100% found this document useful (1 vote)
1K views

Sim Reader

This document provides information about the TiVald Sim Interface v1.0, which can be used in two modes: SIM-READER mode for reading and writing SIM cards, and PROGRAM PIC mode for programming PIC processors in clone SIM cards. It includes details on the interface's connections, components, jumper settings for each mode, and software recommended for each mode, including Sim Scan, Cardinal, FKi2, WinPhoenix, PonyProg2000, IC PROG, CHIP-CAT, and JGPROG-PAP. Clone SIM cards that can be programmed include Gold Card, Silver Card, Green Card, and Black Card.

Uploaded by

Oshan Indrajith
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
1K views

Sim Reader

This document provides information about the TiVald Sim Interface v1.0, which can be used in two modes: SIM-READER mode for reading and writing SIM cards, and PROGRAM PIC mode for programming PIC processors in clone SIM cards. It includes details on the interface's connections, components, jumper settings for each mode, and software recommended for each mode, including Sim Scan, Cardinal, FKi2, WinPhoenix, PonyProg2000, IC PROG, CHIP-CAT, and JGPROG-PAP. Clone SIM cards that can be programmed include Gold Card, Silver Card, Green Card, and Black Card.

Uploaded by

Oshan Indrajith
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

TiVald Sim Interface v1.

0
Sim Interface intended for operation with GSM SIM CARDS, PRE-PAY PHONE CARDS, SAT-TV CARDS, Clone SIM Cards. Sim Interface can work in two modes:
1. SIM-READER - mode intended for reading / writing GSM SIM CARDS, and writing EEPROM 24Cxx inside in a CLONE SIM CARDS (PHOENIX / SMART MOUSE compatible). 2. PROGRAM PIC - mode is intended for programming FLASH / EEPROM Memory in PIC processor inside in a CLONE SIM CARDS (JDM Programmer compatible).
COM PORT USB POWER

14.318 Mhz

POWER SIM DATA SIM RESET MCLR 13V FOR PROGRAM PIC

SIM CLOCK 14.318 MHz 7.159 MHz 3.579 MHz PROGRAM PIC SIM RESET LOW RESET HIGH RESET PROGRAM PIC SIM DATA SIM READER PROGRAM PIC TiVald SIM INTERFACE

SIM CONNECTOR

EXTERNAL SIM CONNECTOR

Vcc RES CLOCK GND DATA

FEATURES:
a

-Compatibility with PHOENIX / SMART MOUSE / DEJAN SIM SCAN / JDM Programmer.

-Reading from GSM SIM CARDS IMSI, KI codes and write them in a clone SIM-CARD. -Reading and writing Phonebook and some parameters GSM SIM CARDS. -Possibility to program PIC processor inside in a CLONE SIM CARDS (JDM Mode). -In-Built converter 5 to 13 v for program PIC. -Possibility to use different frequencies 14.318 MHz, 7.159 MHz, 3.579 MHz at reading SIM CARDS. -LED for indication of a condition of a power supply. -LED for indication of a condition of a SIM DATA. -LED indicating a condition SIM RESET, in a mode of programming PIC indicating presence of voltage 13V on an input MCLR of the processor PIC. -External SIM Connector

OPERATIONAL MANUAL:
a

1. Connect SIM READER to a COM port of the PC. 2. For power supply SIM READER connect it to a USB port of the PC. 3. Establish a jumper SIM CLOCK, SIM RESET, SIM DATA.
a

For SIM READER mode: Set jumper SIM CLOCK in a place 14.318 MHz, 7.159 MHz or 3.579 MHz it is necessary for operation of the majority of the programs. Set jumper SIM RESET in a place LOW RESET or HIGH RESET it is necessary for operation of the majority of the programs. Set jumper SIM DATA in a place SIM READER. For PROGRAM PIC mode: Set jumper SIM CLOCK in a place PROGRAM PIC. Set jumper SIM RESET in a place PROGRAM PIC. Set jumper SIM DATA in a place PROGRAM PIC.

THE SOFTWARE FOR SIM READER:


a

For SIM READER Mode:


a

- Sim Scan v2.01 by Dejan Kaljevic http://users.net.yu/~dejan/ SIM SCAN is a program that allows functionality analysis of Yours GSM SIM smart card. With this program you can analyze: ATR, CLA+INS, FILES, Key. Also, you can write IMSI and Ki to GSM a38 SIM Gold Card (PIC 16f84 & EEPROM 24c16) Finding Ki works on 100% of new SIM cards from 2000-2002 with COMP128-1 ciphering algorithm. Cardinal Software http://www.mfgware.com/ - CARDinal 0.99.110F trial. The software for editing smartcards (mainly SIM cards) with plug-ins system. - Cardinal beta (build 68). The software for editing smartcards, finding IMSI and KI. - FKi2 v2.1. The software for finding IMSI and KI. - WinPhoenix v1.06 http://www.id2.cz/clonecard/winphoenix.zip The software for program EEPROM 24C16 inside in a CLONE SIM CARDS (Gold Card) Operations of the program need a file loader.hex http://www.id2.cz/clonecard/goldcard.zip
a a a a

