Tutorial Citec

Quickstart Tutorial V7.
10
In approximately one hour, completing this tutorial will give you a basic working knowledge of CitectHMI/SCADA version 7.10 software. Learn how to build a small project, configure dynamic graphics, create alarms and trends, and then run your project like a real plant. This tutorial will also show you some shortcuts that, over time, will save you far more than the one hour you may take to complete the exercises inside.
1 Page 1 of 80
Quickstart Tutorial V7.10

Quickstart Tutorial ..................................................................................................................................................................3 Definition of Terms .................................................................................................................................................................4 Create a New Project Folder ..................................................................................................................................................6 Configuring Clusters ...............................................................................................................................................................7 Configure an I/O Device .......................................................................................................................................................11 Configuring Tags ..................................................................................................................................................................14 Creating Graphic Pages .......................................................................................................................................................17 Creating Graphic Pages, Creating a new page ....................................................................................................................18 Creating Graphic Pages, Saving your page .........................................................................................................................19 Creating Graphics pages, Setting up the Grid ......................................................................................................................20 Creating Graphics pages, Configuring buttons.....................................................................................................................21 Creating Graphics Pages, Configuring Symbol Sets ............................................................................................................27 Creating Graphics Pages, Aligning Objects..........................................................................................................................30 Creating Graphics Pages, Formatting with Rectangles ........................................................................................................32 Testing Graphics Pages, Computer Setup Wizard ...............................................................................................................35 Testing Graphics Pages, Runtime ........................................................................................................................................38 Creating Graphics Pages, Analog Indicators & Controls ......................................................................................................40 Creating Graphics Pages, Configuring Text .........................................................................................................................44 Creating Graphics Pages, Creating Colors...........................................................................................................................44 Creating Graphics Pages, Configuring Numbers..................................................................................................................46 Creating Graphics Pages, 3D rectangles .............................................................................................................................46 Creating Graphics Pages, Pumps & Piping ..........................................................................................................................48 Creating Graphics Pages, Managing True Colors ................................................................................................................53 Accessing Alarm and Trend Display Pages..........................................................................................................................55 Configuring Alarms ...............................................................................................................................................................55 Configuring Trends ...............................................................................................................................................................56 Configuring Security .............................................................................................................................................................57 Using Find and Replace .......................................................................................................................................................59 Runtime ................................................................................................................................................................................61 Runtime, Trends ...................................................................................................................................................................64 Runtime, Process Analyst ....................................................................................................................................................66 Administrative Tools .............................................................................................................................................................70 Administrative Tools, Configuring the Menu .........................................................................................................................71 Administrative Tools, Tag Debug .........................................................................................................................................74 Backing Up Your Project ......................................................................................................................................................75 Restoring Your Project .........................................................................................................................................................76 Troubleshooting....................................................................................................................................................................78 Addendum Security Validation ..........................................................................................................................................79
2 Page 2 of 80

Quickstart Tutorial
Welcome, and thank you for purchasing CitectHMI or CitectSCADA. We would like your experience with the product to be a pleasant one, so we have created this tutorial to help new users get familiar with some of the fundamental features of the product. Disclaimer
Citect Pty Ltd makes no representations or warranties with respect to the contents
The tutorial is designed so that you can complete it in around one hour. The tutorial is not intended as a substitute for attending a CitectHMI/SCADA training course. We encourage you to attend a training course to complete your basic training, learn how to use time saving tools or go on to learn some of the more advanced features of the product.
or use of this manual and, to the extent permitted by law, expressly limits its liability for breach of any warranty that may be implied to the replacement of this manual
This tutorial assumes that you have already successfully installed the CitectSCADA product on your computer. You do not require a Citect license to complete this tutorial.
with another. Citect Pty Ltd assumes no responsibility for any errors that may be in this
Repetition is an important part of learning or memorizing. One way you can speed up your familiarization is to take a few minutes to click through all the menus in the of something, dont be concerned just move on to the next one anyway. You may not consciously remember everything product and (briefly) try and figure out what each item might be for, if you cant make sense you see, but it helps to set a framework for when you revisit these items in the tutorial and in this way you will remember them much better.
document and reserves the right to revise this document at any time without incurring an obligation to notify any person of the revision. Copyright October 2008,
By completing this tutorial you will learn the following Creating a New Project Setting Up Communications with a PLC Adding and Configuring tags Creating New Graphics pages Use Templates Button Commands Disabling Buttons Dynamic Symbols Drawing objects Manipulating objects Copy, Paste, Align, Send to Back, Color Fill, Control Commands, Setting values Drawing Text Displaying analog values Drawing Pipes Grouping Objects Defining Alarms Configure an alarm page Storing Trend Data Configuring a trend page Operating Runtime Displays Applying Security Using Administration Tools Creating Runtime Menus Tag Debug Utility Backing up and restoring a project
Citect Pty Ltd. All rights reserved. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Citect Pty Ltd.
Trademarks
Citect, CitectHMI, CitectSCADA, CitectSCADA Reports. CitectHistorian, AMPLA and Plant2Business are registered trademarks of Citect Pty Ltd. Windows is a trademark of Microsoft Corporation. All other brand or product names may be trademarks of their respective holders.
3 Page 3 of 80
Definition of Terms
Click = Briefly press left mouse button
Double Click
= Press left mouse button twice quickly
Right Click
= Briefly press right mouse button
Check
= A tick or cross in an options box
Type Text
= Type in the word Text
Drag
= Position mouse, click and hold left mouse button, move mouse, then release mouse button
Alt+Tab
= Press the Alt key, hold it down, then press the Tab key
Single Click
Right Click
Double Click
Click and drag
Type
4 Page 4 of 80

CitectHMI/SCADA is made up of a several configuration tools and a runtime section.
Citect Explorer Top level configuration interface
Citect Project Editor Mainly used for entering database type information
Citect Draw Used for creating graphics
Citect Runtime Provides the active operator interface
You can switch between these applications by:
1. 2.
Using the icons at the top left of each application, or Holding down the Alt key, then pressing Tab until the application you want is selected, then release the alt key (Alt+Tab), or
3.
Clicking on the icons that appear on the Windows task bar as shown below.
To make sure that you have selected the correct icon you can let the mouse hang over the icon for about 2 seconds and a tool tip will appear to guide you.
5 Page 5 of 80

Create a New Project Folder
Run the Citect Explorer.
As you go through this tutorial you might like to click
Click on Start Click All Programs Click Citect Click CitectSCADA 7.10 Click CitectSCADA Explorer
on the Help button located on many of the dialogs as this will show you some of the other options available to you that are not covered by this tutorial.
On the Tool Bar, click on the New Project icon
Project Folders store all of the CitectSCADA files for your project including graphic pages, tag definitions, code etc.
Clicking on a different project in Citect Explorer immediately changes the project you are working in.
You can combine multiple configuration projects into a single runtime project using the project include feature described in the online help.
Tip
Consider using the Quickstart Project as this can save you
In the New Project Dialog Box, type Tutorial in the Name field to give the new project a name, give it a description, then click OK.
a lot of time.
Use the Example project to get ideas and learn how things are made by pulling them apart.
6 Page 6 of 80

Configuring Clusters
Clusters define where server processes (IO communications, data logging, alarming, etc), are run, and how different server processes interact with each other for redundancy purposes (refer to the online help for more details). Every CitectSCADA system must have at least one cluster defined, with related Network Addresses and Server roles also defined.
CitectSCADA allows you to quickly and easily switch between different projects, simply by selecting them in the Project List. TIP Make sure all pages are
Expand your project tree on the left-hand side of Citect Explorer and select Communications. Then double-click on Clusters.
saved or closed in the Graphics Builder before changing projects.
When you backup a project, everything related to that project, including Cicode or VBA script, is backed up and easily transported to other computers. The only exception is any 3rd party items which need to be installed separately such as ActiveX objects. TIP When networking your system, the project does not need to be copied to every computer. Refer projects, Managing your projects, Linking projects
If the Project Editor does not appear, then use Alt+Tab until it appears.
7 Page 7 of 80

