September 2009

P320 EL 4 C P8 Software package

ALSPA 8000 - P320 EL

P8 SOFTWARE PACKAGE
Displays browser

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 2 / 23

P320 EL P8 SOFTWARE
Progiciel P8 Version > 9.01 PC et CPU protocol SNP, Serial Network Protocol for ALSPA 8000 PLC serial Power supply port in RS 422

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 3 / 23

P320 EL P8 SOFTWARE
MAIN MENU CONTROLLER SELECTION :
SHIFT - F1 ... ALSPA C80-05 SHIFT - F2 ... ALSPA C80-25 SHIFT - F3 ... ALSPA C80-35 SHIFT - F5 ... ALSPA C80-75

SELECTION OF FUNCTIONALITIES :
F1 ALSPA P8 PROGRAMMMING SOFTWARE F2 ALSPA P8 CONFIGURATION SOFTWARE F3 ... PCM DEVELOPMENT SOFTWARE (PCOP) F4 ... AXIS MODULE DEVELOPMENT SOFTWARE F5 ... OPERATOR INTERFACE UTILITIES F7 ... ALSPA P8 UTILITIES F8 ... USER MENU F9 ALSPA P8 GENERAL PARAMETERIZATION F10 ... RETURN TO DOS

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 4 / 23

P320 EL P8 SOFTWARE
Main Short Cut Keys For P8 :
ALT-H ALT-K ALT-M Interactive on line HELP, "escape" to exit List of short cut keys "ESCAPE" to exit To create or to break the communication between PC and plc monitor / online / offline/ ... If the link between pc and plc is "on line", ALT R stop or run the plc.

ALT-R

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 5 / 23

P320 EL
P8 CONFIGURATION SOFTWARE
AFTER SELECTION OF "CON FIGURATION SOFTWARE..." IN THE MAIN MEN U USIN G F2
F1 F2 F3 F7 F8 F9 F10

IN PUT/ OUTPUT CON FIGURATION

CPU CON FIGURATION

PLC TESTIN G AN D STATUS

SETTIN G OF CON SOLE PARAMETERS

PROGRAM FOLDERS

UTILITIES : TRAN SFERS, DELETIN G

PRIN TIN G FUN CTION S

PASSWORD
IF A CPU CONFIGURATION WAS PREVIOUSLY COMPLETED, PASSWORD DISABLED : THE MEMORY OF THE PROGRAMMABLE CONTROLLER MUST BE DELETED AND THE BATTERY REMOVED FOR MORE THAN AN HOUR TO RECONFIGURE "PASSWORD : ENABLED" AND ENTER THE DIFFERENT LEVELS.

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 6 / 23

P320 EL
P8 CONFIGURATION SOFTWARE
AFTER SELECTING "INPUT/ OUTPUT CONFIGURATION" USING F3 F1
RACK

F2
COPY
GO TO A CONFIGURED MODULE AND MOVE TOWARDS THE POSITION TO WHICH IT IS TO BE COPIED. THEN PRESS TO CONFIRM

F3
I/ O VIEW

F4
DELETE

F5
RECOVER

NO ACTION IN THIS VERSION

SHOWS THE HIGHEST VALUE CONFIGURED ACCORDING TO THE LOCATIONS

TO DELETE A MODULE

TO RECOVER A MODULE JUST DELETED

F1

F2

F4

F5

F6

F8

F10

ES
SELECTION OF TYPE OF MODULE (I/ O, DISCRETE, ANALOG) WITH DISPLAY OF LISTS

N80
SELECT DES MODULES N80 OR NBC WITH DISPLAY OF LISTS

PWR S
SEE ZOOM ON PWR SUPPLY MODULE

RCKSEL
DISPLAY OF LIST OF AVAILABLE BASE PLATES OR RACKS DISPONIBLES

COMM
SELECT ETHERNET OR CMM311 MODULES

OTHERS
SELECT OF MODULES PCM, HSC, EXTERN, ADC, APM, IOLINK AND IOP, WITH DISPLAY OF LISTS

ZOOM
GO TO POSITION OF A MODULE ALREADY CONFIGURED, SEEN FROM ITS DETAILED CONFIGURATION

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 7 / 23

P320 EL
P8 CONFIGURATION SOFTWARE
AFTER SELECTING "CONFIGURATION CPU" USING F2
FOR ALL KEYS THE ACTIONS ARE THE SAME AS FOR THE FIRST CONFIGURATION SCREEN

