1-218-990-11
1-218-977-11
1-218-953-11
1-218-960-11
RES-CHIP
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
470
0
100K
1K
3.9K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
R3309
R3310
R3311
R3312
R3313
1-218-990-11
1-218-965-11
1-218-965-11
1-218-946-11
1-218-990-11
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
0
10K
10K
270
0
5%
5%
5%
1/16W
1/16W
1/16W
R3660
R3701
R3702
R3704
R3705
1-218-957-11
1-218-961-11
1-218-961-11
1-218-941-11
1-218-981-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
4.7K
4.7K
100
220K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
6-29
Remarks
VC-254
Ref. No.
Part No.
Description
Part No.
Description
R3706
R3708
R3712
R3713
R3714
1-218-954-11
1-218-954-11
1-218-936-11
1-218-935-11
1-218-936-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.2K
1.2K
39
33
39
5%
5%
5%
5%
5%
Remarks
1/16W
1/16W
1/16W
1/16W
1/16W
Ref. No.
R4436
R4447
R4448
R4449
R4450
1-218-961-11
1-218-971-11
1-218-971-11
1-218-972-11
1-216-789-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
4.7K
33K
33K
39K
2.2
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3715
R3716
R3717
R3721
R3722
1-218-935-11
1-218-936-11
1-218-935-11
1-208-715-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
33
39
33
22K
1K
5%
5%
5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4451
R4452
R4453
R4502
R4503
1-216-789-11
1-216-789-11
1-218-989-11
1-218-990-11
1-218-977-11
METAL CHIP
METAL CHIP
RES-CHIP
SHORT
RES-CHIP
2.2
2.2
1M
0
100K
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
R3724
R3726
R3727
R3728
R3729
1-218-953-11
1-218-965-11
1-218-953-11
1-218-953-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
10K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4507
R4508
R4511
R4512
R4514
1-218-953-11
1-218-985-11
1-218-953-11
1-218-961-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
470K
1K
4.7K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3730
R3903
R3904
R3905
R3908
1-218-953-11
1-218-971-11
1-218-961-11
1-218-971-11
1-218-966-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
33K
4.7K
33K
12K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4520
R4521
R4522
R4523
R4524
1-218-953-11
1-218-965-11
1-218-965-11
1-218-985-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
10K
10K
470K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3909
R3911
R3912
R3913
R3916
1-218-989-11
1-208-715-11
1-218-947-11
1-218-953-11
1-218-949-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1M
22K
330
1K
470
5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4526
R4527
R4530
R4801
R4802
1-218-985-11
1-218-977-11
1-218-949-11
1-218-973-11
1-218-961-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
100K
470
47K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3917
R3918
R3919
R3920
R3921
1-218-979-11
1-218-979-11
1-218-950-11
1-218-963-11
1-218-949-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
150K
150K
560
6.8K
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4803
R4805
R4806
R4807
R4808
1-218-977-11
1-218-953-11
1-218-953-11
1-218-957-11
1-218-990-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
100K
1K
1K
2.2K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R3922
R3923
R3924
R3936
R3939
1-218-972-11
1-218-949-11
1-218-949-11
1-218-955-11
1-218-990-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
39K
470
470
1.5K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R4809
R4810
R4811
R4812
R4813
1-218-953-11
1-218-953-11
1-218-977-11
1-218-953-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
100K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3940
R3943
R4401
R4402
R4405
1-218-990-11
1-218-966-11
1-218-973-11
1-218-983-11
1-218-977-11
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
12K
47K
330K
100K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R4814
R4815
R4816
R4817
R4818
1-218-965-11
1-218-965-11
1-218-953-11
1-218-954-11
1-218-954-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
1K
1.2K
1.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4407
R4408
R4409
R4410
R4411
1-218-949-11
1-217-671-11
1-217-671-11
1-217-671-11
1-216-023-00
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
1
1
1
82
5%
5%
5%
5%
5%
1/16W
1/10W
1/10W
1/10W
1/10W
R4819
R4820
R4821
R4822
R4823
1-218-954-11
1-218-977-11
1-218-985-11
1-218-973-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.2K
100K
470K
47K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4414
R4416
R4417
R4423
R4424
1-218-946-11
1-218-961-11
1-208-707-11
1-218-990-11
1-218-971-11
RES-CHIP
RES-CHIP
METAL CHIP
SHORT
RES-CHIP
270
4.7K
10K
0
33K
5%
5%
0.5%
1/16W
1/16W
1/16W
5%
1/16W
R4824
R4829
R4830
R4832
R4833
1-218-958-11
1-218-953-11
1-218-953-11
1-218-989-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
2.7K
1K
1K
1M
470K
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4425
R4426
R4427
R4428
R4429
1-218-959-11
1-218-977-11
1-218-965-11
1-217-671-11
1-217-671-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
3.3K
100K
10K
1
1
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/10W
1/10W
R4834
R4835
R4836
R4840
R4855
1-218-985-11
1-218-989-11
1-218-989-11
1-218-953-11
1-218-977-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470K
1M
1M
1K
100K
0.5%
0.5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4430
R4431
R4432
R4434
R4435
1-218-985-11
1-218-967-11
1-218-973-11
1-218-965-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
15K
47K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4861
R4862
R4863
R4864
R4867
1-218-953-11
1-218-953-11
1-218-973-11
1-218-986-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
47K
560K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
6-30
Remarks
VC-254
Ref. No.
Part No.
Description
R4868
R4869
R4872
R4873
R4876
1-218-985-11
1-218-985-11
1-218-977-11
1-218-977-11
1-219-570-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
470K
100K
100K
10M
5%
5%
5%
5%
5%
Remarks
1/16W
1/16W
1/16W
1/16W
1/16W
Ref. No.
R5717
1-218-953-11 RES-CHIP
Part No.
Description
1K
Remarks
R5718
1-218-967-11 RES-CHIP
15K
R5718
1-218-973-11 RES-CHIP
47K
R4878
R4882
R4883
R4884
R4885
1-218-977-11
1-218-949-11
1-218-985-11
1-218-990-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
RES-CHIP
100K
470
470K
0
1K
5%
5%
5%
1/16W
1/16W
1/16W
R5719
1-218-975-11 RES-CHIP
68K
R5719
1-218-976-11 RES-CHIP
82K
5%
1/16W
R4886
R4887
R4888
R4897
R4898
1-218-953-11
1-218-977-11
1-218-977-11
1-218-953-11
1-218-989-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
100K
100K
1K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5720
R5721
R5724
R5725
R5730
1-218-979-11
1-218-973-11
1-218-985-11
1-218-985-11
1-218-952-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
150K
47K
470K
470K
820
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4899
R4901
R4902
R4903
R4904
1-218-965-11
1-218-953-11
1-218-986-11
1-218-990-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
RES-CHIP
10K
1K
560K
0
100K
5%
5%
5%
1/16W
1/16W
1/16W
R5731
R5732
R5733
R5742
R5743
1-218-949-11
1-218-949-11
1-218-985-11
1-218-965-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470
470
470K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
5%
1/16W
R4906
R4908
R4910
R4911
R4912
1-218-990-11
1-218-977-11
1-218-977-11
1-218-977-11
1-218-961-11
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
100K
100K
100K
4.7K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R5744
R5745
R5746
R5747
R5801
1-218-973-11
1-218-965-11
1-218-965-11
1-218-973-11
1-218-971-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
47K
10K
10K
47K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4913
R4915
R4916
R4917
R4918
1-218-957-11
1-218-961-11
1-218-961-11
1-218-953-11
1-218-957-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
4.7K
4.7K
1K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5802
R5803
R5805
R5806
R5807
1-218-968-11
1-218-957-11
1-218-961-11
1-218-965-11
1-218-963-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
18K
2.2K
4.7K
10K
6.8K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4920
R4921
R4922
R4923
R4924
1-218-965-11
1-218-965-11
1-218-973-11
1-218-973-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
47K
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5809
R5814
R5815
R5816
R5817
1-218-957-11
1-218-963-11
1-218-953-11
1-218-953-11
1-218-957-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
6.8K
1K
1K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4925
R4926
R4927
R4928
R4929
1-218-985-11
1-218-985-11
1-218-973-11
1-218-977-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
470K
47K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5818
R5819
R5820
R5821
R5822
1-218-957-11
1-208-910-11
1-220-193-81
1-208-910-11
1-220-193-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
9.1K
7.5K
9.1K
7.5K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
47K
47K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1-218-954-11
1-218-990-11
1-218-990-11
1-218-954-11
1-218-963-11
RES-CHIP
SHORT
SHORT
RES-CHIP
RES-CHIP
1.2K
0
0
1.2K
6.8K
1/16W
1-218-977-11
1-218-973-11
1-218-973-11
1-218-977-11
1-218-977-11
R5823
R5824
R5825
R5826
R5827
5%
R4930
R4931
R4932
R4935
R4936
5%
5%
1/16W
1/16W
R4943
R4944
R5707
R5708
R5709
1-218-953-11
1-218-953-11
1-218-953-11
1-218-953-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5828
R5829
R5831
R5834
1-218-963-11
1-218-971-11
1-218-990-11
1-218-965-11
RES-CHIP
RES-CHIP
SHORT
RES-CHIP
6.8K
33K
0
10K
5%
5%
1/16W
1/16W
5%
1/16W
R5710
R5711
R5712
R5714
R5715
1-218-965-11
1-218-941-11
1-218-941-11
1-218-973-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
100
100
47K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
5%
1/16W
(TRV330/TRV530)
5%
1/16W
(TRV230)
5%
1/16W
(TRV330/TRV530)
5%
1/16W
(TRV330/TRV530)
5%
1/16W
(TRV230)
< COMPOSITION CIRCUIT BLOCK >

