Refrigeration Fundamentals & Sealed System Diagnosis
L2005-022PPT
1
Refrigeration
Refrigeration is best defined as the movement of heat from a location where it is not wanted to a location where the added heat will not matter. Refrigeration works because there is a relationship between Heat and Pressure
Heat and pressure behave in a predictable ways By controlling pressure, we can control heat
Heat
Everything has heat Without heat, all molecular activity would stop (Absolute Zero) Heat is measured two ways
Heat Intensity (Thermometer) Heat Quantity (BTUs)
Heat
One BTU is equal to the heat generated by burning common wooden kitchen match
Heat Intensity (Temperature)
BTU (British Thermal Unit) Quantity
Heat Quantity
Heat Packet
Wood Table Top
Metal Leg
75 F Environment
Even though two items can be at the same temperature, some materials will contain more heat (heat packets) than others.
5
Heat Transfer
BTU BTU
100 F
BTU
50 F
Heat travels from an area of higher heat concentration to an area of less heat. The great the temperature differential, the faster the heat transfer.
BTU
BTU
-5 F
BTU
-15 F
Even in temperatures that we consider cold, heat still moves.
Heat Movement
Con o uc t i d n
Heated air rises and is replaced with cooler air
Convection
Cooler air falls and repeats cycle.
Glass
7
Radiation
BTU Transfer
Super heated vapor
Latent Heat of Vaporization Latent Heat of Fusion
(only under pressure)
One BTU is = to heat generated by burning a common kitchen stick match
Intensity and Quantity
212 F 212 F
Even though both the water and steam are at 212 F, the steam has 970 BTUs (per pound) more heat than the liquid (more heat packets)
Pressure Effect on Boiling points
Superheated vapor
212 F
Under pressure, the water and vapor temperatures will increase well beyond the normal 212 F boiling point at sea level. Heat quantity rises as well.
Adding heat to a liquid causes it to vaporize
Cooling the vapor causes it to condense back into a liquid
11
Evaporation
Water wicks through the porous ceramic to the exterior of the vessel. There, the water evaporates (changes state).
Porous ceramic container
Water
Your body relies on this same principle to keep you cool. In a warm environment, your body sweats. The sweat evaporates and cools your skin.
As the water changes from a liquid to a vapor, heat is absorbed. This cools the walls of the vessel which, in turn, cools the water.
12
Intensity and Quantity
The key take aways from the boiling water example is:
In order for a change of state to occur, heat must be added or taken away. With water, 970 BTUs of heat must be absorbed to effect a change of state from a liquid to a vapor. Conversely, the same 970 BTUs of heat must be removed from that vapor before that vapor can change back into a liquid. Boiling is just an exaggerated form of evaporation
13
Pressure
Pressure is Relative
At sea level, pressure is 14.7 PSI Pressure drops with Altitude Pikes Peak
Altitude Pressure
Denver Boston Chicago LA
14
212 F
75 F
To Vacuum Pump Reducing the pressure over a liquid lowers its boiling point
15
Hg scale
Mercury (Hg) Tube
16
Hg Scale
As pressure is increased over the open Mercury, the level of liquid within the mercury tube rises
17
Hg Scale
Conversely, as pressure is reduced over the open Mercury, the level of liquid within the mercury tube falls
18
Hg Scale
By measuring the number of inches of Hg in the tube, we can determine the pressure over the liquid. In weather reporting, atmospheric pressure is also known as barometric pressure. Changes in barometric pressure usually precedes a change in weather.
Normal Atmospheric pressure is 29.92 Hg
19
PSI Scale
PSIA 96.7 92.2 PSIG 82 77.5
Normal Atmospheric Pressure
Absolute Pressure
Gauge Pressure
14.7 0
14.7 PSIA
0.0 PSIG
.5 0
28.9 29.2
At Sea Level
20
PSI Scale
In refrigeration, pressure is relative. Since pressure is all around us, any measurements we make are referenced to normal atmospheric pressure. At sea level, the normal 14.7 PSIG pressure that surrounds us becomes the zero reference point for our refrigeration gauges.
PSIA
96.7 92.2
PSIG
82 77.5
14.7
.5 0
28.9 29.2
Compound Gauge Set
At Sea Level
21
Positive and Negative Pressures
PSIA 96.7 92.2 PSIG 82 77.5
Pressure that are greater than normal atmospheric pressure are called positive pressures and are measured in P.S. I. Gauge. Pressures that are less than normal atmospheric are called partial vacuums and are measured in Inches of Mercury (Hg).