F1

TO F10

F1

F3

F4

TIME

IDSN P

LIMIT

SET CONTROLLER TIME

IDENTIFICATION OF CON TROLLER BY A N AME, ESPECIALLY USEFUL WHEN USING A P8 CONN ECTED TO SEVERAL C80- 35s AND WITH IN TER-PLC SN P COMMUN ICATION

DISPLAYS CONFIGURED DATA AN D PLC MEMORY LIMITS

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 8 / 23

P320 EL
P8 CONFIGURATION SOFTWARE

AFTER SELECTING "CONTROLLER CHECK AND STATUS" USING F3 F1 TO

F10

SAME AS FOR FIRST SCREEN F2 F3 F4 F5

RUN PLC

PASSWORD

PLC FLTS

ES FLTS

PLC MEM

CHOICE OF RUN OR STOP WITH OR WITHOUT I/ O SCANNING

4 PASSWORD LEVELS IF ENABLED IN CPU CONFIG.

DISPLAYS TABLE OF PLC FAULTS

DISPLAYS TABLE OF FAULTS ON MODULE (HARDWARE)

GIVES AMOUNT OF PROGRAM MEMORY USED AND REMAINING

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 9 / 23

P320 EL
P8 CONFIGURATION SOFTWARE
AFTER SELECTIN G "CON SOLE PARAMETERIZATION " USIN G F7 F1 TO
F1

F10 SAME AS FOR FIRST SCREEN

MODE SAME COMMAN D AS ALT M

CON N EC SELECTION SN P CON N ECTION S WITH CHOICE OF PLC IDEN TIFIER N AME TO BE PROGRAMMED 1 PC WITH P8 CAN BE CON N ECTED TO 8 PLCs ALSPA C80- 35 WITH DIFFEREN T SN P- ID, IF THE "PORT CON N ECTION " SELECTED IS : MULTIPOIN TS A TABLE SHOWS ALL THE SN P ID N AMES

PLC COM SETTIN G OF PARAMETERS OF THE CON SOLE COMMUN ICATION PORT CON N ECTED TO THE ALSPA C80- 35

FOR OFFLIN E/ MON ITOR/ ON LIN E MODE CHAN GE

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 10 / 23

P320 EL
P8 CONFIGURATION SOFTWARE

AFTE S LE TING "PR R E C OGR FOLDE S US AM R " ING F8 F1

TO F10
F2

S AMEAS FOR FIR T S R E S CEN

F3

F4

F5

F7

F8

S LE T E C

DE TE LE

AUTO

S AVE

RS E E TOR

E AS R E

LOC K

CE R ATION A NE PR W OGR AM FOLDE R ORS LE TION FR E C OM LIS OF THOS T E ALR ADY C E D E R ATE

DE TE A FOLDE LE S R FR THELIS BUT OM T C ANNOT DE TE THE LE FOLDE BE R ING WOR D ON, C KE ALLE D THE : " UR E FOLDE " C R NT R

AUTO-S LE TION E C FR LIS OF FOLDE OM T R C RS OR E PONDING TO THE ONELOADE INTO D THEC ONTR OLLE R (AFTE S LE TING R E C WITH F1)

S STHE C R NT AVE UR E FOLDE ON THEHAR R D DIS ORON THE K DIS TTE WITH THE KE APPR IATEPATH OPR A:\FOLDE NAME R

R S AL IN THE E TOR C R NT FOLDE UR E R FR THEBAC OM KUP OF THEHAR DIS OR D K DIS TTEA:\FOLDE KE R NAME

E AS STHEC R E ONTE NTS OF THE C R NT UR E PR OGR FILE AM WITHOUT E AS R ING THENAME

LOC ORUNLOC KS KS THEC R NT UR E PR OGR FOLDE TO AM R PR VE C R E NT E TAIN PR C DING EE OPE ATIONS R

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 11 / 23

P320 EL
P8 CONFIGURATION SOFTWARE
AFTER SELECTIN G "UTILITIES : TRAN SFERS, ERASE" USIN G F9 F1 TO F10 SAME AS FOR FIRST SCREEN
F1 F2 F3 F5 F10

