Inverter Microprocessor-controlled

CERTIFIED KUBOTA MFG. CORP.

sNewly employs a tool-less rotor that is easy to set up.

sConforms to the international safety standard IEC 61010-2-020. Forward-looking concerning safety. (Products after August 2000 conform.) sEmploys a new special damper that has a large damping effect. The drive section requires minimum maintenance.
Centrifuging is possible with the samples balanced by eye measure.
The tool-less rotors can be set or changed without using a tool. (except angle rotors) For routine work. Easy-to-use and convenient functions.
Memory flushing function for easy spin-down (patent pending) Automatically memorizes the duration of spin-down operation ranging from 1 to 90 seconds. Merely pressing the key the next time starts the spin-down for the memorized duration. 5 operation condition memory settings are available, and one-touch saving, access and operation are possible. Acceleration and deceleration curve can be varied in three steps according to the sample and purpose. Density-gradient centrifuging is possible. Integrator function that can attain optimization of centrifuging conditions. g-sec value (integrated RCF value) can be measured, and operation with this value set is possible. The timer can be set up to 990 minutes or seconds. During hold operation, the elapsed time of operation is displayed. Lid lock release by a foot switch (optional), eliminating the need for touching the panel.

Designed with safety in mind and in conformance with the international safety standard IEC 61010-2-020. Conformance to this standard will become increasingly important in the future.
It is designed so that no fragments will be ejected from the centrifuge even if the rotor is broken. The lid lock is interlocked, and a twin lock system of 2 right and left hooks is employed. The interlock is protected against shocks and employs an electrical double protection circuit.

Complete with various sensors for higher safety. Stops when an abnormality is detected.
Comes with automatic rotor identification function (patented). Rotor type is automatically identified and overspeed detection is enabled when a rotor is simply placed on the drive shaft. Comes with imbalance detection, abnormally high temperature detection, abnormality detection of spin sensor and temperature sensor, and a circuit breaker.
Speed

Step centrifugation mode

Step centrifuging function

Comes with a GMP requirements tachometer port.

Makes it easy to check the actual rotor speed.

Time

A variety of rotors and accessories are available for multipurpose applications.

The swinging bucket rotor ST-410 (optional) accommodates anti-biohazard sealing caps.

Acceleration and deceleration characteristics

Very slow acceleration and deceleration are suitable for centrifuging of samples that are sensitive to stirring. Suitable for the density gradient method and for blood washing or other centrifuging operations of samples that are apt to stir. For very slow acceleration and deceleration, a characteristic changeover speed N can be set.
Speed N Speed of characteristic switching rotation

Sample temperature is kept at 4C at the maximum speed of any rotor (at ambient temperature of 25C). Designed considering friendliness to the global environment and recycling.
Employs CFC-free HFC134a for the refrigerant. On the main unit, only a small amount of plastic is used to reduce the load on the environment.

Super slow Rapid Slow Rapid

Time Slow Super slow

Integrator function g . sec value

Standard mode

A thermostatic refrigerated centrifuge (-20 to 60C) is available (optional). A safety cabinet with an anti-biohazard HEPA filter (Class I) can be set (optional).

The integrator function can reproduce the same centrifugal effect. =

Time

Autoclaving (121C) possible

RCF

Autoclaving (121C) possible

ST-720 Swinging bucket rotor

ST-410 Swinging bucket rotor

Photographed with sealing caps put on.

Sealing cap
Code No. S17111 (optional)

ST-480 Swinging bucket rotor

PT-20/21 Plate rotor

6 x microtiter plates
With the PT-21, ethanol precipitation is possible at 3,100 xg.

Rotor, Bucket, Tube Rack Table for model 5910

Rotor Name Nominal Capacity Tube sizes (mm) diam. x length Maximum Speed rpm Maximum RCF xg Bucket Code No. Tube Rack Adaptor Code No.