RB4402
RB4501
RB4502
RB4801
RB4803
6-31
1-234-381-21
1-234-381-21
1-234-381-21
1-234-375-21
1-234-383-21
RES, NETWORK 100KX4

RES, NETWORK 100KX4
RES, NETWORK 100KX4
RES, NETWORK 1KX4
RES, NETWORK 470KX4
(1005)
(1005)
(1005)
(1005)
(1005)
VC-254
Ref. No.
Part No.
Description
1-234-383-21
1-234-375-21
1-234-381-21
1-234-378-21
1-234-381-21
RES, NETWORK 470KX4

RES, NETWORK 1KX4
RES, NETWORK 100KX4
RES, NETWORK 10KX4
RES, NETWORK 100KX4
(1005)
(1005)
(1005)
(1005)
(1005)
RB4903 1-234-381-21 RES, NETWORK 100KX4
(1005)
RB4804
RB4812
RB4814
RB4817
RB4818
Remarks
Ref. No.
Part No.
Description
3-066-676-01
3-987-015-01
A-7033-740-A
A-7096-387-A
X-3949-376-3
CD-ROM SPVD-004 (P)(TRV330:E/TRV530:E)

BELT (S), SHOULDER
MEMORY STICK (TRV330/TRV530)
NP-FM30 BATTERY PACK
CAP (N) ASSY, LENS
Remarks
< TRANSFORMER >

T1301
1-435-252-21 TRANSFORMER, DC-DC CONVERTER

< VIBRATOR >
X1501 1-767-586-21 VIBRATOR, CRYSTAL (27MHz)

X3301 1-767-399-11 VIBRATOR, CRYSTAL (24.576MHz)
X4801 1-767-980-21 VIBRATOR, CERAMIC (20MHz)
X4802 1-760-458-21 VIBRATOR, CRYSTAL (32.768KHZ)
X4901 1-760-655-41 VIBRATOR, CRYSTAL (20MHz)
************************************************************
ACCESSORIES
***********
0
0
0
0
0
0
0
0
0
1-475-141-61 REMOTE COMMANDER (RMT-814)