CON

PLC

CHECK

ERASE

PROM

TRAN SFERS THE CON FIGURATION FROM THE PLC TO THE CON SOLE IN "RUN " OR "STOP" MODE

TRAN SFERS THE CON FIGURATION FROM THE CON SOLE TO THE PLC THE PLC MUST BE IN : "STOP" MODE AN D "ON LIN E" BETWEEN PLC AN D CON SOLE

COMPARISON BETWEEN THE CON FIGURATION CREATED IN THE CON SOLE AN D THE ON E EXISTIN G IN THE PLC

ERASES FROM THE CON TROLLER MEMORY WITH THE SELECTION OF ERASE : - PROGRAM

USED TO READ OR WRITE OR CHECK BETWEEN EEPROM AN D RAM MEMORIES OF THE PLC PLC IN STOP MODE

- CON FIGURATION - REFEREN CE TABLE - FORCIN G TABLE

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 12 / 23

P320 EL
P8 CONFIGURATION SOFTWARE
AFTER SELECTIN G "PRIN TIN G FUN CTION S " USIN G F10 F1 TO
F1

F10 SAME AS FOR FIRST SCREEN

PARAM

SCREEN

PRIN T

PAUSE

SAVE

SETTIN G PARAMETERS OF PRIN TER - - N O. OF LIN ES PER PAGE - ETC...

DESTIN ATION OF PRIN TIN G SCREEN : - PORT - FILE

CON FIGURATION OF PRIN T FOLDER FOR CON FIGURATION OF PLC TO PRIN TER OR TO A FILE

FOR TEMPORARY STOPPIN G DURIN G PRIN TIN G

SAVIN G OF PRIN TIN G PARAMETERS CON FIGURED PREVIOUSLY IN A PRIN T.SET FILE

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 13 / 23

P320 EL
P8 PROGRAMMING SOFTWARE
AFTER SELECTING "PROGRAMMING SOFTWARE" IN THE MAIN MENU USING F1
F1 F2 F3 F7 F8 F9 F10

TO EDIT OR TO READ THE PROGRAM

REFEREN CE TABLES

PLC TESTIN G AN D STATUS - RUN / STOP - PASSWORD - 2 FAULT TABLES . PLC

CON SOLE MODE AN D CON FIGURATION RS- 232 PORT N 0. AN D ALL ITS PARAMETERS CON N ECTION MODE - WITH 1 PLC

PROGRAM FOLDERS

UTILITIES : TRAN SFERS, ERASE - ESTABLISHES THE LIN K WITH THE PLC TO LOAD OR READ OR CHECK A FOLDER - ALLOWS ERASIN G OF PLC MEMORY - READ, WRITE, CHECK BETWEEN RAM AN D EEPROM OF THE PLC

PRIN T FUN CTION S

DISPLAYS VARIABLES OF DATA MEMORY BY TYPE WITH THEIR VALUE OR THE PERSON ALIZED TABLES FROM 1 TO 99

PROGRAM - CREATION - SELECTION - DELETION - SAVE

SETTIN G PARAMETERS OF PRIN TER PRIN TIN G

. I/ O - PLC MEMORY - WITH SEVERAL PLCs AN D SN P ID - SELECTION OF MODES SEEN BY ALT N

- RESTITUTION - ERASE - LOCKED - COPY THE WHOLE FOLDER

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 14 / 23

P320 EL
P8 PROGRAMMING SOFTWARE

AFTER SELECTING USING F1 F1 TO F10

F1

F2

F3

F4

F7

F8

F9

F10

INSERT INSERT A NEW RUNG BEFORE THE CURRENT RUNG

EDIT EDIT THE CURRENT RUNG

MODIFY WORD FOR WORD EDIT THE CURRENT RUNG (TO MODIFY OR TO REPLACE AN INSTRUCTION BY ANOTHER WITH THE SAME MEMORY LENGTH)

SEARCH SEARCH FOR A REFERENCE, NICHNAME OR INSTRUCTION. REPLACE THE FOUND TARGET WITH THE REPLACEMENT ITEM. DISPLAYS A SEARCH CONTROL WINDOW.