Positive Gauge Pressure
14.7
Negative Gauge Pressure (Partial Vacuums)
.5 0
28.9 29.2
At Sea Level
22
Negative Pressure (Partial Vacuums)
A perfect vacuum is measured as Zero PSI on the absolute scale or negative 29.92 inches of mercury (Hg) on a refrigeration gauge
Measuring Pressure & Vacuums
Low side gauge High side gauge
Low Side Hose (Blue)
Compound Gauge Set
High Side Hose (Red)
Common Hose (Yellow)
Measuring Pressure
P r e s s u r e
26
Gauge Markings
Low Side Gauge
Atmospheric Pressure
PSIG Pounds per Square Inch Gauge
R-134a
Negative Pressure (Vacuums)
27
Gauge Markings
Low Side Gauge
This is read as 50 PSIG
Negative Pressure (Vacuums)
R-134a
This is read as a 20 Inch vacuum
28
Partial Vacuums Can also be Measured in Microns
A micron is a thousandth of an inch. A total of 29,920 microns of pressure would have to be removed to achieve a perfect vacuum (zero microns).
Charles Law
At a constant temperature, the volume of a gas varies directly with pressure.
30
Charles Law
At a constant volume, the pressure of a gas varies directly with temperature.
31
Charles Law
At any given temperature, the contents of a cylinder will strike a balance between how much vapor and liquid exists within the tank
Vapor
Liquid Liquid
This is know as the Steady State of a liquid in a storage vessel
Charles Law
Temperature
Pressure
Charles Law
Temperature
Pressure
Charles Law
Just as increasing pressure increases the temperature, decreasing pressure decreases temperature
Pressure
Temperature
Charles Law
Because of the pressure/temperature relationship outlined in Charles law,
if we know the temperature of a liquid in a sealed container, we can determine the pressure the liquid is under
if we know the pressure, we can determine the temperature
lowering the pressure reduces the boiling point of a liquid increasing the pressure raises the condensation point of a vapor
36
Pressure Affect on Boiling points
212 F
To Vacuum Pump 75 F
Under reduced pressure, water will boil at normal room temperatures or below
Pressure
Pressure Affect on Boiling Point of Water
Temperature
284 234 184 134 84 34
10 2 6
14
Atmospheric Pressure
334
18
22
26
30
At 0 PSIG, water boils at any temperature above 34 F and condenses at any temperature below 34 F
29.92 in Hg 19.74 in Hg
PSIG
11.6 in Hg
0
PSIG
1.4 PSIG
5 PSIG
10 PSIG
15 PSIG
34
20 PSIG
Refrigerants
Class of chemicals with extremely low boiling and condensing points
R-134a
R-22
39
R-134a Boiling and Condensing Points
- At seal level, R134a boils at any temperature above -15 F
R-134a
75 F 212 F
-16 F
Because of its extremely low boiling point, R-134a boils normal room temperatures. The warmer the temperature, the more violently the refrigerant boils
40
Finding Steady State Pressures and Temperatures
Refrigerant Temperature Refrigerant Temperature
PSIG
R-12
R-22 R-134a R-502 R-410A
PSIG
R-12
R-22 R-134a R-502 R-410A
0 2 4 6 8 10 12 14 16 18
-22 -16 -11 -7 -2 2 5 9 12 15
-41 -37 -32 -28 -24 -20 -17 -14 -11 -8
-15 -10 -5 -1 3 7 10 13 16 19
-50 -45 -40 -36 -32 -29 -25 -22 -19 -16
-60 -58 -54 -50 -46 -42 -39 -36 -33 -30
105 110 115 120 125 130 135 140 145 150
93 96 99 102 104 107 109 112 114 117
62 64 67 69 72 74 76 78 81 83
90 93 96 98 100 103 105 107 109 112
54 57 59 62 64 67 69 71 73 75
34 36 39 41 43 45 47 49 51 53
41
T/P Gauge Markings
Low Side Gauge
Refrigerant Temperature Scales
R-134a
How refrigerants make refrigeration possible
Because refrigerants boil at very low pressure and temperatures, they absorb heat even in sub zero environments
Since R134a boils at any temperature above -15F (0PSIG), it can remove heat from a freezer compartment that is at 0F
Because of their pressure/temperature condensation points, they give up heat even in warm environments
Under normal sealed system operating conditions, R134a will condense at any temperature below 100F
43
How refrigerants make refrigeration possible
By controlling pressure, we can control the boiling (evaporation) and condensation points of a refrigerant
Lowering pressure reduces the boiling point Increasing pressure raises the condensation point
By setting up pressure differentials within a Sealed System, we can control the temperatures at which the refrigerant will boil (evaporate) and condense