Swinging Bucket Rotors

80 x 2mL 96 x RIA tube 48 x 5/7mL narrow blood collecting tube 8 24 x 8mL CPT cell preparation tube 9 80 x 10mL 48 x 10mL Vacutainer tube/15mL 68 x 5/7mL narrow blood collecting tube 8 68 x 10mL Vacutainer tube/15mL 28 x 15mL Conical tube 32 x 15mL Conical tube 8 x 50mL 16 x 50mL Conical tube 4 x 100mL 1 4 x 175mL Conical tube 1 4 x 200mL Conical tube 1 4 x 225mL Conical tube 4 x 250mL 48 x 2mL 48 x 5mL 48 x 7mL 28 x 7mL Vacutainer tube 2 12 x 15mL Conical tube 2 12 x 15mL Conical tube 28 x 10mL Vacutainer tube/15mL 4 x 50mL 4 x 50mL 4 x 50mL Conical tube 4 x 100mL 4 x 200mL 64 x 2mL 48 x 10mL 32 x 10mL Vacutainer tube/15mL 3 4 4 x 50mL 4 8 x 50mL 16 x 15mL Conical tube 5 4 x 50mL Conical tube 5 8 x 50mL Conical tube 6 x Micro plates 2 x Deep well plate 6 x Micro plates 2 x Deep well plate 8 x Micro plates 4 x Deep well plate 12 x Micro plates 4 x Deep well plate 24 x 12mL 8 x 15mL Conical tube 8 x 50mL Conical tube 10 x 50mL 24 x 15mL 9.5~11 x 36~42 10~12.3 x 65~95 12~13.3 x 63~110 13.5~15.8 x 81~130 12.5~13.8 x 65~95 15~17.2 x 81~110 12.5~13.7 x 62~110 15~17.2 x 52~110 17 x 121 17 x 121 27~36.4 x 85~110 30 x 117 38~46.5 x 75~120 61 x 118 61 x 130 61 x 137 60~61.8 x 100~130 10.7 x 42 12.5 x 55~75 12~12.5 x 100~112 12.5~13 x 75~106 16.5 x 120.6 16.5 x 120.6 15.5~17 x 87~110 34 x 110 27~35.8 x 82~110 29.5 x 117 44~45 x 110 56.5 x 104 9.5~11 x 36~42 12~13.3 x 46~110 15~17.2 x 86~110 27~38 x 100~110 27~38 x 100~110 17 x 121 30 x 117 30 x 117 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 3,000 3,000 3,500 5,000 3,500 5,000 5,000 3,500 2,290 2,190 2,310 2,310 2,260 2,330 2,300 2,300 2,300 2,330 2,330 2,330 2,330 2,330 2,330 2,330 2,380 4,160 4,160 4,160 4,160 4,160 4,470 4,160 4,160 4,160 4,160 4,160 4,160 1,570 1,600 2,270 4,640 2,270 4,640 4,640 2,270 053-5820 053-5820 053-5820 053-5820 053-5820 053-5820 053-5840 053-5840 053-5840 053-5820 053-5820 053-5820 053-5820 053-5820 053-5820 053-5820 053-5820 attached to rotor attached to rotor attached to rotor attached to rotor attached to rotor S13130 attached to rotor attached to rotor attached to rotor attached to rotor attached to rotor attached to rotor 053-7030 053-7190 053-7130 053-7110 053-7150 053-5790 053-5010 053-5020 055-4800 055-4730 055-4990 055-6900 055-4740 055-4750 055-0260 055-4780 055-4760 055-6070 055-4770 055-4850 055-4850 055-4850 055-4850 S17008 S17006 S17007 S17027 S17019 S17015 S17050 055-5670 S17049 S17100 055-1270

ST-720
7

ST-410
7

ST-480
7

Swinging Bucket Rotors for micro plates

PT-20 PT-21 PT-89 PT-745S
6 6 6 6 6 6 6 6 7

86 (W) x 128 (D) x 52 (H) 86 (W) x 130 (D) x 62 (H) 86 (W) x 130 (D) x 89 (H) 86 (W) x 128 (D) x 90 (H)

4,000 5,000 2,400 4,200

1,790 3,100 1,080 3,100

attached to rotor attached to rotor attached to rotor attached to rotor

055-6370 055-6380

Angle Rotors
RA-288M3 RA-410M3 RA-500M3 AT-360 15.9~16.5 x 97~120 17 x 121 30 x 117 26.4~29.2 x 98~121 15~17.2 x 96~130 8,500 8,500 8,500 8,500 3,500 9,690 9,530 9,690 9,690 2,270 055-1280

1 Conical tubes 175 mL, 200 mL, and 225 mL can be centrifuged by using supporters. The 175 mL conical tube is made by Falcon (code No. 2076) and needs a cushion (code No. 2090). The 200 mL conical tube is made by Nalge Nunc (code No. 376813) and needs a cushion adapter (code No. 377585). The 225 mL conical tube is made by Falcon (code No. 2075) and needs a cushion (code No. 2090). 2 sealing cap cannot be used on this tube rack. sealing cap (code no. S17111) can be used on a 12 x 15 mL conical tubes with code No. S13130. 3 sealing adapter against biohazard for 50 mL conical tube (code no. 055-5760) and for 15 mL conical tube (code no. 055-5750) can be used. 4 15 mL glass tubes can be used if an adapter (code no. 055-7400) is added and need a rubber cushion (code no. 024-1400) sold separately. 5 15 mL conical tubes can be used if an adapter (code no. 055-1280) is added. 6 If micro plates are used, it is possible to stack them in double or more on each bucket. However, be sure to test the strength of those plates prior to centrifugation. The micro plate at the bottom may be crushed. 7 Contact your dealer in case you use two or more swinging bucket rotors and/or swinging bucket rotors for micro plates. 8 5/7mL narrow tube made by Sekisui (InsepackII), Termo (VenojectII), Nipro (Neotube) and Becton Dickinson (Vacutenar) can be used. Tube for flow cytometry can be used. 9 The CPT cell preparation tube is made by Becton Dickinson (Vacutenar 8mL for CPT cell separation).