OPTION SETUP COIL USE CHECKING AND AUTOMATIC EDITOR OPTIONS.

GOTO GOTO A RUNG OR A BLOCK.

MORE

ZOOM ZOOM INT A BLOCK, FUNCTION BLOCK, COMMENT, OR MARKER RUNG UNDER

ACCESS FEATURES FOR EDITING GROUPS OF ENTER THE RUNG RUNGS, E.G., NUMBER OR CUT, PESTO BLOCK NAME AND THEN PRESS "GOTO"

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 15 / 23

P320 EL
P8 PROGRAMMING SOFTWARE
AFTER SELECTING "INSERTION OF A NEW RUNG ...", TO CHOICE AN INSTRUCTION F1
RELAY

F2
TMPCTR

F3
MATH

F4
RELATN

F5
BIT OP

F6
DATAMV

F7
TABLES

F8
CONVERT

F9
CONTRL

F10
OPN SP *

LIST OF INSTRUCTIONS AFTER THE ABOVE CHOICE

- +-/+-( )-(M)-(/ M)-(S)-(R)-(SM)-(RM) (VERT.) (HORIZ.) -() -() < <+ > <+ >

TMR OFDT ONDTR UPCTR DNCTR TMBASE (TIME BASE 0,1 S 0,01 S 0,001 S)

ADD SUB MUL DIV MOD SQRT TYPES : (INTEGER : INT DOUBLE INTEGER : DINT)

EQ NE GT GE LT LE RANGE TYPES : INT AND DINT

AND OR XOR NOT SHL SHR ROL ROR BITTST BITSET BITCLR BITPOS MKCOMP TYPES : WORD

MOVE BLKMOV BLKCLR SHFREG BITSEQ COMREQ TYPES : WORD AND DINT

SRH EQ SRH NE SRH GT SRH GE SRH LT SRH LE ARR MOV TYPES : . BYTE . WORD . INT . DINT

BCD - 4 INT

CALL DO IO PID ISA PID IND SFCRES END COMMNT SVCREQ MCR ENDMCR MCRN ENDMCRN JUMP LABEL JUMPN LABELN

DROITE BAS EFF CO EFF LI EFF SYM EFF INS

* OPEN SPACE : TO ALLOW RUNG MODIFICATIONS

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 16 / 23

P320 EL
P8 PROGRAMMING SOFTWARE
AFTER SELECTIN G "EDIT, READ PROGRAM" USIN G F1 F1
F1

TO

F10 THE ACTION S ARE THE SAME AS FOR THE FIRST PROGRAMMIN G SCREEN
F2 F3 F4 F7 F8 F9 F10

IN SER..

EDIT

MODIFY

SEARCH

OPTION

TO ...

OTHERS

ZOOM

IN SERTION OF A N EW SEGM EN T BEFORE THE POIN TED SEGM EN T

EDITION OF POIN TED SEGM EN T. ALL MODIFICATION S ARE AUTHORIZED

MODIFICATION OF POIN TED SEGM EN T

SEARCH IN A PROGRAM FOR

FOR THE EDITOR - CHECK M ULTIPLE

ALLOWS DIRECT POIN TIN G TO A SEGM EN T OR A BLOCK

M AN IPULATION OF SEGM EN TS OF PROGRAM S AN D POSSIBLE CHOICE BETWEEN

AFTER POSITION IN G ON : - A BLOC - AN IN STRUCTION - A COM M EN T - SEE DETAILS OF THE CON FIGURATION

- A REFEREN CE CERTAIN CON DITION S ARE OBLIGATORY : THE SIZE OF THE IN STRUCTION S M UST BE SIM ILAR (SEE CHAPTER 3- 12- 2 ALS DOC 52201) REPLACEM EN T AFTER SEARCH BY DATA OF THE SAM E TYPE - AN IN STRUCTION - AN IDEN TIFIER - A DESCRIPTION - A M EM ON IQUE