Configuring Clusters continued
In the Clusters form that appears, define a cluster called MyCluster; give it an appropriate description in the Comment field, then Click Add.
IMPORTANT Do NOT press ENTER before filling in all the required fields in a form. Each time you press ENTER a new record will be added to the project creating duplicates which will cause compilation failures.
Similarly, make sure you only single-click the Add button, rather than double-clicking, otherwise duplicate records will be added causing complication failures.
For learners, it is better to use the Add button instead of the ENTER key. If you add an extra record by mistake, you can use the Delete button to mark it for deletion.
Close the Clusters window by clicking on the
or pressing ESC.
Once marked for deletion the record will be ignored.
From the pull-down menu at the top of the Citect Project Editor, click on Servers, then Network Addresses.
If you press delete by mistake you can press it again to undelete. To view records marked for deletion go to Tools, select Options and check Show Deleted.
8 Page 8 of 80

Configuring Clusters continued...
TIP
Network Addresses define which computers are available on the network to operate as Citect Servers.
In the Network Addresses form, enter the Name MyAddress, the Address 127.0.0.1, and an appropriate Comment.
We can identify these computers by TCP/IP address, or computer name.
The universal loopback
When you are finished, click Add, then close the form. This assigns the loopback TCP/IP address to the system which is appropriate for Standalone systems only. We will then use that address for our server roles. We now need to assign both the Cluster and the Network Address to the various server roles that are required on this Citect system. This includes IO Communications, Alarming, Trending and Reporting roles. From the Servers menu select each of the server tasks in turn, and configure them as shown below:
address 127.0.0.1 is only appropriate for standalone systems with no clients.
For networked or redundant systems, refer to the online help for details on how to configure additional Network Addresses and use them in your Server definitions.
Use the pull-down lists where provided to minimise the chance of mistakes.
9 Page 9 of 80
Configuring Clusters continued...

This identifies the Alarm Server process to run on the computer with MyAddress TCP/IP address, within the MyCluster server group, in the Primary mode. The Server Name MyServer will be used by networked clients to connect to this server to acquire the alarm information for display purposes. Continue for Report, Trend and IO Servers as shown below:
The Tutorial project defines a single PC inside of a single cluster, and due to the loopback TCPIP address, is incapable of communicating to other CitectSCADA nodes or clients.
Refer to the online help for details on Primary and Standby server functions, and Clustering options for networked systems.
We have now completed our Server setup and are ready to define our communications path to the PLC.
10 Page 10 of 80
Configure an I/O Device

Use Alt+Tab to return to the Citect Explorer. Make sure the Tutorial project is selected in the project list on the left-hand side and that the Communications folder is open. Double click on Express I/O Device Setup.
On the Express Communications Wizard, just press the Next button for the first three steps, making sure your MyIOServer is selected as the existing I/O Server in the second step.
11 Page 11 of 80

Configuring I/O Device continued
Disk I/O Devices are serviced by the Citect I/O Server, which means all networked clients are looking at the same data. Disk data values are retained on shutdown as they reside on the I/O Servers hard drive.
Local Tags are serviced by each individual Citect node, so each client is looking only at its own data. Local Tag values are not retained when the Citect node is shutdown.
On the fourth step, click Disk I/O Device, then click Next. This configures the system to use a hard-drive based device instead of a real-world device. Disk I/O devices are useful for simulation and testing situations, as well as for persisting recipe or other information at the SCADA level instead of in the PLC.
On the fifth step, scroll to the top of the protocol list and select Citect Generic Protocol by clicking on it, then click Next.
12 Page 12 of 80

Configuring I/O Device continued
On the final two screens you just need to press the Next & Finish buttons.
Your system has now been configured to access a disk-based PLC to write and read data. Now we need to configure the tags in this PLC that the system will use to control equipment. In this tutorial we will be controlling a pump, its mode, and its speed.
13 Page 13 of 80

Configuring Tags
Variable Tags are a core building block for a CitectSCADA project. Tags provide the link between the operator and the real-world. We will create three tags to represent our pump, a Run/Stopped status tag, an Auto/Manual control tag and a Speed control tag. Making sure the Tutorial project is selected, click on the Tags folder. Then Double Click on Variable Tags in the right-hand pane.
IMPORTANT Do NOT press ENTER before filling in all the required fields. Each time you press ENTER a new record will be added to the project creating duplicates which will cause compilation failures. Similarly, make sure you only single-click the Add button, rather than double-clicking, otherwise duplicate records will be added causing complication failures. For learners, it is better to use the Add button instead of the ENTER key. If you add an extra record by mistake, you can use the Delete button to mark it for deletion. Once marked for deletion the record will be ignored. If you press delete by mistake you can press it again to undelete. To view records marked for deletion go to Tools, select Options and check Show Deleted. To permanently remove deleted records from the project, go to File then select Pack.
This will bring the Project Editor to the foreground and display the Variable Tags dialog. If it does not appear, use Alt+Tab to switch the view to the Project Editor.
The Project Editor is mainly for editing database type information. The Variable Tags Database has one record for each Tag you define. Each Tag has multiple fields. (Variable Tag name, Data Type, Address etc) You can see the record number indicated in the bottom left of the dialog box
14 Page 14 of 80

Configuring Tags continued
CAUTION
Where a drop down is provided you should use it. If you mistype data into fields that require specific settings you may cause compile errors.
You can save a lot of time configuring tags by entering similar types of Tags together and just changing the parts that are different before pressing Add. Use the mouse to highlight the parts that you want to change, then just overtype. Eg; Pump_1_CMD can easily be changed to Pump_1_Mode. Highlight CMD then type Mode. For address based protocols, if you arrange your variables in your PLC into blocks where all the Digitals are contiguous and all the Integers are contiguous then the performance will be significantly improved as the CitectSCADA software will be able to read large blocks of data in a single communication message instead of multiple messages. TIP It does not matter what order the addresses are entered into the variables records, what matters is the contiguous block of addresses in the PLC.
Next you will configure three tags as shown below. Remember to fill in the form before pressing Add or Enter. Use the Tab key or the mouse to move between fields. To make corrections after you have pressed add, you can move to the Tag or record by using the scroll bars on the right-hand side, then press Replace when you have made the changes. The cursors have been added as a guide to show you where you should type and where you should click.
If you are having difficulty reading from the screen grabs here is the information in plain format.
I/O Device Name Raw Zero Scale Eng Zero Scale Eng Units Comment
Pump_1_CMD IODev
Data Type Address
DIGITAL D1
Raw Full Scale Eng Full Scale Format Pump 1 Command On/Off
15 Page 15 of 80

Configuring Tags continued
CitectSCADA automatically saves your configuration to disk each time you add, replace or delete a record. Graphics behave differently where you must save your pages as you develop them.
Variable Tag Name I/O Device Name Raw Zero Scale Eng Zero Scale Eng Units Comment
Pump_1_Mode IODev
Data Type Address
DIGITAL D2
TIP Engineering Units which are not included with CitectSCADAs default pulldown list can be typed in manually. Any text can be entered as engineering units.
Raw Full Scale Eng Full Scale Format Pump 1 Mode 0 =Auto, 1 = Manual
Variable Tag Name I/O Device Name Raw Zero Scale Eng Zero Scale Eng Units Comment
Pump_1_Speed IODev
Data Type Address Raw Full Scale Eng Full Scale
INT I1
0 0
32767 500.0
RPM Format ###.#EU Pump 1 Speed (0 500 rpm)
NOTE: For the Format field, EU needs to be typed up after ###.# When you are finished, use the scroll bar on the right to scroll through each tag (record) and double check that you have entered the correct information. On the last tag, check that the number of tags (records) = 3.
16 Page 16 of 80

Close the Variable Tags window by clicking on the or pressing ESC.
Creating Graphic Pages

Before you start lets take a look at what you will create.
This page contains a number of buttons that allow the operator to control the pumps mode and operation, as well as a slider to control its speed. The pump itself will animate red or green depending on whether it is running or not, and the lights, bar graph and number will indicate its mode, operation and speed.
17 Page 17 of 80

