Scribd
Upload
622 views4 pages

Verilog Code For PLL

This Verilog code defines a PLL module called pll3 that takes an input clock signal inclk0 and outputs a clock signal c0. It uses an altpll component to multiply the input clock frequency by 5 and divide it by 4 to generate c0, resulting in an output frequency that is 1.25 times the input frequency. The altpll component is configured through defparam statements to specify properties like clock frequencies, device family, and which ports are used.

Uploaded by

venkatraman1983
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
622 views4 pages

Verilog Code For PLL

This Verilog code defines a PLL module called pll3 that takes an input clock signal inclk0 and outputs a clock signal c0. It uses an altpll component to multiply the input clock frequency by 5 and divide it by 4 to generate c0, resulting in an output frequency that is 1.25 times the input frequency. The altpll component is configured through defparam statements to specify properties like clock frequencies, device family, and which ports are used.

Uploaded by

venkatraman1983
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

Verilog Code for PLL

module pll3 (
inclk0,
c0);

input inclk0;
output c0;

wire [5:0] sub_wire0;


wire [0:0] sub_wire4 = 1'h0;
wire [0:0] sub_wire1 = sub_wire0[0:0];
wire c0 = sub_wire1;
wire sub_wire2 = inclk0;
wire [1:0] sub_wire3 = {sub_wire4, sub_wire2};

altpll altpll_component (
.inclk (sub_wire3),
.clk (sub_wire0),
.activeclock (),
.areset (1'b0),
.clkbad (),
.clkena ({6{1'b1}}),
.clkloss (),
.clkswitch (1'b0),
.configupdate (1'b0),
.enable0 (),
.enable1 (),
.extclk (),
.extclkena ({4{1'b1}}),
.fbin (1'b1),
.fbmimicbidir (),
.fbout (),
.locked (),
.pfdena (1'b1),
.phasecounterselect ({4{1'b1}}),
.phasedone (),
.phasestep (1'b1),
.phaseupdown (1'b1),
.pllena (1'b1),
.scanaclr (1'b0),
.scanclk (1'b0),
.scanclkena (1'b1),
.scandata (1'b0),
.scandataout (),
.scandone (),
.scanread (1'b0),
.scanwrite (1'b0),
.sclkout0 (),
.sclkout1 (),
.vcooverrange (),
.vcounderrange ());
defparam
altpll_component.bandwidth_type = "AUTO",
altpll_component.clk0_divide_by = 4,
altpll_component.clk0_duty_cycle = 50,
altpll_component.clk0_multiply_by = 5,
altpll_component.clk0_phase_shift = "0",
altpll_component.compensate_clock = "CLK0",
altpll_component.inclk0_input_frequency = 10000,
altpll_component.intended_device_family = "Stratix II",
altpll_component.lpm_hint = "CBX_MODULE_PREFIX=pll3",
altpll_component.lpm_type = "altpll",
altpll_component.operation_mode = "NORMAL",
altpll_component.pll_type = "AUTO",
altpll_component.port_activeclock = "PORT_UNUSED",
altpll_component.port_areset = "PORT_UNUSED",
altpll_component.port_clkbad0 = "PORT_UNUSED",
altpll_component.port_clkbad1 = "PORT_UNUSED",
altpll_component.port_clkloss = "PORT_UNUSED",
altpll_component.port_clkswitch = "PORT_UNUSED",
altpll_component.port_configupdate = "PORT_UNUSED",
altpll_component.port_fbin = "PORT_UNUSED",
altpll_component.port_inclk0 = "PORT_USED",
altpll_component.port_inclk1 = "PORT_UNUSED",
altpll_component.port_locked = "PORT_UNUSED",
altpll_component.port_pfdena = "PORT_UNUSED",
altpll_component.port_phasecounterselect = "PORT_UNUSED",
altpll_component.port_phasedone = "PORT_UNUSED",
altpll_component.port_phasestep = "PORT_UNUSED",
altpll_component.port_phaseupdown = "PORT_UNUSED",
altpll_component.port_pllena = "PORT_UNUSED",
altpll_component.port_scanaclr = "PORT_UNUSED",
altpll_component.port_scanclk = "PORT_UNUSED",
altpll_component.port_scanclkena = "PORT_UNUSED",
altpll_component.port_scandata = "PORT_UNUSED",
altpll_component.port_scandataout = "PORT_UNUSED",
altpll_component.port_scandone = "PORT_UNUSED",
altpll_component.port_scanread = "PORT_UNUSED",
altpll_component.port_scanwrite = "PORT_UNUSED",
altpll_component.port_clk0 = "PORT_USED",
altpll_component.port_clk1 = "PORT_UNUSED",
altpll_component.port_clk2 = "PORT_UNUSED",
altpll_component.port_clk3 = "PORT_UNUSED",
altpll_component.port_clk4 = "PORT_UNUSED",
altpll_component.port_clk5 = "PORT_UNUSED",
altpll_component.port_clkena0 = "PORT_UNUSED",
altpll_component.port_clkena1 = "PORT_UNUSED",
altpll_component.port_clkena2 = "PORT_UNUSED",
altpll_component.port_clkena3 = "PORT_UNUSED",
altpll_component.port_clkena4 = "PORT_UNUSED",
altpll_component.port_clkena5 = "PORT_UNUSED",
altpll_component.port_enable0 = "PORT_UNUSED",
altpll_component.port_enable1 = "PORT_UNUSED",
altpll_component.port_extclk0 = "PORT_UNUSED",
altpll_component.port_extclk1 = "PORT_UNUSED",
altpll_component.port_extclk2 = "PORT_UNUSED",
altpll_component.port_extclk3 = "PORT_UNUSED",
altpll_component.port_sclkout0 = "PORT_UNUSED",
altpll_component.port_sclkout1 = "PORT_UNUSED",
altpll_component.spread_frequency = 0;

endmodule

Design Summary
Simulation Report

You might also like