PT-89 Plate rotor

Can centrifuge 8 microtiter plates or a filter plate + 2 deep-well plates. Can centrifuge a plate up to 89 mm in height.

PT-745S Plate rotor

Can centrifuge 12 microtiter plates or a plate up to 90 mm in height. Ethanol precipitation is possible at 3,100 xg.

RA-288M3 Fixed-angle rotor

24 x 12mL

RA-410M3 Fixed-angle rotor

Can centrifuge 50mL and 8 x 15mL Conical tube.

RA-500M3 Fixed-angle rotor

10 x 50mL

Specifications
Model 5910
Maximum Speed Maximum RCF Maximum Capacity Control system Speed setting Speed indication RCF setting RCF indication Integrator setting and indication 8500 rpm 9690 xg 1020 mL Micro-processor control (Brushless motor) Speed, RCF, Time, Acceleration & Deceleration, 5 channel memories From 200 to 8500 rpm, 10 rpm increments Digital display, From 0 to 8900 rpm, 10 rpm increments From 10 to 9690 xg, 10 xg increments Digital display, From 0 to 10620 xg, 10 xg increments Digital display, From 1.00 to 9.99 x 10 9 g sec from 1 sec. to 100 sec., in 1 sec. increment setting from 100 sec. to 990 sec., in 10 sec increments setting from 1 min. to 100 min., in 1 min. increment setting from 100 min. to 990 min., in 10 min. increments setting Digital display, 1C increments setting and indication from 20C to 40C Single phase AC115V10%, 50/60Hz, 15A Single phase AC220V10%, 230V10%, 50/60Hz, 10A 115V, 12A 220/230V, 7.5A 115V, 910W 3.3MJ/h 220/230V, 1.2kW 4.3MJ/h 50(W) x 65(D) x 85(H) cm1, 110kg Manufactured and tested in accordance with IEC 61010-2-020

Temperature setting and indication Power requirements Rated voltage and Rated current Power consumption and Heat output Dimensions, weight Test standard

(1) Those of projections are not included. All specifications and external appearance subject to change without notice. * On Model 5910 only use KUBOTA made rotor, adapter and tube rack. Do not attempt use rotors, adapters or tube racks made by other manufacturers. * The rotor mentioned in the catalogue is usable on other KUBOTA centrifuge models. For details, refer to the catalogues relevant to each model. * Follow instructions given in the relevant Instruction & Service Manual for operating centrifuges.

Anti-biohazard sealing adapters

For use with the buckets (Code No. 053-7110) on a swinging bucket rotor.
High maximum speed and high maximum RCF while inexpensive. Code No. 055-5750
For use with 15ml Conical (TC) 5,000 rpm 4,580 xg

Swinging bucket rotor ST-480

Code No. 055-5760

For use with 50ml Conical (TC) 5,000 rpm 4,560 xg

Code No. 055-4310

For use with 50ml oak ridge tube 5,000 rpm 4,440 xg

Safety Precautions

For your safe use of this equipment, be sure to read the instruction manual carefully before you start its operation.

Parts may be adversely affected by heat, humidity and specimens or deteriorated by aging resulting in functional failures or may even lose their safety characteristic to cause accidents. To prevent occurrences of functional failures or accidents, turn off the power switch, pull out the power cable plug from the plug socket and be sure to contact your nearest Kubota Dealer, or an office of Kubota Corporation when there is no Kubota Dealer in your neighbourhood.

The rotor or bucket has been found to be damaged or corroded. Always discontinue A burnt smell comes out of the equipment. use when You receive a minor electrification when you touch the IMPORTANT phenomena listed equipment body by a naked hand. DISCONTINUE at right appear. Some other abnormality or failure has been found occurring. USE

http://www.centrifuge.jp
29-9 Hongo 3-chome, Bunkyo-ku, Tokyo 113-0033, Japan Telephone: (03) 3815-1331 Facsimile: (03) 3814-2574 E-mail: [email protected]
Note: This catalogue is not for distribution in the USA, Canada and Mexico as products shown are not for sale in these countries.
Copyright 2006 KUBOTA CORPORATION G1, Printed in Japan