Scribd
Upload
254 views2 pages

GP7000 Op Guide

This 3 sentence summary provides the essential information about operating the COLOR GPS/PLOTTER GP-7000: The OPERATOR'S GUIDE describes basic procedures for using the GP-7000, including using the range and cursor keys to adjust the scale and move the cursor, entering waypoints and routes, setting a destination, and configuring an arrival alarm. The GP-7000 has soft keys that change function based on the screen, card slots to insert memory cards, and hard keys for menu, display, waypoints, routes, and power functions. Navigation data like the own ship mark and plotter display are shown on the screen.

Uploaded by

arlindojl
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
254 views2 pages

GP7000 Op Guide

This 3 sentence summary provides the essential information about operating the COLOR GPS/PLOTTER GP-7000: The OPERATOR'S GUIDE describes basic procedures for using the GP-7000, including using the range and cursor keys to adjust the scale and move the cursor, entering waypoints and routes, setting a destination, and configuring an arrival alarm. The GP-7000 has soft keys that change function based on the screen, card slots to insert memory cards, and hard keys for menu, display, waypoints, routes, and power functions. Navigation data like the own ship mark and plotter display are shown on the screen.

Uploaded by

arlindojl
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

COLOR GPS/PLOTTER GP-7000

Operator’s Guide
The purpose of this Operator's Guide is to provide basic operating procedures for this
equipment. For more detailed information see the Operator's Manual.

RANGE key Cursor pad


Changes the range. Moves the cursor.
-: Shrinks the scale, and expands image.
+: Expands the scale, and shrinks image.

Hard keys
See below.

ENTER knob
Rotation: Selects
menu items.
Push: Confirms entry.

Soft keys
Change function according to screen Card slots
in use. Drive for chart/memory cards.

(Hard keys)
Key name Function
MENU key Shows/hides the menu bar.
DISP key Shows/hides DISPLAY MODE menu.
MOB/WPT key Short press: Enters a waypoint. Long press: Enters the MOB mark.
TLL/GOTO key Sets the waypoint or route as destination.
ROUTE key Creates the route.
CLEAR key Silences the audible alarm; erases the various windows one by one.
Long press: Turns power off.
POWER/BRILL key
Short press: Turns power on. Shows the BACKLIGHT window.
Cursor

Own ship
mark
Nav data

Plotter display

Returning Own Ship to Screen Entering Routes


Center 1. Operate the cursor pad to place the
Press the CENTER soft key. cursor at the position desired.
2. Press the ROUTE key, and then press
the SAVE soft key.
Adjusting Brilliance
3. Repeat steps 1 and 2 to complete the
1. Press the BRILL key to show the route.
BACKLIGHT window.
Setting Destination
Operate the cursor pad to place the cursor
on the waypoint you want to go, and then
2. Rotate the ENTER knob to adjust the press the GOTO key.
brilliance.
3. Push the ENTER knob to close the
Setting Arrival Alarm
window.
1. Press the MENU key.
Entering Waypoints 2. Choose ALARMS from the menu bar,
and then push the ENTER knob.
1. Operate the cursor pad to place the 3. Choose ARRIVAL ALARM and then
cursor at the position desired. push the ENTER knob.
2. Press the MOB/WPT key. Finally, press 4. Rotate the ENTER knob to choose the
the SAVE soft key. value, and then push it.
5. Enter the alarm range and then press
the SAVE soft key.

PUB.NO.OSE-44290-A1
(0409,HIMA) GP-7000
2

You might also like