1-475-599-11 ADAPTOR, AC (AC-L10A)
(TRV230:US,CND,E,HK,AR/TRV330:US,CND,E,HK,JE,BR/
TRV530:US,CND,E,HK,AR)
1-475-599-71 ADAPTOR, AC (AC-L10A)
(TRV230:KR/TRV330:KR/TRV530:KR)
1-569-007-11 ADAPTOR, CONVERSION 2P
(TRV330:JE/TRV530:JE)
1-569-008-21 ADAPTOR, CONVERSION 2P
(TRV230:E,HK/TRV330:E,HK/TRV530:E,HK,AR)
1-757-293-11 CORD, CONNECTION (USB 5P)(1.5m)
(TRV330/TRV530)
1-765-080-11 CORD, CONNECTION (AV CABLE) (1.5m)
1-769-608-11 CORD, POWER(TRV230:E/TRV330:E/TRV530:E)
1-776-985-11 CORD, POWER
(TRV230:KR/TRV330:KR/TRV530:KR)
1-783-374-11 CORD, POWER
(TRV230:HK/TRV330:HK/TRV530:HK)
1-783-952-11 CORD, POWER (TRV230:AR/TRV530:AR)
1-790-107-22 CORD, POWER
(TRV230:US,CND/TRV330:US,CND/TRV530:US,CND)
1-790-732-11 CORD, POWER (TRV330:JE/TRV530:JE)
3-065-262-12 MANUAL, INSTRUCTION (ENGLISH)
(TRV230:US,CND,E,HK/TRV330:US,CND,E,HK,JE/
TRV530:US,CND,E,HK,JE)
3-065-262-22 MANUAL, INSTRUCTION (FRENCH)
(TRV230:CND/TRV330:CND/TRV530:CND)
3-065-262-32 MANUAL, INSTRUCTION
(SPANISH/PORTUGUESE)
(TRV230:E,AR/TRV330:E,JE/TRV530:E,KR,JE,AR)
3-065-262-42 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE)
(TRV230:E,HK/TRV330:E,HK/TRV530:E,HK)
3-065-262-52 MANUAL, INSTRUCTION (ARABIC)
(TRV230:E/TRV330:E/TRV530:E)
3-065-262-62 MANUAL, INSTRUCTION (KOREAN)
(TRV230:KR/TRV330:KR,JE/TRV530:KR,JE)
3-066-326-01 SPVD-004 (TRV330:US,CND,E,HK,KR,JE,BR/
TRV530:US,CND,E,HK,KR,JE,AR)
6-32E
Note :
specified.
Note :
pour la scurit.
OPTICAL
AXIS FRAME
294
Take a copy of OPTICAL AXIS

FRAME with a clear sheet for use.
FOR
CAMERA COLOR REPRODUCTION ADJUSTMENT
Take a copy of CAMERA COLOR

REPRODUCTION FRAME with
a clear sheet for use.
295
9-929-859-11
Sony EMCS Co.
296
2005F1600-1
2005.06
Published by DI Technical Support Department
RMT-814
US Model
Canadian Model
E Model
Hong Kong Model
Korea Model
SERVICE MANUAL
2001. 07
Tourist Model
DCR-TRV330/TRV530
Argentina Model
DCR-TRV230/TRV530
Brazilian Model
SUPPLEMENT-1
DCR-TRV330
File this supplement-1 with the Service Manual.

(EVB11596)(EVB11956)
Subject LCD panel (2.5-inch type) is changed. As the

result the following items are changed at the
same time.
1. Cold cathode fluorescent tube is changed
2. PD-138 board is changed to PD-139 board
3. VC-254 board is changed
4. Adjustment method is changed
CD-ROM (SPVD-004) is changed
This Supplement-1 supports replacement of LCD panel (2.5-inch type)(DCR-TRV230/TRV330
models. TRV530 has not relation with this supplement. Because it uses 3.5-inch LCD) from
the LCD type SH to the LCD type SO.
To check the LCD type, refer to section 1-5. LCD Type Check of 5. Adjustment. (See page 6.)
The above described parts do not have compatibility each other. Be sure to replace all of the
related parts at the same as listed and perform the adjustment.
Main differences are shown below.
LCD TYPE SH for TRV230/TRV330
LCD TYPE SO for TRV230/TRV330
LCD PANEL

1-803-852-21

8-753-050-65
Cold Cathode
Fluorescent Tube
1-518-725-21
1-518-725-11
PD-138 Board
PD-139 Board
VC-254 Board
A-7074-646-A (TRV230/TRV330)
A-7074-786-A (TRV230/TRV330)
A-7096-436-A (TRV230)
A-7096-438-A (TRV330)
A-7096-436-B (TRV230)
A-7096-438-B (TRV330)
SECTION 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
: Added portion.
LCD Type
LCD Type SH for TRV230/TRV330
: Changed portion.
: Deleted portion.
LCD Type SO for TRV230/TRV330
VC-254 BOARD (18/18)

< LOCATION H-9 to J-10 >
VC-254 BOARD (18/18)

< LOCATION H-9 to J-10 >
R1370
8.2k: DCR-TRV530
12k: DCR-TRV230/TRV330
R1319
47k
-2.2
R1369
100k
D1306
1SS383(T5RSONY1)
4-49
R1370
*
C1337
4.7u
F
D1305
*
XX
R1356
47
Q1331
FMMT717TA
.9
1.55
Q1324
*
R1337
*
R1362 C1322
100k
10u
0.5%
4V
1.3
RP_4.75V
6
R1341
*
R1342
*
Q1330
*
XX
6
C1355
*
R1343
*
Q1331,1332
D1.5V REG
1.56V
Q1324,1330
PANEL-15.3V REG
IC1304
PANEL_-15.3V_REG
PANEL_-15.3V
1.5V REG
R1363
3900 0.5%
PANEL_-15.3V
4-50
C1342
XX
VC-254 BOARD (18/18)

< LOCATION G-15 to H-16 >
PANEL_-15.3V_REG
1.5V REG
R1335
*
L1312
Q1302
CPH6702-TL
SWITCHING
Q1324,1330
PANEL-15.3V REG
IC1304
R1363
3900 0.5%
6
6
Q1332
2SC4738F-Y/GR(TPL3)
1.3
Q1331,1332
D1.5V REG
1.56V
-2.2
R1320
22k
C1328
XX
D1301
XX
VC-254 BOARD (18/18)

