Huawei BTS3900A Installation Guide V1.0

Security Level: Internal Open
7pt ite
0pt
nt :
um nd
Mobitel Stage4 Huawei BTS3900A Installation Guide V1.0

2008.9
www.huawei.com Liu Jiang 60307
rs :
rial
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
5pt B0 nt : um ers nd rs : rial
2G BTS3900A(outdoor)
APM30 for power and BBU Battery cabinet: 184Ah*2
2pt -5: 8pt ck nt : um ers nd rs : rial
RF cabinet for 6 DRFU
The layout of the BTS3900A is as shown in the picture. The APM30 and RF cabinet should be near to the cable ladder. Two battery cabinet should stack.
Huawei Confidential
Page 2
Outlook of BTS3900A
BTS3900A cabinet
Stacked Battery cabinet
Huawei Confidential
Page 3
The plinth
The BTS should be installed on the steel rack or concrete plinth For the steel rack, use the bolt and nut to fix the base frame of cabinet. For the concrete plinth, use the expansion blot to fix the base frame.
Huawei Confidential
Page 4
Install the base
Fix the base to the plinth and check the levelness with level bar, if the level bar is not in the middle, use the adjusting pad to adjust the levelness 2 base need to be installed, one is for BTS3900A, one is for battery cabinet
Huawei Confidential Page 5
Install the cabinet
Push the cabinet so that the cabinet can be in full contact with the installation block Use two bolts to fix the cabinet to the base
Huawei Confidential
Page 6
Install the component

PMU BBU
PSU
Special handle is needed to remove the DRFU
Install the BBU, DRFU, PMU and PSU to the cabinet as shown in the picture. The BBU should be close to the PDU panel, without space between PDU and BBU
DRFU
Huawei Confidential
Page 7
Connect the DC cable for BBU and DRFU
Load5
Connector to UPEU on BBU DC power cable for DRFU
Connect the DC cable to the Load5 of the PDU with OT terminal. Blue cable as 48v, and black as 0 V. Connect the power terminal to the UPEU card on BBU. Connect the power cable to the corresponding DRFU, 6 cables to 6 DRFU. The other end is already connected.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 8
Install the CPRI cable for DRFU
GTMU DRFU
CPRI cable
Connect the CPRI cable between the GTMU and DRFU, the 6 ports on GTMU should be connected to the corresponding DRFU. The port on DRFU should be port0 The CPRI cable route should be at left side of the cabinet, as show in the picture
Install E1 cable
UELP
GTMU
There are two E1 cable, one is between GTMU and UELP, the other is from UELP to MW The cable between GTMU and UELP is already made.
GTMU
UELP
MW
Huawei Confidential
Page 10
RF cable
Upper 6 jumper to be installed Usually, the lower 6 jumper is not needed
S2
S2 PBT S3 S4
Usually, one cabinet has 6 jumpers, please refer to the picture for the jumper and RF cable connection. One end of the jumper is straight DIN connector, the other end (BTS side) is right angle DIN connector. The connectors need to be made on site. The configuration of the cell is as showing in the picture:S2, S2 PBT, S3, S4
Stack two battery cabinet

Wiring cover
cover
Step 3
Step 1
Step 2
Step1:Install the lower cabinet and remove the cover Step2:Install the wiring cover to the lower cabinet Step3:Seal the wiring cover with mud. Step4:Install the upper cabinet on top of the lower cabinet, fasten the upper cabinet with 4 bolts.
Step 4
Huawei Confidential
Page 12
Install the battery

Install the DC cable to APM30 Install the DC cable between upper and lower battery
Upper battery cabinet
Lower battery cabinet
Battery breaker
Use the black DC cable as 48V, and red DC cable as 0V. 2 battery banks to be installed in each cabinet. Attention! Switch off the battery breaker in battery cabinet and APM30 when installing Battery terminal the battery!
Install the grounding cable
ECB inside the cabinet Install the PGND cable from APM30 to ECB Install another 2 pcs of equipotential cable from APM30 to upper battery cabinet and lower battery cabinet
Connect the AC input cable
PDU
short circuit bar
Install the 4 x 4mm^2 armored cable to the terminal of PDU, L1,L2,L3,N: brown, black, grey, blue. When 3 phase power is used, the short circuit bar should be removed; when single phase power is used, install the short circuit bar. AC power cable should be protected in the GI pipe , and the armor of the cable should be grounded with the hose clip
Lay the AC power cable

Dig a channel between meter cubicle and plinth. Lay the AC power cable with the protection of GI pipe. Flexible GI pipe should be used as bend. The armor of the AC cable need to be grounded. Ground the GI pipe with M8 x 25mm bolt & nut, using 25mm^2 grounding cable Bury the pipe
Dig the channel and lay the AC cable

Make the bend with the Gi flex pipe

Huawei Confidential
Ground the AC cable armor with the hose clip

Page 16
Install the SPD for BTS
Install the SPD box on the meter cubicle, the SPD should be grounded.
Huawei Confidential
Page 17
Alarm Cable
FMUA(COM)------BBU(MON0)
BBU(MON0)
FMUA(COM IN)
Connect the BBU(MON0) and FMUA(COM IN) with the cable(04070023)