Creating Graphic Pages, Creating a new page
Switch to the Graphics Builder click on the Graphics Builder icon .
The fastest way to drive any application is with the keyboard. Most programs have shortcut keys you may be surprised how quickly you can learn them.
Click on the New Page icon. A popup form will appear allowing you to select what type of new graphics object you would like to create.
Templates provide a vast range of pre-built functionality, making the task of building a new project with CitectSCADA extremely fast. All pages must be based on a template, even if it is a blank template. If you want to customize the look and feel of your pages, you can create your own templates from scratch, or copy the existing ones and modify them.
Click on the Page button. An additional popup form will appear allowing you to select a base template from which to create your new page.
NOTE Never modify templates, symbols or other items in the Example, Include or CSV_Include projects! These projects will be automatically re-loaded when you upgrade to the next version and your changes will be lost. Always copy items to your local project before modifying
Instead of double clicking on Normal we could single click on Normal and then click OK but that takes more time.
them.
Make sure XP_Style is selected in the Style box, then Double Click the Normal template as shown.
18 Page 18 of 80

Creating Graphic Pages, Saving your page
We are using the built-in templates to get a jump-start on your page. There are navigation buttons already configured for you and using templates helps to ensure a consistent look and feel throughout your project. This is very important if you want to make it easy-to-use for your operators.
You can move the Toolbox by placing the cursor on the title bar, hold down the left mouse key while moving the mouse.
Templates are displayed pretty much as they appear at runtime. ###.## indicates dynamic values that will change at runtime. +1, +2 etc are Animation Numbers that are used as references for graphics objects that will be displayed at these locations in runtime. Animation Numbers are not displayed at runtime. (x) is a script that is executed with the page.
If your toolbox does not appear, it can be toggled by pressing the F3 button, or selecting it from the View menu.
It is good practice to save your graphics pages regularly, so lets begin the habit right now.
Click on the Save icon on the menu bar
Type MyPage in the Page edit box, then press OK.
19 Page 19 of 80

Creating Graphics pages, setting up the Grid
Firstly we will setup a grid which will allow our cursor to snap to uniformly positioned locations on the screen, making it easier to size and position objects in relation to each other. On the toolbar, click View, then Grid Setup.
The Grid is not a necessary item for configuring graphics pages, however it vastly increases the ability to create uniform sized and positioned objects, which in turn makes your pages easier to visualize. If the Grid prevents you from positioning an object exactly where you want it, it can be toggled on and off using the F8 key.
In the Grid Setup form, change the size of the grid from 8 x 8 pixels, to 5 x 5 pixels as shown below. Select Snap to Grid, and then click OK to close the form.
Now we are ready to create and position our graphics objects.
20 Page 20 of 80

Creating Graphics pages, Configuring buttons
Next we will configure some buttons to control the mode of the pump. On the Toolbox click on the button icon.
The Toolbox options are, from left-to-right and top-tobottom: Free-form line Straight line Square/Rectangle Circle/Oval Polygon Pipe Text Number Button Animated symbol Trend Function Static symbol Genie ActiveX Process Analyst Database Exchange
To draw the button, click and hold the left mouse button while moving the mouse then release the left mouse button (ie. click and drag the mouse).
The position and size of the currently selected object are shown at the bottom right of the graphics builder
status bar.
21 Page 21 of 80
Creating Graphics Pages, Configuring Buttons continued
Once you release the mouse button, the Button Properties dialog popup will appear. Double Click on the word button in the Text edit box. This is a quick way to select a complete word. Next type Manual.
If you dont see the expected property sheet as you go through these exercises, then you may need to locate the correct sheet by looking at the screens on the page then click on the horizontal & vertical tabs to find the right sheet. Horizontal Tabs
Vertical Tabs
Click on the Input tab at the top of the form to configure the action the button will perform. Click on the Insert button. Click on Insert Tag option.
TIP Tabs with ticks on them indicate that configuration exists on that tab
In the Insert Tag Dialog Double Click on Pump_1_Mode.
22 Page 22 of 80

There are many ways to copy objects. Ctrl + D will duplicate the currently selected object. Ctrl + C will copy an object to clipboard. Ctrl + V will paste an object from clipboard. These last two work in almost all windows programs so are well worth remembering. You can also select Copy, Paste or Duplicate from the Edit menu or by using the icons on the menu bar. Copying objects also ensures that their dimensions are identical to each other, creating a more visually appealing user interface.
Pump_1_Mode will be inserted into the Up Command edit box. Click your mouse to the right of the Tag Pump_1_Mode and type = 1.
When the project is running, pressing on the Manual Button will set the tag Pump_1_Mode to a value of 1 to represent Manual mode. Repeated pressing of the button will continue to set the same value of 1 into the tag. Therefore we need a second button to set the tag to a value of 0 or Auto mode. We will achieve this by copying the first button and modifying the copy. We do this because it is often quicker to make copies of objects than to draw them from scratch. This also guarantees consistency of object sizes. Here is a quick way to make a copy and position an object. Place the cursor over the Manual Button. Hold down the Ctrl key. Hold down the left mouse button. Move the mouse to position the copy. Release the left mouse button. You dont need to be precise with position at this time we will fix that later using an alignment tool.
If you move the mouse immediately after holding down left mouse button, then you will only see the outline of the object as it is moved. If you wait half a second before moving the mouse, you will see the object itself being moved, making it easier to position it in its new location. The + sign will appear on the hand after pressing the Ctrl Key indicating a copy operation rather than a move operation.
23 Page 23 of 80

Double Click on the new button. In the Up Command edit box, replace the = 1 with a = 0. This will turn the digital tag Pump_1_Mode false to represent Auto mode.
Click on the Appearance Tab to change the text label on the button.
Double Click on the word Manual in the Text edit box, replace the text with Auto. Click OK when finished. We now have two buttons that will set the control mode of the pump to Auto or Manual. Next we need a control to turn the pump on and off. Instead of using two buttons, one for on and another for off, this time well use just one button.
24 Page 24 of 80

Make a copy of the Auto Button (hold the Ctrl key, then click and drag the Auto Button to create a copy in a new location).
You can also use the reserved word TRUE instead of a 1, and FALSE instead of a 0. TRUE and FALSE are not case sensitive, but uppercase is a common convention used to indicate a reserved word.
Double-Click the new button to access its animation properties, then change the button Text to read On/Off. Click on the Input tab when finished.
In the Up Command edit box replace the current text with Toggle(Pump_1_CMD).
You can also use the Insert button to lookup the Toggle function and paste it into the Up Command.
25 Page 25 of 80

Under the access tab you may notice there is a section called security. This is a very powerful feature in CitectSCADA that allows you to precisely define who can access what. Configuring security is covered in the CitectSCADA Configuration training course.
We will now inhibit the Manual On/Off button from working while the pump is in Auto mode and well add a tool tip on the way to explain this to operators. Click on the Access Tab at the top of the button form. In the Tool tip edit box type Must be in Manual to turn on and off then click the Disable tab (on the vertical tabs).
Click on the Insert icon . Click Insert Tag. Double Click on Pump_1_Mode and Add the text = 0 after the tag. Leave the disabled style as Embossed.
Click OK when youre finished. When Pump_1_Mode is 0 or FALSE (i.e. in Auto) this button will be disabled. The buttons appearance will be altered using the Embossed style to indicate that it is disabled and it will not highlight when the cursor moves over it. The tool tip will still work normally.
26 Page 26 of 80
Creating Graphics Pages, Configuring Symbol Sets

Our control buttons for our pump are now complete. We will now add symbol indicators to show what state the pump is in. These indicator lights will show whether the pump is on or off, and whether it is in auto or manual mode. On the Toolbox click on the Symbol Set Tool.
Position the cursor next to the Manual button, then click to place the symbol on the page. In the ON symbol when edit box type Pump_1_Mode = 1.
Click on the OFF symbol Set button to select a different symbol to display for this state. A new popup form will be displayed, with a list of symbol libraries to the right, and thumbnails of the symbols within the selected library on the left. Scroll down the libraries until you find the Lights Round library, then Click on it to select it. The thumbnails on the left will change.
27 Page 27 of 80