< LOCATION G-15 to H-16 >
Q1331
FMMT717TA
.9
1.55
R1319
47k
C1362
2.2u
F
C1338
4.7u
F
D1305
XX
C1342
*
Q1332
2SC4738F-Y/GR(TPL3)
L1312
R1369
100k
C1359
4.7u
F
C1328
*
D1301
*
Q1302
CPH6702-TL
SWITCHING
Q13
DTC144
EMERGE
DETECT
C1362
2.2u
F
C1338
4.7u
F
R1370
D1306
1SS383(T5RSONY1)
R1320
22k
Q13
DTC144
EMERGE
DETECT
C1359
4.7u
F
13.5
Q1333
2SC4738F-Y/GR(TPL3)
EP 13.3V REG
14.3
D1302
1SS383(T5RSONY1)
T1301
CONVERTER
TRANSFORMER
12.8
C1337
4.7u
F
12.8
13.5
Q1333
2SC4738F-Y/GR(TPL3)
EP 13.3V REG
14.3
D1302
1SS383(T5RSONY1)
T1301
CONVERTER
TRANSFORMER
R1335
XX
Q1324
XX
R1342
XX
Q1330
XX
R1337
XX
R1356
47
C1355
XX
R1343
XX
R1362 C1322
100k
10u
0.5%
4V
EP_13.3V
RP_4.75V
R1341
XX
EP_13.3V
L1320
4.7uH
L1320
4.7uH
*MARKED:MOUNT TABLE
REF.NO.
DCR-TRV230/
TRV330
DCR-TRV530
C1328
C1342
C1355
D1301
D1305
Q1324
Q1330
R1335
R1337
R1341
R1342
R1343
R1370
0.01u
0.1u
2.2u
1SS357
(T3SONY1)
1SS357
(T3SONY1)
2SC4738F-Y
UPO44O1OO8SO
100k
100k
4.7k
220k
68k
12k
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
8.2k
: Added portion.
SH_R
SH_G
VDD
C5511
560p
CH
25
OSCO
XSTBY
0
VST
1.4
VCK
2.6
EN
2.8
IC5502
DWN
TIMING GENERATOR
WIDE
0.1
2.8
VDD
*
HST
1.4
HCK2
R5
CN5502 10P
XHD
XHD-OUT
R5553
47k
CN5502 10P
VB
XVD_OUT
VG
PSIG
VR
MAKER_CHECK
XHD
XHD_OUT
GND
0
1.4
2.6
2.8
0.1
2.8
VB
XVD_OUT
VG
CPC
PSIG
(FOR CHECK)
VR
MAKER_CHECK
XVD-OUT
R5553
XHD
XHD-OUT
10 GND
CPC
(FOR CHECK)
XHD
XHD_OUT
GND
10 GND
*MARKED:MOUNT TABLE
REF.NO.
DCR-TRV230/
TRV330
DCR-TRV530
0
1.4
R5
< LOCATION J-15 >
< LOCATION J-15 >
18
17
18
HST
HCK2
24
26
23
27
22
28
OSCI
2.8
29
XC.SAVE
1.4
30
RPD
1.4
XP.SAVE
XC.SAVE
31
TEST
2.8
32
VSS
1.4
33
SHA
2.8
SH4
34
SHB
0.9
35
SHG
0.9
SH3
SH2
36
IC5502
17
IC5502
CXD3516R-T4
21
TIMING GENERATOR
50V
CH
L5505
20
DWN
WIDE
C5516
R5510
68k
19
IC5502
0.9
SH1
2.8
EN
C5515
1000p
SL
R5511
1M
SHR
XSTBY
2.8
XSH.SAVE
R55
27
R5507
47k
D5502
1T369-01-T8A
XCLR
OSCI
OSCO
VST
VCK
24
25
23
26
22
27
21
28
20
29
R5512
100k
C5512
0.1u
B
R5508
68k
R5509
22k
19
30
XC.SAVE
1.4
31
RPD
1.4
32
XVD-OUT
0.9
2.8
XP.SAVE
XC.SAVE
33
TEST
2.8
34
VSS
1.4
35
SHA
2.8
42
2.8
C5511
560p
CH
SH4
36
SHB
0.9
SH3
43
C5516
100p
L5505 50V
6.8uH CH
R5510
68k
0.9
SH2
44
C5515
1000p
SL
R5511
1M
SHG
2.8
D5502
1T369-01-T8A
SHR
0.9
R_IN
SH4
R55
27
SH4
4-95,
4-96
R5512
100k
XCLR
2.8
SH1
R5509
22k
G_IN
< LOCATION F-10, I-9 >
C5512
0.1u
B
R5507
47k
45
1.8
B_IN
SH_G
1.8
C5507
0.01u
XP.SAVE
SH_R
< LOCATION F-10, I-9 >

R5508
68k
1.8
C5506
0.01u
LPF_ADJ
XSH.SAVE
R_IN
2.8
XP.SAVE
C5505
0.01u
46
G_IN
TRAP_ADJ
47
B_IN
1.2
R5503
Vcc1
2.8
XP.SAVE
2.8
R5558
XX
C5503
0.1u
R5502
B
XX
0.9
1.8
LPF_ADJ
R5557
0
2.8
1.8
C5507
0.01u
42
1.8
C5506
0.01u
43
2.8
XP.SAVE
C5505
0.01u
44
1.2
R5503
82k
45
C5503
0.1u
R5502
B
XX
TRAP_ADJ
46
R5558
XX
2.8
Vcc1
47
2.8
48
2.8
48
PD-139 BOARD (1/2)

< LOCATION D-5 >
PD-139 BOARD (1/2)(DCR-TRV530)

< LOCATION D-5 >
R5557
0
: Deleted portion.
2.8
LCD Type
: Changed portion.
R5553
C5516
IC5502
L5505
R5503
82P
CXD3512R-T4
27uH
100k
22k
100P
CXD3516R-T4
6.8uH
82k
47k
: Added portion.

