Scribd
Upload
3K views3 pages

Cswip Question Paper

This document contains a 17 question multiple choice quiz on welding topics for the CSWIP 3.1 certification. The quiz covers subjects like welding processes, electrodes, non-destructive testing methods, heat treatment, welding defects, and welding procedure qualification. It also lists 7 theory questions that were asked on the CSWIP 3.1 exam in February 2007 related to welding inspector duties, electrode specifications, hard stamping limitations, TIG welding, hydrogen cracking factors, and welding procedure tests.

Uploaded by

antonyfernandof
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views3 pages

Cswip Question Paper

This document contains a 17 question multiple choice quiz on welding topics for the CSWIP 3.1 certification. The quiz covers subjects like welding processes, electrodes, non-destructive testing methods, heat treatment, welding defects, and welding procedure qualification. It also lists 7 theory questions that were asked on the CSWIP 3.1 exam in February 2007 related to welding inspector duties, electrode specifications, hard stamping limitations, TIG welding, hydrogen cracking factors, and welding procedure tests.

Uploaded by

antonyfernandof
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

CSWIP 3.

1 Quiz
Multi-Choice and Questions 1. Which of the following is the correct statement?
AC and DC can be used for MMA AC and DC can be used for TIG AC and DC can be used for SAW All of the above

Paper
Feb 2007

2. A weld of dissimilar material is termed as. Compound weld Transition weld Complex weld All of the above

3. What will you do if you find a consumable core wire is having rust on the surface? Baking before use It is not important Rust should be completely removed by wiping with wool before use Quarantine for further investigation

4. What is High Frequency used for some welding process? To reduce arc strike To give deep penetration For controlled arc To control interpass temperature

5. Why Slope In technique is used for TIG? To reduce spatter To reduce tungsten inclusion To give arc stability All of the above

6. Which of the following is a Rutile electrode? 6010 6013 6018 6016

7. Arc blow is associated with which of the following processes? MMA TIG SAW None of the above

8. What is added to steel for Deoxidation. Sulphur Phosphorus Silicon Manganese

Printed On : 5/16/2010 @ 21:31:57 a5/p5

Page 1 of 3

CSWIP 3.1 Quiz


Multi-Choice and Questions

Paper
Feb 2007

9. Fillet Fracture Test is conducted to.


Assess the strength Assess the root penetration and fusion Assess fracture failure Assess the toughness

10. Welding procedure qualification is To give welder practice To give instruction

11. Which effect does the cyclic loading have on a member?


Reduce strength Reduce Fatigue life Reduce toughness All of the above

12. Why hard stamping is not allowed on some welding fabrication? It is too slow It can be safety hazard It may be damaging to the material All of the above

13. Which NDT method is effective for identifying laminations? Radiography Test Magnetic Particle Test Ultrasonic Test Dye Penetrant Test

14. MIG/MAG welding has a tendency to give lack of sidewall fusion when Spray transfer conditions are used 100% CO2 shielding gas is used Pulsed current is used Dip Transfer conditions are used

15. During PWHT of a complex fabrication, the heating rate and cooling rate are much higher than specified. This may. Cause excessive oxidation Not allow sufficient time to relieve stresses Introduce excessive compressive stresses Cause Distortion

16. A low heat input welding will have reduced.


Printed On : 5/16/2010 @ 21:31:57 a5/p5

Page 2 of 3

CSWIP 3.1 Quiz


Multi-Choice and Questions
Toughness Strength Residual Stress Harness

Paper
Feb 2007

17. As the voltage of X-Ray set increases. It increases the penetrating power It increases the wave length It increases the image quality All of the above

Theory Questions Asked in February 2007:


1. Explain your Duties as a Welding Inspector? Give a Mandatory Reference Compulsory Question 2. As per BS 639 : 1987 E 44 42 R (13) a. What gives Strength, Toughness and Position b. Covering c. Other characteristics 3. Why Hard Stamping is not used for some welding fabrications? 4. Explain TIG Processes. 5. Give four factors responsible for Hydrogen Cracking. 6. What is the requirement of Welding Procedure Test. Give 5 Essential Variables? Define Essential Variable. 7. Explain Lamellar Tearing. Note: The following is not exactly as it came in the exams (especially the multi choice). In general, there is a lot of twist in the questions asked.

Printed On : 5/16/2010 @ 21:31:57 a5/p5

Page 3 of 3

You might also like