Creating Graphics Pages, Configuring Symbol Sets continued
Select the Grey light by Double-Clicking on it. This will replace the original black light with a new grey light for the off state of the animation.
Repeat this exercise for the ON symbol state, this time selecting the cyan light from the lights round library. Click OK when your configuration of the manual symbol is complete.
Copy the Symbol Set and place the new one next to the Auto button. Again, dont worry about positioning the symbol perfectly as we will align the various objects shortly.
Double-Click the copied symbol to access its animation properties. In the ON symbol when edit box replace the expression with Pump_1_Mode = 0 then click OK.
28 Page 28 of 80

Creating Graphics Pages, Configuring Symbol Sets continued
TIP DIGITAL tag types do not require =1 in their symbol detection logic because CitectSCADA knows that they only have two states corresponding to the two symbol states available. This is a little different to when we were writing commands to the tag and we had to explicitly tell CitectSCADA which state to set the DIGITAL tag to.
Make a third copy of the symbol set and position it next to the On/Off button. In the On symbol when edit box replace the text with Pump_1_CMD. Click the OFF symbol Set button and select the Red light from the lights round library, then select the Green light for the ON symbol.
At Runtime, when Pump_1_CMD is on (i.e. equals 1) the Green Light will be displayed, and when it is off (i.e. equals 0) the Red Light will be displayed.
29 Page 29 of 80

Creating Graphics Pages, Aligning Objects
It is worthwhile making your pages look aesthetically pleasing as it will encourage operators to use the system and also makes it faster to find information on the screen. Making sure everything is drawn precisely, aligned correctly and evenly spaced also helps to make your pages look professional. You can align objects manually by dragging them around the screen until you have positioned them satisfactorily, and for which the Grid is an excellent assistant, however sometimes we want to align a group of objects quickly relative to each other. For this we use the Align tool. Select all three buttons by clicking on each of them, while holding the CTRL key down for the last two. All three buttons should have a selection indication at their button left, and be bounded by a large transparent rectangle identified by the four corners, and four center points as shown below.
TIP Another way to select multiple objects is to drag the cursor around them while holding the left mouse button down to lasso the objects. You will need to be careful not to select additional objects if you use this method.
From the Graphics Builder toolbar, select Arrange, and then Align. An alignment popup form will appear, asking you how you would like to arrange the selected objects. Select Left for the horizontal alignment and Even for the vertical alignment, then Click OK.
Repeat this exercise for the lights to the right of the buttons. Try selecting a button and a light and aligning them vertically via the Centre selection before aligning all three lights Evenly. Keep going until you are satisfied with the arrangement of the objects on your screen.
30 Page 30 of 80

Creating Graphics Pages, Aligning Objects continued
You may notice that the lights are not perfectly in line with the center line of the buttons. This is because the hot spot or anchor point for this symbol is in the top left of the symbol rather than in the middle. To correct for this we will use the zoom and the nudge tools. To make sure your objects are aligned or positioned perfectly you can use the Zoom tool. From the Menu select View, Show Zoom.
TIP The Zoom tool can be quickly toggled on and off using the F10 key.
The zoom tool will display an enlarged view of the region around your cursor. You can alter the magnification by clicking in the top left corner of the zoom window
You can move the zoom window by placing the cursor on the title bar (the big blue bar at the top) then hold down the left mouse button and move the mouse.
You can change the magnification of the zoom by clicking on the pop-ups window icon, and selecting to Zoom In or Zoom Out as required.
You can change the size of the zoom window by placing the cursor over one corner until the resize cursor is shown, then hold down the left mouse button and move the mouse.
31 Page 31 of 80

Creating Graphics Pages, Aligning Objects continued
Since the lights are in the correct position relative to each other, we will select all the lights so that we can move them together as a group. Place cursor above and to left of top button; hold down left mouse button and move mouse, then release mouse button to lasso all three buttons. If you have the Grid tool turned on, press F8 to disable the Snap to Grid function, otherwise the buttons will only move to the nearest grid position. You can now precisely position the lights by placing the cursor over the selected objects (make sure the hand cursor appears) then press Enter (or hold down left mouse button), next use the arrow keys on the keyboard to move the buttons one pixel at a time in the direction that you want. Use the zoom box to see exactly where the objects are positioned to the nearest pixel. Press enter again to set the position (or release left mouse button if you used that method).
TIP Windows XP style buttons have a grey border around the button. If you do not want a grey background for your buttons it is suggested that you uncheck the XP Style option under the Appearances tab of your buttons.
Save your page.
Creating Graphics Pages, Formatting with Rectangles

Next we will create a grey background to highlight our control panel. Press F8 to turn the Snap to Grid selection back on. On the Toolbox click on the Rectangle Tool. Click and drag to place a rectangle around your buttons and lights.
Once the rectangle is positioned, you can easily resize it by clicking and dragging the bounding boxes in each corner, and the center of each side.
32 Page 32 of 80

Creating Graphics Pages, Formatting with Rectangles continued
TIP Once a shape has been created you can click and drag the node points (1 per corner and 1 per side), to modify its size and shape. TIP Holding the Ctrl key down while sizing a rectangle or oval forces the object to have the same vertical and horizontal dimensions. This allows you to easily create squares and circles respectively, rather than rectangles and ovals.
When the Rectangle Properties dialog popup appears, change the Style to Solid, the Corner Radius to 4, the Line Color to Grey, and the Fill Color to grey as shown below.
When you are finished, click on the 3D Effects vertical tab on the right-hand side of the form.
Select Lowered from the various 3D Effects available, and retain the default depth and color options, then click OK.
33 Page 33 of 80

Creating Graphics Pages, Formatting with Rectangles continued
The rectangle should now cover all of your buttons and lights, obscuring them from view. We need to send the rectangle to the back layer to allow the buttons and lights to appear in front of it. Select the rectangle by clicking on it, then click the Send-to-Back button Arrange, then Send to Back from the menu bar. or alternatively select
Your page should now look similar to the above. Save your page.
34 Page 34 of 80

Testing Graphics Pages, Computer Setup Wizard
Its time to test your configuration and see how your page looks and feels to an operator. Firstly however, we need compile the project to make sure we have not made any configuration errors, and then we will run the CitectSCADA Computer Setup Wizard to configure how you want this computer to behave within your overall CitectSCADA network. Switch to the Citect Project Editor using Alt+Tab. From the File menu, select Compile. Alternatively you can use the compile button on the menu bar.
The Computer Setup Wizard is typically run only once per project for each computer on which CitectSCADA will run.
You should see a compilation progress bar, followed by a Compilation Success popup.
If your compilation fails, you can double-click on an error from the list provided to take you directly to the location of the incorrect configuration, or you can review your work using this document to ensure that you have performed all steps correctly.
35 Page 35 of 80

Testing Graphics Pages, Computer Setup Wizard continued
We will now setup our Computers role within the CitectSCADA network. Switch to Citect Explorer using Alt+Tab. In the Project List tree make sure the Tutorial project is selected. In the menu bar, click the Computer Setup button.
Check Express Setup then click Next.
Click the Project Name Drop Down and select Tutorial, then click Next.
36 Page 36 of 80
Testing Graphics Pages, Computer Setup Wizard continued
Check Server and Display Client, then click Next. Make sure you left the Multi-Process box unchecked.
Multi-Processing is used to distribute server tasks across multiple CPUs and cannot be used without a license key.
Networking enables communications from this CitectSCADA node to other CitectSCADA nodes on the network. It cannot be used without a license key.
Change the networking selection from the default of Discovery to No Networking, and then click Next. This will isolate this CitectSCADA on the network to allow it to run as a Stand-alone system.
Click Finish.
We are now ready to run our project and test our controls.
37 Page 37 of 80