44
Tying it all together
In ANY refrigeration system, refrigerant is alternately evaporated, absorbing heat) and condensed (giving up the heat)
Evaporation occurs in low pressure side of the system Condensation occurs in high pressure side of the system Compressor and capillary set up pressure differentials
45
Components of a Typical Sealed System
Condenser Filter Drier Capillary Tube Evaporator
Heat Exchanger
Suction line Compressor
46
How Compressor Increases Pressure
To Cond To Cond
On the intake stroke, vapor refrigerant from the low side of the system is pulled into the compression chamber
On the exhaust stroke, the refrigerant is pushed out of the compression chamber and into the high side of the system
How Compressor Increases Pressure
To Cond
48
How the Drier Creates a Restriction
porato To Eva
From C on d e nser or larger
As the liquid droplets enter the drier, the smaller cap tube restricts their flow into the condenser
Cap Tube .030 or smaller
Refrigerant Flow
Condenser Filter Drier Capillary Tube
Heat Exchanger
Low Pressure Evaporator
Suction line Compressor
High Pressure
50
How Refrigerant Absorbs Heat
Evaporator
51
How Refrigerant Absorbs Heat
High pressure liquid travels from the condenser, through the capillary tube and enters the evaporator
High pressure liquid from cap tube
The lower pressure of the evaporator drops the boiling point of the liquid and the refrigerant begins to evaporate (boil)
52
How Refrigerant Absorbs Heat
As the refrigerant boils, it pulls heat from the coil and the vapor becomes Superheated (contains trapped heat)
High pressure liquid from cap tube
When the coil in that area drops to -15F, the refrigerant can no longer exist as a vapor and condenses back into a -15F Liquid The latent heat that the refrigerant absorbed during evaporation is now trapped in the -15F liquid
53
How Refrigerant Absorbs Heat
As each section of the coil drops to -15F, the superheated vapor condenses back into a liquid
High pressure liquid from cap tube
54
How Refrigerant Absorbs Heat
This process continues until the entire coil is down to -15F and the evaporator is completely filled with liquid This condition is referred to as a Flooded Evaporator The -15F can now continue to absorb heat without any further evaporation taking place
55
How Refrigerant Absorbs Heat
Eventually, the only place where evaporation is taking place is the the very end of the coil (Evaporator outlet) The super heated vapor now travels through the heat exchanger back to compressor
S
56
Heat Exchanger
This cools the liquid refrigerant before it enters the evaporator.
er ns de n Co
U LIQ
ID
t ea H
m Fro
T ap C t ea H
e ub
t ea H
t ea H
t ea H
ion t uc S
ine L
OR P VA
As the vapor travels through the suction line, it continues to absorb heat.
Heat Exchanger
or ess r mp Co To
It also warms the vapor and insures that no liquid enters the compressor.
57
How Refrigerant Releases Heat
Static Condenser Drier
58
How Refrigerant Releases Heat
The combination of the higher condensing temperature and the cooler air moving across the coil causes the refrigerant to condense. In the process, the refrigerant gives up its latent heat. Liquid droplets travel to the drier
59
How the Drier Creates a Restriction
porato To Eva
From C on d e nser or larger
As the liquid droplets enter the drier, the smaller cap tube restricts their flow into the condenser
Cap Tube .030 or smaller
How Refrigerant Releases Heat
Liquid begins to pool and backs up into the condenser.
How Refrigerant Releases Heat
Once the drier fills with liquid, the liquid begins to pool back into the condenser
62
How Refrigerant Releases Heat
The condenser begins to fill with liquid Eventually, the last few passes of the condenser are liquid filled. This reservoir of liquid insures that there is enough refrigerant in the system to maintain a flooded evaporator
63
Condensers
Forced Air
Warm Wall
Static
64
Evaporators
Tube an Fin
Shelf
Roll Bond
65
Gas Loops (Yoder lines)
66
Condenser Loop Refrigerant Flow
Post Condenser Loop
General Refrigeration Rules
Under normal conditions, low side and high side pressures follow one another.