< LOCATION F-15 >
24P
CN5501
24
TEST1
24
TEST1
23
COM
23
COM
22
VST
22
VST
21
VCK
21
VCK
20
EN
20
EN
19
DWN
19
DWN
18
VDD
18
VDD
17
VSS
17
VSS
16
VDOG
16
VDOG
15
VVSSG
15
VVSSG
14
CS
14
CS
13
WIDE
13
WIDE
12
HST
12
HST
11
REF
11
REF
10
SOUT
10
SOUT
CRext
CRext
HCK2
HCK2
HCK1
HCK1
LCD901
3.5 INCH
COLOR
LCD UNIT
PSIG
PSIG
RGT
RGT
TEST2
TEST2

< LOCATION H-5 >
Q5601
UN9213J-(K8).SO
INV.
A
GND
INH
CH1
VEE
CH0
COM
2.8
Q5601
UN9213J-(K8).SO
INV.
VCC
A
GND
2.8
2.8
IC5601
SELECT SWITCH
1.4
R5614
15k
1.4
CH1
VEE
1.4
CH0
INH
IC5601
TC7W53FU(TE12R)
R5609
10k
SELECT SWITCH
VCC
COM
IC5601
LCD901
2.5/3.5 INCH
COLOR
LCD UNIT
PD-139 BOARD (2/2)

< LOCATION H-5 >
1.4
IC5601
TC7W53FU(TE12R)
R5609
10k
4-97
24P
4-96
PD-139 BOARD (1/2)

< LOCATION F-15 >
2.8
CN5501
: Deleted portion.
LCD Type
: Changed portion.
R5614
10k:DCR-TRV230/TRV330
15k:DCR-TRV530
SECTION 5. ADJUSTMENTS
LCD Type
5-3
: Changed portion.
1.
1.
1-1.
Adjusting items when replacing main

parts and boards.
1-1.
Adjusting items when replacing main

parts and boards.
*1: When replacing the drum assy or mechanism deck, reset

the data of page: 2, address: A2 to A4 to 00. (Refer to
Record of Use check of 5-4. SERVICE MODE)
*3: DCR-TRV230/TRV330 (LCD TYPE SH)
*4: DCR-TRV530
*4: DCR-TRV530
DCR-TRV230/TRV330 (LCD TYPE SO)
*5: CF-079 board (Part No. suffix: 12 or later)
PD-138 board: DCR-TRV230/TRV330
1-2.
5-10

PD-138 board: DCR-TRV230/TRV330 (LCD TYPE SH)
DCR-TRV230/TRV330 (LCD TYPE SO)
INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE 1-2.

DATA
INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE
DATA
4. D Page Table
4. D Page Table
Address
Address
Note: XX / YY
XX : DCR-TRV230/TRV330
YY : DCR-TRV530
Note: XX / YY / ZZ
XX : DCR-TRV230/TRV330 (LCD TYPE SH)
YY : DCR-TRV530 (LCD TYPE SO)
ZZ : DCR-TRV230/TRV330 (LCD TYPE SO)
Remark
Initial value
99
37
Contrast adj. (EVF)
9A to 9F
Fixed data-1
A0
Fixed data-2
A1
A2
80
VCO adj. (LCD)
A3
70
A4
80/26
V-COM adj. (LCD)
A5
2B/B3
RGB AMP adj.(LCD)
A6
00/09
Black limit adj. (LCD) (TRV530)
A7
B5/41
COM AMP adj. (LCD)
(TRV230,TRV330)
PSIG gray adj. (LCD) (TRV530)
A8
80
A9
80
AA
3E/1A
Contrast adj. (LCD)
AB
00/4A
Center levei adj. (LCD) (TRV530)
AC
Fixed data-2
AD
AE
Fixed data-1
AF
Fixed data-2
B0 to FF
Fixed data-1
Remark
Initial value
99
37
Contrast adj. (EVF)
9A to 9F
Fixed data-1
A0
77/71/80 Fixed data
A1
A7/82/A2
A2
80
VCO adj. (LCD)
A3
70
A4
80/26/26 V-COM adj. (LCD)
A5
2B/B3/B3 RGB AMP adj.(LCD)
A6
00/09/09 Fixed data (LCD TYPE SH)
Black limit adj. (LCD TYPE SO)
A7
B5/41/41 COM AMP adj. (LCD TYPE SH)
PSIG gray adj. (LCD TYPE SO)
A8
80
A9
80
AA
3E/1A/1A Contrast adj. (LCD)
AB
00/4A/4A Fixed data (LCD TYPE SH)
Center level adj. (LCD TYPE SO)
AC
0F/0E/0E Fixed data
AD
15/0F/11
AE
Fixed data-1
AF
1F/DF/5F Fixed data
B0 to FF
Fixed data-1
Table. 5-1-3.

Table. 5-1-3.
: Added portion.
LCD Type
1-5.
: Changed portion.
1-5.
Note 1: The back light (fluorescent tube) is driven by a high voltage

AC power supply. Therefore, do not touch the back light holder
to avoid electrical shock.
Note 2: When replacing the LCD unit, be careful to prevent damages
Note 3: Set the LCD BRIGHT (Menu display) to the center.
Set the LCD COLOR (Menu display) to the center.
Note 4: PD-138 board: DCR-TRV230/TRV330
Note 4: PD-138 board: DCR-TRV230/TRV330 (LCD TYPE SH)

PD-139 board: DCR-TRV230/TRV330 (LCD TYPE SO)
DCR-TRV530 (LCD TYPE SO)
[LCD Type Check]

[LCD Type Check]
By measuring the resistor value between Pin 6 of CN5502 By measuring the resistor value between Pin 6 of CN5502
and GND, the type of LCD can be discriminated.
and GND, the type of LCD can be discriminated.
5-29
Resistor value 1.0k

LCD type 2.5 LCD TYPE SH
(61k)
PD board PD-138
DCRTRV230/TRV330
47k
3.5 LCD TYPE SO
(123k)
PD-139
TRV530
Table 5-1-12.
Resistor value 1.0k