USE OF COILS - AUTOM ATICALLY IN SERT THE REFEREN CES IN THE VARIABLE DECLARATION TABLE (SEGM EN T 001)

STORAGE TO BUFFER M EM ORY OR FILES

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 17 / 23

P320 EL
P8 PROGRAMMING SOFTWARE
AFTER SELECTIN G "REFEREN CE TABLES" USIN G F2 F1
F2

TO

F10 SAME AS FOR FIRST SCREEN

IN T

DIN T

HEX

BIN

ASCII

TMCTR

MIXTE

CHGTOU

CON VERTS THE POIN TED REFEREN CE TO "SIGN ED IN TEGER" VALUE

CON VERTS THE POIN TED REFEREN CE TO "SIGN ED DOUBLE IN TEGER" VALUE

CON VERTS THE POIN TED REFEREN CE TO HEXADECIM AL VALUE

CON VERTS THE POIN TED REFEREN CE TO BIN ARY VALUE (16 BITS)

CON VERTS THE POIN TED REFEREN CE TO "ASCII CHARACTER"

CON VERTS THE POIN TED REFEREN CE TO GROUPS OF 3 CON SECUTIVE REGISTERS REPRESEN TIN G A COUN TER OR A TIM E DELAY

CALLS A PERSON ALIZED M IXED, REFEREN CE TABLE (1 TO 99)

IN SIDE A TABLE TO IN ITIALIZE OR CAN CEL FORCIN G IN AN EN TIRE TABLE

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 18 / 23

P320 EL
P8 PROGRAMMING SOFTWARE

AFTER SELECTIN G "PLC TESTIN G AN D STATUS" USIN G F3 F1

TO

F10 SAME AS FOR FIRST SCREEN

RUN

MOT PSS

DEF AP

DEF ES

MEM AP

MEM BLC

TAIL RF

CYCLE

IN "ON - LIN E" M ODE, ALLOWS THE CHOICE OF RUN OR STOP WITH OR WITHOUT I/ O SCAN N IN G

4 PASSWORD LEVELS IF EN ABLED IN THE CPU

DISPLAYS THE TABLE OF CON TROLLER FAULTS

DISPLAYS THE TABLE OF FAULTS ON M ODULE (HARDWARE)

DISPLAYS PROGRAM M EM ORY QUAN TITIES USED AN D REM AIN IN G

DISPLAYS DISTRIBUTION OF M EM ORY USED FOR THE PARTS : - PROGRAM - DECLARATION - COM M EN TS

DISPLAYS THE HIGHEST ADDRESS USED IN THE PROGRAM FOR EACH TYPE OF VARIABLE

DISPLAYS THE CYCLE TIME

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 19 / 23

P320 EL
P8 PROGRAMMING SOFTWARE
AFTER SELECTIN G "CON SOLE M ODE AN D CON FIGURATION " USIN G F7 F1 TO
F2

F10

SAME AS FOR FIRST SCREEN F3 F4 F5

MODE

CON N EX

CON AP

DISPLAY MODE

SAME AS COMMAN D ALT M

SELECTION SN P CON N ECTION S WITH CHOICE OF PLC IDEN TIFIER N AME TO BE PROGRAMMED 1 PC WITH P8 CAN BE CON N ECTED TO 8 PLCs ALSPA C80- 35 WITH DIFFEREN T SN P ID, IF THE "PORT CON N ECTION " SELECTED IS : MULTIPOIN TS. A TABLE SHOWS ALL THE SN P ID N AMES