If high side pressure goes up, low side pressure follows If low side pressure goes up, high side pressure follows
68
General Refrigeration Rules
Heat load has greatest effect on low side pressure
As heat load increases, both low and high side pressures go up As heat load is decreased, pressures go down
Ambient conditions has a greatest effect on high side pressures
As ambient temperature rises, condenser temperatures increase Higher condenser temperatures mean higher low side temperatures and pressures and reduced ability to absorb heat
69
General Refrigeration Rules
Compressor running wattage reflects how much work the compressor is performing How much work the compressor is doing is dependent on heat load and ambient conditions
70
Sealed System Diagnosis
71
Constant State
Condenser
Evaporator
Normal Conditions
High Side (Condenser) Pressure: About 120 to130 PSIG
Running Amperage Approximatel y 1 amp (Ranges from .6 to 1.4 Amps depending on Compressor BTU rating)
Liquid level varies but normally last couple of passes of condenser is filled with liquid when running Evaporator frosted from top to bottom
Low Side (Evaporator) Pressure: About 0 PSIG (Ranges between 10 and 5-7 lb PSIG)
Charging
(Cooling Capacity) 1000 950 900 850 800 750 700 650 600
75 80 85 90 95 100 105 110 115
BTUs
Amp Draw
1.4 1.3 1.2 1.0 .9 .8 .7 .6 .5
Percent Correct Charge
74
Refrigeration Diagnosis Dos and Donts
Do
Check internal and external air flow Check refrigerator and freezer temperatures Check for unusual heat sources
Light staying on Air leaks into freezer or refrigerator sections
Dont
Assume a system problem unless youve eliminated all other possible causes
Air flow Heat load Customer usage
Check that defrost system is working properly Check current draw Feel compressor, condenser for proper temperatures
Tap into system unless you are absolutely sure that the problem is with the sealed system
75
Low Side Leak- Refrigerant still left in the system
HS pressure: Depends on Air/Refrigerant ratio* Cond Temp: Depends on Air/Refrigerant ratio* LS Pressure: Lower than normal Evap Temp: Warmer than normal
Condenser
Low Current Draw
Low liquid level Evaporator Ice ball on first pass (passes) of evaporator
* Condenser pressure and temperature will depend on volume of non-condensables absorbed into the system
Low Side Leak- Air in system
HS pressure: Very high Cond Temp: Very hot
Condenser
LS Pressure: Atmospheric Evap Temp: Warm
High Current Draw
No liquid
Evaporator No frost on evaporator
High Side Leak
HS pressure: Lower than normal* Cond Temp: Cooler than normal*
Condenser
LS Pressure: Lower than normal Evap Temp: Warmer than normal
Current Draw ** Low Watts
Liquid Level
Evaporator
Frost ***
* Liquid level will depend on how much refrigerant still left in system
**Compressor run wattage, pressures and temperatures of Evaporator and Condenser dependent on how much refrigerant is left in system. ***Frost on Evaporator and liquid level in condenser depends on how much refrigerant left in the system
Restriction
HS pressure: Ambient Cond Temp: Ambient LS Pressure: Vacuum Evap Temp: Warmer than normal
Condenser
Low Current Draw
Condenser full of liquid
Evaporator
No Frost on evaporator
Inefficient Compressor
HS pressure: Lower than normal Cond Temp: Cooler than normal LS Pressure: Higher than normal Evap Temp: Warmer than normal
Condenser
Low Current Draw
Liquid level low or non existent
Evaporator
Little or o Frost on evaporator
Inefficient compressor (defective exhaust valve)
To Cond
Because the condenser is under higher pressure than the dome of the compressor, most of the refrigerant is pulled back from the condenser on the down stroke
Inefficient compressor (defective intake valve)
To Cond
Because the condenser is under higher pressure than the dome of the compressor, most of the refrigerant is pushed back into the dome rather than the condenser
Undercharge
HS pressure: Lower than normal Cond Temp: Cooler than normal
Condenser
LS Pressure: Lower than normal Evap Temp: Warmer than normal
Low Current Draw
Low liquid level Evaporator
No frost on last pass (or passes) of evaporator
Overcharge
HS pressure: Higher than normal Cond Temp: Hotter than normal LS Pressure: Higher than normal Evap Temp: Slightly Warmer than normal
Condenser
High Current Draw
High liquid level
Evaporator