Alarm Cable
DPMU(COM)------APMI(J1)
One end of the cable is already connected to J1 port of APMI, the other end need to be connected to COM port of DPMU
Alarm Cable
DPMU(RS422)------APMI(RS422)
One end of the cable is already connected to RS422 port of APMI, the other end need to be connected to RS422 port of DPMU
Huawei Confidential
Page 20
Alarm Cable
BBU(MON1)------APMI(TX- TX+,RX- RX+)
Wire White Orange Blue White One pair One pair Port on APMI TX+ TXRX+ RX-
One end of the cable(04080029) is to MON1 port of BBU, another end need to be cut and connect the wire to the panel of APMI (TX- TX+,RX- RX+), The connection is as shown in the table.
Install battery sensor cable
One end of the battery sensor cable is already connected to the APMI card BAT_TEM1 port, so connect the other end to one cell of the battery.
Connect the door sensor cable
Socket to connect the 2 sensor
Connect the door sensors of the two battery cabinets and the APM30 as red line shown in the picture Connect the sensor cable to the socket of the prior door sensor, so the connection of the 3 door sensors are serial
Huawei Confidential Page 23
Antenna system installation
Huawei Confidential
Page 24
Antenna system installation

Ground the feeder cable according to the standard in the picture Antenna azimuth and down tilt should follow the design file strictly. All the jumper connectors are waterproofed well. The feeders are arranged neatly, the feeder and jumper labels are attached neatly and oriented in the same direction. Use feeder clamp to fix the feeder each meter.
Huawei Confidential
Page 25
Installation check key point

Check the grounding cable of cabinets, SPD, Gi pipe, AC power cable, feeder. Check the water proof of the feeder and antenna connector. Check AC and DC power cable color code, complied with the standard. The cable should be tied neatly. Keep redundancy when cutting the cable tie. Antenna height, azimuth and down tilt should follow the design file strictly. The signal cable and battery cable outside the cabinet should be protected with PVC flexible pipe. All the cables should be labeled with the label provided. Bring back the rest of the materials and clean the sites after installation.
Huawei Confidential
Page 26
Power on the cabinet
AC input Breaker
DC output Breaker
Step1:Switch off all the AC and DC breaker Step2:Power on the AC input breaker, check the indicator of the PMU and PSU, For PMU, if RUN is 1s on and 1s off, and ALARM is off, it mean the module is working normally For PSU, if the is on, and is off, it means the module is working normally
Step3:Use the multimeter to measure the DC output voltage, the normal range should be -38.4V to -57V. Step4:Switch on the DC output breaker for the related module, switch on the DC output breaker on the DCDU
Commission the BTS

LIU1
Connect the E1 cable to MW, check the indicator LIU1 on the GTMU, if its always off, it means the E1 is normal. After the BTS is on air, make some test call, check the cell broadcast service and GPRS service. The following alarm need to be checked on site: Door alarm of all the 4 cabinets Water sensor of the cabinet Temperature and Humidity Battery sensor Mains failure and PSU failure
Huawei Confidential
Page 28
Thank you
www.huawei.com

Huawei BTS3900A Installation Guide V1.0

Uploaded by

Copyright:

Available Formats

Huawei BTS3900A Installation Guide V1.0

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Huawei BTS3900A Installation Guide V1.0

Uploaded by

Copyright:

Available Formats

Security Level: Internal Open

Mobitel Stage4 Huawei BTS3900A Installation Guide V1.0

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

APM30 for power and BBU Battery cabinet: 184Ah*2

2pt -5: 8pt ck nt : um ers nd rs : rial

RF cabinet for 6 DRFU

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

2pt -5: 8pt ck nt : um ers nd rs : rial

Stacked Battery cabinet

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

2pt -5: 8pt ck nt : um ers nd rs : rial

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

Install the base

2pt -5: 8pt ck nt : um ers nd rs : rial

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

Install the cabinet

2pt -5: 8pt ck nt : um ers nd rs : rial

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

Install the component

2pt -5: 8pt ck nt : um ers nd rs : rial

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

Connect the DC cable for BBU and DRFU

2pt -5: 8pt ck nt : um ers nd rs : rial

5pt B0 nt : um ers nd rs : rial

Install the CPRI cable for DRFU

2pt -5: 8pt ck nt : um ers nd rs : rial

5pt B0 nt : um ers nd rs : rial

2pt -5: 8pt ck nt : um ers nd rs : rial

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

2pt -5: 8pt ck nt : um ers nd rs : rial

5pt B0 nt : um ers nd rs : rial

Stack two battery cabinet

2pt -5: 8pt ck nt : um ers nd rs : rial

HUAWEI TECHNOLOGIES CO., LTD.

5pt B0 nt : um ers nd rs : rial

Install the battery

2pt -5: 8pt ck nt : um ers nd rs : rial

Upper battery cabinet

Lower battery cabinet

5pt B0 nt : um ers nd rs : rial

Install the grounding cable

2pt -5: 8pt ck nt : um ers nd rs : rial

5pt B0 nt : um ers nd rs : rial

Connect the AC input cable

2pt -5: 8pt ck nt : um ers nd rs : rial

short circuit bar

5pt B0 nt : um ers nd rs : rial

Lay the AC power cable

2pt -5: 8pt ck nt : um ers nd rs : rial

Dig the channel and lay the AC cable

Make the bend with the Gi flex pipe

Ground the AC cable armor with the hose clip