Scribd
Upload
145 views3 pages

131 1009

This document provides specifications for an ovenized crystal oscillator. It lists the operating characteristics including an output frequency of 13 MHz with less than 1x10-7 accuracy initially and over time. Long term stability is ensured by premium components. The oscillator has excellent frequency stability even over wide temperature ranges and aging. It is RoHS compliant and can withstand harsh storage and operating environments.

Uploaded by

snewton6752
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
145 views3 pages

131 1009

This document provides specifications for an ovenized crystal oscillator. It lists the operating characteristics including an output frequency of 13 MHz with less than 1x10-7 accuracy initially and over time. Long term stability is ensured by premium components. The oscillator has excellent frequency stability even over wide temperature ranges and aging. It is RoHS compliant and can withstand harsh storage and operating environments.

Uploaded by

snewton6752
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

OCXO 131-1009

www.isotemp.com www.taitien.com

CRYSTAL OSCILLATOR SPECIFICATION


This specification defines the operating characteristics of an ovenized crystal oscillator. Long term stability is assured through use of premium components.

REV. -

DESCRIPTION OF REVISION

DWN. BY

APV. BY

DATE 08-12-2011

JTL

TST

1. OUTPUT(PIN = "R.F. OUTPUT") 1.1. Frequency 1.2. Initial Accuracy a. @ Temperature b. After time on power c. Within time period following date code d. @ VCO Input voltage 1.3. Waveform 1.4. Level 1.5. Load 1.6. Harmonics 1.7. Spurious 2. FREQUENCY STABILITY 2.1. Ambient 2.2. Aging a. At time of shipment b. After indefinite storage i. Daily ii. Yearly iii. 10 years 2.3. Voltage 2.4. Short term 2.5. Load 2.6. Warm-up 2.7. Phase Noise a. @ 1 Hz b. @ 10 Hz c. @ 100 Hz d. @ 1 kHz e. @ 10 kHz

13.000000 MHz < 1x10-7 +25 1C 30 5 minutes 90 days +3.0 0.001 V Sine wave +9 2 dBm 50 < -30 dBc < -80 dBc

< 2.5x10-8, -30C to +70C (referenced to +25C) < 1x10-9/day < 1x10-9 after 30 days < 1x10-7 < 4x10-7 < 2x10-9/5% change < 2x10-11/second root Allan variance < 1x10-9/5% change < 2x10-8 in 5 minutes @ +25C (referenced to 1 hour) < < < < < -80 dBc -115 dBc -135 dBc -147 dBc -150 dBc

OUR PERFORMANCE YOUR REPUTATION

MODEL NO. OCXO 131-1009

PAGE OF TOTAL
1 2

DWG. NO. 114-1473

REV. -

OCXO 131-1009
www.isotemp.com www.taitien.com

3. ELECTRICAL FREQUENCY ADJUSTMENT (PIN = "VCO INPUT") 3.1. Range > 6x10-7 < 1.2x10-6 Referenced to frequency at nominal Center Voltage 3.2. Control 0 V to +6 V 3.3. Slope Negative 3.4. Center Voltage +3.0 V 3.5. Linearity < 15% 3.6. Input impedance > 100 k 4. INPUT 4.1. 4.2. 4.3. POWER (PIN = "+VDC") Voltage Current Steady state

+12 V 5% < 250 mA @ turn on @ +25C < 1.2 Watts @ +25C

5. REFERENCE VOLTAGE (PIN = "REFERENCE VOLTAGE"), an output 5.1. Voltage +7.5 V 5% 5.2. Load > 9 k 5.3. Source Impedance < 100 6. ENVIRONMENTAL 6.1. Storage temperature 6.2. Vibration (non-operating) 6.3. Shock (non-operating)

-40C to +85C MIL-STD-202, Method 201 (0.06" Total p-p, 10 to 55 Hz) MIL-STD-202, Method 213, Test Condition J (30 g, 11 ms half-sine)

7. RoHS All units supplied under this MODEL NUMBER are RoHS compliant. 8. MECHANICAL(Outline drawing) 8.1. Applicable series 8.2. Model number 8.3. Outline drawing

OCXO 131 series OCXO 131-1009 125-587

ISOTEMP is your oscillator source.

OUR PERFORMANCE YOUR REPUTATION

MODEL NO. OCXO 131-1009

PAGE OF TOTAL
2 2

DWG. NO. 114-1473

REV. -

PIN CONNECTIONS
PIN
MOD: FREQ.: S/N: DATE:

FUNCTION
VCO INPUT
or

(See Note 1)

(VIEW FROM TOP)

MARKING THIS SURFACE

2
(See Note 1)

NOT CONNECTED REFERENCE VOLTAGE


or or

OVEN MONITOR NOT CONNECTED +VDC R. F. OUTPUT 0 VOLTS & CASE

0.737 MAX. 18.72

3 4 5

0.026 0.20 MIN. 0.66 5.08 0.031 DIA. PIN (5 PLACES) 0.79 GLASS STANDOFF (4 PLACES)

Note 1. If the specification does not specify parameters for either PIN1 or PIN2 then that respective PIN is NOT internally CONNECTED.

MARKING

1.43 MAX. 36.32 1.000 CENT. 25.40

MOD: FREQ.: S/N: DATE:

4 1.07 0.700 CENT. 27.18 17.78 5


MOD: FREQ.: S/N: DATE:

C L

(VIEW FROM BOTTOM)

NUMBERS FOR REFERENCE ONLY (NOT STAMPED ON UNIT)

INCH mm (REFERENCE ONLY)


OSCILLATORS

Form NO. 120-081E

REV: C SHT: 1 OF 1

DWG: 125-587

Charlottesville, Virgina USA CODE I.D. NO. SCALE: 1:1 DWN. BY: LRB
12-06-2001 02-01-2008 04-16-2010

NAME: OUTLINE DRAWING


(TCXO 141 & OCXO 131 SERIES)
A B C 1.07 WAS 1.07 MAX NEW FORM AND UPDATED MARKING. HEIGHT WAS .750 AND UPDATED MARKING.

DATE: 12-04-2000 APPR'D. BY: DAG TOLERANCES

31785
DAG BTG BTG TST JRD TST

UNLESS OTHERWISE SPECIFIED: ANGES: 1 DEGREE FRACTIONS: 1/32 INCH DECIMALS: .XX .015, .XXX .010 INCH

MATERIAL: STEEL LET REVISION BY APP DATE FINISH: NICKEL MARK: LABEL

You might also like