LCD type 2.5 LCD
TYPE SH (61k)
PD board PD-138
DCRTRV230/TRV330
22k
2.5 LCD
TYPE SO (61k)
PD-139
TRV230/TRV330
Table 5-1-12.
DCR-TRV230/TRV330:
1. VCO adjustment
5. V-COM adjustment
LCD TYPE SH:
1. VCO adjustment
5. V-COM adjustment
DCR-TRV530:
1. VCO adjustment
6. V-COM adjustment
LCD TYPE SO:

1. VCO adjustment
6. V-COM adjustment
7. White balance adjustment Changed
47k
3.5 LCD
TYPE SO (123k)
PD-139
TRV530
: Added portion.
LCD Type

0. LCD Initial Data Input
(DCR-TRV230/TRV330)
Mode
Signal
VTR stop
No signal
Adjustment Page
Adjustment Address
D
A0, A1, A4 to A7, AA to AC, AF
Note: Refer to LCD type check for the discrimination of the LCD
type.
Adjusting method:
2) Select page: D, and input the data in the following table.
Note: Press the PAUSE button of the adjustment remote
commander each time to set the data.
3)
Address
5-29
A0
A1
A4
A5
A6
Data
LCD TYPE SH LCD TYPE SO
77
80
A7
A2
80
26
2B
B3
00
09
A7
B5
41
AA
AB
3E
00
1A
4A
AC
AF
0F
1F
0E
5F
*1: LCD TYPE SH

*2: LCD TYPE SO
Remark
Fixed data
Fixed data
V-COM adj.
RGB AMP adj.
Fixed data (*1)
Black limit adj. (*2)
COM AMP adj. (*1)
PSIG gray adj. (*2)
Contrast adj.
Fixed data (*1)
Center level adj. (*2)
Fixed data
Fixed data
: Added portion.
LCD Type

Set the VCO free-run frequency. If deviated, the LCD screen
will be blurred.
Mode
Signal
VTR stop
No signal
Measurement Point
Pin 8 of CN5502 (XHD OUT)

Frequency counter
Adjustment Page
Adjustment Address
D
A2, A3
Specified Value
f = 15734 30Hz
Adjusting method:
1
2
0
D
01
A2
3
4
D
D
A2
A2
01

Note: Refer to LCD type check for the discrimination of the LCD
type.
Adjusting method:
Procedure
Set the data.
Press PAUSE button.

named DA2.
Convert DA2 to decimal notation,

and obtain DA2. (Note)
[DCR-TRV230/TRV330]
When DA2 232
DA3= DA2+23
When DA2>232
DA3=255
[DCR-TRV530]
When DA2 246
DA3= DA2+9
When DA2>246
DA3=255
5-30
7
8
A3
DA3
01
00
Convert DA3 to a hexadecimal

number, and obtain DA3. (Note2)
button.
Procedure

[DCR-TRV230/TRV330
(LCD TYPE SH) ]
When DA2 232
DA3= DA2+23
When DA2>232
DA3=255
[DCR-TRV230/TRV330
(LCD TYPE SO)]
When DA2 235
DA3= DA2+20
When DA2>235
DA3=255
[DCR-TRV530]
When DA2 246
DA3= DA2+9
When DA2>246
DA3=255
Set the data.

(DCR-TRV530)
Set the uniformity improvement signal to an appropriate level.
Mode
Signal
VTR stop
No signal
Measurement Point

Oscilloscope
Adjustment Page
Adjustment Address
D
A7
Specified Value
A = 5.00 0.1V

(DCR-TRV530 /TRV230/TRV330 (LCD TYPE SO) )
: Added portion.
LCD Type
5-31
5-32
5-33
: Changed portion.

(DCR-TRV230/TRV330)

(DCR-TRV230/TRV330 (LCD TYPE SH) )

(DCR-TRV530)
Set the D range of the RGB decoder used to drive the LCD to
the specified value. If deviated, the LCD screen will become
blackish or saturated (whitish).

Mode
Signal
VTR stop
No signal
Measurement Point

(PSIG)
Oscilloscope
Adjustment Page
Adjustment Address
D
A5
Specified Value
A = 7.58 0.05V
Specified Value
DCR-TRV230/TRV330:
A = 7.58 0.05V
DCR-TRV530:
A = 7.52 0.05V

(DCR-TRV530)
Set the dynamic range of the LCD driver to an appropriate level.
If deviated, the LCD screen will become blackish or saturated
(whitish).


(DCR-TRV230/TRV330)
Set the level of the VIDEO signal for driving the LCD to the
specified value. If deviated, the screen image will be blackish


(DCR-TRV530)
Set the level of the VIDEO signal for driving the LCD to the
specified value. If deviated, the screen image will be blackish
Mode
VTR stop

Signal
Measurement Point
No signal
(PSIG)
Adjustment Page
Oscilloscope
D
Adjustment Address
Specified Value
AA
A = 2.76 0.07V

(DCR-TRV530)
Set the video signal center level of LCD panel to an appropriate
level.
Specified Value
DCR-TRV230/TRV330:
A = 2.80 0.07V
DCR-TRV530:
A = 2.76 0.07V

: Added portion.
LCD Type
5-34
: Changed portion.

(DCR-TRV230/TRV330)
Set the common electrode drive signal level of LCD to the
specified value.


Set the DC bias of the common electrode drive signal of LCD
to the specified value.
If deviated, the LCD display will move, producing flicker and
conspicuous vertical lines.
Mode
Signal
VTR stop
No signal
Measurement Point
Check on LCD display
Adjustment Page
Adjustment Address
D
A4
Specified Value
The brightness difference between the

section A and section B is minimum.

[DCR-TRV230/TRV330]
RGB AMP Adjustment
Contrast Adjustment
COM AMP Adjustment
[DCR-TRV530]
RGB AMP Adjustment
Contrast Adjustment

Adjusting method:
Adjusting method:
1
2
0
D
01
A4
A4
A4
01
01
00
Procedure
[LCD TYPE SH]

RGB AMP Adjustment
Contrast Adjustment
COM AMP Adjustment
[LCD TYPE SO]
RGB AMP Adjustment
Contrast Adjustment
Set the data.