Testing Graphics Pages, Runtime
Press the Run
button. The Runtime Manager dialog will appear, showing the startup process and status.
If you have not inserted a protection key you will see the following message:
Click OK to run the project in demonstration mode.
The default startup page contains a number of menu items which can be configured in runtime. To configure the page navigation portion of this menu, click on Pages. Click Update Page List on the Pages menu will force CitectSCADA to update its runtime menu to include any unlisted (eg. new) pages. Click it now.
Returning to the Pages menu you will now see your page included in the navigation menu. Click on MyPage now.
Your page will now display.
Testing Graphics Pages, Runtime continued
38 Page 38 of 80
Click on the Manual button then the Auto button and check to see that the appropriate light turns cyan. Also check that the On/Off button becomes unavailable for selection whilst in Auto mode. Move the mouse over the On/Off button and wait a couple of seconds to see that the tool tip appears. See what happens if you click on the On/Off button. Click on Manual, and then try clicking on the On/Off button again. If youve made it to this point, give yourself a gold star and take a moment to stretch your muscles.
39 Page 39 of 80

Creating Graphics Pages, Analog Indicators & Controls
To switch from runtime back to Graphics Builder, press Alt+Space together, then click on Graphics Builder.
Select the grey rectangle you have already created and copy it by dragging it and holding the Ctrl key down on your keyboard (alternatively use standard windows copy and paste controls). Position it to the left of the existing rectangle and drag the resize nodes to change it to a tall, narrow rectangle as shown below. Use the Zoom and nudge, Align, or Grid tool to precisely position the Rectangle in line with the existing rectangle.
Double-click the rectangle to access the rectangle properties form. Select the Appearances tab on the horizontal tabs, and the General tab on the vertical tabs. Change the Filled Color to bright green. Check the Gradient Fill option and select bright red as the Gradient Color. From the pull-down options, change the Gradient Direction to vertical.
40 Page 40 of 80

Creating Graphics Pages, Analog Indicators & Controls continued
Once finished configuring the rectangles appearance, click on the Fill tab and select Level from the vertical tabs on the right-hand side of the form. Use the Insert button to insert the tag Pump_1_Speed. Change the Background Color to black then click OK.
This rectangle will fill and change color as the pump speed increases. The range for the analogue value (0 to 500 RPM), is automatically derived from its tag definition that we built earlier. Next we will create a slider to allow operator control of the pump speed when it is in manual mode.
41 Page 41 of 80

You will need to know the how far (in pixels) the slider needs to move. To find this out select the gradient rectangle (bounding boxes will appear), and look at information provided in the status bar at the bottom right corner of the Graphics Builder. This status bar will show you the width and height of the selected object. Write down the height of the rectangle.
NOTE: If the status bar is not visible, go to the View menu on the menu bar and click on Show Status Bar. On the Toolbox click on the Paste Symbol tool.
When the Symbol selection popup appears, use the scroll bars to locate the xp_sliders library and then Click on it to select that library.
Double Click on right_normal to place it on the page.
42 Page 42 of 80

Position the pointer at the left bottom side of the gradient rectangle using Zoom and Nudge or the Align tool. Double Click on the Pointer Symbol to open the Symbol Properties form. Click on the Slider Tab, then click on the Vertical Tab on the right-hand side. Use the Insert button to insert the Pump_1_Speed tag. Note that if the Continuous update of tag option is checked, then the tag will be written to while it is being dragged. In the At Maximum edit box type the height in pixels that you wrote down earlier. Click OK.
Now is a good time for a regular page save. Click the save icon. You can compile, and run the project again to test these changes before continuing to the next chapter. If CitectSCADA is still running from your previous test, you will need to compile and change pages before updates are picked up by the running system.
Advanced exercise: If youre feeling adventurous, you can add a disable function to the slider (just like for the on/off button), under the Access tab.
43 Page 43 of 80

Creating Graphics Pages, Configuring Text
We will now place some static text above the buttons to label the controls. Click on the letter A on the Toolbox. Type Pump 1. Note: If you do not see the letters that you type it is most likely because the currently selected color is the same as the background color of the page. Place the cursor above the buttons and click to position the text that you have typed. An appearance form will be displayed to allow further customization of the text. Select Bold, font size 22 (point) and change the Foreground color to orange. Click OK.
Flashing colors must be specifically assigned to the default palette. This means that the total number of flashing colors available to you is restricted to 80, which is more then enough for most projects. To create a flashing color, firstly click on the palette location you wish to assign it to, then click Add. Select Flashing from the check-box options. Select the first color (On State color). Click on Off State. Now select the second color. The palette will display the color as two triangular colors in the one square, just like those on the bottom row of the palette (see picture on next page). Colors will not flash in development mode only in runtime.
Creating Graphics Pages, Creating Colors

CitectSCADA supports True Colors. This allows far greater flexibility when importing images, as well as managing colors quickly and easily. The default palette contains 128 commonly used colors however this does not restrict the number of colors you can actually use in your project. Double-click on the Pump 1 text on your graphics page to open the Text Properties form again. Click on the Foreground color.
NOTE: If you have upgraded from a previous version of CitectSCADA and used Flashing Color labels, you will need to reassign those labels to new palette flashing colors as the old method of flashing colors is no longer supported.
44 Page 44 of 80

Creating Graphics Pages, Creating Colors continued
Click on Edit. Another color form will display, allowing you to customize the color either using the mouse, or by entering the RBG indices for specific values.
Flashing colors
You can use a variety of options in this color editing dialog to adjust the color to any of the 32 million true colors available (provided your computer supports 32bit colors). In our case, we will simply Slide the Shading Cursor on the right-hand side up to a very pale shade, then click OK to finish and transfer the new color to your graphics object. Once you are satisfied with the color of your text we will add a 3D Effect of Black Shadowing using the 3D Effects tab on the right side of the Text Properties dialog popup.
Save your page.
45 Page 45 of 80

Creating Graphics Pages, Configuring Numbers
On the Toolbox, click on the number tool. Click to place the number below the gradient rectangle.
The Number tool is actually the Text tool. When you access it via the number tool icon you are presented with the Display Value sheet instead of the General Appearance sheet.
Use the Insert Tag button to enter the tag Pump_1_Speed. Leave the data format field to the default, and the format you specified in the tag definition will be used.
Click on the General tab on the right-hand side and set the font to Black, 12 point, then Click OK.
Creating Graphics Pages, 3D rectangles

46 Page 46 of 80

Next well add some cosmetics to make the display more appealing. Draw a large rectangle that covers all the things you have drawn so far (or copy the one you already have on the page). Set the Line color to Light Grey (see next page). Check the Filled check-box and set the Filled color to Light Grey also. Set the Corner Radius to 8, and activate the Gradient Fill with a medium grey hue.
Click on 3D Effects tab and select Lowered. Since it will be difficult to see your work with the large rectangle in front of it, we need to send it to the back.
Make sure the new rectangle is selected, then click on the Send to Back button menu. on the Tool Bar, or select Send to Back from the Arrange
Click OK when finished.
47 Page 47 of 80

Creating Graphics Pages, Pumps & Piping
Next we will add a picture of the pump and some piping. Click on the Symbol Set tool. Click below the new rectangle to place the symbol set on the page.
Click on the Set button next to the OFF Symbol edit box to change the Off symbol from a black light to a red pump. In the Library list, use the scroll bars to scroll down and then click on pump_base_xlarge. In the Symbol window, Double Click on the left_red symbol.
Click on the Set button next to the On Symbol edit box to change the On symbol from a red light to a green pump. Using the same technique as above, locate the left_green pump then Double Click on it. Use the Insert button to insert the tag Pump_1_CMD. Click OK.
48 Page 48 of 80

Creating Graphics Pages, Pumps & Piping continued
Configuration of the pumps animation is now complete. We now need to add source and destination receptacles along with accompanying pipework and the page will be complete. Click on the Static Symbol Tool in the ToolBox.
Using the scroll bars, locate the tanks cylindrical symbol library, and then Double Click tank_wide_large. Click and drag the tank to position it on the left-hand side of the page.
Repeat for a second tank, this time using the tanks_cyl_conb_30 library, with the tank_large symbol, positioned on the right side of the page, above the pump.
49 Page 49 of 80

