Scribd
Upload
164 views3 pages

Crystal Oscillator Specification: OCXO 143-1002

This document provides specifications for an ovenized crystal oscillator. It summarizes the operating characteristics including an output frequency of 13 MHz with long term stability assured by premium components. Key specifications outlined include frequency stability under various conditions, electrical frequency adjustment range, input power requirements, and environmental tolerances. Dimensional drawings and pin connections are also included.

Uploaded by

snewton6752
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
164 views3 pages

Crystal Oscillator Specification: OCXO 143-1002

This document provides specifications for an ovenized crystal oscillator. It summarizes the operating characteristics including an output frequency of 13 MHz with long term stability assured by premium components. Key specifications outlined include frequency stability under various conditions, electrical frequency adjustment range, input power requirements, and environmental tolerances. Dimensional drawings and pin connections are also included.

Uploaded by

snewton6752
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

OCXO 143-1002

www.isotemp.com www.taitien.com

CRYSTAL OSCILLATOR SPECIFICATION


This specification defines the operating characteristics of an ovenized crystal oscillator. Long term stability is assured through use of premium components.

REV. -

DESCRIPTION OF REVISION

DWN. BY

APV. BY

DATE 08-24-2011

JTL

TST

1. OUTPUT(PIN = "R.F. OUTPUT") 1.1. Frequency 1.2. Initial Accuracy a. @ Temperature b. After time on power c. Within time period following date code d. @ VCO Input voltage 1.3. Waveform 1.4. Level a. "1" level b. "0" level 1.5. Load 1.6. Duty cycle 1.7. Spurious 2. FREQUENCY STABILITY 2.1. Ambient 2.2. Aging a. At time of shipment b. After indefinite storage i. Daily ii. Yearly iii.10 years 2.3. Voltage 2.4. Short term 2.5. Load 2.6. Warm-up 2.7. Phase Noise a. @ 1 Hz b. @ 10 Hz c. @ 100 Hz d. @ 1 kHz e. @ 10 kHz

13.000000 MHz < 2x10-7 +25 1C 30 5 minutes 90 days +2 0.001 V Rectangular HCMOS > Vcc - 0.6 V < +0.4 V 15 pF 45% to 55%@ +2.5 V < -60 dBc

< 1x10-8, 0C to +70C (referenced to +25C) < 1x10-9/day < 1x10-9 after 30 days < 1x10-7 < 4x10-7 < 1.5x10-8/5% change < 5x10-11/second root Allan variance < 5x10-9/5% change < 2x10-8 in 5 minutes @ +25C (referenced to 1 hour) < < < < < -80 dBc -120 dBc -140 dBc -145 dBc -150 dBc

OUR PERFORMANCE YOUR REPUTATION

MODEL NO. OCXO 143-1002

PAGE OF TOTAL
1 2

DWG. NO. 114-1480

REV. -

OCXO 143-1002
www.isotemp.com www.taitien.com

3. ELECTRICAL FREQUENCY ADJUSTMENT (PIN = "VCO INPUT") 3.1. Range > 8x10-7 < 2x10-6 Referenced to frequency at nominal Center Voltage 3.2. Control 0 to +4 V 3.3. Slope Positive 3.4. Center Voltage +2 V NOTE: When not connected, VCO INPUT is internally held at this voltage. 3.5. Linearity < 10% 3.6. Input impedance > 100 k 4. INPUT 4.1. 4.2. 4.3. POWER (PIN = "+VDC") Voltage Current Steady state

+5 V 5% < 850 mA @ turn on < 1.5 Watts @ +25C

5. ENVIRONMENTAL 5.1. Storage temperature 5.2. Vibration (non-operating) 5.3. Shock (non-operating)

-40C to +85C MIL-STD-202, Method 201 (0.06" Total p-p, 10 to 55 Hz) MIL-STD-202, Method 213, Test Condition J (30 g, 11 ms half-sine)

6. RoHS All units supplied under this MODEL NUMBER are RoHS compliant. 7. MECHANICAL(Outline drawing) 7.1. Applicable series 7.2. Model number 7.3. Outline drawing

OCXO 143 series OCXO 143-1002 125-608

OUR PERFORMANCE YOUR REPUTATION

MODEL NO. OCXO 143-1002

PAGE OF TOTAL
2 2

DWG. NO. 114-1480

REV. -

PIN CONNECTIONS
PIN
MOD: FREQ.: S/N: DATE:

FUNCTION
R. F. OUTPUT 0 VOLTS & CASE VCO INPUT
or

1 2
MARKING THIS SURFACE

3
(See Note 1)

NOT CONNECTED

(VIEW FROM TOP)

(See Note 1)

4 5

REFERENCE VOLTAGE
or

NOT CONNECTED +VDC

0.026 0.66

0.539 MAX. 13.69

0.20 MIN. 5.08

Note 1. If the specification does not specify parameters for either PIN3 or PIN4 then that respective PIN is NOT internally CONNECTED.

GLASS STANDOFF (4 PLACES) 0.750 CENT. 19.05

0.031 DIA. PIN (5 PLACES) 0.80

MARKING

MOD: FREQ.: S/N: DATE:

4 0.750 CENT. 19.05 1.015 SQ. MAX. 25.78


MOD: FREQ.: S/N: DATE:

2 C L

(VIEW FROM BOTTOM)

NUMBERS FOR REFERENCE ONLY (NOT STAMPED ON UNIT)


OSCILLATORS

INCH mm (REFERENCE ONLY)

Form NO. 120-081E

REV: B SHT: 1 OF 1

DWG: 125-608

Charlottesville, Virgina USA CODE I.D. NO. SCALE: 2:1 DWN. BY: LRB
10-27-2003 02-13-2009

NAME: OUTLINE DRAWING


(OCXO 143 SERIES)
A B 0.539 / 13.69 MAX. W AS 0.55 / 13.97 MAX. UPDATED MARKING .

DATE: 09-09-2002 APPR'D. BY: TST TOLERANCES

31785
DAG BTG BTG TST

UNLESS OTHERWISE SPECIFIED: ANGES: 1 DEGREE FRACTIONS: 1/32 INCH DECIMALS: .XX .015, .XXX .010 INCH

MATERIAL: STEEL LET REVISION BY APP DATE FINISH: NICKEL MARK: LABEL

You might also like