[DCR-TRV230/TRV330]
[DCR-TRV530]
The data should be 00 to 3F
1
2
0
D
01
A4
[DCR-TRV230/TRV330]
[DCR-TRV530]
Press PAUSE button.
A4
A4
Set the data.
01
10
01
Procedure
Set the data.
[LCD TYPE SH]
[LCD TYPE SO]
The data should be 00 to 3F.
[LCD TYPE SH]
[LCD TYPE SO]
Press PAUSE button.
00
Set the data.
SECTION 6. REPAIR PARTS LIST

6-1. EXPLODED VIEWS
LCD Type
: Changed portion.

Ref. No.
6-2
6-6
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
56
A-7096-436-A VC-254 (BNA) BOARD, COMPLETE

(SERVICE)(TRV230)
56
A-7096-436-B VC-254 (BNS) BOARD, COMPLETE

(SERVICE)(TRV230)
56
A-7096-438-A VC-254 (BFNA) BOARD, COMPLETE

(SERVICE)(TRV330)
56
A-7096-438-B VC-254 (BFNS) BOARD, COMPLETE

(SERVICE)(TRV330)
56
A-7096-439-A VC-254 (BFNS) BOARD, COMPLETE

(SERVICE)(TRV530)
56
A-7096-439-A VC-254 (BFNS) BOARD, COMPLETE

(SERVICE)(TRV530)

(TRV230/TRV330)

(TRV230/TRV330)
255
3-065-368-01 HOLDER (2), LCD
255
3-065-368-01 HOLDER (2), LCD
256
256
A-7074-786-A PD-139 (X6) BOARD, COMPLETE
256
A-7074-696-A PD-138 BOARD, COMPLETE
0 ND901 1-518-725-21 TUBE, FLUORESCENT,COLD CATHODE

0 D902
1-518-721-11 LIGHT, BACK
LCD901 1-803-852-21 INDICATOR MODULE LIQUID CRYST
0 ND901 1-518-725-11 TUBE, FLUORESCENT,COLD CATHODE

0 D902
1-518-721-11 LIGHT, BACK
LCD901 8-753-050-65 INDICATOR MODULE LIQUID CRYST
Note :
specified.

LCD Type
: Added portion.

Ref. No.
Part No.
Note :
pour la scurit.
Description
: Deleted portion.

Remarks
Ref. No.
Part No.
Description
Remarks

(TRV230/TRV330)
***********************************
6-18

***********************************

***********************************
A-7074-786-A PD-139 BOARD, COMPLETE
(TRV230/TRV330)
***********************************
6-19
< CAPACITOR >
C5516
< CAPACITOR >
100PF
5%
50V
11
C5516
82PF
C5516
100PF
5%
50V
(TRV230/TRV330)
5%
50V
(TRV530)
: Added portion.
LCD Type

Ref. No.
Part No.
Description
Ref. No.
IC5502
IC5502
8-752-409-15 IC CXD3516R-T4
1-412-949-21 INDUCTOR
1-218-893-11 METAL CHIP
L5505
L5505
6.8uH
R5614
1-216-841-11 METAL CHIP
1-216-835-11 METAL CHIP
82K
0.5%
1/16W
47K
15K
5%
5%
1/16W
1/16W
A-7096-436-A VC-254 (BNA) BOARD, COMPLETE

(SERVICE)(TRV230)
************************************
A-7096-438-A VC-254 (BFNA) BOARD, COMPLETE
(SERVICE)(TRV330)
************************************
6-21
< CAPACITOR >
6-22
8-752-407-33 IC CXD3512R-T4 (TRV230/TRV330)

8-752-409-15 IC CXD3516R-T4 (TRV530)
1-412-949-21 INDUCTOR
1-412-956-21 INDUCTOR
6.8uH (TRV530)
27uH (TRV230/TRV330)
R5503
1-218-893-11 METAL CHIP
82K
R5503
1-218-895-11 METAL CHIP
100K
0.5%
1/16W
(TRV230/TRV330)
R5553
1-216-837-11 METAL CHIP
22K
5%
1/16W
(TRV230/TRV330)
R5553
1-216-841-11 METAL CHIP
47K
R5614
1-216-833-11 METAL CHIP
10K
R5614
1-216-835-11 METAL CHIP
15K
0.01uF
50V
(TRV230/TRV330)
C1342
0.1uF
C1355
2.2uF
50V
(TRV230/TRV330)
16V
(TRV230/TRV330)
< DIODE >
< DIODE >
D1301
8-719-078-02 DIODE 1SS357(T3SONY1) (TRV230/TRV330)
D1305
8-719-078-02 DIODE 1SS357(T3SONY1) (TRV230/TRV330)
< TRANSISTOR >
< TRANSISTOR >
Q1324
2SC4738F-Y/GR(TPL3)
(TRV230/TRV330)
Q1330
UP04401008S0
(TRV230/TRV330)
12
0.5%
5%
1/16W
(TRV530)
1/16W
(TRV530)
5%
1/16W
(TRV230/TRV330)
5%
1/16W
(TRV530)
A-7096-436-B VC-254 (BNS) BOARD, COMPLETE

(SERVICE)(TRV230)
************************************
A-7096-438-B VC-254 (BFNS) BOARD, COMPLETE
(SERVICE)(TRV330)
************************************
< CAPACITOR >
C1328
6-25
Remarks
< RESISTOR >
6-20
R5553
Description
< COIL >
< RESISTOR >

R5503
Part No.
< IC >
< COIL >

L5505
: Deleted portion.