Click on the Pipe Tool in the ToolBox. The Pipe tool generates 3D rendered polylines with node points that identify bends or junctions. Pipes can be color filled the same as any other drawing object in CitectSCADA, and will render the flooded color in 3D. We will now draw two separate pipes, one from the source tank on the left side of the page, and one to the destination tank on the right side of the page.
To draw the right-hand pipe: 1. With the pipe tool selected, Hold down the Ctrl Key (Forces only horizontal and vertical lines to be drawn) 2. Place cursor on top of the right-hand tank in the approximate center, click and hold down the left mouse button and move mouse downwards. Release mouse key when you have moved far enough to draw the first leg of the pipe. 3. Move mouse to the left (release the Ctrl Key to allow diagonal pipes if you wish), and click again to create the second leg in the pipe. 4. Continue until you are satisfied with your pipes route and Double Click to end the pipe at the pump.
Note that you can return and adjust the individual junctions of the pipe to fine-tune its position and shape later.
Release the Ctrl Key when you are finished the pipe and the pipe properties form is displayed. Select a pipe highlight color of light grey and a width of 12, and then click OK to close the pipe properties form.
50 Page 50 of 80

To adjust the pipe, select it by clicking on it. The ends and bends of the pipe will have small nodes shown, which can be clicked on and dragged to reposition them. Bounding boxes allow the dimensions of the pipe to be adjusted, and will scale the pipe accordingly, and will not adjust the width of the pipe. Carefully manipulate your pipe to align with the outlet of the tank, and feed into the pump approximately halfway through its radius. Repeat this process to create another pipe on the left-hand side of the pump feeding into the second tank. Dont worry if you add a small section to one end of the pipe when you double-click as the pump or tank symbol will conceal it once we push them to the back layer. Once you are satisfied with the position and shape of both pipes, select both pipes by holding down the Ctrl Key and clicking on each pipe. Release the Ctrl Key. Click the Group button on the tool bar (or select Group from the Arrange menu). on the tool bar (or select Sent to Back from the Arrange menu).
When items are grouped, double-clicking on them will access the group configuration, however objects inside of the group can have their own animation properties independently of the groups properties. To access the individual objects within the group, hold the CTRL key down while double-clicking the object.
Click the Send to Back button
Double Click on either of the pipes that you have drawn. You will notice that the configuration dialog displayed is for Group Properties rather than Pipe Properties. All configurations you now perform will apply to all objects contained within the group, in this case, the two pipes.
Click on the Fill Tab. Insert Pump_1_CMD tag into the ON color edit box. Set the Off Color to light grey and the On Color to Green. Click OK. Your configuration of the pipe work is now complete. Save the page.
51 Page 51 of 80

Your graphical configuration for this tutorial is now complete. You can test this by running the project again, and then continue to the following sections which address color management, alarm handling, and trending, as well as customizing the navigation menu and Administration Tools. If youd like to practice the skills you have just learned, try adding a bar graph to the tank to indicate level (you can add a slider to simulate a level transmitter).
52 Page 52 of 80

Creating Graphics Pages, Managing True Colors
CitectSCADA comes with two excellent tools for adjusting colors, making it very easy to manipulate images from shades of red to green to yellow and so on, even for very complex true-color images. We will manipulate a simple image in this example, but the same principles apply to any true color image that you create or import to the application. Click on the left-hand Tank symbol to select it. From the Edit menu, select Cut Link. This will sever the symbols link with the library and allow us to manipulate it as a stand-alone object. If we did not sever this link, then we would have to modify the object in the library rather than on the page, which would distribute the change to all instances of the object throughout the project. Note that you should never modify the libraries that are supplied with the product. If you require a variation of these objects, you should copy them into your own library, and create the variations there.
From the Tools menu, select Swap Colors.
Creating Graphics Pages, Managing True Colors continued
53 Page 53 of 80
Making sure that the Swap Range option is selected, select any shade of grey for the From Color, and any shade of purple for the To Color, then click OK. The tank should now be a 3D rendered purple variation of the original grey object.
For more flexible color management, you can use the Adjust Colors tool, also available from the Tools menu. This tool allows you to select from a flexible range of colors for migrating from one hue to another, as well as adjusting saturation and darkness at the same time. This can be very useful when one color range does not translate well to another. Use the Adjust Colors tool to change your purple tank to green, and darken the hue by 20%.
54 Page 54 of 80

Accessing Alarm and Trend Display Pages
CitectSCADA comes with a number of pre-built pages. If you do not specifically define these pages in your project to create your own look and feel, then CitectSCADA will use its defaults instead. This includes: Alarm Summary Alarms Disabled Alarms Hardware Alarms Trends Double Trends Popup Trends Instant Trends Administration Tools
Unlike other SCADA packages, Citects Digital Alarms support a combination of two variable tags for alarming purposes. This makes it easy to mask alarms via a second PLC flag (eg. area in maintenance mode), without writing additional PLC logic.
As well as the page template which we are already using which provides built-in navigation and alarm shortlist features. These pages provide comprehensive functionality and can be accessed directly from the navigation menu provided at the top of each page, or via the alarm icons at the bottom left of each page. However to make these pages useful, we must first define some alarms and trends in the project.
Configuring Alarms
Switch to Citect Project Editor (click on the Alarms, then click on Digital Alarms. icon or use Alt+Tab keys). In the Project Editor Menu click on
Fill in the Digital Alarms form for a single alarm as shown below. Remember it is better to use the drop downs to ensure data is entered correctly. When the form is complete click Add. Remember that pressing Enter will add another record to your alarm list, so make sure the form is complete first, or use the Add button.
Configuring Alarms continued
55 Page 55 of 80
TIP In the Variable Tag fields, you can place an expression (eg. Pump_1_Mode = 0) to reverse the alarm detection logic.
Click on the
icon to close the Digital Alarms form when you are finished.
Configuring Trends
Now we need to configure a trend tag to store trend data. Switch to Citect Project Editor (click on use Alt+Tab keys). On the Project Editor Menu, click on Tags then click on Trend Tags. icon or
Fill in the Trend tag form as below then click Add. Remember to use drop downs where possible.
Privilege levels are unique by default, not hierarchical. This means that a user with privilege level 6 does not automatically get access to level 5 functions. If you want your users to have access to more than one privilege level, then you should include all of those levels in the privilege field as shown in the configuration examples. To change the behavior of the system to hierarchical privileges, refer to the online help.
Configuring Trends continued
56 Page 56 of 80

This configuration will log the Pump_1_Speed to disk every second. Most installations would typically log the majority of their data at 2 seconds or slower except for their key operating parameters. There are many more trend features available in Citect. Press F2 with this form open to see some of the advanced possibilities. Pressing F2 again will return you to the basic menus. Click on the icon to close the Trend Tags dialog.
Configuring Security
Most projects require secure user authentication before they will allow control activities to be executed from the HMI. In Citect this can be achieved via local users, or Windows users. In addition to any security that we might configure on our own objects, we also need to define security login credentials to access all of the functionality available from the built-in pages supplied with Citect. Switch to the Citect Project Editor. On the Project Editor Menu, click on System then click on Users.
Fill in the User form as below then click Add.
Local users are managed from within the Citect configuration environment. Windows users (refer Roles below) are managed from either the Windows operating system, or a networked domain server.
Configuring Security continued
TIP There are additional options for security allocations. Press F2 to view the additional parameters available for Users and Roles. Global privileges assign access rights across all areas of the project.
57 Page 57 of 80
The password fields contain * to hide passwords from prying eyes. Do not type *, instead type citect into this field. The asterixes or hidden characters will appear as you type. This user has been configured for maximum security privileges throughout the project and will be able to access the advanced tools available from the navigation bar. We will also add a Windows Administrator group, and a Windows Restricted user with fewer privileges. On the Project Editor Menu, click on System then click on Roles.
Configure the Windows Administrator group to have full access across all areas of the project, similar to the kernel user we have just added.
Configuring Security continued
You can replace individual instances of found items by clicking on them and selecting Replace. TIP If a graphics page is open when changes are made to it using the replace feature, you will need to manually save the page to persist the changes.
58 Page 58 of 80
Add the Windows Users group to have access to privilege level 1 across all areas of the project.
Click the close
button when you have finished.
Using Find and Replace