SETTIN G OF PARAMETERS OF THE CON SOLE SN P COMMUN ICATION PORT CON N ECTED TO THE ALSPA C80- 35

SELECTION OF DIFFEREN T DISPLAY MODES ON THE SCREEN OF THE PROGRAM, BY PRESSIN G SUCCESSIVELY ON : ALT N

FOR OFFLIN E/ MON ITOR/ ON LIN E MODE CHAN GE

ALSO SELECTS DIRECTION OF READIN G IN TABLE OF VARIABLES SAME AS A ALT N

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 20 / 23

P320 EL
P8 PROGRAMMING SOFTWARE
AFTER SELECTIN G "PROGRAM FOLDERS" USIN G F8 F1
F1

TO

F10 SAME AS FOR FIRST SCREEN

SELECT

SUPPRM

AUTO

SAUVEG

RESTIT

REN OMM

EFFACE

VERROU

COPY

CREATION A N EW PROGRAM FOLDER OR SELECTION FROM LIST OF THOSE ALREADY CREATED

DELETES A FOLDER FROM THE LIST BUT CAN N OT DELETE THE FOLDER BEIN G WORKED ON , CALLED THE : "CURREN T FOLDER "

AUTOSELECTION FROM LIST OF FOLDER SAM E AS THE ON E LOADED IN TO THE CON TROLLER (AFTER SELECTIN G WITH F1)

SAVES THE CURREN T FOLDER ON THE HARD DISK OR ON THE DISKETTE WITH THE APPROPRIATE PATH A:\ FOLDER N AM E

RESTORAL IN THE CURREN T FOLDER FROM THE BACKUP OF THE HARD DISK OR DISKETTE A:\ FOLDER N AM E

USED TO CHAN GE THE N AM E OF THE CURREN T FOLDER

ERASES THE CON TEN TS OF THE CURREN T PROGRAM FILE WITHOUT ERASIN G THE N AM E

LOCKS OR UN LOCKS THE CURREN T PROGRAM FOLDER TO PREVEN T CERTAIN PRECEDIN G OPERATION S

COPIES THE CON TEN TS OF AN Y FILES IN TO THE CURREN T FILE M AY BE DON E FROM A DISKETTE

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 21 / 23

P320 EL
P8 PROGRAMMING SOFTWARE

AFTER SELECTIN G "UTI LI TI ES : TRAN SFERS, ERASE" USIN G F9 F1

TO

F10 SAM E AS FO R FIRST SCREEN

CO N

PLC

CH ECK

ERASE

PRO M

TRAN SFERTS A CO M PLETE O R IN CO M PLETE FO LDER FRO M PLC TO TH E CO N SO LE IN "RU N " O R "STO P" M O DE

TRAN SFERTS A CO M PLETE O R IN CO M PLETE FO LDER FRO M CO N SO LE TO TH E PLC IN "O N LIN E" M O DE

CO M PARISO N O F CO N TEN TS O F FO LDER O N H ARD DISKETTE AN D TH E O N E EXISTIN G IN TH E PLC

ERASES FRO M TH E PLC M EM O RY, AS CH O SEN : - TH E PRO GRAM - TH E CO N FIGU RATIO N - TH E REFEREN CE TABLES - TH E FO RCIN G TABLES

USED TO READ, WRITE O R CH ECK BETWEEN TH E EEPRO M AN D RAM M EM O RIES O F TH E PLC PLC IN STO P M O DE

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 22 / 23

P320 EL
P8 PROGRAMMING SOFTWARE
AFTER SELECTING "PRINTING FUNCTIONS" USING F10 F1
F1

TO

F10 SAME AS FOR FIRST SCREEN

PARAM

SCREEN

PROGRM

XREF

VALUE

PAUSE

SAVE

SETTING OF PRINTER PARAMETERS - PAGE WIDTH - NUMBER OF LINES PER PAGE - ETC

DESTINATION OF PRINTING SCREEN PORT OR FILE

CONFIGURATION OF FOLDER FOR PRINTING TO A PRINTER OR A FILE

WHEN PRINTING IS STARTED, MAKES IT POSSIBLE TO INSERT THE CROSS REFERENCES ACCORDING TO THE CHOICE OF SORTING IN THIS SCREEN

ALLOWS THE PRINTING OF VALUES OF VARIABLES SPECIFIED IN TABLE FORM TO THE PRINTER OR TO A FILE

ALLOWS A TEMPORARY STOP DURING PRINTING

SAVES PRINTING PARAMETERS CONFIGURED PREVIOUSLY IN A FILE : PRINT.SET

September 2009

PDT-CS-10/P320 EL 4 C

Chapter 04

page 23 / 23