Frosted suction line all the way back to compressor
Conditions When Pressure/Temp/Watts Dont Follow One Another
Low Side Leak- Non-Condensables in high side
High side pressureLow Side pressureWatts High side pressureLow Side pressureWatts
Inefficient Compressor
85
Sealed System Analysis
Indicators
Conditions
Watts Condenser Temp Condenser Liquid Frost Line Level Capillary Tube Low Side Sound Pressure High Side Pressure Pressure Equalization Rate
Overcharge
Undercharge Low-Side Leak -Refrigerant in System Low-Side Leak- NO Refrigerant in System High Side Leak Low Capacity Compressor Restrictions Capillary Tube (Complete) Capillary Tube (Floating)
Sealed System Analysis
Indicators
Conditions
Watts Condenser Temp Condenser Liquid Level Frost Line Capillary Tube Low Side Sound Pressure High Side Pressure Pressure Equalization Rate Normal to slightly longer Quicker than Normal
Overcharge
High
Higher than Normal Higher than Normal Lower than Normal Lower than Normal Normal to Slightly Higher * Lower than Normal
All the way back Louder than to suction line Normal Partial Intermittent
Higher than Normal Lower than Normal
Higher than Normal Lower than Normal
Undercharge
Low
High* Low-Side Leak -Refrigerant in System
Partial to Non Intermittent to existent (possible non existent frost ball) Non existent
None
Normal to slightly Normal to Normal higher* slightly higher than Normal * Atmospheric Higher than Normal Normal
Low-Side Leak- NO Refrigerant in System High Side Leak Low Capacity Compressor Restrictions Capillary Tube (Complete) Capillary Tube (Floating)
High
High
None
Low Low
Low Low
Low to non existent Low
None Partial to Non existent
None Intermittent to non existent
Vacuum Higher than normal
Low Lower than Normal
Quicker than Normal Quicker than Normal
Low Low
Low Low
Higher than normal Higher than Normal
None Intermittent
None Intermittent
Vacuum
Ambient
No equalization Intermittent
Intermittent Partial Intermittent Vacuum lower than normal
*Compressor run wattage and the pressures and temperatures of Evaporator and Condenser dependent on how much refrigerant is left in system.
Restricted Evaporator Air flow
HS pressure: Lower than normal Cond Temp: Cooler than normal LS Pressure: Higher than normal Evap Temp: Slightly Warmer than normal
Condenser Condenser
Low Current Draw
Low liquid level
Evaporator
May be frosted all the way back to compressor
Restricted Condenser Air Flow
HS pressure: Higher than normal Cond Temp: Warmer than normal LS Pressure: Higher than normal Evap Temp: Slightly Warmer than normal
Condenser
High Current Draw
Normal liquid level
Evaporator
Normal Frost Pattern
Conditions that Mimic Sealed System Failures
Indicators
Conditions
Watts Condenser Temp Frost Line Capillary Tube Sound Low Side Pressure High Side Pressure Fresh Food Temp Freezer Temp
Plugged condenser Blocked Cond. Fan Blocked Evap Fan Evap Iced up (defrost failure) High heat load High ambients Damper failed closed Damper failed open
Conditions that Mimic Sealed System Failures
Indicators
Conditions
Watts Condenser Temp Frost Line Capillary Tube Sound Low Side Pressure High Side Pressure Fresh Food Temp Freezer Temp
Plugged condenser Blocked Cond. Fan Blocked Evap Fan Evap Iced up (defrost failure) High heat load High ambients Damper failed closed Damper failed open
High High Low Low
Higher than Normal Higher than Normal Lower than Normal Lower than Normal Higher than Normal Higher than Normal Lower than Normal
Full Full Frost back to compressor Frost back to compressor Full Full Full
Normal Normal Normal Normal
Higher than Normal Higher than Normal Lower than normal Lower than normal Higher than normal Higher than normal Lower than normal Lightly higher than normal
Higher than Normal Higher than Normal Lower than Normal Lower than Normal Higher than normal Higher than normal
Warmer than Normal Warmer than Normal Warmer than Normal Warmer than Normal Warmer than Normal Warmer than Normal
Warmer than Normal Warmer than Normal Warmer than Normal Warmer than Normal Warmer than Normal Warmer than Normal Cooler than Normal Warmer than Normal
High High Low
Normal Normal Normal
Lower than normal Warmer than Normal Slightly higher than normal Cooler than Normal
Slightly higher Slightly higher than Normal
Full
Norma;
Be Aware, Be Alert Always work safely. On the Job, On the Road, In the Home Every Time, All the Time
92