We are going to perform rework on the variable tag Pump_1_CMD. We are going to change its name to Pump_1_RUN to better represent its function. Rather than searching the entire project for each place this tag is used, we are going to use the project search and replace feature to perform this exchange for us. Switch to the Citect Project Editor. In the Project Editor Menu, click on Edit then click on Replace (or use Ctrl-R).
Using Find and Replace continued
59 Page 59 of 80

Type Pump_1_CMD in the Find box, and Pump_1_RUN in the Replace with box. Make sure Current Project is selected, along with all search options checked. Click Find.
The utility will display a list of all locations where the Pump_1_CMD tag is found. Click Replace all. Confirm the replace when prompted, and (if you still have the page open), switch to the graphics builder to save changes to your page. Congratulations. You have completed the offline configuration portion of this tutorial. The following sections show you how to configure the online portions of the project.
60 Page 60 of 80

Runtime
Now its time to run your project and test it to make sure that you have completed the tutorial correctly. Compile your project, then Click on the Runtime icon.
Use the back button at runtime to go back through the pages that you have visited.
Use the navigation menu to access your graphics display called MyPage. Click on Auto button then click On Manual. Click On/Off. You will see that both pipes change color as the group properties you configured will be applied to everything in the group, in this case both pipes.
You will also see an alarm is generated and displayed on the alarm bar at the bottom of the page when you switch to Manual mode. The Alarm icon at the bottom left will flash to indicate that you have new, unacknowledged alarms. Click on this Alarm icon to view the Alarm page.
61 Page 61 of 80

Runtime continued
Windows users local to the Citect PC can use the login name directly, but domain users will require the domain name, followed by a backslash, then the user name.
If you try to acknowledge the alarm from the alarm menu at the top left of the screen, or by right-clicking on an alarm, you will notice that you do not have access to these features. By default you require a privilege level of 1 to use these features. Click on the Logon button or pull-down menu on the navigation bar. This will produce a Login form in which you can enter your user name and password as shown below. Use the local Citect user we created called kernel, with a password of citect. Alternatively, if you know your local computer admin account, or domain admin account, you can login using those credentials as shown in the second example below.
OR
If your login was successful, you should see the logged in user name at the top right of the page. The alarm acknowledge functions will now be available to you.
62 Page 62 of 80

Runtime continued
Once logged in, try accessing the alarm acknowledgement features again. This time they will work. You will notice that the alarm changes color once acknowledged, and disappears when you return the pump to automatic. If the pump returns to automatic and you have not acknowledged the alarm, it will remain on the screen until you do acknowledge it. This ensures that the operator never misses an alarm incident.
63 Page 63 of 80

Runtime, Trends
Trend Groups configuration can also be accessed from the Admin Tools option under the Tools menu.
From the navigation menu, select Configure Trend Groups from the Trends navigation menu.
Type in a name for your first trend group, nominally Pump_1. Then use the build buttons to add Pump_1_Speed to the group.
When you are finished, click Add, then close the window by clicking on the Now select Single Trend from the Trends navigation menu.
icon
to select a trend group for display. By manipulating the pump speed via the Use the Trend Groups button slider on MyPage, you should now see the trend value changing on the graph. There are many powerful features available on this page, including: Trend cursor describe each pen at that location History mode Zoom in/out Allows you to quickly and easily access historical data Allows you to quickly and easily zoom the trend graph by highlighting an area and pressing the zoom button Scaling Allows you to change the minimum and maximum ranges for each pen Export Allows you to export raw time-stamped data to the clipboard or a file Click and slide along the graph to locate the cursor which displays tool-tips to
64 Page 64 of 80
Runtime, Trends continued
Take some time to get used to these features as they are key components to assisting you in analyzing and interpreting your production information.
65 Page 65 of 80

Runtime, Process Analyst
CitectSCADA has facility for viewing trends and alarms. The Process Analyst is an ActiveX object that can be embedded on your own page, or you can use the default page provided. Click on the Process Analyst configured. Click on the Add Pens button to display this page. Initially this is an empty container ready to be
The Process Analyst can have many display panes. Each pane supports both digital and analogue pens. To create multiple panes, you will need to customize the toolbar so that the Add Panes button is available to you (see the Online Help). Alternatively, you can create a new pane each time you are selecting new pens for display.
button.
Click on Search to find all configured trend pens. Select the Pump_1_Speed pen and click Add. Now change the Type from Trends to Alarms. Repeat your search and select Pump_1_Mode from the alarm list. Click Add then, when you are finished, click OK.
A new display pane will be added to the page displaying both the Pump_1_Speed analogue pen as well as the Pump_1_Mode digital alarm pen. If the gridlines do not appear, click on the graph area and it will refresh the display. Experiment with some of the control buttons (described on the next page), or click-and-drag on the graph itself to move through history.
66 Page 66 of 80

Runtime, Process Analyst continued
Display/remove pen cursor. Once displayed, click and drag the cursor to reposition it on the graph.
Display/remove pen cursor labels. Once displayed, click and drag them to reposition them on the graph.
Toggle the object pane at the bottom of the page which lists display pens. This creates more room for the graph pane.
Toggle Auto-Scroll.
Zoom in 50%
Zoom out
Zoom using a click-and-drag zoom box
We will now modify the appearance of the Process Analyst display. Click on the Properties
button.
67 Page 67 of 80

Interpolation is the manner in which the display shows links between sample points. Straight means that it draws a line directly between two points. Stepped means it holds the last sample value until it reaches the time of the new sample, and then steps to the new value. Stepped interpolation is a more accurate indication of the samples that Citect SCADA has recorded.
Expand the tree to Pane 1 and modify the background color. You can select from the color palette, or create new palette items by entering the Red, Green and Blue values directly. In this case, enter 250, 250, 190, for Red, Green and Blue respectively, then click Add to Custom Colors. Select this new color and click OK to record the change. Click Apply to see the effect on your Process Analyst view. Now select Pump 1 Speed in RPM beneath Pane 1 in the properties tree.
Change the line color to bright red and the width to 2, and the interpolation from Straight to Stepped. Click OK to see the effect on your Process Analyst view and close the properties window.
68 Page 68 of 80

Finally, resize the Object pane to maximize the graph pane while still showing the list of pens.
Your Process Analyst view is now complete, but before you leave the page, click on the Save button. This will allow you to save the Process Analyst configuration you have just entered, and retrieve it again later on. Fill in the file name and click Save. This will allow you to return to this view quickly at a later time button. using the Load View
69 Page 69 of 80

Administrative Tools
CitectSCADA comes with a number of commonly used administrative and debugging tools built into its default menu. Select Admin Tools from under the Tools menu. If you are not logged in, the menu options will be greyed out and inaccessible.
Understanding the
CitectSCADA Kernel and other advanced debugging utilities are covered in the CitectSCADA training courses.
If required, login as the Administrator as shown previously using either the kernel user, or a Windows Administrator user. Once logged in with the appropriate privilege level, the Admin Tool menu will change color to blue and become accessible. As well as access to common applications and file management tools, this page also allows access to System Setup (The Computer Setup Wizard), runtime and communications statistics, and online menu configuration.
70 Page 70 of 80

Administrative Tools, Configuring the Menu
In the Citect Configuration box, select Configure Menu.
Expand the menu system by clicking on each + item. Each menu Button is a separate pull-down menu on the navigation bar. By right-clicking on each item, you can modify the items in its pull-down menu.
Right-click on Pages under the Generic node. Select Delete Button from the available options. This will remove the entire Pages pull-down menu. We will now create our own Pages menu.
71 Page 71 of 80