Remarks
< IC >
IC5502
: Changed portion.
: Deleted portion.
LCD Type

Ref. No.
Part No.
Description

Remarks
Ref. No.
Part No.
< RESISTOR >
6-28
Description
R1335
1-218-977-11 RES-CHIP
100K
5%
1/16W
(TRV230/TRV330)
R1337
1-218-977-11 RES-CHIP
100K
5%
1/16W
(TRV230/TRV330)
R1341
1-218-961-11 RES-CHIP
4.7K
R1342
1-208-943-11 METAL CHIP
220K
5%
1/16W
(TRV230/TRV330)
0.5%
1/16W
(TRV230/TRV330)
R1343
1-208-931-11 METAL CHIP
68K
0.5%
1/16W
(TRV230/TRV330)
R1370
1-208-709-11 METAL CHIP
12K
0.5%
1/16W
(TRV230/TRV330)
R1370
1-208-909-11 METAL CHIP
8.2K
0.5%
1/16W
(TRV530)
R1370
1-208-909-11 METAL CHIP
: Added portion.
Page
Before change
Ref. No.
Part No.
Description
Remarks
< RESISTOR >
8.2K
0.5%
1/16W
: Changed portion.
After change
Remarks
Ref. No.
3-066-326-01 SPVD-004 (TRV330:US,CND,E,HK,KR,JE,BR/

TRV530:US,CND,E,HK,KR,JE,AR)
Part No.
Description
Remarks
3-066-326-01 SPVD-004
(TRV330:E,HK,KR,JE,BR/TRV530:E,HK,KR,JE,AR)
6-32E
3-066-677-01 SPVD-004 (I)
(TRV330:US,CND/TRV530:US,CND)
13
9-929-859-81
Sony EMCS Co. Kohda TEC
14
2001G1600-1
2001.7
Published by PV Customer Center
RMT-814
US Model
Canadian Model
E Model
Hong Kong Model
Korea Model
SERVICE MANUAL
Ver 1.2 2005. 06
Tourist Model
DCR-TRV330/TRV530
Argentina Model
DCR-TRV230/TRV530
Brazilian Model
DCR-TRV330
SUPPLEMENT-2
File this supplement-2 with the service manual.
Change of repair parts list
6. REPAIR PARTS LIST

6-1. EXPLODED VIEWS
Page
: Changed portion
Before change
: Added portion
After change
6-1-1. OVERALL SECTION

4
not
supplied
not
supplied
l8
l8
ita
ita
Dig
Dig
6-1
2
B
MIC901
Ref. No.
Part No.
19
3
MIC901
Description
Ref. No.
Part No.
Description
19
3-979-194-12 STRING, CAP
102
3-052-815-02 BELT (ES), GRIP

6-3
102
3-052-815-01 BELT (ES), GRIP
6-1-8. LENS, EVF SECTION

352
X-3951-248-1 IRIS FLEXIBLE, ASSY
352
1-758-555-11 IRIS (IR700)
361
X-3951-165-1 HINGE ASSY, VF
361
X-3951-165-4 HINGE ASSY, VF
6-8
9-929-859-82
Sony EMCS Co.
2005F1600-1
2005.06
Published by DI Technical Support Department

Page
: Added portion
Before change
Ref. No.
Part No.
6-32E
After change
Description
Ref. No.
ACCESSORIES
************
Part No.
Description
ACCESSORIES
************
3-979-194-12 STRING, CAP
Reverse
992985913.pdf
Revision History
History
Date
1.0
2000.12
Official Release
1.1
2001.07
Supplement-1
LCD panel (2.5-inch type) is changed. As

the result the following items are changed at
the same time.
1. Cold cathode fluorescent tube is changed
2. PD-138 board is changed to PD-139 board
3. VC-254 board is changed
4. Adjustment method is changed
CD-ROM (SPVD-004) is changed
No
1.2
2005.06
Supplement-2
Change of repair parts list
No
Contents
S.M. Rev.
issued
Ver.

Service Manual Service Manual: Digital Video Camera Recorder

Uploaded by

Copyright:

Available Formats

Service Manual Service Manual: Digital Video Camera Recorder

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual Service Manual: Digital Video Camera Recorder

Uploaded by

Copyright:

Available Formats

DCR-TRV230/TRV330/TRV530

Ver 1.2 2005. 06

For MECHANISM ADJUSTMENT, refer to the 8mm

Continued on next page

DIGITAL VIDEO CAMERA RECORDER

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT

Check the area of your repair for unsoldered or poorly-soldered

Look for parts which, through functioning, show obvious signs

Table for difference of function

a: with PC-082 board

POWER SUPPLY DURING REPAIRS 8

Quick Start Guide 1-1

Superimposing a still images in the Memory Stick on an

LCD UNIT, PD-138 BOARD (TRV230/TRV330) 2-2

OVERALL BLOCK DIAGRAM (1/5) 3-1

PRINTED WIRING BOARDS AND

4-1. FRAME SCHEMATIC DIAGRAM (1/3) 4-1

CD-315 (CCD IMAGER)

CF-079 (USER FUNCTION, EVF DRIVE)

Before starting adjustment 5-2

5-3. VIDEO SECTION ADJUSTMENT 5-38

Record of Use check 5-64

REPAIR PARTS LIST

6-1. EXPLODED VIEWS 6-1

POWER SUPPLY DURING REPAIRS

TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)

9 Pull the timing belt in the direction of

Press the cassette compartment not

0 Let your hold the cassette

When problems occur while the unit is operating, the self-diagnosis

Refer to page 10 and 11.

Service Mode Display

Order of previous errors

Switching of Backup No.

Self-diagnosis Code Table

FG fault when starting capstan.

FG fault during normal capstan

FG fault when starting drum.

PG fault when starting drum.

Non-standard battery is used.

FG fault during normal drum

Use the InfoLITHIUM battery.

Difficult to adjust focus

Zoom operations fault

Inspect the lens block focus reset sensor (Pin qd of CN1551 of

Handshake correction function does not

Inspect pitch angular velocity sensor (SE301 of SE-028/029

The following flow chart shows the disassembly procedure.

PD-138 board service position

2-2. LCD unit, PD-139 board (TRV530)

PD-139 board service position

2-3. Front panel section, SI-028/029 board

SI-028/029 board service position

2-4. Cabinet (R) section

2-15. Hinge section

2-5. CF-079 board (TRV230/TRV330)

2-6. CF-080 board (TRV530)

CF-079/080 SI-028/029 boards service position