For PROGRAM PIC mode:


a

- PonyProg2000 ver 2.05a beta http://www.LancOS.com allows to program the PIC processor inside a clone card. The program works under WINDOWS 95,98. For setup choice Setup / Interface Setup. Further it is necessary to select SI Prog I/O and number of a COM port, which you use. As it is necessary Select Polarity of the ontrol lines: Invert D-OUT - ON, Invert D-IN - OFF, Invert SCKL - OFF, Invert RESET - OFF.

For SIM READER & PROGRAM PIC Mode:


- IC PROG ver 1,05 beta http://www.ic-prog.com allows to program the PIC processor inside a clone card, and external EEPROM 24C16 inside a clone card (Smartcard Wisard). The program works under WINDOWS 95,98. For setup push the [F3] key "Hardware settings", select the interface JDM Programmer and number of a COM port, which you use. As it is necessary Select Polarity of the Control lines: Invert Data Out - OFF, Invert Data In - OFF, Invert Clock - OFF, Invert MCLR - OFF. For SIM READER mode setup choice Settings / Option / Smartcard. Further it is necessary to select Frequency 3.58 MHz, type of PIC Pricessor and number of a COM port, which you use. - CHIP-CAT v2.3 http://www.multisat.de/software/chipcat23.zip Allows to program the PIC processor and external EEPROM 24C16 inside a clone card. In setup choice CLOCK 3.5 MHz and number of a COM port, which you use. - JGPROG-PAP by Jg2000 http://www.jg2000.org http://www.vgj.pl/pliki/jgprog_27_12_2002.zip Allows to program the PIC processor and external EEPROM 24Cxx inside a clone card. In setup choice AutoMode JGPAP2 OFF and number of a COM port, which you use.
a a A

CLONE SIM CARD:


a a

You will need to know IMSI and Ki codes of every simcard that you want to make backup. IMSI and Ki codes are the codes that identify a simcard at your network provider, this codes are encrypted at your original simcard SIM EMU http://simemu.cjb.net/ Clone card are of the following types: Gold Card - (PIC16F84+24C16) max. 4 different provider names , 31 phonebook names, 1 SMS Silver Card - (PIC16F876+24C64) max. 8 different provider names, 208 phonebook names, 10 SMS Green Card - (PIC16F876+24C128) max. 8 different provider names, 250 phonebook names, 40 SMS Black Card - (PIC16F876+24C256) max. 8 different provider names, 250 phonebook names, 40 SMS
D1 VCC R1
16

Vcc

1,5k LED POWER D3 D2 LL4148 D4 ZENER13v LL4148 C6 100n

C3 100n

U1 C1+ 1 C2 100n

C1 100nF

V+

R9 1,5K U2-5 JP1 DATA 1 3 D5 2 4

D7 LED DATA

+ C9 3,3m

C10 100nF

XT1

+ C7 3,3m

R10 1,5k U2-2 R11 2,2K U2B 11 10 9 8 Q0 Q1 Q2 Q3 74HC393 CLK MR 13 12 74HC04 C11 22P

14,318 MHz U2-1

4 C4 100n

C2+

C1-

U2-4 6 C5 100n

74HC04 BAR43

VCC J1 1 2 3 4 USB POWER J2 5 9 4 8 3 7 2 6 1 COM PORT

C2-

V-

74HC04

JP2 CLOCK 1 3 5 7 2 4 6 8

74HC04 R12 1M C12 22P

U2-3 13 R1 IN R1 OUT 12 74HC04 14 T1 OUT T1 IN 11

JP3 RESET 1 3 5 2 4 6 SIM CONNECTOR

C8 100n

R2 IN

R2 OUT

9 R5

Q3 BC857

JP1 SIM DATA

7 R2 10k

T2 OUT
GND

T2 IN

10

10K R6 5,6K

1-2 PROGRAM PIC 3-4 SIM READER

R7 6,8K

R8 1k

CLOCK
VCC

DATA
1 3 5 2 4 6

JP2 SIM CLOCK


1-2 3-4 5-6 7-8

15

MAX232 R3 5,6k Q1 BC847 U2-6 R4 5,6K 74HC04 Q2 BC847

14.318 Mhz 7.159 Mhz 3.579 Mhz PROGRAM PIC

RESET Vcc GND

D6 LED

EXTERNAL SIM CONNECTOR

JP3 SIM RESET

1-2 LOW RESET 3-4 HIGH RESET 5-6 PROGRAM PIC

RESET

TiVald Sim Interface

You might also like