Administrative Tools, Configuring the Menu continued
Menu Configuration allows the following types of items to be added to the menu: New Page Items under new Pages will only be available when the user is looking at a page of the same name. This allows menu items to be hidden unless on a particular page. New Button Adds another button to the navigation bar allowing additional pull-down menus to be created. New Item Adds an item into the pulldown menu of a Button. New Sub-Item Extends pull-down menus to have child-menus which will appear when selected from the parent menu.
Right-click anywhere in the left-hand pane and select New Button from the available options.
Right-click on this new Button and select New Item from the available options.
Right-click on this new Item and select Edit Item from the available options. Type MyPage as the Action, and select True from the pulldown list for the Checked option. Click OK.
Actions must refer either to the name of a page to display or a Cicode function. If specifying a Cicode function, it must be prefixed by a question mark ("?").
72 Page 72 of 80

Administrative Tools, Configuring the Menu continued
This pull-down item is now configured to display MyPage when it is selected from the navigation bar. Single-click on the New Item, and change its name to My Page.
Single-click on the New Button, and change its name to My Menu.
icon to close the Menu Configuration dialog. When prompted, make sure you save the Click on the changes you have made. These changes will take effect when you next change pages. Select a new page from the navigation bar, and verify that your new menu appears with the new page as shown below.
73 Page 73 of 80

Administrative Tools, Tag Debug
Finally we will look at an extremely useful testing and commissioning tool the Tag Debugger.
Return to the Administration Tools page, and select Tag Debug from the Tools menu.
In the dialog provided, type in Pump_1_Mode (alternatively use the Browse feature to navigate and select the same tag), and then click Read.
If the pump is currently in Manual, the Tag Value should return a 1. If it is Automatic it should return a 0. Verify that the correct value was returned by checking the state of the lights on MyPage. Change the value to the opposite state by typing a 1 or 0 into the Tag Value to replace the value that was read. Click Write. Verify that the new value was written to the tag both by clicking Read again, and by checking the state of the lights on MyPage.
WARNING Tag Debug is a powerful utility that can access any tag in the CitectSCADA system and both verify its state/value as well as change it. As such, it should be used with caution, especially when changing values for tags which control equipment!
74 Page 74 of 80

Backing Up Your Project
It is important to keep backup copies of your project, so that you can always recover from a disaster with minimum effort.
Make sure you are in the Citect Explorer (click on the selected.
icon or use Alt+Tab), and have the Tutorial project
Click on the Backup icon
Use the Browse button to locate a directory where you want to save your files to. Alternately you can type the directory and filename into the Backup File edit box. If the directory does not exist CitectSCADA will automatically create it for you when it saves the file. Click OK and when the Backup Complete message pops up, click OK on that also.
75 Page 75 of 80

Restoring Your Project
With any software, it is good practice to check and make sure you can restore from your backup copies. It is very rare to experience problems restoring from a CitectSCADA backup but the time taken to check is a tiny fraction compared to the time it would take to recreate the project from scratch.
Click on the Restore icon
(it is next to the backup icon), on the menu bar click Tools then Restore.
Click on the Browse button to locate your backup file. We will restore to a new project, test it, and then delete it, as this is a much better test than restoring over the existing project and less chance of anything going wrong (eg; what if the power fails half way through restoring over the top of your existing project or your backup has a fault in it?). Make sure New Project is checked. In the Name edit box type a name for the new project e.g; TutorialTest then click OK. When the restore is completed (click OK on the Restore Complete Dialog), click on the TutorialTest project to switch to that project, then change to the Citect Project Editor to compile the project before clicking on the Computer Setup Wizard and repeating the Setup steps identified earlier in this tutorial to configure the computer to run the Tutorial Test project in stand-alone mode. Make sure you have shutdown the Tutorial project prior to attempting to run the TutorialTest project.
76 Page 76 of 80

Restoring Your Project continued
Click on the Citect Runtime icon was successful.
to make run your project and prove your backup and restore operation
To delete the TutorialTest project, click File on the Citect Explorer menu, then click Delete Project.
Congratulations! By now you should have a basic working knowledge of CitectHMI/SCADA software. If you are keen to build your level of competency we recommend that you attend a Citect Training Course. Details of training courses can be found at www.citect.com or by contacting your local Citect office or distributor.
77 Page 77 of 80

Troubleshooting
If you experience results that are different to what you see in the tutorial 1. Go back and double check what you have done. Most likely you have done something different from the instructions. 2. The tutorial largely assumes CitectHMI/SCADA is freshly installed and default settings havent been changed. By taking a closer look at the screens in the tutorial you may be able to identify any differences. 3. 4. If problem is in Runtime, shutdown runtime and restart it. Read the Online Help. Most dialog boxes have a help button that provides context sensitive information with just a mouse click. 5. Read the CitectHMI/SCADA knowledgebase. This is available on the CitectHMI/SCADA software CD or from our website www.citect.com. 6. Worst case, start again, just create a new project and call it Tutorial2. The upside to this is the extra practice will make you more proficient. If nothing appears to happen when you press a button, do not press it repeatedly in the hope that something will happen chances are your PC is busy trying to do what youve already asked it to do.
78 Page 78 of 80
Addendum Security Validation

CitectSCADA V7.10 contains additional security functions to make it easier for companies to implement electronic signatures and multi-user validation. This last exercise will modify the Pump 1 manual button to require signature validation before setting the Pump_1_Mode value to 1.
Switch to the Graphics Builder click on the Graphics Builder icon
Open your MyPage graphics display, and double-click on the Manual button to access its animation properties. Click on the Input tab, and modify the command to: MultiSignatureTagWrite("Pump_1_Mode", "1", "", "kernel", "", "", "")
Save your page. Switch to the Citect Editor and compile your project. Run your project. Once the project is running, open MyPage, and click on the Manual button. Instead of immediately changing the pumps mode to manual, Citect will display an electronic signature verification form. Click on the Verify button.
Addendum Security Validation continued
79 Page 79 of 80

A new verification form is displayed, prompting for the kernel users password. This will display even if the kernel user is already logged in. Type in the kernel users password citect, then Click OK.
A final verification form is displayed, allowing the user to verify that the action should be performed.
Click Approve. The pump mode will now be changed to Manual.
Further information on electronic signatures and user validation can be found in the online help.
80 Page 80 of 80

Tutorial Citec

Uploaded by

Copyright:

Available Formats

Tutorial Citec

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tutorial Citec

Uploaded by

Copyright:

Available Formats

Quickstart Tutorial V7.

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

= Press left mouse button twice quickly

= Briefly press right mouse button

= A tick or cross in an options box

= Type in the word Text

Click and drag

Quickstart Tutorial V7.10

Citect Explorer Top level configuration interface

Citect Draw Used for creating graphics

Citect Runtime Provides the active operator interface

You can switch between these applications by:

Quickstart Tutorial V7.10

On the Tool Bar, click on the New Project icon

Quickstart Tutorial V7.10

saved or closed in the Graphics Builder before changing projects.

Quickstart Tutorial V7.10

Close the Clusters window by clicking on the

Once marked for deletion the record will be ignored.

Quickstart Tutorial V7.10

We can identify these computers by TCP/IP address, or computer name.

The universal loopback

address 127.0.0.1 is only appropriate for standalone systems with no clients.

Quickstart Tutorial V7.10

Configuring Clusters continued...

Quickstart Tutorial V7.10

Configure an I/O Device

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Data Type Address

Quickstart Tutorial V7.10

Data Type Address

Data Type Address Raw Full Scale Eng Full Scale

RPM Format ###.#EU Pump 1 Speed (0 500 rpm)

Quickstart Tutorial V7.10

Creating Graphic Pages

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Click on the Save icon on the menu bar

Type MyPage in the Page edit box, then press OK.

Quickstart Tutorial V7.10

Now we are ready to create and position our graphics objects.

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Creating Graphics Pages, Configuring Buttons continued

In the Insert Tag Dialog Double Click on Pump_1_Mode.

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Creating Graphics Pages, Configuring Symbol Sets

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10

Quickstart Tutorial V7.10