OCXO 131-2

Charlottesville, VA USA www.isotemp.com

PHONE: (434) 295-3101 FAX: (434) 977-1849

CRYSTAL OSCILLATOR SPECIFICATION

REV A

DESCRIPTION OF REVISION

BY ADB

APV JRD TST

DATE 10-14-1998 02-28-2002

Put on new form, Added 2.5., 2.7. was TBD, In 3.1. 4x10-7 was 3x10-7, 4.2. was 250 mA, 4.3. was 1 Watt, 7.3. was 125-501

TST

ISOTEMP RESEARCH INC. CODE ID CHARLOTTESVILLE, VA. USA 31785

MODEL NO. OCXO 131-2

PAGE OF TOTAL 1 3

DWG. NO. REV. 114-836 A

OCXO 131-2
Charlottesville, VA USA www.isotemp.com

1. OUTPUT 1.1. 1.2. 1.3. 1.4. 1.5. 1.6.

Frequency Waveform Level Load Harmonics Spurious

10.000 MHz Sine wave +8 2 dBm 50 < -30 dBc < -60 dBc < 2x10-8 from -30C to +70C (referenced to +25C) < 5x10-10/day < 5x10-10 after 30 days < 1x10-7 < 3x10-7 < 5x10-9/5% change < 5x10-9/5% change < 5x10-11/second root Allan variance < 2x10-8 in 5 minutes @ +25C (referenced to 4 hours) < < < < < -120 -135 -150 -150 -150 dBc dBc dBc dBc dBc

2. FREQUENCY STABILITY 2.1. Ambient 2.2. Aging a. At time of shipment b. After indefinite storage i. Daily ii. Yearly iii. 10 years 2.3. Voltage 2.4. Load 2.5. Short term 2.6. Warm-up 2.7. Phase noise a. @ 10 Hz b. @ 100 Hz c. @ 1 kHz d. @ 10 kHz e. @ 100 kHz

3. ELECTRICAL FREQUENCY ADJUSTMENT (PIN = "VCO INPUT") 3.1. Range > 4x10-7 < 9x10-7 (At time of shipment) (Referenced to nominal frequency) 3.2. Control 0 VDC to Vref (+8 VDC) or a 10 k potentiometer connected between the "REFERENCE VOLTAGE" pin and "0 VOLTS & CASE" pin with wiper connected to "VCO INPUT" pin. 3.3. Slope Positive 3.4. Center +4 VDC 0.8 VDC (control voltage at which nominal frequency occurs at time of shipment) 3.5. Input impedance > 100 k

ISOTEMP RESEARCH INC. CODE ID CHARLOTTESVILLE, VA. USA 31785

MODEL NO. OCXO 131-2

PAGE OF TOTAL 2 3

DWG. NO. REV. 114-836 A

OCXO 131-2
Charlottesville, VA USA www.isotemp.com

4. INPUT POWER (PIN = "+VDC") 4.1. Voltage 4.2. Current 4.3. Steady state

+12 VDC 5% < 300 mA @ turn on < 1.5 Watts @ +25C

5. REFERENCE VOLTAGE (PIN = "REFERENCE VOLTAGE"), an output 5.1. Voltage +8 VDC 5% 5.2. Load > 8 k 5.3. Temperature stability < 0.015 VDC (Over temperature range in 2.1.) 6. ENVIRONMENTAL 6.1. Humidity 6.2. Storage temperature 6.3. Vibration (non-operating) 6.4. Shock (non-operating) 6.5. Seal 7. MECHANICAL 7.1. Applicable series 7.2. Model number 7.3. Outline drawing NOTE: MIL-STD-202F, Method 103B, Test Condition A (95% R.H. @ +40C, non-condensing, 96 hours) -50C to +85C MIL-STD-202F Method 201A. (0.06" Total p-p, 10 to 55 Hz) MIL-STD-202F, Method 213B, Test Condition J. (30 g, 11 ms half-sine) MIL-STD-202F, Method 112C, Test Condition D. OCXO 131 series OCXO 131-2 125-587

This specification differs from the OCXO 131-2 listed in the ISOTEMP catalogue in the following areas. 1. The turn on current is 50 mA higher. 2. The steady state power is 0.5 Watts higher. 3. The width is 0.01 inches wider. 4. The length is 0.06 inches longer.

ISOTEMP RESEARCH INC. CODE ID CHARLOTTESVILLE, VA. USA 31785

MODEL NO. OCXO 131-2

PAGE OF TOTAL 3 3

DWG. NO. REV. 114-836 A

PIN CONNECTIONS
PIN
P/N: MOD: FREQ.: S/N: DATE: FSC: 31785

FUNCTION
VCO INPUT
or

(See Note 1)

(VIEW FROM TOP)

(See Note 1)

NOT CONNECTED REFERENCE VOLTAGE

NOT CONNECTED +VDC R. F. OUTPUT 0 VOLTS & CASE

0.75 MAX. 19.05

3 4 5

0.026 0.20 MIN. 0.66 5.08 0.031 DIA. PIN (5 PLACES) 0.79 GLASS STANDOFF (4 PLACES)

Note 1. If the specification does not specify parameters for either PIN1 or PIN2 then that respective PIN is NOT internally CONNECTED.

1.43 MAX. 36.32 1.000 CENT. 25.40 3 4 1.07 0.700 CENT. 27.18 17.78 5

C L

(VIEW FROM BOTTOM)

NUMBERS FOR REFERENCE ONLY (NOT STAMPED ON UNIT)

REV: A SHT: 1 OF 1

DWG: 125-587

OSCILLATORS

CHARLOTTESVILLE, VIRGINIA CODE I.D. NO. SCALE: 1:1 DWN. BY: LRB DATE: 12-04-00 APPR'D. BY: DAG TOLERANCES
UNLESS OTHERWISE SPECIFIED: ANGLES: 1 DEGREE FRACTIONS: 1/32 INCH DECIMALS: .XX .015, .XXX .010 INCHES

NAME: OUTLINE DRAWING

31785

1.07 WAS 1.07 MAX.

DAG TST 12-6-01

LET

REVISION

BY APP

MAT'L: STEEL FINISH: NICKEL DATE MARK: LABEL