Scribd
Upload
46 views4 pages

DSL605EW To Change or Make Wireless Password To Secure Network

1. The document provides instructions for configuring the wireless access point on an AZTECH DSL605EW 4-port ADSL2/2+ wireless router. 2. It describes how to access the router's configuration page via a web browser, then change the wireless network name, enable the access point, and set WEP encryption with a 10-character password. 3. Finally, it explains how to scan for and connect a computer to the wireless network using the new password.

Uploaded by

VInay KuMar Gvk
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
46 views4 pages

DSL605EW To Change or Make Wireless Password To Secure Network

1. The document provides instructions for configuring the wireless access point on an AZTECH DSL605EW 4-port ADSL2/2+ wireless router. 2. It describes how to access the router's configuration page via a web browser, then change the wireless network name, enable the access point, and set WEP encryption with a 10-character password. 3. Finally, it explains how to scan for and connect a computer to the wireless network using the new password.

Uploaded by

VInay KuMar Gvk
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

AZTECH DSL605EW

4-PORT ADSL2/2+ WIRELESS-G MODEM ROUTER

RECONFIGURING THE WIRELESS ACCESS POINT

A. CONNECTING THE WIRELESS DSL605 EW’S ACCESS POINT


1. Connect your computer to any of the Ethernet Ports 1-3 of the DSL605EW
Or
Use computer connected to the router wirelessly.

2. Open your Internet browser

3. On the address box, type http://192.168.1.1 press enter.

Note:

If there’s a prompt for login, try the following

Username: admin
Password: admin

or

Username: admin
Password: (no password)

4. On the main page, click on Wireless

5. On the left panel menu, click on Setup, this will open the Wireless Setup page

P R OD U C T E NG I NE E R I N G A N D S UP P O R T A Z T E C H T E C H N O L O GI E S P T E L T D
Singap o re
Frequently Asked Qu est ion Page 2 of 4

6. On the Wireless Setup page, you must change the Primary SSID, Primary SSID will be the wireless
network name which you will see when you scan for wireless networks from your computer

7. Ensure that there is a check for Enable AP then click on Apply

8. On the left panel menu, click on Security, this will open the Wireless Security page

P R OD U C T E NG I NE E R I N G A N D S UP P O R T A Z T E C H T E C HN O L O G I E S P T E L T D
Singap o re
Frequently Asked Qu estion Page 3 of 4

9. Click to select WEP from the security options

10. Ensure that you have a check mark on the Enable WEP Wireless Security

11. On the Authentication Type, ensure that Open is selected

12. There will be 4 boxes, fill the 1 box with 10 digits (combination of numbers from 0-9 and
st

letters A-F only), cipher for the first box should be set to 64 bits

Now 10 digits is the wireless password

13. Click on Apply

14. To save the settings to the device click on Save Settings click ok.

P R OD U C T E NG I NE E R I N G A N D S UP P O R T A Z T E C H T E C HN O L O G I E S P T E L T D
Singap o re
Frequently Asked Qu estion Page 4 of 4

B. CONNECTING TO THE WIRELESS ACCESS POINT FROM YOUR COMPUTER

1. Restart your computer and switch off and on your router

2. Ensure that the laptop’s wireless switch is turned on.

3. Scan for the available wireless networks from your computer, look for your own wireless
network, connect to your own network and input the required 10 digits wireless password,
will successfull y connect to the internet.

Note:

1. If your computer is already connected to the wireless network and cannot access
the Internet, make sure that the IP address and DNS Server address are obtained
automatically.

For Windows XP:


a. Open Control Panel > Network Connection
b. Right click on the Wireless Network Connection and click on Properties
c. Click on Internet Protocol TCP/IP and click on Properties
d. Ensure that the following are selected
Obtain an IP address automatically
Obtain DNS server address automatically

For Windows Vista or Windows 7:


a. Open Control Panel > Network and Sharing center
b. Click on Manage Network Connection or Change Adapter Settings
c. Right click on Wireless Network Connection and click on Properties
d. Click on Internet Protocol Version 4 (TCP/IPv4) and click on Properties
Obtain an IP address automatically
Obtain DNS server address automatically

P R OD U C T E NG I NE E R I N G A N D S UP P O R T A Z T E C H T E C HN O L O G I E S P T E L T D
Singap o re

You might also like